Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

6880309T86-C (Mototrbo Basico)

Download as pdf or txt
Download as pdf or txt
You are on page 1of 105

i

Foreword
This manual covers all DGM Series Mobiles, unless otherwise specified. It includes all the information necessary to
maintain peak product performance and maximum working time, using levels 1 and 2 maintenance procedures. This level
of service goes down to the board replacement level and is typical of some local service centers, Motorola Authorized
Dealers, self-maintained customers, and distributors.

!
Caution

These servicing instructions are for use by qualified personnel only. To


reduce the risk of electric shock, do not perform any servicing other than
that contained in the Operating Instructions unless you are qualified to do
so. Refer all servicing to qualified service personnel.

Product Safety and RF Exposure Compliance

!
Caution

Before using this product, read the operating instructions for safe usage
contained in the Product Safety and RF Exposure booklet enclosed with
your radio.
ATTENTION!

This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy awareness information and operating instructions in
the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part
number 6881095C99) to ensure compliance with RF energy exposure limits.
For a list of Motorola-approved antennas, and other accessories, visit the following web site which
lists approved accessories: http://www.motorola.com/governmentandenterprise

Computer Software Copyrights


The Motorola products described in this manual may include copyrighted Motorola computer programs stored in
semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain
exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce
in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in
the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or
distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola
products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by
operation of law in the sale of a product.

Document Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express written
permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any
means, electronic or mechanical, for any purpose without the express written permission of Motorola.

Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is
assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve
readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product
or circuit described herein; nor does it cover any license under its patent rights nor the rights of others.

Trademarks
MOTOROLA and the Stylized M logo are registered in the U.S. Patent & Trademark Office. All other product or service
names are the property of their respective owners.
2007 by Motorola, Inc.
All rights reserved.
6880309T86-C

November 14, 2007

ii

Notes

November 14, 2007

6880309T86-C

iii

Document History
The following major changes have been implemented in this manual since the previous edition.
Edition

Description

Date

6880309T86-A

Initial Release.

July. 2007

6880309T86-B

Added VHF Low Power Band and Numeric


Display models to VHF High Power Band.
Updated GPS model names.

Oct. 2007

6880309T86-C

Added Option Board Information and Power


Cable HKN4191_.

Nov. 2007

6880309T86-C

November 14, 2007

iv

Notes

November 14, 2007

6880309T86-C

Table of Contents

Table of Contents
Foreword ..........................................................................................................i
Product Safety and RF Exposure Compliance .............................................................................................i
Computer Software Copyrights ....................................................................................................................i
Document Copyrights ...................................................................................................................................i
Disclaimer.....................................................................................................................................................i
Trademarks ..................................................................................................................................................i

Document History ........................................................................................ iii


Commercial Warranty ..................................................................................xii
Limited Warranty ....................................................................................................................................... xii
MOTOROLA COMMUNICATION PRODUCTS ............................................................................. xii
I. What This Warranty Covers And For How Long .................................................................... xii
II. General Provisions ................................................................................................................ xii
III. State Law Rights (Applicable Only in U.S.A.)...................................................................... xiii
IV. How To Get Warranty Service ............................................................................................ xiii
V. What This Warranty Does Not Cover................................................................................... xiii
VI. Patent And Software Provisions ......................................................................................... xiv
VII. Governing Law................................................................................................................... xiv

Chapter 1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9

Notations Used in This Manual .................................................................................................... 1-1


Radio Description ........................................................................................................................ 1-1
Control Head Description............................................................................................................. 1-2
1.3.1 Control Head Controls (Display Model) ........................................................................... 1-2
1.3.2 Control Head Controls (Numeric Display Model)............................................................. 1-3
MOTOTRBO Mobile Radio Model Numbering Scheme............................................................... 1-4
VHF High Power (136-174 MHz) Model Chart ........................................................................... 1-5
VHF Low Power (136-174 MHz) Model Chart ........................................................................... 1-5
UHF1 High Power (403-470 MHz) Model Chart ........................................................................ 1-6
UHF1 Low Power (403-470 MHz) Model Chart .......................................................................... 1-6
Specifications............................................................................................................................... 1-7

Chapter 2
2.1
2.2
2.3

Introduction ......................................................................... 1-1

Test Equipment and Service Aids ..................................... 2-1

Recommended Test Equipment .................................................................................................. 2-1


Service Aids ................................................................................................................................. 2-2
Programming Cables ................................................................................................................... 2-2

6880309T86-C

November 14, 2007

vi

Table of Contents

Chapter 3
3.1
3.2
3.3

3.4

General ........................................................................................................................................ 3-1


Setup............................................................................................................................................ 3-1
Display Model Test Mode ............................................................................................................ 3-2
3.3.1 Entering Display Radio Test Mode .................................................................................. 3-2
3.3.2 RF Test Mode .................................................................................................................. 3-2
3.3.3 Display Test Mode ........................................................................................................... 3-3
3.3.4 LED Test Mode................................................................................................................ 3-3
3.3.5 Backlight Test Mode ........................................................................................................ 3-3
3.3.6 Speaker Tone Test Mode ................................................................................................ 3-3
3.3.7 Earpiece Tone Test Mode ............................................................................................... 3-3
3.3.8 Audio Loopback Test Mode ............................................................................................. 3-3
3.3.9 Audio Loopback Earpiece Test Mode.............................................................................. 3-4
3.3.10 Button/Knob/PTT Test Mode ........................................................................................... 3-4
Numeric Display Model Test Mode .............................................................................................. 3-4
3.4.1 Entering Display Radio Test Mode .................................................................................. 3-4
3.4.2 RF Test Mode .................................................................................................................. 3-4
3.4.3 Display Test Mode ........................................................................................................... 3-4
3.4.4 LED Test Mode................................................................................................................ 3-5
3.4.5 Speaker Tone Test Mode ................................................................................................ 3-5
3.4.6 Earpiece Tone Test Mode ............................................................................................... 3-5
3.4.7 Audio Loopback Test Mode ............................................................................................. 3-5
3.4.8 Audio Loopback Earpiece Test Mode.............................................................................. 3-5
3.4.9 Button/Knob/PTT Test Mode ........................................................................................... 3-5

Chapter 4
4.1
4.2
4.3
4.4

5.3
5.4
5.5
5.6

Radio Programming and Tuning ....................................... 4-1

Introduction .................................................................................................................................. 4-1


Customer Programming Software Setup ..................................................................................... 4-1
AirTracer Application Tool............................................................................................................ 4-2
Radio Tuning Setup ..................................................................................................................... 4-3

Chapter 5
5.1
5.2

Transceiver Performance Testing ..................................... 3-1

Disassembly/Reassembly Procedures ............................. 5-1

Introduction .................................................................................................................................. 5-1


Preventive Maintenance .............................................................................................................. 5-1
5.2.1 Inspection ........................................................................................................................ 5-1
5.2.2 Cleaning Procedures ....................................................................................................... 5-1
Safe Handling of CMOS and LDMOS Devices ............................................................................ 5-2
Repair Procedures and Techniques General .......................................................................... 5-4
Disassembling and Reassembling the Radio General ............................................................ 5-5
Radio Disassembly Detailed ................................................................................................... 5-5
5.6.1 Control Head Removal .................................................................................................... 5-5
5.6.2 Top Cover Removal......................................................................................................... 5-6
5.6.3 Transceiver Board Removal ............................................................................................ 5-7
5.6.4 GPS Antenna Connector Removal (For GPS models only) .......................................... 5-10
5.6.5 Disassembly of Display Model Control Head................................................................. 5-10
5.6.6 Disassembly of Numeric Display Model Control Head .................................................. 5-12
5.6.7 Option Board Module Removal...................................................................................... 5-15

November 14, 2007

6880309T86-C

Table of Contents

5.7

5.8
5.9

Radio Reassembly Detailed .................................................................................................. 5-16


5.7.1 Display Model Control Head.......................................................................................... 5-16
5.7.2 Numeric Display Model Control Head ........................................................................... 5-21
5.7.3 Radio Assembly............................................................................................................. 5-28
5.7.4 GPS Plug or GPS Antenna Connector Reassembly ..................................................... 5-29
5.7.5 Transceiver Board Reassembly .................................................................................... 5-30
5.7.6 Thermal Pad Replacement Procedure .......................................................................... 5-36
5.7.7 Assemble Control Head and Decorative Cover to Radio Assembly.............................. 5-38
5.7.8 Option Board Module Reassembly................................................................................ 5-39
Exploded Mechanical Views and Parts Lists ............................................................................. 5-41
5.8.1 Radio Assembly Exploded View and Parts List............................................................. 5-41
5.8.2 Control Head Exploded Views and Parts Lists .............................................................. 5-43
Torque Chart.............................................................................................................................. 5-45

Chapter 6
6.1
6.2
6.3
6.4

Basic Troubleshooting ....................................................... 6-1

Introduction .................................................................................................................................. 6-1


6.1.1 High Power RF Precaution .............................................................................................. 6-1
Replacement Service Kit Procedures .......................................................................................... 6-1
Power-Up Error Codes ................................................................................................................ 6-2
Operational Error Codes .............................................................................................................. 6-3

Chapter 7
7.1

vii

Accessories ......................................................................... 7-1

Introduction .................................................................................................................................. 7-1


7.1.1 Audio ............................................................................................................................... 7-1
7.1.2 Speakers ......................................................................................................................... 7-1
7.1.3 Desktop Accessories ....................................................................................................... 7-1
7.1.4 Mounting Kits................................................................................................................... 7-2
7.1.5 Cables ............................................................................................................................. 7-2
7.1.6 Antennas ......................................................................................................................... 7-2
7.1.7 Miscellaneous Accessories ............................................................................................. 7-4
7.1.8 Replacement Button Parts and Kits................................................................................. 7-4

Appendix A Replacement Parts Ordering..............................................A-1


A.1
A.2

Basic Ordering Information ..........................................................................................................A-1


Motorola Online ...........................................................................................................................A-1

Appendix B Motorola Service Centers...................................................B-1


B.1
B.2
B.3

Servicing Information ...................................................................................................................B-1


Motorola de Mxico, S.A..............................................................................................................B-1
Motorola de Colombia, Ltd...........................................................................................................B-1

Glossary ......................................................................................... Glossary-1

6880309T86-C

November 14, 2007

viii

List of Figures

List of Figures
Figure 1-1
Figure 1-2
Figure 1-3
Figure 2-1
Figure 2-2
Figure 2-3
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
Figure 5-5
Figure 5-6
Figure 5-7
Figure 5-8
Figure 5-9
Figure 5-10
Figure 5-11
Figure 5-12
Figure 5-13
Figure 5-14
Figure 5-15
Figure 5-16
Figure 5-17
Figure 5-18
Figure 5-19
Figure 5-20
Figure 5-21
Figure 5-22
Figure 5-23
Figure 5-24
Figure 5-25
Figure 5-26
Figure 5-27
Figure 5-28
Figure 5-29
Figure 5-30
Figure 5-31
Figure 5-32
Figure 5-33
Figure 5-34
Figure 5-35
Figure 5-36
Figure 5-37
Figure 5-38
Figure 5-39
Figure 5-40

Radio Control Head (Display Model).................................................................................... 1-2


Radio Control Head (Numeric Display Model) ..................................................................... 1-3
Mobile Radio Model Numbering Scheme............................................................................. 1-4
Mobile Front Programming Cable HKN6184_...................................................................... 2-2
Mobile & Repeater Rear Programming Cable PMKN4010_ ................................................ 2-3
Mobile & Repeater Rear Accessory Programming and Test Cable PMKN4016_ ................ 2-3
Customer Programming Software Setup from Front Connector .......................................... 4-1
Customer Programming Software Setup from Rear Accessory Connector ......................... 4-2
Customer Programming Software Setup with Test Box Connection .................................... 4-2
Radio Tuning Equipment Setup ........................................................................................... 4-3
Typical Control Head Removal............................................................................................. 5-5
Flexible Connection Removal .............................................................................................. 5-6
Top Cover Removal.............................................................................................................. 5-6
Die Cast Cover Removal...................................................................................................... 5-7
Rear Accessory Connector Removal ................................................................................... 5-8
RF/DC Retention Clips Removal.......................................................................................... 5-8
GPS Cable Removal ............................................................................................................ 5-9
Transceiver Board Removal................................................................................................. 5-9
LCD Display Flex Removal ................................................................................................ 5-10
Left and Right Arrow Key Removal .................................................................................... 5-10
Control Head Board Removal ............................................................................................ 5-11
Keypad Removal ................................................................................................................ 5-11
Volume Knob Removal....................................................................................................... 5-12
Control Head Board Removal ............................................................................................ 5-12
Icon Light Guide Removal .................................................................................................. 5-13
Keypad Removal ................................................................................................................ 5-13
Icon Light Guide Holder Removal ...................................................................................... 5-14
Speaker and Volume Knob Removal ................................................................................. 5-14
Removing Option Flex from Option Board ......................................................................... 5-15
Removing Option Board from Radio Assembly.................................................................. 5-15
LCD Display Placement ..................................................................................................... 5-16
Keypad Assembly............................................................................................................... 5-17
Light Guide Assembly ........................................................................................................ 5-17
Assembling Mic Jack Seal ................................................................................................. 5-18
Assembling Board to Control Head Assembly ................................................................... 5-18
Screw Sequence ................................................................................................................ 5-19
Speaker Assembly ............................................................................................................. 5-19
Speaker Retainer Assembly ............................................................................................... 5-19
Left and Right Arrow Key Assembly................................................................................... 5-20
Flex Cable Assembly ......................................................................................................... 5-20
Volume Knob Assembly ..................................................................................................... 5-21
Icon Light Guide Holder Assembly ..................................................................................... 5-21
Keypad Assembly............................................................................................................... 5-22
Icon Light Guide Assembly ................................................................................................ 5-22
Light Guide and Light Guide Holder Assembly .................................................................. 5-23
Mic Jack Seal Assembly .................................................................................................... 5-23
LED Display Assembly ....................................................................................................... 5-24
Printed Circuit Board Assembly ......................................................................................... 5-24
Screw Sequence ................................................................................................................ 5-25
Speaker Assembly ............................................................................................................. 5-25

November 14, 2007

6880309T86-C

List of Figures

ix

Figure 5-41
Figure 5-42
Figure 5-43
Figure 5-44
Figure 5-45
Figure 5-46
Figure 5-47
Figure 5-48
Figure 5-49
Figure 5-50
Figure 5-51
Figure 5-52
Figure 5-53
Figure 5-54
Figure 5-55
Figure 5-56
Figure 5-57
Figure 5-58
Figure 5-59
Figure 5-60
Figure 5-61
Figure 5-62
Figure 5-63
Figure 5-64
Figure 5-65
Figure 5-66
Figure 5-67
Figure 5-68

Speaker Retainer Assembly............................................................................................... 5-26


Flex Cable Assembly ......................................................................................................... 5-26
Volume Knob Assembly ..................................................................................................... 5-27
Thermal Pads and Shield Gasketing on Chassis and Die Cast Cover .............................. 5-28
Transceiver Board with Thermal Pad ................................................................................. 5-28
GPS Plug Assembly........................................................................................................... 5-29
Bend in the GPS Antenna Connector ................................................................................ 5-29
GPS Antenna Connector Assembly ................................................................................... 5-30
Placing the Transceiver Board in the Chassis ................................................................... 5-30
Routing GPS Connector on to Transceiver Board ............................................................. 5-31
Inserting RF/DC Retention Clips ........................................................................................ 5-32
Inserting Rear Accessory Connector ................................................................................. 5-32
Assembling of VHF PA Heat Sink System ......................................................................... 5-33
Assembling of PA Pad and O-ring (UHF models) .............................................................. 5-34
Assembling of PA Pad and O-ring (VHF models) .............................................................. 5-34
Assembling Die Cast Cover onto Chassis ......................................................................... 5-35
Screw Sequence to Tighten Die Cast Cover...................................................................... 5-36
Replacing Thermal Pads.................................................................................................... 5-36
Aligning Driver Pad on Chassis.......................................................................................... 5-37
Placing Thermal Pads on PA and Transistor Components ................................................ 5-37
Mic Jack Pad and Speaker Pad on Chassis ...................................................................... 5-38
Folding Option Flex ............................................................................................................ 5-39
Assembling Option Board to Radio Chassis ...................................................................... 5-39
Assembling Option Flex to Option Board ........................................................................... 5-40
Inserting Option Flex End .................................................................................................. 5-40
Radio Assembly Exploded View ........................................................................................ 5-41
Display Control Head Exploded View ................................................................................ 5-43
Numeric Display Control Head Exploded View .................................................................. 5-44

6880309T86-C

November 14, 2007

List of Tables

List of Tables
Table 1-1
Table 2-1
Table 2-2
Table 3-1
Table 3-2
Table 3-3
Table 3-4
Table 3-5
Table 3-6
Table 3-7
Table 4-1
Table 5-1
Table 5-2
Table 5-3
Table 5-4
Table 5-5
Table 5-6
Table 6-1
Table 6-2

Radio Frequency Ranges and Power Levels ....................................................................... 1-1


Recommended Test Equipment ........................................................................................... 2-1
Service Aids ......................................................................................................................... 2-2
Initial Equipment Control Settings ........................................................................................ 3-1
Front Panel Access Test Mode Displays .............................................................................. 3-2
Test Environments................................................................................................................ 3-5
Test Channel Spacing .......................................................................................................... 3-6
Test Frequencies .................................................................................................................. 3-6
Transmitter Performance Checks......................................................................................... 3-7
Receiver Performance Checks ............................................................................................ 3-8
Radio Software Program Kit................................................................................................. 4-1
Lead Free Solder Wire Part Number List ............................................................................. 5-4
Lead Free Solder Paste Part Number List ........................................................................... 5-4
Radio Exploded View Parts List ......................................................................................... 5-42
Display Control Head (PMLN4759_) Exploded View Parts List ......................................... 5-43
Numeric Display Control Head (PMLN4967_) Exploded View Parts List........................... 5-44
Torque Specifications for Nuts and Screws ........................................................................ 5-45
Power-Up Error Codes ......................................................................................................... 6-2
Operational Error Codes ...................................................................................................... 6-3

November 14, 2007

6880309T86-C

Related Publications

xi

Related Publications
*MOTOTRBO User Guide CD ..................................................................................................... HKLN4344_

6880309T86-C

November 14, 2007

xii

Commercial Warranty

Commercial Warranty

Limited Warranty
MOTOROLA COMMUNICATION PRODUCTS
I. What This Warranty Covers And For How Long
MOTOROLA INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication
Products listed below (Product) against defects in material and workmanship under normal use and
service for a period of time from the date of purchase as scheduled below:

DGM Series Digital Mobile Radios

Two (2) Years

Product Accessories

One (1) Year

Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts),
replace it (with a new or reconditioned Product), or refund the purchase price of the Product during
the warranty period provided it is returned in accordance with the terms of this warranty. Replaced
parts or boards are warranted for the balance of the original applicable warranty period. All replaced
parts of Product shall become the property of MOTOROLA.
This express limited warranty is extended by MOTOROLA to the original end user purchaser only
and is not assignable or transferable to any other party. This is the complete warranty for the Product
manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or
modifications to this warranty unless made in writing and signed by an officer of MOTOROLA.
Unless made in a separate agreement between MOTOROLA and the original end user purchaser,
MOTOROLA does not warrant the installation, maintenance or service of the Product.
MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by
MOTOROLA which is attached to or used in connection with the Product, or for operation of the
Product with any ancillary equipment, and all such equipment is expressly excluded from this
warranty. Because each system which may use the Product is unique, MOTOROLA disclaims
liability for range, coverage, or operation of the system as a whole under this warranty.

II. General Provisions


This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product.
Repair, replacement or refund of the purchase price, at MOTOROLA's option, is the exclusive
remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF
USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS
OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE
DISCLAIMED BY LAW.

November 14, 2007

6880309T86-C

Commercial Warranty

xiii

III. State Law Rights (Applicable Only in U.S.A.)


SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY.
This warranty gives specific legal rights, and there may be other rights which may vary from state to
state.

IV. How To Get Warranty Service


You must provide proof of purchase (bearing the date of purchase and Product item serial number)
in order to receive warranty service and, also, deliver or send the Product item, transportation and
insurance prepaid, to an authorized warranty service location. Warranty service will be provided by
Motorola through one of its authorized warranty service locations. If you first contact the company
which sold you the Product, it can facilitate your obtaining warranty service. You can also open a
Contact Us case on Motorola Online (www.motorola.com/businessonline).

V. What This Warranty Does Not Cover


A. Defects or damage resulting from use of the Product in other than its normal and customary
manner.
B. Defects or damage from misuse, accident, water, or neglect.
C. Defects or damage from improper testing, operation, maintenance, installation, alteration,
modification, or adjustment.
D. Breakage or damage to antennas unless caused directly by defects in material workmanship.
E. A Product subjected to unauthorized Product modifications, disassemblies or repairs
(including, without limitation, the addition to the Product of non-Motorola supplied equipment)
which adversely affect performance of the Product or interfere with Motorola's normal
warranty inspection and testing of the Product to verify any warranty claim.
F.

Product which has had the serial number removed or made illegible.

G. Freight costs to the repair depot.


H. A Product which, due to illegal or unauthorized alteration of the software/firmware in the
Product, does not function in accordance with MOTOROLAs published specifications or the
FCC type acceptance labeling in effect for the Product at the time the Product was initially
distributed from MOTOROLA.
I.

Scratches or other cosmetic damage to Product surfaces that does not affect the operation of
the Product.

J.

Normal and customary wear and tear.

6880309T86-C

November 14, 2007

xiv

Commercial Warranty

VI. Patent And Software Provisions


MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the
extent that it is based on a claim that the Product or parts infringe a United States patent, and
MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in
any such suit which are attributable to any such claim, but such defense and payments are
conditioned on the following:
A. that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such
claim;
B. that MOTOROLA will have sole control of the defense of such suit and all negotiations for its
settlement or compromise; and
C. should the Product or parts become, or in MOTOROLA's opinion be likely to become, the
subject of a claim of infringement of a United States patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure for such purchaser the right to
continue using the Product or parts or to replace or modify the same so that it becomes
noninfringing or to grant such purchaser a credit for the Product or parts as depreciated and
accept its return. The depreciation will be an equal amount per year over the lifetime of the
Product or parts as established by MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent infringement which is based
upon the combination of the Product or parts furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary
equipment or software not furnished by MOTOROLA which is attached to or used in connection with
the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of
patents by the Product or any parts thereof.
Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for
copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute
copies of such Motorola software. MOTOROLA software may be used in only the Product in which
the software was originally embodied and such software in such Product may not be replaced,
copied, distributed, modified in any way, or used to produce any derivative thereof. No other use
including, without limitation, alteration, modification, reproduction, distribution, or reverse
engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is
permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent
rights or copyrights.

VII. Governing Law


This Warranty is governed by the laws of the State of Illinois, USA.

November 14, 2007

6880309T86-C

Chapter 1 Introduction

1.1

Notations Used in This Manual


Throughout the text in this publication, you will notice the use of note and caution notations. These
notations are used to emphasize that safety hazards exist, and due care must be taken and
observed.
NOTE: An operational procedure, practice, or condition that is essential to emphasize.

CAUTION indicates a potentially hazardous situation which, if


not avoided, might result in equipment damage.

Caution

1.2

Radio Description
The DGM series mobile radios are available in the following frequency ranges and power levels.
Table 1-1 Radio Frequency Ranges and Power Levels
Freq. Band

Bandwidth

Power Level

VHF

136-174 MHz

1-25 Watts
25-45 Watts

UHF B1

403470 MHz

1-25 Watts
25-40 Watts

These digital radios are among the most sophisticated two-way radios available. They have a
robust design for radio users who need high performance, quality, and reliability in their daily
communications. This architecture provides the capability of supporting a multitude of legacy and
advanced features resulting in a more cost-effective two-way radio communications solution.

1-2

Introduction: Control Head Description

1.3

Control Head Description


The control head used with the radio has logic circuitry that operates the standard and optional
features built into the system.
The following illustrations show the typical radio control heads.

Power Button
LED
Indicators

Volume Knob

Mic Connector

LCD Screen

Channel Rocker

Menu Buttons

Speaker

Programmable Buttons

Figure 1-1 Radio Control Head (Display Model)

1.3.1

Control Head Controls (Display Model)


POWER BUTTON - Turns the radio on and off.
VOLUME KNOB - Rotate clockwise to increase volume level; rotate counter-clockwise to
decrease volume level.
LED INDICATORS - Red, yellow and green light-emitting diodes indicate operating status.
LCD (Liquid Crystal Display) - 132x34 full dot matrix display provides visual information about
many radio features.
MENU OPERATION BUTTONS - Five buttons to provide menu navigation and selection
interface.
PROGRAMMABLE BUTTONS - Four buttons are field programmable using the CPS.
CHANNEL CHANGING ROCKER - Press top side to increment or bottom side to decrement
the channel.

November 14, 2007

6880309T86-C

Introduction: Control Head Description

1-3

LED Numeric Display


Power Button
LED
Indicators

Channel Rocker

Volume Knob

Mic Connector

Indicator Icons

Speaker
Programmable Buttons

Figure 1-2 Radio Control Head (Numeric Display Model)

1.3.2

Control Head Controls (Numeric Display Model)


POWER BUTTON - Turns the radio on and off.
VOLUME KNOB - Rotate clockwise to increase volume level; rotate counter-clockwise to
decrease volume level.
LED INDICATORS - Red, yellow and green light-emitting diodes indicate operating status.
LED NUMERIC DISPLAY - Two digit numeric display.
PROGRAMMABLE BUTTONS - Two buttons are field programmable using the CPS.
CHANNEL CHANGING ROCKER - Press top side to increment or bottom side to decrement
the channel.
INDICATOR ICONS - Indicates status of various functions including private call, talkaround and
scan.

6880309T86-C

November 14, 2007

1-4

1.4

Introduction: MOTOTRBO Mobile Radio Model Numbering Scheme

MOTOTRBO Mobile Radio Model Numbering Scheme

Model No.Example :
Position

AA

10

11

12
Unique Model Variations
N: Standard Package

AZ: Asia/Australia
LA: Latin America
AA: North America (except Mexico)
MD: Europe/Middle East/Africa

Version Letter

Mobile

MOTOTRBO Mobile
Model Series

Feature Level
1: Mini-U
2: BNC

Band
J : 136-174 MHz
Q: 403-470 MHz
Primary System Type
A: Conventional
Power Level
N: 1-25W
P: 25-40W
Q: 25-45W

Physical Packages
C: Numeric Display Model
H: Display Model

Primary Operation
J: w/o GPS
L: w/ GPS

Channel Spacing
9: Variable/Programmable

Figure 1-3 Mobile Radio Model Numbering Scheme

November 14, 2007

6880309T86-C

Introduction: VHF High Power (136-174 MHz) Model Chart

1.5

1-5

VHF High Power (136-174 MHz) Model Chart


VHF 136-174 MHz 25-45W, Mini-U
Model

LAM27JQC9JA1AN
LAM27JQC9LA1AN
LAM27JQH9JA1AN
LAM27JQH9LA1AN

Description
136-174 MHz, 25-45W, MOTOTRBO DGM 4100 Numeric Display Mobile
136-174 MHz, 25-45W, MOTOTRBO DGM 4100+ Numeric Display Mobile
with GPS
136-174 MHz, 25-45W, MOTOTRBO DGM 6100 Display Mobile
136-174 MHz, 25-45W, MOTOTRBO DGM 6100+ Display Mobile with GPS

Item
X

X
X

X X

PMUD2044_S

Description
*Service Kit, VHF, 25-45W

X PMUD2043_S

*Service Kit, VHF, 25-45W, with GPS

PMLN4967_

Numeric Display Model Control Head

X X PMLN4759_
X X X X HKLN4344_

Display Model Control Head


User Guide CD

* = Service Kit is the main board only


X = Item Included
_ = the latest version kit. When ordering a kit, refer to your specific kit for the suffix number.

1.6

VHF Low Power (136-174 MHz) Model Chart


VHF 136-174 MHz 1-25W, Mini-U
Model

LAM27JNC9JA1AN
LAM27JNC9LA1AN
LAM27JNH9JA1AN
LAM27JNH9LA1AN

Description
136-174 MHz, 1-25W, MOTOTRBO DGM 4100 Numeric Display Mobile
136-174 MHz, 1-25W, MOTOTRBO DGM 4100+ Numeric Display Mobile
with GPS
136-174 MHz, 1-25W, MOTOTRBO DGM 6100 Display Mobile
136-174 MHz, 1-25W, MOTOTRBO DGM 6100+ Display Mobile with GPS

Item
X

X
X

X X

PMUD2040_S
X PMUD2039_S
PMLN4967_

X X PMLN4759_
X X X X HKLN4344_

Description
*Service Kit, VHF, 1-25W
*Service Kit, VHF, 1-25W, with GPS
Numeric Display Model Control Head
Display Model Control Head
User Guide CD

* = Service Kit is the main board only


X = Item Included
_ = the latest version kit. When ordering a kit, refer to your specific kit for the suffix number.

6880309T86-C

November 14, 2007

1-6

Introduction: UHF1 High Power (403-470 MHz) Model Chart

1.7

UHF1 High Power (403-470 MHz) Model Chart


UHF1 403-470 MHz 25-40W, Mini-U
Model

Description

LAM27QPC9JA1AN

403-470 MHz, 25-40W, MOTOTRBO DGM 4100 Numeric Display Mobile

LAM27QPC9LA1AN

403-470 MHz, 25-40W, MOTOTRBO DGM 4100+ Numeric Display Mobile,


with GPS

LAM27QPH9JA1AN

403-470 MHz, 25-40W, MOTOTRBO DGM 6100 Display Mobile

LAM27QPH9LA1AN 403-470 MHz, 25-40W, MOTOTRBO DGM 6100+ Display Mobile, with GPS

Item
X

X
X

Description

PMUE2346_S

*Service Kit, UHF B1, 25-40W

X PMUE2345_S

X X

*Service Kit, UHF B1, 25-40W, with GPS

PMLN4967_

Numeric Display Model Control Head

X X PMLN4759_

Display Model Control Head

X X X X HKLN4344_

User Guide CD

* = Service Kit is the main board only


X = Item Included
_ = the latest version kit. When ordering a kit, refer to your specific kit for the suffix number.

1.8

UHF1 Low Power (403-470 MHz) Model Chart


UHF1 403-470 MHz 1-25W, Mini-U
Model

LAM27QNC9JA1AN
LAM27QNC9LA1AN
LAM27QNH9JA1AN
LAM27QNH9LA1AN

Description
403-470 MHz, 1-25W, MOTOTRBO DGM 4100 Numeric Display Mobile
403-470 MHz, 1-25W, MOTOTRBO DGM 4100+ Numeric Display Mobile,
with GPS
403-470 MHz, 1-25W, MOTOTRBO DGM 6100 Display Mobile
403-470 MHz, 1-25W, MOTOTRBO DGM 6100+ Display Mobile, with GPS

Item
X

X
X

X X

PMUE2342_S
X PMUE2341_S
PMLN4967_

X X PMLN4759_
X X X X HKLN4344_

Description
*Service Kit, UHF B1, 1-25W
*Service Kit, UHF B1, 1-25W, with GPS
Numeric Display Model Control Head
Display Model Control Head
User Guide CD

* = Service Kit is the main board only


X = Item Included
_ = the latest version kit. When ordering a kit, refer to your specific kit for the suffix number.

November 14, 2007

6880309T86-C

Introduction: Specifications

1.9

1-7

Specifications
General
Specification

VHF
Numeric Display
Model

Channel Capacity

UHF1
Display Model

32

Display Model

Numeric Display
Model

160

32

Typical RF Output
Low Power
High Power

1-25 W
25-45 W

1-25 W
25-40 W

Frequency Range:

136-174 MHz

403-470 MHz

Dimensions (HxWxL)
Weight
Current Drain:
Standby
Rx @ rated audio
Transmit

FCC Description
IC Description

6880309T86-C

2.01 x 6.89 x 8.11 in


(51 x 175 x 206 mm)
4.0 lbs. (1.8 kg)
0.81 A max
2 A max
1-25 W: 11.0 A max
25-40 W: 14.5 A max
25-45 W: 14.5 A max
1-25 W: ABZ99FT3083
25-45 W: ABZ99FT3082

1-25 W: ABZ99FT4081
25-40 W: ABZ99FT4080

1-25 W: 109AB-99FT3083
25-45 W: 109AB-99FT3082

1-25 W: 109AB-99FT4081
25-40 W: 109AB-99FT4080

November 14, 2007

1-8

Introduction: Specifications

Receiver
Specification

VHF

UHF1

Numeric Display Display Model Display Model Numeric Display


Model
Model
Frequencies

136-174 MHz

Channel Spacing
Frequency Stability
(-30C to +60C)

403-470 MHz
12.5 kHz/25 kHz

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

Analog Sensitivity (12 dB


Sinad)

0.3 V
0.22 V (typical)

Digital Sensitivity

5% BER: 0.3 V

Intermodulation (TIA603C)
Adjacent Channel Selectivity
TIA603
TIA603C
Spurious Rejection
(TIA603C)
Rated Audio

Audio Distortion @ Rated


Audio

78 dB

75 dB

65 dB @12.5 kHz,
80 dB @ 25 kHz
50 dB @ 12.5 kHz,
80 dB @ 25 kHz

65 dB @12.5 kHz,
75 dB @ 25 kHz
50 dB @ 12.5 kHz,
75 dB @ 25 kHz

80 dB

75 dB
3 W (Internal)
7.5 W (External - 8 ohms)
13 W (External - 4 ohms)
3% (Typical)

Hum and Noise

-40 dB @ 12.5 kHz


-45 dB @ 25 kHz

Audio Response

TIA603C

Conducted Spurious
Emission (TIA603C)

-57 dBm

November 14, 2007

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

6880309T86-C

Introduction: Specifications

1-9

Transmitter
Specification

VHF
Numeric Display
Model

Frequencies

UHF1
Display Model

Display Model

136-174 MHz

Numeric Display
Model

403-470 MHz

Channel Spacing

12.5 kHz/25 kHz

Frequency Stability
(-30C to +60C)

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

Power Output
Low Power
High Power

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

1-25 W
25-45 W

1.5 ppm
(without GPS)
0.5 ppm
(with GPS)

1-25 W
25-40 W

Modulation Limiting

2.5 kHz @ 12.5 kHz


5.0 kHz @ 25 kHz

FM Hum and Noise:

-40 dB @ 12.5 kHz


-45 dB @ 25 kHz

Conducted/Radiated
Emission

-36 dBm <1 GHz


-30 dBm >1 GHz

Adjacent Channel
Power (TIA603C)

60 dB @ 12.5 kHz
70 dB @ 25 kHz

Audio Response

TIA603C

Audio Distortion

3%

FM Modulation

12.5 kHz: 11K0F3E


25 kHz: 16K0F3E

4FSK Digital Modulation

12.5 kHz Data Only: 7K60FXD


12.5 kHz Data & Voice: 7K60FXE

Digital Vocoder Type

AMBE+2

Digital Protocol

ETSI-TS102 361-1

Self-Quieter

6880309T86-C

VHF

UHF1

144 MHz

464.025 MHz

147.45 MHz

172.025 MHz +/- 5 kHz

November 14, 2007

1-10

Introduction: Specifications

GPS
Specification

VHF
Numeric Display
Model

UHF1
Display Model

Display Model

Numeric Display
Model

Accuracy specs are for long-term tracking (95th percentile values > 5 satellites visible at a nominal -130
dBm signal strength).
TTFF (Time to First Fix)
Cold Start

< 1 minute

TTFF Hot Start

< 10 seconds

Horizontal Accuracy

< 10 meters
Military Standards 810E & F
MIL-STD 810E

MIL-STD 810F

Methods

Procedures

Methods

Procedures

Low Pressure

500.3

II

500.4

II

High Temperature

501.3

I/A, II/AI

501.4

I/HOT, II/HOT

Low Temperature

502.3

I/C3, II/C1

502.4

I/C3, II/C1

Temperature Shock

503.3

I/AIC3

503.4

Solar Radiation

505.3

505.4

Rain

506.3

I, II

506.4

I, III

Humidity

507.3

II

507.4

Salt Fog

509.3

509.4

Dust

510.3

510.4

Vibration

514.4

I/10, II/3

514.5

I/24

Shock

516.4

I, IV

516.5

I, IV

Environmental Specifications
Operating Temperature

-30C to +60C

Storage Temperature

-40C to +85C

Temperature Shock

Per MIL-STD

Humidity

Per MIL-STD

ESD

IEC 801-2 KV

Water and Dust Intrusion

IP54, MIL-STD

November 14, 2007

6880309T86-C

Chapter 2 Test Equipment and Service Aids

2.1

Recommended Test Equipment


The list of equipment contained in Table 2-1 includes most of the standard test equipment required
for servicing Motorola mobile radios.
Table 2-1 Recommended Test Equipment

Equipment

Characteristic

Example

Application

Service Monitor

Can be used as a
substitute for items
marked with an asterisk
(*)

Aeroflex 2975
(www.aeroflex.com), Motorola
R2670, or equivalent

Frequency/deviation meter and


signal generator for wide-range
troubleshooting and alignment

Digital RMS
Multimeter*

100 V to 300 V
5 Hz to 1 MHz
10 Meg Ohm Impedance

Fluke 179 or equivalent


(www.fluke.com)

AC/DC voltage and current


measurements. Audio voltage
measurements.

RF Signal
Generator*

100 MHz to 1 GHz


-130 dBm to +10 dBM
FM Modulation 0 kHz to
10 kHz

Agilent N5181A
(www.agilent.com), Ramsey
RSG1000B
(www.ramseyelectronics.com),
or equivalent

Receiver measurements

Oscilloscope*

2 Channel
50 MHz Bandwidth
5 mV/div to 20 V/div

Leader LS8050
(www.leaderusa.com), Tektronix
TDS1001b
(www.tektronix.com), or
equivalent

Waveform measurements

Power Meter and


Sensor*

5% Accuracy
100 MHz to 500 MHz
50 Watts

Bird 43 Thruline Watt Meter


(www.bird-electronic.com) or
equivalent

Transmitter power output


measurements

RF Millivolt Meter

100 mV to 3 V RF
10 kHz to 1 GHz

Boonton 92EA
(www.boonton.com) or
equivalent

RF level measurements

Power Supply

0 V to 32 V
0 A to 20 A

B&K Precision 1790


(www.bkprecision.com) or
equivalent

Voltage supply

2-2

2.2

Test Equipment and Service Aids: Service Aids

Service Aids
Table 2-2 lists the service aids recommended for working on the radio. While all of these items are
available from Motorola, most are standard workshop equipment items, and any equivalent item
capable of the same performance may be substituted for the item listed.
Table 2-2 Service Aids
Motorola
Part Number

Description

Application

RLN4460_

Test Set

Enables connection to audio/accessory jack. Allows


switching for radio testing.

PMKN4010_

Mobile & Repeater Rear


Programming Cable

Connects the radios rear connector to a USB port for


radio programming and data applications.

Not Applicable

*Customer Programming
Software

Allows servicer to program radio parameters, tune and


troubleshoot radios.

PMKN4016_

Mobile & Repeater Rear


Accessory Programming and
Test Cable

Connects the radios rear connector to a USB port for


radio programming, data applications, testing and
alignment.

PMKN4018_

Mobile & Repeater Rear


Accessory Connector Universal
Cable

Connects the radios rear connector to accessory


devices such as desk sets. Cable contains all 26 wires
and is unterminated at the user end.

HKN6184_

Mobile Front Programming Cable

Connects the radios front connector to a USB port for


radio programming and data applications.

HLN8027_

Mini UHF to BNC Adaptor

Adapts radio antenna port to BNC cabling of test


equipment.

HPN4007_

Power Supply 25-60W

Provides the radio with power when bench testing.

HPN4008_

Power Supply 1-25W

Provides the radio with power when bench testing.

8180384Y11

Housing Eliminator

Test Fixture used to bench test the radio PCB.

6686119B01

Removal Tool

Assists in the removal of radio control head.

*This kit cannot be purchased. It can be downloaded from http://www.motorola.com/businessonline

2.3

Programming Cables

Figure 2-1 Mobile Front Programming Cable HKN6184_

November 14, 2007

6880309T86-C

Test Equipment and Service Aids: Programming Cables

2-3

Figure 2-2 Mobile & Repeater Rear Programming Cable PMKN4010_

DB 25 CONNECTOR
1

13

14

25

USB CONNECTOR

1455 24
CABLE

915 15
CABLE

WIRE DIAGRAM
REAR ACCESSORY
CONNECTOR

TO MOBILE RADIO
REAR ACCESSORY
CONNECTOR

25

26

VIEWED FROM
FRONT (PIN END)
OF CONNECTOR

PIN No.

DESCRIPTION

USB

VCC (5v)

DATA -

2
3

DB25P

DATA +

GND

SPEAKER -

11

EXT MIC

17

17

DIGI IN 1
(EXT PTT)

20

16

GND

16

10

SPEAKER +

Figure 2-3 Mobile & Repeater Rear Accessory Programming and Test Cable PMKN4016_

6880309T86-C

November 14, 2007

2-4

Test Equipment and Service Aids: Programming Cables

Notes

November 14, 2007

6880309T86-C

Chapter 3 Transceiver Performance Testing

3.1

General
These radios meet published specifications through their manufacturing process by utilizing highaccuracy laboratory-quality test equipment. The recommended field service equipment approaches
the accuracy of the manufacturing equipment with few exceptions. This accuracy must be
maintained in compliance with the manufacturers recommended calibration schedule.
NOTE: Although these radios function in digital and analog modes, all testing is done in analog mode.

3.2

Setup
Supply voltage is provided using a 13.8 VDC power supply. The equipment required for alignment
procedures is connected as shown in the Radio Tuning Equipment Setup Diagram, Figure 4-4.
Initial equipment control settings should be as indicated in Table 3-1. The remaining tables in this
chapter contain the following related technical data:
Table Number

Title

3-2

Front Panel Access Test Mode Displays

3-3

Test Environments

3-4

Test Channel Spacing

3-5

Test Frequencies

3-6

Transmitter Performance Checks

3-7

Receiver Performance Checks

Table 3-1 Initial Equipment Control Settings


Service Monitor

Power Supply

Test Set

Monitor Mode: Power Monitor

Voltage: 13.8 VDC

Speaker set: A

RF Attenuation: -70

DC On/Standby:
Standby

Speaker/load:
Speaker

AM, CW, FM: FM

Volt Range: 20 V

PTT: OFF

Oscilloscope Source: Mod


Oscilloscope Horizontal: 10 mSec/Div
Oscilloscope Vertical: 2.5 kHz/Div
Oscilloscope Trigger: Auto
Monitor Image: Hi
Monitor Bandwidth: Narrow
Monitor Squelch: middle setting
Monitor Vol: 1/4 setting

Current: 20 A

3-2

Transceiver Performance Testing: Display Model Test Mode

3.3

Display Model Test Mode

3.3.1

Entering Display Radio Test Mode


1. Turn the radio on.
2. Within ten seconds after self test is complete, press button P2, five times in succession.
3. The radio beeps and will show a series of displays that will give information regarding various
version numbers and subscriber specific information. The displays are described in Table 3-2.
Table 3-2 Front Panel Access Test Mode Displays
Name of Display

Description

Appears

Service Mode

The literal string indicates the radio has entered test mode.

Always

Host Version

The version of host firmware.

Always

DSP Version

The version of DSP firmware.

Always

Model Number

The radios model number as programmed in the codeplug.

Always

MSN

The radios serial number as programmed in the codeplug.

Always

FLASHCODE

The FLASH codes as programmed in the codeplug.

Always

RF Band

The radios band.

Always

NOTE: The radio stops at each display for 2 seconds before moving to the next information display.
If the information cannot fit into 1 line, the radio display scrolls automatically character by
character after 1 second to view the whole information. If the Left Navigation Button (W) is
pressed before the last information display, the radio shall suspend the information display
until the user presses Right Navigation Button ( X) to resume the information display. The
radio beeps for each button press. After the last display, RF Test Mode will be displayed.

3.3.2

RF Test Mode
When the radio is operating in its normal environment, the radio's microcontroller controls the RF
channel selection, transmitter key-up, and receiver muting, according to the customer codeplug
configuration. However, when the unit is on the bench for testing, alignment, or repair, it must be
removed from its normal environment via a special routine, called TEST MODE or air test.
In RF Test Mode, the display upon the first line is RF Test, together with the power level icon at the
right end of the first line. The display upon the second line is the test environment, the channel
number and channel spacing (CSQ CHXX SP25). The default test environment is CSQ.
1. Each short press of button P2 changes the test environment
(CSQ->TPL->DIG->USQ->CSQ). The radio beeps once when radio toggles to CSQ, beeps
twice for TPL, beeps three times for DIG and beeps four times for USQ.
NOTE: DIG is digital mode and other test environments are analog mode as described in Table 3-3.
2. Each short press of button P1 toggles the channel spacing between 20 kHz, 25 kHz and
12.5 kHz. The radio beeps once when radio toggles to 20 kHz, beeps twice for 25 kHz and
beeps three times for 12.5 kHz.
3. Turning of the Channel Rocker changes the test channel from 1 to 14 as described in
Table 3-5. The radio beeps in each position.

November 14, 2007

6880309T86-C

Transceiver Performance Testing: Display Model Test Mode

3.3.3

3-3

Display Test Mode


1. Press and hold button P1 in RF Test Mode. The radio beeps once and momentarily displays
Display Test Mode.
2. Upon entering Display Test Mode, the radio displays a horizontal line on row 8 (center row).
3. With each button press, the radio fills up the screen with 2 horizontal lines from the center row
(1 line each above and below the center row) until the top and bottom of the screen (row 7-0
and 9-16) is complete filled.
4. When the screen is filled up with the horizontal lines, any button press clears the screen and
displays vertical lines at column 0, 6, 12, 18, 24, 30, 36, 42, 48, 54, 60. Any button press fills
the screen with vertical lines, (1 line to the right of any existing lines) until the display is filled.
5. When the screen is filled up with the vertical lines, any button press clears the screen and
displays the first 10 available icons on the screen. Successive button press displays the
remaining 4 icons.

3.3.4

LED Test Mode


1. Press and hold button P1 after Display Test Mode. The radio beeps once and displays
LED Test Mode.
2. Upon any button press, the radio lights on the red LED and displays Red LED On.
3. Consequently, upon any button press, the red LED is turned off and the radio lights on the
green LED and displays Green LED On.
4. Consequently, upon any button press, the green LED is turned off and the radio shall light on
the yellow LED and displays Yellow LED On.

3.3.5

Backlight Test Mode


1. Press and hold button P1 after LED Test Mode. The radio beeps once and displays
Backlight Test Mode.
2. The radio lights on both LCD and keypad backlight together.

3.3.6

Speaker Tone Test Mode


1. Press and hold button P1 after Backlight Test Mode. The radio beeps once and displays
Speaker Tone Test Mode.
2. The radio generates a 1 kHz tone with the internal speaker.

3.3.7

Earpiece Tone Test Mode


1. Press and hold button P1 after Speaker Tone Test Mode. The radio beeps once and displays
Earpiece Tone Test Mode.
2. The radio generates a 1 kHz tone with the earpiece.

3.3.8

Audio Loopback Test Mode


1. Press and hold button P1 after Earpiece Tone Test Mode. The radio beeps once and
displays Audio Loopback Test Mode.
2. The radio shall route any audio on the mic to the earpiece.

6880309T86-C

November 14, 2007

3-4

3.3.9

Transceiver Performance Testing: Numeric Display Model Test Mode

Audio Loopback Earpiece Test Mode


1. Press and hold button P1 after Audio Loopback Test Mode. The radio beeps once and
displays Audio Loopback Earpiece Test Mode.
2. The radio shall route any audio on the external mic to the earpiece.

3.3.10 Button/Knob/PTT Test Mode


1. Press and hold button P1 after Audio Loopback Earpiece Test Mode. The radio beeps once
and displays Button Test (line 1).
2. The radio also displays the button/knob/PTT button command opcode (BCO) and state
(BCO/state) on the screen (line 2) upon any button state changes.

3.4

Numeric Display Model Test Mode

3.4.1

Entering Display Radio Test Mode


1. Turn the radio on.
2. Within ten seconds after self test is complete, press button P2, five times in succession.
3. The radio beeps.

3.4.2

RF Test Mode
When the radio is operating in its normal environment, the radio's microcontroller controls the RF
channel selection, transmitter key-up, and receiver muting, according to the customer codeplug
configuration. However, when the unit is on the bench for testing, alignment, or repair, it must be
removed from its normal environment via a special routine, called TEST MODE or air test.
1. Each short press of button P2 changes the test environment
(CSQ->TPL->DIG->USQ->CSQ). The radio beeps once when radio toggles to CSQ, beeps
twice for TPL, beeps three times for DIG and beeps four times for USQ.
NOTE: DIG is digital mode and other test environments are analog mode as described in Table 3-3.
2. Each short press of button P1 toggles the channel spacing between 20 kHz, 25 kHz and
12.5 kHz. The radio beeps once when radio toggles to 20 kHz, beeps twice for 25 kHz and
beeps three times for 12.5 kHz.
3. Turning of the Channel Rocker changes the test channel from 1 to 14 as described in
Table 3-5. The radio beeps in each position.

3.4.3

Display Test Mode


1. Press and hold button P1 in RF Test Mode. The radio beeps once and enters
Display Test Mode.
2. Upon entering Display Test Mode, press any button to turn on the two character seven
segment display.
3. Press any button to display the three icons on the screen.

November 14, 2007

6880309T86-C

Transceiver Performance Testing: Numeric Display Model Test Mode

3.4.4

3-5

LED Test Mode


1. Press and hold button P1 after Display Test Mode. The radio beeps once.
2. Upon any button press, the radio lights on the red LED.
3. Consequently, upon any button press, the red LED is turned off and the radio lights on the
green LED.
4. Consequently, upon any button press, the green LED is turned off and the radio shall light on
the yellow LED.

3.4.5

Speaker Tone Test Mode


1. Press and hold button P1 after LED Test Mode. The radio beeps once.
2. The radio generates a 1 kHz tone with the internal speaker.

3.4.6

Earpiece Tone Test Mode


1. Press and hold button P1 after Speaker Tone Test Mode. The radio beeps once.
2. The radio generates a 1 kHz tone with the earpiece.

3.4.7

Audio Loopback Test Mode


1. Press and hold button P1 after Earpiece Tone Test Mode. The radio beeps once.
2. The radio shall route any audio on the mic to the earpiece.

3.4.8

Audio Loopback Earpiece Test Mode


1. Press and hold button P1 after Audio Loopback Test Mode. The radio beeps once.
2. The radio shall route any audio on the external mic to the earpiece.

3.4.9

Button/Knob/PTT Test Mode


1. Press and hold button P1 after Audio Loopback Earpiece Test Mode. The radio beeps once.
2. Rotate the volume knob, the radio beeps at each position.
3. Press any button, the radio beeps.

Table 3-3 Test Environments


No. of
Beeps

Description

Function

Carrier Squelch
(CSQ)

RX: unsquelch if carrier detected


TX: mic audio

Tone Private-Line
(TPL)

RX: unsquelch if carrier and tone (192.8 Hz) detected


TX: mic audio + tone (192.8 Hz)

Digital
(DIG)

RX: unsquelch if carrier and digital code detected


TX: mic audio

Unsquelch
(USQ)

RX: constant unsquelch


TX: mic audio

6880309T86-C

November 14, 2007

3-6

Transceiver Performance Testing: Numeric Display Model Test Mode

Table 3-4 Test Channel Spacing


Number of Beeps

Channel Spacing

20 kHz

25 kHz

12.5 kHz

Table 3-5 Test Frequencies


Test
Mode

Test Channel
Low Power

Test Channel
High Power

TX

136.075

403.000

RX

136.075

403.000

TX

142.575

414.150

RX

142.575

414.150

TX

10

146.575

425.350

RX

10

146.575

425.350

TX

11

155.575

436.500

RX

11

155.575

436.500

TX

12

161.575

447.675

RX

12

161.575

447.675

TX

13

167.575

458.850

RX

13

167.575

458.850

TX

14

174.975

470.000

RX

14

174.975

470.000

November 14, 2007

VHF

UHF1

6880309T86-C

Transceiver Performance Testing: Numeric Display Model Test Mode

3-7

Table 3-6 Transmitter Performance Checks


Test Name

Communications
Analyzer

Radio

Test Set

Comment

Reference
Frequency

Mode: PWR MON


4th channel test frequency*
Monitor: Frequency error
Input at RF In/Out

TEST MODE,
Test Channel 4,
carrier squelch

PTT to
continuously
transmit (during
the performance
check)

Frequency error:
90 Hz (VHF)
150 Hz (UHF)

Power RF

As above

TEST MODE
Test Channel 4,
carrier squelch

As above

Low Power:
1.0-1.3 W (VHF 1-25 W,
(UHF 1-25 W)
25-29 W (VHF 25-45 W,
UHF 25-40 W)

TEST MODE
Test Channel 11,
carrier squelch

High Power:
25-29 W (VHF 1-25W,
UHF 1-25 W)
40-47 W (UHF 25-40 W)
45-53 W (VHF 25-45 W)

Voice
Modulation

Mode: PWR MON


4th channel test frequency*
atten to -70, input to RF In/
Out
Monitor: DVM, AC Volts
Set 1kHz Mod Out level for
800mVrms at test set,
800mVrms at AC/DC test
set jack

TEST MODE
Test Channel 4,
carrier squelch

As above, meter
selector to mic

Deviation:
2.5 kHz Max.
(12.5 kHz Ch. Sp.).
4 kHz Max.
(20 kHz Ch. Sp.).
5 kHz Max.
(25 kHz Ch. Sp.).

Voice
Modulation
(internal)

Mode: PWR MON


4th channel test frequency*
atten to -70, input to RF In/
Out

TEST MODE,
Test Channel 4
carrier squelch
output at
antenna

Remove
modulation input

Deviation:
2.5 kHz Max.
(12.5 kHz Ch. Sp.).
4 kHz Max.
(20 kHz Ch. Sp.).
5 kHz Max.
(25 kHz Ch. Sp.).

TPL
Modulation

As above
4th channel test frequency*
BW to narrow

TEST MODE,
Test Channel 4
TPL

As above

Deviation:
0.25-0.5 kHz
(12.5 kHz Ch. Sp.).
0.4-0.8 kHz
(20 kHz Ch. Sp.).
0.5-1.0 kHz
(25 kHz Ch. Sp.).

* See Table 3-5

6880309T86-C

November 14, 2007

3-8

Transceiver Performance Testing: Numeric Display Model Test Mode

Table 3-7 Receiver Performance Checks


Communications
Analyzer

Test Name

Radio

Test Set

Comment

Rated Audio

Mode: GEN
Output level: 1.0 mV RF
4th channel test
frequency*
Mod: 1 kHz tone at
3 kHz deviation
Monitor: DVM: AC Volts

TEST MODE
Test Channel 4,
25 kHz channel
spacing,
carrier squelch

PTT to OFF
(center),
meter
selector to
Audio PA

Set volume
control to
7.75 Vrms

Distortion

As above, except to
distortion

As above

As above

Distortion <5.0%

Sensitivity
(SINAD)

As above, except SINAD,


lower the RF level for
12 dB SINAD.

As above

PTT to OFF
(center)

RF input to be
<0.3 V

RF level set to 1 mV RF

As above

PTT to OFF
(center),
meter
selection to
Audio PA,
spkr/ load to
speaker

Set volume
control to
7.75 Vrms

As above, except change


frequency to a
conventional system.
Raise RF level from zero
until radio unsquelches.

out of TEST
MODE; select a
conventional
system

As above

Unsquelch to
occur at <0.25 V.
Preferred SINAD
= 9-10 dB

Noise
Squelch
Threshold
(only radios
with
conventional
system need
to be tested)

* See Table 3-5

November 14, 2007

6880309T86-C

Chapter 4 Radio Programming and Tuning

4.1

Introduction
This chapter provides an overview of the MOTOTRBO Customer Programming Software (CPS), as
well as the Tuner and AirTracer applications, which are all designed for use on a Windows 2000/XP
operating system. These programs are available as listed in Table 4-1. An Installation Guide is also
included with the kit.
NOTE: Refer to the appropriate program on-line help files for the programming procedures.
Table 4-1 Radio Software Program Kit
Description
*MOTOTRBO CPS, Tuner and AirTracer Applications
*This kit cannot be purchased. It can be downloaded from http://www.motorola.com/businessonline

Customer Programming Software Setup


The Customer Programming Software setups, shown in Figure 4-1 and Figure 4-2, are used to
program the radio.
NOTE: Refer to the appropriate program on-line help files for the programming procedures.

Front Connector

ACC
R a d io

4.2

DC
RF

13.8VDC
Power
Supply

Mobile Front Programming Cable HKN6184_

USB

Figure 4-1 Customer Programming Software Setup from Front Connector

4-2

Radio Programming and Tuning: AirTracer Application Tool

Radio

ACC

Rear Accessory
Connector

Mobile & Repeater Rear


Programming Cable PMKN4010_

DC
RF

13.8 VDC
Power
Supply

USB

Figure 4-2 Customer Programming Software Setup from Rear Accessory Connector

Radio

ACC

Mobile & Repeater Rear Accessory


Programming and Test Cable PMKN4016_

Rear Accessory
Connector

Test Box RLN4460_


No
Connection

DC
RF

13.8 VDC
Power
Supply

USB

Figure 4-3 Customer Programming Software Setup with Test Box Connection

4.3

AirTracer Application Tool


The MOTOTRBO AirTracer application tool has the ability to capture over-the-air digital radio traffic
and save the captured data into a file. The AirTracer application tool can also retrieve and save
internal error logs from MOTOTRBO radios. The saved files can be analyzed by trained Motorola
personnel to suggest improvements in system configurations or to help isolate problems.

November 14, 2007

6880309T86-C

Radio Programming and Tuning: Radio Tuning Setup

4.4

4-3

Radio Tuning Setup


A personal computer (PC), Windows 2000/XP and a tuner program (which is available as part of the
MOTOTRBO CPS kit) are required to tune the radio. To perform the tuning procedures, the radio
must be connected to the PC and test equipment setup as shown in Figure 4-4.
Audio In
Test Box
RLN44 60_

Tx

Audio Generator

Rx

SINAD Meter
AC Voltmet er

Mobile & Repeater Rear Accessory


Programming and Test Cable PMKN4016_

R a d io

ACC
DC
RF

13. 8VDC
Power
Supply

USB

30 dB Pad

Tx

Mini UHF
to BNC
HLN8027_
(if needed )

Service Monitor

Tx

WATT meter

RF Generator

Figure 4-4 Radio Tuning Equipment Setup

6880309T86-C

November 14, 2007

4-4

Radio Programming and Tuning: Radio Tuning Setup

Notes

November 14, 2007

6880309T86-C

Chapter 5 Disassembly/Reassembly Procedures

5.1

Introduction
This chapter provides details about the following:
Preventive maintenance (inspection and cleaning).
Safe handling of CMOS and LDMOS devices.
Disassembly and reassembly of the radio.
Repair procedures and techniques.

5.2

Preventive Maintenance
Periodic visual inspection and cleaning is recommended.

5.2.1

Inspection
Check that the external surfaces of the radio are clean, and that all external controls and switches
are functional. It is not recommended to inspect the interior electronic circuitry.

5.2.2

Cleaning Procedures
The following procedures describe the recommended cleaning agents and the methods to be used
when cleaning the external and internal surfaces of the radio. External surfaces include the control
head and housing assembly. These surfaces should be cleaned whenever a periodic visual
inspection reveals the presence of smudges, grease, and/or grime.
NOTE: Internal surfaces should be cleaned only when the radio is disassembled for service or repair.
The only recommended agent for cleaning the external radio surfaces is a 0.5% solution of a mild
dishwashing detergent in water. The only factory recommended liquid for cleaning the printed circuit
boards and their components is isopropyl alcohol (100% by volume).

!
Caution

The effects of certain chemicals and their vapors can have harmful results on
certain plastics. Avoid using aerosol sprays, tuner cleaners and other
chemicals.

5-2

Disassembly/Reassembly Procedures: Safe Handling of CMOS and LDMOS Devices

Cleaning External Plastic Surfaces


Apply the 0.5% detergent-water solution sparingly with a stiff, non-metallic, short-bristled brush to
work all loose dirt away from the radio. Use a soft, absorbent, lintless cloth or tissue to remove the
solution and dry the radio. Make sure that no water remains entrapped near the connectors, cracks,
or crevices.
Cleaning Internal Circuit Boards and Components
Isopropyl alcohol (100%) may be applied with a stiff, non-metallic, short-bristled brush to dislodge
embedded or caked materials located in hard-to-reach areas. The brush stroke should direct the
dislodged material out and away from the inside of the radio. Make sure that controls or tunable
components are not soaked with alcohol. Do not use high-pressure air to hasten the drying process
since this could cause the liquid to collect in unwanted places. Once the cleaning process is
complete, use a soft, absorbent, lintless cloth to dry the area. Do not brush or apply any isopropyl
alcohol to the frame, control head and housing assembly.
NOTE: Always use a fresh supply of alcohol and a clean container to prevent contamination by
dissolved material (from previous usage).

5.3

Safe Handling of CMOS and LDMOS Devices


Complementary metal-oxide semiconductor (CMOS) devices are used in this family of radios, and
are susceptible to damage by electrostatic or high voltage charges. Damage can be latent, resulting
in failures occurring weeks or months later. Therefore, special precautions must be taken to prevent
device damage during disassembly, troubleshooting, and repair.
Handling precautions are mandatory for CMOS circuits and are especially important in low humidity
conditions.

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Safe Handling of CMOS and LDMOS Devices

5-3

DO NOT attempt to disassemble the radio without first referring to the following CAUTION
statement.

!
Caution

This radio contains static-sensitive devices. Do not open the radio unless you are
properly grounded. Take the following precautions when working on this unit:

Store and transport all CMOS devices in conductive material so that


all exposed leads are shorted together. Do not insert CMOS devices
into conventional plastic snow trays used for storage and
transportation of other semiconductor devices.
Ground the working surface of the service bench to protect the
CMOS device. We recommend using a wrist strap, two ground
cords, a table mat, and a floor mat.
Wear a conductive wrist strap in series with a 100k resistor to
ground. (Replacement wrist straps that connect to the bench top
covering are Motorola part number 4280385A59).
Do not wear nylon clothing while handling CMOS devices.
Do not insert or remove CMOS devices with power applied. Check
all power supplies used for testing CMOS devices to be certain that
there are no voltage transients present.
When straightening CMOS pins, provide ground straps for the
apparatus used.
When soldering, use a grounded soldering iron.
If at all possible, handle CMOS devices by the package and not by
the leads. Prior to touching the unit, touch an electrical ground to
remove any static charge that you may have accumulated. The
package and substrate may be electrically common. If so, the
reaction of a discharge to the case would cause the same damage
as touching the leads.

6880309T86-C

November 14, 2007

5-4

5.4

Disassembly/Reassembly Procedures: Repair Procedures and Techniques General

Repair Procedures and Techniques General


NOTE

Environmentally Preferred Products (EPP) (refer to the marking on the printed circuit
boards examples shown below) were developed and assembled using environmentally preferred components and solder assembly techniques to comply with the European Unions Restriction of Hazardous Substances (ROHS) Directive 2002/95/EC
and Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC. To
maintain product compliance and reliability, use only the Motorola specified parts in this
manual.

Any rework or repair on Environmentally Preferred Products must be done using the appropriate
lead-free solder wire and lead-free solder paste as stated in the following table:
Table 5-1 Lead Free Solder Wire Part Number List
Motorola
Part Number

Alloy

Flux Type

Flux Content
by Weight

Melting
Point

Supplier Part
number

Diameter

Weight

1088929Y01

95.5Sn/3.8Ag/0.7Cu

RMA Version

2.7-3.2%

217C

52171

0.015

1lb spool

Table 5-2 Lead Free Solder Paste Part Number List


Motorola Part
Number

Manufacturer Part
Number

1085674C03

NC-SMQ230

Viscosity

Type

Composition & Percent Metal

900-1000KCPs
Brookfield (5rpm)

Type 3
(-325/+500)

(95.5%Sn-3.8%Ag-0.7%Cu)
89.3%

Liquid
Temperature
217C

Parts Replacement and Substitution


When damaged parts are replaced, identical parts should be used. If the identical replacement part
is not locally available, check the parts list for the proper Motorola part number and order it.
Rigid Circuit Boards
This family of radios uses bonded, multi-layer, printed circuit boards. Since the inner layers are not
accessible, some special considerations are required when soldering and unsoldering components.
The printed-through holes may interconnect multiple layers of the printed circuit. Therefore, exercise
care to avoid pulling the plated circuit out of the hole.
When soldering near a connector:
Avoid accidentally getting solder in the connector.
Be careful not to form solder bridges between the connector pins.
Examine your work closely for shorts due to solder bridges.

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Disassembling and Reassembling the Radio General

5.5

5-5

Disassembling and Reassembling the Radio General


Since these radios may be disassembled and reassembled with the use of only seven screws (board
to casting), it is important to pay particular attention to the snaps and tabs, and how parts align with
each other.
The following tools are required for disassembling the radio:
Small Flat Blade Screwdriver
Dismantling Tool (Motorola Part No. 6686119B01)
Torque Driver (5-30 lbs-in or 0.6-3.5 N-m), (Motorola Part No. RSX4043A)
TORX T20 Driver Bit
TORX T10 Driver Bit
TORX T6 Driver Bit (for use with Option Board only)
5/16 Socket Driver (GPS Models Only)
If a unit requires more complete testing or service than is customarily performed at the basic level,
please send radio to a Motorola Service Center listed in Appendix B.
The following disassembly procedures should be performed only if necessary.

5.6

Radio Disassembly Detailed


The procedure to remove and replace the control head, top cover or transceiver board is similar for
all models. A typical procedure is therefore provided in this section followed by detailed disassembly
procedures for each specific control head model.

5.6.1

Control Head Removal


1. Insert the dismantling tool in the groove between the control head and the radio assembly as
shown in Figure 5-1.
2. Press the dismantling tool under the control head to release the snap features.
Dismantling
Tool

Figure 5-1 Typical Control Head Removal

6880309T86-C

November 14, 2007

5-6

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

3. Pull the control head away from the radio assembly as shown in Figure 5-2.

Mic Jack Pad


Flex Cable

Control Head Seal


Speaker Pad
Socket
Figure 5-2 Flexible Connection Removal
4. Remove the flex cable from the socket on the radio assembly as shown in Figure 5-2.
5. Then remove control head seal, mic jack pad and speaker pad.

5.6.2

Top Cover Removal


1. Insert the dismantling tool between the top cover and the chassis as shown in
Figure 5-3.
2. Press on the dismantling tool until the side wall of the top cover clears the chassis trunnion
mounting features.
3. Lift the top cover from the chassis.
Trunnion Mounting
Feature

Dismantling
Tool
Figure 5-3 Top Cover Removal
NOTE: See Section 5.6.7 for Option Board Removal procedure (Option Board Module Only).

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

5.6.3

5-7

Transceiver Board Removal


1. Remove the seven screws from the die cast cover using the T20 TORX driver as shown in
Figure 5-4.
NOTE: Do not remove the O-rings from the screws.
2. Lift the die cast cover from the chassis.
NOTE: For VHF models only: check that the two thermal pads on the heat sink block are intact.
Replace them if damaged. Refer to Figure 5-53.

Screws (7)

Die Cast
Cover

Radio
Chassis

Figure 5-4 Die Cast Cover Removal

6880309T86-C

November 14, 2007

5-8

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

3. Remove the rear accessory connector from the radio assembly by inserting a flat-blade
screwdriver into the slot on the side of the connector as shown in Figure 5-5.

!
Caution

The rear accessory connector should never be removed when the cover is still
assembled to the radio.

Flat-blade
Screwdriver

Rear Accessory
Connector

Slot

Figure 5-5 Rear Accessory Connector Removal


4. Remove the RF/DC retention clips by gently prying them out with a flat-blade screwdriver as
shown in Figure 5-6.
RF/DC Retention Clips

Flat-blade
Screwdriver

Flat-blade
Screwdriver

Figure 5-6 RF/DC Retention Clips Removal


November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

5-9

5. For GPS models, disconnect the GPS cable from the radio as shown in Figure 5-7.
GPS Cable

Figure 5-7 GPS Cable Removal


6. Remove the transceiver board by sliding a finger into the opening provided at the front of the
radio and gently pressing up on the 30-pin connector, lifting up the front of the transceiver
board, as shown in Figure 5-8. Then, slide the transceiver board towards the front of the radio
to allow the RF/DC connectors to clear the chassis. Handle the transceiver board by the
edges only and store it in an antistatic bag.
NOTE: If the RF/DC connector gaskets remain in the chassis, remove them and place them back on
the connectors.

!
Caution

The thermal pads can act as an adhesive and cause stress to critical
components on the transceiver board if the transceiver board is lifted too
quickly.

Figure 5-8 Transceiver Board Removal

6880309T86-C

November 14, 2007

5-10

5.6.4

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

GPS Antenna Connector Removal (For GPS models only)


1. Using a 5/16 socket driver, remove the nut from the GPS antenna connector and remove the
lock nut washer from the connector.
2. Push the connector into the chassis and pull upwards on the cable to remove the connector
from the chassis.

5.6.5

Disassembly of Display Model Control Head


1. Disconnect the speaker plug from the control head board.
2. Unplug the LCD display flex from the control head board by gently lifting upwards on the door
of the connector.

LCD Display Flex

Figure 5-9 LCD Display Flex Removal


3. Remove the left and right arrow keys from the front of the control head assembly by using
your fingers.

Left Arrow Key

Right Arrow Key

Figure 5-10 Left and Right Arrow Key Removal

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

5-11

4. Remove the five screws from the control head board using the T10 TORX driver.
NOTE: Do not touch or contaminate the conductive contacts on the control head board.

Control Head Board


Figure 5-11 Control Head Board Removal
5. Remove the keypad from the control head housing by lifting up on the rubber keypad.

Keypad

Figure 5-12 Keypad Removal


NOTE: Care should be taken not to touch or contaminate the conductive pads on the keypad.

6. Remove the LCD display from the control head housing.


7. Remove the speaker retainer from the control head housing using the T10 TORX driver to
remove the screw and unhook the retainer from the control head housing.
8. Remove the speaker from the control head housing.

6880309T86-C

November 14, 2007

5-12

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

9. Remove the volume knob from the control head housing by pulling it until the snaps are
released.

Housing Assembly

Volume Knob

Figure 5-13 Volume Knob Removal

5.6.6

Disassembly of Numeric Display Model Control Head


1. Disconnect the speaker plug from the control head board.
2. Remove the five screws from the control head board using the T10 TORX driver.
3. Remove the control head board from the control head assembly by pressing on the keypad
buttons and mic jack. Handle the control head board by the edges only and store it in an
antistatic bag.

Control Head Board

Figure 5-14 Control Head Board Removal


NOTE: Do not touch or contaminate the conductive contacts on the control head board.

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

5-13

4. Remove the icon light guide from the icon light guide holder.

Icon Light Guide

Figure 5-15 Icon Light Guide Removal

5. Remove the keypad from the control head housing by lifting up on the rubber keypad.

Rubber Keypad

Figure 5-16 Keypad Removal


NOTE: Care should be taken not to touch or contaminate the conductive pads on the keypad.

6880309T86-C

November 14, 2007

5-14

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

6. Remove the icon light guide holder from the keypad.

Keypad

Light Guide Holder

Figure 5-17 Icon Light Guide Holder Removal


7. Remove the speaker retainer from the control head housing using the T10 TORX driver to
remove the screw and unhook the retainer from the control head housing.
8. Remove the speaker from the control head housing.
9. Remove the volume knob from the control head housing by pulling it until the snaps are
released.

Volume Knob

Figure 5-18 Speaker and Volume Knob Removal

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Disassembly Detailed

5.6.7

5-15

Option Board Module Removal


1. Remove option flex from the radio assembly and option board as shown in Figure 5-19.

Option Board
Option Flex (8415457H01)
Figure 5-19 Removing Option Flex from Option Board
2. Remove the four screws and the option board from the radio assembly using the T6 TORX
driver as shown in Figure 5-20.

Option Board

Screws (0386104Z04)
Figure 5-20 Removing Option Board from Radio Assembly

6880309T86-C

November 14, 2007

5-16

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5.7

Radio Reassembly Detailed

5.7.1

Display Model Control Head


1. Place the LCD display inside the control head housing, making sure to align the D-shaped
feature on the LCD display with the pin feature on the housing. Refer to Figure 5-21.
LCD Assembly

D-Shaped Feature

Pin Feature
Housing Assembly
Figure 5-21 LCD Display Placement

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-17

2. Assemble the keypad to the control head housing:


a. If attached, remove the right and left arrow buttons by pulling them off the keypad.
Set these aside to be assembled later.
b. Assemble the keypad in the control head housing making sure to align the keys with the
openings in the control head housing. Refer to Figure 5-22.

Housing Assembly

Left Arrow Key

Right Arrow
Key

Keypad
Assembly

Figure 5-22 Keypad Assembly


NOTE: Care should be taken not to touch or contaminate the conductive pads on the keypad.
3. Assemble the light guide and light guide holder into the keypad slot as shown in Figure 5-23.

Housing Assembly

Light Guide

Light Guide Holder

Figure 5-23 Light Guide Assembly

6880309T86-C

November 14, 2007

5-18

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

4. Assemble PCB to the control head assembly.


a. Assemble the mic jack seal around the mic jack as shown in Figure 5-24.
NOTE: Make sure the mic jack is free from dust or debris.

Mic Jack Seal

Mic Jack
Figure 5-24 Assembling Mic Jack Seal
b. Assemble the board to the control head assembly using the mic jack as the primary point
of alignment. Make sure the LCD display flex is extended through the slot on the board.
Verify the board is seated properly, as the guide pin on the housing should extend through
the board. Refer to Figure 5-25.

Slot

Guide Pin

Figure 5-25 Assembling Board to Control Head Assembly

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-19

c. Using a T10 TORX driver, tighten the five screws to 0.882 N-m (7.8 lbs-in) following the
sequence as shown in Figure 5-26.

Figure 5-26 Screw Sequence


5. Assemble the speaker into the control head assembly.
a. Place the speaker in the control head assembly as shown in Figure 5-27.
Speaker Terminal

Speaker Terminal
Figure 5-27 Speaker Assembly
b. Hook one side of the speaker retainer into the control head assembly as shown in Figure
5-28.

Hook Retainer Here


Figure 5-28 Speaker Retainer Assembly
c. Place a screw into the other end of the speaker retainer and using a T10 TORX driver,
tighten the screw to 0.882 N-m (7.8 lbs-in).
d. Connect the speaker plug to its mating connector on the control head board.

6880309T86-C

November 14, 2007

5-20

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

6. Insert the LCD display flex to the connector on the control head board and gently close the
door.
7. Assemble the left and right arrow keys into the openings in the control head housing and
press into place as shown in Figure 5-29.

Housing Assembly

Left Arrow
Key
Right Arrow
Key

Figure 5-29 Left and Right Arrow Key Assembly


8. Assemble the flex cable to the mating connector on the control head board, making sure it is
fully seated as shown in Figure 5-30.

Flex Cable

Figure 5-30 Flex Cable Assembly

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-21

9. Orient the volume knob so that the internal D-shaped opening matches the volume encoder
shaft and press the volume knob into the control head assembly until the snap features are
engaged and the knob rotates freely. Refer to Figure 5-31.

Volume Knob

Volume Encoder Shaft

Figure 5-31 Volume Knob Assembly

5.7.2

Numeric Display Model Control Head


1. Place the icon light guide holder into the keypad. Refer to Figure 5-32.

Keypad

Icon Light Guide Holder

Figure 5-32 Icon Light Guide Holder Assembly

6880309T86-C

November 14, 2007

5-22

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

2. Assemble the keypad in the control head housing making sure to align the keys with the
openings in the control head housing. Refer to Figure 5-33.

Control Head Housing

Keypad

Figure 5-33 Keypad Assembly


NOTE: Care should be taken not to touch or contaminate the conductive pads on the keypad.

3. Assemble the icon light guide into the icon light guide holder as shown in Figure 5-34.

Icon Light Guide


Icon Light Guide Holder

Figure 5-34 Icon Light Guide Assembly

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-23

4. Assemble the light guide and light guide holder into the keypad slot as shown in Figure 5-35.
Light Guide Holder

Light Guide

Figure 5-35 Light Guide and Light Guide Holder Assembly


5. Assemble PCB to the control head assembly.
a. Assemble the mic jack seal around the mic jack as shown in Figure 5-36.

Mic Jack

Mic Jack Seal

Figure 5-36 Mic Jack Seal Assembly


NOTE: Make sure the mic jack seal is free from dust or debris.

6880309T86-C

November 14, 2007

5-24

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

b. Assemble the LED display spacer and LED display to the control head PCB as shown in
Figure 5-37.

Control Head PCB


LED Display Spacer

LED Display

Figure 5-37 LED Display Assembly


c. Assemble the board to the control head assembly using the mic jack as the primary point
of alignment. Verify the board is seated properly, as the guide pin on the housing should
extend through the board. Refer to Figure 5-38.

Guide Pin
Figure 5-38 Printed Circuit Board Assembly

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-25

d. Using a T10 TORX driver, tighten the five screws to 0.882 N-m (7.8 lbs-in) following the
sequence as shown in Figure 5-39.

4
5

Figure 5-39 Screw Sequence


6. Assemble the speaker into the control head assembly.
a. Place the speaker in the control head assembly as shown in Figure 5-40.
Speaker Terminal

Speaker Terminal
Figure 5-40 Speaker Assembly

6880309T86-C

November 14, 2007

5-26

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

b. Hook one side of the speaker retainer into the control head assembly as shown in Figure
5-41.

Hook Retainer Here

Figure 5-41 Speaker Retainer Assembly


c. Place a screw into the other end of the speaker retainer and using a T10 TORX driver,
tighten the screw to 0.882 N-m (7.8 lbs-in).
d. Connect the speaker plug to its mating connector on the control head board.
7. Assemble the flex cable to the mating connector on the control head board, making sure it is
fully seated as shown in Figure 5-42.

Flex Cable

Figure 5-42 Flex Cable Assembly

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-27

8. Orientate the volume knob so that the internal D-shaped opening matches the volume
encoder shaft and press the volume knob into the control head assembly until the snap
features are engaged and the knob rotates freely. Refer to Figure 5-43.

Volume Knob

Volume Encoder Shaft


Figure 5-43 Volume Knob Assembly

6880309T86-C

November 14, 2007

5-28

5.7.3

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

Radio Assembly
1. Prior to reassembling the radio, inspect all seals and sealing surfaces for damage (nicks,
cuts, etc.) or debris. Refer to the exploded view and bill of materials for the correct part
numbers and replace parts, as necessary. Reseat all new seals on their respective parts.
For both the die cast cover and the chassis, thoroughly inspect the shield gasketing for
damage and verify all thermal pads are in place and free from damage and debris. See
Section 5.7.6: Thermal Pad Replacement Procedure on page 5-36 to replace damaged pads.

Chassis with Thermal Pads


and Shield Gasketing

Die Cast Cover with Thermal Pads


and Shield Gasketing

Figure 5-44 Thermal Pads and Shield Gasketing on Chassis and Die Cast Cover
2. Thoroughly inspect the transceiver board and verify all thermal pads are in place and free
from damage. See Section 5.7.6: Thermal Pad Replacement Procedure on page 5-36 to
replace damaged pads.

Transistor
Thermal Pads
(7515582H01)

PA Thermal Pad (7515581H01)

Audio PA Component

Figure 5-45 Transceiver Board with Thermal Pad

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5.7.4

5-29

GPS Plug or GPS Antenna Connector Reassembly


1. Assembly of the GPS Plug
Push the GPS plug into the chassis opening until it is fully seated. Refer to Figure 5-46.
GPS Plug

GPS Plug

Figure 5-46 GPS Plug Assembly


2. Assembly of the GPS Antenna Connector (for GPS models only)
a. Add a gradual 90 degree bend in the cable of the GPS antenna connector. The bend should
be in the same direction as the flat section of the threaded connector and should be after the
heat shrink tubing. Refer to Figure 5-47.

Heat Shrink Tubing

Flat Section of
Threaded Connector

Figure 5-47 Bend in the GPS Antenna Connector

6880309T86-C

November 14, 2007

5-30

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

b. Orient the GPS antenna connector as shown in Figure 5-48 and push the connector through
the opening in the chassis.
GPS Antenna Connector

Figure 5-48 GPS Antenna Connector Assembly


c.

5.7.5

Assemble the lock nut washer and the nut to the GPS antenna connector. Using a
5/16 socket driver, tighten the nut to 1.7 N-m (15 lbs-in).

Transceiver Board Reassembly


1. Insert the transceiver board into the chassis by tilting the transceiver board (approximately 30
degrees) and sliding it into place, taking care to line up the RF and DC connectors with the
openings in the back of the chassis.
Ensure that the transceiver board alignment holes are positioned over the chassis alignment
bosses and then push the board down to fully seat.
Locating Bosses

Figure 5-49 Placing the Transceiver Board in the Chassis

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

!
Caution

5-31

Do not leave the transceiver board in the chassis for extended periods of time
without the RF/DC retention clips, or damage to the board connectors may
occur.

NOTE: For GPS models, prior to the assembly of the transceiver board, position the cable of the GPS
antenna connector with the notch in the transceiver board, so that the cable will extend
through the transceiver board after the transceiver board is assembled. Then plug the GPS
antenna connector cable to the mating connector on the transceiver board. Refer to
Figure 5-50.
GPS Antenna
Connector Cable

Notch

Figure 5-50 Routing GPS Connector on to Transceiver Board

6880309T86-C

November 14, 2007

5-32

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

2. Insert the RF/DC retention clips and fully seat them. The DC clip should be inserted first to
properly locate the transceiver board. Refer to Figure 5-51.
RF/DC
Retention Clips

Figure 5-51 Inserting RF/DC Retention Clips


3. Insert the rear accessory connector into the radio assembly and press into place until the
connector is flushed with the chassis. Refer to Figure 5-52.
For GPS models only, place the GPS cap included on the accessory retainer on the GPS
antenna connector until it is fully seated.

Rear Accessory
Connector

Figure 5-52 Inserting Rear Accessory Connector

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-33

4. Place the PA pad on to the die cast cover by aligning the two holes in the PA pad with the
alignment pins on the die cast cover. For UHF models, refer to Figure 5-54.
For VHF models only: PA heat sink block and thermal pads need to be placed on to the
pressure pad before it gets assembled to the die cast cover. Refer to Figure 5-53 and
Figure 5-55.
a. Remove thermal pad (7571835M01) from the shipping liner and place it on to the heat
sink block by aligning the rounded corners. Remove the protective liner from the exposed
side of the thermal pad.
b. Insert the heat sink block with the thermal pad attached into the compartment on the PA
pressure pad, until it is fully seated. The attached thermal pad should be fully visible after
assembly.
c. Remove thermal pad (7571836M01) from the shipping liner and place it on to the exposed
metal surface of heat sink block by orienting the thermal pad so its shape matches the
opening on the pressure pad.
d. Remove the protective liner from the exposed side of the thermal pad (7571836M01).

Thermal Pad
(7571836M01)

VHF Pressure Pad

Heat Sink
(2671834M01)

Thermal Pad
(7571835M01)

Figure 5-53 Assembling of VHF PA Heat Sink System

6880309T86-C

November 14, 2007

5-34

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5. Fit the O-ring on to the die cast cover securely. Refer to either Figure 5-54 or Figure 5-55.

O-ring

PA Pad

Die Cast Cover

Figure 5-54 Assembling of PA Pad and O-ring (UHF models)

O-ring

PA Pad

Die Cast Cover

Figure 5-55 Assembling of PA Pad and O-ring (VHF models)

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-35

6. Place the die cast cover onto the chassis orienting the die cast cover so that screw holes 6
and 7 align with the bosses on the chassis as shown in Figure 5-56.

Screws (7)

Die Cast Cover

Radio Chassis

Figure 5-56 Assembling Die Cast Cover onto Chassis

6880309T86-C

November 14, 2007

5-36

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

7. Using a T20 TORX driver, tighten the seven screws between 2.94 N-m (26 lbs-in) in the
order shown in Figure 5-57.
8. Repeat tightening the seven screws in the order shown otherwise the first three screws will
likely be loose.

Figure 5-57 Screw Sequence to Tighten Die Cast Cover

5.7.6

Thermal Pad Replacement Procedure


A. Chassis Thermal Pad Replacement Procedure
Harmonic Filter Thermal Pad Replacement
1. Use a plastic flat-edge tool to lift the pad from the chassis surface. Discard the old pad.
2. Use a soft cloth to remove any remaining residue. Alcohol can also be used, if necessary.
Care should be taken to minimize any cleaning-agent contact with the surrounding shield
gasket.
3. Once the surface is clean and dry, remove the new pad from the shipping liner, and place it
white side down on the chassis as shown in Figure 5-58.
Harmonic Filter
Pad (7515579H01)
Harmonic Filter
Pad (7515580H01)

Radio Chassis

Figure 5-58 Replacing Thermal Pads


November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5-37

Driver Thermal pad Replacement


1. Use a plastic flat-edge tool to lift the pad from the chassis surface. Discard the old pad.
2. Use a soft cloth to remove any remaining residue. Alcohol can also be used, if necessary.
Care should be taken to minimize any cleaning-agent contact with the surrounding shield
gasket.
3. Once the surface is clean and dry, remove the new pad from the shipping liner, and place the
pad on to the chassis, aligning the edges of the pad with the edges of the chassis, as shown
in Figure 5-59.
Driver Pad
(7515357H01)

Radio Chassis

Figure 5-59 Aligning Driver Pad on Chassis


4. Apply even pressure to the pad and remove the protective liner.
B. Transceiver Board Thermal Pad Replacement Procedure
Transistor Thermal Pads and PA Thermal Pad Replacement
1. Use a plastic flat-edge tool to lift each pad from the transceiver board. Discard the old pads.
2. Use a soft cloth to remove any remaining residue. Alcohol can also be used, if necessary.
3. Once the surface is clean and dry, remove each new pad from the shipping liner, and place in
the proper location on top of each transistor component and the audio PA with the white side
down (see Figure 5-60).
Transistor
Thermal Pads
(7515582H01)

PA Thermal Pad (7515581H01)

Audio PA Component

Figure 5-60 Placing Thermal Pads on PA and Transistor Components

6880309T86-C

November 14, 2007

5-38

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

NOTE: See Section 5.7.8 for Option Board Reassembly procedure (Option Board Module Only).

5.7.7

Assemble Control Head and Decorative Cover to Radio Assembly


1. Assemble the mic jack pad, speaker pad, and control head O-ring seal on the radio as shown
in Figure 5-61.

Mic Jack Pad

Flex Connector

Control Head
O-ring Seal
Speaker Pad

Figure 5-61 Mic Jack Pad and Speaker Pad on Chassis


2. Verify that the flex cable is fully seated in connector on the control head assembly.
3. Assemble flex cable to the flex connector in the radio assembly, making sure it is fully seated.
4. Assemble the control head to the radio, applying pressure evenly across the entire control
head, so that all snap features engage at the same time.
5. Verify that the control head seal is not pinched and visible. If a pinch is found, disassemble
the control head, reseat the O-ring and reassemble the control head.
6. Refit the top cover over the assembled radio assembly. Press the cover down until it snaps
into place.

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

5.7.8

5-39

Option Board Module Reassembly


1. Fold the option flex along edge of the stiffener as shown in Figure 5-62.

Stiffener

Figure 5-62 Folding Option Flex


2. Mount option board on the radio chassis using four screws and tighten the screws using a
T6 TORX driver to 0.17 N-m (1.5 lbs-in). Refer to Figure 5-63.

Option Board

Radio Chassis

Screws (0386104Z04)
Figure 5-63 Assembling Option Board to Radio Chassis

6880309T86-C

November 14, 2007

5-40

Disassembly/Reassembly Procedures: Radio Reassembly Detailed

3. Assemble option flex (8415457H01) onto option board by aligning up 40-pin mating
connectors. Refer to Figure 5-64.

40-Pin Connectors

Option Board

Figure 5-64 Assembling Option Flex to Option Board


4. Firmly press the stiffener backing on the option flex until connectors are fully seated. Also
make sure option flex end gets fully inserted into 14-pin socket on the radio board. Refer to
Figure 5-65.

Option Flex
14-Pin Socket

Firmly Press Here


Stiffener
Figure 5-65 Inserting Option Flex End
NOTE: Regulatory Requirements
All MOTOTRBO radios are designed and engineered to meet all regulatory requirements for the
country or region of sale. Any option board designed for the MOTOTRBO Option Board ADK must
not compromise the regulatory compliance of the MOTOTRBO radio.
The 3rd party developer is responsible for providing all information, upon request by a regulatory
authority, in regards to any materials or substances used in the manufacture of an option board as it
pertains to its end-of-life.
Please review the terms of the MOTOTRBO License Agreement for more information on the
Licensed Developer or Application Partner responsibilities for regulatory compliance.
November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Exploded Mechanical Views and Parts Lists

5.8

Exploded Mechanical Views and Parts Lists

5.8.1

Radio Assembly Exploded View and Parts List

5-41

15

14

13

12

16

11

17
18
19

10
9
8
7

20
6
21

5
4

22

3
23
24
2

1
Figure 5-66 Radio Assembly Exploded View
6880309T86-C

November 14, 2007

5-42

Disassembly/Reassembly Procedures: Exploded Mechanical Views and Parts Lists

Table 5-3 Radio Exploded View Parts List


Item No.

Description

Part Number

Pad, Speaker Support

0716573H01

Pad, Mic Jack Support

0716572H01

O-Ring, Control Head

3216200H01

Chassis, Die Cast

2715587H06

Pad, Driver

7515357H01

GPS Antenna Connector

3015953H01

Pads, Transistor Thermal (Qty:3)

7515582H01

Pad, PA Thermal

7515581H01

PCB, Transceiver

See Sections 1.5


through 1.8 to identify
proper board.

10

Pad, VHF Pressure


Pad, UHF Pressure

7515605H01
7515538H01

11

O-Ring, Main

3215586H01

12

Cover, Die Cast

1515588H04

13

O-Rings, Screw (Qty:7)

3216871H01

14

Screws (Qty:7)

0371274L02

15

Cover, Decorative

1516006H01

16

Pad Thermal (VHF models only)

7571835M01

17

Heat Sink, Aluminium (VHF models only)

2671834M01

18

Pad, Thermal (VHF models only)

7571836M01

19

Clips, RF/DC Retention (Qty:2)

4285702E01

20

GPS Cap

3216338H01

21

GPS Plug

3216339H01

22

Rear Accessory Connector

0178042A01

23

Pad, Harmonic Filter

7515579H01

24

Pad, Harmonic Filter

7515580H01

November 14, 2007

6880309T86-C

Disassembly/Reassembly Procedures: Exploded Mechanical Views and Parts Lists

5.8.2

5-43

Control Head Exploded Views and Parts Lists


8
9

7
6
5
4

10

3
2

1
11

12

13

Figure 5-67 Display Control Head Exploded View


Table 5-4 Display Control Head (PMLN4759_) Exploded View Parts List
Item no

6880309T86-C

Description

Part No

Volume Knob Assembly

3616060H01

Housing Assembly

0115670H01

LCD Display Module

7215559H01

Keypad Assembly

7515521H01

Indicator Light Guide Holder

0715537H01

Indicator Light Guide

6115536H01

Mic Jack Seal

3264133H01

PCB Assembly

0104020J68

Control Head Flex Cable

3015638H01

10

Screws

0371370L01

11

Speaker Retainer

4215135H01

12

Speaker

5015134H02

13

Radio Model Nameplate for DGM 6100


Radio Model Nameplate for DGM 6100+

3316323H09
3316323H15

November 14, 2007

5-44

Disassembly/Reassembly Procedures: Exploded Mechanical Views and Parts Lists

9
8

10

7
6

11

5
4
3
2

12
1
13

14
15

16

Figure 5-68 Numeric Display Control Head Exploded View


Table 5-5 Numeric Display Control Head (PMLN4967_) Exploded View Parts List
Item no

November 14, 2007

Description

Part No

Volume Knob Assembly

3616060H01

Housing Assembly

0171214L01

Icon Light Guide Holder

0771089L01

Keypad Assembly

7571162L01

Indicator Light Guide Holder

0715537H01

Indicator Light Guide

6115536H01

Mic Jack Seal

3264133H01

LED Display

7216958H01

PCB Assembly

0104022J64

10

Control Head Flex Cable

3015638H01

11

Screws

0371370L01

12

LED Display Spacer

4371389L01

13

Speaker Retainer

4215135H01

14

Icon Light Guide

6171088L01

15

Speaker

5015134H02

16

Radio Model Nameplate for DGM 4100


Radio Model Nameplate for DGM 4100+

3316323H10
3316323H16

6880309T86-C

Disassembly/Reassembly Procedures: Torque Chart

5.9

5-45

Torque Chart
Table 5-6 lists the various nuts and screws by part number and description, followed by the torque
values in different units of measure. Torque all screws to the recommended value when assembling
the radio.
Table 5-6 Torque Specifications for Nuts and Screws
Part
Number

Description

Driver/ Socket

Torque
N-m

lbs-in

kg-cm

3015953H01

GPS Antenna Connector

5/16 socket driver

1.7

15

17

0371370L01

Screw, M3x1.34, Pan Head

T10 Torx

0.88

7.8

9.0

0371274L02

Screw, M4x0.7, Pan Head

T20 Torx

2.94

26

30.0

0386104Z04

Screw, M2x0.4, Pan Head

T6 Torx

0.17

1.5

1.73

6880309T86-C

November 14, 2007

5-46

Disassembly/Reassembly Procedures: Torque Chart

Notes

November 14, 2007

6880309T86-C

Chapter 6 Basic Troubleshooting

6.1

Introduction
This chapter contains error codes and board replacement procedures. This section can help you
isolate a problem to the board level. If the radio does not pass all the performance checks in
Chapter 3 or exhibits an error code listed below, then the circuit board should be replaced. Please
send the radio to a Motorola Service Center listed in Appendix B.
NOTE: To access the various connector pins, use the housing eliminator/test fixture along with the
diagrams found in this section of the manual. (See Section, "Service Aids" on page 2-2, for
the appropriate Motorola service aids and tools part numbers.)

6.1.1

High Power RF Precaution

!
Caution

6.2

The radio might transmit while the technician believes the radio is in receive
mode under the following conditions: radio failure, digital affiliation, a
defective PTT button, or other unintentional activations.
To avoid possible equipment damage, when performing both transmit and
receive tests, a suitable attenuator rated at 100 W or more should always be
used with test equipment connected to the RF connector. The only
exception to this is when the equipments input power rating is higher than
the maximum output power of the radio.

Replacement Service Kit Procedures


Once a problem has been isolated to a specific board, install the appropriate service kit (see Model
Charts in section 1.5 on page 1-5 through section 1.8 on page 1-6), which is orderable from Motorola
Online.
Refer to http://www.motorola.com/businessonline for further information.
If a board is replaced, it does not necessarily need to be retuned if it has been factory tuned. It
should however be checked for performance before being placed into service. Of particular concern
is the Bias DAC, which will need to be set for the appropriate final device bias current prior to keying
up the radio. If the bias is not properly set it may be possible to cause damage to the transmitter.

!
Caution

The Tuner Tool only allows the serial number of a blank board to be entered
once. Be very attentive during this procedure.

6-2

6.3

Basic Troubleshooting: Power-Up Error Codes

Power-Up Error Codes


When the radio is turned on (power-up), the radio performs cursory tests to determine if its basic
electronics and software are in working order. Problems detected during these tests are presented
as error codes on the radios display. The presence of an error should prompt the user that a
problem exists and that a service technician should be contacted.
Self-test errors are classified as either fatal or non-fatal. Fatal errors inhibit user operation; non-fatal
errors do not. Use the following tables to aid in understanding particular power-up error code
displays.
Table 6-1 Power-Up Error Codes
Error Code

Description

Error Type

Corrective Action

ERROR 01/02

FLASH ROM Codeplug


Checksum

NON-FATAL

Reprogram the codeplug.

ERROR 01/7E

Peripheral device non-fatal


error

NON-FATAL

Re-connect the peripheral device.

ERROR 01/7F

Peripheral device fatal error FATAL

Replace the peripheral device.

ERROR 01/22

Tuning Codeplug
Checksum

NON-FATAL

Reprogram the tuning partition.

FAIL 01/81

FLASH ROM Checksum

FATAL

Reprogram the radio firmware.

FAIL 01/82

FLASH ROM Codeplug


Checksum

FATAL

Reprogram the codeplug.

FAIL 01/88

External SRAM Failure

FATAL

Turn the radio off, then on.

FAIL 01/90

General Hardware

FATAL

Turn the radio off, then on.

FAIL 01/92

Security Partition
Checksum

FATAL

Reprogram the security partition.

FAIL 01/93

FlashPORT AUTHENT
CODE Failure

FATAL

Contact the depot.

FAIL 01/A2

Tuning Codeplug
Checksum

FATAL

Reprogram the tuning partition.

FAIL 02/81

DSP ROM Checksum

FATAL

Reprogram the DSP firmware.

FAIL 02/88

DSP RAM Fatal Error

FATAL

Turn the radio off, then on.

FAIL 02/90

General DSP Hardware


Failure

FATAL

Turn the radio off, then on.

FAIL 01/A0

Back End Receiver IC


Failure

FATAL

Turn the radio off, then on. Send


radio to the nearest Motorola
Depot.

FAIL 02/C0

DSP Internal RAM Fatal


Error

FATAL

Turn the radio off, then on. Send


radio to the nearest Motorola
Depot.

November 14, 2007

6880309T86-C

Basic Troubleshooting: Operational Error Codes

6.4

6-3

Operational Error Codes


During radio operation, the radio performs dynamic tests to determine if the radio is working properly.
Problems detected during these tests are presented as error codes on the radios display. The
presence of an error code should prompt a user that a problem exists and that a service technician
should be contacted. Use Table 6-2 to aid in understanding particular operational error codes.
Table 6-2 Operational Error Codes
Error Code

Description

Error Type

Corrective Action

FAIL 001

Synthesizer Out-of-Lock

NON-FATAL

1. Reprogram the codeplug.


2. Send radio to the nearest
Motorola Depot.

FAIL 002

Personality checksum or
system block error

NON-FATAL

Reprogram the codeplug.

6880309T86-C

November 14, 2007

6-4

Basic Troubleshooting: Operational Error Codes

Notes

November 14, 2007

6880309T86-C

Chapter 7 Accessories

7.1

Introduction
Motorola provides the following approved accessories to improve the productivity of your digital
mobile two-way radio.
For a list of Motorola-approved antennas, and other accessories, visit the following web site:
http://www.motorola.com/governmentandenterprise

7.1.1

7.1.2

7.1.3

Audio
Part No.

Description

HMN4098_

Telephone Style Handset

RMN5050_

Desktop Microphone

RMN5052_

Compact Microphone

RMN5053_

Heavy Duty Microphone with Enhanced Audio

RMN5054_

Visor Microphone with Enhanced Audio

RMN5065_

Keypad Microphone with Enhanced Audio

Speakers
Part No.

Description

RSN4002_

13 Watt External Speaker

RSN4003_

7.5 Watt External Speaker

RSN4004_

5 Watt External Speaker

Desktop Accessories
Part No.

Description

GLN7318_

Desktop Tray without Speaker

RSN4005_

Desktop Tray with Speaker

GPN6145_

Switchmode Power Supply (1-25 Watt Models)(CE marked)

GKN6266_

Radio Power Cable for GPN6145

HPN4007_

Power Supply and Cable (25-60 Watt Models)

HPN4008_

Power Supply and Cable (1-25 Watt Models)

NTN7373_R

US Line Cord

NTN7374_R

Euro Line Cord

NTN7375_R

UK Line Cord

NTN9246_

Argentina Line Cord

HKN9088_

Mobile Mini-U Antenna Adaptor, 8-foot Cable

PMLN5072_

Hardware Kit for Rear Accessory Connector

7-2

7.1.4

7.1.5

7.1.6

Accessories: Introduction

Mounting Kits
Part No.

Description

RLN5933_

In Dash (DIN) Mounting Kit

RLN6077_

Low Profile Trunnion Kit

RLN6078_

High Profile Trunnion KIt

RLN6079_

Key Lock Trunnion Kit

Cables
Part No.

Description

HKN4137_

Power Cable to Battery, 3m (10 ft.), 15 amp (1-25W)

HKN4191_

Power Cable to Battery, 3m (10 ft.), 20 amp (1-45W)

HKN4192_

Power Cable to Battery, 6m (20 ft.), 20 amp (1-45W)

HKN6184_

Mobile Front Programming Cable

PMKN4010_

Mobile & Repeater Rear Programming Cable

PMKN4016_

Mobile & Repeater Rear Accessory Programming and Test


Cable

PMKN4018_

Mobile & Repeater Rear Accessory Connector Universal


Cable

RKN4136_

Ignition Sense Cable

Antennas
Part No.

Description

HAD4006_

VHF, 136-144 MHz, 1/4 Wave, Through-hole Mount, Mini-U

HAD4007_

VHF, 146-150.8 MHz, 1/4 Wave, Through-hole Mount, Mini-U

HAD4008_

VHF, 150.8-162 MHz, 1/4 Wave, Through-hole Mount, Mini-U

HAD4009_

VHF, 162-174 MHz, 1/4 Wave, Through-hole Mount, Mini-U

HAD4014_

VHF, 146-172 MHz, 3.0 dB Gain, Through-hole Mount, Mini-U

HAE4002_

UHF, 403-430 MHz, 1/ 4 Wave, Through-hole Mount, Mini-U

HAE4003_

UHF, 450-470 MHz, 1/ 4 Wave, Through-hole Mount, Mini-U

HAE4010_

UHF, 406-420 MHz, 3.5 dB Gain, Through-hole Mount, Mini-U

HAE4011_

UHF, 450-470 MHz, 3.5 dB Gain, Through-hole Mount, Mini-U

RAE4004_

UHF, 450-470 MHz, 5.0 dB Gain, Through-hole Mount, Mini-U

November 14, 2007

6880309T86-C

Accessories: Introduction

7-3

For DGM 4100+/DGM 6100+ GPS Models only:


RAD4214_

Combination GPS/VHF 136-144 MHz, 1/4 Wave,


Through-hole Mount, Mini-U

RAD4215_

Combination GPS/VHF 146-150.8 MHz, 1/4 Wave,


Through-hole Mount, Mini-U

RAD4216_

Combination GPS/VHF 150.8-162 MHz, 1/4 Wave,


Through-hole Mount, Mini-U

RAD4217_

Combination GPS/VHF 162-174 MHz, 1/4 Wave,


Through-hole Mount, Mini-U

RAD4218_

Combination GPS/VHF 146-172 MHz, 3.0 dB Gain,


Through-hole Mount, Mini-U

PMAE4030_

Combination GPS/UHF 403-430 MHz, 1/4 Wave,


Through-hole Mount, Mini-U

PMAE4031_

Combination GPS/UHF 450-470 MHz, 1/4 Wave,


Through-hole Mount, Mini-U

PMAE4032_

Combination GPS/UHF 406-420 MHz, 3.5 dB Gain,


Through-hole Mount, Mini-U

PMAE4033_

Combination GPS/UHF 450-470 MHz, 3.5 dB Gain,


Through-hole Mount, Mini-U

PMAE4034_

Combination GPS/UHF 450-470 MHz, 5.0 dB Gain,


Through-hole Mount, Mini-U

PMAN4000_

Fixed Mount GPS Active Antenna

PMAN4001_

Window Mount GPS Active Antenna

PMAN4002_

Magnetic Mount GPS Active Antenna

Replacement Antennas for DGM 4100+/DGM 6100+ GPS Models only:


RAD4223_

Kit, Antenna VHF 162-174 MHz, 1/4 Wave

RAD4224_

Kit, Antenna VHF 150.8-162 MHz, 1/4 Wave

RAD4225_

Kit, Antenna VHF 146-150.8 MHz, 1/4 Wave

RAD4226_

Kit, Antenna VHF 136-144 MHz, 1/4 Wave

RAD4227_

Kit, Antenna VHF 146-172 MHz, 3.0 dB Gain

PMAE4039_

Kit, Antenna UHF 403-430 MHz, 1/4 Wave

PMAE4040_

Kit, Antenna UHF 406-420 MHz, 3.5 dB Gain

PMAE4041_

Kit, Antenna UHF 450-470 MHz, 1/4 Wave

PMAE4042_

Kit, Antenna UHF 450-470 MHz, 3.5 dB Gain

PMAE4043_

Kit, Antenna UHF 450-470 MHz, 5.0 dB Gain

PMAN4004_

Kit, Combo GPS+RF, Base Only, Through-hole Mount, Mini-U

6880309T86-C

November 14, 2007

7-4

7.1.7

7.1.8

Accessories: Introduction

Miscellaneous Accessories
Part No.

Description

HKN9557_

PL259/Mini-U Antenna Adaptor, 8-foot Cable

HLN7001_

Option Board Interface Kit

HLN9073_

Microphone Hang-up Clip (All Microphones)

HLN9414_

Universal Microphone Hang-up Clip (All Microphones)

RLN5926_

Push Button PTT

RLN5929_

Emergency Footswitch

Replacement Button Parts and Kits


Part No.

Description

7515562H02

Button - P1

7515562H03

Button - P2

7515562H04

Button - P3

7515562H05

Button - P4

7515562H06

Button - Emergency

7515562H07

Button - Talkaround

7515562H08

Button - Low/High

7515562H09

Button - Scan

7515562H10

Button - Monitor

7515562H11

Button - Group Call

7515562H12

Button - Text Message

7515562H13

Button - VOX

7515562H14

Button - Backlight

7515562H15

Button - Remote Monitor

7515562H16

Button - Radio Kill

7515562H17

Button - Radio Check

7515562H18

Button - Phone

7515562H19

Button - Aux1

7515562H20

Button - Aux2

November 14, 2007

Button

6880309T86-C

Accessories: Introduction

7-5

7515562H21

Button -H&L (Horn and Lights)

7515562H22

Button - Option Board

7515562H23

Button - Zone

7515562H24

Button - Scrambling

7515562H25

Button - Orange

7515562H26

Button - Contacts

7515562H27

Button - Radio Check 2

HKLN4289_

Display Mobile Button Kit (Includes buttons for Monitor, Scan,


Backlight and Talkaround.)

HKLN4290_

Numeric Display Mobile Button Kit (Includes buttons for


Monitor, Scan, Backlight, and Talkaround.)

HKLN4291_

Display Mobile Button Kit (Includes buttons for Monitor, Scan,


Backlight, Emergency, Talkaround, Text Message and
Contacts)

HKLN4292_

Mobile Button Kit (Includes buttons for Remote Monitor,


Radio Check, Radio Disable and VOX)

HKLN4293_

Numeric Display Mobile Button Kit (Includes buttons for


Monitor and Scan)

PMLN5070_

Display Mobile Navigation Button Replacement Kit (Includes


Left and Right navigation, OK, Menu and Back buttons)

PMLN5071_

Mobile Option Button Standard Replacement Kit (Includes


P1, P2, P3 and P4 buttons)

6880309T86-C

November 14, 2007

7-6

Accessories: Introduction

Notes

November 14, 2007

6880309T86-C

Appendix A

A.1

Replacement Parts Ordering

Basic Ordering Information


When ordering replacement parts or equipment information, the complete identification number
should be included. This applies to all components, kits, and chassis. If the component part number
is not known, the order should include the number of the chassis or kit of which it is a part, and
sufficient description of the desired component to identify it.

A.2

Motorola Online
Motorola Online users can access our online catalog at http://www.motorola.com/businessonline
To register for online access:
Have your Motorola Customer number available.
Please go to http://www.motorola.com/businessonline and click on Sign Up Now.
Complete form and submit it.
Contact your BDM to complete set-up and it will be done within 24 to 48 hours.

A-2

Replacement Parts Ordering: Motorola Online

Notes

November 14, 2007

6880309T86-C

Appendix B

B.1

Motorola Service Centers

Servicing Information
If a unit requires further complete testing, knowledge and/or details of component level
troubleshooting or service than is customarily performed at the basic level, please send the radio to
a Motorola Service Center as listed below.

B.2

Motorola de Mxico, S.A.


Bosques de Alisos 125
Col. Bosques de las Lomas CP 05120
Mxico D.F.
Mxico
Tel: (5) 257-6700

B.3

Motorola de Colombia, Ltd.


Carrera 7 No. 71-52
Bogota - Colombia
Tel: (571) 376-6990

B-2

Motorola Service Centers: Motorola de Colombia, Ltd.

Notes

November 14, 2007

6880309T86-C

Glossary

Glossary

This glossary contains an alphabetical listing of terms and their definitions that are applicable to
portable and mobile subscriber radio products. All terms do not necessarily apply to all radios, and
some terms are merely generic in nature.

Term

Definition

Analog

Refers to a continuously variable signal or a circuit or device designed to


handle such signals.

Band

Frequencies allowed for a specific purpose.

CPS

Customer Programming Software: Software with a graphical user interface


containing the feature set of a radio.

Default

A pre-defined set of parameters.

DGM

Refers to Digital Professional Radio model names in the MOTOTRBO


Professional Digital Two-Way Radio System.

Digital

Refers to data that is stored or transmitted as a sequence of discrete symbols


from a finite set; most commonly this means binary data represented using
electronic or electromagnetic signals.

DPL

Digital Private-Line: A type of digital communications that utilizes privacy call,


as well as memory channel and busy channel lock out to enhance
communication efficiency.

FCC

Federal Communications Commission.

Frequency

Number of times a complete electromagnetic-wave cycle occurs in a fixed unit


of time (usually one second).

GPIO

General-Purpose Input/Output.

GPS

Global Positioning System.

IC

Integrated Circuit: An assembly of interconnected components on a small


semiconductor chip, usually made of silicon. One chip can contain millions of
microscopic components and perform many functions.

IF

Intermediate Frequency.

kHz

kilohertz: One thousand cycles per second. Used especially as a radiofrequency unit.

LCD

Liquid-Crystal Display: An LCD uses two sheets of polarizing material with a


liquid-crystal solution between them. An electric current passed through the
liquid causes the crystals to align so that light cannot pass through them.

LED

Light Emitting Diode: An electronic device that lights up when electricity is


passed through it.

MDC

Motorola Digital Communications.

Glossary-2

Term

Definition

MHz

Megahertz: One million cycles per second. Used especially as a radiofrequency unit.

Paging

One-way communication that alerts the receiver to retrieve a message.

PC Board

Printed Circuit Board. Also referred to as a PCB.

PL

Private-Line Tone Squelch: A continuous sub-audible tone that is transmitted


along with the carrier.

Programming Cable

A cable that allows the CPS to communicate directly with the radio using USB.

Receiver

Electronic device that amplifies RF signals. A receiver separates the audio


signal from the RF carrier, amplifies it, and converts it back to the original
sound waves.

Repeater

Remote transmit/receive facility that re-transmits received signals in order to


improve communications range and coverage (conventional operation).

RF

Radio Frequency: The portion of the electromagnetic spectrum between audio


sound and infrared light (approximately 10 kHz to 10 GHz).

RX

Receive.

Signal

An electrically transmitted electromagnetic wave.

Spectrum

Frequency range within which radiation has specific characteristics.

Squelch

Muting of audio circuits when received signal levels fall below a pre-determined
value. With carrier squelch, all channel activity that exceeds the radios preset
squelch level can be heard.

TOT

Time-out Timer: A timer that limits the length of a transmission.

TPL

Tone Private Line.

Transceiver

Transmitter-receiver. A device that both transmits and receives analog or digital


signals. Also abbreviated as XCVR.

Transmitter

Electronic equipment that generates and amplifies an RF carrier signal,


modulates the signal, and then radiates it into space.

TX

Transmit.

UHF

Ultra-High Frequency.

USB

Universal Serial Bus: An external bus standard that supports data transfer rates
of 12 Mbps.

VHF

Very High Frequency.

VIP

Vehicle Interface Port.

November 14, 2007

6880309T86-C

Motorola, Inc.
1301 E. Algonquin Rd.
Schaumburg, IL 60196-1078, U.S.A.
MOTOROLA and the Stylized M Logo are
registered in the U.S. Patent and Trademark Office.
All other product or service names are the property
of their respective owners.
2007 Motorola, Inc.
All rights reserved. Printed in the U.S.A.
November 2007.
www.motorola.com/radiosolutions

*6880309T86*
6880309T86-C

You might also like