STRONG PARTNERS. TOUGH TRUCKS.

Four-wheel Electric Counterbalanced Lift Trucks

J2.00–3.20XM
2 000 – 3 200 kg
J2.00XM, J2.50XM, J3.00XM, J3.20XM

Specification data is based on VDI 2198

Equipment and weight:

Weights (line 2.1) are based on the following specifications:
Complete truck with 3 290 mm (J2.00-2.50XM) Vista 2-stage limited free lift mast, 3 100 mm (J3.00-3.20XM), 1 100 mm hook
type carriage with load backrest and 1 200 mm forks. Overhead guard and pneumatic shaped solid drive and steer tyres.
Forks:
J2.00-2.50XM: 100 x 40 x 900 to 1 200 mm long
J3.00-3.20XM: 100 x 45 x 900 to 1 200 mm long
Fork spacing:
Inside to inside, minimum: 30 mm
Outside to outside, maximum: 900 mm (J2.00-2.50XM) 875 mm (J3.00-3.20XM)
 NOTE:
Specification data is based on the
JXM ‘Plus’ option.
Specifications are affected by the condition
of the vehicle and how it is equipped, as well
as the nature and condition of the operating
area. If these specifications are critical, the
proposed application should be discussed
with your dealer. Specification data is based
on the JXM plus option.
‰ Nominal battery compartment length
¶ Bottom of forks
 Without load backrest
„ h6 subject to +/- 5 mm tolerance
{ Full suspension seat (FLS1500)
specified
z Add 28 mm with load backrest
‹ Stacking aisle width (lines 4.33 & 4.34)
is based on the V.D.I. standard
calculation as shown on illustration.
The British Industrial Truck Association
recommends the addition of 100 mm
to the total clearance (dimension a) for
extra operating margin at the rear of
the truck.
† Gradeability figures (lines 5.7 & 5.8)
are provided for comparison of
tractive performance, but are not
intended to endorse the operation of
the vehicle on the stated inclines.
Follow instructions in the operating
manual regarding operation on inclines.
™ With 'extended shift' on
‘ Variable
Tables key:

 Add 665 mm with load backrest

extension
U Add 685 mm with load backrest
extension
= Centre of gravity of unladen truck  Deduct 665 mm with load backrest
extension
Ast = Wa + x + l6 + a (see lines 4.33 & 4.34)
… Deduct 685 mm with load backrest
a = Minimum operating clearance extension
(V.D.I. standard = 200 mm BITA recommendation = 300 mm) „ Add 580 mm with load backrest
extension
l6 = Load length
Å Add 600 mm with load backrest
*Standard tread shown-see line 3.6 for optional tread extension
  Deduct 580 mm with load backrest
extension
S Deduct 600 mm with load backrest
extension
œ Wide tread required
 Alternative capacities available with
pneumatic tyres. Contact your lift
truck dealer.

Notice
Care must be exercised when handling
elevated loads. When the carriage
and/or load is elevated, truck stability
is reduced. It is important that mast tilt
in either direction be kept to a
minimum when loads are elevated.
Operators must be trained and adhere
Load centre to the instructions contained in the
Operating Manual.
Rated load (kg)

Distance from front of forks to centre of

gravity of load. Hyster products are subject to change without notice.
Lift trucks illustrated may feature optional equipment.
J3.20XM Rated load
J3.00XM Based on vertical masts up to
J2.50XM
J2.00XM 4 350 mm top of forks (J2.00-2.50XM) or Safety:
This truck conforms to the current EU requirements.
4 165 mm (J3.00-3.20XM).
Load centre (mm)
Mast and Capacity Information
Values shown are for standard equipment. When using non-standard equipment these values may change. Please contact your Hyster dealer for information.

The rated capacities shown are for masts in a vertical position on trucks equipped with standard or sideshift carriage and nominal length forks. Masts above the
maximum fork heights shown in the mast table are classified as high lift and, depending on the tyre/tread configuration may require reduced capacity, restricted back tilt
or wide tread.
Product Features

Application matched performance and battery shift life

■ Hyster ACX system offers extended shift life or extra AC performance options to suit each application.

■ AC technology on both traction and hydraulics for reliable, positive performance.

■ Brushless DC steering motor.

■ Compact dimensions and extraordinary manoeuvrability offer tight aisle widths.

Advanced ergonomic features to inspire productivity

■ Hydraulic control/seat choices.

„ Standard fully adjustable semi-suspension seat with integral armrest. With low effort, soft touch, manual
hydraulic levers.
„ Optional e-hydraulic seat with TouchPoint™ mini-levers provide ultimate fingertip precision control.
„ Optional e-hydraulic seat with TouchControl™ joystick. Especially suited to intensive applications where
hydraulic operation is frequent and accurate/delicate hydraulic control is required.
■ Convenient step and handgrip for ease of access.

■ Demand Sense Steering.

■ Monotrol® pedal (optional).

■ Clear view dash display with LCD indicators.

■ 4 pre-programmed performance modes.

„ Pin codes (optional) can be allocated to individual drivers allowing them access only to the performance
level suited to their ability and experience.
■ Battery discharge indicator with lift interrupt.

■ Full range of Vista masts. 2 stage limited free lift, 2 or 3 stage full free lift with hydraulic mast cushioning for
dependable handling of fragile loads.
Offering excellent visibility with smooth, low noise operation.

Dependability and low cost of operation

■ Extended battery shift life.

■ 1 000 hour service intervals on most major components*.

■ 100% brushless AC motors.

■ Oil immersed brakes.

„ Low brake pedal effort.

„ Minimum maintenance requirements.
„ Oil change interval is 2 000 hours.
„ Completely closed system, with brakes sealed inside the transaxle, make the truck ideally suited for
operating in wet, dirty or corrosive environments.
■ Auto regenerative braking.

■ On board diagnostics for early warning of maintenance requirements.

■ One piece frame, designed using FEA** technology, and robust steer axle design for proven durability.

* Subject to applications survey

**Finite Element Analysis
 Strong Partners, Tough Trucks,
for Demanding Operations Everywhere.

Hyster supplies a complete product range,

including Warehouse trucks, IC and Electric
Counterbalanced trucks, Container Handlers
and Reach Stackers.

Hyster is committed to being much more than a

lift truck supplier. Our aim is to offer a complete
partnership capable of responding to the full
spectrum of materials handling issues:

Whether you need professional consultancy on

your fleet management, fully qualified service
support, or reliable parts supply, you can
depend on Hyster. Our network of highly trained
dealers provides expert, responsive local
support.

They can offer cost-effective finance packages

and introduce effectively managed maintenance
programmes to ensure that you get the best
possible value. Our business is dealing with
your materials handling needs so you can focus
on the success of your business today and in
the future.

Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England.
Tel: +44 (0) 1252 810261 Fax: +44 (0) 1252 770702
Email: info@hyster.co.uk http://www.hyster.co.uk
A division of NACCO Materials Handling Limited.

Hyster®, ®
, Vista® and Monotrol® are registered trademarks of Hyster Company in the United States and in certain other countries.
08/07/TLC Printed in England TM
, FortensTM, Pacesetter VSMTM, DuraMatchTM, DuraMatch PlusTM, TouchPointTM, TouchControlTM, EZXchange & HSMTM are trademarks
TM

Form No. 901022/2

of Hyster Company in the United States and in certain other countries.