Module 1 Production of Materials

Production of Materials
1.1

Energy and Raw Materials from Fossil Fuels

1.1.1

Identify the industrial source of ethylene from the cracking of some of the fractions

from the refining of petroleum

Petroleum is a mixture of crude oil and natural gas.

Fractional distillation is used to separate crude oil into fractions according to their boiling point
ranges (each fraction contains hydrocarbons of similar molecular weight). Lighter fractions with
lower boiling point rise higher in the column.

The main industrial source of ethylene is from the cracking of fractions obtained from the refining
of petroleum. Low-demand, long-chain hydrocarbons are cracked to produce smaller chains such
as ethylene, which is the starting product for many synthesis reactions.

Steam (thermal) cracking:

Cracking of petroleum fractions was initially achieved by thermal cracking, where the fraction
is heated to high temperatures (1000 C) in the absence of air.

In Australia, steam cracking is the major industrial source of ethylene for the petrochemical
industry. It provides a high yield of ethylene, as the reaction is endothermic.

Ethane (

), which is obtained from petroleum and natural gas, is mixed with steam and

passed through hot metal coils to form ethylene and hydrogen:

( )

( )

( )

( )

( )
( )

Catalytic cracking:

Catalytic cracking is the process of breaking long-chain hydrocarbons into smaller chains.
Zeolite is used as a catalyst, allowing lower temperatures (500 C) to be used.
()

( )

()

This process uses less heat than thermal cracking, but it cannot decompose large molecules
(C15-C25) completely into ethylene, so it is insufficient in meeting the demands of industry.
()

()

()

1.1.2

( )

()
( )

Identify that ethylene, because of the high reactivity of its double bond, is readily

transformed into many useful products

Alkanes and their corresponding alkenes are non-polar carbon chain molecules with weak
dispersion forces between the molecules. Their physical properties (e.g. melting point and
solubility) are due to intermolecular forces and thus are similar.

The chemical properties of alkanes and alkenes are very different. The presence of the carboncarbon double bond in alkenes makes them much more reactive than alkanes. Alkanes are
saturated as they only have carbon-carbon single bonds, and so are unreactive. Alkenes are
unsaturated and hence more reactive, as they undergo addition reactions readily.

Ethylene has a highly reactive double bond (a site of high electron cloud
density) which allows it to undergo polymerisation. The double bond breaks
open to form two single bonds.

Module 1 Production of Materials

Useful products derived from ethylene:

Process

Product

Polymerisation
Hydration
Halogenation

Polyethylene
Ethanol
Polyvinyl chloride

Formula
(
)
(

Use
Plastic
Solvents, antiseptics
Pipes, insulation

Alkanes undergo substitution reactions, where an atom in a molecule is replaced by another

atom or group of atoms.
()

()

()

Alkenes commonly react with molecules (e.g.

()

) through addition reactions,

where a small molecule adds across a double or triple bond of a hydrocarbon molecule.

Hydrogenation:

This is an addition reaction in which hydrogen adds onto an unsaturated molecule:

( )

( )

Ethylene is reacted with water, using a phosphoric acid catalyst, to produce ethanol:
( )

()

Reactive molecules from the halogen group (

( )

( )

A hydrohalogen (e.g.

or

) can all react with ethylene:

()

) and ethylene react to form a haloethane

( )

Hydrohalogenation:

1.1.3

()

Halogenation:

( )

Hydration:

( )

( )

Identify that ethylene serves as a monomer from which polymers are made

Ethylene serves as a monomer from which polymers are made. It is the starting material for the
production of other commercially significant monomers such as chloroethene and phenylethene.

Ethylene undergoes addition polymerisation due to its reactive double bond.

1.1.4

Identify polyethylene as an addition polymer and explain the meaning of this term

Polymers are long-chain molecules composed of repeating sub-units called monomers.

Addition polymerisation is the polymerisation of monomers by an addition reaction.
An addition polymer forms when small monomers (e.g. ethylene) add together to produce
longer chain molecules called polymers (e.g. polyethylene), and no other product.

In addition polymerisation, the monomers add to the growing polymer chain so that all atoms
present in the monomer are present in the polymer. There is no gain or loss of atoms.

One of the bonds in the

double bond is broken, providing each carbon atom with extra

bonding capacity, which it uses to form single bonds between the monomers.

Polyethylene is an addition polymer made from the monomer ethylene:

(
2

Module 1 Production of Materials

1.1.5

Outline the steps in the production of polyethylene as an example of a commercially

and industrially important polymer

1.1.6

Analyse information from secondary sources such as computer simulations, molecular

model kits or multimedia resources to model the polymerisation process

Addition polymerisation requires a catalyst or initiator molecule to start the reaction. Once it is
underway, the reaction proceeds rapidly as addition polymerisation is a chain reaction (it is also
known as chain-growth polymerisation).

Stages in the production of polyethylene:

Initiation

The initiator molecule (e.g. peroxide) decomposes to form reactive free radicals.

The free radicals break the double bond of an ethylene monomer to form an ethylene free
radical.

Propagation

This ethylene free radical (

activated monomer) reacts with another ethylene

monomer, and this process continues with the polymer chain length increasing (i.e. chain
growth occurs).

Termination

When two free radical ethylene chains combine, a complete polyethylene molecule is
formed and the process stops.
(
)

An inhibitor is added to halt the formation of free radicals. This can occur at any time, so the size
and molecular weight of polymer chains can be regulated.

Methods used to produce polyethylene:

High pressure method

This process uses high temperature and pressure and an initiator molecule (e.g. organic
peroxide). This initiator is not a catalyst as it is incorporated into the final polymer formed.

This creates low-density polyethylene (LDPE) which has significant chain branching, i.e.
branched chains of polyethylene that cannot be packed together tightly.

This results in a soft, flexible, low density plastic with low melting point (due to low
dispersion forces between chains).

Ziegler-Natta process

This process uses a much lower temperature and pressure and a transition metal catalyst
(Ziegler-Natta catalyst).

This creates high-density polyethylene (HDPE), i.e. unbranched, linear polyethylene

molecules that can be packed together very densely.

Extensive dispersion forces make HDPE stronger and less flexible than LDPE.

In both these processes, the initiator or catalyst activates an ethylene molecule by attaching to it.

Module 1 Production of Materials

1.1.7

Identify vinyl chloride and styrene as commercially significant monomers by both their

systematic and common names

1.1.8

Describe the uses of the polymers made from the above monomers in terms of their

properties

Ethylene

Polymer: polyethylene

Uses of polyethylene:

Low-density polyethylene (highly branched):

The extensive chain-branching of LDPE makes it relatively soft and flexible so it is used
in making plastic cling wrap and plastic bags.

High-density polyethylene (unbranched):

HDPE has no chain branching so linear polymer chains pack closely together, held
tightly by dispersion forces. This results in the polymer being rigid and hard, so it is
used in making durable items such as kitchen utensils and containers and rubbish
bins.

Vinyl chloride

Systematic name: chloroethene

Vinyl chloride is an ethylene molecule with a

Polymer: polyvinyl chloride (PVC).

Vinyl chloride

atom substituted with a

atom.

Polyvinyl chloride

Uses of polyvinyl chloride:

PVC is hard, inflexible and brittle, and the large

These rigid forms of PVC can be used for drainage and sewage pipes and guttering.

Softer PVC can be produced by adding a plasticiser, which decreases the dispersion forces
between the polymer chains and makes the polymer more flexible. This makes PVC useful
for electrical insulation and flexible tubing.

Styrene

Systematic name: phenylethene or ethenyl benzene

Styrene is an ethylene molecule with an

Polymer: polystyrene (PS)

atom replaced by a benzene ring (a 6C ring with

alternating double bonds).

Styrene

Polystyrene

Module 1 Production of Materials

Uses of polystyrene:

Polystyrene is electrically insulative and very hard and rigid due to the presence of the
large side group benzene rings along the polymer chains. This makes it suitable for car
battery cases and tool handles.

The minimal chain branching also makes polystyrene very crystalline, so it can be formed
into clear, transparent objects such as drinking glasses and CD cases.

If gas is bubbled through the polymer as it forms, styrofoam is formed. Styrofoam is used
for insulation and packaging as it is a good heat insulator and shock absorber.

1.1.9

Identify data, plan and perform a first-hand investigation to compare the reactivities of

appropriate alkenes with the corresponding alkanes in bromine water

Aim: To compare the reactivity of cyclohexane and cyclohexene bromine water.

Equipment: two test tubes, cyclohexane, cyclohexene, 0.01

bromine water.

Method:
1.

of cyclohexane was added to one test tube and 2

of cyclohexene was added to the

other test tube.

2.

of bromine water was added to each liquid and the test tubes were shaken to the same

extent.
3.

The test tubes were left to settle, and then observed.

Cyclohexene and cyclohexane were used (instead of ethylene or propene) because:

C1 to C4 are gases at room temperature and would be hard to manage. Cyclohexene is a

clear, colourless liquid and bromine water is an aqueous brown/yellow solution.

Cyclohexene/cyclohexane is more stable, less toxic and has a longer shelf-life than
hexene/hexane.

Results: It was observed that the cyclohexene immediately decolourised the bromine water
from yellow to colourless, while the cyclohexane remained yellow. This showed which
hydrocarbon decolourised the bromine water, allowing them to be distinguished from each other.
The cyclohexene reacted with the bromine water, forming 1,2-dibromocyclohexane.
()

()

Risk Assessment:

Safety goggles were worn to protect from splashing of any solutions.

Organic hydrocarbons (cyclohexene and cyclohexane) are highly volatile and flammable so
they were kept away from heat sources or flames at all times. They also release moderately
toxic vapour, so only small quantities were used and a fume cupboard was used to perform
the experiment. Experimental time was kept to a minimum.

Bromine water is highly toxic if ingested and is slightly corrosive.

Module 1 Production of Materials

1.2

Materials from Biomass

1.2.1

Discuss the need for alternative sources of the compounds presently obtained from the

petrochemical industry

Fossil fuels such as crude oil and natural gas are non-renewable resources. Consumption of these
resources has accelerated in the last century and these fossil fuels could be completely used up
within the next few decades.

Alternative sources of compounds must be developed to meet future energy and material needs.

Ethanol is the main alternative source of ethylene, as it can be produced by fermentation of

starch and sugars, and can be easily converted to ethylene.

Cellulose (a major component of renewable biomass) is a major source of carbon compounds

as it contains the basic carbon chain structures needed to build compounds presently
obtained from petrochemicals, and is relatively abundant.

1.2.2

Biopolymers, produced using enzymes and bacteria, could also be a replacement for plastics.
Identify that cellulose contains the basic carbon-chain structures needed to build

petrochemicals and discuss its potential as a raw material

Cellulose consists of 6C glucose units so it contains the basic carbon-chain structures needed to
build petrochemicals for use as fuels or raw materials in the production of polymers.

Cellulose has great potential as a raw material because it is renewable, readily available in large
amounts and can be converted to petrochemicals, reducing our reliance on petroleum (which is
a non-renewable resource).

Cellulose can be converted to products that can be readily metabolised and used as a food
source. For example, the acid hydrolysis of cellulose to form glucose:

()

( )

The existing polymer chains in cellulose can be modified to make new polymers (e.g. rayon).

Cellulose can be broken down into smaller molecules to produce a source of carbon
compounds which can be used to make new synthetic polymers. Ethanol, derived from
glucose, can be decomposed to form ethylene, an important starting chemical in the
production of plastics.

However, there is currently no efficient method of cellulose decomposition, due to difficulties in

hydrolysing cellulose. The conversion of cellulose to ethylene via ethanol has high energy
requirements, and is much more expensive than current methods of obtaining ethylene.

Nevertheless, scientific research continues to develop more efficient and low-cost ways of using
cellulose as a raw material. Thus, in the future, biomass (renewable) could be used instead of fossil
fuels (non-renewable) to make polymers.

1.2.3

Explain what is meant by a condensation polymer

A condensation polymer is one that forms by the elimination of a small molecule (often water)
when pairs of monomers join together.

Natural polymers include cellulose, starch, protein and DNA.

All biological polymers, such as proteins and starch, are condensation polymers.

Manufactured polymer fabrics include silk, polyester and nylon.

Module 1 Production of Materials

1.2.4

Describe the reaction involved when a condensation polymer is formed

In condensation polymerisation, the functional groups of the two monomers react, forming a
new bond and releasing water.

Example:

Proteins are condensation polymers made from amino acids.

Amino acids contain the amine group (

) and carboxylic acid group (

).

A hydrogen from the amine end of the molecule combines with the hydroxyl group on
the acid end of another molecule to create water.

The carboxylic acid group (

amide link (

1.2.5

) combines with an amine group (

) to form an

).

Continued condensation polymerisation produces a protein.

Describe the structure of cellulose and identify it as an example of a condensation

polymer found as a major component of biomass

Cellulose is the most abundant polymer on Earth and is a major component of biomass, which is a
renewable resource. Biomass is carbon-based matter, and serves as a source of chemically
modified cellulose-based polymers, such as rayons, cellulose nitrate and acetate.

Cellulose is a biopolymer formed by the condensation polymerisation of -glucose monomers.

(

( )

Cellulose is a very long condensation polymer containing thousands of -glucose units in

long chains.

The -glucose monomers are linked by a -1,4 glycosidic bond.

Cellulose has a linear structure because the bulky

groups on

The

are on alternate sides of adjoining glucose units.

groups form hydrogen bonds that hold cellulose chains

together. This creates long, rigid cellulose fibres which account

for the strength of wood as a building material.

()

The reduced availability of

groups, due to their involvement

in hydrogen bonding between chains, makes cellulose

insoluble in water. The structure of cellulose exposes few
groups to water molecules.

Module 1 Production of Materials

1.2.6

Use available evidence to gather and present data from secondary sources and analyse

progress in the recent development and use of a named biopolymer. This analysis should name
the specific enzyme(s) used or organism used to synthesise the material and an evaluation of
the use or potential use of the polymer produced related to its properties

Biopolymers are naturally occurring polymers found in living organisms.

Biopolymer: Biopol

This biopolymer is called PHBV (poly-3-hydroxybutyrate-poly-3-hydroxyvalerate).

It is a co-polymer of polyhydroxybutyrate (PHB) and polyhydroxyvalerate (PHV).

The monomer of PHB is 3-hydroxybutanoic acid (common name 3-hydroxybutyric acid).

The monomer of PHV is 3-hydroxypentanoic acid (common name 3-hydroxyvaleric acid).

Production:

This polymer is produced industrially by bacteria (Ralstonia eutrophus or Alcaligenes

eutrophus) growing in tanks with a carbon-based food source, high in glucose or valeric acid.

The bacteria manufacture the PHBV which is stored in their cell walls as granules for later use
as an energy source.

The polymer is then isolated and purified.

Uses in relation to properties:

Biopol is mainly used in medical applications (e.g. surgical stitches and tissue scaffolding) as it
is biocompatible (

) and biodegradable (products

decompose naturally and no surgery is needed to remove them).

The use of biopolymers in medicine will mean more lives can be saved due to biopolymer
transplants and fewer allergic reactions.

Biopol is also used to make disposable items (e.g. bottles, razors and shampoo containers) as it
is biodegradable and non-toxic. However, this is uncommon now, due to the high cost of
production.

Recent developments:

Recently, the gene for producing Biopol polymer strands from the Alcaligenes eutrophus
bacteria was extracted and implanted into E. coli using genetic engineering techniques. E. coli
bacteria are much easier to grow than other bacteria, and thus are cheaper.

Scientists have also attempted to genetically engineer plants such as cress so that they
produce biodegradable plastics rather than storing starch. This results in a much cheaper
process, although it is still more expensive than petrochemical polymers.

Evaluation:

Biopol is currently much more expensive than petrochemical plastics, so research is being
carried out to genetically modify bacteria to control the plastic that they form. There is a
growing demand for it where biodegradability and biocompatibility are important.

It has an advantage over petroleum-based polymers of being renewable, as it is formed from

a microorganism. Biodegradable polymers may eventually replace petroleum-based polymers,
reducing our dependence on fossil fuels and allowing them to last longer.

Module 1 Production of Materials

1.3

Ethanol - Use and Manufacture

1.3.1

Describe the dehydration of ethanol to ethylene and identify the need for a catalyst in

this process and the catalyst used

The dehydration of ethanol involves the removal of a water molecule from ethanol, forming
ethylene.
()

( )

()

Ethanol is dehydrated by heating it with a catalyst (concentrated

and

), which breaks the

bonds, allowing the formation of a double bond and water. The catalyst also

provides an alternate pathway with a lower activation energy.

1.3.2

Sulfuric acid is chosen because it is a strong dehydrating agent (absorbs water).

Describe the addition of water to ethylene resulting in the production of ethanol and

identify the need for a catalyst in this process and the catalyst used

The hydration of ethanol involves the addition of a water molecule to ethylene, forming ethanol.
( )

()

Hydration also needs heat and a catalyst (dilute

()

) which opens the double bond and allows

water to attach. Water itself is not reactive enough to break the ethylene double bond.
1.3.3

Describe and account for the many uses of ethanol as a solvent for polar and non-polar

substances

Ethanol is a clear, colourless liquid that has a lower boiling point than water. It is volatile and its
vapours form combustible mixtures with air.

Uses:

The major uses of ethanol are as a motor fuel supplement and as a solvent.

Ethanol is used as a solvent in cosmetics (e.g. perfumes) and toiletries, medicinal preparations
(e.g. antiseptics) and food colourings and dyes.

It is also an industrial solvent for paints, oils and fatty acids.

Ethanol is able to act as a solvent for polar and non-polar substances due to its unique molecular
structure.

The

group is the polar hydroxyl end, which interacts with other polar molecules through

dipole-dipole forces or hydrogen bonds. This favours the solubility of polar substances (e.g. glucose,
carboxylic acids) in ethanol. Ethanol dissolves in water in all proportions due to the strong
hydrogen bonding between the two liquids.

The

group is the non-polar alkyl chain end, which interacts with non-polar substances

through dispersion forces. This favours the solubility of non-polar substances (e.g. hydrocarbons,
oils) in ethanol. Non-polar iodine also readily dissolves in ethanol.
1.3.4

Present information from secondary sources by writing a balanced equation for the

fermentation of glucose to ethanol

Fermentation is a process in which glucose is broken down to ethanol and carbon dioxide by the
action of enzymes present in yeast.
(

( )

Module 1 Production of Materials

1.3.5

Describe conditions under which fermentation of sugars is promoted

The conditions under which fermentation is promoted:

A suitable grain or fruit (plant material with a high content of starch or simple sugars ) is
mashed up with water.

The presence of yeast.

The exclusion of air (anaerobic environment).

The temperature is kept at about 37C.

The ethanol concentration is kept below 15%, as yeast cannot function effectively above this
concentration.

1.3.6

Approximately neutral pH.

Summarise the chemistry of the fermentation process

Yeast is first added to mashed grain and water.

Enzymes (biological catalysts) in the mixture convert any starch or sucrose (

) into

glucose or fructose.
(

()

The yeast use their enzymes to convert glucose or fructose into ethanol and carbon dioxide.
(

( )

Yeast can produce ethanol concentrations of up to about 15%, after which the yeast die and
fermentation stops. Fractional distillation is required to obtain higher ethanol concentrations
(95%). This produces common industrial or laboratory alcohol. To obtain 100% ethanol, more
complex distillation procedures are needed to completely remove water, due to the strong
hydrogen bonding between ethanol and water.

1.3.7

Process information from secondary sources to summarise the processes involved in the

industrial production of ethanol from sugar cane

In the production of sugar (sucrose) from sugarcane, a by-product is a concentrated solution of

sucrose called molasses. This can be used to produce ethanol by fermentation:

The harvested sugarcane is crushed to extract the juices that contain sucrose.

The sucrose is extracted and crystallised, leaving the remaining liquor (molasses) with a high
percentage of sucrose.

Water is added to the molasses syrup to reduce the sucrose concentration, and acid is added
to prevent bacterial growth.

The mixture in the fermentation tank is adjusted to the desired temperature (37C) and yeast
is added.

Fermentation begins and the carbon dioxide gas that evolves is collected and sold to other
industries.

After a few days the fermentation is complete, and the mixture is passed through rectifying
columns to purify it.

The final mixture is distilled to produce 95% ethanol.

10

Module 1 Production of Materials

1.3.8

Outline the use of ethanol as a fuel and explain why it can be called a renewable

resource

Ethanol is able to undergo combustion, so it can be used as a fuel.

()

( )

( )

( )

Ethanol is a renewable resource as it is manufactured from carbohydrates such as glucose and

starch that are produced by photosynthesis in plants. The products of its combustion (

and

) are the reactants needed by plants for photosynthesis.

( )

1.3.9

()

( )

Assess the potential of ethanol as an alternative fuel and discuss the advantages and

disadvantages of its use

Potential of ethanol as an alternative fuel:

As supplies of petroleum dwindle, the development of renewable fuels such as ethanol

becomes an important area of research.

Ethanol is a liquid, which makes it an easily transportable fuel that is a possible alternative fuel
for automobiles.

Advantages of using ethanol as a fuel:

It is a renewable resource that is derived from biomass.

It undergoes complete combustion more readily than fossil fuels:

The oxygen atom in the ethanol molecule ensures that less oxygen is needed for complete
combustion. Ethanol also contains less carbon than octane, the major component of
petrol. It produces only

and

as by-products.

Thus, ethanol is a cleaner and more efficient fuel that has reduced greenhouse gas
emissions.

Disadvantages of using ethanol as a fuel:

Ethanol has a lower heat of combustion than petrol so it does not release as much energy
on complete combustion. Cars can travel further with the same amount of octane than
ethanol, so ethanol is more expensive than petrol.

Engines must be modified to run on high ethanol mixtures (e.g. E25).

Large areas of arable land are needed to grow crops to use in the production of ethanol, at
the expense of other farming industries. This leads to environmental problems such as soil
erosion, deforestation, fertiliser runoff and salinity.

Disposal of fermentation wastes in the production of ethanol also presents major

environmental issues.

Evaluation:

Currently, ethanol has potential as an alternative fuel and a future replacement for fossil fuels,
particularly for transport. However, further research into developing more efficient methods of
ethanol production is required before it can become an economically viable proposition.

Note: E

produced when it burns is balanced by the

, . .

used in photosynthesis to produce crops to

be later converted to ethanol. However, significant energy input is required for the production of
fertilisers and the distillation process. This comes from the combustion of fossil fuels, which leads
to the release of carbon dioxide. Nevertheless, the combustion of ethanol does have a lower
greenhouse impact compared with the combustion of petrol.

11

Module 1 Production of Materials

1.3.10 Process information from secondary sources to summarise the use of ethanol as an
alternative car fuel, evaluating the success of current usage

Ethanol is mainly used (mixed with petrol) as a fuel to supplement petrol supplies. Petrol
containing 10% ethanol can be used in normal petrol engines without engine modification.

Brazil

ethanol. Since the 1970s, its major fuel for cars has been

ethanol.

However, Brazil has struggled with the higher costs of producing ethanol compared with
petrol, and subsidies are needed before it is economically viable.

In the US and Canada, a biofuels program has been adopted, which grants tax concessions to
ethanol producers. Ethanol is used in a fuel called gasohol (10% ethanol, 90% gasoline).

In Australia, ethanol is generally considered an uneconomic proposition due to the high costs of
production.

Mainly, Australia lacks the arable land to grow sufficient sugar cane crops to make ethanol an
important contributor to liquid fuel demands.

Subsidies and tax concessions have been set up to encourage the production of ethanol to be
added to petrol (mainly to reduce oil consumption). There is increasing acceptance of
ethanol/petrol blends (e.g. E10, which contains 10% ethanol) that have no detrimental effect
on vehicles.

It is expected that, in the future, as the price of petrol increases, ethanol/petrol blends will be
more widely used in Australia.

1.3.11 Define the molar heat of combustion of a compound and calculate the value for ethanol
from first-hand data

The molar heat of combustion of a substance is the heat liberated when one mole of the
substance undergoes complete combustion with oxygen at standard temperature and pressure,
with the final products being carbon dioxide gas and liquid water.

The molar heat of combustion is the positive quantity of the enthalpy change for the
combustion process.

change in heat ( )

mass of system (

change in temperature ( )

specific heat capacity of

substance (

)
)

The molar heat of combustion for ethanol:

()

( )

( )

()

1.3.12 Solve problems, plan and perform a first-hand investigation to carry out the
fermentation of glucose and monitor mass changes

Aim: To ferment a sucrose solution and monitor the mass changes involved.
Equipment: balance, conical flask, sucrose, table salt, dried yeast, limewater

).

Method:
1.

The fermentation mixture of water, sugar, salt and yeast were placed into a conical flask,
swirled to mix and then weighed.

2.

Another conical flask was half filled with limewater and weighed.

12

Module 1 Production of Materials

3.

Both containers were stoppered and connected by a rubber hose. The yeast beaker was
placed in a water bath at a constant temperature (37C).

4.

The appearance and weight of the fermentation mixture and limewater were recorded daily
for a week.

Results:

The yeast flask became milky, foamy and smelt of alcohol, proving that ethanol was produced.

Limewater turned cloudy. This proved that carbon dioxide gas was produced.
( ) ( )
( )
( )
()

As the mass of the yeast flask steadily decreased each day (due to the

inevitably

escaping), the limewater flask also gained approximately the same mass.

Risk Assessment: Safety glasses were worn throughout this experiment.

1.3.13 Identify data sources, choose resources and perform a first-hand investigation to
determine and compare heats of combustion of at least three liquid alkanols per gram and per
mole

Aim: To determine and compare the heats of combustion of ethanol, methanol and 1-butanol
(these are short-chained alkanols and so are most likely to undergo complete combustion). The
method used to determine the heat of combustion of fuels is calorimetry, which involves
determining the heat released or absorbed by a reaction by measuring the temperature change of
the surroundings:

Equipment: ethanol, methanol, 1-butanol, tin can (better thermal conductor than a glass beaker),
balance, thermometer, matches.

Method:
1.

The mass, temperature and volume of water and the mass of each alkanol were recorded.

2.

Each alkanol, in a spirit burner, was used to heat 150

of water in a tin can. A thermometer

was used to stir the water and measure the temperature.

3.

After 10 minutes, the spirit burner was capped and immediately reweighed, and the final
temperature was recorded.

Results: In order of increasing

: methanol, ethanol, 1-butanol

Discussion:

As molecular mass increases, the number of

bonds need to be created in the products (
energy, this leads to an increase in

The experimental value of

and
and

bonds increases and more

). Since bond formation releases

may have been less than the theoretical value because:

Chemical reason: The molar heat of combustion refers only to complete combustion
under standard temperature and pressure. The yellow flames and soot that formed
indicated that the combustion was incomplete (i.e. less than maximum energy is released).

Physical reason: Heat was lost from the tin can to the surrounding air or the tripod, which
would reduce accuracy.

To obtain more accurate experimental data:

Use a can container (conducts heat better) instead of a glass beaker.

Ensure that the container is as close to the flame of the spirit burner as possible.

Use a draught shield to minimise heat loss.

Risk Assessment:

Alkanols are flammable so the bulk supply was kept well away from the burner and matches.

13

Module 1 Production of Materials

1.4

Energy from Redox Reactions

1.4.1

Explain the displacement of metals from solution in terms of transfer of electrons

A displacement reaction is a reaction in which a metal converts the ion of another metal into a
neutral atom.

Active metals will displace less active metal ions from solution. The more active metal atom loses
one or more electrons and becomes a positive ion. The electrons lost are transferred to the ions of
the less active metal, resulting in them becoming metal atoms.

e.g. Zinc metal will displace copper ions from solution:

( )

(
(

( )

Solid

( )
)

( )

The
ions to

1.4.2

oxidation (zinc loses electrons)

reduction (copper gains electrons)
redox reaction
ions in solution. The
ions in solution are

metal.

metal is the reductant (reducing agent), i.e. electron donor, that reduces the
metal. The

that oxidises the

metal dissolves to produce

converted to solid

The electrons lost by

ions form the oxidant (oxidising agent), i.e. electron acceptor,

metal to

ions.

atoms undergoing oxidation are used to reduce

ions to

atoms.

Identify the relationship between displacement of metal ions in solution by other

metals to the relative activity of metals

Referring to the table standard reduction potentials on the HSC Chemistry Data Sheet, a metal
higher up in the series is more reactive and will displace a metal ion lower down from solution.

Therefore, a spontaneous redox reaction will occur if the reductant (species undergoing oxidation)
is higher in the table of standard reduction potentials than the oxidant (species undergoing
reduction).

The further apart the ions are (the greater the difference in activity between the two metals), the
more vigorous the displacement reaction (and thus more energy released).

Reactions between acids and metals are exothermic. The higher the metal in the activity series,
the greater the heat liberated in its reaction with an acid.

1.4.3

Account for changes in the oxidation state of species in terms of their loss or gain of

electrons

For monatomic ions, the oxidation state of the element is the charge on the ion (including sign).

It is a number given to an atom to indicate the number of electrons it has lost or gained.

Rules for oxidation states:

All atoms in elemental form have oxidation number zero (e.g.

Neutral molecules have oxidation number zero (e.g.

Monatomic ions have oxidation number equal to their charge (e.g.

Polyatomic ions have oxidation number equal to their charge, and the sum of the oxidation
states of the atoms equals this number (e.g.

Oxygen always has oxidation number

Hydrogen always have oxidation number

, where it is

(except in peroxide,

).

).
,
,
, where it is

).
).
).

(except in metal hydrides, e.g. sodium hydride,

).

14

Module 1 Production of Materials

In general:

Oxidation is an increase in oxidation state (loss of electrons).

Reduction is a decrease in oxidation state (gain of electrons).

1.4.4

Describe and explain galvanic cells in terms of oxidation/reduction reactions

A galvanic cell (electrochemical cell) is a device that allows electricity to be generated from a
spontaneous redox reaction.

It consists of two half-cells, each containing an electrode in an electrolyte solution. Oxidation

occurs in one half-cell and reduction in the other.

The electrodes are physically separated, but connected by an external circuit for the transfer of
electrons from the anode to the cathode. This flow of electrons produces electricity.

In any commercial galvanic cell, the two active chemicals must not be allowed to come into
contact, otherwise they would react directly and no electricity would be produced. The role of the
electrolyte in cells is to keep the active chemicals apart while allowing migration of ions through
the cell.

1.4.5

Outline the construction of galvanic cells and trace the direction of electron flow

1.4.6

Define the terms anode, cathode, electrode and electrolyte to describe galvanic cells
electron flow

anode

anions

external circuit

V
salt bridge

cations

cathode

(oxidation)

(reduction)

anolyte

catholyte

The anode is the electrode at which oxidation occurs.

The cathode is the electrode at which reduction occurs.
The electrodes are the conductors of the cell that get connected to the external circuit.
The electrolyte is the substance which in solution or molten conducts electricity (all salt solutions
are electrolytes).

The salt bridge is usually filter paper soaked in potassium nitrate,

and

do not

form any precipitates with other ions).

The purpose of the salt bridge is to facilitate the migration of ions from one half-cell to
another to complete the circuit and maintain electrical neutrality.

If the salt bridge is removed, the voltage falls to zero and no current flows.

15

Module 1 Production of Materials

A voltmeter can be used to measure the voltage (potential difference) between two half-cells. If
the voltmeter shows a positive voltage, it means the anode (where oxidation occurs) has the
greater ability to produce electrons.

As galvanic cell reactions proceed, there are several observations that can be made:

The size/mass of the anode decreases

Deposits of metal form on the cathode

The anolyte colour becomes darker and the catholyte colour fades

1.4.7

Solve problems and analyse information to calculate the potential

requirement of

named electrochemical processes using tables of standard potentials and half-equations

Standard reduction potential (

) is a measure of the relative tendency of a substance to

undergo reduction compared to the standard hydrogen electrode (0 ).

This is measured under standard laboratory conditions (SLC):

Temperature: 25 C;

Pressure: 100

Solution concentration: 1

The standard cell potential is the sum of the standard reduction potential and the standard
oxidation potential:

Note:

To obtain

, simply reverse the sign of the

Doubling the half-equation does not alter

A positive cell potential (

) indicates a spontaneous redox reaction will occur in the forward

direction.

The potential of a cell decreases as the reaction proceeds because the reactant is used up, so it
produces less current. Thus, batteries go flat when one of the reactants is all used up. No further
chemical reaction is possible so no more current is produced.

1.4.8

Gather and present information on the structure and chemistry of a lead-acid cell and

evaluate it in comparison to a vanadium redox cell in terms of chemistry, cost and practicality,
impact on society and environmental impact

Lead-acid cell:

In a lead-acid cell, six cells (each

) are

arranged in series to produce a

battery

(therefore, a battery is simply a series of

cells).

The lead-acid cell can be recharged by

application of an external current. This is
possible because the product of the
reaction (

) is insoluble and stays in

contact with the electrodes.

The battery is used during start-up to

v

g
g

. It is gradually recharged during driving using

.

16

Module 1 Production of Materials

Chemistry:

Anode:

Cathode:

Electrolyte:

( )

( )
( )

( )

()

Cost & Practicality:

The batteries are expensive due to the lead content.

The battery is reliable, long-lasting and can be recharged externally multiple times.

The batteries are bulky and heavy, limiting their portability.

They have the lowest energy density of most commonly used rechargeable batteries.

Impact on society:

The lead-acid battery is important for car start-up motors as it provides a large burst of
current to start an engine.

It is also a useful storage battery for remote locations and emergency lighting. It can be
recharged by connecting to solar panels or electric generators.

Environmental Impact:

Lead-acid batteries are recycled to retrieve the lead, as lead metal is a heavy metal that is
toxic to organisms in the environment and causes anaemia in humans.

The concentrated

electrolyte is highly acidic and can cause severe damage if

spilled. Sealed lead-acid cells prevent acid fumes from causing corrosion.

Vanadium redox cell:

A vanadium redox cell is a redox flow battery that consists of two vanadium electrolyte tanks
which are pumped through a battery stack, where the chemical energy stored in the solutions
is converted to electrical energy. The potential difference between the two half-cells leads to
electron flow in the external circuit.

The cell is recharged by passing an electric current through it and also by reversing the
solution flow, which reverses the two half-reactions.

The cell can also be recharged by replacing the spent electrolytes with fresh ones, since there
are no changes to electrodes during operation.

17

Module 1 Production of Materials

Chemistry:

Anode (graphite felt):

Cathode (graphite felt):

Anolyte:

Catholyte: (

(
(

)
(

()

solution
)

solution

Cost & Practicality:

There is a high cost to the vanadium redox cell until it is fully commercialised. However,
vanadium is a plentiful and hence cheap metal.

The battery is recharged at a low voltage but can deliver a high voltage on discharge.

It is important that the oxidant and reductant do not mix, which requires a separate
compartment for each solution, making it even less portable than the lead acid battery.

Impact on society: The vanadium redox cell has several important applications including:

Replacement for lead-acid batteries used to power up car motors, especially in remote
areas. This is important because lead-acid batteries face the environmental problem of
disposing toxic lead metal.

Power source for electric vehicles. Electric cars are increasingly being used as petrol
prices increase and supplies of petrol diminish in the near future.

Electrochemical storage of solar and wind energy. This is possible because the
vanadium battery can be recharged at low voltages, acting as an emergency backup
battery system.

Environmental Impact:

The vanadium redox cell may replace the lead-acid battery, hence avoiding the disposal of
toxic lead metal to the environment.

The vanadium solutions can be indefinitely recycled so it is safe and non-polluting, and
waste is minimised.

Comparison of the two cells:

Similarities

Both cells are rechargeable

Both have

in the electrolyte

Differences

The lead-acid cell consists of one compartment, whereas the vanadium redox cell has 2
compartments separated by a porous membrane.

Evaluation of the two cells:

Overall, the lead-acid battery delivers the required voltage but its use is disadvantaged by
lead which can pollute the environment.

The vanadium redox battery is safe and environmentally friendly but still in its developmental
stage.

18

Module 1 Production of Materials

1.4.9

Perform a first-hand investigation to identify the conditions under which a galvanic cell

is produced
1.4.10 Perform a first-hand investigation and gather first-hand information to measure the
difference in potential of different combinations of metals in an electrolyte solution

Aim: To find the order of the metals from the strongest to weakest reductant using galvanic cells.
Equipment: 150

beakers, strips of filter paper to make salt bridges, electrical leads with clips,

DC voltmeter, piece of emery paper, various electrodes and electrolytes.

Method:
1.

galvanic cell was set up. A

(

and a

electrode was placed in one beaker with

electrode in another beaker with

).

For each half-cell, the

electrodes were thoroughly cleaned with emery paper to remove corrosion and contaminants.
2.

The salt bridge was made from a strip of filter paper soaked in

solution. A clean strip of

filter paper was used for each cell to ensure that the ions in solution for the previous beaker
did not remain and react with the new ions (i.e. prevents possible precipitation).
3.

The potential difference was recorded for each cell.

4.

The

half-cell was used as a standard for comparing the other metal ion/metal half-

cells:

Results:

was found to be the strongest reductant and

.
was the strongest oxidant.

1.5

Nuclear Chemistry

1.5.1

Distinguish between stable and radioactive isotopes and describe the conditions under

which a nucleus is unstable

A radioactive isotope (radioisotope) has an unstable

nucleus which spontaneously emits radiation ( ,

or )

and undergoes a transmutation (change in composition).

A stable isotope does not emit radiation as it has a stable

nucleus.

An isotope is unstable (radioactive) if:

Atomic number is greater than 83 (

): These

isotopes undergo nuclear fission to form smaller, more

stable nuclei. An alpha decay results:

Ratio of neutrons to protons is outside the zone of

stability in a graph of no. of neutrons vs. no. of
protons.

20: stable

ratio is 1:1

50: stable

ratio is 1.3:1

80: stable

ratio is 1.5:1

High

ratio -

Low

Nucleus contains too much energy (i.e. metastable): It will undergo gamma emission.

ratio -

decay occurs
or

decay occurs

19

Module 1 Production of Materials

1.5.2

Describe how transuranic elements are produced

Transuranic elements are artificially produced elements with atomic numbers greater than that
of uranium (

92). Uranium has the largest value of the naturally occurring elements.

Transuranic elements are produced by bombardment of nuclei with neutrons or other nuclei, in
nuclear reactors or particle accelerators

Neutron bombardment:

Early transuranic elements were synthesised by neutron bombardment (supplied by a

nuclear reactor) of heavy elements.

Neptunium (

93) and plutonium (

94) can be synthesised in nuclear reactors by the

neutron bombardment of uranium-238. The unstable U-239 formed decays by beta

emission to form neptunium-239 and plutonium-239.

Fusion reactions:

The production of larger transuranic elements is achieved by bombarding heavy nuclei

with high speed positive particles (e.g. helium or carbon nuclei) produced in particle
accelerators, such as linear accelerators and cyclotrons.

Californium-246 is formed by bombarding uranium-238 with carbon in a linear

accelerator.
(

1.5.3

Describe how commercial radioisotopes are produced

Commercial radioisotopes are produced in nuclear reactors or particle accelerators.

Nuclear reactors supply neutrons which are bombarded at a target to produce neutron-rich
radioisotopes. Technetium-99m (medical radioisotope) is produced by neutron bombardment
of molybdenum-98.

Particle accelerators accelerate light positive particles to high speeds, which are then collided
with heavy nuclei. This produces neutron-deficient radioisotopes. Linear accelerators
accelerate particles in a straight line, while cyclotrons accelerate particles in a spiral path.
Fluorine-18 is prepared in a cyclotron by bombarding nitrogen-14 with helium nuclei.

1.5.4

Process information from secondary sources to describe recent discoveries of elements

Element 116, ununhexium (Uuh), was synthesised by Russian scientists in 2000 by bombarding
curium-248 with calcium-48.
(

Element 118, ununoctium (Uuo) is the most recently produced element, and the heaviest element
known to man. It was produced in 2002 by the fusion of californium-249 and calcium-48.
( )

20

Module 1 Production of Materials

1.5.5 Identify instruments and processes that can be used to detect radiation

Photographic film: (Note: this is not an instrument)

Radioactivity can be detected by the darkening of photographic film.

Radiation badges are worn by laboratory workers handling radioactive substances, and the
amount of darkening of the film is a measure of the amount of radiation that the worker has
received.

Cloud chamber:

A cloud chamber contains supersaturated water or alcohol vapour cooled with dry ice.

As radiation travels through their air and vapour, it ionises surrounding air molecules. The
vapour molecules condense onto these ions, creating small droplets or cloud trails that reveal
the path of the ionising radiation.
thinner zigzag tracks;

particles form straight dense tracks;

particles form

rays form even fainter tracks.

Scintillation counter:

When certain substances (e.g.

) are irradiated with ,

or

rays, they emit a flash of light

(scintillation) which can be collected and amplified in a photomultiplier. The electrical signal
generated is then counted electronically to measure the amount of radiation.

Geiger-Muller counter:

This device uses ionising properties of radiation, and is only able to measure

The

radiation.

ray enters the Geiger tube, collides with a gas molecule (e.g. argon) and ionises it,

knocking an electron out of it.

The high voltage accelerates this electron so that it ionises more argon atoms in its path,
constituting an electrical pulse which is amplified and measured by an amplifier or counter.

1.5.6

Identify one use of a named radioisotope in industry and in medicine

Industry: Cobalt-60 (Co-60) is used to irradiate food to prolong its shelf life.
Medicine: Technetium-99m (Tc-99m) is used in the diagnosis of disease.

1.5.7

Describe the way in which the above named industrial and medical radioisotopes are

used and explain their use in terms of their properties

Cobalt-60:

Use:

Co-60 is used to irradiate food materials to minimise spoilage and extend shelf life, and
sterilise medical supplies such as dressings and bandages. Food on a conveyor belt is
gamma irradiated by passing it through a chamber containing a safely shielded Co-60
source.

Properties:

Co-60 is chemically inert and is a potent gamma emitter. Gamma rays can easily
penetrate hermetically sealed packaging and the contents, killing harmful microbes such
as bacteria, viruses and fungi. They have sufficient energy to destroy bacteria but not
enough to make food radioactive.

Co-60 has a reasonably long half-life of 4-6 years, to minimise replacement.

However, there are concerns that gamma radiation can destroy vitamin content in food and
may lead to the formation of harmful compounds in the food. In addition, workers must be
protected from irradiation.

21

Module 1 Production of Materials

Technetium-99m:

Use:

Tc-99m is widely used for medical diagnosis. The Tc-99m is attached to a biological
molecule that concentrates in the organ to be investigated. A scintillation counter
measures the distribution of Tc-99m which can be used to detect and pinpoint blood
clots, constrictions and other circulation disorders.

Properties:

Tc-99m is particularly suitable for medical diagnosis due to its short half-life of 6 hours.
It rapidly decays and so causes minimal damage to the patient.

Tc-99m emits low energy gamma radiation, which causes minimal damage to healthy
cells, but can still be detected in the body by a gamma ray sensitive camera.

Tc-99m is quickly eliminated from the body.

Technetium is relatively reactive, so it can be reacted to form a compound with chemical

properties that leads to concentration in the organ of interest such as the heart, liver,
lungs or thyroid.

As Tc-99m has such a short half-life, it must be continuously made from the decay of
molybdemum-99.

1.5.8

Use available evidence to analyse benefits and problems associated with the use of

radioactive isotopes in identified industries and medicine

Benefits:

The main benefits of radioisotopes are largely in the field of medicine.

Radioisotopes have provided a range of non-invasive diagnostic techniques

Radiotherapy provides effective treatment of many cancerous tumours, especially in

sensitive organs (e.g. brain).

Radioisotopes also have the ability to:

Make monitoring equipment more sensitive and precise than earlier equipment.

Carry out tasks more efficiently and reliably (e.g. gamma ray sterilisation of medical
supplies, which is efficient and effective compared to other sterilisation methods).

Perform tasks that were not otherwise possible (e.g. examine buildings and machinery for
structural faults).

Problems:

Radiation from radioisotopes is harmful to humans and all other life forms. It can cause
undesirable reactions in living tissue and upset the delicate balance among the complex
chemical reactions occurring in living cells.

Continued exposure to radiation can lead to diseases such as tissue damage, cancer and
genetic damage (which leads to deformities in offspring). Workers who work with radioactive
elements must be continually protected and avoid any form of irradiation.

Nuclear reactors (the source of neutrons) produce nuclear waste which must be disposed of
safely. The storage of radioactive material also presents a problem, as it must be kept in
shielded containers to prevent radiation leaks.

22