Appendix

Control Theory Quiz

A set of questions with multiple answer choices is given here. These questions have been designed to capture important
aspects of Control Theory covered in the book. For each of these questions, identify the best of the given answer
choices. Compare your answers with the master key given at the end of the session. This quiz should serve the purpose
of a self-appraisal test for the reader.
1. A linear time-invariant system initially at rest, when subjected to a unit-step input, gives a response y(t) = tet;
t > 0. The transfer function of the system is
(A)

(B)

( s + 1)2

1
s ( s + 1)

2. The system shown in Fig. Q2 is of

(A) zero order
(B) first order
(C) second order
(D) third order
3. The impulse response of an initially relaxed linear
system is e2tm(t) where m(t) is a unit step function.
To produce a response of te2t m(t), the input must
be equal to

(C)

(D)

( s + 1)2

1
s ( s + 1)

Displacement x
(output)

K
M

Force F
(input)

1 2t
B
e m(t)
2
(c) e2t m(t)
(D) e t m(t)
Fig. Q2
4. The step response of a system with transfer function
G(s) = 1/(t s + 1) attains more than 98% of its final
value in time t equal to
(A) t
(B) 2t
(C) 3t
(D) 4t
5. The response of the system of Fig. Q5a to an input r(t) = 8m(t) is shown in Fig. Q5b. The time-constant t is equal to
(A) 0.535 msec
(B) 0.32 msec
(C) 0.09 msec
(D) 11.25 msec
(A) 2e2t m(t)

Appendix-B OLC.p65

(B)

15

4/22/08, 3:44 PM

16

Control Systems: Principles and Design

r(t)

y(t)

1
ts + 1

3.6

0.32

t (msec)

(a)

(b)
Fig. Q5

6. Closed-loop transfer function of a unity-feedback system is given byY(s)/R(s) = 1/(ts + 1). Steady-state error to
unit-ramp input is
(A)
(B) t
(C) 1
(D) 1/t
7. The series RLC circuit shown in Fig. Q7 is underdamped if
2

1
R
(A) <
2L
LC

i(t)

1
R
(B) =
2L
LC

e0(t)

1
R
(C) >
2L
LC
(D) None of the answers in (A), (B), and (C) is correct
8. Closed-loop transfer function of a unity-feedback

Fig. Q7

R1
Y (s )
w n2
.
= 2
2
R ( s ) s + 2 z wn s + wn
Steady-state error to unit-ramp input is
e
e3
e1
C1 2
(A)
(B) 2z/wn
(C) 1
(D) 4/zwn
9. When two networks shown in Fig. Q9 are
E2(s) = H (s)
1
cascaded in tandem, the overall transfer function
E1(s)
E4(s)/E1(s) is
Fig. Q9
(B) H1(s) + H 2(s)
(A) H1(s) H2 (s)
(D) None of the answers in (A), (B), and (C) is correct
(C) H1(s)/H2(s)
10. Dead-time model estD may be approximated by the transfer function

system is given by

tD
s
2
(A)
t
1+ D s
2

tD
s
2
(B)
t
1- D s
2

1-

1+

(C)

1 - tD s
1 + tD s

(D)

R2

C2

e4

E4(s) = H (s)
2
E3(s)

1 + tD s
1 - tD s

11. If a system has two real and equal characteristic roots, it is described as
(A) having no damping
(B) being underdamped
(C) being critically damped (D) being overdamped
12. If the roots of a characteristic equation are given by s1,2 = 3 j2, the values of damping z and damped natural
frequency w d are

Appendix-B OLC.p65

16

4/22/08, 3:44 PM

17

Appendix B: Control Theory Quiz

3

, 13
(A)
13

,2
(B)
13

, 13
(C)
13

,2
(D)
13

13. A liquid-level system comprises two noninteracting tanks which can be represented by two first-order transfer
functions in cascade having time constants t1 = 100 sec and t2 = 300 sec. The inflow q(t) is the input and the
level of the second tank is the output. The response of the output height to a step change in flow will be
(A) having no damping
(B) underdamped
(C) critically damped
(D) overdamped
14. An open-loop control system requires an operator
Constant flow
to set a motorized valve setting c where 0 < c < 1,
10 m3/hr
so that two fluids are mixed together. One stream
3
has a constant flow of 10 m /hr and the outflowing
stream should be 14 m3/hr. The configuration is
1
c
20
shown in Fig. Q14, where motorized valve
0.5
0.4s + 1
Desired flow
dynamics are given. The value of valve setting to
0
14 m3/hr
achieve the desired steady-state outflow is
Fig. Q14
(A) 0.2
(B) 0.4
(C) 0.5
(D) 0.7
15. A linear approximation at the operating point (x* = 0.5, u* = 1.5) to y(x, u) = 2x2 + xu + u2, is
(A) dy = 3.5 dx + 3.5 du (B) dy = 4 dx + 2 du
(C) dy = 2 dx + 3 du
(D) dy = 4.75 dx + 3.75 du
16. In a level control system, the fluid flow is related to the inflow rate by the following transfer function:
G(s) =

level H ( s )
0.75
=
inflow Q( s ) 2500 s + 1

Initially the tank is empty. The inflow control valve is suddenly opened to allow a flow rate of 0.5 m 3/sec into the
tank. The level after 2500 sec is
(A) 0.474 m
(B) 0.375 m
(C) 0.75 m
(D) 0.237 m
17. The system of Fig. Q17 is underdamped of

K B
>
M 2 M

K B
=
(B)
M 2M

(A)

Force F
(input)

M
2

K B
<
M 2M
(D) None of the answers in (A), (B) and (C) is correct
18. The damping ratio of the system of Fig. Q18 is
1 1
(A)
2 BM

(C)

(B)

Displacement x
(output)

Fig. Q17

Displacement x
(output)

1 M
2 B

1 B
2 M
(D) None of the answers in (A), (B), and(C) is correct.

Force F
(input)

(C)

B
Fig. Q18

Appendix-B OLC.p65

17

4/22/08, 3:44 PM

18

Control Systems: Principles and Design

Amplitude

19. For a second-order system with damping z > 1, the

2
roots of the characteristic equation are
1.8
(A) real but not equal
(B) real and equal
1.6
(C) complex conjugate
(D) imaginary
1.4
20. The plot in Fig. Q20 shows the unit step response of
a first-order system. Transfer function of the system
1.2
is
1
1
2
(B)
(A)
0.8
5s + 1
15s + 1
0.6
2
1
(C)
(D)
0.4
3s + 1
15s + 1
21. Three different systems have the following poles: p1
0.2
= 0.2, p2 = 0.4, p3 = 0.6. What is the time0
constant of the fastest step response?
0
5
10
15
20
(A) 0.2
(B) 0.6
Time (seconds)
(C) 1/0.2
(D) 1/0.6
Fig. Q20
22. Consider the following statements:
(i) The test signals step, ramp and parabola are not useful for control-system analysis if actual inputs are not
step, ramp, and parabola, respectively.
(ii) Transient and steady-state performance of control systems is adequately given by the response to only one
test signal, say step.
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
23. Consider the op amp circuit shown in Fig. Q23. It can be used as
(A) a lead compensator only
(B) a lag compensator only
(C) either a lead or a lag compensator
(D) neither a lead nor a lag compensator
C2
C1

R4
R2

R1

e1

R3

e2

Fig. Q23
24. Consider the block diagram shown in Fig. Q24. The transfer function between Y(s) and W(s) is

Appendix-B OLC.p65

(A)

D (s) G (s) N (s )
1 + D (s) G (s) H (s )

(B)

(C)

N (s )
1 - D( s) G ( s) H ( s)

(D) None of the answers in (A), (B), and (C) is correct

18

N (s )
1 + D (s) G (s) H (s )

4/22/08, 3:44 PM

19

Appendix B: Control Theory Quiz

W(s)

R(s)

N(s)

G (s )

D(s)

Y(s)

H (s )

Fig. Q24
25. The gear train shown in Fig. Q25
(A) reduces the speed and the torque
Drive
shaft
(B) increases the speed and the torque
(C) reduces the speed and increases the torque
(D) increases the speed and reduces the torque
Load
26. Effect of back emf in an armature-controlled dc servomotor is
shaft
(A) to increase effective motor friction, thereby reducing motor
time-constant
(B) to increase effective motor friction, thereby increasing motor
Fig. Q25
time-constant
(C) to increase motor inertia, thereby increasing motor timeconstant
(D) to increase motor inertia, thereby reducing motor time-constant
27. Electrical time-constant of an armature-controlled dc servomotor is
(A) equal to mechanical time-constant
(B) smaller than mechanical time-constant
(C) larger than mechanical time-constant
(D) None of the answers in (A), (B), and (C) is correct
28. Ratio of the rotor reactance X to the rotor resistance R for a two-phase servomotor
(A) is equal to that of a normal induction motor
(B) is less than that of a normal induction motor
(C) is greater than that of a normal induction motor
(D) may be less or greater than that of a normal induction motor
29. A rotating load is connected to a field-controlled dc motor with negligible field inductance. A test results in
output steady-state speed (w) of 2 rad/sec when an input voltage (ef ) of 100 V is applied to the motor terminals.
Also the test shows that output speed reaches 0.632 2 rad/sec within 0.75 sec. The transfer function w (s)/Ef (s)
of the motor is
(A)

0.02
(0.375s + 1)

(B)

0.02
0.75s + 1

(C)

50
0.75s + 1

30. The transfer function from R(s) to Y(s) of the system of Fig. Q30 is
(A)
(C)

Appendix-B OLC.p65

s (t s + 1)
t s 2 + (1 + KK 2 ) s + KK1
2

KK1

t s + (1 + KK 2 ) s + KK1

19

(B)
(D)

K1s (t s + 1)

t s 2 + (1 + KK 2 ) s + KK1
2

s (t s + 1 + KK 2 )

t s + (1 + KK 2 ) s + KK1

4/22/08, 3:45 PM

(D)

50

(0.375s + 1)

20

Control Systems: Principles and Design

W(s)
R(s)

E(s)

U(s)

K1

K
ts + 1

1
s

Y(s)

K2s

Fig. Q30
31. The transfer function from W (s) to Y(s) of the system of Fig. Q30 is
(A) 1
(C)

(B)

KK1
t s + (1 + KK 2 ) s + KK1
2

s (t s + 1)
t s 2 + (1 + KK 2 ) s + KK1

(D) None of the answers in (A), (B), and (C) is correct

32. The transfer function between R(s) and E(s) of the system of Fig. Q30 is
(A)
(C)

s (t s + 1 + KK 2 )
t s 2 + (1 + KK 2 ) s + KK1
KK1

t s 2 + (1 + KK 2 ) s + KK1

(B)
(D)

s (t s + 1)
t s 2 + (1 + KK 2 ) s + KK1
K1s (t s + 1)

t s 2 + (1 + KK 2 ) s + KK1

33. The transfer function between R(s) and U(s) of the system of Fig. Q30 is
(A)
(C)

s (t s + 1)
t s 2 + (1 + KK 2 ) s + KK1
KK1

t s 2 + (1 + KK 2 ) s + KK1

(B)
(D)

s (t s + 1 + KK 2 )

t s 2 + (1 + KK 2 ) s + KK1
K1s (t s + 1)

t s 2 + (1 + KK 2 ) s + KK1

34. Consider the following statements:

(i) Synchro is a three phase machine.
(ii) Rotor of synchro transmiter is of dumb bell type while that of control transformer is cylindrical.
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
35. Consider the following statements:
(i) AC devices (servomotor, synchro) are normally operated at higher frequencies (400 Hz, for example) and
not at 50 Hz.
(ii) The output of a synchro is demodulated before feeding it to a dc motor for actuation of inertial load.
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true

Appendix-B OLC.p65

20

4/22/08, 3:45 PM

21

Appendix B: Control Theory Quiz

36. A position control system has a two-loop configuration. The minor loop is a velocity-feedback loop realized
through tachogenerator. Consider the following statements:
(i) The tacho is usually mounted on motor shaft rather than the load shaft.
(ii) The minor loop is a positive-feedback loop.
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statment (i) is false but statement (ii) is true
(D) Both the statements are true
37. Feedback control systems are
(A) insensitive to both forward- and feedback-path parameter changes
(B) less sensitive to feedback-path parameter changes than to forward-path parameter charges
(C) less sensitive to forward-path parameter changes than to feedback-path parameter changes
(D) equally sensitive to forward- and feedback-path parameter charges
38. In the system of Fig. Q38, sensitivity of M(s) = Y(s)/R(s) with respect to parameter K1 is
(A)
(B)

1
1 + K1 K2

R(s)

G(s)

K1

1
1 + K1 G ( s )

(C) 1
(D) None of the answers in (A), (B), and (C) is
Fig. Q38
correct
39. In the system of Fig. Q38, sensitivity of M(s) = Y(s)/R(s) with respect to parameter K2 is

Y(s)

K2

(A)

1
1 + K 2 K1

(B)

1
1 + K 2 G ( s)

(C)

- K 2 G (s)
1 + K2 G (s )

(D) None of the answers in (A), (B), and (C) is correct.

40. A speed control system is represented by the signal flow graph shown in Fig. Q40. The nominal value of the
parameter K is 10. Sensitivity of M(s) = w(s)/wr(s) to changes in K is
(A)

s + 0.1
s + 11

(B)

(C)

- 0.1
s + 0.2

(D) None of the answers in (A), (B), and (C) is correct.

wr(s)

s + 0.1
s + 0.2

K
10s + 1

w(s)

0.1
Fig. Q40
41. A speed control system is represented by the block diagram of Fig. Q41. The system is subjected to a step
OL
disturbance W(s). w CL
ss /w ss (the steady-state speed under closed-loop operation/steady-state speed under
open-loop operation) is equal to

Appendix-B OLC.p65

21

4/22/08, 3:45 PM

22

Control Systems: Principles and Design

W(s)

(A)
(B)
(C)
(D)

1/2
1
2
None of the answers in (A), (B), and (C) wr (s) = 0
is correct
42. The time response of the system of Fig. Q42a
to an input r(t) = 10 m(t) is shown in Fig. Q42b.
The gain K is equal to
(A) 10
(B) 8
(C) 4
(D) None of the answers in (A), (B), and (C) is correct

10
10s + 1

w (s )

0.1
Fig. Q41

K
ts + 1

O
(b)

(a)

Fig. Q42
43. An inertial and a frictional load are driven by a dc motor with torque TM. The dynamic model of the system is
TM (t) = J

d w (t )
+ Bw(t)
dt

The steady-state speed of the motor for step input will be doubled when
(A) inertia J is doubled
(B) friction B is doubled
(C) both the inertia J and friction B are doubled
(D) None of the answers in (A), (B), and (C) is correct
44. Consider the following statements:
(i) If an open-loop system is unstable, applying feedback will always improve its stability.
(ii) If an open-loop system is subject to parameter variations, applying feedback will always improve robustness.
Which of the following is the correct answer?
(A) None of the above statements is true
Y(s)
R(s)
3
4
(B) Statement (i) is true but statement (ii) is false
s+1
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
45. The characteristic equation of the closed-loop
10
system of Fig. Q45 is
s
+
10
(A) s2 + 11s + 10 = 0
(B) s2 + 11s + 130 = 0
Fig. Q45
(C) s2 + 10s + 120 = 0
(D) s2 + 10s + 12 = 0

Appendix-B OLC.p65

22

4/22/08, 3:45 PM

23

Appendix B: Control Theory Quiz

46. Which of the following describes the step response of the

Y(s)
R(s)
10
closed-loop system of Fig. Q46?
s2 + 2s + 1
(A) Underdamped
(B) Critically damped
(C) Overdamped
Fig. Q46
(D) The output does not reach a steady-state value.
47. The system of Fig. Q47 has the steady-state error
1
0.1
(B)
(A)
1.125
1.125
1.1
(C)
(D) None of the answers in (A), (B), and (C) is correct
1.125
W (s) = 1
s
R( s) = 1
s

1.25

0.1
2s + 1

Y(s)

qr

1
ts+1

Fig. Q47

Fig. Q48

48. It is desired that the output q changes by unit step with zero error at steady state (Fig. Q48). We can achieve it by
injecting
(B) qr of step size (1+K)/K
(A) qr = unit step
(D) None of the answers in (A), (B), and (C) is correct
(C) qr of step size K/(K+1)
49. Consider the system of Fig. Q49. The steady-state error is zero for
1
(B) K f =
(A) K f = 0
1.25
(C) Kf = 1.25
(D) None of the answers in (A), (B), and (C) is correct
W (s) = 1
s
Kf

R(s) = 0

0.1
2s + 1

1.25

Y(s)

Fig. Q49
SM
G

50. Sensitivity
(Fig. Q50) is

of the closed-loop transfer function M(s) with respect to open-loop transfer function G(s)

1
2 s 2 + (3 K P + 1) s + 3K I
s (2 s + 1)
(C)
2 s 2 + ( K P + 1) s + K I

(A)

Appendix-B OLC.p65

23

s (2 s + 1)
2 s 2 + ( K P + 1) s + 3K I
s (2 s + 1)
(D)
2 s 2 + (3 K P + 1) s + 3 K I
(B)

4/22/08, 3:45 PM

24

Control Systems: Principles and Design

W(s)
R(s)

Y(s)

G(s) = K P + I 3
s 2s + 1

Fig. Q50
51. For what value of K is the time-constant of the system of Fig. Q51 equal to 0.2 seconds?
(A) K = 3
(B) K = 5
(C) K = 7
(D) K = 9
52. Consider the system of Fig. Q52. The KP to move the time-constant to one sixth of its open-loop value is
0.333
0.333
(A)
(B)
6
2
6
2
(C)
(D)
0.333
0.333

R(s)

3
2s + 1

Y(s)

R(s)

10
s + 0.333

KP

Y(s)

Fig. Q51
Fig. Q52
53. Consider the system of Fig. Q53. The steady-state offset is zero when KP is
(A) zero
(B) infinity
(D) no value of KP
(C) any value of K P

W ( s ) = 0.5
s
R(s) = 0

KP

0.3
2s + 1

Y(s)

Fig. Q53
54. A proportional controller, KP, is used with a first-order system G(s) = K/(ts + 1) in unity-feedback structure.
Increasing KP will
(A) increase the time-constant and decrease the steady-state error to step inputs
(B) decrease the time-constant and decrease the steady-state error to step inputs
(C) decrease the time-constant and increase the steady-state error to step inputs
(D) increase the time-constant and increase the steady-state error to step inputs
55. Consider the system of Fig. Q55. K I that gives critical
Y(s)
R(s)
KI
0.3
damping is
s
2
s
+
1
(A) 0.417
(b) 0.257
(C) 1
(D) None of the answers in (A), (B), and (C) is
Fig. Q55
correct

Appendix-B OLC.p65

24

4/22/08, 3:45 PM

25

Appendix B: Control Theory Quiz

56. Consider the system of Fig. Q56. The steady-state offset is zero for
(B) KI =
(A) KI = 0
(D) no value of KI
(C) any value of K I
W ( s ) = 0.5
s
R(s) = 0

KI
s

0.3
2s + 1

Y(s)

Fig. Q56
57. An integral controller K I /s is used with a first-order system G(s) = K/(ts + 1) in unity-feedback structure.
Increasing KI will
(A) decrease damping with no change in steady-state offset to step commands.
(B) decrease damping with decrease in steady-state offset to step commands.
(C) increase damping with no change in steady-state offset to step commands.
(D) increase damping with decrease in steady-state offset to step commands.
58. The condition that all the roots of the polynomial
D(s) = a0s3 + a1s2 + a2s + a3; ai > 0
have negative real parts, is given by
(B) a1a0 > a2 a3
(C) a1a2 > a0a3
(A) a1a3 > a0a2
59. Consider the following statements:
(i) All the roots of the polynomial
D1(s) = 3s4 + 10s3 + 5s2 + 2
have negative real parts.
(ii) All the roots of the polynomial
D2(s) = s4 + 4s3 + 6s2 + 4s 5
have negative real parts.
Which of the following is the correct answer?
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
60. The characteristic equation of a feedback control system is given by

(D) a2 a0 > a1a3

2s4 + s3 + 2s2 + 5s + 10 = 0
The number of roots in the right half of s-plane are
(A) zero
(B) 1
(C) 2
61. The polynomial
D(s) = s3 + 3s2 + 2s + 6
has
(A) two roots in left half s-plane and one root in right half
(B) two roots in right half s-plane and one root in left half
(C) two roots on jw-axis of s-plane and one root in right half
(D) two roots on jw-axis of s-plane and one root in left half.
62. The characteristic equation of a feedback control system is
s3 + a1s2 + a2 s + Ka2 = 0; a1, a2, > 0,

Appendix-B OLC.p65

25

(D) 3

4/22/08, 3:45 PM

26

Control Systems: Principles and Design

where K is a variable positive scalar parameter. The system is stable for all values of K given by
(B) K < a2
(C) K > a1
(D) K < a1
(A) K > a2
63. The open-loop transfer function of a unity feedback system is
G(s) = K/[s2 (s + 5)]; K > 0
The system is unstable for
(A) K > 5
(B) K < 5
(C) K > 0
(D) All the answers in (A), (B), and (C) are correct
64. A unity feedback system has open-loop transfer function
G(s) = K/[s(s + 1)(s + 2)]; K > 0
The value of K that results in oscillatory response to step input, is
(A) 2
(B) 6
(C) 20
(D) 60
65. The first two rows of Routh tabulation of a third-order system are
s3

(A) The characteristic equation has one root in right half s-plane
(B) The characteristic equation has two roots on the jw-axis at s = j
(C) The characteristic equation has two roots on the jw-axis at s = 2j
(D) None of the answers in (A), (B), and (C) is correct
66. Presence of transportion lag in the forward path of a closed-loop control system
(A) decreases margin of stability
(B) increases margin of stability
(C) does not affect its margin of stability
1
2
and cascade controller D(s) = KP + . The
67. Consider a unity-feedback system with plant G(s) = 2
s
s + s +1
values of KP for which the system is stable are
(B) unstable for all KP > 0 (C) KP > 1
(D) K P > 2
(A) KP > 0
68. The error function of a feedback system is
E(s) =

( s + 0.1)( s + 0.5)
s ( s + 0.1)( s + 0.5) + 0.5( s + 1)

The steady-state value of e(t) is

(A) 0.001
(B) 0.1
(C) 0.01
(D) None of the answers in (A), (B), and (C) is correct
69. Consider the system of Fig. Q69. The steady-state error is less than 2% for step input for
(B) any value of K c
(C) no value of Kc
(D) K c >50
(A) Kc > 49

R(s)

Kc

2
s + 4 s + 5s + 2
3

Y(s)

Fig. Q69
70. A unity feedback system has open-loop transfer function G(s) = 9/[s(s + 3)]. The system has
(A) damping ratio = 1/2, and natural frequency = 9
(B) damping ratio = 1/6, and natural frequency = 3
(C) damping ratio = 1/6, and natural frequency = 9
(D) damping ratio = 1/2, and natural frequency = 3
71. A unity feedback system has open-loop transfer function G(s) = 25/[s(s + 6)]. The time tp at which the peak of the
step-input response occurs, is
(A) 11/7 sec
(B) 11/4 sec
(C) 11/14 sec
(D) 11/28 sec

Appendix-B OLC.p65

26

4/22/08, 3:45 PM

27

Appendix B: Control Theory Quiz

72. Peak overshoot of step-input response of an underdamped second-order system is explicitly indicative of
(A) settling time
(B) rise time
(C) natural frequency
(D) damping ratio
73. A unity feedback system has open-loop transfer function G(s) = 25/[s(s + 6)]. The peak overshoot in the stepinput response of the system is approximately equal to
(A) 5%
(B) 10%
(C) 15%
(D) 20%
74. The step-input response of the system of Fig. Q74a is shown in Fig. Q74b. The value of damping ratio of the
system is
(A) 0.39
(B) 0.49
(C) 0.59
(D) 0.69

K
s (s + p)

0.003

0.03

(a)

(b)

Fig. Q74
75. A unity feedback system with open-loop transfer function G(s) = 4/[s(s + p)] is critically damped. The value of
the parameter p is
(A) 4
(B) 3
(C) 2
(D) 1
76. A unity feedback system has open-loop transfer function G(s). The steady-state error is zero for
(A) step input and type-1 G(s)
(B) ramp input and type-1 G(s)
(C) step input and type-0 G(s)
(D) ramp input and type-0 G(s)
77. A unity feedback system with forward path transfer function G(s) = 1/[s2 (s + 1)] is subjected to an input
r(t) = K 1 + K2t + 12 t2 . The steady-state error of the system is
(A) infinity
(B) 1
(C) zero
(D) None of the answers in (A), (B), and (C) is correct
78. Closed-loop transfer function of a unity feedback system is given by

Y (s )
1
=
R ( s)
t s +1
System Kv is
(A) t
(B) 1/t
(C) 1
79. Closed-loop transfer function of a unity feedback system is given by

(D)

Y (s )
wn2
= 2
R ( s)
s + 2zwn s + wn2

System Kv is
(B) 1
(C)
(D) 2z/wn
(A) wn /2z
80. Consider the position control system of Fig. Q80. The value of K such that the steady-error is 10 for input
qr = 400t m(t) rad/sec, is
(A) 104.5
q
20
qr
K
(B) 114.5
s (0.1s + 1)
(C) 124.5
(D) None of the answers in (A), (B), and (C) is
correct
Fig. Q80

Appendix-B OLC.p65

27

4/22/08, 3:45 PM

28

Control Systems: Principles and Design

81. Consider the speed control system shown in Fig. Q81. Parameter variations occurring during operating conditions cause KA to modify to KA = 0.9KA . The value of KA that limits the change in steady-state motor speed due
to parameter variations to 0.1%, is
(A) 25
(B) 35
(C) 45
(D) 55

w r = const

20
0.1s + 1

KA

0.1
Fig. Q81
82. Derivative error compensation is employed in feedback control systems to
(A) increase the effective damping in the system
(B) decrease the effective damping in the system
(C) improve the steady-state response of the system
83. Tachogenerator feedback is sometimes used in position control systems to
(A) increase the effective damping in the system
(B) decrease the effective damping in the system
(C) improve the steady-state response of the system
84. Integral error compensation is employed in feedback control systems to
(A) improve damping
(B) improve speed of response
(C) reduce steady-state error
85. A temperature control system is found to have zero error to a constant tracking input, and an error of 0.5C to a
tracking input that is linear in time, rising at the rate of 40C/sec. What is the type number of the system?
(A) 0
(B) 1
.
(C) 2
(D) Type number cannot be determined from the given information
86. Poles of second-order models with the same damping ratio lie
(A) on the real axis
(B) on a radial line from the origin
(C) on the imaginary axis
(D) None of the answers in (A), (B), and(C) is correct

K wn2
to a step input depends only on
s + 2zw n s + wn2
(A) the value of the step input
(B) the value of the damping ratio
(C) the value of the gain K
(D) the parameter wn
88. Consider the system of Fig. Q88. Increasing proportional gain will
(A) increase the overshoot and decrease the steady-state error to ramp inputs
(B) decrease the overshoot and increase the steady-state error to ramp inputs
(C) increase the overshoot and increase the steady-state error to ramp inputs
(D) decrease the overshoot and decrease the steady-state error to ramp inputs
89. Consider the system of Fig. Q89. The steady-state offset is zero when
(A) KP = , KD =
Y(s)
R(s)
1
(B) KP = 0, KD = any value
KP
s(s + 1)
(C) KP = , K D = any value
(D) no values of KP and KD

87. The percentage overshoot of a second-order system G( s) =

Fig. Q88

Appendix-B OLC.p65

28

4/22/08, 3:45 PM

29

Appendix B: Control Theory Quiz

W ( s ) = 0.5
s
R(s) = 0

KP + KDs

s2

Y (s )

2
+ 0.4s + 1

Fig. Q89
90. Consider the system of Fig. Q90. R(s) and W(s) are step signals
(A) Steady-state error to R(s) is zero and to W(s) is non-zero
(B) Steady-state error to R(s) is non-zero and to W(s) is zero
(C) Steady-state error to both R(s) and W(s) is non-zero

W(s)
R(s)

Y (s )

K
s (t s + 1)

KP

KDs
Fig. Q90
91. Consider the system of Fig. Q91. The steady-state error is less than 2% to step inputs for
(A) any value of K I
(B) no values of K I
(C) KI > 50
(D) None of the answers is (A),(B), and (C) is correct

R(s)

3+

KI
s

2
s3

4s2

+ 5s + 2

Y(s)

Fig. Q91
92. A unity feedback system has open-loop transfer function G(s) = 1/s 2 . This uncompensated type-2 system
possesses a satisfactory steady-state error for
(A) step input signals
(B) ramp input signals
(C) both the step and ramp input signals
(D) none of the step and ramp input signals
93. Consider the following statements:
(i) Many systems are designed for peak overshoot in the range 5 25%.
(ii) Desired dominant closed-loop poles are usually a complex-conjugate pair.
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true (D) Both the statements are true
94. The steady-state error due to step commands can be eliminated from proportional control systems with type-0
plants by

Appendix-B OLC.p65

29

4/22/08, 3:45 PM

30

95.

96.
97.

98.

Control Systems: Principles and Design

(i) intentionally misadjusting reference input

(ii) introducing integral mode in the controller
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true (D) Both the statements are true
Consider the following statements:
(i) In a position control system, the integrating effect naturally appears in system plant.
(ii) We do not require integral control for position control systems to obtain zero steady-state error to step
disturbances in load.
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true (D) Both the statements are true
A type-1 plant is changed to type-2 feedback system by the following cascade control action:
(A) PD
(B) PI
(C) Either PD or PI
(D) Neither PD nor PI
A unity feedback system has open-loop poles at s = 2 j2, s = 1, and s = 0; and a zero at s = 3. The angles made
by the root-locus asymptotes with the real axis, and the point of intersection of the asymptotes are, respectively,
(B) (60, 60, 180) and 2/3
(A) (60, 60, 180) and 3/2
(C) (45, 45, 180) and 2/3
(D) (45, 45, 180) and 4/3
Which of the root locus plots shown in Fig. Q98 is the correct plot for a unity feedback system with open-loop
poles at s = 1 j1, and a zero at s = 2?
(A) Fig. Q98a
(B) Fig. Q98b
(C) Fig. Q98c
(D) Fig. Q98d
jw

jw

(a)

(b)
jw

jw

(c)

(d)

Fig. Q98
99. Which of the root locus plots shown in Fig. Q99 is the correct plot for a unity feedback system with open-loop
transfer function G(s) = K/[s2(s + 5)]?
(A) Fig. Q99a
(B) Fig. Q99b
(C) Fig. Q99c

Appendix-B OLC.p65

30

4/22/08, 3:45 PM

31

Appendix B: Control Theory Quiz

jw

jw

jw

(a)

(b)

(c)

Fig. Q99
100. A unity feedback system has open-loop transfer function G(s) = K(s + 1)(s + 2) [s(s + 3) (s + 4)]. For K = 10, the
closed-loop poles are
(A) all real and distinct
(B) one real and two complex conjugate
(C) all real and repeated
(D) None of the answers in (A), (B), and (C) is correct
101. Root locus plot of a feedback system as gain K is varied, is
shown in Fig. Q101. The system response to step input is
non-oscillatory for
(A) 0 < K < 0.4
(B) 0.4 < K < 6
(C) 6 < K <
(D) None of the answers in (A), (B), and (C) is correct
102. Consider the root locus plot shown in Fig. Q101.

1
K= 0.4

K= 6

Fig. Q101

K ( s + 5)
s ( s + 2)( s + 4)( s 2 + 2 s + 2)

The meeting point of the asymptotes on the real axis occurs at

(A) 1.2
(B) 0.85
(C) 1.05
(D) .75
104. Consider the root locus plot of unity-feedback system with open-loop transfer function
G(s) =

Appendix-B OLC.p65

31

G(s) =

(i) Adding a zero between s = 1 and s = 2 would move

the root locus to the left.
(ii) Adding a pole at s = 0 would move the root locus to
the right.
Which of the following is the correct answer?
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
103. Consider the root locus plot of unity-feedback system with
open-loop transfer function

jw

K ( s + 5)
s ( s + 2)( s + 4)( s 2 + 2 s + 2)

4/22/08, 3:45 PM

32

Control Systems: Principles and Design

The break away point of the root loci on the real axis occurs at
(A) 3
(B) 4.5
(C) 5.5
(D) None of the answers is (A), (B), and (C) is correct
105. The transfer function of a lag compensator is
D(s) =

1 + at s
;t > 0
1+ ts

Im

the value of a is given by

(A) a = 1
(B) a >1
(C) a <1
(D) a is any constant
106. The root locus plot of the characteristic equation

j1

45

1+ KF(s) = 0

107.

108.

109.

110.

Appendix-B OLC.p65

is given in Fig. Q106. The value of K at s = j1 is

(A) 4
(B) 1
(C) 10
(D) None of the answers in (A), (B), and (C) is
correct
Consider the following statements:
(i) A lead compensator is nothing but a PD
controller with a filter.
(ii) A lag compensator has the characteristics of a
PI controller
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is
false
(C) Statement (i) is false but statement (ii) is
true
(D) Both the statements are true
Figure Q108 shows the Nyquist plot of a unity
feedback system having open-loop transfer function
G(s) with one pole in right half of s-plane. The
feedback system is
(A) stable
(B) unstable
(C) marginally stable
Figure Q109 shows the Nyquist plot of a unity
feedback system having open-loop transfer function
G(s) with one pole in right half of s-plane. The
feedback system is
(A) stable
(B) unstable
(C) marginally stable
Polar plot of G( jw) = 1/[ jw (1 + jw t)]
(A) crosses the negative real axis
(B) crosses the negative imaginary axis
(C) crosses the positive imaginary axis
(D) None of the answers in (A), (B), and (C) is
correct

32

Re

j1

Fig. Q106
Im

w=0

w=

Re

G( jw)-plot

Fig. Q108
Im

w =
1

G( jw)- plot

w= 0
Re

Fig. Q109

4/22/08, 3:45 PM

33

Appendix B: Control Theory Quiz

2

111. Which of the polar plots shown in Fig. Q111 is the correct plot for G( jw) = 1/[( jw) (1 + jwt)]?
(A) Fig. Q111a
(B) Fig. Q111b
(C) Fig. Q111c
(D) Fig. Q111d
Im

Im
w= 0

w =

w=
Re
w
0

(a)

(b)

Im
0

Im

0
w = Re

Re

w =

(c)

(d)

Fig. Q111
112. Which of the Bode asymptotic plots shown in Fig. Q112 is the correct plot for G(s) = K/[s2 (s + 5)]?
(A) Fig. Q112a
(B) Fig. Q112b
(C) Fig. Q112c
(D) Fig. Q112d
dB

dB

6 dB/octave

40 dB/decade

12 dB/octave

60 dB/decade

w=5

log w

w=5
(a)
dB

40 dB/decade

dB

6 dB/octave
12 dB/octave

60 dB/decade

w= 1
5

log w

(b)

log w
(c)

w= 1
5
(d)

Fig. Q112

Appendix-B OLC.p65

33

4/22/08, 3:45 PM

log w

34

Control Systems: Principles and Design

113. The Bode asymptotic plot of a transfer function is given in Fig. Q113. There
(A) are no poles at the origin (B) is one pole at the origin
(C) are two poles at the origin
114. The Bode asymptotic plot of a transfer function is given in Fig. Q114. The transfer function has
(A) one pole and one zero
(B) two poles and one zero
(C) one pole and two zeros
+ 20 dB/decade

dB

12 dB/octave

dB

+ 40 dB/decade

log w

log w

6 dB/octave

Fig. Q113

Fig. Q114

115. The minimum-phase transfer function that corresponds to

the Bode asymptotic plot shown in Fig. Q115, is
1
(B) 2s + 1
(A)
2s + 1
(C)

dB
+ 20 dB/decade

1
(D) s + 1
2

1
s +1
2
116. A unity feedback system has open-loop transfer function
G(s). Polar plot of G( jw) is shown in Fig. Q116. The gain
margin (GM) and the phase margin (FM) of the feedback
system are

Appendix-B OLC.p65

34

log w

Fig. Q115
Im
0.3
w=

(A) GM = 0.3; FM = 112.33

(B) GM = 0.3; FM = 112.33
(C) GM = 3.33; FM = 67.67
(D) None of the answers in (A), (B), and (C) is correct
117. A unity feedback system has open-loop transfer function
G(s) = K/[s(1 + st )]. The gain margin of the feedback
system is
(A)
(B) 0
(C) 1
(D) None of the answers in (A), (B), and (C) is correct
118. A unity feedback system has open-loop transfer function
G(s). Bode plot of G( jw) is shown in Fig. Q118. The
feedback system has
(A) positive phase margin and negative gain margin
(B) positive phase margin and positive gain margin
(C) negative phase margin and negative gain margin
(D) negative phase margin and positive gain margin

w=2

.33
112

Fig. Q116

4/22/08, 3:45 PM

w=0
Re

Appendix B: Control Theory Quiz

119. The corner frequencies in Bode plot of the transfer
function
G(s) =

dB

6( s 2 + 10 s + 100)
s 2 (50s 2 + 15s + 1)

are
(A) 1,50
(B) 100,1
(C) 10,1
(D) None of the answers in (A), (B), and (C) is correct
120. The low-frequency asymptote in Bode plot of
G(s) =

35

log w

180

6( s 2 + 10 s + 100)
s 2 (50s 2 + 15s + 1)

log w

has a slope of
Fig. Q118
(A) 0 dB/decade
(B) 20 dB/decade
(C) 40 dB/decade
(D) None of the answers in (A), (B), and (C) is correct
121. The high-frequency asymptote in Bode plot of
G(s) =

6(s 2 + 10 s + 100)
s 2 (50s 2 + 15s + 1)

has a slope of
(A) 0 dB /decade
(B) 20 dB/decade
(C) 40 dB/decade
(D) None of the answers in (A), (B), and(C) is correct
122. If a systems gain is given as |G( jw 0 )| = 0 dB, what will happen to an input signal at the frequency w0?
(A) It will be amplified
(B) It will be attenuated
(C) There will be no output signal
(D) None of the answers in (A), (B), and (C) is correct
123. An engineer applies the input r(t) = 2 sint to a chemical process and measures the output as y(t) = 0.4 sin (t 1.55).
What are the gain and phase of the system?
(A) ( 14dB, 89)
(B) ( 8dB, 1.55)
(C) (14 dB, 1.55)
(D) ( 8dB, 89)
124. A current to pressure transducer has a gain of 10 dB and a phase of 60 at w = 10 rad/sec. An input signal
of r(t) = 5 cos(10t p/2) is injected. What is the output signal?
(A) 1.58 cos (20t 5p /6) (B) 1.58 cos (10t p /6)
(C) 1.58 cos (10t + p /6) (D) None of the answers in (A), (B), and (C) is correct
125. Bode magnitude plot of a system has 20 dB gain at low frequencies. The system is
(A) type-0
(B) type-1
(C) type-2
(D) Nothing can be deduced about type number from the given information
126. A PI controller KP + K I /s = 100 + 0.01/s has a high-frequency gain of 40dB. The values of K P and K I that reduce
high-frequency gain to 20dB are (calculations based on asymptote plot in Bode coordinates)
(i) (10,0.01)
(ii) (10,0.001)
(A) Both the statements are true
(B) Statement (i) is true but (ii) is false
(C) Statement (i) is false but (ii) is true (D) Both the statements are false
127. The frequency response of the system G (s) = etD s/s at frequency w = p/(2tD) gives magnitude and phase of
(B) 2tD /p , 180
(A) 2tD /p, 90
(D) None of the answers in (A), (B) and (C) is correct
(C) 2tD /p,0
128. A PD controller has transfer function (0.1 + 0.01s). The frequency at which the magnitude is 20dB is (calculations based on asymptotic plot is Bode coordinates)
(A) 10
(B) 1000
(C) 1
(D) 100

Appendix-B OLC.p65

35

4/22/08, 3:45 PM

36

Control Systems: Principles and Design

129. Frequency response of a system is given in the following table.

Frequency (rad/sec)
0.1
1
10
100

Gain
5
1.5
0.25
0.1

Phase (deg)
0
90
180
235

Gain margin is
(A) 4
(B) 0.25
(C) 5
130. Frequency response of a system is given in the following table.
Frequency (rad/sec)
1
10
100
1000

Gain
10
2
1
0.1

(D) 1.5

Phase (deg)
50
100
155
235

Phase margin is
(A) 25
(B) +25
(C) 55
131. Nyquist plot and Bode magnitude plot of two systems are given in Fig. Q131.
(A) Both the systems are type-0
(B) Both the systems are type-1
(C) System I is type-0 and system II is type-1
(D) System II is type-0 and system I is type-1

Im (G)

dB

w=

(D) +55

20dB/decade

w=
log w

Re (G)
20dB/decade
w
System I

System II
Fig. Q131

132. Consider the following statements for an underdamped second-order system:

(i) Peak overshoot in step-input response reduces as damping is increased from 0.2 to 0.6.
(ii) Resonance peak in frequency response reduces as damping is increased from 0.2 to 0.6.
Which of the following is the correct answer?
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
133. Undamped natural frequency w n and resonance frequency w r of a unity feedback system with open-loop transfer
function

Appendix-B OLC.p65

36

4/22/08, 3:45 PM

Appendix B: Control Theory Quiz

G(s) =
are related as
(A) wn = wr
(C) w n < wr

w n2
;z<
s ( s + 2z w n )

(B) wn > wr
(D) None of the answers in (A), (B), and (C) is correct

134. For a unity feedback system with open-loop transfer function G(s) =

135.

136.

137.
138.
139.
140.

141.

142.

Appendix-B OLC.p65

37

w n2
, z < 0.7;
s ( s + 2 z wn )

(i) phase margin is explicitly indicative of damping ratio;

(ii) resonance peak is explicitly indicative of damping ratio.
Which of the following answers is correct?
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
Open-loop transfer function of a unity feedback system is G(s) = K/[s(s + 5)]. The gain K that results in a phase
margin of 50 is approximately
(A) 15
(B) 20
(C) 25
(D) 30
K
. Increase in gain K will
Consider a unity-feedback system with open-loop transfer function G(s) =
s ( s + 1)
cause:
(A) the gain crossover frequency to reduce
(B) the gain crossover frequency to increase
(C) the system to respond more slowly
(D) None of the statement in (A), (B), and (C) is
correct
The closed-loop dynamics of a system is of second-order. To improve the damping, we should
(A) decrease the phase margin
(B) increase the phase margin
(C) decrease the gain margin
(D) increase the gain margin
The vertical axis of the Nichols chart represents
(A) open-loop gain
(B) open-loop phase
(C) closed-loop gain
(D) closed-loop phase
M-Contours on the Nichols chart represent
(A) open-loop gain
(B) open-loop phase
(C) closed-loop gain
(D) closed-loop phase
Consider the following statements
(i) The resonance peak of the frequency response of G/(1+ G) is given by the M-contour on the Nichols chart
which is tangent to the Nichols plot of G.
(ii) The resonance peak of the frequency response of G/(1+ G) is the peak value of the frequency response of
G/(1+ G) on Bode magnitude plot.
(A) Both the statements are true
(B) Statement (i) is true but (ii) is false
(C) Statement (i) is false but (ii) is true
(D) Both the statements are false
The closed-loop dynamics of a system is of second-order. The resonance peak of the closed-loop frequency
response is related to
(i) overshoot of time response
(ii) damping ratio
(A) Both the statements are true
(B) Statement (i) is true but (ii) is false
(C) Statement (i) is false but (ii) is true
(D) Both the statements are false
The bandwidth of G/(1+G)
(i) is the frequency at which the 3 dB M-contour on Nichols chart intersects the Nichols plot of G.
(ii) is the frequency at which the Bode magnitude plot of G/(1+G) has a gain of 3 dB.
(A) Both the statements are true
(B) Statement (i) is true but (ii) is false
(C) Statement (i) is false but (ii) is true (D) Both the statements are false

37

4/22/08, 3:45 PM

38

Control Systems: Principles and Design

143. A unity-feedback system has open-loop transfer function

G(s) =

w n2
s ( s + 2z w n )

(i) The peak overshoot of step-input response of G/(1+G) is indicative of damping

(ii) The resonance peak of frequency response of G/(1+G) is indicative of damping.
(A) Both the statements are true
(B) Statement (i) is true but (ii) is false
(C) Statement (i) is false but (ii) is true (D) Both the statements are false
144. For the system 1/(s2 + 0.1s + 1), the resonance frequency wr and natural frequency wn are related as
(B) wr > wn
(A) wr = wn
(C) wr < wn
(D) None of the answers in (A), (B), and (C) is correct
145. Maximum phase-lead of the compensator D(s) = (0.5s + 1) (0.05s + 1), is

146.

147.

148.

149.

(A) 52 at 4 rad/sec
(B) 52 at 10 rad/sec
(C) 55 at 12 rad/sec
(D) None of the answers in (A), (B), and (C) is correct
In control systems
(i) reduction in bandwidth results in sluggish response;
(ii) reduction in bandwidth results in better signal/noise ratio.
Which of the following is the correct answer?
(A) None of the above statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
Consider the following statements:
(i) Lead compensation is suitable for systems having unsatisfactory transient response. It also provides a limited improvement in steady-state response.
(ii) Lag compensation is suitable for systems with satisfactory transient response but unsatisfactory steadystate response.
Which of the following is the correct answer?
(A) None of the statements is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true
(D) Both the statements are true
Consider the following statements:
(i) The natural frequency w n must be large for good performance; however, bandwidth considerations impose
a limit on increasing wn.
(ii) When design considerations impose a limit on wb, a PD compensator with a filter is suitable.
(A) None of the above statments is true
(B) Statement (i) is true but statement (ii) is false
(C) Statement (i) is false but statement (ii) is true (D) Both the statements are true
Consider the sampled-data system shown in Fig. Q149. Steady-state error for unit-ramp input is
1
T
(B)
(A)
KT
K
(C)

1
K

(D) None of the answers in (A), (B), and (C) is correct

r
T

Zeroorder
hold

K
s(t s + 1)

Fig. Q149

Appendix-B OLC.p65

38

4/22/08, 3:45 PM

Appendix B: Control Theory Quiz

39

150. In a digital control system, selection of a large sampling period

(A) increases the stability margin
(B) decreases the stability margin
(C) has no effect on stability
(D) has an effect on stability that depends on plant
parameters
151. In a digital control scheme, selection of a large sampling interval
(A) improves the steady-state performance
(B) deteriorates the steady-state performance
(C) has no effect on steady-state performance
(D) has an effect on steady-state performance that
depends on plant parameters
152. In a sampled-data control system, delay introduced by sampling and reconstruction process is approximately
equal to
(A) sampling interval
(B) twice the sampling interval
(C) half the sampling interval
(D) None of the answers in (A), (B), and (C) is
correct
153. Given a state variable model
N = )N+ >u
y = ?N + du
Under the transformation N = 2 N ; 2 a constant nonsingular matrix, the model becomes

N = ) N + > u
y = ? N + du
(A) ) = 2)2`; > = 2`>; ? = ?2

(B) ) = 2`)2; > = 2`>; ? = ?2

(C) ) = 2`)2; > = 2>; ? = ?2

(D) ) = 2`)2; > = 2>; ? = ?21
154. A state variable formulation of a system is given by the equations

x1
-1 0 x1 1
x = 0 - 3 x + 1 u

2
2
y = [1
The transfer function of the system is
1
(A)
( s + 1) ( s + 3)

x1
0]
x2
(B)

1
s +1

1
(D) None of the answers in (A), (B), and (C) is correct
s+3
155. A state variable formulation of a system is given by the equations

(C)

x1
-1 0 x1 1
x = 0 - 3 x + 1 u ; x1(0) = x2 (0) = 0

2
2
x1
y = [1 0]
x2
The response y(t) to unit-step input is
1
(1 e3t)
3
(D) None of the answers in (A), (B), and (C) is correct

(A) 1 + et

(B)

(C) 1 et

Appendix-B OLC.p65

39

4/22/08, 3:45 PM

40

Control Systems: Principles and Design

156. The eigenvalues of the matrix

1
0
0
) = 0
0
1
0 - 3 - 4

are
(A) 0, 1, 3
(C) 0, 0, 4
157. Given the system

(B) 0, 3, 4
(D) None of the answers in (A), (B), and (C) is correct
0 0 - 20
3
N = 1 0 - 24 N+ 1 u
0 1 - 9
0

y = [0

1]N

The characteristic equation of the system is

(A) s3 + 20s2 + 24s + 9 = 0
(B) s3 + 9s2 + 24s + 20 = 0
(C) s3 + 24s2 + 9s + 20 = 0
(D) None of the answers in (A), (B), and (C) is correct
158. A state variable model of a system is given by

x1
1 1 x1 0
x = - 2 -1 x + 1 u

2
2
x1
y = [1 0]
x2
The system is
(A) controllable and observable
(C) observable but uncontrollable
159. The transfer function

(B) controllable but unobservable

(D) uncontrollable and unobservable

G(s) = ?(s1 ))1>

of the system

N = )N+ >u
y = ?N+ du
has pole-zero cancellation. The system
(A) is uncontrollable and unobservable
(C) is controllable but unobservable
160. The transfer function

(B) is observable but uncontrollable

(D) may be any one of (A), (B), and (C)

G(s) = ?(s1 ))1>

of the system

N = )N + >u
y = ?N + du
has no pole-zero cancellation. The system
(A) is controllable and observable
(C) is controllable but unobservable

Appendix-B OLC.p65

40

(B) is observable but uncontrollable

(D) may be any one of (A), (B), and (C)

4/22/08, 3:45 PM

41

Appendix B: Control Theory Quiz

161. Consider the system
1
0
0
0
) = 0
0
1 ; > = 0 ; ? = [4
- 6 -11 - 6
1

1]

The transfer function of the system has pole-zero cancellation. The system is
(A) controllable and observable
(B) uncontrollable and unobservable
(C) controllable but unobservable
(D) observable but uncontrollable
162. Consider the system

0 - 2
1
)=
; > = 1 ; ? = [0 1]
1
3

The transfer function of the system has pole-zero cancellation. The system is
(A) controllable and observable
(B) uncontrollable and unobservable
(C) controllable but unobservable
(D) observable but uncontrollable
163. In a control system design exercise for a marine engine, an engineer is using the state-space framework. The
system model is given by
13/ 6 4 / 3
0
N + >u ; > =
N =

-4 / 3 -7 / 6
0.5
The engineer decides to experiment with a different method of actuation for the system and this leads to the
different input matrix
-1/ 6
>1 =

1/ 3
(A) Both the systems are controllable
(B) System with input matrix >is controllable, and it becomes uncontrollable when > is changed to >1
(C) System with input matrix > is uncontrollable and it becomes controllable when > is changed to >1
(D) Both the systems are uncontrollable
164. Given the state variable model {),>,?} of a single-input, single-output system.
The asymptotic stability is determined from
(A) ),> and ? matrices
(B) ) and > matrices
(C) ) and ? matrices
(D) ) matrix

Master Key
1.
5.
9.
13.
17.
21.
25.
29.
33.
37.
41.
45.
49.

Appendix-B OLC.p65

(C)
(A)
(D)
(D)
(A)
(D)
(C)
(B)
(D)
(C)
(A)
(B)
(B)

2.
6.
10.
14.
18.
22.
26.
30.
34.
38.
42.
46.
50.

41

(C)
(B)
(A)
(A)
(D)
(A)
(A)
(C)
(C)
(C)
(C)
(A)
(D)

3.
7.
11.
15.
19.
23.
27.
31.
35.
39.
43.
47.
51.

(C)
(A)
(C)
(A)
(A)
(C)
(B)
(B)
(D)
(C)
(D)
(C)
(A)

4.
8.
12.
16.
20.
24.
28.
32.
36.
40.
44.
48.
52.

4/22/08, 3:46 PM

(D)
(B)
(D)
(D)
(C)
(B)
(B)
(A)
(B)
(B)
(C)
(B)
(A)

42
53.
57.
61.
65.
69.
73.
77.
81.
85.
89.
93.
97.
101.
105.
109.
113.
117.
121.
125.
129.
133.
137.
141.
145.
149.
153.
157.
161.

Appendix-B OLC.p65

Control Systems: Principles and Design

(B)
(A)
(D)
(B)
(C)
(B)
(B)
(D)
(B)
(C)
(D)
(B)
(A)
(C)
(B)
(A)
(A)
(C)
(A)
(A)
(B)
(B)
(A)
(D)
(C)
(B)
(B)
(C)

54.
58.
62.
66.
70.
74.
78.
82.
86.
90.
94.
98.
102.
106.
110.
114.
118.
122.
126.
130.
134.
138.
142.
146.
150.
154.
158.
162.

42

(B)
(C)
(D)
(A)
(D)
(C)
(B)
(A)
(B)
(B)
(D)
(B)
(D)
(A)
(D)
(C)
(B)
(D)
(A)
(B)
(D)
(A)
(A)
(D)
(B)
(B)
(A)
(D)

55.
59.
63.
67.
71.
75.
79.
83.
87.
91.
95.
99.
103.
107.
111.
115.
119.
123.
127.
131.
135.
139.
143.
147.
151.
155.
159.
163.

(A)
(A)
(D)
(C)
(C)
(A)
(A)
(A)
(B)
(D)
(B)
(C)
(D)
(D)
(C)
(D)
(D)
(A)
(B)
(C)
(C)
(C)
(A)
(D)
(C)
(C)
(D)
(B)

56.
60.
64.
68.
72.
76.
80.
84.
88.
92.
96.
100.
104.
108.
112.
116.
120.
124.
128.
132.
136.
140.
144.
148.
152.
156.
160.
164.

4/22/08, 3:46 PM

(C)
(C)
(B)
(D)
(D)
(A)
(B)
(C)
(A)
(D)
(B)
(A)
(D)
(A)
(B)
(C)
(C)
(D)
(B)
(D)
(B)
(A)
(C)
(D)
(C)
(A)
(A)
(D)