Sap kr97
Sap kr97
Sap kr97
SAP-KR97EHAXB + SAP-CR97EHAXB
SAP-KR127EHAXB + SAP-CR127EHAXB
FILE NO.
Destination: Europe (50Hz)
SAP-KR127EHAXB
1 852 351 36
SAP-KR97EHAXB
1 852 351 35
1 852 351 31
SAP-CR127EHAXB
Indoor Unit
1 852 351 32
Outdoor Unit
SAP-KR97EHAXB
SAP-KR127EHAXB
SAP-CR97EHAXB
SAP-CR127EHAXB
RoHS
This product does not contain any hazardous substances prohibited by the RoHS Directive.
WARNING
You are requested to use RoHS compliant parts for maintenance or repair.
You are requested to use lead-free solder.
Important!
Please Read Before Starting
When Transporting
Be careful when picking up and moving the indoor and
outdoor units. Get a partner to help, and bend your knees
when lifting to reduce strain on your back. Sharp edges or
thin aluminum fins on the air conditioner can cut your
fingers.
When Installing
CAUTION
In a Ceiling or Wall
Make sure the ceiling/wall is strong enough to hold the
units weight. It may be necessary to construct a strong
wood or metal frame to provide added support.
In a Room
Properly insulate any tubing run inside a room to prevent
"sweating" that can cause dripping and water damage to
walls and floors.
In Moist or Uneven Locations
Use a raised concrete pad or concrete blocks to provide a
solid, level foundation for the outdoor unit. This prevents
water damage and abnormal vibration.
In an Area with High Winds
Securely anchor the outdoor unit down with bolts and a
metal frame. Provide a suitable air baffle.
In a Snowy Area (for Heat Pump-type Systems)
Install the outdoor unit on a raised platform that is higher
than drifting snow. Provide snow vents.
SPECIAL PRECAUTIONS
WARNING
When Servicing
When Wiring
Turn the power off at the main power box (mains) before
opening the unit to check or repair electrical parts and
wiring.
Keep your fingers and clothing away from any moving
parts.
Clean up the site after you finish, remembering to check
that no metal scraps or bits of wiring have been left
inside the unit being serviced.
Others
CAUTION
Ventilate any enclosed areas when installing or testing
the refrigeration system. Escaped refrigerant gas, on
contact with fire or heat, can produce dangerously toxic
gas.
Confirm upon completing installation that no refrigerant
gas is leaking. If escaped gas comes in contact with a
stove, gas water heater, electric room heater or other
heat source, it can produce dangerously toxic gas.
Table of Contents
Page
1. OPERATING RANGE ...................................................................................................................
2. SPECIFICATIONS
2-1. Unit Specifications .............................................................................................................
2-2. Major Component Specifications .......................................................................................
2-3. Other Component Specifications .......................................................................................
6
8
12
3. DIMENSIONAL DATA.....................................................................................................................
13
16
5. PERFORMANCE DATA
5-1. Performance charts ............................................................................................................
5-2. Air Throw Distance Charts .................................................................................................
5-3. Cooling Capacity ................................................................................................................
5-4. Heating Capacity ................................................................................................................
17
19
21
23
6. ELECTRICAL DATA
6-1. Electrical Characteristics ....................................................................................................
6-2. Electric Wiring Diagrams ....................................................................................................
24
26
7. INSTALLATION INSTRUCTIONS
7-1. Installation Site Selection ...................................................................................................
7-2. Recommended Wire Length and Diameter ........................................................................
7-3. Remote Control Unit Installation Position ...........................................................................
7-4. How to Test Run the Air Conditioner ...................................................................................
7-5. Removing and Installing the Grille ......................................................................................
7-6. Address Setting of the Remote Control Unit .......................................................................
28
30
31
32
33
34
8. FUNCTIONS
8-1. Room Temperature Control ................................................................................................
8-2. Dry Operation (Dehumidification) .......................................................................................
8-3. Automatic Switching between Cooling and Heating ...........................................................
8-4. Freeze Prevention (Cooling and Dry) .................................................................................
8-5. Cold Draft Prevention (Heating) .........................................................................................
8-6. Overload Prevention (Heating) ...........................................................................................
8-7. Automatic Fan Speed (Cooling, Dry and Heating) ..............................................................
8-8. Defrosting Operation (Heating) ...........................................................................................
35
37
38
39
40
41
42
43
Page
9. TROUBLESHOOTING
9-1. Check before and after troubleshooting ................................................................................
9-2. Air conditioner does not operate. ...........................................................................................
9-3. Some part of air conditioner does not operate. .....................................................................
9-4. Air conditioner operates, but abnormalities are observed. ....................................................
45
46
50
52
54
54
56
56
57
59
60
60
61
62
62
APPENDIX
63
1. OPERATING RANGE
Temperature
Cooling
Heating
Maximum
Minimum
Maximum
Minimum
32 C D.B. / 23 C W.B.
19 C D.B. / 14 C W.B.
27 C D.B.
24 C D.B. / 18 C W.B.
-8 C D.B. / -9 C W.B.
16 C D.B.
2. SPECIFICATIONS
2-1. Unit Specifications
Indoor Unit
Outdoor Unit
SAP-KR97EHAXB
SAP-CR97EHAXB
Power Source
Voltage Rating
230V
Performance
Capacity
Air Circulation (High)
Moisture Removal (High)
Indoor / Outdoor
Electrical Rating
Available Voltage Range
Running Amperes
Power Input
Power Factor
E.E.R.
C.O.P.
Compressor Locked Rotor Amperes
Features
Controls / Temperature Control
Control Unit
Timer
Fan Speeds
Airflow Direction (Indoor)
V
A
W
%
W/W
W/W
A
Package Dimensions
Weight
Shipping Volume
Height
Width
Depth
Height
Width
Depth
Net
Shipping
Cooling
2.8
9,600
600 / 1,550
1.5
Heating
2.8
9,600
600 / 1,490
-
Cooling
Heating
3.9
870
97
3.22
16.5
198 to 264
3.5
775
96
3.61
16.5
Indoor / Outdoor
Horizontal
Vertical
Air Filter
Compressor
Refrigerant / Amount charged at shipment
Refrigerant Control
Operation Sound
Indoor : Hi/Me/Lo/Qt*
(*Qt = Quiet mode)
Outdoor : Hi
Refrigerant Tubing Connections
Max. allowable tubing length at shipment
Refrigerant
Narrow tube
Tube Diameter
Wide tube
Refrigerant Tube Kit / Accessories
Dimensions & Weight
Unit Dimensions
kW
BTU/h
m3/h
Liters/h
kg
dB-A
dB-A
m
mm (in.)
mm (in.)
Indoor Unit
250
799
205
270
870
295
7.5
9.0
0.06
mm
mm
mm
mm
mm
mm
kg
kg
m3
Outdoor Unit
510
660
240
558
769
340
27
28
0.14
Indoor Unit
Outdoor Unit
SAP-KR127EHAXB
SAP-CR127EHAXB
Power Source
Voltage Rating
230V
Performance
Capacity
Air Circulation (High)
Moisture Removal (High)
Indoor / Outdoor
Electrical Rating
Available Voltage Range
Running Amperes
Power Input
Power Factor
E.E.R.
C.O.P.
Compressor Locked Rotor Amperes
Features
Controls / Temperature Control
Control Unit
Timer
Fan Speeds
Airflow Direction (Indoor)
V
A
W
%
W/W
W/W
A
Package Dimensions
Weight
Shipping Volume
Height
Width
Depth
Height
Width
Depth
Net
Shipping
Cooling
3.3
11,300
610 / 1,500
2.3
Heating
3.6
12,300
640 / 1,440
-
Cooling
Heating
4.6
1,025
97
3.22
28.0
198 to 264
4.5
995
96
3.62
28.0
Indoor / Outdoor
Horizontal
Vertical
Air Filter
Compressor
Refrigerant / Amount charged at shipment
Refrigerant Control
Operation Sound
Indoor : Hi/Me/Lo/Qt*
(*Qt = Quiet mode)
Outdoor : Hi
Refrigerant Tubing Connections
Max. allowable tubing length at shipment
Refrigerant
Narrow tube
Tube Diameter
Wide tube
Refrigerant Tube Kit / Accessories
Dimensions & Weight
Unit Dimensions
kW
BTU/h
m3/h
Liters/h
kg
dB-A
dB-A
m
mm (in.)
mm (in.)
Indoor Unit
250
799
205
270
870
295
7.5
9.0
0.06
mm
mm
mm
mm
mm
mm
kg
kg
m3
Outdoor Unit
598
660
240
650
775
344
33
35
0.17
SAP-KR97EHAXB
Control PCB
Part No.
Controls
Control Circuit Fuse
CB-KR97EHAXB
Microprocessor
250V 3.15A
RCS-7HS4E-G
Type
Q'ty ... Dia. and Length
Cross-Flow
1 ... D100 / L637
mm
Fan Motor
Type
Model ... Q'ty
No. of Poles
Rough Measure RPM (Cool / Heat)
Nominal Output
Coil Resistance
(Ambient Temp. 20 C)
Safety Device Type
Operating Temp.
Run Capacitor (on controller PCB)
Flap Motor
Type
Model
Rating
Coil Resistance
(Ambient Temp. 25 C)
AC Motor
IBH-884-066B ... 1
4
1,300 / 1,210
12.5
WHT - BRN : 234
WHT - RED : 209
Thermal fuse
130
1.5
450
W
Ohm
Open
Close
C
Micro F
VAC
Ohm
Stepping Motor
24BYJ48-916
DC 12V
Each Pair of Terminal : 200 +/- 7%
mm
m2
Indoor Unit
SAP-KR127EHAXB
Control PCB
Part No.
Controls
Control Circuit Fuse
CB-KR127EHAXB
Microprocessor
250V 3.15A
RCS-7HS4E-G
Type
Q'ty ... Dia. and Length
Cross-Flow
1 ... D100 / L637
mm
Fan Motor
Type
Model ... Q'ty
No. of Poles
Rough Measure RPM (Cool / Heat)
Nominal Output
Coil Resistance
(Ambient Temp. 20 C)
Safety Device Type
Operating Temp.
Run Capacitor (on controller PCB)
Flap Motor
Type
Model
Rating
Coil Resistance
(Ambient Temp. 25 C)
AC Motor
IBH-884-066B ... 1
4
1,300 / 1,300
12.5
WHT - BRN : 234
WHT - RED : 209
Thermal fuse
130
1.5
450
W
Ohm
Open
Close
C
Micro F
VAC
Ohm
Stepping Motor
24BYJ48-916
DC 12V
Each Pair of Terminal : 200 +/- 7%
mm
m2
SAP-CR97EHAXB
Control PCB
Compressor
Type
Compressor Model / Nominal Output
Compressor Oil ... Amount
Coil Resistance (Ambient Temp. 25 C)
Safety Device Type
Overload Relay
Operating Temp.
Run Capacitor
Open
Close
CC
Ohm
External (OLR)
B145-160-241E
160 +/- 5
69 +/- 11
Trip in 6 to 16 sec. at 16.5A
30
400
-
C
C
Micro F
VAC
Crankcase Heater
Fan
Single Rotary
C-1RV107H1D / 750W
FV68S ... 350
C - R : 4.440
C - S : 3.808
Type
Q'ty ... Dia.
Propeller
1 ... D380
mm
Fan Motor
Type
Model ... Q'ty
No. of Poles
Rough Measure RPM (Cool / Heat)
Nominal Output
Coil Resistance
(Ambient Temp. 20 C)
Safety Device Type
Operating Temp.
Run Capacitor
AC Motor
IB-976-501D ... 1
6
820 / 820
25
BLU - YEL : 213
RED (PNK) - YEL : 168
W
Ohm
Open
Close
Thermal protector
110
75
2.0
450
C
C
Micro F
VAC
mm
m2
External Finish
10
Outdoor Unit
SAP-CR127EHAXB
Control PCB
Compressor
Type
Compressor Model / Nominal Output
Compressor Oil ... Amount
Coil Resistance (Ambient Temp. 25 C)
Safety Device Type
Overload Relay
Operating Temp.
Run Capacitor
Open
Close
CC
Ohm
External (OLR)
B230-150-241E
150 +/- 5
69 +/- 11
Trip in 6 to 16 sec. at 28.0A
25
400
-
C
C
Micro F
VAC
Crankcase Heater
Fan
Single Rotary
C-RV133H1E / 950W
FV68S ... 500
C - R : 2.230
C - S : 5.187
Type
Q'ty ... Dia.
Propeller
1 ... D380
mm
Fan Motor
Type
Model ... Q'ty
No. of Poles
Rough Measure RPM (Cool / Heat)
Nominal Output
Coil Resistance
(Ambient Temp. 20 C)
Safety Device Type
Operating Temp.
Run Capacitor
AC Motor
IB-976-501D ... 1
6
840 / 840
25
BLU - YEL : 213
RED (PNK) - YEL : 168
W
Ohm
Open
Close
Thermal protector
110
75
2.5
450
C
C
Micro F
VAC
mm
m2
External Finish
11
SAP-KR97EHAXB
SAP-KR127EHAXB
PTN-41G-G2Z
Resistance
5 kohm (at 25 C)
PB2M-41E-S16-1
Resistance
15 kohm (at 0 C)
EL200/240A1-F (M)
Rating
AC277V 30A
SHF-4H-23U-P (Valve)
Rated voltage
AC220-240V 50/60Hz
12
3. DIMENSIONAL DATA
Indoor Unit
SAP-KR97EHAXB
SAP-KR127EHAXB
Unit : mm
(852-0-0010-17200-0)
13
482
78
296
264
240
45
ID
:1
8
11
372
60
87
14
47
510
660
27
127
Unit : mm
(852-0-0010-18400-0)
14
482
78
296
264
240
45
ID
:1
8
11
372
Wide tube service valve
dia.9.52(3/8")
Narrow tube service valve
dia.6.35(1/4")
60
87
14
47
598
660
27
127
Unit : mm
(852-0-0010-18500-0)
15
Indoor unit
Outdoor unit
Wide tube
Accumulator
Wide tube
service
valve
Muffler
4-way
valve
Narrow tube
Heat exchanger
Heat exchanger
O.D.
9.52 mm
(3/8 ")
Compressor
Indoor Unit
Narrow
tube
service
valve
Capillary tube
(for heating)
O.D.
6.35 mm
(1/4")
Check
valve
Cooling cycle
Capillary tube
Heating cycle
CAUTION
16
Insulation
Thickness:
Min. 8 mm
Wide tube
Thickness:
Min. 8 mm
Narrow tube
5. PERFORMANCE DATA
8
7
6
5
32
27
21
7
6
5
2
25
30
35
40
45
50
1.4
1.3
32
27
21
1.2
1.1
1.0
0.9
0.8
25
30
35
40
45
MPaG
1.6
0.7
10
15
20
25
3.8
MPaG
Low pressure at wide tube serveice valve
1.5
4.0
1.8
1.7
27
20
15
3.4
3.6
3.2
27
3.0
20
2.8
15
2.6
2.4
2.2
2.0
1.8
50
10
15
20
25
NOTE
Overload prevention operates to protect the air conditioner when outdoor ambient temperature reaches extremely high in
heating mode. (Refer to "8-6. Overload prevention.")
:Points of rating condition
Black dots in above charts indicate the following rating conditions.
Cooling: Indoor air temperature 27 C D.B. / 19 C W.B.
Heating: Indoor air temperature 20 C D.B.
Outdoor air temperature 35 C D.B. / 24 C W.B.
Outdoor air temperature 7 C D.B. / 6 C W.B.
17
Indoor Unit
SAP-KR127EHAXB
Outdoor Unit SAP-CR127EHAXB
< Cooling Characteristics >
(1) Operating current performance chart
8
7
6
32
27
21
5
4
7
6
4
3
2
25
30
35
40
45
50
1.4
1.3
32
27
21
1.2
1.1
1.0
0.9
0.8
25
30
35
40
45
MPaG
1.6
0.7
10
15
20
25
3.8
MPaG
Low pressure at wide tube serveice valve
1.5
4.0
1.8
1.7
27
20
15
3.4
3.6
27
3.2
20
15
3.0
2.8
2.6
2.4
2.2
2.0
1.8
50
10
15
20
25
NOTE
Overload prevention operates to protect the air conditioner when outdoor ambient temperature reaches extremely high in
heating mode. (Refer to "8-6. Overload prevention.")
:Points of rating condition
Black dots in above charts indicate the following rating conditions.
Cooling: Indoor air temperature 27 C D.B. / 19 C W.B.
Heating: Indoor air temperature 20 C D.B.
Outdoor air temperature 35 C D.B. / 24 C W.B.
Outdoor air temperature 7 C D.B. / 6 C W.B.
18
SAP-KR97EHAXB
Cooling
Room air temp. :
Fan speed
:
27C
High
Horizontal distance (m)
4
: Flap angle 0 ,
: Flap angle 0,
Flap angle
angle 30,
30,
:: Flap
:: Axis
Axis air
airvelocity
velocity30
30
Heating
20C
High
Horizontal distance (m)
4
:: Flap
Flap angle
angle 45
45, ,
::Axis
Axisair
airvelocity
velocity45
45
Flap angle
angle 60
60, ,
:: Flap
Axisair
airvelocity
velocity60
60
::Axis
19
Indoor Unit
SAP-KR127EHAXB
Cooling
Room air temp. :
Fan speed
:
27C
High
Horizontal distance (m)
4
: Flap angle 0 ,
:: Axis
air velocity 0
Axis air velocity 0
: Flap angle 0,
Flap angle
angle 30,
30,
:: Flap
:: Axis
Axisair
airvelocity
velocity30
30
Heating
20C
High
Horizontal distance (m)
4
Flap angle
angle 45,
45 ,
:: Flap
:: Flap
angle
60,
Flap angle 60 ,
:: Axis
Axisair
airvelocity
velocity45
45
Axisair
airvelocity
velocity60
60
:: Axis
20
Indoor Unit
SAP-KR97EHAXB
Outdoor Unit SAP-CR97EHAXB
Indoor Unit :
SAP-KR97EHAX
Outdoor Unit :
SAP-CR97EHAX
RATING CAPACITY
AIR FLOW RATE
EVAPORATOR
ENT. TEMP. oC
W.B.
D.B.
2.80 kW
3
600 m /h
TC
15
17
19
21
23
21
23
25
27
29
31
21
23
25
27
29
31
21
23
25
27
29
31
23
25
27
29
31
25
27
29
31
CM
SHC
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
CONDENSER
OUTDOOR AMBIENT TEMP.
20
25
30
35
2.82
2.70
2.58
2.45
0.60
2.06
2.35
2.65
2.82
2.82
2.82
3.03
0.62
1.75
2.05
2.34
2.64
2.93
3.03
3.22
0.64
1.44
1.73
2.03
2.32
2.62
2.91
3.41
0.66
1.41
1.71
2.01
2.30
2.60
3.62
0.67
1.38
1.67
1.97
2.26
0.65
2.00
2.29
2.59
2.70
2.70
2.70
2.90
0.67
1.69
1.99
2.28
2.58
2.88
2.90
3.08
0.69
1.38
1.67
1.97
2.27
2.56
2.86
3.26
0.71
1.36
1.65
1.95
2.24
2.54
3.47
0.73
1.32
1.62
1.91
2.21
0.70
1.94
2.24
2.53
2.58
2.58
2.58
2.76
0.72
1.64
1.93
2.23
2.52
2.76
2.76
2.94
0.74
1.32
1.62
1.91
2.21
2.50
2.80
3.12
0.76
1.30
1.60
1.89
2.19
2.48
3.30
0.78
1.26
1.56
1.86
2.15
0.75
1.88
2.18
2.45
2.45
2.45
2.45
2.63
0.77
1.58
1.87
2.17
2.47
2.63
2.63
# 2.80
0.79
1.27
1.56
1.86
2.15
2.45
2.74
2.97
0.82
1.25
1.54
1.84
2.13
2.43
3.12
0.84
1.20
1.50
1.79
2.09
TC:: Total
Total Cooling
Cooling Capacity
TC
Capacity(kW)
(kW)
SHC:: Sensible
Sensible Heat
Heat Capacity
SHC
Capacity (kW)
(kW)
CM:: Compressor
Compressor Input
Input (kW)
CM
(kW)
Ratingconditions
conditions (#Mark)
(#Mark) are
Rating
are
Outdoor Ambient
Ambient Temp.
Outdoor
Temp.35C
35 CD.B.
D.B.
Indoor Unit
Unit Entering
Entering Air
D.B.
/ 19C
W.B.
Indoor
Air Temp.
Temp.27C
27 C
D.B.
/ 19 C
W.B.
21
C
40
2.30
43
2.12
0.82
1.81
2.11
2.30
2.30
2.30
2.30
2.47
0.84
1.51
1.81
2.10
2.40
2.47
2.47
2.63
0.86
1.20
1.49
1.79
2.09
2.38
2.63
2.79
0.89
1.18
1.48
1.77
2.07
2.36
2.92
0.91
1.13
1.43
1.73
2.02
0.89
1.73
2.03
2.12
2.12
2.12
2.12
2.28
0.91
1.43
1.72
2.02
2.28
2.28
2.28
2.42
0.93
1.12
1.41
1.71
2.00
2.30
2.42
2.57
0.96
1.10
1.40
1.69
1.99
2.28
2.71
0.98
1.07
1.36
1.66
1.95
Indoor Unit
SAP-KR127EHAXB
Outdoor Unit SAP-CR127EHAXB
Indoor Unit :
SAP-KR127EHAX
Outdoor Unit :
SAP-CR127EHAX
RATING CAPACITY
AIR FLOW RATE
EVAPORATOR
ENT. TEMP. oC
W.B.
D.B.
3.30 kW
3
610 m /h
TC
15
17
19
21
23
21
23
25
27
29
31
21
23
25
27
29
31
21
23
25
27
29
31
23
25
27
29
31
25
27
29
31
CM
SHC
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
SHC
TC
CM
SHC
SHC
SHC
SHC
CONDENSER
OUTDOOR AMBIENT TEMP.
20
25
30
35
3.32
3.18
3.04
2.89
0.72
2.31
2.61
2.91
3.21
3.32
3.32
3.57
0.74
2.00
2.30
2.60
2.90
3.20
3.50
3.80
0.76
1.68
1.98
2.28
2.58
2.88
3.18
4.02
0.78
1.66
1.96
2.25
2.55
2.85
4.27
0.80
1.61
1.91
2.21
2.51
0.78
2.24
2.54
2.84
3.14
3.18
3.18
3.41
0.80
1.93
2.23
2.53
2.83
3.13
3.41
3.63
0.82
1.61
1.91
2.21
2.51
2.81
3.11
3.85
0.85
1.58
1.88
2.18
2.48
2.78
4.08
0.87
1.54
1.84
2.14
2.44
0.83
2.17
2.47
2.77
3.04
3.04
3.04
3.26
0.86
1.86
2.16
2.46
2.76
3.06
3.26
3.47
0.88
1.54
1.84
2.14
2.44
2.74
3.04
3.67
0.91
1.52
1.82
2.11
2.41
2.71
3.89
0.93
1.47
1.77
2.07
2.37
0.89
2.10
2.40
2.70
2.89
2.89
2.89
3.10
0.92
1.79
2.09
2.39
2.69
2.99
3.10
# 3.30
0.95
1.47
1.77
2.07
2.37
2.67
2.97
3.50
0.97
1.45
1.75
2.05
2.35
2.65
3.67
1.00
1.39
1.69
1.99
2.29
TC:: Total
Total Cooling
Cooling Capacity
TC
Capacity(kW)
(kW)
SHC:: Sensible
Sensible Heat
Heat Capacity
SHC
Capacity (kW)
(kW)
CM:: Compressor
Compressor Input
Input (kW)
CM
(kW)
Ratingconditions
conditions (#Mark)
(#Mark) are
Rating
are
Outdoor Ambient
Ambient Temp.
Outdoor
Temp.35C
35 CD.B.
D.B.
Indoor Unit
Unit Entering
Entering Air
D.B.
/ 19C
W.B.
Indoor
Air Temp.
Temp.27C
27 C
D.B.
/ 19 C
W.B.
22
C
40
2.72
43
2.50
0.97
2.01
2.31
2.61
2.72
2.72
2.72
2.92
1.00
1.71
2.01
2.31
2.61
2.91
2.92
3.10
1.03
1.39
1.69
1.99
2.29
2.59
2.89
3.29
1.06
1.37
1.67
1.97
2.27
2.57
3.44
1.08
1.31
1.61
1.91
2.21
1.05
1.91
2.21
2.50
2.50
2.50
2.50
2.68
1.08
1.61
1.90
2.20
2.50
2.68
2.68
2.85
1.11
1.29
1.59
1.89
2.19
2.49
2.79
3.03
1.14
1.27
1.57
1.87
2.17
2.47
3.20
1.17
1.23
1.53
1.83
2.13
120
110
100
90
80
70
60
50
40
30
20
10
0
10
15
2) Above characteristics indicate instantaneous operation, which does not take into
account defrost operation.
3) Fan speed : High
4) Because this air conditioner heats a room by drawing in the heat of the outside
air (heat pump system), the heating efficiency will fall off when the outdoor
temperature is very low. If sufficient heat cannot be obtained with this air
conditioner, use another heating appliance together with it.
23
6. ELECTRICAL DATA
Performance at
Rating Conditions
Full Load Conditions
Indoor Unit
Fan Motor
Running amp.
Power input
Running amp.
Power input
Rating conditions:
A
kW
A
kW
0.17
0.028
0.17
0.028
Outdoor Unit
Fan Motor
Compressor
230V Single-phase 50Hz
0.21
3.52
0.048
0.794
0.21
4.32
0.048
0.984
Complete Unit
Outdoor Unit
Fan Motor
Compressor
230V Single-phase 50Hz
0.21
3.12
0.048
0.699
0.21
4.32
0.048
0.984
Complete Unit
3.90
0.870
4.70
1.060
27 C D.B. / 19 C W.B.
35 C D.B.
32 C D.B. / 23 C W.B.
43 C D.B.
Heating
Performance at
Rating Conditions
Full Load Conditions
Rating conditions:
Indoor Unit
Fan Motor
Running amp.
Power input
Running amp.
Power input
A
kW
A
kW
0.17
0.028
0.17
0.028
20 C D.B.
7 C D.B. / 6 C W.B.
27 C D.B.
24 C D.B. / 18 C W.B.
24
3.50
0.775
4.70
1.060
Indoor Unit
SAP-KR127EHAXB
Outdoor Unit SAP-CR127EHAXB
Cooling
Performance at
Rating Conditions
Full Load Conditions
Indoor Unit
Fan Motor
Running amp.
Power input
Running amp.
Power input
Rating conditions:
A
kW
A
kW
0.19
0.031
0.19
0.031
Outdoor Unit
Fan Motor
Compressor
230V Single-phase 50Hz
0.21
4.20
0.048
0.946
0.21
5.30
0.048
1.171
Complete Unit
Outdoor Unit
Fan Motor
Compressor
230V Single-phase 50Hz
0.21
4.10
0.048
0.916
0.21
5.30
0.048
1.171
Complete Unit
4.60
1.025
5.70
1.250
27 C D.B. / 19 C W.B.
35 C D.B.
32 C D.B. / 23 C W.B.
43 C D.B.
Heating
Performance at
Rating Conditions
Full Load Conditions
Rating conditions:
Indoor Unit
Fan Motor
Running amp.
Power input
Running amp.
Power input
A
kW
A
kW
0.19
0.031
0.19
0.031
20 C D.B.
7 C D.B. / 6 C W.B.
27 C D.B.
24 C D.B. / 18 C W.B.
25
4.50
0.995
5.70
1.250
EVAPORATOR
BLK
WHT
RED
PNK
ORG
WARNING
GRN/YEL
TERMINAL
BASE
AC AC CM FMO 1 RV
IN-1 IN-2
GRN/YEL
RED
ORG
YEL
PNK
BLU
FLAP
1 1
2
3
4
5
2
3
4
5
FLAP
5P(WHT)
LAMP
9P(WHT)
FLAP MOTOR
1 1
2 2
3 3
4 4
5
6
7
8
9
5
6
7
8
9
RED
WHT
WHT
WHT
WHT
WHT
WHT
WHT
WHT
1 1
2 2
3 3
4 4
5
6
7
8
9
Indoor Unit
5
6
7
8 ROOM
9 THERMISTOR
CONTROLLER
FAN MOTOR
FM
(RED)
PNK
BRN
WHT
RED
BLK
YEL
1 1
3 3
5 5
1 1
2 2
3 3
FAN
5P(WHT)
HALL IC
3P(WHT)
GRN/YEL
COIL
2P (BLK)
1 1
2 2
UV
2P (RED)
1 1
2 2
COIL THERMISTOR
BLK
BLK
RED
BLK
UV UNIT
8FA2-5250-32200-0
26
4 WAY
VALVE COIL
TERMINAL
BASE (7P)
2
WHT
BLK
RED
POWER TO INDOOR
SUPPLY UNIT
20S
BLK
5
L
N
RED
OVERLOAD RELAY
(OLR)
WHT
BLU
BLK
RED
YEL
RED
GRN/YEL
FM
CAPACITOR
BLK
BLK
BLK
POWER RELAY
WHT
BLK
GND
CM
CAPACITOR
GRN/YEL
CM
FM
FAN
MOTOR
COMPRESSOR
MOTOR
8FA2-5250-32300-0
27
7. INSTALLATION INSTRUCTIONS
15 cm min.
5 cm
min.
5 cm
min.
Front View
AVOID:
Fig. 1
direct sunlight.
INDOOR
UNIT
the unit.
Elevation
difference (H)
DO:
OUTDOOR
UNIT
Fig. 2
CAUTION
Indoor unit
Wall
Minimum height
from floor level
1.5 m
Floor level
Fig. 3
Table 1
Model
Limit of Tubing
Length (L)
(m)
Limit of Elevation
Difference (H)
(m)
Required Amount of
Additional Refrigerant
(g/m)*
KR97 / 127
7.5
15
15
* If total tubing length becomes 7.5 to 15 m (max.), charge additional refrigerant (R410A) by 15 g/m.
No additional charge of compressor oil is necessary.
28
NO
AVOID:
heat sources, exhaust fans, etc. (Fig. 4)
Exhaust fan
Hot air
Heat source
Outdoor unit
DO:
position the outdoor unit in a protected location where snow will not blow into it.
choose a place as cool as possible.
Fig. 4
install in a location where at least two sides are unobstructed, so that the flow of air at the intake port or exhaust port
is not blocked, and so that sufficient space is ensured for maintenance to be carried out without trouble.
In general the top also must be unobstructed. (Fig. 5a)
provide a solid base (level concrete pad, concrete block, 10 40 cm beams or equal), a minimum of 10 cm
above ground level to reduce humidity and protect the unit against possible water damage and decreased
service life. (Fig. 5b)
Install cushion rubber under units feet to reduce vibration and noise. (Fig. 5c)
use lug bolts or equal to bolt down unit, reducing vibration and noise.
Min.
5 cm
Min. 5 cm
Air discharge
Valve
side
Min.
25 cm
Min.
20 cm
Fig. 5a
Ground
Min.
2m
Min.
2m
Obstacle
Air intake
Air discharge
Obstacle above
Min. 5 cm
Air intake
Anchor bolts
(4 pcs.)
Air intake
Min. 10 cm
Concrete
or equal
Ab
ou
t4
t
Abou
0c
Cushion rubber
(Locally
purchased)
10 c
Fig. 5c
Fig. 5b
29
Refer to the wiring system diagram (Fig. 6) for the meaning of (A) and (B) in Table 2.
Table 2
Cross-Sectional
Area (mm2)
(A) + (B)
2
3.5
CR97
33
51
CR127
27
41
Model
WARNING
Fuse or
Circuit Breaker
Capacity
10A
INDOOR UNIT
Terminal
OUTDOOR UNIT
Terminal
(B)
1
2
4
5
Grounding line
(A)
Power supply L
Single-phase N
220-240VAC 50HZ
Grounding line
Fig. 6
CAUTION
30
5
L
To remove the
remote control unit,
slide it upward.
Remote control
unit mount
Fig. 7
31
Rear side
Hole
* To prevent loss of the remote control unit, you can connect
the remote control unit to the mount by passing a string
through the remote control unit and attachment hole.
a) Press and hold the ECONOMY button and the 1HR. TIMER button.
b) Then press and hold the ACL (Reset) button with a pointed object
such as the tip of a pen. After 5 seconds, release the ACL button
first.
c) Then release the ECONOMY and 1 HR. TIMER buttons.
appears and "P1" blinking in the remote controller display
d) " " for
area. (Fig. 8b)
1HR.
TIMER
button
ON/OFF
operation
button
ECONOMY
(2) Start Automatic mode test run by pressing the ON/OFF operation button button
of the remote controller. (Fig. 8a)
ACL
(Reset)
This starts the fan producing uncooled forced air with the
button
OPERATION lamp ON on the main unit. (Fig. 8c)
After 3 minutes, the system shifts into automatic operation, and cool air will
start to be felt. Automatic mode test run is unaffected by the room temperature.
(3) Press the ON/OFF operation button of the remote controller again to stop the test
run. (Fig. 8a)
(4) Finally press the ACL (Reset) button of the remote controller to release it from
Test Run mode to return to normal mode. (Fig. 8a)
"
" for
and "P1" will disappear from the remote controller display area.
IMPORTANT
Fig. 8a
After the test run is completed, be sure to press the ACL (Reset) button to return to
normal mode. The air conditioner will not operate correctly if this is not done.
Fig. 8b
OPERATION
TIMER
LED CLEAN
ON/OFF
Fig. 8c
32
OPERATION
lamp
(1) Open the front panel until it is nearly horizontal, grasp the sections near the front panel arms on both sides,
and then remove the panel by pushing the arms towards the outside while pulling the panel towards you.
If the front panel is difficult to remove, grasp both ends of it and lift it up slightly. Move it to the left and
disengage the left arm, then move it to the right and disengage the right arm. (Fig. 9)
(2) Lift the anti-mold filter up slightly to disengage the protrusions from the hooks on the unit, and then pull
downward to remove the filter from the unit. (Fig. 9)
(3) Remove the 4 screws. Grasp the grille on both bottom sides, and pull it towards you slightly. (Fig. 10)
(4) Press the 2 tabs on the top of the grille to disengage them. (Fig. 10)
(5) Pull the grille towards you to remove it. (Fig. 10)
Arm
Front panel
Grille
Anti-mold filter
Fig. 9
Screw
Protrusions
Fig. 10
Front panel
Indentation
Arm
Fig. 11
(5) Grasp the sections near the front panel arms on both sides, and hold the
front panel so that it is nearly horizontal. Push the arm shafts towards the
outside so that they come into contact with the top of the indentations on
the right and left sides of the air conditioner. Then push firmly until the
arm shafts click into place. (Fig. 11)
(6) Insert the top of the anti-mold filter, and then fit the protrusions on the
bottom of the filter all the way into the hooks on the unit.
(7) After closing the front panel, press firmly on the parts indicated by the
arrows to securely fasten the panel in place. (Fig. 12)
NOTE
Check that no gap exists between the frame and the grille.
33
Fig. 12
Pin
NOTE
(2) Slide the rear cover of the remote control unit, and
cut the jumper wire for address switching by the
nipper then draw away the cut wires to prevent
short circuit. Slide back the rear cover. When the
wire is cut, the address is automatically set to different address (Fig. 13).
Slide the
cover
Fig. 13
1HR.
TIMER
button
ON/OFF
operation
button
ECONOMY
button
ACL
(Reset)
button
Fig. 14
34
8. FUNCTIONS
The room temperature (and other information) is transmitted every 5 minutes by the remote control unit to the
controller in the indoor unit.
Set temp.
Thermo.
OFF
T+1C
T C
Thermo.
ON
5 minutes
Thermo.
OFF
Thermo.
OFF
Room temp.
Compressor
ON
OFF
ON
OFF
ON
OFF
Outdoor fan
ON
OFF
ON
OFF
ON
OFF
Thermo. OFF : When the room temperature falls below the set temperature TC,
the compressor turns OFF.
35
(2) Heating
Room temperature control is obtained by cycling the compressor ON and OFF under control of the room
temperature sensor in the remote control unit.
The room temperature (and other information) is transmitted every 5 minutes by the remote control unit to the
controller in the indoor unit.
Thermo.
OFF
Thermo.
ON
Set temp. T C
T1 C
Room temp.
Compressor
ON
OFF
ON
OFF
Outdoor fan
ON
OFF
ON
OFF
4way valve
ON
2 minutes
OFF
ON
2 minutes
OFF
Thermo. OFF : When the room temperature rises above the set temperature TC,
the compressor turns OFF.
NOTE
The temperature described in this page and previous page gives you an example with remote
control operation. In case of the operation controled by an indoor air temperature sensor, operation
temperature differ somewhat.
36
T : Set temp.
TC
T-1C
T+2C
T+1C
T-1C
Intermittent operation
(ON for 3 minutes and OFF for 9 minutes)
FMI (indoor fan) : Indoor fan operates with rhythm airflow.
Intermittent ventilation occurs by switching the indoor fan speed between L and LL.
DRY operation does not occur when the room temperature is 15C or less, which is the monitor zone.
When the compressor stops, the indoor fan stops as well.
37
COOL
HEAT
This means that if the room temperature is higher than or equal to the set temperature, COOLING operation
begins. If the room temperature is lower than the set temperature, HEATING operation begins.
Example:
Example of operation in the AUTO mode with the set room temperature at 23 C.
Room temperature
27
26
25
24
Set temp. 23
22
21
20
19
Zone
A
B
C
C
B
Compressor
Operation mode
NOTE
Within
1 hour
More than
1 hour
A
ON
OFF
Cooling
ON
OFF
Heating
ON
Cooling
If one of the following conditions occurs, the air conditioner changes the
operation mode (from cool to heat or vice versa).
ZONE A: The mode changes if the difference between the room
temperature and the set temperature is at least 3 C.
ZONE C: The mode does not changes if the difference between the
room temperature and the set temperature is within 1 C.
38
Indoor heat
exch. coil
temp.
6C
2C
At least
approx. 2 min.
3 sec.
Outdoor fan
ON
Compressor
ON
Indoor fan
OFF
OFF
Set Speed
LL
39
ON
2 sec.
ON
Set Speed
Indoor fan speed varies according to the indoor heat exchange coil temperature as table shown below.
Condition
Compressor is in operation
(Indoor coil temp. goes up)
Compressor is stopped
(Indoor coil temp. goes down)
NOTE
*1 When the coil temperature rises above 36C, indoor fan operates in set speed.
*2 If 10 minutes has elapsed after the compressor has been stopped, the indoor fan stops its operation regardless
of the indoor heat exchange coil temperature.
36 C
Compressor : OFF
when the coil
temp. goes down
Compressor : ON
when the coil
temp. goes up
Indoor heat
30 C
exch. coil
temp.
25 C
20 C
Set Speed
Set Speed
Low
Indoor fan
Low
LL
LL
UL
UL
OFF
Compressor
OFF
OFF
ON
OFF
40
When the temperature of the indoor heat exchange coil rises above T1 C, the compressor stops, and indoor fan
runs in LL (very low speed).
Indoor heat
exch. coil
temp.
T1 C
T2 C
T3 C
Outdoor fan
OFF
H
2 sec.
Compressor
Indoor fan
ON
Set Speed
OFF
HH
MM
LM
LL
ON
Set Speed
NOTE
The operation temperature shown as T1, T2 and T3 in the chart differ by models.
97, 127 class
T1
54
T2
46
T3
40
41
Room temp.
T+2 C
T+1 C
Set temp. T C
Indoor fan
H:High
M:Medium
L:Low
T-1 C
Room temp.
Indoor fan
H:High
M:Medium
NOTE
The figure given above shows an example with remote control sensor operation. In case of the operation
controled by an indoor air temperature sensor, temperature differ somewhat.
42
Defrosting Sequence
Heating operation
Compressor ON
4-way valve ON
Frost detection
Frosting is assumed mostly under the following condition.
Indoor heat exchanger coil temperature drops 0.8C
per 6 minutes and it repeats 3 times in succession.
Indoor heat exchanger coil temperature drops below
certain extent.
Integrated operating time of compressor is longer
than 3 hours, etc.
ON
OFF
OFF
OFF
Releasing of defrosting
Defrosting time is determined by the elapsed time
which vary with certain condition. (That is: indoor
fan speed, condition of frost detection etc.)
43
Start of defrosting
60 seconds
Compressor ON
1
Release of
cold draft prevention
55 seconds
2 sec.
Compressor
ON
OFF
ON
ON
OFF
2 sec.
Outdoor fan
ON
Solenoid coil
(4way valve)
ON
ON
ON
OFF
OFF
ON
60 seconds
Indoor fan
ON
ON
NOTE
55 sec.
5 sec.
OFF
ON
OFF
44
ON
9. TROUBLESHOOTING
WARNING
Terminal
Terminal
2
1
2
4
5
Grounding line
Power supply L
Single-phase N
220-240VAC 50HZ
Grounding line
5
L
9-1-4. Check lead wires and connectors in indoor and outdoor units.
Check that coating of lead wires is not damaged.
Check that lead wires and connectors are firmly connected.
Check that wiring is correct.
45
WARNING
Turn off the circuit breaker and disconnect the power supply wiring
No
No
Power
supply
Circuit
breaker
Power
supply
wiring
Outdoor
unit
L
N
1
2
3
4
5
Ground
Fig.1
46
Inter-unit
wiring
Indoor
unit
1
2
3
4
5
(2) Circuit breaker trips in several minutes after turning the air conditioner on.
There is a possibility of short circuit.
1. Check capacity of circuit breaker.
2. Is capacity of circuit breaker
suitable ?
No
No
Circuit breaker
is tripped.
Reset breaker.
Power failure
47
Yes
No
Is operation lamp ON ?
No
Measure resistance of compressor
motor (CM) winding.
Yes
48
COOL
Is room temperature too low ?
No
No
No
49
No
Remove foreign
matter or repair.
Repair or replace.
Yes
No
P.C.Board is defective.
No
Remove foreign
matter or repair.
Repair or replace.
50
Yes
Is temperature of compressor
abnormally high ?
Measure resistance of
compressor motor winding.
Yes
Yes
No
No
Is rotor locked up ?
Yes
CAUTION
51
COOL
HEAT
HEAT
COOL
52
No
No
Yes
If temperature difference
is small, possibility of
gas shortage.
Evacuate the
air conditioner.
Charge refrigerant
in liquid. (R410A)
Yes
Recover
refrigerant.
Yes
No
No
53
R410A is a new refrigerant that contains two types of pseudo-non-azeotropic refrigerant mixture. Its
refrigeration capacity and energy efficiency are about the same level as the conventional refrigerant, R22.
10-1-3. Characteristics
Less toxic, more chemically stable refrigerant
The composition of refrigerant R410A changes whether it is in a gaseous phase or liquid phase. Thus, when
there is a refrigerant leak the basic performance of the air conditioner may be degraded because of a change in
composition of the remaining refrigerant. Therefore, do not add new refrigerant. Instead, recover the
remaining refrigerant with the refrigerant recovery unit. Then, after evacuation, totally recharge the specified
amount of refrigerant with the new refrigerant at its normal mixed composition state (in liquid phase).
When refrigerant R410A is used, the composition will differ depending on whether it is in gaseous or liquid
phase, and the basic performance of the air conditioner will be degraded if it is charged while the refrigerant is in
gaseous state. Thus, always charge the refrigerant while it is in liquid phase.
CAUTION
Ether-type oil is used for compressor oil for R410A-type units, which is different
from the mineral oil used for R22. Thus more attention to moisture prevention and
faster replacement work compared with conventional models are required.
Use a clutch-type flare tool for R410A or the conventional flare tool. Note that sizes of the resultant flares differ
between these two tools. Where a conventional flare tool is used, make sure to observe A Specification (amount of
extrusion) by using the flare spacer.
Diameter of tube D
Dia.6.35 mm (1/4")
Dia.9.52 mm (3/8")
Specification A
0 to 0.5 mm
Dia.12.7 mm (1/2")
1.2 mm
Dia.15.88 mm (5/8")
Size of flare
D
D
A
Spacer
54
Tubing precautions
Refrigerant R410A is more easily affected by dust or moisture compared with R22, thus be sure to temporarily
cover the ends of the tubing with caps or tape prior to installation.
Never use 0.7mm-thick copper tubing or tubing which is less than 0.8mm in thickness, since air conditioners with
R410A are subject to higher pressure than those using R22 and R407C.
No addition of compressor oil for R410A
No additional charge of compressor oil is permitted.
No use of refrigerant other than R410A
Never use a refrigerant other than R410A.
If refrigerant R410A is exposed to fire
Through welding, etc., toxic gas may be released when R410A refrigerant is exposed to fire. Therefore, be sure
to provide ample ventilation during installation work.
Caution in case of R410A leak
Check for possible leak points with the special leak detector for R410A. If a leak occurs inside the room,
immediately provide thorough ventilation.
55
Tool Name
Gauge manifold
Charging hose
Gas leak detector
Refrigerant cylinder
Charging cylinder
Refrigerant recovery unit
CAUTION
Bender
Torque wrench
Cutter, reamer
Welding tool, nitrogen gas cylinder
The above tools specifically for R410A must not be used for R22 and R407C.
Doing so will cause malfunction of the unit.
For the above vacuum pump (*1, *2) and vacuum pump adapter (*3), those for
R22-type units can be used for R410A-type. However, they must be used
exclusively for R410A and never alternately with R22 and R407C.
To prevent other refrigerants (R22, R407C) from being mistakenly charged to this unit, shape and external
diameter of the service port screw has been altered.
<External diameter of service port> R410A : 7.94 mm (5/16")
R22, R407C : 6.35 mm (1/4")
For details on tubing installation procedures, refer to the installation manuals attached to the indoor
unit and outdoor unit.
56
(4) Evacuation
Use a solenoid valve-installed vacuum pump so that
even if power is cut off in the middle of evacuation of air
due to a power interruption, the valve will prevent the
pump oil from flowing back.
(4) Evacuation
OK
57
(5) Recharge
(5) Recharging
Valve
Liquid
Single valve
Charge liquid refrigerant with
cylinder in up-side-down position.
Fig. 1
Valve
Liquid
Example:
In case of charging refrigerant to a unit requiring
0.76Kg using a capacity of a 10Kg cylinder, the
minimum necessary amount for the cylinder is:
0.76 + 10
0.20 = 2.76Kg
Fig. 2
NO!
Charging
cylinder
Liquid
Open
58
Refrigerant
cylinder
Fig. 3
Never attempt to charge additional refrigerant when refrigerant has been leaking
from the unit. Follow the procedure described below to locate points of leaks and
carry out repairs, then recharge the refrigerant.
Use nitrogen gas for the pressurized gas, and never use
a refrigerant other than R410A. Also do not use oxygen or
any flammable gas.
(5) Evacuation
Use a solenoid valve-installed vacuum pump so that
even if power is cut off in the middle of evacuation of air
due to a power interruption, the valve will prevent the
pump oil from flowing back.
The equipment may be damaged if moisture remains in
the tubing, thus carry out the evacuation thoroughly.
When using a vacuum pump with exhaust air volume
more than 25L/min. and ultimate vacuum pressure rate of
0.05Torr.
Standard time for evacuation
Length of tubing
Evacuation time
(6) Recharging
Recharge unit in the same manner explained on the
previous page "(5) Recharging."
59
OK
(5) Evacuation
OK
(6) Recharge
Never charge additional refrigerant if refrigerant is leaking from the unit. Follow
instructions given in "10-6. In Case Refrigerant is Leaking" and completely carry
out repairs. Only then should you recharge the refrigerant.
60
Ground wire
Clip
Probe
Insulation
tester
Fig. 1
Terminal plate
Probe
Clip
Copper
tube or
metallic part
Insulation
tester
Fig. 2
Probe
Clip
Copper
tube or
metallic part
Insulation
tester
NOTE
Fig. 3
From fan motor,
compressor and
other parts
Metallic
part
Probe
Clip
Fig. 4
61
Insulation
tester
Fuse
PCB Ass'y
Fig. 5
Fuse
Fig. 6
Multimeter
Compressor motor
capacitor
Fan motor
capacitor
Fig. 7
62
SAP-KR97EHAXB + SAP-CR97EHAXB
SAP-KR127EHAXB + SAP-CR127EHAXB
(OI-852-6-4181-087-00-0)
63
SAP-KR97EHAXB
SAP-KR127EHAXB
COOL/DRY/HEAT Model
INSTRUCTION MANUAL
Split System Air Conditioner
MANUAL DE INSTRUCCIONES
Acondicionador de aire de dos unidades
MODE DEMPLOI
Climatiseur de type spar
BEDIENUNGSANLEITUNG
Splitsystem-Klimagert
MANUAL DE INSTRUES
Aparelho de ar condicionado do sistema split
O O
Pub.
OI-85264181087000
SANYO 2008
FEATURES
This air conditioner is equipped with cooling, heating, and drying functions. Details on these functions are provided below; refer to these
descriptions when using the air conditioner.
Microprocessor Controlled Operation
Auto/High/Medium/Low
Air Sweep Control
CONTENTS
Page
FEATURES ......................................................................................................................................... 2
PRODUCT INFORMATION ................................................................................................................ 3
ALERT SYMBOLS .............................................................................................................................. 3
INSTALLATION LOCATION ................................................................................................................ 3
ELECTRICAL REQUIREMENTS........................................................................................................ 3
SAFETY INSTRUCTIONS .................................................................................................................. 3
NAMES OF PARTS............................................................................................................................. 4
USING THE REMOTE CONTROL UNIT ............................................................................................ 8
OPERATION WITH THE REMOTE CONTROL UNIT ........................................................................ 9
1. Automatic Operation............................................................................................................ 9
2. Manual Operation ................................................................................................................ 9
3. Adjusting the Fan Speed ................................................................................................... 10
4. Fan Only ............................................................................................................................ 10
5. ECONOMY Mode .............................................................................................................. 10
6. QUIET Mode ..................................................................................................................... 10
7. LED CLEAN Mode ............................................................................................................ 11
SPECIAL REMARKS........................................................................................................................ 11
USING THE 12-HOUR ON AND OFF TIMER .................................................................................. 11
USING THE 1-HOUR OFF TIMER ................................................................................................... 12
TIPS FOR ENERGY SAVING........................................................................................................... 13
ADJUSTING THE AIRFLOW DIRECTION ....................................................................................... 13
OPERATION WITHOUT THE REMOTE CONTROL UNIT ............................................................... 14
CARE AND CLEANING.................................................................................................................... 14
TROUBLESHOOTING...................................................................................................................... 15
OPERATING RANGE ....................................................................................................................... 15
OI-087-2-EG
PRODUCT INFORMATION
If you have problems or questions concerning your Air
Conditioner, you will need the following information.
Model and serial numbers are on the nameplate on the
bottom of the cabinet.
Model No. __________________________________
Serial No. ___________________________________
ELECTRICAL
REQUIREMENTS
1. All wiring must conform to the local electrical codes.
Consult your dealer or a qualified electrician for
details.
2. Each unit must be properly grounded with a ground
(or earth) wire or through the supply wiring.
3. Wiring must be done by a qualified electrician.
SAFETY INSTRUCTIONS
Read this Instruction Manual carefully before
using this air conditioner. If you still have any
difficulties or problems, consult your dealer for
help.
This air conditioner is designed to give you
comfortable room conditions. Use this only for its
intended purpose as described in this Instruction
Manual.
Never use or store gasoline or other
flammable vapor or liquid near the
air conditioner it is very
dangerous.
This air conditioner has no ventilator
for intaking fresh air from outdoors.
You must open doors or windows
frequently when you use gas or oil
heating appliances in the same
room, which consume a lot of
oxygen from the air. Otherwise there
is a risk of suffocation in an extreme
case.
ALERT SYMBOLS
The following symbols used in this manual, alert
you to potentially dangerous conditions to users,
service personnel or the appliance:
This symbol refers to a hazard or
unsafe practice which can result in
severe personal injury or death.
CAUTION
INSTALLATION LOCATION
We recommend that this air conditioner be
installed properly by qualified installation
technicians in accordance with the Installation
Instructions provided with the unit.
Before installation, check that the voltage of the electric supply in your home or office is the same as the
voltage shown on the nameplate.
CAUTION
Avoid:
To protect the air conditioner from heavy corrosion, avoid installing
the outdoor unit where salty sea water can splash directly onto it
or in sulphurous air near a spa.
OI-087-3-EG
NAMES OF PARTS
Air intakes
INDOOR UNIT
OPERATION lamp
OPERATION
Air outlet
TIMER lamp
TIMER
LED CLEAN
ON/OFF
OPERATION button
(ON/OFF)
Drain hose
Refrigerant tubes
OUTDOOR UNIT
IMPORTANT
Avoid using radio equipment such as mobile phone near
(within 1 m) the remote control receiver. Some radio
equipment may cause malfunction of the unit.
If the trouble happens, disconnect power and restart the air
conditioner after a few minutes.
REMOTE
CONTROL
receiver
OPERATION
button
Air outlet
NOTE
COOLING
HEATING
OPERATION OPERATION
STOP
lamp
on
on
off
beeping
sound
twice
once
once
Air Intake
Air Outlet
Remote
Control Unit
Refrigerant
Tubes
TIMER lamp
Drain Hose
LED CLEAN
lamp
NOTE
The TIMER lamp may not light again after recovery from a power
failure.
OI-087-4-EG
Displayed when
transmitting data
Displayed when
indoor unit
sensor is in use
Displayed when
setting timer
Symbols
(1) Operation mode
(4) Timer
AUTO .....................................
HEAT ......................................
COOL .....................................
FAN ........................................
(6) Confirmation
of transmission.......................
OI-087-5-EG
Display
Information on the operating conditions is displayed while the remote
control unit is switched on. If the unit is turned off, FLAP setting and
FAN SPEED setting are not displayed.
(AUTO)
(HEAT)
(DRY)
(COOL)
(FAN)
ECONOMY button
For details, see 5. ECONOMY Mode. When you press this button in the
HEAT, DRY or COOL mode, the
mark appears in the display, and the
remote control unit will automatically adjust the set temperature to save
energy.
SENSOR button
When you press this button (use a small-tipped object such as a ballpoint
pen), the
mark will appear at the display. And the room temperature is
detected by the sensor which is built into the indoor unit and the air
conditioner is controlled accordingly.
NOTE
If the remote control is located near a heat source, such as a space heater or
in direct sunlight, press the SENSOR button to switch to the sensor on the
indoor unit.
OI-087-6-EG
Sensor
A temperature sensor inside the remote control unit senses the room
temperature.
FLAP button
Press this button either to select the setting of the airflow direction to the
auto. flap in each mode or one of the six possible positions manually or to
select the sweep function which moves the flap up and down
automatically.
: Auto flap setting: If selected in a heating operation, the flap is set
to position (3) in the following chart. If selected in a cooling or dry
operation, the flap is set at position (7) in the following chart.
: The airflow direction can be set manually. (six positions)
: The flap moves up and down automatically.
NOTE
When you press the FLAP button, the air flow direction will be changed
one by one as follows.
SWEEP
CANCEL button
After using the TIMER ON button or TIMER OFF button to set the timer,
press this button to cancel the setting.
QUIET button
: When you press this button, the fan rotates slower than the
fan speed setting to provide a quieter operating sound.
NOTE
The remote control unit sends the temperature signal to the air conditioner regularly at five minute
intervals. If the signal from the remote control unit stops for more than 15 minutes due to the loss of the
remote control unit or other trouble, the air conditioner will switch to the temperature sensor which is
built into the indoor unit and control the room temperature. In these cases, the temperature around the
remote control unit may differ from the temperature detected at the air conditioners position.
OI-087-7-EG
ACL button
NOTE
The batteries last about six months, depending on how
much you use the remote control unit. Replace the batteries
when the remote control units display fails to light, or
when the remote control cannot be used to change the air
conditioners settings.
Use two fresh leak-proof type-AAA alkaline batteries.
In replacing batteries, follow the instructions as mentioned
in the sub-section HOW TO INSTALL BATTERIES.
If you do not use the remote control unit more than 1
month, take out the batteries.
NOTE
Remote control
unit mount
Rear side
Air conditioner
(Indoor unit)
Hole
To prevent loss of the remote control unit, you can connect the
remote control unit to the mount by passing a string through the
remote control unit and attachment hole.
Receiver
Remote control
unit
(Transmitter head)
OI-087-8-EG
2. Manual Operation
STEP 2
STEP 1
STEP 3
STEP 5
STEP 2
STEP 4
STEP 1
NOTE
NOTE
STEP 2
STEP 1
STEP 2
STEP 3
NOTE
STEP 4
STEP 5
NOTE
OI-087-9-EG
and
4. Fan Only
Setting
temperature
STEP 2
STEP 1
1 C
1 C
Press the
ECONOMY button
B. In Heating Mode: (
STEP 3
If you want to circulate air without any temperature
control, follow these steps:
STEP 1
STEP 2
STEP 3
30 min.
30 min.
Time
Setting
temperature
2 C
2 C
5. ECONOMY Mode
Press the
ECONOMY button
30 min.
30 min.
Time
6. QUIET Mode
QUIET Mode is used to reduce the fan sound of the indoor unit.
Press the QUIET button.
The
mark appears in the display.
To cancel, press QUIET button again.
In QUIET Mode, the fan rotates at a slower speed than the fan
speed setting.
If the unit is already operating with a very low (LL) airflow, the fan
sound may not change even if the QUIET button is pressed.
10
OI-087-10-EG
Clicking Sound
Clicking sound is heard from the air conditioner
NOTE
Pressing the MODE selector button cancels LED CLEAN mode.
Do not open the front panel while the LED CLEAN lamp on the
display is on.
Depending on the room brightness, light from the LED CLEAN
lamp may reflect inside the air conditioner and be visible. This is
not a malfunction.
SPECIAL REMARKS
DRY (
STEP 1
) Operation
How it works?
Once the room temperature reaches the level that was set, the
unit repeats the cycle of turning on and off automatically.
During DRY operation, the fan speed is automatically set to Low
speed for providing a comfortable breeze.
DRY operation is not possible if the indoor temperature is 15 C
or less.
Heating (
) Operation
STEP 2
STEP 3
After the length of time set for TIMER ON elapses, the unit
begins operating.
The display depicted above indicates that the air conditioner will
begin operating in three hours.
Setting procedure:
Heating performance
STEP 1
STEP 2
Defrosting
STEP 3
3.......12
NOTE
If you do not operate the remote control unit for 25 hours or more
after the start of ON timer operation, the unit will stop operating
automatically as a safety measure in case you forget to turn off the
air conditioner.
OI-087-11-EG
11
Setting procedure:
STEP 2
STEP 1
STEP 2
After the length of time set for TIMER OFF elapses, the unit
stops operating.
The display depicted above indicates that the air conditioner will
stop operating in five hours.
Setting procedure:
Press the TIMER OFF button.
STEP 2
TIMER OFF
display during
counting after
3 hours has
elapsed
3.......12
TIMER ON
display during
counting
STEP 1
12
STEP 1
Timer setting
Stop
Operate
3 hours
2 hours
5 hours
This function causes the unit to operate for one hour and
then stop, regardless of whether the unit is on or off when
this button is pressed.
The
indicator in the display indicates that this function is
operating.
Setting procedure:
Regardless of whether the unit is operating or stopped, press the
1 HR. TIMER button.
appears in the display.
Cancellation procedure:
Press the ON/OFF operation button to turn the unit off, wait for the
unit to stop operating, and then press the ON/OFF operation
button again.
The 1-Hour Timer function is now cancelled and the unit operates
normally.
NOTE
If, while the 1-Hour Timer function is operating, the 1HR. TIMER
button is pressed once to cancel the function and then again, the
unit continues to operate for one hour from that point in time and
then stops.
It is not possible to use the OFF Timer and 1-Hour OFF Timer
together. Whichever function is set last takes precedence. If the
1 HR. TIMER button is pressed while the TIMER OFF function
operates, the OFF Timer is cancelled and the unit will stop
operating one hour later.
Do not use the 1-Hour OFF Timer when both TIMER ON and
TIMER OFF are set simultaneously. If the 1-Hour OFF Timer
has been set, press the TIMER OFF button, then the
CANCEL button to operate both the 1-Hour OFF Timer and
ON Timer simultaneously.
OI-087-12-EG
Timer setting
Operate
1 hour
Stop
Operate
CAUTION
When the humidity is high, the vertical vanes should be in the
front position during the cooling or dehumidifying operation.
If the vertical vanes are positioned all of the way to the right
or left, condensation may begin to form around the air vent
and drip down.
2. Vertical
The vertical airflow can be adjusted by moving the flap with the
remote control unit. Do not move the flap with your hands. Confirm
that the remote control unit has been turned on. Use the FLAP
button to set either the sweep function or one of the six airflow
direction settings.
2 hours
3 hours
Setting procedure:
STEP 1
STEP 2
NOTE
Set the 1-Hour OFF Timer and the 12-Hour ON Timer
simultaneously.
Unless you set the 1-Hour OFF Timer and the 12-Hour ON
Timer at the same time, the 1-Hour OFF Timer may operate for
one hour or more.
Do
Always try to keep the air filter clean. (Refer to CARE AND
CLEANING.) A clogged filter will impair the performance of the
unit.
To prevent conditioned air from escaping, keep windows, doors
and any other openings closed.
A. Sweep function
The flap starts moving
up and down to deliver
SWEEP
air over the sweep
COOL
range.
DRY
SWEEP
HEAT
FAN
NOTE
Knob
OI-087-13-EG
CAUTION
Use the FLAP button on the remote control to adjust the
position of the flap. If you move the flap by hand, the flap
position according to the remote control and the actual flap
position may no longer match. If this should happen, shut
off the unit, wait for the flap to close, and then turn on the
unit again; the flap position will now be normal again.
Do not have the flap pointed down during cooling
operation. Condensation may begin to form around the air
vent and drip down.
13
CAUTION
INDOOR UNIT
OPERATION lamp
OPERATION
TIMER
LED CLEAN
Anti-Mold Filter
ON/OFF
The anti-mold filter behind the front panel should be checked and
cleaned at least once every two weeks.
OPERATION button
(ON/OFF)
If you have lost the remote control unit or it has trouble, follow the
steps below.
Front panel
STOP
lamp
on
on
off
beeping
sound
twice
once
once
Anti-mold filter
The type of operation is indicated by the OPERATION lamp
lighting and the beeping sound.
Protrusions
NOTE
The temperature is set to the room temperature minus 2C during
the cooling operation and to the room temperature plus 2C during
the heating operation, and the fan speed and flap are set to Auto.
Cleaning
Use a vacuum cleaner to remove light dust. If there is sticky dust
on the filter, wash the filter in lukewarm, soapy water, rinse it in
clean water, and dry it.
2. Press the locations marked by the arrows and close the front
panel.
14
OI-087-14-EG
Trouble
Air conditioner does
not run at all.
NOTE
Do not bend nor give excessive force onto the air clean filter.
If the filter surface is heavily blocked with dirt or damaged,
replace it with new one. Purchase a replacement filter at your
local dealer. (model STK-FWWB)
2. Eliminate heat
source if possible.
4. Remove it to
ensure good
airflow.
5. Thermostat is set
5. Set the
too high for cooling
temperature lower
(or too low for
(or higher).
heating).
6. (Outdoor
temperature is too
low for heating.)
6. (Consult your
dealer or try to use
another heat
appliance.)
OPERATION lamp
The use of cellular
lights but outdoor unit phones near the air
will not run.
conditioner may
cause disturbance to
its normal operation.
OPERATING RANGE
The air conditioner is operable within the temperature ranges as
listed below:
Temperature
Indoor air
temperature
Outdoor air
temperature
COOLING Max.
32 C DB /
23 C WB
43 C DB
Min.
19 C DB /
14 C WB
19 C DB
Max.
27 C DB
24 C DB /
18 C WB
Min.
16 C DB
8 C DB /
9 C WB
TROUBLESHOOTING
OI-087-15-EG
2. Heat source or
many people in
room.
Contact service
center.
3. Doors and/or
3. Shut them to keep
windows are open.
the heat (or cold)
out.
Clicking sound is
heard from the air
conditioner.
If your air conditioner does not work properly, first check the
following points before requesting service. If it still does not work
properly, contact your dealer or service center.
3. Consult your
electrician or
dealer.
Arm
Clean the front panel gently using a soft sponge, or the like.
Then wipe away any remaining moisture.
Neutral detergent may be used to remove stubborn dirt. Then
rinse thoroughly with water and wipe away any remaining
moisture.
Removing
Open the front panel until it is nearly horizontal, grasp the
sections near the front panel arms on both sides, and then
remove the panel by pushing the arms towards the outside while
pulling the panel towards you.
If the front panel is difficult to remove, grasp both ends of it and
lift it up slightly.
Move it to the left and disengage the left arm, then move it to the
right and disengage the right arm.
2. Contact service
center.
CAUTION
1. Restore power.
2. Leakage circuit
breaker tripped.
Trouble in system.
Remounting
Grasp the sections near the front panel arms on both sides, and
hold the front panel so that it is nearly horizontal. Push the arm
shafts towards the outside so that they come into contact with
the top of the indentations on the right and left sides of the air
conditioner. Then push firmly until the arm shafts click into place.
After closing the front panel, press firmly on the parts indicated
by the arrows to securely fasten the panel in place.
Also refer to the figure that shows How to replace the anti-mold
filter.
1. Power failure.
OPERATION lamp
blinks and air
conditioner does not
operate.
Front panel
Remedy
Possible Cause
HEATING
15