FlowCon FAC6HP Instruction 04 2013

FlowCon FAC6HP
Commissioning meter
INSTALLATION AND OPERATION INSTRUCTION

FlowCon FAC6HP
Connect the FlowCon FAC6HP commissioning
meter to a valve by the following steps:
1. Ensure that the isolating valve on each tube is
closed and that the equalizing valve on the
side of the commissioning meter is fully open.
2. Connect each tube (recommended opposite
end of the isolating valves, though it does not
matter which end) with a p/t needle.
3. Remove metal protection caps on p/t needles.
4. Put the p/t needles into the p/t plugs on the
valve that is to be measured. (The red tube is
to be connected to the inlet side of the valve
and the blue tube with the outlet side)
5. Remove black plastic protection caps on
commissioning meter.
6. Attach the tubes to the commissioning meter.
(Matching the colors)
7. Open the isolating valves on the tubes. (This
will cause water to flow through the tubes and
commissioning meter and thus for a short
while bypassing the valve)
8. Close the isolating valves.
9. Press any button to turn on the commissioning
meter and then press the ZERO button on
the commissioning meter.
10. Open the isolating valves again.
11. Close the equalizing valve on the side of the
commissioning meter.
If the commissioning meter is subjected to extreme
temperature changes e.g. if transferred from a hot to
a cold system (or opposite) or if the commissioning
meter has been stored in a cold environment and
is used in a warm system (or opposite), it might be
necessary for the commissioning meter to stabilize
at the new temperature before zeroing (point 9 in
the above list). The time necessary to stabilize,
depend on the temperature difference.
Isolating valves
Commissioning meter
Tube
Equalizing valve
P/t needles
P/t plugs
Figure 1
To disconnect the commissioning meter follow

these steps:
1. Open the equalizing valve. (this will cause
water to flow through the tubes and commis sioning meter and thus for a short while by passing the valve)
2. Close the isolating valves.
3. If needed disconnect the tubes from the com missioning meter.
4. Remove the p/t needles from the p/t plugs on
the valve.
5. If needed disconnect the p/t needles from the
tubes.
6. When finished replace protection caps on both
p/t needles and commissioning meter.
Denmark
Dubai
USA
Brasil
Singapore
www.flowcon.com
1F9560004/2013
-1-
FlowCon International assumes no responsibility for mistakes, if any, in any printed material.
FlowCon FAC6HP
Main
Menus
Sub menus
Commissioning meter
display
units
advanced
damping
select valve
flow/pressure
pressure
flow alerts
up-date timee
valve position
multi dispaly
flow
black-light timer
sample time
design flow
pressure
auto-off timer
target flow
about
view size as?
pipe size
user kvs
change sg
Figure 2
Setting up.

Press any button to turn on the commissioning meter.

Press the MENU button once to enter the
menu or twice to choose a language (English,
French, Italian, Norwegian, Spanish, and
Swedish are available).
Navigate between the menus with and
and the sub menus with and . To choose
a sub menu use . Generally, is for entering sub menus, accepting values or choices,
while is for annulling and exiting menus.
For a full list of menus, please see figure 2.
Prior to use, please check the UNITS menu (

and to move between menus and to confirm) to ensure that the units on the commissioning meter match the units on the system or other
requirements.
Choose the valve by finding the MAIN menu
( and ) and the sub menu SELECT
VALVE ( and ), then press to confirm.
A new menu opens, please see figure 3.
FLOWCON
The lines in figure 3 are:

1. line: the manufacturer
2. line: valve series
3. line: valve name
4. line: valve size

To move between the lines use and . In

each line and can be used to change
the setting. To accept the valve, press .
To change the max. flow setting of the valve
(the default setting is the highest setting), go
to the MAIN menu and enter the VALVE
POSITION sub menu. Enter the setting digit
by digit (0- 9 and .).To leave the menu press .
Now the current differential pressure and flow
can be seen in the display (as shown in fig. 4).
Current flow
Nominal flow
352 l/h
FLOW
108.20
352.0 l/h
16.00
124.20 kPa
2.0
OK
Flowcon Green.0
Green
Green.0
Min. dP
Current dP
15-25mm
Figure 3
Verified flow
Setting
Current FlowCon valve
Figure 4
Denmark
Dubai
USA
Brasil
Singapore
www.flowcon.com
1F9560004/2013
-2-
FlowCon FAC6HP
Commissioning meter
To turn off the commissioning meter, please press

first (until prompted for shut-off), then . The
commissioning meter will by default shut off automatically after a period of inactivity specified
in the ADVANCED menu under the sub menu
AUTO-OFF TIMER.
Alerts.
Alerts are shown white on black in the upper left corner of the display. If several alerts are active, they
will be shown side-by-side if possible, but otherwise only a single alert will be visible at a time.
Memory.
By default the memory in the commissioning meter

holds 10 groups each with 10 valves spaces.
To access the memory, press . When the
memory is accessed, the colors on the screen
will be inverted (text is bright and background
is dark).
Navigate between the groups by pressing
and , and the valves within the current
groups by pressing and .
To save data, choose a valve and valve set ting the normal way and have the commission ing meter connected to the valve, then access
the memory, press MENU and then to
save the data.
If repeating the same measurements later, the
step of choosing each valve prior to access ing the memory can be skipped by accessing
the memory, and pressing MENU, then to
load the previously saved valve (including
valve setting) for that location. To save the new
data, access the memory and press MENU,
then to save the new data.
All data can be cleared from a valve by press ing MENU, then .
Alert
Icon/text
Explanation
Zeroing
ZERO DP
Zeroing is needed.
Please follow the list
of how to connect the
commissioning meter
to a valve, or repeat
steps 1 and 5-11.
Low battery
Battery level is low.
Change
battery
CHANGE
BATTERY
(whole
screen)
Battery level is critically

low. Please change
the battery.
Specific
gravity
SG
Specific gravity is not

set to 1.0 sg.
The commissioning
meter does not support
calculations with other
specific gravities than
1.0 sg for FlowCon
valves.
Temperature
warning
HIGH
TEMP
The internal temperature of the commissioning meter is high

(45C or above).
This results in poorer
accuracy.
If possible try to cool
it down.
Denmark
Dubai
USA
Brasil
Singapore
www.flowcon.com
1F9560004/2013
-3-
FlowCon FAC6HP
Commissioning meter
Changing battery.

To change the battery, first turn off the commissioning meter.

Then remove the lid from the lower part of the
back of the commissioning meter by unscrewing the two screws (the screw driver from
the carry case matches the screws) and lifting
the lid off.
Detach the two connectors from the old battery
and connect them to the new battery.
Put the lid back on and fasten the two screws.
The normal operating time for a standard
alkaline 9V 6LR61 battery is 20 hours.
Optional software.
For large systems or systems including FlowCon

wafers, the optional software for the commissioning
meter is recommended.
The software offers a possibility of setting up
valves consisting of multiple valve cartridges like
the FlowCon Wafers. A wafer includes a number
of Stainless Steel cartridges and its flow depends
solely on the characteristic of these cartridges.
Furthermore the software provides an option of
organizing the groups and valves in the memory
including custom naming and up to 2000 memory
locations in total.
General.
It is recommended flushing the system before

installing the insert in the valve body. Suitable
flushing caps are available. Water must always
be suitable treated, clean and free of debris. It is
recommended that a strainer be installed prior to
the valve body to prevent damage or blockage
due to debris. Ensure that the valve is not in the
fully closed position when filling the system with
water.
Warranty obligation.
Failure to abide by all recommendations as per

this installation and operation instruction will void
warranty.
For latest updates please see www.flowcon.com
Denmark
Dubai
USA
Brasil
Singapore
www.flowcon.com
1F9560004/2013
-4-

FlowCon FAC6HP Instruction 04 2013

Uploaded by

Copyright:

Available Formats

FlowCon FAC6HP Instruction 04 2013

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FlowCon FAC6HP Instruction 04 2013

Uploaded by

Copyright:

Available Formats

FlowCon FAC6HP

INSTALLATION AND OPERATION INSTRUCTION

To disconnect the commissioning meter follow

view size as?

Press any button to turn on the commissioning meter.

Prior to use, please check the UNITS menu (

The lines in figure 3 are:

To move between the lines use and . In

To turn off the commissioning meter, please press

By default the memory in the commissioning meter

Battery level is low.

Battery level is critically

Specific gravity is not

The internal temperature of the commissioning meter is high

To change the battery, first turn off the commissioning meter.

For large systems or systems including FlowCon

It is recommended flushing the system before

Failure to abide by all recommendations as per

You might also like