Common Emitter Amplifier
Common Emitter Amplifier
Common Emitter Amplifier
The single stage common emitter amplifier circuit shown above uses what is commonly called
Voltage Divider Biasing. This type of biasing arrangement uses two resistors as a potential
divider network across the supply with their center point supplying the required Base bias
voltage to the transistor. Voltage divider biasing is commonly used in the design of bipolar
transistor amplifier circuits.
This method of biasing the transistor greatly reduces the effects of varying Beta, ( ) by holding
the Base bias at a constant steady voltage level allowing for best stability. The quiescent Base
voltage (Vb) is determined by the potential divider network formed by the two resistors, R1, R2
and the power supply voltage Vcc as shown with the current flowing through both resistors.
Then the total resistance RT will be equal to R1 + R2 giving the current as i = Vcc/RT. The
voltage level generated at the junction of resistors R1 and R2 holds the Base voltage (Vb)
constant at a value below the supply voltage.
Then the potential divider network used in the common emitter amplifier circuit divides the input
signal in proportion to the resistance. This bias reference voltage can be easily calculated using
the simple voltage divider formula below:
Bias Voltage
The same supply voltage, (Vcc) also determines the maximum Collector current, Ic when the
transistor is switched fully ON (saturation), Vce = 0. The Base current Ib for the transistor is
found from the Collector current, Ic and the DC current gain Beta, of the transistor.
Beta Value
Beta is sometimes referred to as hFE which is the transistors forward current gain in the common
emitter configuration. Beta has no units as it is a fixed ratio of the two currents, Ic and Ib so a
small change in the Base current will cause a large change in the Collector current. One final
point about Beta. Transistors of the same type and part number will have large variations in their
Beta value for example, the BC107 NPN Bipolar transistor has a DC current gain Beta value of
between 110 and 450 (data sheet value) this is because Beta is a characteristic of their
construction and not their operation.
As the Base/Emitter junction is forward-biased, the Emitter voltage, Ve will be one junction
voltage drop different to the Base voltage. If the voltage across the Emitter resistor is known then
the Emitter current, Ie can be easily calculated using Ohms Law. The Collector current, Ic can
be approximated, since it is almost the same value as the Emitter current.
This then establishes point A on the Collector current vertical axis of the characteristics curves
and occurs when Vce = 0. When the transistor is switched fully OFF, their is no voltage drop
across either resistor RE or RL as no current is flowing through them. Then the voltage drop
across the transistor, Vce is equal to the supply voltage, Vcc. This establishes point B on the
horizontal axis of the characteristics curves.
Generally, the quiescent Q-point of the amplifier is with zero input signal applied to the Base, so
the Collector sits half-way along the load line between zero volts and the supply voltage,
(Vcc/2). Therefore, the Collector current at the Q-point of the amplifier will be given as:
This static DC load line produces a straight line equation whose slope is given as: -1/(RL + RE)
and that it crosses the vertical Ic axis at a point equal to Vcc/(RL + RE). The actual position of the
Q-point on the DC load line is determined by the mean value of Ib.
As the Collector current, Ic of the transistor is also equal to the DC gain of the transistor (Beta),
times the Base current ( x Ib), if we assume a Beta () value for the transistor of say 100, (one
hundred is a reasonable average value for low power signal transistors) the Base current Ib
flowing into the transistor will be given as:
Instead of using a separate Base bias supply, it is usual to provide the Base Bias Voltage from the
main supply rail (Vcc) through a dropping resistor, R1. Resistors, R1 and R2 can now be chosen
to give a suitable quiescent Base current of 45.8A or 46A rounded off. The current flowing
through the potential divider circuit has to be large compared to the actual Base current, Ib, so
that the voltage divider network is not loaded by the Base current flow.
A general rule of thumb is a value of at least 10 times Ib flowing through the resistor R2.
Transistor Base/Emitter voltage, Vbe is fixed at 0.7V (silicon transistor) then this gives the value
of R2 as:
If the current flowing through resistor R2 is 10 times the value of the Base current, then the
current flowing through resistor R1 in the divider network must be 11 times the value of the Base
current. The voltage across resistor R1 is equal to Vcc 1.7v (VRE + 0.7 for silicon transistor)
which is equal to 10.3V, therefore R1 can be calculated as:
The value of the Emitter resistor, RE can be easily calculated using Ohms Law. The current
flowing through RE is a combination of the Base current, Ib and the Collector current Ic and is
given as:
Resistor, RE is connected between the Emitter and ground and we said previously that it has a
voltage of 1 volt across it. Then the value of RE is given as:
So, for our example above, the preferred values of the resistors chosen to give a tolerance of 5%
(E24) are:
Then, our original Common Emitter Amplifier circuit above can be rewritten to include the
values of the components that we have just calculated above.
Coupling Capacitors
In Common Emitter Amplifier circuits, capacitors C1 and C2 are used as Coupling Capacitors
to separate the AC signals from the DC biasing voltage. This ensures that the bias condition set
up for the circuit to operate correctly is not effected by any additional amplifier stages, as the
capacitors will only pass AC signals and block any DC component. The output AC signal is then
superimposed on the biasing of the following stages. Also a bypass capacitor, CE is included in
the Emitter leg circuit.
This capacitor is an open circuit component for DC bias meaning that the biasing currents and
voltages are not affected by the addition of the capacitor maintaining a good Q-point stability.
However, this bypass capacitor short circuits the Emitter resistor at high frequency signals and
only RL plus a very small internal resistance acts as the transistors load increasing the voltage
gain to its maximum. Generally, the value of the bypass capacitor, CE is chosen to provide a
reactance of at most, 1/10th the value of RE at the lowest operating signal frequency.
When the transistor is switched OFF, Vce equals the supply voltage Vcc and this is point B on
the line. Likewise when the transistor is fully ON and saturated the Collector current is
determined by the load resistor, RL and this is point A on the line.
We calculated before from the DC gain of the transistor that the Base current required for the
mean position of the transistor was 45.8A and this is marked as point Q on the load line which
represents the Quiescent point or Q-point of the amplifier. We could quite easily make life easy
for ourselves and round off this value to 50A exactly, without any effect to the operating point.
Point Q on the load line gives us the Base current Q-point of Ib = 45.8A or 46A. We need to
find the maximum and minimum peak swings of Base current that will result in a proportional
change to the Collector current, Ic without any distortion to the output signal.
As the load line cuts through the different Base current values on the DC characteristics curves
we can find the peak swings of Base current that are equally spaced along the load line. These
values are marked as points N and M on the line, giving a minimum and a maximum Base
current of 20A and 80A respectively.
These points, N and M can be anywhere along the load line that we choose as long as they are
equally spaced from Q. This then gives us a theoretical maximum input signal to the Base
terminal of 60A peak-to-peak, (30A peak) without producing any distortion to the output
signal.
Any input signal giving a Base current greater than this value will drive the transistor to go
beyond point N and into its cut-off region or beyond point M and into its Saturation region
thereby resulting in distortion to the output signal in the form of clipping.
Using points N and M as an example, the instantaneous values of Collector current and
corresponding values of Collector-emitter voltage can be projected from the load line. It can be
seen that the Collector-emitter voltage is in anti-phase (-180o) with the collector current.
As the Base current Ib changes in a positive direction from 50A to 80A, the Collector-emitter
voltage, which is also the output voltage decreases from its steady state value of 5.8v to 2.0v.
Then a single stage Common Emitter Amplifier is also an Inverting Amplifier as an increase
in Base voltage causes a decrease in Vout and a decrease in Base voltage produces an increase in
Vout. In other words the output signal is 180o out-of-phase with the input signal.
The Voltage Gain of the common emitter amplifier is equal to the ratio of the change in the
input voltage to the change in the amplifiers output voltage. Then VL is Vout and VB is Vin.
But voltage gain is also equal to the ratio of the signal resistance in the Collector to the signal
resistance in the Emitter and is given as:
We mentioned earlier that as the signal frequency increases the bypass capacitor, CE starts to
short out the Emitter resistor. Then at high frequencies RE = 0, making the gain infinite.
However, bipolar transistors have a small internal resistance built into their Emitter region called
Re. The transistors semiconductor material offers an internal resistance to the flow of current
through it and is generally represented by a small resistor symbol shown inside the main
transistor symbol.
Transistor data sheets tell us that for a small signal bipolar transistors this internal resistance is
the product of 25mV Ie (25mV being the internal volt drop across the Base/Emitter junction
depletion layer), then for our common Emitter amplifier circuit above this resistance value will
be equal to:
This internal Emitter leg resistance will be in series with the external Emitter resistor, RE, then
the equation for the transistors actual gain will be modified to include this internal resistance so
will be:
At low frequency signals the total resistance in the Emitter leg is equal to RE + Re. At high
frequency, the bypass capacitor shorts out the Emitter resistor leaving only the internal resistance
Re in the Emitter leg resulting in a high gain. Then for our common emitter amplifier circuit
above, the gain of the circuit at both low and high signal frequencies is given as:
At Low Frequencies
At High Frequencies
One final point, the voltage gain is dependent only on the values of the Collector resistor, RL and
the Emitter resistance, (RE + Re) it is not affected by the current gain Beta, (hFE) of the
transistor.
So, for our simple example above we can now summarise all the values we have calculated for
our common emitter amplifier circuit and these are:
Base Current
Collector Current
Output Voltage Swing
Amplifier Gain
Minimum
20A
2.0mA
2.0V
-5.32
Mean
50A
4.8mA
5.8V
Maximum
80A
7.7mA
9.3V
-218
A resistor can be included in the emitter leg in which case the voltage gain becomes -RL/RE. If
there is no external Emitter resistance, the voltage gain of the amplifier is not infinite as there is a
very small internal resistance, Re in the Emitter leg. The value of this internal resistance is equal
to 25mV/IE
In the next tutorial about Transistor Amplifiers we will look at the Junction Field Effect
Amplifier commonly called the JFET Amplifier. Like the transistor, the JFET is used in a single
stage amplifier circuit making it easier to understand. There are several different kinds of field
effect transistor that we could use but the easiest to understand is the junction field effect
transistor, or JFET which has a very high input impedance making it ideal for amplifier circuits.
Amplifier Classes
Amplifier Distortion
Amplifiers Summary
Class A Amplifier
Class B Amplifier
Emitter Resistance
Frequency Response
Transistor Biasing
Older comments
1.
monii rithic
vry useful
February 28th, 2015