Soubor 1 5 1 8 Cpds Obsluha 60

OPERATION & SERVICE
MANUAL
Three-wheel Electric Forklift Truck
KION Baoli (Jiangsu) Forklift Co., Ltd.
PREFACE
Three-wheel electric forklift trucks are designed on the base of advantages of some
trucks made by domestic and foreign manufactures and developed in introduced
technology from abroad. These trucks are all suited for handling and stacking packed
goods in stations, ports, goods yards and warehouses and used widely in food processing,
light and textile, mining industries and other factories, with some of attachments fitted, the
trucks can be applied more and more.
These forklift trucks feature a wide-vision mast, full powered steering unit,
self-energizing brake, stepless speed control and high quality Italian AC system controllers,
Italian drive unit (self-energizing brake), multi-functional LCD instruments, importing
components as hydraulic AC motor with temperature and speed sensor and towing AC
motor, so they have a lot of advantages such as good performance, easy operation, wide
vision, flexible steering, reliable braking, powerful, low noise, no contamination and
aesthetic appearance.
This manual states the forklift trucks specifications, operation, maintenance, main
assemblies constructions and working principles so as to help operators to use the trucks
correctly and attain the highest functions. It is necessary to read over the manual before
operating or maintaining the forklift trucks. The rules and notices in this manual should be
abided seriously by all relative personnel to enable these trucks in optimized working state
for long period and bring the highest efficiency.
The partial content in this manual might not correspond with the actual condition
because of technical improvement. Our products are subject to improvements and
changes without notice.
CONTENTS
. External view and main specification 1
. Safety instruction, operation & maintenance of electric forklift truck 3
2.1 Shipping, loading, unloading and slinging 3
2.2 Storage of forklift truck 4
2.3 Precautions before operation 4
2.4 Information of safety operation 4
2.5 Periodic servicing and maintenance of electric forklift truck 8
2.6 Brief operation instruction 11
2.7 Caution plates 14
. Construction, principle, adjustment and maintenance of forklift truck
20
1. Transmission system 20
1.1 General description 20
1.2 Disassembly of drive system 22
1.3 Assembly of drive system 23
1.4 Replenishing with gear oil 25
2. Brake system 26
2.2 Maintenance and adjustment of brake system 29
3. Steering system 31
3.2 Adjustment and maintenance 36
4. Electric system 37
4.2 SME compact meter 39
4.3 SME AC electric control assy 43
4.4 Distribution and setting of sensor 44
4.5 AC microtron 46
5. SME three-phase AC motor 48

5.2 Operating environment 48
5.3 Daily inspection and maintenance 48
6. Battery and charger 49
6.1 Structure of battery 49
6.2 Specification of battery 49
6.3 Usage and maintenance of battery 49
6.4 Troubleshooting 54
6.5 Charger 55
7. Hydraulic system 58
7.2 Maintenance and adjustment of hydraulic system 69
8. Mast system 74
8.2 Maintenance and adjustment of mast system 77
Charging record card of electric forklift truck 80

NOTE 81
EC DECLARATION OF CONFORMITY
82
. External view and technical parameter
External view of three-wheel electric forklift truck
Power & Control
Chassis
Performance
Dimension
General
Technical parameter
Model
Rated capacity
Load center
Power type
Tyre
No. of tyre(front/rear)
Lift height
Free lift height
Fork size
Mast tilt angle (forward/backward)
Length to fork face
Overall width
Overall
Mast lowered height
dimension
Mast extended height
Overhead guard height
Turning radius
Front overhang
Min. right angle stacking aisle width
(pallet 8001200,10001200)
Travel speed
Full load
/no load
Lifting speed
Grade ability(full load)
Service weight (including battery)
Max. pulling force
Front
Tyre
Rear
Front
Tread
Rear
Wheel base
Mast
Min. ground clearance
(full load/no load)
Frame
Type
Battery
Voltage
Capacity
Drive motor
motor
Hydraulic motor
kg
mm
H
H4
LWT
/
L1
B1
H1
H3
H2
R
X
mm
mm
mm
deg
mm
mm
mm
mm
mm
mm
mm
RASA
mm
km/h
mm/sec
%
kg
KN
B2
B3
Y
M
F
mm
mm
mm
mm
mm
V
Ah
Kw/rpm
Kw/rpm
Controller
CPDS15
1500
CPDS18
1750
500
Battery
Super elastic solid tyre
2/2
3000
3000
130
130
92010040
5/7
1860
1910
1070
1980
3945
1990
1500
360
2860/3060
2910/3110
14/15.5
13.5/15
300/470
20
3100
3260
14.5
13
187-8 PR
166-8 PR
895
205
1295
80/85
75/85
100/110
Lead-acid plates
48
505
26.5/1500
12/2200
Italian SME AC Controllers
. Safety instruction, operation & maintenance of electric forklift truck

It is important for drivers and managers to remember the principle of safety first and
ensure the safety operation as the description of Operation & Service Manual. Please read
this manual thoroughly. This will give you a complete understanding of Baoli forklifts and
permit you to operate them correctly and safely.
2.1 Shipping, loading, unloading and slinging

2.1.1 Ship the forklift truck
(1) Apply the parking brake when shipping the forklift trucks by container or freight car.
(2) Fix the mast and the balance weight with steel wire and use jacks to prevent the
forklift trucks from moving in the cabin.
(3) Pay attention to the overall length, width, height when loading, unloading and
shipping and conforming the regulations is necessary.
2.1.2 Load and unload the forklift truck
(1) Use the plate with enough length, width and strength.
(2) Pull the parking brake and use jacks to stop the wheel.
(3) Fasten the plate on the center of the cabin, there must be no grease on the plate.
(4) The left and right height of the plate must be equal to make the loading and
unloading smooth.
(5) Dont change the direction on the plate to prevent the danger.
(6) Reverse the truck slowly when loading the forklift truck on the freight car.
2.1.3 Sling the forklift truck
(1) Only the specially trained personnel can sling the truck.
(2) Sling points should be always at the positions specified in sling nameplate.
(3) The slinging cable must be enough to hang the forklift truck.
(4) Disassembled parts of forklift truck must be slung in the appointed position.
(5) Single transporting if necessary after disassembling the mast and balance weight.
Model
Unit
CPDS15
CPDS18
Specification
Max. outline size mm
362810.51066 402810.51066
Balance weight
Slinging capacity
kg
>600
>800
Max. outline size mm 106613221550 106613221550
Overhead guard
Slinging capacity
kg
>100
>100
Max. outline size mm
36110662130
36110662130
Mast
(Lifting height 3000mm) Slinging capacity
kg
>600
>600
Notice:
Dismantling and slinging the component shall not be performed without the
approval of our company. Under special circumstances, the appointed sling position
should be used. The balance weight, fork and mast of the truck all have their appointed
hang up position. The above mentioned capacity is only for a reference, which may be
adjusted because of configuration difference or technology optimization.
2.2 Storage of forklift truck

(1) Lower the mast to the lowest position.
(2) Turn off the key switch, place the levers in the neutral position. Disconnect the
power plug.
(3) Apply the parking brake.
(4) Wedge up the front and rear wheels.
(5) If the truck leaves unused for long time, build the wheels on stilts. Charge the
battery once a month.
2.3 Precautions before operation.

(1) Check all the instruments.
(2) Check the tyre inflation pressure.
(3) Check all the levers and pedals.
(4) Check if the voltage of the battery is in normal limit. Check if the density and level
of the electrolyte is appropriate.
(5) Check for all the terminals and plugs.
(6) Check hydraulic oil, electrolyte and brake fluid for leakage.
(7) Check all connectors and fasteners for looseness.
(8) Check if all the lamps and signals are in normal state.
(9) Release the parking lever.
(10) Make trial of the mast for lifting and lowering, forward and backward tilting, and
the truck for steering and braking.
(11) The contamination level of the hydraulic oil should be lower than grade 12.
2.4 Information of safety operation

(1) The forklift truck belongs to special equipment. Only trained and authorized
operator shall be permitted to operate and service the truck.
4
(2) Wear the safety guards, such as clothing, shoes, helmet and gloves while
operating the truck.
(3) When the distance between the gravity center of loads and the fork arms is 500mm,
the max. capacity is the rated capacity. When the distance exceeds 500mm, the capacity
shall be based on the load chart. Handle only loads within the allowable capacity of the
truck. The goods handled should not exceed the rated capacity of the truck.
(4) Operate your truck on a hard ground. Operate on other ground, the lift capacity and
travel speed must be decreased. Wipe off the oil and grease on the floor.
(5) Daily maintenance services should be done before or after using the truck. Anytime
you find that the truck is not functioning normally, operation of the truck should be halted
and check or repair at once.
(6) When operate one lever, dont shift another lever. Dont operate the lever at any
position out of the driver seat.
(7) Dont handle unfixed or loose goods. Be careful to handle bulky goods. To prevent
the collapse of stacked goods, tighten them. Forbid loading loose or little volume goods
without tray.
(8) If the truck is equipped with a load-handling attachment, its usage sphere will be
wider, but its allowable load and stability is reduced. The attachment and special device is
not to be diverted to any other purpose. Its very dangerous to rebuild the attachment.
Please read the additional instruction we supplied and operate the truck following it strictly.
(9) Fork can not be used to pull out any embedded goods, if necessary, the pulling
force should be estimated.
(10) Insert forks deeply under goods. Adjust forks distance according to the dimension
of goods. Make the loads distribute on the forks evenly to avoid tilt and slide of goods.
Dont pick the loads with one fork tip.
(11) When handling bulky loads which restrict your vision, operate the forklift truck in
reverse or have a guide.
(12) When loading the goods, lower the forks to the floor. After the fork inserting
stacked goods, the fork arms should be in contact with the goods. Drive the truck with mast
tilting back for stabilizing the load. Before traveling, raise the forks for 200mm-300mm from
the floor.
(13) While masts lifting and lowering, anyone is absolutely prohibited from standing
under the lifting rack or being lifted with forks. Never permit anyone to stand or walk under
upraised forks.
5
(14) When loading and unloading goods, keep the mast vertical and the truck is in
braking state.
(15) Because the rear wheels steer your truck, the rear end swings wide when you
turn. Use care in aisles and other tight places.
(16) During operation, pay attention to the performance and condition of machinery,
hydraulic, electric and speed adjuster.
(17) Connect the power source, turn on the key switch, select the position of
directional switch, check the truck for normal operation by turning steering wheel, depress
the accelerator pedal softly to keep proper acceleration.
(18) When the voltage drops below 43.2V during operation with load, its necessary to
charge the battery or replace a full charged battery at once.
(19) The shift distance of control valve lever can control the speed of the lifting or
descending of the goods. When the goods are lifted or descended, the initial speed
shouldnt be too fast in either case.
(20) It is necessary to brake before tilting the mast forward or backward. Its also
necessary to decelerate and tilt forward slowly so as to prevent the goods from slipping off
the rack.
(21) Tilt the mast of the high lift forklift truck as backward as possible when the truck
works. Use minimum forward and backward tilt when loading and unloading. It is
dangerous to travel or turn at high levels.
(22) On the high lift forklift truck with lifting height more than 3m, it is noted that the
goods on it will fall down, take the protection measures if necessary.
(23) The overhead guard is main part which is strong enough to meet safety standard,
and protect the operator from falling materials. Its very dangerous to dismantle or rebuild
the overhead guard, because these conditions could lead to an accident.
(24) A load backrest shall be used as protection against back falling objects on the fork.
Its very dangerous to dismantle or rebuild the load backrest, because these conditions
could lead to an accident.
(25) Load should be contacting with a load backrest. Do not handle the load which
exceeds height of a backrest. When loads go over the load backrest, there is a danger of
loads falling against operator.
(26) The stability of the truck is influenced by the wind-force during outside operation,
you must notice specially.
(27) Be careful and slowly driving over a dock board or bridge-plate.
6
(28) When travel with load, dont tilt mast forward, dont do handling. Dont brake
abruptly to prevent the bulk from slipping off the forks.
(29) Drive the forklift truck to the stacked goods at a low speed, at the same time, pay
much attention to sharp and hard objects which may prick the tyres.
(30) Pay attention to pedestrian, obstacle and bumpy road when driving. Pay attention
to the clearance over the forklift truck.
(31) Keep your head, hands, arms, feet and legs within the confines of the operators
compartment. Never allow other persons on the forklift truck.
(32) Crossing, turning and tilting shall not be taken on a slope. It could cause sideways
turning of the truck, it is very dangerous. On a slope, drive the truck with load forward to
ascend and backward to descend. When the truck goes down on a slope, drive slowly with
the brakes on. Make sure that the engine should not be shut down when traveling on a
slope.
(33) The starting, turning, driving, braking and stopping of the truck should be done
smoothly. When steering on the humid or slippery road, the truck should be decelerated.
(34) When operating the truck, avoid sudden stop, acceleration, stop or turn. In the
case of improper operation, the truck will turn over. In case of this, the driver must keep
calm, dont jump off the truck. The driver must hold tightly the steering wheel with two
hands; meanwhile, his body must incline in opposite direction of trucks turning over.
(35) The unloaded forklift truck with attachment should be operated as a loaded truck.
(36) Check the chains periodically to make sure that good lubrication condition exists
between the chain elements, the degree of tightness between left and right chain is
identical. When there is damage on the chain during operation, if the variation value of the
chain pitch exceeds 2% of standard value, it indicates that the chains have been worn
excessively and they must be replaced immediately.
(37) To ensure the safety of loading, dont put the truck into reverse gear before it
decelerating and stopping.
(38) Dont make a sudden braking when the truck traveling with loads.
(39) When leaving, lower the forks on the ground and let the shift lever on neutral, cut
down the electric supply. If parking on a slope is unavoidable, apply the parking brake and
wedge the wheels specially stopping for long time.
(40) When tilting the mast forward or backward to the limit or lifting the fork to the
maximum height, make the directional lever back to neutral position.
(41) Dont adjust the control valve and relief valve at will to prevent the damage of
7
hydraulic system and its components because of excessive pressure passing them.
(42) According to the Directive 2000/14/EC and based on EN12053 standardwhen
the forklift truck during the test of lifting, traveling and idling, but the noise of the forklift truck
may fluctuate due to different operation and the influence of the external environment.
(43) The driver feels the vibration of the forklift truck when operating and traveling the
forklift truck. According to ISO3691 and based on EN13059 standard. The vibration of the
forklift truck fluctuates according to environment condition. In normal working condition, the
vertical direction acceleration mean value from the seat to the operator is referred to the
following table. But the vibration frequency felt by the driver depends on the working
condition (etc. road, operation method), so the actual vibration frequency must be
determined according to environment condition when necessary.
Model
CPDS15-18
The noise pressure level at
The vertical direction acceleration mean
the operators position
value from the seat to the operator
EN 12053
EN 13059
78.9dB(A)
0.87(m/s2)
(44) Users select Lengthening fork in order to carry widening loads. Pay much
attention not to overload and observe the allowable load and the capacity chart on the truck.
Careful driving should be taken when traveling and turning.
(45) When operating the machine, observe and follow all markings on the machine.
The marking plates must be replaced if lost or damaged on time.
(46) The forklift truck must be used under the following environment: below an
elevation of 1000 meters and temperature between -15 and 35, relative humidity is 95%.
Careful operation must observe under other adverse circumstances.
(47) To prevent the fire, accident or other unpredictable event, prepare the fire
extinguisher in advance and operate it according to the instructions.
(48) You cant change or add other working equipments on the truck without our
companys permit, or the rated capacity and safety operation will be affected.
(49) Check for the fastener of overhead guard, lift-descend device, adjust the roller
clearance and do the lubrication maintenance, check the chain, pulley and do the
lubrication maintenance, and lower the device to the lowest position. Please pay more
regard to safety when maintaining the upper mentioned parts for that they are on high
position.
2.5 Periodic servicing and maintenance of electric forklift truck

8
During operating the forklift truck, it is necessary to operate carefully, service and
maintenance periodically to make the forklift truck keep in good condition.
2.5.1 Handling a new forklift
The performance and service life of forklift depends heavily upon the way you service
it during the run-in period. Pay much attention in the period.
Replace gear oil in the differential and reducer after the new forklift working for 1000
hours, and then retighten all the tightness.
2.5.2 Cautions for starting
(1) The amount of hydraulic oil: The oil level should be at the middle position between
the upper and lower scale marks of oil level meter.
(2) Check the pipes, joints, pumps and valves for leak and damage.
(3) Check the traveling brakes: The free stroke of brake pedal is 20-30 mm; when
achieving effective brake, the clearance between the front floor and the pedal should be
more than 20mm.
(4) Check the parking brake: The unload truck can park on stated ramp, when the
parking lever is pulled to the bottom.
(5) Check the meters, lamps, connectors, switches and electric circuit if they are
running properly.
2.5.3 Charging the battery
(1) Please refer to Manual of Battery about the initial charging and normal charging of
the battery.
(2) When the truck working with load, the voltage of the battery reduces to 43.2V, or
the voltage of each cell drops below 1.80V, the warner of battery capacity flashes, stop the
truck until charge the battery or replace a full charged battery.
(3) Measure the density, level and temperature of the electrolyte.
(4) After the battery is used, it should be charged immediately, the time left idle of the
battery must be less than 24 hours. You should try to prevent them from over being
discharged or over charged. Either way will affect their service time and functions.
Refer to Manual of Battery about charging method and maintenance.
2.5.4 Essentials of servicing
(1) Some critical components must be replaced according to demands periodically.
Use genuine parts supplied by our company only.
(2) Use the same type of oil only when replacing or adding.
(3) If any damage or fault is found, stop the truck and report the matter to the
9
serviceman. Only trained and authorized serviceman shall be permitted to service the truck.
Do not operate the truck until the truck has been repaired completely.
(4) Maintain and service the motor, electric controller and battery separately according
to their manuals.
(5) Check all plugs once a month.
(6) Dont wash the truck with a water syringe. Using the truck outside in rainy day is
forbidden.
(7) Clean the dust of photoelectric coupler of the hydraulic motor switch.
(8) Clean and dry the surface of the battery usually.
(9) Periodic maintenance must be done according to the following list after using the
forklift truck.
No.
Item
1
2
3
4
Bearing, steering wheel

Parking brake lever
Pin, foot brake
Reduction box
Replace grease
Add grease
Add grease
Replace gear oil
Braking oil
Add
Pin, tilting cylinder

Hydraulic oil tank and
filter
Hydraulic oil
Lift chain
H. P. hose
Switch, hydraulic motor
Add lubricating grease
7
8
9
10
11
Period
(hrs.)
1000
200
200
2400
Whenever
necessary
400
Contents
Clean
1000
Replace
Replace
Replace
Clean photoelectric coupler
1000
3000
3000
200
Remark
If damaged,
replace it.
Notice: When serving and checking the truck, do not use the mast or the load
backrest as a ladder, these actions will lead to a danger unexpectedly.
2.5.5 Recommended oil and grease
Name
Brand or code
Amount
Remark
ISOVG30
24L
To the dipstick
level
SAE80W
0.550.65
To the oil level
Domestic
Overseas
Hydraulic oil
HM32#(winter) or
HM46#(summer)
Gear oil
GL-5 80W
Brake fluid
DOT3 Compound brake fluid
0.6L
Lubricant
grease
3# Lithium base grease

JISK2220/2#
(drop point 170)
Right amount
10
Adding oil, grease and brake fluid should follow relevant automobile standard. The
waster of the forklift truck must be reclaimed obeying the relevant laws and regulations.
Incorrect treatment will pollute water, soil and atmosphere etc. Wear safety guards such as
helmet, safety shoes and working clothes to avoid directly contacting with body when
adding oil, grease and brake fluid.
2.6 Brief operation instruction

2.6.1 Operation device and meter
11
Function and working condition of operation device:

No.
Name
Function
Parking brake
Park the truck.

Control head
combination lamp,
headlamp,
lamp.
Adjust handrear
wheels
angle. traveling
Change
direction.
Lamps switch
3
4
Adjust lever, hand

wheel
Shift lever
Horn button
Control the horn.
Operating lever,
turning lamps
Key switch
Indicate turning
direction.
Control electrical
system.
Meter panel
11
12
13
Lock, battery cover
Lock the battery cover
14
Foot brake pedal
Brake the truck.
10
Pull the lever backward fully.

Push or pull the double-shift
switch when lighting.
Pull the lever forward, the truck
travels forward.
The horn sounds when
pressing the button.
Pull operating lever when
turning.
Connect the meter and power
when turning right (shift).
Refer to Chapter of Electric System in this manual.
Operating lever,
tilt cylinder
Operating lever,
lift cylinder
Seat adjust lever
Accelerator pedal
Working condition
Operate tilt cylinder.

Control lift cylinder.
Adjust seat position.
Control output voltage.
Tilt backward when pulling

backward, its forward
oppositely.
Mast
lifts when pulling
backward, descends when
pushing forward.
Press and accelerate.
Press the rear button of battery
cover to open the lock
Depress the pedal to brake.
2.6.2 Operating manual

(1) Start: Before starting, put the hand brake switch on the brake position, the shift
direction switch and seat switch on neutral. If not, the safe circuit plays its part, and then
the forklift truck cant start.
Turn the start switch (electric lock) clockwise to shift to turn on the power, meter
indicator and electric control circuit, release the hand brake switch.
Push the shift direction switch forward, press down the accelerator pedal, then the
truck goes forward. If pull the direction switch backward, the reverse lamps light and the
back-up buzzers sound. If having operational errors or others, the meter will show different
error codes, some common features as follows:
If pressing down the accelerator pedal first, then turning on the direction switch, the
meter will show code 64 expressing start error.
When turning on the key switch, meter shows error code 50, it expresses that the lift is
in the state of starting.
If safe indicates on the meter, seat switch may be on.
If the voltage of the battery is too low, the error code 12 will indicate.
The common error code 90, it shows failed steering sensor, which maybe have been
12
damaged or loosen.
(2) Light switch: There are two switches on the left side of the meter. Press the right
switch, the front combination lamp lights; press the left switch, the rear combination lamp
lights.
(3) Steering signal: Pull the steering lamp switch backward, the front lamp and rear up
and down combination lamp turning signals on the left side of the truck light; pull the
steering lamp switch forward, the front lamp and rear up and down combination lamp
turning signals on the right light, and the corresponding steering lamps will flash.
(4) Brake signal: When braking, press down the brake pedal to turn on the rear
combination brake lamps (red).
(5) Reverse signal: When reversing, pull the direction switch backward, then the travel
motor reverses, rear combination reversing lamps (white) light and the back-up buzzers
sound.
(6) Press E/S/H or tortoise key on the right of the meter, the operating mode and
speed will be adjusted too.
2.6.3 Maintenance of control system
During using the electric forklift truck, its necessary to maintain the control system
periodically as follows:
(1) Check the contact terminal for wear status and contactor if works freely. Check the
contact point every three months.
(2) Check foot pedal or micro-switch of levers. Measure the voltage drop between the
contact terminals with multimeter to make sure there is no resistance between terminals.
Make sure that the sound of turning on or off the micro-switch is slivery. The inspections of
micro-switch should be done every three months.
(3) Check the connecting lines of primary circuit and make sure good insulation and
connecting tightness of cables of the battery, controller and motor. Check the cables every
three months.
(4) Check the spring of foot pedal or levers, make sure the usual deformation and
smoothly resiling of spring. Do the inspections every three months.
(5) Check if the contactor terminal is working freely and not felted. Do the inspections
every three months.
Notice:
The controller neednt be repaired by users, so dont open it for it may be damaged
and lose guarantee. Make the controller clean and dry, inspect and clear the diagnosis
13
history documents periodically. Never start the electric control of incorrectly-installing

vehicles.
Only trained people can do periodic maintenance and replace the damage parts with
genuine parts of controller. Use the genuine parts produced by our company for ensuring
the quality.
During inspection, if there is status that may bring damage or cause dangerous, inform
the agent immediately, they will make a decision of the operating security.
2.6.4 Particular notice
(1) As a special vehicle, electric forklift trucks need professional maintenance and
authorized persons driving to suit for the working environment, or errors will be shown in
electric system (including meter).
(2) As the power of the vehicle, battery is different from traditional energy; its actual
capacity is related to working state and aging, different from rated capacity. According to
the common performance, when capacity drops to 20% (one cell), charge the battery to
prolong the life of battery.
(3) Using PC machine or hand-hold device connecting with control device, the users
can enter into software setting interface with powerful functions within certain limits. You
can measure and know the working condition of truck more intuitively, for example as
follows: working current and rotating speed of drive motor; working current, rotating speed,
working hours and trouble list of lift motor, and other system parameters.
2.7 Caution plates

The caution plates attached on the vehicle indicates the operating method and
instructions. Before driving it, please be sure to read them thoroughly. If the caution plate
drops, stick it again. When maintaining, check if the caution plate is complete and the
writing is legible, if necessary, please replace them.
(1) Safety mark
People are forbidden to stand on or down the fork.
14
(2) General information when operating
(3) Nameplate of forklift truck
(4) Lubrication system
(5) Capacity chart
15
(6) Inspections before starting
(7) Add hydraulic oil
(8) Sling decal
(9) Sling point indication
(10) Forbid entering into the rear space of the mast
16
(11) Hand caution decal
(12) Forbid conveying person
(13) Routine battery use
(14) Routine battery maintenance
(15) Faulty starting decal (electric forklift truck witch DC motor)
(16) Overturn caution decal
17
. Construction, principle, adjustment and maintenance of

forklift trucks
1. Drive system
1.1 General description
The drive system consists of general transmission system and partial brake system.
With the front wheel duplex motor driving construction, the right and left front wheel
separately contain drive axle, transmission case, brake unit and drive motor, which
improves the working efficiency. The reducer and the brake unit assembled in the drive
axle housing forms a unit.
The travel speed of the truck is increased with the speed of traveling motor, while the
travel direction changes with the rotation direction of traveling motor. The sensor
assembled on the rear wheel sends the information to the controller which controls the
driving motor on the front wheels, with the different information accepted, the driving motor
transfers the different rotation, then the truck can be turned. The steering of the front wheel
is come out by the electrical differential, which instead of the differential composed of bevel
gear. With the system, the efficiency can be improved and the noise when the bevel motor
drives can be eliminated.
1.1.1 Reduction box
The reduction box consists of case housing, reduction device, brake friction device,
case cover and wheel axle. The outer housing and case cover are of cast construction. The
reducer device and brake friction device are assembled in the case body which is
combined of reducer outer housing and case cover. The power is transmitted to the wheel
axle through the transmission, drawing the rotation of front wheel. The reducer is fixed on
the joint plate of frame with 7 bolts. See the construction in Fig.1-1.
The parts of the drawing:
1.Wheel axle
6.Tappered roller
bearing
2.Bolt,drive axle
7.Housing,
reduction box
3.Sleeve
4.Axle ring
5.MLON-ring
8.Drain plug
9.Socket head plug
10.Socket head plug
11.Column pin
12.Retainer ring
13.Spacer
14.Spacer
15.Inner ring
16.Fixed seat
17.Screw
18.Internal gear
19.Planet bracket
20.Nut
21.Outer cycloid gear 22.Planet gear
23.Needle bearing 24.Outer spring
25.Outer spring
26.Big bevel gear
27.Pin
28.Inner spring
29.Bearing
30.Spring
31.Mini bevel gear
32.Pin
33.Case cover
34.Socket head bolt
35.Ball bearing
36.Input shaft
37.O-seal
38.Cycloid gear
39.Tapered pin
40.Spring
41.Washer
42.Pin
43.Washer
44.Brake friction piece
45.Spring gasket
46.Friction piece
47.Disk
48.Disk
49.Sealed gasket
50.Piston
51.Seal ring
52.Seal ring
53.Case cover
54.Socket head bolt
55.Socket head spring
56.Plug
57.Pin
58.Seal ring
59.Brake joint
60.Needle pin
61.Drain screw
62.Spring pin
63.Column pin
64.Brake lever
18
Fig.1-1 Drive axle

19
1.1.2 Front wheel assy

The front wheel is made up of rim and solid tyre. The types of the tyre and rim of the
front wheel:
Tyre size: 187-8
Outer diameter Width = 457170 (mm)
Rim: 4.33R
1.2 Disassembly of drive system
Before disassembling the transmission case, disassemble the front wheel assy and
traction motor joint with it, then you can do maintenance and service on the parts of
transmission case.
1.2.1 Removal of wheel (Fig.1-2)
Drain the oil from the transmission case
before disassembling the wheel. Loosen the
wheel nuts and remove the drive wheel, then
loosen the 7 bolts fixing in the frame and remove
the transmission case joint with traction motor
from the frame.
Fig.1-2
1.2.2 Disassembly of traction motor (Fig.1-3)
Remove the three bolts for traction motor
(1M1050 and 2M1090, Pos.1 and 2).
NOTICE:
Take off the traction motor from the
transmission case cautiously.
In case of the removal of the traction from the
transmission case, there is a danger to damage the
sealing surface of the o-ring in the housing. If only
removing the motor, seal the released transmission
opening to avoid the dirt from entering into the
transmission case.
Fig.1-3
1.2.3 Disassembly and assembly of transmission case
20
The parts of transmission case should not be disassembled generally. If its necessary
to disassemble it, please contact with the sale department of our company.
1.3 Assembly of drive system
1.3.1 Assembly of traction motor
Before mounting, clean the mating surface between transmission case and traction
motor with such as loctite 706 or alcohol carefully and make the surface dry, then check the
surface for damage, if damaged, remove it with hone.
NOTICE: For the causticity of detergent, when cleaning with it, draw on the
protective gloves and goggles to avoid the detergent from spattering on the skin.
Forbid swallowing and inhaling and vapors. If it happens, call medical help
immediately.
The seal gaskets of the shaft joint with the
motor are a double cam seal gaskets and an O-ring,
assembling separately on the flange of the motor
and reduction box housing. There is a hole in the
motor flange for mounting the fixing ring of shaft.
The shaft of the motor is fastened along the shaft
direction while the flange of motor fastened along
the opposite direction (See it as Fig1-4). The flange
of the motor is joint on the reduction box with three
M10 screws (See it as Fig.1-5), which the length is
Fig.1-4
50mm, 90mm, 90mm, and the torque is recommended 50Nm.

NOTICE: After connecting with the motor, the reduction
box only can be moved along the shaft direction, while
the shaft of reduction box is upright with the motor shaft.
For that, sling the reduction box and assemble the
spline positioned at the inlet of reduction case aiming
the motor shaft. To joint it conveniently, suggesting put
three screws in the joint hole of the screw firstly, after
the reduction box is
assembled with the motor, exchange with the screws.
Fig.1-5
21
When assembling the motor, for avoiding the happening of the noise in the
future, dont make the gear of motor hit the driving gear in the transmission case.
1.3.2 Mounting the transmission case on the frame (Fig.1-6)

Check the surface of frame joint plate for damage
and irregularities, and the regularity of transmission
case surface is required not bigger than 0.1mm.
Fasten the transmission case to the frame with 7 M14
hexagon bolts with torque 135 Nm. See it as Fig1-6.
There are one inlet and one outlet separately below
the transmission case frame.
Fig.1-6
1.3.3 Assembly of wheels (Fig.1-7)
The wheel axle of transmission case is fit for assembly of plastic solid tyres and
cushion solid tyres.
a) Make the assembly surface on wheel axle and wheel clean, and check it for
damage.
b) The bore in the rim should be in line with the bolts of the wheel axle, then push the
wheel on, confirming the rim surface and the wheel axle interface coincidently.
c) Tighten the spring gasket, flat gasket and nut with the torque 140Nm.
1. Nut, hub
2. Washer
3. Wheel
4. Bolt, hub
5. Wheel shaft
6. Reduction box
7. Driving motor
Fig. 1-7
22
1.4 Replenishing with gear oil

When the gear oil has been used for 1000 hours or one year (the accurate time is
according to the first reached time), exhaust the gear oil in reduction box and replace with
appointed gear oil, and do the detailed operation as follows:
(a) Unscrew the drain plug (pos.1) with seal ring
(pos.3), exhaust the gear oil, remove the iron powder
on the drain plug, then retighten the drain plug, and
replace the seal ring if necessary.
(b) Unscrew the oil-fill plug (pos.2) with seal ring
(pos.4).
(c) Inject the gear oil in transmission case. When
adding oil, make sure that there is not air in the
transmission case which will come into bubble.
(d) The standard voltage of appointed adding oil
is 0.550.65 litre, measured with funnel.
(e) The gear oil type must be one of the following.
MOBIL ATF 200
ATF 210
ATF 220
SHELL DONAXTM
ATF DEXRON D-21666
DONAX TG PLUS D-22543
DONAX TG D-21126
ESSO TYPE SUFFIXA
ATF D-21065 ATF D-21611
ATF D-22079 SAE-80W/API
GL4/UTTO
Fig.1-8
(f) Tighten the oil-fill plug which is with seal ring,
with torque 22 Nm. See it as Fig1-8.
23
2. Brake system
The brake system consists of brake pedal, master cylinder and oil-lubricant brake. The
oil-immersed multi-frictional plate brake is assembled in reduction box, eliminating the
pollution, extending the life of brake unit and descending the maintenance cost.
2.1.1 Brake pedal
The brake pedal assembly is of sling structure (see the construction as Fig.2-1),
mounting on the meter bracket with bracket. The lever of master cylinder transfers the
pedal force to brake oil pressure.
Fig.2-1 Brake pedal
24
2.1.2 Master cylinder

The master cylinder contains valve support, check valve, return spring, primary cup,
piston and secondary cup, which are all kept in place with stop washer and stop wire. The
exterior of the cylinder is protected from dust by means of a rubber dust cover. The piston
is actuated through the push rod by operation of the brake pedal. As the brake pedal is
pressed, the push rod pushes the piston forwards. The brake fluid in the cylinder flows
back to the reserve tank through the return port until the primary cup blocks up the return
port. After the primary cup passed through the return port, the brake fluid in the cylinder is
pressurized and opens the check valve, flowing through the brake pipeline to the operating
cylinder. Thus each operating cylinder piston is forced outwards. This compresses or
impacts the disc brake to slow or stop the truck. Meanwhile, the cavity caused behind the
piston is filled with brake fluid led through the return port and inlet port. When the brake
pedal is released, the piston is forced back by the return spring. At the same time, the
brake fluid in each operation cylinder is pressurized by the return spring, returning into the
master cylinder through the check valve. With the piston in its original position, the brake
fluid in the master cylinder flows into the reserve tank through the return port. The brake
fluid in the brake pipelines and operating cylinders has a residual pressure proportioned to
the set pressure of the check valve, which makes each operating cylinder piston cup
securely seated to prevent oil leakage and eliminates a possibility of air locking when the
truck is sharply braked.
1. Link rod
2. Push rod
3. Dust cover
4. Snap ring
5. Secondary cup
6. Piston
7. Primary cup
8. Spring
9. Check valve
Fig.2-2 Master cylinder
25
2.1.3 Connecting the brake system and drive unit

There are two connectors in the joint of drive unit and brake system, one used for
connecting the traveling brake pipe while the other is used for the exhausting of traveling
brake system. See it as Fig2-3.
a) Connecting of traveling brake
Connect the brake pipe connector and brake pipe with the torque 12-16Nm.
b) Connecting of parking brake
Connect the brake cable connector and parking brake lever.
2.1.4 Exhaust of brake system (Fig.2-3)
Exhaust the air mixed in brake system after
assembling the brake system and replenishing the
brake fluid, and do it as follows:
a) Release the exhaust valve to the position
where the brake fluid can be flowed.
b) Press the brake pedal again and again, then
the pressure from brake fluid can exhaust the air
mixed in brake system.
c) When there is only brake fluid after
exhausting the air, press the brake pedal and tighten
the plug.
Fig.2-3
d) Release the brake pedal and check the braking, if not brake well, do the exhausting
again and again until braking well.
2.1.5 Parking brake device
The parking brake device consists of parking brake
unit and brake cable. The parking brake unit is of ratchet
wheel type. Handle the brake lever to make the brake
cable run. Make the brake lever in an appropriate position
by adjusting the stroke of the brake cable.
If you want to release the parking brake position,
press the button in the top of brake lever.
Fig.2-4 Parking brake device
NOTICE: When the hand brake is in initial position, make the drive wheel roll
freely.
26
2.1.6 Operation of brake system

After assembling and debugging the traveling brake and parking brake, press the
brake pedal, the normal traveling brake will be came out. Put the parking brake lever on the
left side of meter bracket, the brake cable and the disk brake unit in the drive unit is
engaged. Pull down the parking brake lever, then the parking brake can be come out.
2.2 Maintenance and adjustment of brake system

2.2.1 Inspection and maintenance of brake system
a) Parking brake performance (Daily inspection)
Check if the parking brake is performed correctly, and then check if the inching switch
can cut off the circuit when pulling down the parking brake lever.
NOTE: After working for 3000 hours, confirm that the brake stroke of the piston
is not over 3.8mm, if not, replace the brake disk.
b) Traveling brake performance (Daily inspection)
Check if the brake fluid in oil is enough and if the brake pedal can return to the original
position by the spring.
c) Brake fluid leakage inspection
Press the brake pedal, if not brake well, check the assembly and tightness
performance of traveling brake system. Mark on the brake oil port to check for the leakage.
d) Inspection of master cylinder
If traveling brake not well, firstly check if there is air in the master cylinder. If there is air,
exhaust it. Then check the cup in the master cylinder for damage, if damaged, replace it
with a new one.
e) Inspection of brake cable
If the two wheels cant be locked completely at the same time after pulling down the
hand brake, check the brake cable for abnormally running, for block performance, for
unsuitable cable clearance and for wrong lever turning angle. You can adjust the adjusting
bolts in the two ends if the angle is improper or there is bigger idle stroke of the lever.
2.2.2 Adjust the brake pedal
a) Shorten the push rod.
b) Adjust the brake pedal to the proper height with stopper bolt.
c) With the brake pedal pressed by the idle stroke, pull the rod out until its front end
27
comes into contact with the master cylinder piston.

d) Tighten the push rod locking nut.
2.2.3 Adjust the brake switch (Fig.2-5)
a) Loose the locking nut of the brake pedal after adjusting the height of brake pedal.
b) Pull out the plug, separate the lead.
c) Turn the switch, with the clearance A=1mm.
d) Make sure that the brake lamp is on when pressing the brake pedal.
Fig.2-5 Brake switch adjustment
28
3. Steering system
The steering system is of powered steering system with load sensing, consisting of
steering wheel, steering axle, load sensing steering unit, check valve, steering motor and
steering device. The steering axle is connected with the load sensing steering unit with
knuckle, then the steering column can be tilted forward and backward to the proper angle
(See it as Fig3.1). The steering device is assembled on the rear of the frame, with the gear
turning pushed by the steering motor, then the steering wheel can be turned to steering.
Main parameter of steering system

Model
CPDS15
Item
Model
Steering unit
Priority valve
Steering motor
CPDS18
Rear wheel steering powered

Type
Powered steering system with load sensing
Model
BZZ5-50
Type
Split-flow dual way type
Model
VLC-60
Flow/Distributary
60LPM
Flow pressure
8MPa
Type
Inner gear type
Model
BMR-125
Displacement
117.9
Rated pressure
7.0MPa
310mm
Radius of steering wheel

Steering tyre
166-8
Steering rim
4.33R
29
Fig3.1 Steering system
3.1.1 Hand wheel

Hand wheel is operated in normal way, that is to say,
when turning the hand wheel right, the truck will turn right.
When turning the hand wheel left, the truck will turn left. The
rear wheels of the forklift truck are steering wheels, which
make the back of the truck swing out when turning. The
turning method can be mastered easily through practice.
30
3.1.2 The principle of powered steering system with load sensing

When turning the steering wheel, LS pipe will send the pressure signal from the
throttle in the steering unit to the priority valve, with the pressure, the core of the check
valve will be balanced to confirm the flow from CF port. The steering circuit doesnt
influence the other working circuits. Main displacement will firstly confirm the realization of
steering circuit, steering circuit pressure and displacement.
Fig3.2 Principle of powered steering system with load sensing
31
3.1.3 Steering device

The steering device (Fig.3-3) consists of gear group, steering motor, steering axle
body and steering wheel, etc. Driven by the gear motor hydraulic oil, the gear group makes
the steering wheel turn, which drives steering axle body turning. The wheel is assembled in
the rear wheel hub with wheel rim, while the rear wheel hub is assembled in the steering
axle body with two tapered roller bearing. In the inner of the bearing, there is oil seal, which
makes the lubrication grease hold in the wheel hub and steering wheel axle chamber.
The steering motor is of a cycloid gear type hydraulic motor (See it as Fig3-4), it is
tandem with powered steering unit, drives the gear group, then the steering wheel will be
turned.
When the steering wheel is in middle position, set the steering angle in electric control
0 degree, readjust the resistance value in middle position.
Fig.3-3 Steering device
32
Fig.3-4 Steering motor

3.2 Adjustment and maintenance
3.2.1 Rear wheel bearing pre-load adjustment
a) As shown in Fig3-5, fill up the chamber formed by wheel hubs, wheel hub bearings
and wheel hub covers with lubrication grease. Coat the lips of the oil seals with lubrication
grease.
b) Press the hub bearing into the hub and fit the hub on the wheel shaft.
c) Fit a flat washer and tighten a castle nut with a torque of 206-235Nm (21-24kgm)
and loosen it, and then tighten it again with a torque of 9.8 Nm (1kgm).
d) To ensure firm installation of the hub, slightly knock at it with a wooden hammer and
in the meantime, rotate the hub for 3-4 turns.
e) Tighten the castle nut and align one of the notches with a cotter pin hole drilled in
the steering knuckle.
f) Again slightly knock at the hub with a wooden hammer and in this time, rotate the
hub manually for 3-4 turns to ensure its smooth rotation with a specified torque of 2.94-7.8
Nm (0.30.8 kg.m).
g) If the torque value necessary to rotate the hub is more than the specified one above
mentioned, screw out the castle nut for 1/6 turn and measure the torque value.
h) When the torque value measured is up to the specified one, lock the castle nut with
a cotter pin.
33
Fig.3-5 Pre-load adjustment

3.2.2 Inspection after reassembling the steering system
a) Turn the steering wheel left and right, inspect whether the steering power is smooth.
b) Inspect whether the connection of hydraulic pipeline is correct and whether the left
and right steering is opposite.
c) Lift up the rear wheels and slowly turn the steering wheel left and right several times
to exhaust the air from the hydraulic pipeline and the steering cylinder.
3.2.3 Steering system troubleshooting

Problem
Analyses of trouble
Remedies
Fail to turn
hand-wheel
Pump damaged or breaking down.

Hose or joint damaged or pipeline blocked.
The pressure of the relief valve is too low.
Air in steering oil circuit.
Steering unit fail to recover due to spring
piece damaged or elasticity insufficient.
Replace.
Clean or replace.
Adjust the pressure.
Exhaust air.
Replace spring
piece.
Inspect the seal of
the piston.
Difficult to turn
hand-wheel
Oil leakage in the steering motor.
Trucks snacking
Broken or deteriorated spring.
Replace.
or moving with oscillation
Too low oil level in the oil tank.
Refill oil.
Excessive noise
Suction pipeline or oil filter blocked.
Clean or replace.
Seals of guide sleeve, pipeline or joint
Oil leakage
Replace.
damaged.
Notice: The starting of hydraulic motor is controlled by the directional switch. Press
the accelerator pedal, the hydraulic motor will be started only when the directional switch is
in forward or backward position.
When exhausting, start the hydraulic motor, slightly turn the steering wheel left and
right (if anything unusual happens, turn off the power and resolve the problem), the turning
wheels will be turned, then the air in the steering system will be exhausted.
34
4. Electric system
Electric system mainly consists of battery group, traction motor, lift motor,
multifunctional integration controller system, control switch, liquid crystal instrument,
harness and lighting device, etc.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
Fig.4-1 Construction of electric system
35
Head lamp
Front combination lamp
Flash light
Inching relay
Meter assy
Start switch
Turning switch
Direction switch
Lamp switch
Hand brake
Main harness
Brake switch
Horn
Accelerator
Inching switch
Lift potentiometer
Socket assy
Battery assy
Controller assy
Rear working lamp
Rear tail lamp
Back-up buzzer
Fuse box
DC commutator
Steering potentiometer
Lift motor
Traction motor
Seat switch
Emergency switch
Fig.4-2 Principle of electric system
36
4.2 SME compact meter

4.2.1 General description
Three-wheel AC electric forklift truck adopts Italy SME newly LCD meter, displaying in
real-time on high definition LCD. The CAN wire of meter is connected with control main
board according to RS232 communication standard. The EYE software obtains allowable
landing and upgrade panel, with functions of detailed upgrade, diagnosis and adjustment.
The control circuit adopts SCM technology, sampling, displaying and controlling in
real-time. The intense and feeble circuit in the instrument adopts light-electricity separating
with control relay.
4.2.2 Outline and instructions of meter
Traveling speed (km/h)

Hand brake switch, lamp lights when pulling the hand brake
With safety seat switch open, meter indicates seat symbol, main
contactor cant be connected and truck cant travel until seat switch
closes.
Time meter (Odometer)
Turning angle, indicating the position of rear wheel
Maintenance time indication
Remind the users to maintain and service the forklift truck.
Slow-speed operating
With the lamp on, the traveling speed and lifting speed will be
reduced in slow-speed mode.
37
Traveling speed (Indicated from 0-9)
Overheated motor temperature warning

Battery level (indicated by 9 segments)
Display signals with alarm code 12 when battery is completely
discharged. Charge the battery when indicating on 1 segment.
Press E-S-H button, you can set operating mode for system.
(E-economic mode, S-midrange mode, H-high mode)
H-High mode: High acceleration, decelerate rate, max. grade ability,
suitable for loading large quantity goods in short time and climbing
abrupt slope, this mode wastes electricity, only used when
necessary.
S-Midrange mode: The parameter lower than High mode
E-Economic mode: The parameter has been optimized. Working on
this mode in general for saving electricity.
1. Start the key switch, press ENTER button for 3 seconds, enter
into adjust and diagnosis mode.
2. When operating, press for 3sec, enter into diagnose mode.
3. Quit when pressing ENTER under diagnosing mode, the enter
key is used for setting new parameter.
1. Reduce the parameter in adjusting mode when pressing this key.
2. The parameter can be reduced in adjusting mode.
3. Press the key for 1sec, indicating mileage or weight.
Note: The function of Up key is same to down key, enter, up and down key have
some functions not activated.
Four LED signals on the left of compact meter indicate when operating the relevant switch.
Alarm indication; red color LED
Lamps indication; green color LED
Steering switch on, steering signal activated; green color LED
Insufficient brake fluid; red color warning LED (optional)
38
4.2.3 Troubleshooting of alarm code
Alarm code
Alarm description
Alarm code
Alarm description
Max. battery voltage
Min. battery voltage
Pedal trimmer fault
Eeprom alarm
Pre-charge
Inverter
11
Capacitors
12
Low battery voltage
13
19
Over-heating motor
Motor current offset alarm
17
Main breaker
15
16
18
Watchdog timer alarm
37
Alarm on 5V encoder voltage
8
25
20
22
38
Power
Power inverter over-heating

Alarm on 12V output voltage
61
50
Pump motor commands
62
active on start
Motor blocking over-heating
65
63
74
75
80
Seat switch open on start
64
77
Encoder alarm
78
Wrong start
Motor thermal sensor alarm
Inverter temperature alarm
83
CRC fault alarm
84
Bank CRC restored
90
Steering sensor alarm
91
Brake pedal switch alarm
98
Capacitors pre-charge too slow
81
99
Capacitors pre-charge
timeout
39
4.2.4 Process and instruction of meter

(1) Turn on the key switch, some initial value mode will indicate for 3sec on the meter.
The mode helping operators judge the type of the forklift truck will indicate on the position
indicated speed, such as the four-wheel forklift truck is represented by CO. The information
about speed, electric energy, turning angle, hand brake, seat switch, E/S/H selection and
working hours is indicated on the meter, which help confirm the working state.
(2) Alarm indication is on the first left line of the liquid crystal form, indicating three
working states when it lights up, as follows:
Normally operating (When the system key is on or off, the lamp lights up)
Meter is not connected to the controller (The lamp is on after this state remains for
3sec)
Meter is not working (lamp lights)
No alarm code and the alarm indication lights off when the truck works normally.
(3) Move the turning switch forward and backward, the left and right turning signals
flash. When turn on the headlamp, lamp indication lights up.
(4) Brake indication
Operating the hand brake, indication as [P] lights up, release the hand brake, the
signal turns off.
Note: When the electric quantity is below normal, that is to say the position of
the hand on the meter is down one form, please charge up the battery.
4.2.5 Working circumstance

(1) Elevation is lower than 1200 meters.
(2) Working temperature -25+40.
(3) Relative humidity is not larger than 95%.
4.2.6 Cautions
(1) Forbid wetting the meter. When washing the truck, dont let water into the meter, if
it happens, clean it with dry cloth.
(2) Dont pull the plug of the meter and harness for the connection.
(3) Forbid impacting or scratching the meter strongly.
(4) When the meter works abnormally, contact with our company for maintenance.
40
4.3 SME AC electric control assy

Three-wheel AC controller assy is composed of three power inverters which
separately drives traveling and lifting motor, main control box, DC contactor, control
aluminum sheet. Main control box is connected with power source module, separately
controlling three power modules.
4.3.2 Structure of controller
Connector, K1 control box
Main contactor
Logic control box
Power module
for right motor
Power module
for lifting motor
Power module
for left motor
NOTICE: The electric control device contains capacitance which is discharged by

procedure through hydraulic motor when cutting off the key switch, then cut off the main
contactor to turn off the circuit power. Before doing the service, maintenance and
inspection for the forklift, firstly cut off the key switch for one minute, then discharge the
capacitance completely by process control.
41
4.4 Distribution and setting of sensor

The electric forklift truck embodies many superior features, such as infinitely variable
lifting speed, steering speed adjuster and pedal setting, which can be adjusted and set in
real-time by EYE software. These functions have been initialized before delivery and
neednt to be changed except the conditions as follows:
1. After long-term operation, the loose parts will be indicated with alarm codes.
2. The damaged electronic components are indicated with alarm code, replace them.
3. When replacing or disassembling other parts, its necessary to reset the value after
disassembling steering, lifting potentiometers.
4.4.2 Steering potentiometer
1. Specification of steering potentiometer
Resistance limitation: 0K-5K
Steering angle: 0-360
Voltage: 12V
2. Adjustment
a) Install the potentiometer on truck body, make steering wheels on zero degree
(straight traveling direction), adjust potentiometer to make output resistance value be about
2.5 K, if there is deviation, the output resistance must be between 0 K and 5 K when
locating on 90, -90 position.
b) Connect PC machine with controller connector.
42
c) If electric potentiometer installs correctly, the output voltage value will be changed
with hand wheels turning.
d) Enter STEERING SENSOR CALIBRATION menu.
e) Select ANTICLOCK parameter, turn hand wheel left until minimum steering value
displays, save it.
f) Enter CLOCK menu.
g) Turn hand wheel right, until maximum steering value displays, save it.
h) Enter MIDDLE menu.
i) Turn the steering wheel left and right until zero value displays (straight traveling
direction), save it.
j) Quit the menu.
Do trial operation, check if the position of steering wheel and displaying angle of meter
is consistent (range over 0, 90, -90).
4.4.3 Lift potentiometer
1. Specification
Resistance limitation: 0K-5K
Effective straight travel: 90.5mm
Voltage: 12V
2. Adjustment
a) Install potentiometer on the first level lift of multi-way valve, make sure that the top
lever of potentiometer runs freely.
43

c) Enter LIFT CALIBRICATION menu.
d) Select MINIMUM parameter, the minimum value will be indicated in lift calibration
value frame, save it.
e) Enter MAXIMUM menu.
f) Operate lift lever, until the maximum potentiometer output value indicates and save
it.
g) Enter MIDDLE menu.
h) Operate lift lever, until indicating middle value between minimum value and
maximum value, save it.
i) Quit the menu.
4.5 AC microtron
4.5.1 Outline and port function
4.5.2 Sketch for connector and port
No.
Definition
Color
Switch output1
Yellow
Switch output2
Blue
Power positive input
Red
(12V+) input
Power negative
Black
(12V-)
Accelerator
signal output
Green
Accelerator signal: linear ranged from 0.38V0.42V to 3.9V4.1V

Switch signal: Non-polarity opening contact. Capacity: 2A/100V
44
4.5.3 Setting for accelerator

a) Install potentiometer on front backing plate, make sure the accelerator pedal on
initial state.
c) If accelerator connects correctly, the output voltage will change with the stroke of
the pedal.
d) Enter ACCELERATION PEDAL CALIBRATION menu.
e) Press the pedal slowly until START lamp lights, save it.
f) Select MINIMUM menu, press the pedal slowly until output value is larger than start
value, save it.
g) Select MAXIMUM menu, press the pedal slowly until the max output value occurs,
save it.
h) Quit the menu.
45
5. SME three-phase AC motor

The power system of three-wheel electric forklift truck is composed of two three-phase
AC drive motors (6.5kw) and one three-phase AC lifting motor (12kw). Its with function of
speed sensor, temperature sensor, simple construction, reliable performance, free of
maintenance. The three-phase AC motor is composed of stator, rotor, speed encoder and
temperature sensor.
Structure of AC motor
1. Front cover
2. Bearing
3. Temperature sensor
4. Support cap
5. Stator
6. Rotor
7. Rear cover
8. Gear sensor
9. Speed sensor
5.2 Operating environment

(1) Elevation is lower than 1200 meters.
(2) Air temperature ranges between -25 and +40.
(3) Relative humidity is 100%.
5.3 Daily inspection and maintenance
(1) Always keep clean and no water, oil pollution or dust in the motor.
(2) Check the bearing for heat or leakage.
(3) The load current of the motor cant be over rated current.
(4) If there is friction, scream or other noise, stop working at once, after removing the
failure, the motor will keep on working.
46
6. Battery and charger

6.1 Structure of battery
Battery is composed of lower pole plate, negative plate, clapboard, battery groove cap
and electrolyte.
Fig.6-1 Structure of battery
6.2 Specification of battery

Model
DA505
Capacity
505Ah/5h
Voltage
48V
Density of electrolyte
1.280 g/cm3
Unit quantity
24
Max. weight
920kg
Min. weight
850kg
Charging pressure
48V
6.3 Usage and maintenance of battery

The correct using and daily maintenance is very important for the performance and
useful life of lead-acid battery. Operators must maintain and service the battery according
to the manual and realities, fill in the record card of charging. The card can be copied as
the daily inspection record, referred to the attached list at the back of the manual.
47
6.3.1 Information about battery operation

(1) Before using the new battery, clean the surface and check for the damage. Smear
butter or vaseline on the connectors to retard corrosion.
(2) The battery is assembled on the truck for balance weight, if its lower than the min.
weight, the load capacity will be affected. When assembling the battery on the truck, fasten
it with pin. The pin must be assembled after lifting and replacing the battery. The stability of
the truck will be affected with no fixed pin.
(3) The first charge before using new battery is initial charge, after that, the current of
common charging must keep the specified value, and input capacity is 130%-150% of
output capacity, the battery must charge for about 12 hours.
(4) When operating the battery, avoid over-discharging (mean the voltage of single
battery is lower than 1.80V) and over-charging, for it will effect the usual life and
performance of battery.
(5) When charging, open the cap for pouring liquid. After finishing charging, close the
cap. Keep the vent clear, for prevent exploding and damage of battery.
(6) After using the battery, charge it in time. If not charging in time, undercharge
usually, standing idle without charging for long time or over discharging, the pole plates of
the battery will be sulfatization, which effect a decline in performance of the battery or
cause failure if seriously.
(7) There is oxygen-hydrogen separated out when charging, its necessary to keep
good ventilation condition and avoid burning to keep off the explosion.
(8) During using and charging, the level of the electrolyte will decrease and the density
will increase. Usually add distilled water to keep normal capacity and density of electrolyte.
Notice: Electrolyte cant be added directly.
(9) Keep the surface of the battery clean, maintain and service the pole terminals,
bolts and connectors, loose connections or poor contact must be removed in time.
(10) During using the battery, if the voltage of the single battery is uneven or the
battery is not often used, a balanced charging (an amount over charge) every month is
necessary.
6.3.2 Compound electrolyte

(1) The electrolyte of battery must be compounded with sulphuric acid and distilled
48
water or deionizer water according to GB4554 standard. The density of electrolyte is

1.280-1.290g/cm3 (25).
Temperature conversion of density
The density of electrolyte is changed with temperature, the relation is counted as
follow formula: D25=D t0.0007
D25The density of electrolyte (g/cm3) at standard temperature (25)
D tThe real density (g/cm3) when the temperature is t
0.0007Exchange factor of temperature
tThe temperature of electrolyte when measuring density
(2) Compound the electrolyte with ceramics cylinder which is anti-acid, anti-heat,
without iron, or other anti-acid containers. When compounding the electrolyte, first put
measured distilled water or deionizer water in clean container, then put measured thick
sulphuric acid into water, at last mix them with vitriol stick.
Note: Dont put water into thick sulphuric acid against spattering and causing
injury.
6.3.3 Perfusing electrolyte

(1) After assembling the battery, twist pore plug and pour the electrolyte cooled down
to 30 into the battery, which will be absorbed by pole plates, add electrolyte to 15-20mm
upper the plate in time.
(2) After perfusing the electrolyte, the temperature of the battery will raise. Charge the
battery after the fluid cooling down to 35 about 4-8 hours later.
Note: Normally, the electrolyte in the battery has been compounded, so its not
necessary to add again. The electrolyte only can be added and compounded
according to the need when the professional repairs the battery.
6.3.4 Measure density of electrolyte

The density of electrolyte is changed with the temperature. When measuring the
density of electrolyte, put the sucker of the densimeter into the electrolyte vertically,
extruding the rubber tube with finger, then the electrolyte will be absorbed into the glass
tube, at last, the buoy of densimeter will float. Read the number of densimeter.
Note: The densimeter must be floated vertically, not lean to the glass tube.
49
6.3.5 Adding distilled water

(1) Get a certain amount of distilled water with a graduated container.
(2) Open all pouring caps of battery units.
(3) Absorb distilled water with ball type injector to charge the battery. When electrolyte
is over 15-20mm upper the plate, stop charging.
(4) After charging, tighten the pouring cap.
(5) Clean the surface of battery unit with a wet cloth.
Note:
(1) Wear eyes-protect glasses, rubber overshoes and rubber gloves.
(2) When adding the distilled water, never exceed the appointed amount. Adding
too much will lead the leakage of electrolyte, then the truck will be damaged when
charging or discharging.
(3) When adding too much, draw out water with ball type injector.
6.3.6 Charge the battery

(1) Precaution when charging
a. Each time after the battery is discharged, it should be charged in time. Dont place
50
the discharged battery more than a day. If it is left idle for long time without charging,
sulphatized pole plates will make the battery reduce performance.
b. When the forklift truck is seldom used, it is necessary to charge the battery full
before laying aside and then charge it once a month.
c. Measure the density when the discharging quantity is thought very weak, when the
density is below 1.160, it is necessary to charge the battery.
d. Balanced charging is necessary when the density difference is over 0.020, usually
give the battery a balanced charging every two months.
e. When the time of balanced charging is too more, that is over charging, batterys life
will be shorten.
f. If the temperature of electrolyte is above 55 before charging, it is necessary to
leave the battery idle for a period of time, not until the temperature come down can it be
charged.
g. Overcharging or over discharging could make the temperature of electrolyte go up.
When charging the battery, open the battery cover to radiate heat and ventilate.
(2) Characteristics of full charging battery
a. The battery voltage is about 52V (1-2.5t forklift truck with 24 groups batteries,), or
86.8V (3t forklift truck with 40 groups batteries).
b. The density of electrolyte is about 1.280g/cm3.
6.3.7 Storage of battery

(1) Store the battery in dry, clean, proper ventilation warehouse. (540)
(2) Let the battery far away from the direct sunshine, insolating and drenching, and the
heat source over 2 meters.
(3) Avoid the battery being upside-down, tailed-flat, knocked or pressed.
(4) Far from any poisonous or mordant things. Forbid any metals and foreign matters
dropping into the battery.
(5) Dont store the battery with electrolyte. Under special conditions, charge the
battery and adjust the fluid level and density of electrolyte. In the process of storage,
charge the battery according to the common way every month.
51
6.3.8 Handle waste battery

Waste battery should be handled properly in line with relevant laws and
regulations.
6.4 Troubleshooting
There are lots of reasons for the troubles, besides production quality or transportation
and storage, unsuitable maintenance will lead to many troubles. After the failure launch, its
necessary to analyze and take effective measures to remedy as soon as possible. The
features, reasons and troubleshooting of the common troubles are as follow:
Feature
Cause
Remedy
Balanced charging,
Not enough charge.
improve the operating

way.
1. Rated capacity not being
Density of electrolyte is too
Adjust the density of
reached or not enough.
low.
electrolyte.
The connecting line isnt
Unblock the outer

connection line and
clear, too high resistance.

reduce the resistance.
Capacity drops
Charging repeatedly to
Pole plates are sulphated
exhaust the condition of

sulphating.
2. Capacity drops gradually.
There is harmful matter in
Check electrolyte,
electrolyte.
replace it if necessary.
The battery is localized

Check and remove.
short circuit.
The inner or outer short
3. Capacity drops suddenly.
Check and remove.

circuit of battery
1. The voltage is too high

The pole plates are
Exhaust the condition of
sulphated
sulphating.
when charging, drops quickly

Voltage is
when discharging.
abnormal
2. Opening voltage reduces
Check signal voltage and

Opposite pole, short circuit.
markedly.
exhaust it.
52
Feature
Cause
Remedy
1. No gas or little during the
Low charging current or
Adjust charging current
end stage of charging.
charging not enough.
and go on charging
Short circuit of the inner

2. No gas after charging.
Repair the short circuit

battery.
Abnormally
3. Giving off too early with
giving off gas
large quantity gas when

Pole plates are sulphated.
sulphating
charging.
No laying after charging, or
Discharge or replace
there is impurity in
electrolyte after laying for
electrolyte.
1 hour.
4. Give off gas on the process

of laying or charging.
1. When charging normally,
Adjust the charging

Too large current or short
the temperature raises

Temperature
current or exhaust the

circuit when charging.
abnormally.
short circuit.
of electrolyte is
high
2. Some batteries temperature

Pole plates are sulphated.
is higher than others.
sulphating.

1. Density rises less or stays.
Pole plates are sulphated

sulphating
Color and
Many impurities are in

2. After charging, the density
density of
Quick self-discharging.
electrolyte, replace
drops heavily when storage.

electrolyte is
abnormal
electrolyte.
3. The color and smell is
Electrolyte is not pure,
Replace electrolyte and
active matter gives away.
clean the inner part
abnormal, and with turbid

sediment.
6.5 Charger
Charger consists of controller, power block and transformer. It adopts intelligent closed
cycle control, it can display the status of charge and fault, and can measure the battery
automatically. Its with dynamic tracking, closed cycle controlling, making the battery keep
in the critical state of optimal charging electrochemical reaction.
53
6.5.1 Charger panel
(1) When connect to power and turn switch, Power indication lamp lights.
(2) When the battery quantity is full, Full indication lamp lights.
(3) When the battery needs balanced charging, press Balance button and connect
power, -JH-displays on the display screen , when pressing the button again, the charger
restores to normal.
6.5.2 Usage of the charger and charging method
(1) Daily charging
When the under voltage warning of the battery displays on the liquid crystal displayer,
please charge in time according to the following essentials:
(a) Park the truck at appointed place. Turn the key switch on OFF position and
connect the battery. When replace the battery, sling it from the truck as rules.
(b) Confirm the input voltage and frequency of the charger, select appropriate the
switch socket matched with the battery.
(c) The minimum quantity of electrolyte should be kept, the level of the electrolyte
must be higher than guide plate for 15-20mm, or be in the scale range ruled by vent plug.
(d) Correctly connect the plug of the battery with relevant charger.
(e) Turn on the switch, the charger displays systems version, the voltage of battery
and the maximum charging current of charging. The charger begins to give an automatic
test.
(f) After testing, the charger enters formal charging procedure, scroll displaying as
follows: voltage [ . U], current [ . A], charging time [H . ]
(indicating hourminute) and ampere-hours charged [AH].
54
(g) When the full indicator flashes, the battery capacity is full. The charger has entered
automatically floating state, at the same time, the floating current of the charger is 1-3A.
(h) After having charged, turn off the switch, disconnect the battery plug from the
charger.
(i) Before using the forklift truck, make sure the specific gravity of battery electrolyte
has achieved the value as follows:
Temperature of
Specific gravity of
Temperature of
Specific gravity of
electrolyte
electrolyte
electrolyte
electrolyte
1.294
25
1.280
15
1.287
35
1.273
(2) Balanced charging

After the battery fully discharging, measure the specific gravity when charged distilled
water, and that of all batteries, then converse the values (setting the temperature 25),
come out the difference. When the difference is over 0.02, and other performance ruled,
balanced charging is necessary. Charging equally according to these procedures:
After operating by the way the same with daily operating, press balance charging
function button, the balance indicator flushes and JH appears. When the battery is
fully charged, press the balance button to release. The charger returns to normal
condition.
Notice: If charged more frequently, it may lead overcharge and shorten the
useful life of battery.
55
7. Hydraulic system
The hydraulic system consists of pump, control valve, lift cylinder, tilt cylinder and
hydraulic pipes.
The hydraulic oil, supplied by the oil pump connecting with the motor, is distributed to
the oil cylinders by the control valve.
Model
Item
Type
Model
Main pump
Displacement
Drive
Type
Control valve Model
Adjusting pressure
Type
Inner diameter of cylinder
Lift cylinder
Outer diameter of piston rod
Stroke
Type
Inner diameter of cylinder
Tilt cylinder
Outer diameter of piston rod
Stroke
Oil tank
Capacity
CPDS15
CPDS18
Gear type
SG05A20L224C
20 ml/rev
Connect with motor
Plunger piston
MSV04
14.5 MPa
16 MPa
Single action piston type with cut off valve
45 mm
36 mm
1495 mm (lift height is 3000mm)
Dual action piston
63mm
36mm
85mm
24L
7.1.1 Oil pump

Oil pump is gear pump, the type is SG05A20L224C (Chinese brand).
The lift oil pump is driven by lift motor. The oil from pump is distributed into two classes
through priority valves. One is for steering unit and another is for control valve.
7.1.2 Control valve
The control valve is of two-spool, four-body type. Controlled by the control valve lever,
the hydraulic oil from oil pump distributes the high pressure oil to lift cylinder or tilt cylinder.
There are safety valve and self-lock valve in the control valve. Setting on the upper side of
control valve inlet, the safety valve can control the system pressure. Setting in the tilting
valve, the self-lock valve is used to prevent the serious results happening because of
miss-operating when the tilt cylinder has no pressure source. There is check valve
separately between the inlet port and lift valve inlet, between lift valve inlet and tilt valve
inlet. See Fig7-1.
56
Fig.7-1 Outline of control valve
(1) Spool valve operation (Take the tilt spool valve

for example)
(a) Neutral position (Fig7-2)
The high-pressure oil from lift pump returns to
the oil tank through the neutral position.
Fig7-2
(b) Pushing-in of spool valve (Fig7-3)
In this time, the spool is pushed in to close the
mid-passage. This causes the oil from the main
oil-inlet to push up the inlet check valve and to flow
into the port B. The return oil from the port A
flows through the low pressure passage to the tank
and the spool is restored to its neutral position by the
return spring.
Fig7-3
57
(c) Drawing-out of spool (Fig7-4)

With the mid-passage closed, the oil from the
main oil-inlet pushes up the check valve and flows
into the port A. The return oil from the port B
flows through the low-pressure passage to the tank.
The spool can be restored to its neutral position by
return spring.
Fig.7-4
(2) Relief valve operation
There is a relief valve between the HP port of
oil pump and low pressure passage LP. The oil
through lift valve C will act on the surface with
diameter A and B, then the check valve K and
relief lift valve D will fall on the valve seat. See
Fig7-5.
Fig.7-5
When the setting pressure of the HP passage

affects the spring of the guide valve, the check
valve E is being opened. The oil flows into low
pressure LP through the port. See Fig7-6.
Fig7-6
As the guide valve E is opened, the pressure
on the inside of the valve C decreases, valve E
and valve C both fall on the valve seat, the flow in
the back of relief valve D will be shut, then the
pressure on the inside will be decreased. See
Fig7-7.
Fig.7-7
58
As the imbalance pressure between the HP

passage and the inside of oil pump, the pressure
difference makes the valve D open, oil flows directly
into the low pressure circuit LP. See Fig.7-8.
Fig.7-8
(3) Action of tilt-lock valve
Tilt spool valve housing contains a tilt-lock valve. The tilt lock valve is extended to
prevent vibrations of the mast tilting from the negative pressure in the tilt cylinder and
also to avoid the danger for mishandling of the tilt valve spool. When the lift motor
stops running, the mast cant be tilted forward even pushing the tilt lever.
The flow of the oil when pulling the valve core out is referred to Fig.7-10. At this
time, the mast is in backward tilt position.
The following is the situation as pushing in the valve core. (Fig.7-9)
(a) The core valve is pushed in
(When the pump works)
The pressure oil from the main pump flows
through the port B to tilt cylinder, then effects on
,P. The oil will go to

the low oil passage through port ,A and ,B, at
the piston through the port
last go back to the oil tank.
Fig.7-9
(b) The core valve is pushed in
(When the pump stops)
When the pump stops, push the core valve in,
without the oil flowing into the oil cylinder
connector B, then the pressure from port
,P
will not be increased. The piston will not move while

the oil from oil cylinder connector A cant go back
to the oil tank, then the oil cylinder will stop working.
Fig.7-10
59
(4) Operation of the control valve

The control valve is operated with the valve levers. All valve levers are assembled
together with a shaft and the shaft is assembled on the front guard with the bracket. The
valve levers operate the control valve with the joints. See Fig. 7-11.
Fig. 7-11 Operation of the control valve
No.
Symbol
Name
No.
Lift
Symbol
Name
Fig.7-12 Symbol of the operation lever

60
Tilt
As you see in Fig.7-12, the mast lift up when you push the lift lever forward, the mast
fall down when you pull the lift lever backward. The mast tilt forward when you push the tilt
lever forward, the mast tilt backward when you pull the tilt lever backward.
(5) Setting pressure of the relief valve

The pressure of the relief valve has been set before delivery. Dont adjust the pressure
at will, for it will bring danger for system and safety. If the oil pressure is different with
standard value as the following form, according to the measure method specified in
JB/T3300, it can be adjusted by specified servicemen as follows:
(a) Screw out the measured hole plug from the inlet port of control valve and install the
oil-pressure gauge (20MPa) on it.
(b) Operate the tilt lever, measure the pressure when the stroke is to the bottom.
(c) When the oil pressure is different from the specified value, loosen the lock nut of
the surplus valve, adjust the adjusting screw left and right to achieve the specified value.
Turn the screw left when pressure is high, and turn right when it is low.
(d) After having adjusted, tighten up the lock nut.
Forklift truck
Main relief pressure
1.5t
1.8t
14.5MPa
16MPa
8MPa
8MPa
Steering unit pressure
Fig.7-13 Pressure adjusting of relief valve
61
7.1.3 Lift cylinder

The lift cylinder is of single-action piston type. It consists of primarily of cylinder body,
piston rod, piston and cylinder head. The bottom of the cylinder is connected with the
cylinder supporter of the outer mast by blots and pins, while its top (i.e. piston rod head) is
connected with the upper beam of the outer mast.
The piston, fastened to the piston rod with spring wire is fitted with oil seals and
bearings on its outer periphery.
There is a cut-off valve assembled on the bottom of the cylinder, for protecting the
cylinder if the high pressure hose is cranked suddenly when lifting the mast.
The bushing and oil seal is set on the cylinder head to support the piston rod and
prevent the entering of the dust.
Fig.7-14 Lift cylinder

62
1.
Upper beam
2.
Adjust shim
3.
Dust ring
4.
Oil seal
5.
Guide sleeve
6.
O-ring real
7.
Cylinder head
8.
Bushing
9.
Cylinder body
10.
Piston rod
11.
Piston
12.
Oil seal, piston
13.
Oil seal
14.
Ring
15.
Snap ring
16.
Cut-off valve
17.
Spring lock ring
18.
Cotter pin
19.
Lock nut
20.
Adjusting nut
21.
Joint
22.
Chain
23.
Chain wheel
At the bottom of the lift cylinder is a cut-off valve (see Fig.7-15), which operates when
the high-pressure hose bursts for any reason to prevent the load from dropping down
abruptly. The oil from the lift cylinder flows through small holes in the circumference of the
cut-off valve spool and produces a pressure difference between two chambers. As the
pressure difference is smaller than the spring force so that the cut-off valve spool wont
move. If the high-pressure hose bursts, the pressure difference will be enough to overcome
the spring force, causing the spool to move until the holes on the circumference on the
spool are blocked up and allowing only a small amount of oil to flow through the holes at
the spool end to let the forks descend at the low speed.
Fig.7-15 Performance of cut-off valve
63
7.1.4 Flow regulator valve

The flow regulator valve, located in the lift cylinder circuit to limit the descending speed
of loaded forks, has the construction as shown in Fig.7-16. When the lift spool is placed in
the lift position, the oil from the control valve flows through the oil chambers A and B, oil
holes C, D, E and F, and the chamber G to the lift cylinder without any regulation. When the
lift spool is placed in the down position, the oil flows in the reverse direction. When the oil
passes the orifice plate (5) and a pressure difference generates between the chambers A
and B, the pressure difference overcomes the force of the spring (2) and moves the valve
core (7) right, thus the oil flow is decreased by narrowing of the hole D and C, and reduces
the oil flow passing through the orifice plate (5).
1.
Joint
2.
Spring
3.
O-ring
4.
Snap ring
5.
Orifice plate
6.
Sleeve
7.
Valve core
8.
Ball valve
9.
Spring
10.
Valve body
Fig.7-16 Flow regulator valve
64
7.1.5 Tilt cylinder (Fig.7-17)

The tilt cylinder is of double-acting type. Each truck has two tilt cylinders which are
installed on two sides of the mast assembly with pin while their piston rod ends are
connected with the outer mast channels.
The tilt cylinder assembly consists primarily of piston, piston rod, cylinder body,
cylinder base, guide sleeve and seals. The piston, welded to the piston rod, is fitted with
two Yx-rings and one wear ring on its circumference. A bushing press-fitted to the inner
side of the guide sleeve supports the piston rod. The guide sleeve is fitted with dust seal,
snap ring, Yx-ring and O-ring to prevent oil leakage and keep dust off. Fitted with them, the
guide sleeve is screwed into the cylinder body.
When the tilt lever is pushed forward, the high-pressure oil enters into the cylinder
body from the cylinder tail, moving the piston forward and causing the mast assembly to tilt
forward until 5 degrees. When the tilt lever is pulled backward, high-pressure oil enters into
the cylinder body from the guided sleeve and moves the piston backward, tilting the mast
backward until 7 degrees.
Fig.7-17 Tilt cylinder
1. Ear ring
2. Dust ring
3. Snap ring
4. Yx-ring
5. O-ring
6. Guide sleeve
7. Bearing
8. O-ring
9. Piston rod
10. Cylinder body
11. Yx-sealing
13. Piston
14. Yx-sealing
65
12. Retainer ring
7.1.6 Oil tank

For the cleaning oil, there is an inlet filter and a return filter separately in the oil tank
and the tube.
7.1.7 Hydraulic oil circuit (See Fig.7-18)
Fig.7-18 Hydraulic oil circuit
Forklift truck
Main relief pressure
1.5t
1.8t
14.5MPa
16MPa
8MPa
8MPa
Steering unit pressure

66
7.2 Maintenance and adjustment of hydraulic system

7.2.1 Maintenance of gear pump
1. Pump body
2. Drive gear
3. Driven gear
4. Front cover
5. Rear cover
6. Lining plate
7. Seal ring
8. Snap ring
9. Oil seal
10. Snap ring
11. Bolt
12. Washer
Fig.7-19 Gear pump

1. Disassembly
Before disassembly the pump, make it clean and put the removed parts on the paper
or cloth. Dont damage the parts.
(a) Hold the pump in a vice by lightly clamping the flange section.
(b) Remove bolts
,11, pump cover , pump body (Fig.7-9).
(c) Remove lining plate , driving gear and driven gear .

(d) Remove seal ring and ring from the front and rear covers.
Caution: If the seal ring neednt to be replaced, dont remove it from the front
cover.
67
2. Inspection
The disassembled parts except rubber parts should be washed with gasoline.
(a) Pump body inspection (Fig.7-20)
If the scraping trace is up to 1/2 long of the inner periphery, it indicates that the bearing
and gear shaft are subject to excessive wear, replace the pump body.
(b) Lining plate inspection (Fig.7-21)
Inspect the contact surface of the lining plate. If the surface is worn or its thickness is
smaller than the specified value, replace the lining plate.
Fig.7-20
Fig.7-21
(c) Front and rear cover (Fig.7-22)

If the inner surface of bushings discolored over 150scope, replace.
(d) Inspect the driving gear and the driven gear. If they are worn, replace them.
(Fig.7-23)
(e) Replace seal rings, bushing seals, snap rings, oil seals and spring snap rings as
require.
Fig.7-22
Fig.7-23
68
3. Assembly
(a) Install a new seal ring and a new ring on the front cover of pump.
(b) Install the lining plate on the groove of the front cover, dont confuse the inlet oil
port and the outlet oil port.
(c) Install the driving gear and the driven gear on the front cover.
(d) Install the lining plate on the side of the gear, with groove aiming gear point, dont
confuse the inlet oil port and the outlet oil port. (Fig.7-24)
(e) Install a new seal ring and a new ring on the groove of the rear cover. (Fig.7-25)
(f) Install the rear cover on the pump body, dont confuse the inlet oil port and the outlet
oil port.
(g) Tighten up the connecting bolts with a specified torque of 9 to 10 kg.m after all.
Fig.7-24 Lining plate
Fig.7-25 Seal
NoticeThe maintenance data of oil pump parts may be different because of the
difference of manufacturers.
4. Trial run
After installing the gear pump in the truck, check it reassembled for specified
performance and do the trial run for it. If the pumps gears are seized or internal parts worn
excessively, you should renew the hydraulic oil and filters or clean them. The trial run
procedures are as follows:
(a) Install the gear pump in the truck. Then install a pressure gauge in pressure
inspection port of the control valve.
(b) Loose the adjustment screw of the relief valve and run the pump at 500 to 1000
rpm for ten minutes. The oil pressure should be lower than 10 kg/cm2.
(c) Increase the speed of the pump to 1500 to 2000 rpm for ten minutes.
69
(d) Without the change of the speed in step, increase the pressure to 20 to 30 kg/cm2
at a time and run the pump for five minutes. Then increase the pressure to 175 kg/cm 2.
Each circuit works for five minutes and then renews the return filter.
During the increase of the pressure, observe the change of oil temperature and pump
body surface temperature and working voice. If the oil temperature or pump body surface
temperature is excessively high, decrease the load to reduce the oil temperature, then go
on doing the test.
(e) After the trial run, measure the flow amount through lift speed with the pressure of
175 kg/cm2 of the relief valve.
7.2.2 Troubleshoot
If the hydraulic system has a fault, find out the possible cause according to the
following tables and repair it.
1. Control valve
Problem
Possible cause
Remedy
Lower oil pressure of the lifting oil
Spool is held up
Disassembly and clean
circuit
Oil hole is blocked
Vibrate and the oil pressure rising
Spool is held up
slowly
Exhaust not fully
Exhaust fully
The oil pressure of the steering oil
Spool is held up
circuit is more than the specified
Oil hole is blocked
value
Lower oil amount
Misadjusted relief valve
Adjust
Misadjusted relief valve
Adjust
Slide surface worn
Replace relief valve
O-ring seal aging or

broken down
Replace O-ring seal
Spring is worsen
Replace spring
Valve seat surface is

worsen
Valve seat surface is
worsen
Adjust or replace relief

valve
Correct valve seat
surface
Valve is held up
Noisy control valve

Oil leakage (outside)
Lower setting pressure
Oil leakage (inside)

Higher setting pressure
70
2. Gear pump
Problem
Possible cause
Remedy
Lower oil level of oil tank
Add oil up to specified level
Blocked pipe-line or oil filter
Clean or replace oil
Lining plate, seal ring, bushing

seals or snap ring broken down
Replace
Misadjusted surplus valve
Adjust the pressure of surplus

valve to specified value with
pressure gauge.
Air entering into the pump
Retighten loose connections for

suction pipe; Add oil into oil
tank; Replace oil seal
Worn suction pipe or

blocked oil filter
Check pipe or repair filter
Air entering in resulting from

loose suction connections
Retighten the connection
Too high oil stickiness
Use oil with proper stickiness
Air bubble in oil
Find out cause and correct

them
Replace
Less exhausting oil
Lower pressure of
gear pump
Noisy gear pump
Oil leakage in
pump
Oil seal or seal ring broken

down
Pump broken down
71
Replace
8. Mast system
The mast system is the type of lifting and descending vertically with rollers of the
two-stage. It consists of inner mast, outer mast and lift bracket.
The fork is fastened on the bracket upper beam groove with pin, the fork clearance
can be adjusted. The fork and bracket can be exchanged according to the international
standard.
Type
Rolling type, J-shaped inner mast, C-shaped outer mast

with free lift, 2-stage telescopic mast
Roller
112.3
Side roller
40
Chain wheel
4095113
Lifting chain
LH1223, 23 combination
Upper roller, outer mast
91.5
Mast lifting system
Hydraulic
Mast tilting device
Hydraulic
Fork clearance adjustment
Manual
8.1.1 Inner and outer masts (Fig.8-1)

The inner and outer masts are welded parts. The bottom of outer mast is connected
with the drive axle through supporting. At the outside middle of outer mast, there are tilt
cylinder connected with the frame. The mast assembly can be tilt forward and backward by
operating the tilt cylinder.
The outer mast is C-shaped cross section, fixed with main rollers and side rollers on
the upper part of it.
The inner mast is J-shaped cross section, fixed with main rollers and side rollers at the
bottom of it.
The maintenance of the rollers and the side rollers on the inner and outer masts
belong to exalted maintenance. Please be careful.
72
Fig.8-1 Inner and outer mast
1. Outer mast
7. Bolt
13. Adjust gasket
19. Snap ring
2. Pin
8. Bolt
14. Guide plate
20. Chain assy
3. Grease
9. Washer
15. Roller bearing
21. Short bolt
4. Mast bearing 10. Side roller bearing
16. Snap ring
22. Nut
5. Support cover 11. Side roller washer
17. Inner mast
23. Long bolt
6. Washer
18. Bearing, chain wheel
12. Adjust gasket
73
8.1.2 Carriage
The carriage moves up and down smoothly along the channel of the inner mast with
main rollers. The main rollers are mounted on the main roller shafts and blocked by snap
rings. The main roller shafts are welded on the carriage. The side rollers fitted on the
carriage with bolts. They roll along the flank plate of the inner mast and can be adjusted by
shims. Two fitted side rollers roll along the outside of the flank plate of the inner mast to
prevent the rolling clearance. The main rollers sustain the longitudinal loads and the side
rollers sustain the transverse loads.
1.
Carriage assy
2.
Load backrest
3.
Bolt
4.
Spring washer
5.
Side bearing
6.
Bushing
7.
Bolt
8.
Spring washer
9.
Shim
10. Shim
11. Fork assy
Fig.8-2 Carriage
8.1.3 Fork pin
The fork pin fastens the fork on the definite position. When adjusting the clearance of
the fork, pull the fork pin turn 1/4 circle, the fork clearance must be adjusted according to
the loaded goods.
8.1.4 Roller position (Fig.8.3)

There are two kinds of rollers, main roller and side roller. They are separately mounted
on the outer mast, inner mast and carriage. The main rollers sustain the loads from front
and rear direction while the side rollers sustain the side loads.
Notice: (a) Adjust the clearance of the side rollers to 0.5mm.
(b) Add grease on the surface of the main roller and the mast contact surface.
74
Fig.8-3 Roller position
8.2 Maintenance and adjustment of mast system

8.2.1 Adjustment of lift cylinder
When replace the lift cylinder, inner mast or outer mast, we shall readjust the stroke of
the lift cylinder as following.
(1) Install the piston rod in the upper beam of the inner mast without shims.
(2) Lift the mast slowly to the max. stroke of the cylinder and check the two cylinders
synchronize or not.
(3) Install shims between the top of the piston rod of the cylinder which stop first and
the upper beam of the inner mast (Fig.8-4). The shims are 0.2mm or 0.5mm thick.
(4) Adjust the tightness of lift chains.
The adjustment of lift cylinder also belongs to exalted maintenance. Please be careful.
Fig.8-4
75
8.2.2 Carriage adjustment

(1) Let the truck parking on the horizontal ground and make the mast vertical. See it as
Fig.8-5.
(2) Let the bottom of the fork contact with the ground. Adjust the adjusting nut for the
end nipple of the upper chain and make a distance A between the main roller and the
carriage. A:2034mm.
(3) Make the fork down to the ground and tilt backward fully. Adjust the adjusting nut
for the end nipple of the upper chain and make the two chains tightness be equal. (Fig.8-6)
Fig.8-5
Fig.8-6
8.2.3 Carriage rollers replace

(1) Fork a tray on the fork and let the truck parking on the horizontal ground. (Fig.8-7)
(2) Make the fork and the tray down to the ground.
(3) Disassemble the end nipple of the upper chain and take the chain down from the
sheave. (Fig.8-6)
(4) Lift the inner mast. (See Fig.8-7)
(5) Made the truck back-up if the carriage is fully separated from the outer mast. (See
Fig.8-7)
(6) Replace the main rollers.
Disassemble all the snap rings and take the main rollers down with a drawing tool
and remain the shims.
Ensure the new rollers are equal to the replaced ones. Install the new rollers inside
the carriage and block them with snap rings.
76
8.2.4 Mast rollers replace

(1) Use the same way as 8.2.3 to disassemble the carriage from the inner mast.
(2) Let the truck parking on the horizontal ground and wedge up the front wheels for
250 to 300mm.
(3) Apply the parking brake and wedge up the rear wheels.
(4) Disassemble the fitted bolts for the lift cylinder and the inner mast. Hang up the
inner mast without loosing the shims for the top of the piston rod carefully.
(5) Disassemble the connecting bolts for the lift cylinder and the bottom of the outer
mast. Disassemble the lift cylinders and the oil pipes between the two cylinders without
loosen the oil pipes joints.
(6) Put down the inner mast. Disassemble the main rollers under the bottom of the
inner mast.
(7) Replace the main rollers
Disassemble the upper main rollers with a drawing tool, dont loose the shims.
Install the new rollers and the shims disassembled before.
(8) Hang up the inner mast to let all the rollers go into the mast.
(9) Reassemble the lift cylinder and the carriage.
Fig.8-7
Fig.8-8
77
Appendix:
Charging record card of electric forklift truck
Model of truck
Identification No
Date of purchasing
Model of battery
Battery No
Date of first using
Date
Fluid level of
electrolyte
(Normal / lower)
Density of electrolyte (St)
Density of
3
electrolyte (g/cm )
(before charge
/after charge)
Charging
hours
(Begin/End)
Voltage
(V)
Charged
electricity
(Ah)
Distilled
water (ml)
It must be charged when the density of electrolyte is lower than 1.160g/cm .
S25=St+0.0007(t-25)
S25: The density when the temperature is 25
St: The density when the temperature is t (measured value)
t: The temperature of liquid (measured value)
Final voltage: about 52V(1-2.5t)
about 86.8V(3t)
Charged electricity: 130%-150% of battery ration.

Liquid level: Higher than the shield for 15-20mm
Abnormal condition:
Note:
Please copy and fill in this list strictly, it will provide basis for maintenance and
service of battery.
78
NOTE
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
79
EC DECLARATION OF CONFORMITY
MANUFACTURE
Name:
KION Baoli(Jiangsu) Forklift CO., LTD.
Address:
No.8 Xinzhou Road, Economic Development Zone,
Jingjiang ,Jiangsu, China
Post:
214500 ,Jiangsu, China
THE TECHNICAL DOCUMENTATION WAS COMPILED BY:
Wu,Yun-Cheng
Hoppengarten 19,Germany
40489 Duesseldorf,Germany
Name:
Address:
Post:
HEREBY DECLARES THAT THE PRODUCT DESCRIBED BELOW:

Description:
Industrial truck Counterbalanced Lift truck
Model:
Serial number:
Manufacturing year:
COMPLIES WITH THE PROVISIONS OF THE FOLLOWING EUROPEAN

DIRECTIVES:
2006/42/EC
Machinery Directive
2004/108/EC
EMC Directive
2006/95/EC
LVD Directive
COMPLIES WITH THE PROVISIONS OF THE FOLLOWING HARMONIZED

STANDARDS:
EN 1726-11998
Safety of industrial trucksSelf-propelled trucks up to and including 10000 kg

capacity and industrial tractors with a drawbar pull up to and including 20000 N
Annex I of Machinery Essential health and safety requirements relating to the design and
Directive 2006/42/EC construction of machinery
Done at:
On
Jingjiang ,Jiangsu, China Name of the signatory:

Title:
Signature:
80
/ChenBin
Director of Quality Assurance
KION Baoli (Jiangsu) Forklift Co., Ltd.
Service Hotline: 400-828-2789

Tel: +86 523 8461 6148
Fax: +86 523 8461 6126
P.C.: 214500
Add: No. 8 Xinzhou RoadEconomic Development ZoneJingjiangJiangsuChina
www.baoli-mh.com
* We reserve the right to make any changes or modifications of pictures and specifications in this
manual without giving previous notice and without incurring any obligation.
Edition: MC09-03:2010

Soubor 1 5 1 8 Cpds Obsluha 60

Uploaded by

Copyright:

Available Formats

Soubor 1 5 1 8 Cpds Obsluha 60

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Soubor 1 5 1 8 Cpds Obsluha 60

Uploaded by

Copyright:

Available Formats

OPERATION & SERVICE

Three-wheel Electric Forklift Truck

KION Baoli (Jiangsu) Forklift Co., Ltd.

. Construction, principle, adjustment and maintenance of forklift truck

5. SME three-phase AC motor 48

Charging record card of electric forklift truck 80

. External view and technical parameter

External view of three-wheel electric forklift truck

Power & Control

. Safety instruction, operation & maintenance of electric forklift truck

2.1 Shipping, loading, unloading and slinging

2.2 Storage of forklift truck

2.3 Precautions before operation.

2.4 Information of safety operation

The noise pressure level at

The vertical direction acceleration mean

the operators position

value from the seat to the operator

2.5 Periodic servicing and maintenance of electric forklift truck

Bearing, steering wheel

Pin, tilting cylinder

Add lubricating grease

To the oil level

DOT3 Compound brake fluid

3# Lithium base grease

2.6 Brief operation instruction

Function and working condition of operation device:

Park the truck.

Adjust lever, hand

Control the horn.

Lock, battery cover

Lock the battery cover

Foot brake pedal

Brake the truck.

Pull the lever backward fully.

Refer to Chapter of Electric System in this manual.

Operate tilt cylinder.

Tilt backward when pulling

2.6.2 Operating manual

history documents periodically. Never start the electric control of incorrectly-installing

2.7 Caution plates

(2) General information when operating

(3) Nameplate of forklift truck

(4) Lubrication system

(5) Capacity chart

(6) Inspections before starting

(7) Add hydraulic oil

(8) Sling decal

(9) Sling point indication

(10) Forbid entering into the rear space of the mast

(11) Hand caution decal

(12) Forbid conveying person

(13) Routine battery use

(14) Routine battery maintenance

(15) Faulty starting decal (electric forklift truck witch DC motor)

(16) Overturn caution decal

. Construction, principle, adjustment and maintenance of

9.Socket head plug