Design Solar PV System

Design Solar PV System
1. Determine power consumption demands

The first step in designing a solar PV system is to find out the
total power and energy consumption of all loads that need to be
supplied by the solar PV system as follows:
1.1 Calculate total Watt-hours per day for each
appliance used.
Add the Watt-hours needed for all appliances together to
get the total Watt-hours per day which must be delivered to the
appliances.
1.2 Calculate total Watt-hours per day needed from the
PV modules.
Multiply the total appliances Watt-hours per day times 1.3
(the energy lost in the system) to get the total Watt-hours per
day which must be provided by the panels.
2. Size the PV modules

Different size of PV modules will produce different amount of
power. To find out the sizing of PV module, the total peak watt
produced needs. The peak watt (Wp) produced depends on size of
the PV module and climate of site location. We have to consider
panel generation factor which is different in each site location.
For Thailand, the panel generation factor is 3.43. To determine the
sizing of PV modules, calculate as follows:
2.1 Calculate the total Watt-peak rating needed for PV
modules
Divide the total Watt-hours per day needed from the PV
modules (from item 1.2) by 3.43 to get the total Watt-peak rating
needed for the PV panels needed to operate the appliances.
2.2 Calculate the number of PV panels for the system
Divide the answer obtained in item 2.1 by the rated output
Watt-peak of the PV modules available to you. Increase any
fractional part of result to the next highest full number and that
will be the number of PV modules required.
Result of the calculation is the minimum number of PV panels. If
more PV modules are installed, the system will perform better and
battery life will be improved. If fewer PV modules are used, the
system may not work at all during cloudy periods and battery life
will be shortened.
3. Inverter sizing
An inverter is used in the system where AC power output is
needed. The input rating of the inverter should never be lower
than the total watt of appliances. The inverter must have the
same nominal voltage as your battery.
For stand-alone systems, the inverter must be large enough to
handle the total amount of Watts you will be using at one time.
The inverter size should be 25-30% bigger than total Watts of
appliances. In case of appliance type is motor or compressor then
inverter size should be minimum 3 times the capacity of those
appliances and must be added to the inverter capacity to handle
surge current during starting.
For grid tie systems or grid connected systems, the input rating
of the inverter should be same as PV array rating to allow for safe
and efficient operation.
4. Battery sizing
The battery type recommended for using in solar PV system is
deep cycle battery. Deep cycle battery is specifically designed for
to be discharged to low energy level and rapid recharged or cycle
charged and discharged day after day for years. The battery
should be large enough to store sufficient energy to operate the
appliances at night and cloudy days. To find out the size of
battery, calculate as follows:
4.1 Calculate total Watt-hours per day used by appliances.
4.2 Divide the total Watt-hours per day used by 0.85 for
battery loss.
4.3 Divide the answer obtained in item 4.2 by 0.6 for depth of
discharge.
4.4 Divide the answer obtained in item 4.3 by the nominal
battery voltage.
4.5 Multiply the answer obtained in item 4.4 with days of
autonomy (the number of days that you need the system to
operate when there is no power produced by PV panels) to get the
required Ampere-hour capacity of deep-cycle battery.
Battery Capacity ( Ah )
Total Watthours per day used by appliances x Days of autonomy

(0.85 x 0.6 x nominal battery voltage)
5. Solar charge controller sizing

The solar charge controller is typically rated against Amperage
and Voltage capacities. Select the solar charge controller to match
the voltage of PV array and batteries and then identify which type
of solar charge controller is right for your application. Make sure
that solar charge controller has enough capacity to handle the
current from PV array.the sizing of controller depends on the total
PV input current which is delivered to the controller and also
depends on PV panel configuration (series or parallel
configuration).According to standard practice, the sizing of solar
charge controller is to take the short circuit current (Isc) of the PV
array, and multiply it by 1.3 Solar charge controller rating = Total
short circuit current of PV array x 1.3
1. Determine power consumption demands

Total appliance use=P t=261 Wh/day
Total PV panels energy needed =261 1.3=340 Wh /day
2- Size the PV panel

Total of PV panel capacity needed =340/ 3.4=100 W P
Number of PV panelsneeded =100/100=1
So this system should be powered by at least 1 modules of 100 Wp PV module.
3. Inverter sizing
The inverter 300
4. Battery sizing
Nominal battery voltage =12v
Days of autonomy=1
Battery capacity=
(2611)
=43
( 0.850.612)
Total Ampere-hours required 43 Ah, So the battery should

be rated 12 V 50 Ah for 1 day autonomy.
5. Solar charge controller sizing

Solar charge controller ratin=Total short circuit current of PV array x 1.3

Design Solar PV System

Uploaded by

Copyright:

Available Formats

Design Solar PV System

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design Solar PV System

Uploaded by

Copyright:

Available Formats

Design Solar PV System

1. Determine power consumption demands

2. Size the PV modules

Total Watthours per day used by appliances x Days of autonomy

5. Solar charge controller sizing

1. Determine power consumption demands

Total PV panels energy needed =261 1.3=340 Wh /day

2- Size the PV panel

So this system should be powered by at least 1 modules of 100 Wp PV module.

Total Ampere-hours required 43 Ah, So the battery should

5. Solar charge controller sizing

You might also like