Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 35 views

    Installation Data For: 250 & 375 Series Point Gate Needle

    Uploaded by

    Esteban Vanegas Alvarez
    This document provides installation instructions and safety information for 250 and 375 series point gate needles. It lists the available needle models with their specifications, including needle length, tip diameter, thread type, and compatible tip sub-assembly. Instructions are given for cleaning, installing, and torquing the needle and heater assembly. Safety warnings advise of electrical, temperature, and pressure hazards and proper protective equipment needed when operating the hot runner system.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Installation Data For: 250 & 375 Series Point Gate Needle

    Uploaded by

    Esteban Vanegas Alvarez
    35 views2 pages
    This document provides installation instructions and safety information for 250 and 375 series point gate needles. It lists the available needle models with their specifications, including needle length, tip diameter, thread type, and compatible tip sub-assembly. Instructions are given for cleaning, installing, and torquing the needle and heater assembly. Safety warnings advise of electrical, temperature, and pressure hazards and proper protective equipment needed when operating the hot runner system.

    Original Description:

    mE

    Original Title

    ME-0741-PS-531

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides installation instructions and safety information for 250 and 375 series point gate needles. It lists the available needle models with their specifications, including needle length, tip diameter, thread type, and compatible tip sub-assembly. Instructions are given for cleaning, installing, and torquing the needle and heater assembly. Safety warnings advise of electrical, temperature, and pressure hazards and proper protective equipment needed when operating the hot runner system.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    35 views2 pages

    Installation Data For: 250 & 375 Series Point Gate Needle

    Uploaded by

    Esteban Vanegas Alvarez
    This document provides installation instructions and safety information for 250 and 375 series point gate needles. It lists the available needle models with their specifications, including needle length, tip diameter, thread type, and compatible tip sub-assembly. Instructions are given for cleaning, installing, and torquing the needle and heater assembly. Safety warnings advise of electrical, temperature, and pressure hazards and proper protective equipment needed when operating the hot runner system.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ME-0741-PS-531-D

    09-09

    ETH9997

    INSTALLATION DATA
    For: 250 & 375 SERIES POINT GATE NEEDLE
    Please read carefully before installing components.

    NOTE: Dimensions are shown in Inches.

    NEEDLE LENGTH

    THREAD

    BODY

    HEATER
    TIP
    NEEDLE

    POINT GATE NEEDLE


    CATALOG NUMBER
    *EHN0015
    EHN0300
    *EHN0016
    EHN0301

    NEEDLE TIP
    DIAMETER

    NEEDLE TIP DIAMETER

    NEEDLE LENGTH

    THREAD
    1/2-24

    0.010

    1.680

    * EHN0015 and EHN0016 needles NOT recommended for abrasive materials.

    5/8-20

    USED WITH
    TIP SUB-ASSEMBLY
    CATALOG NUMBER
    EHT0005 (250 SERIES)
    EHT0302 (250 SERIES)
    EHT0039 (375 SERIES)
    EHT0303 (375 SERIES)

    ME-0741-PS-531-D

    09-09

    ETH9997

    INSTALLATION DATA
    For: 250 & 375 SERIES POINT GATE NEEDLE
    Please read carefully before installing components.

    RECOMMENDATIONS AND GUIDELINES


    1.

    Nozzle (multiple-applications) body must be cleaned


    of any material in the seal off area and threaded areas
    before reassembling.

    2.

    Careful attention should be taken to the needle as damage


    could occur if needle is dropped or strikes a rigid material.
    Treat needle like a glass or ceramic material.

    3.

    Apply an anti-sieze compound on the tip threads.

    4.

    Tip must be torqued into the nozzle body using 30 5 ft-lbs.


    When reassembling. For protection of the needle point, a six
    point deep well socket is recommended.

    5.

    Careful attention should be taken to the heater/thermocouple


    leads as damage could occur when working on nozzle or
    bushing assembly.

    6.

    Seal ring for nozzle body must be replaced each time nozzle
    body and/ or manifold are removed to ensure seal off.

    7.

    Wait a minimum of 5 minutes after set point has been achieved


    for suffient heat to transfer into the needle before molding.

    IMPORTANT SAFETY INFORMATION


    A hot-runner system includes electrical elements and may contain molten
    plastic at elevated temperature and pressure. To avoid injury, exercise
    caution by reading these instructions before servicing or operating the
    system.
    These instructions must be passed on to the end user where they should
    be read before using this product. Failure to do so can result in serious
    injury or death.

    DANGER
    Failure to comply will result in serious injury or death:
    ELECTRICAL HAZARDS
    Improper voltages or grounding can result in electrical shock. Use only
    with proper voltage and a proper earth ground.
    To avoid electrical shock, do not operate product when wet.
    Do not operate this equipment with covers or panels removed.
    To avoid electrical shock, turn off main power disconnect and lockout /
    tag out before servicing this device. Do not connect temperature sensors to
    electrical power. It will damage the product and it can cause fire, severe
    injuries or even death.
    If green ground wire present wire must be connected to the ground.
    Do not rebend rigid leads. Rebending leads might result in damage to circuit.
    Product might absorb moisture when cool. Use low Voltage or power to drive
    out residual moisture before applying full power. Failure to do so may cause
    damage to this product.

    WARNING
    Failure to comply can result in serious injury or death:
    STORED ENERGY AND HIGH TEMPERATURE HAZARDS
    This product maintains molten plastic at high pressure. Use caution when
    operating and servicing the system.
    Physical contact with molten plastic may result in severe burns. Proper
    protective equipment, including eye protection, must be worn. This product
    has heated surfaces. Use caution when operating and servicing the system
    to avoid severe burns. Proper protective equipment should be worn.

    DME COMPANY LLC


    DME SHALL NOT BE LIABLE FOR MISUSE OR FAILURE TO FOLLOW THE ENCLOSED
    INSTRUCTIONS AND SPECIFICATIONS. D-M-E HERBY TO DISCLAIMS ALL IMPLIED
    WARRANTIES, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR
    PURPOSE. IN NO EVENT SHALL D-M-E BE RESPONSIBLE FOR LOSS OF USE, REVENUE
    OR PROFIT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGED.

    29111 STEPHENSON HIGHWAY


    MADISON HEIGHTS
    MICHIGAN 48071 USA
    US 800-656-6656
    CANADA 800-387-6600
    www.dme.net

    You might also like