Pipe

FITTINGS
&
Flanges

Galvanised Malleable Fittings

MATERIALS Blackheart Malleable Iron castings.
DIMENSIONS generally to ASME B16.3 or JIS
B2301, depending on manufacturing source. JIS B2301
dimensions are generally considered to be corresponding
values to BS143 and BS1256, although some sizes are not
exact equivalents.

WORKING PRESSURES (except flanges)

Recommended maximum working pressures are 1379 kPa
for water and 1034 kPa for steam, air, gas and oil.
NOTE: Working pressures may also be limited by relevant
Pressure Piping Codes or Industry regulations.

UNEQUAL SIZES
THREADING is BSP pipe thread, to BS.21
(AS1722, Part 1).
The specification for BS 143 fittings is:
Taper External (Series R)Taper Internal (Series RC)
The specification for BS 1256 fittings is:
Taper External (Series R) Parallel Internal (Series RP)

When ordering Reducing Sockets, Nipples, Bushes

and Elbows, always state largest size first
e.g. 80 x 40 bush.
When ordering 3- or 4- way fittings, the sizing sequence
illustrated below should be adopted.

3
1

BS 1256

BS 143
3

2
4
20

Parallel Threaded Fitting:

Taper Threaded Pipe

Taper Threaded Fitting:

Taper Threaded Pipe

32

32
20

ALTERNATIVE THREADING to special order.

20

NPT (API linepipe threads) Taper Internal/Taper External

can be supplied for fittings to American specification
ANSI B16.3.

FINISH

= 32 x 20

= 32 x 20

NOTE: Locknuts and Plain Sockets without ribs, are

supplied with parallel threads.

32

32

Hot Dip Galvanised is the standard finish for stock.

20

TESTING
Fittings shall be subject to an internal hydraulic
pressure of 2068 kPa without showing any sign of
leakage or abnormality.

32
= 32 x 20

25

20

20
= 25 x 20 x 20

Galvanised Malleable Fittings

1

12

13

14

10

11

17

16

18

15

21

20

19

22

23

24

Nominal Range - Equal & Reducing Fittings (all sizes shown in mm)
Number

Item

Minimum Size

Maximum Size

Adaptor (not illustrated)

15

50

Backnut

150

Bend 90 M&F

150

Bend 90 F&F

100

Bend 45 M&F

15

50

Cap

150

Cross

10

100

Elbow 90 F&F

150

Elbow 90 M&F

100

Elbow 45 F&F

15

100

10

Elbow 45 M&F

15

50

11

Flange Undrilled

15

150

12

Flange Drilled

15

150

13

Hex Nipple

150

14

Plug Hollow.

150

15

Plug Solid

15

50

16

Socket

150

17

Tee

150

18

Union Flat Seat

150

19

Union Brass Seat F&F

100

20

Bush Reducing

10 x 6

150 x 125

21

Elbow Reducing F&F

15 x 8

50 x 40

22

Hex Nipple Reducing

10 x 8

100 x 80

23

Sockets Reducing

10 x 8

100 x 80

24

Tees Reducing

15 x 8

100 x 80

24

Tees Reducing Special

20 x 15

80 x 50

Black & Galvanised Steel Fittings

Screwed Steel Pipe fittings are designed for
use with Medium and Heavy pipes to
AS 1074. These BS EN 10241 fittings are the
recognised Standard for Medium Pressure
Screwed Pipework. Tubular items in this
range conform to AS 1074.

SPECIFICATION
BS EN 10241 Steel Threaded Pipe Fittings, Screwed
BSP Thread.
Australian Standard 1074 Steel Tubes and Tubulars
Threaded or suitable for Threading with Pipe Threads
of Whitworth Form.
Australian Standard 1650 Galvanised Coatings on
Ferrous Articles.

MATERIAL

PERMISSIBLE WORKING PRESSURES

TABLE 1 TAPER/PARALLEL THREAD
NON-GAS APPLICATIONS
Type of Service
Nominal Water & Inert Oil L.P.G.
Fuel Oil
Other Applications (Inc.
Bore of
Med. Hvy
Med &
Steam & Compressed Air)
Pipe
Hvy. Medium Press. Heavy Press. Medium Press. Heavy Press.
Temp.
Temp.
Temp.
Temp.
mm
kPa
kPa kPa kPa
C0
kPa
C0
kPa
C0
kPa
C0

*25
32
40
50
65
80
100
125
150

FINISH
Surface Condition
1. Black Steel: These fittings are generally degreased
and protected with a coating of light oil.
2. Zinc Protective Coating: Fittings may be supplied
zinc plated using the Electrolytic Zinc Coating
process on finished Black Fittings.
3. Hot Dip Zinc Galvanising: Galvanising of fittings
shall be performed before the thread cutting
operation, by means of the hot dip method.
4. Zinc Flake: Fittings may be supplied Zinc Flake
Coated. This process being performed on Finished
Black Fittings.

2410
2070
2070
1720
1720
1720
1380
1380
1030

140
140
140
140

1030
1030
1030
860
860
860
690

Threads for the screwed ends of fittings comply to the

appropriate requirements of AS 1722
Part 1: Sealing pipe threads and also ISO 7-1.
Female Ends: Normally supplied with parallel thread.
Male Ends: Normally supplied with taper threads.

1210
1030
1030
860
860
860
860

192
192
192
192
192
192
192

1210
1030
1030
860
860
860
690

100
100
100
100
100
100
100

1210
1030
1030
860
860
860
690

192
192
192
192
192
192
192

TABLE 2 TAPER/TAPER THREAD

NON-GAS APPLICATIONS
Type of Service
Nominal Water & Inert Oil L.P.G.
Fuel Oil
Other Applications (Inc.
Bore of
Med. Hvy
Med &
Steam & Compressed Air)
Pipe
Hvy. Medium Press. Heavy Press. Medium Press. Heavy Press.
Temp.
Temp.
Temp.
Temp.
kPa
C0
kPa
C0
kPa
C0
mm
kPa
kPa kPa kPa
C0

*25
32
40
50
65
80
100
125
150

3450
2760
2760
2410
2410
2070
1720
1720
1380

4140
3450
3450
3100
3100
2760
2070
2070
1720

340
340
340
340

1030
1030
1030
1030
1030
1030
1030

100
100
100
100
100
100
100

1210
1210
1210
1210
1210
1210
1030

192
192
192
192
192
192
192

1210
1210
1210
1210
1210
1210
1030

100
100
100
100
100
100
100

1210
1210
1210
1210
1210
1210
1210

*Up to and including

TABLE 3 TAPER/TAPER THREAD

GAS APPLICATIONS TO AS 1697
Nominal Bore of Pipe

THREADING

100
100
100
100
100
100
100

*Up to and including

Tubulars: These are manufactured from tubing made

in accordance with AS 1074 from steel with 0.06 max
sulphur and 0.06 max phosphorus.
Machined Fittings: These are manufactured to
dimensions in BS EN 10241:2000 and generally made
from Free Cutting Steel.

2070
1720
1720
1380
1380
1380
1030
1030
860

Med & Hvy.

mm

kPa

*25
32
40
50
65
80
100

1030
1030
1030
1030
1030
1030
1030

*Up to and including

192
192
192
192
192
192
192

Black & Galvanised Steel Fittings

4
2

12

11

15

14

13

10

17

16

Nominal Stock Ranges (all sizes shown in mm)

Number

Item

Minimum Size

Maximum Size

Barrel Nipple (Manufactured from heavy pipe)

80

90 Bend (M&M)

150

90 Bend (B/E) (Available black only)

150

45 Bend (M&M)

15

100

Reducing Bush

8x6

100 x 80

Elbow F&F

150

Cap

100

Elbow (M&F)

100

Hex Nipple (Equal)

100

10

Hex Nipple (Reducing)

8x6

100 x 80

11

Pipe Piece (Manufactured from medium pipe).

Dia. 15
Length 100

Dia. 50
Length 600 in 50mm
increments

12

Plug (Hexagon)

100

13

Socket (Equal) (To AS 1074)

150

14

Half Socket

150

15

Socket (Reducing)

8x6

150 x 100

16

Tee (Equal)

150

17

Tee (Reducing)

10 x 8

150 x 100

*Larger sizes available to order.

Black & Galvanised Steel Unions

BLACK STEEL UNIONS are used in a wide range of make-and-break joints
requiring periodic disconnection. Available in Steel-Steel, Steel-Bronze and
Bronze-Bronze seats in Female-Female and Male-Female types.
Black Steel Unions are all-purpose unions coated in black oxide to give
protection to the fitting until assembled to piping.
ZINC-COATED UNIONS are Electro Zinc Plated. This process gives a
complete coating both externally and internally which protects the Union
at thread and vital seat areas.

WORKING PRESSURES

RANGE

For standard screwed unions

8 to 25mm up to 21000 kPa Cold Working Pressure

6mm to 100mm nominal pipe size

32 to 100mm up to 14000 kPa Cold

Working Pressure

SEATINGS

For Steam Pressures and Temperatures

refer to SAA Boiler Code

THREADING
BSPTaper M and F Threads to AS 1722 Part 1.

Black

Zinc Coated

Steel-Steel. A general purpose combination recommended

where vibration is present, the most economically priced.
Steel-Bronze. A good combination where corrosion is
present and when periodic disconnection is required.
Bronze-Bronze. Should corrosion be a major factor, and
where consistent disconnection is required.

Stainless Steel Screwed Fittings - BSP

Range:
reducing),

Caps, Elbows 90, Elbows 45, Hex Nipples (equal and reducing), Plugs, Sockets (equal and

Material:

ASTM A351 Grade 316 (CF8M).

Thread:

BSP (Male taper, female parallel).

Pressure:

Nominal 1000 kPa working pressure, 2000 kPa test.

Tees (equal and reducing), Bushes, Unions, Barrel Nipples and Flanges.

Size Range: Generally 6-50mm, with larger sizes available to order.

RANGE

Caps, Elbows 90, Elbows 45, Hex Nipples (equal and reducing), Plugs, Sockets (equal and
reducing), Tees (equal and reducing), Bushes, Unions, Barrel Nipples and Flanges.

MATERIAL

ASTM A351 Grade 316 (CF8M).

THREAD

BSP (Male taper, female parallel).

PRESSURE

Nominal 1000 kPa working pressure, 2000 kPa test.

SIZE RANGE

Generally 6-50mm, with larger sizes available to order.

Sealants for Threaded Joints

Our comprehensive piping package includes a variety of accessory products for use with pipes and fittings. These
include flange bolts, as well as a range of sealing materials for threaded and flanged joints. For threaded joints the
most popular materials are shown below.

PTFE (TEFLON) TAPE

For high or low temperature sealing. Ideal for gas or liquid lines, it is one of the
cleanest and easiest ways to connect threaded pipes, fittings and valves.
A 50% overlap should be allowed when applying PTFE Tape.
A variety of tapes are available to suit specific needs including:
White General Purpose

YELLOW GAS TAPE

10m roll x 12, 19 or 25mm wide

(19mm and 25mm comply with BS4375)
10m roll x 12mm wide
AGA Approval No. 5582

PINK PLUMBERS TAPE

10m roll x 12mm wide

PLUMBERS HEMP
26m rolls, for use with soap or any jointing paste which is compatible with the line fluid.

PLUMBERS SOAP
Principally for water use, available in 500gm bars.

Flanges to Australian Standards

FLANGE TYPES
Specification AS 2129 covers plain face, raised face,
plain face with O-ring flanges in plate or forged as
specified. Types available are slip-on weld or blank
in plate and threaded, slip-on or weldneck in forged
material. Standard flanges are flat faced.

THREADING
Boss Flanges not exceeding 150mm may be supplied
threaded with a parallel or taper thread in accordance
with AS 1722.

MATERIAL
This section covers flanges made from steel forgings
and plates, but AS 2129 also applies to Stainless Steel.
Forged steel flanges conform to BS 10.

RANGE
FORGED
Table D (Galv) Threaded
Table D (Black) Slip-on weld
Table E (Black) Slip-on weld & Threaded
Table H (Black) Slip-on weld & Threaded

NOM SIZE
15-150mm
15-200mm
15-200mm
15-200mm

PLATE
Table D & E Slip-on weld
Table D & E Blank
Table H Slip-on weld
Table H Blank

NOM SIZE
15-600mm
15-600mm
15-600mm
15-600mm

TEMPERATURE-PRESSURE RATINGS FOR CARBON STEEL FLANGES

Flange
Table
-18 to
120
D
C
E
F
H
J
K
R
S
T

Pressure, kPa*
Temperature, 0C
325
350

-50 to
232
700

250

275

300

650

600

570

550

1 400
2 100
3 500
4 800
6 200
8 300
12 400
19 300

1 300
2 000
3 300
4 600
5 900
7 900
11 800
18 400

1 200
1 800
3 100
4 300
5 500
7 400
11 100
17 200

1 100
1 700
2 900
4 000
5 100
6 800
10 300
16 000

1 000
1 600
2 600
3 700
4 700
6 300
9 500
14 700

375

400

425

500

450

400

350

950
1 400
2 400
3 400
4 300
5 800
8 700
13 500

900
1 300
2 200
3 100
3 900
5 200
7 900
12 200

800
1 200
2 000
2 700
3 500
4 700
7 100
11 000

700
1 100
1 700
2 400
3 100
4 200
6 300
9 800

450

475

1 300
1 900
2 400
3 200
4 800
7 500

900
1 300
1 600
2 200
3 300
5 100

1 200

Max hydrostatic test

pressure
kPa
1 050
1 800
2 100
3 150
5 250
7 200
9 300
12 450
18 600
28 950

TEMPERATURE-PRESSURE RATINGS FOR ALLOY STEEL FLANGES

Flange
Table
-100 to 250
232
3 500 3 300
4 800 4 700
6 200 6 000
8 300 8 000
12 400 12 000
19 300 18 600

H
J
K
R
S
T

275

300

325

350

3 200
4 400
5 700
7 600
11 400
17 600

3 000
4 200
5 400
7 200
10 700
16 700

2 800
3 900
5 100
6 700
10 100
15 700

2 600
3 700
4 700
6 300
9 500
14 800

Pressure, kPa*
Temperature, 0C
375
400
2 500
3 500
4 400
5 900
8 900
13 800

2 300
3 200
4 100
5 500
8 300
12 800

*Intermediate values are to be obtained by linear interpolation.

Note: Carbon steel standard material stocked. Alloy steel available to special order.

10

425

450

475

482

500

525

2 100
3 000
3 800
5 100
7 600
11 900

2 000
2 700
3 500
4 700
7 000
10 900

1 800
2 500
3 200
4 300
6 400
9 900

1 700
2 400
3 100
4 100
6 200
9 700

1 200
1 700
2 200
3 000
4 400
6 900

500
700
940
1 300
1 900
3 000

Max hydrostatic test

pressure
kPa
5 250
7 200
9 300
12 450
18 600
28 950

Flanges to Australian Standards

DIAM.
RAISED FACE

1.6mm

DIMENSIONS
FOR LOOSE FLANGES

FLAT FACE

FLAT FACE

PLATE FLANGE
SLIP ON WELD

BLANK OR BLIND FLANGE

COPPER ALLOY
T.3 Plate or Boss or Blank
T.10 Plate or Boss
T.11 Blank

DIAM.
RAISED FACE

BOSS FLANGE SLIP ON WELD OR SCR. B.S.P.

NomiTable D
nal
Flange
Drilling
Size OD mm Thickness
Bolt No. of Dia. of
DN
T3 mm ** T6 Circle Bolts Bolts
Dia.
mm
mm
mm
15
95
6
5
67
4
M12
20
100
6
5
73
4
M12
25
115
8
5
83
4
M12
32
120
8
6
87
4
M12
40
135
10
6
98
4
M12
50
150
10
8
114
4
M16
65
165
11
8
127
4
M16
80
185
13
10
146
4
M16
100
215
16
10
178
4
M16
125
255
17
13
210
8
M16
150
280
17
13
235
8
M16
200
335
19
13
292
8
M16
250
405
19
16
356
8
M20
300
455
22
19
406
12
M20
350
525
25
22
470
12
M24
22
521
12
M24
400
580
25
450
640
29
25
584
12
M24
500
705
32
29
641
16
M24
600
825
35
32
756
16
M27
700
910

35
845
20
M27
750
995

41
927
20
M30
800 1060

41
984
20
M33
900
1175

48
1092
24
M33
1000 1255

51
1175
24
M33
1200 1490

60
1410
32
M33
Nominal
Size OD
DN mm
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
NOTES:

115
115
120
135
140
165
185
205
230
280
305
370
430
490
550
610
675
735
850

* (4)
(5)
(6)

WELD NECK FLANGE

T.6 Plate or Boss or Blank, or Weldneck (except for valves)

T.18 Plate or Blank or Weldneck (except for valves)

Table F
Flange
Drilling
OD mm
Thickness
Bolt No. of Dia. of
T10
T11 ** T6 Circle Bolts Bolts
Dia.
mm
mm mm mm
mm
95
8
8
10
67
4
M12
100
8
8
10
73
4
M12
120
10
10
10
87
4
M16
135
10
10
13
98
4
M16
140
11
11
13
105
4
M16
165
11
12
16
127
4
M16
185
13
13
16
146
8
M16
205
14
15
16
165
8
M16
230
17
17
19
191
8
M16
280
19
20
22
235
8
M20
305
22
23
22
260
12
M20
370
25
28
25
324
12
M20
430
25
32
29
381
12
M24
490
29
37
32
438
16
M24
550
32
42
35
495
16
M27
610
32
47
41
552
20
M27
675
35
52
44
610
20
M30
735
38
57
51
673
24
M30
850
41
68
57
781
24
M33
935

60
857
24
M33
1015

67
940
28
M33
1060

68
984
28
M33
1185

76
1105
32
M36
1275

83
1194
36
M36
1530

95
1441
40
M39

Table J
Flange
Drilling
Dia. of OD Thickness Dia. Bolt No. of Dia. of
Bolts mm * T6 mm R/F Circle Bolts Bolts
mm
mm Dia.
mm
mm
M16
115
16
57
83
4
M16
M16
115
16
57
83
4
M16
M16 120
19
64
87
4
M16
M16 135
19
76
98
4
M16
M16 140
22
83
105
4
M16
M16 165
25
102
127
4
M20
M16 185
25
114
146
8
M20
M16 205
32
127
165
8
M20
M16 230
35
152
191
8
M20
M20 280
38
178
235
8
M24
M20 305
38
210
260
12
M24
M20 370
41
260
324
12
M24
M24 430
48
311
381
12
M27
M24 490
51
362
438
16
M27
M27 550
57
419
495
16
M30
M27 610
64
483
552
20
M30
M30 675
70
533
610
20
M33
M30 735
79
597
673
24
M33
M33 850
92
699
781
24
M36

All dimensions are in millimetres (mm).

Only metric preferred sizes listed, except for DN 750 which is a
non-preferred size.
It is impractical to use flange thickness less than 12mm for
Steel Plate Flanges.

1.6mm

FORGED OR PLATE STEEL

Table E
Flange
Drilling
OD mm
Thickness
Bolt No. of Dia. of
T10
T11 ** T6 Circle Bolts Bolts
Dia.
mm
mm mm mm
mm
95
6
6
6
67
4
M12
100
6
6
6
73
4
M12
115
8
8
7
83
4
M12
120
8
8
8
87
4
M12
135
10
10
9
98
4
M12
150
10
10
10
114
4
M16
165
11
11
10
127
4
M16
185
13
13
11
146
4
M16
215
16
16
13
178
8
M16
255
17
17
14
210
8
M16
280
17
17
17
235
8
M20
335
19
20
19
292
8
M20
405
22
25
22
356
12
M20
455
25
28
25
406
12
M24
525
25
32
29
470
12
M24
580
25
36
32
521
12
M24
640
29
41
35
584
16
M24
705
32
46
38
641
16
M24
825
38

48
756
16
M30
910

51
845
20
M30
995

54
927
20
M33
1060

54
984
20
M33
1175

64
1092
24
M33
1255

67
1175
24
M36
1490

79
1410
32
M36

Table H
Flange
Drilling
Dia. Bolt No. of
Thickness
T10 T11 * T6 R/F Circle Bolts
Dia.
mm mm mm mm
mm
10
11
13
57
83
4
10
11
13
57
83
4
11
12
14
64
87
4
11
13
17
76
98
4
13
14
17
83
105
4
13
16
19
102
127
4
14
17
19
114
146
8
16
19
22
127
165
8
19
23
25
152
191
8
22
27
29
178
235
8
25
30
29
210
260
12
32
39
32
260
324
12
35
45
35
311
381
12
38
52
41
362
438
16
41
58
48
419
495
16
44
64
54
483
552
20
48
71
60
533
610
20
51
78
67
597
673
24
57
92
76
699
781
24

(1)
(2)

** (3)

FLAT FACE

1.6mm

DIAM.
RAISED FACE

Nominal
Size
DN

15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
750
800
900
1000
1200

Table R
Nominal
Flange
Drilling
OD Thickness Dia. Bolt No. of Dia. of Size
mm * T18 mm R/F Circle Bolts Bolts DN
mm Dia.
mm
mm
115
19
64
83
4
M16
15
115
19
64
83
4
M16
20
125
22
76
95
4
M16
25
135
22
76
98
4
M16
32
150
25
89
114
4
M20
40
165
25
102
127
8
M16
50
185
29
114
146
8
M20
65
205
32
127
165
8
M20
80
240
35
152
197
8
M24
100
280
41
178
235
12
M24
125
305
44
210
260
12
M24
150
370
51
260
324
12
M27
200
430
60
311
387
16
M27
250
510
70
362
457
16
M30
300
16
M33
350
585
79
419
527
640
89
483 584
20
M33
400
735
98
572
673
20
M36
450
805
105
622
730
20
M39
500

Thickness includes 1.6mm height for the Raised Face.

The Raised Face is non-preferred for Table H.
It is normal practice to supply Steel Flanges to Tables A, D, C, E, F
and H. Flat Faced.

IMPORTANT: For DN 65, DN 125 and DN 150 Flanges, the O.D. of pipe being used must be specified.

11

Bolting for Australian Flanges

I.S.O. METRIC HEXAGON STEEL BOLTS FOR USE WITH AS. 2129 FLANGES
Steel Hexagon Bolts and Nuts (XOX) are typically used within a temperature range of -50C to +300C.
Outside of this temperature range, Stud Bolts may be selected based on AS. 2528.
A quick reference chart for sizing bolts and nuts for a range of regularly used standard flanges is given below.

APPLICABLE TO PLATE AND FORGED STEEL LOOSE FLANGES ONLY

NOTE: Integral valve flanges quite often differ in thickness to equivalent loose flanges.

When integral flanges are involved due allowance should be made to bolt lengths.
Nominal
Flange Size
DN
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
750
800
900
1000
1200

Table D
No. Bolts Per
XOX
Flange
Bolt & Nut
dia. x lgth.
4
M12 X 40 mm*
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
8
M16 x 45 mm*
8
M16 x 45 mm*
8
M16 x 45 mm*
8
M20 x 55 mm*
12
M20 x 60 mm*
12
M24 x 75 mm*
12
M24 x 75 mm*
12
M24 x 80 mm*
16
M24 x 85 mm*
16
M27 x 100 mm*
20
M27 x 100 mm*
20
M30 x 120 mm*
20
M33 x 120 mm*
24
M33 x 140 mm*
24
M33 x 140 mm*
32
M33 x 160 mm*

Table E
No. Bolts Per
XOX
Flange
Bolt & Nut
dia. x lgth.
4
M12 X 40 mm*
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
8
M16 x 45 mm*
8
M16 x 50 mm*
8
M20 x 60 mm*
8
M20 x 60 mm*
12
M20 x 70 mm*
12
M24 x 80 mm*
12
M24 x 85 mm*
12
M24 x 100 mm*
16
M24 x 100 mm*
16
M24 x 110 mm*
16
M30 x 130 mm*
20
M30 x 140 mm*
20
M33 x 150 mm*
20
M33 x 150 mm*
24
M33 x 170 mm*
24
M36 x 180 mm*
32
M36 x 200 mm*

Table F
No. Bolts Per
XOX
Flange
Bolt & Nut
dia. x lgth.
4
M12 x 40 mm*
4
M12 x 40 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
4
M16 x 45 mm*
4
M16 x 50 mm*
8
M16 x 50 mm*
8
M16 x 50 mm*
8
M16 x 60 mm*
8
M20 x 70 mm*
12
M20 x 70 mm*
12
M20 x 75 mm*
12
M24 x 85 mm*
16
M24 x 100 mm*
16
M27 x 100 mm*
20
M27 x 120 mm*
20
M30 x 130 mm*
24
M30 x 140 mm*
24
M33 x 150 mm*
24
M33 x 160 mm*
28
M33 x 170 mm*
28
M33 x 180 mm*
32
M36 x 200 mm*
36
M36 x 220 mm*
40
M39 x 240 mm*

Table H
No. Bolts Per
XOX
Flange
Bolt & Nut
dia. x lgth.
4
M16 x 45 mm*
4
M16 x 45 mm*
4
M16 x 50 mm*
4
M16 x 55 mm*
4
M16 x 55 mm*
4
M16 x 60 mm*
8
M16 x 60 mm*
8
M16 x 65 mm*
8
M16 x 70 mm*
8
M20 x 80 mm*
12
M20 x 80 mm*
12
M20 x 90 mm*
12
M24 x 100 mm*
16
M24 x 110 mm*
16
M27 x 130 mm*
20
M27 x 140 mm*
20
M30 x 160 mm*
24
M30 x 170 mm*
24
M33 x 190 mm*

All dimensions are in millimetres (mm)

Inch series bolts interchangeable as follows:

Length

Bolt
Diam.

Flat faced joint illustrated

Bolt lengths listed apply to flat-faced or 1.6mm

raised face flanges with allowance for 1.6mm gasket
thickness.

* For approximate Stud Bolt Lengths take the XOX

Bolt Length and add the metric diameter in mm
rounded to the nearest 5mm increment up.
NOTE: This does not include length of point.

FOR
1/4
5/16
3/8
1/2
5/8
3/4

USE
M6
M8
M10
M12
M16
M20

FOR
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2

BOLT HOLE DIAMETERS

For bolts to M24, clearance hole 2mm larger.
Above M24, clearance hole 3mm larger.

XOXBOLTS & NUTS

XOX is the trade term used for H.R.H. commercial
steel bolts and nuts.
H.R.H. denotes Hexagon Head x Round Shank x
Hexagon Nut.

12

USE
M24
M27
M30
M33
M36
M39

Denso Corrosion Protection Systems

A Quality Commitment

Backed by over 80 years of practical experience in protecting metal

substrates against corrosion both above and below ground, and under
immersed conditions, Denso Long Life Anti-corrosion Systems have been
specifically formulated to enable cold application and do not require
elaborate surface preparation or equipment. Denso Systems readily
conform to suit most irregular contours and profiles.
Technical advice, specifications and problem solving together with on
site instructions in the correct application of the Denso Systems are all
part of the service offered by Denso.

SYSTEM SELECTION GUIDE

STRUCTURE

ENVIRONMENT

RECOMMENDED SYSTEM

TEMP.

Pipe lengths
Bends, Joints

Above ground
No mechanical impact or abrasion

Densyl KF ColourTape
(Self-extinguishes in 60 s)

(To 600C)

Pipe lengths
Bends, Joints

Above ground
Infrequent mechanical impact or
abrasion

Steelcoat 400 System

Penetrating Primer
Ultraseal tape
Acrylic Topcoat

(To 650C)

Pipe lengths
Bends, Joints

Above ground
Frequent mechanical impact
Heavy abrasion

Steelcoat 400 System

Penetrating Primer
Ultraseal tape
UrethaneTopcoat

(To 650C)

Pipe lengths
Bends, Joints

Below ground
Selected Backfill

Denso or Densyl Petrolatum System

MP Primer
Denso or Densyl Tape
PVC Self-Adhesive Tape

Denso
(To 550C)
Densyl
(To 750C)

Pipe lengths
Bends, Joints

Below ground
Original Backfill

Primer D
Denso Ultraflex 1500 or Densopol 60HT
Tape

(To 750C)

Pipe lengths
Bends, Joints

Below ground
Rock Backfill

Primer D
Denso Ultraflex 1500 or Densopol 60HT
Tape
Denso Rockmesh

(To 750C)

Valves, fittings and

other irregular profiles

Below ground

Denso or Densyl Petrolatum System

MP Primer
Denso Mastic or Densyl Supersoft Mastic
Denso or Densyl Tape
PVC Self-Adhesive Tape

Denso
(To 550C)
Densyl
(To 750C)

Valves, fittings and

other irregular profiles

Above ground
No mechanical impact or abrasion

Densyl Supersoft Mastic

Densyl KF ColourTape

(To 600C)

Valves, fittings and

other irregular profiles

Above ground
Infrequent mechanical impact or
abrasion

Steelcoat 400 System

Penetrating Primer
Densyl Supersoft Mastic
Ultraseal Tape
Acrylic Topcoat

(To 650C)

Valves, fittings and

other irregular profiles

Above ground
Frequent mechanical impact
Heavy abrasion

Steelcoat 400 System

Penetrating Primer
Densyl Supersoft Mastic
Ultraseal tape
Urethane Topcoat

(To 650C)

Note: In colder climates, it is suggested that Densopol 60HT is substituted for Densopol 60.

13

Denso Corrosion Protection Systems

DENSO PETROLATUM SYSTEM
The Denso Multi-purpose long life corrosion protection system
is a multi-component system which remains permanently
plastic and flexible and offers excellent conformability and
shelf life. Based upon blended Petrolatum and selected
inhibitors the system provides unrivalled corrosion protection
in terms of surface preparation requirements and ease of
application. It is typically used for in-situ and shop application
alike.

STEELCOAT 400 SYSTEM

Denso Steelcoat 400 System comprising of penetrating primer
(Denso Penetrating Primer), an easily applied layer of semicoated acrylic backed bitumen tape (Denso Ultraseal Tape) and
a choice of final topcoats (Denso Acrylic or Urethane Topcoat).
The final topcoat can be reinforced with a selected reinforcing
scrim (Denso D5 or D10 Scrim) for sections of steelwork or
pipework which require additional impact resistance. After
priming, Densyl Supersoft Mastic is first utilised to seal and
profile back to back angles, voids, flanges or fittings, before
application of Denso Ultraseal Tape and selected topcoat.

ULTRAFLEX 1500 SYSTEM

The Ultraflex 1500 System comprises Denso Primer D and
Ultraflex 1500 Tape. The Ultraflex 1500 System presents one
of the most rugged pipewraps ever developed, combining
both durability and hi-conformability. This combined with a
specially callendered hi-impact PVC backing, results in impact
resistance values, unrivalled by other pipe coating products.
The Ultraflex 1500 System is characterised by superb
adhesion to self, to steel and shop coatings and when applied
with a 55% overlap results in a 3000 microns finished coating
thickness.

14

Denso Corrosion Protection Systems

product description & carton quantities
Product Description

Units / Carton

Denso MP Primer - 4kg tin

(Also available in 1kg tin and 20kg drum)

Denso Mastic - 3kg block

Densyl Supersoft Mastic - 3kg

Denso Tape
50mm x 10m roll

36

75mm x 10m roll

24

100mm x 10m roll

18

150mm x 10m roll

12

200mm x 10m roll

300mm x 10m roll

Densyl Tape
50mm x 10m roll

36

75mm x 10m roll

24

100mm x 10m roll

18

150mm x 10m roll

12

Densyl KF ColourTape
50mm x 10m roll

36

75mm x 10m roll

24

100mm x 10m roll

18

150mm x 10m roll

12

Denso PVC Self-Adhesive Tape

50mm x 30m roll

40

100mm x 30m roll

20

150mm x 30m roll

15

Denso Primer D 4lt Tin

Denso Ultraflex 1500 100mm x 10m roll

12

Denso Ultraflex 1500 150mm x 10m roll

Densopol 60 HT 50mm x 10m roll

18

Densopol 60 HT 100mm x 10m roll

Densopol 60 HT 150mm x 10m roll

Denso Penetrating Primer - 4lt Tin

Denso Acrylic Top Coat - 4lt Tin (Available in White & Lt. Aircraft Grey)

Denso Ultraseal Tape 50mm x 15m roll

20

Denso Ultraseal Tape 100mm x 15m roll

12

Denso Ultraseal Tape 150mm x 15m roll

Denso Ultraseal Tape 225mm x 15m roll

Denso Ultraseal Tape 475mm x 15m roll

15

Buttweld Fittings

90 Elbow (Long)

T (STRAIGHT)

90 Elbow (Short)

T (REDUCING)

45 Elbow (Long)

REDUCER (CONCENTRIC)

180 RETURN BEND (Long)

180 RETURN BEND (SHORT)

REDUCER (ECCENTRIC)

CAP

Buttweld Pipe Fittings are the recognised standard for leak-proof pipe fabrication in medium and
high pressure systems and in pipelines handling corrosive and hazardous fluids.
OneSteel carries premium quality buttweld fittings covered by major international oil and
petrochemical company approvals, and an alternative low-cost range of OneSteel approved
fittings for other applications.
All stock carbon steel buttweld fittings comply fully with the material and manufacturing
standards detailed here, with the added advantage of .23% maximum carbon content for
optimum weld-joint integrity.

DIMENSIONAL SPECIFICATIONS
ASME B16.9: Steel buttweld fittings. Covers dimensions and tolerance of buttweld fittings 15 to 600mm.
B16.9
LONG RADIUS WELDING ELBOWS, RETURN BENDS & CAPS

SHORT RADIUS WELDING ELBOWS

& RETURN BENDS

STRAIGHT TEES

REDUCING TEES

CONCENTRIC & ECCENTRIC REDUCERS

90

45

180

90

180

ASME B16.25: Buttweld ends. Covers the preparation and design details of buttweld ends for all components of

buttwelded pipe systems.
MSS SP-48:

16

Steel buttweld fittings 650mm and larger. Covers dimensions and tolerance of long radius elbows,
tees and reducers in sizes 650 to 900mm.

Buttweld Fittings
MATERIAL SPECIFICATIONS
SEAMLESS CARBON STEEL: Buttweld fittings are made to the material specifications of ASTM A234, grades WPA,
WPB or WPC; which correspond exactly to the material specifications of seamless carbon steel pipes to ASTM A106
grades A, B, or C.
AUSTENITIC STAINLESS STEEL FITTINGS: OneSteel stocks stainless steel fittings in ASTM grades 304L
and 316L. Other grades available to order.
LOW TEMPERATURE FITTINGS: For low temperature applications, a wide range of fittings in materials to ASTM
A420 can be offered.
HIGH YIELD FITTINGS: On an indent basis, we offer a range of fittings having a high yield strength suitable for use
with the various grades of API 5LX linepipe.
FERRITIC ALLOY STEEL FITTINGS: For high temperatures, OneSteel offers a range of alloy fittings to
ASTM specification A335, in the following grades:

P1 - 1/2%Mo
P5 - 5%CR1/2%Mo
P7 - 7%Cr 1/2%Mo
P9 - 9%Cr1%Mo

P11 - 11/4%Cr1/2%Mo
P12 - 1%Cr1/2%Mo
P22 - 21/4%Cr1%Mo

WORKING PRESSURES
Buttweld fittings are designed and manufactured to standards which demand a bursting strength equal to or greater
than that of Seamless Pipe of the same material specification, nominal diameter and wall thickness, and their
allowable working pressures are equal to those shown for pipe in the OneSteel pipe catalogue. Maximum allowable
working pressures for:
CARBON STEEL FITTINGS: Equal to seamless pipes to ASTM A106 (Grade B unless otherwise specified).
STAINLESS STEEL: Fittings (Grades 304 and 316, also 304L and 316L) are equal to stainless steel pipes to
ASTM A312 of equal grade and schedule.
HIGH TEMPERATURE (Ferritic Alloy): Fittings (Grades WP5, WP11 etc.), are equal to seamless pipes to ASTM A335
of similar grade (P5, P11, etc.).
LOW TEMPERATURE: Fittings (Grade WPL6-ASTM A420) are equal to seamless pipes to Grade 6 - ASTM A333.
NB: Stainless Steel Fittings in Schedule 10S and 5S are not designed for applications where pressure is a prime
consideration, and the relevant standard, MSS SP43 establishes the working pressures substantially lower than
those yielded by the application of the basic formula.

QUALITY CONTROL
Buttweld fittings from OneSteel are subject to strict quality control. Manufacturers plants are visited regularly, and the
source of mother tube is verified. Test certificates are available as required. OneSteel liaises with major customers to ensure
that all fittings are obtained from sources approved by the customer or by specific industry groups.

17

Buttweld Fittings
CARBON STEEL BUTTWELD FITTINGS TO ASME B16.9, B16.28 & BS.1640
B16.9
LONG RADIUS WELDING ELBOWS, RETURN BENDS & CAPS
B

B16.28
SHORT RADIUS WELDING ELBOWS & RETURN BENDS

45

90

Nominal Sizes shown are ]DN: SI Metric Term

Nom. Size DN
]
l
DN
NPS
1/2
15
3/4
20
25
1
32
1 1/4
40
1 1/2
50
2
65
2 1/2
80
3
90
3 1/2
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
750
30
900
36

180

Sch.
100

15.09
18.26
21.44
23.83
26.19
29.36
32.54
38.89

Sch. Sch. Sch. X.X.

120
140
160
Stg.

4.78
7.47

5.56 7.82

6.35 9.09

6.35 9.70

7.14
10.15

8.74 11.07

9.53 14.02

11.13 15.24

16.15
11.13

13.49 17.12
12.70

15.88 19.05
14.27

18.26 21.95
18.26 20.62 23.01 22.23
21.44 25.40 28.58 25.40
25.4 28.58 33.32 25.40
27.79 31.75 35.71

30.96 36.53 40.49

34.93 39.67 45.24

38.10 44.45 50.01

46.02 52.37 59.54

REDUCING TEES (B16.9)

90

180

l NPS: ASME Term

Wall Thickness (mm)

Pipe
Std.
OD mm Sch. 10 Sch. 20 Sch. 30
Wt. Sch. 40 Sch. 60 X Stg. Sch. 80
21.3

2.77

3.73
26.7

2.87

3.91
33.4

3.38

4.55
42.2

3.56

4.85
48.3

3.68

5.08
60.3

3.91

5.54
73

5.16

7.01
88.9

5.49

7.62
101.6

5.74

8.08
114.3

6.02

8.56
141.3

6.55

9.53
168.3

7.11

10.97
219.1

6.35 7.04
8.18
10.31 12.70
273.1

6.35 7.80
9.27
12.70 12.70 5.09
323.9

6.35 8.38 9.53 10.31 14.27 12.70 17.48

355.6 6.35
7.92
9.53 9.53
11.13 15.09 12.70 19.05
406.4 6.35
7.92
9.53 9.53 12.70 16.66 12.70 21.44
457
6.35
7.92
11.13
9.53 14.27 19.05 12.70 23.83
508 6.35 9.53 12.70 9.53 15.09 20.62 12.70 26.19
610
6.35 9.53 14.27 9.53 17.48 24.61 12.70 30.96
762
7.92 12.70 15.88 9.53

12.70

914
7.92 12.70 15.88 9.53 19.05

12.70

STRAIGHT TEES (B16.9)

38
38
38
47.5
57
76
95
114
133
152
190
229
305
381
457
533
610
686
762
914
1143
1372

16
19
22
25.4
29
35
44.5
51
57
63.5
79
95
127
159
190
222
254
286
318
381
470
565

47.5
43
55.5
70
82.5
106
132
159
184
210
262
313
414
517
619
711
813
914
1016
1219
1524

19
25.4
32
38
51
63.5
76
89
102
127
152
203
254
305
356
406
457
508
610
762
914

33
41
52
62
81
100
121
140
159
197
237
313
390
467
533
610
686
762
914
1143
1372

E. Std.
Wt.
& Ex.
Stg.
25.4
25.4
38.1
38.1
38.1
38.1
38.1
50.8
63.5
63.5
76.2
88.9
102
127
152
165
178
203
229
267
267
267

Nom. Size DN
]
l
DN
NPS
1/2
15
3/4
20
25
1
32
1 1/4
40
1 1/2
50
2
65
2 1/2
80
3
90
3 1/2
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
750
30
900
36

Nominal Sizes shown are ]DN: SI Metric Term

Nominal Size
DN ]
NPS l
Large Small Large Small
End
End
End
End
3/4
20
3
20
/4
1/2
15
25
1
3/4
25
1
20
1/2
15
32
1 1/4
25
1
32
1 1/4
3/4
20
1/2
15
40
1 1/2
32
1 1/4
25
1
40
1 1/2
3/4
20
1/2
15
50
2
40
1 1/2
50
2
32
1 1/4
25
1
3/4
20
2 1/2
65
50
2
40
1 1/2
65
2 1/2
1
32
1 /4
25
1
80
3
1
65
2 /2
50
2
80
3
40
1 1/2
32
1 1/4
25
1
90
3 1/2
80
3
90
3 1/2
65
2 1/2
50
2
40
1 1/2

28.6
28.6
38.1
38.1
38.1
47.6
47.6
47.6
47.6
57.2
57.2
57.2
57.2
57.2
63.5
63.5
63.5
63.5
63.5
76.2
76.2
76.2
76.2
76.2
85.7
85.7
85.7
85.7
85.7
85.7
95.3
95.3
95.3
95.3
95.3

NOTE: All dimensions are in millimetres (mm)

18

l NPS: ASME Term

M
H
Nominal Size
DN ]
NPS l
Large Small Large Small
End
End
End
End
100
4
28.6
38.1
90
3 1/2
80
3
100
4
38.1
50.8
65
2 1/2
38.1
50.8
50
2
40
1 1/2
47.6
50.8
125
5
47.6
50.8
100
4
47.6
50.8
90
3 1/2
125
5
80
3
57.2
63.5
65
2 1/2
57.2
63.5
50
2
57.2
63.5
150
6
57.2
63.5
125
5
100
4
150
6
60.3
76.2
90
3 1/2
57.2
76.2
80
3
50.8
76.2
65
2 1/2
44.5
76.2
200
8
150
6
69.9
88.9
125
5
200
8
66.7
88.9
100
4
63.5
88.9
80
3
57.2
88.9
250
10
200
8
250
10
82.6
88.9
150
6
76.2
88.9
125
5
73.0
88.9
100
4
69.9
88.9
300
12
69.9
88.9
250
10
300
12
200
8
92.1
102
150
6
88.9
102
100
4
350
14
82.6
102
79.4
102
300
12
350
14
250
10
200
8
150
6

CONCENTRIC & ECCENTRIC

REDUCERS (B16.9)

M
C

105
105
105
105
105
105
124
124
124
124
124
124
143
143
143
143
143
143
178
178
178
178
178
216
216
216
216
216
254
254
254
254
254
279
279
279
279
279

102
98.4
95.3
88.9
85.7
117
114
111
108
105
137
130
127
124
121
168
162
155
152
203
194
191
184
241
229
219
210
270
257
248
238

102
102
102
102
102
127
127
127
127
127
140
140
140
140
140
152
152
152
152
178
178
178
178
203
203
203
203
330
330
330
330

Nominal Size
DN ]
NPS l
Large Small Large Small
End
End
End
End
400
16
350
14
300
12
400
16
250
10
200
8
150
6
450
18
400
16
350
14
450
18
300
12
250
10
200
8
500
20
450
18
400
16
500
20
350
14
300
12
250
10
200
8
600
24
500
20
450
18
600
24
400
16
350
14
300
12
250
10
750
30
600
24
750
30
500
20
450
18
400
16
900
36
750
30
900
36
600
24
500
20
450
18

305
305
305
305
305
305
343
343
343
343
343
343
381
381
381
381
381
381
381
432
432
432
432
432
432
432
559
559
559
559
559
673
673
673
673
673

305
295
283
273
264
330
330
321
308
298
368
356
356
346
333
324
432
419
406
406
397
384
533
508
495
483
635
610
584
572

356
356
356
356
356
381
381
381
381
381
508
508
508
508
508
508
508
508
508
508
508
508
610
610
610
610
610
610
610
610

Buttweld Fittings
MASS
(weight)
SIZE
mm

15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750

900 Elbows
LONG RAD
SHORT RAD
Approx. Weight (kg)
STD
XS
STD
XS
0.08
0.10

0.08
0.10

0.15
0.20
0.10

0.26
0.34
0.17

0.38
0.48
0.25
0.33
0.68
0.91
0.45
0.60
1.32
1.73
0.88
1.14
2.08
2.78
1.38
1.83
2.92
3.96
1.93
2.61
3.95
5.40
2.62
3.58
6.67
9.34
4.42
6.21
10.39
15.47
6.89
10.25
20.87
31.34
13.83
20.68
36.97
49.44
24.49
32.89
53.98
71.22
36.06
47.17
69.85
91.63
46.27
61.24
91.17
120.20
61.24
80.29
116.12
153.32
77.57
102.06
143.79
190.06
96.16
126.10
174.64
230.43

207.75
274.88
138.35
183.25
244.49
323.42

326.59
432.28
217.73
287.58
471.74
625.97
313.89
414.14

450 Elbows
LONG RAD
Approx. Wt.
STD
XS
0.04
0.05
0.04
0.05
0.11
0.14
0.17
0.22
0.23
0.29
0.37
0.49
0.74
0.95
1.10
1.47
1.49
2.90
1.96
2.66
3.31
4.63
5.13
7.58
10.34
15.42
18.33
24.45
26.99
35.52
34.70
45.36
45.36
59.88
58.06
76.20
71.67
94.35
87.09
114.76
103.87
141.52
122.02
161.03
162.39
215.46
234.96
311.17

1800 Returns
LONG RAD
SHORT RAD
Approx. Weight (kg)
STD
XS
STD
XS
0.16
0.20

0.16
0.20

0.31
0.40
0.21

0.53
0.69
0.35

0.76
1.00
0.50
0.66
1.36
1.85
0.90
1.22
2.67
3.50
1.78
2.32
4.19
5.62
2.78
3.72
5.90
7.98
3.90
5.31
7.94
10.98
5.26
7.30
13.47
18.96
8.94
12.56
20.91
31.25
13.93
20.73
41.91
63.50
27.94
42.00
74.39
100.25
49.44
66.48
109.32
143.79
72.58
95.26

Reducers

STD

0.07
0.13
0.17
0.26
0.41
0.77
1.00
1.36
1.63
2.77
3.95
6.49
10.70
15.01
26.85
33.11

Caps
CON & ECC
Approx. Weight (kg)
XS
STD
XS

0.10

0.16
0.10
0.14
0.23
0.14
0.18
0.34
0.18
0.23
0.57
0.27
0.32
1.01
0.41
0.45
1.36
0.64
0.82
1.89
0.95
1.27
2.27
1.13
1.54
3.92
1.91
2.59
5.94
2.95
4.10
9.84
5.00
7.30
14.47
9.10
11.80
19.78
13.60
17.20
35.35
15.90
20.80
44.00
20.00
26.30

26.00
34.00

33.00
43.00

46.00
61.00

TEES Straight and Reducing

Note: Weights given for reducing Tees are based on branch one size smaller than run size.
RUN
15
20
25
32
40
50
65
80

BR
15
16
20
15
25
20
32
25
40
32
50
40
65
50
80
55

STD
0.11
0.10
0.17
0.15
0.34
0.29
0.61
0.53
0.92
0.80
1.34
1.21
2.36
2.08
3.37
3.09

XS
0.16
0.13
0.21
0.19
0.42
0.36
0.74
0.66
1.12
1.00
1.69
1.54
2.92
2.61
4.29
3.90

RUN

BR
90
80
100
90
125
100
150
125
200
150
250
200
300
250
350
300

90
100
125
150
200
250
300
350

19

STD
4.47
4.09
5.72
5.26
8.98
8.21
13.29
21.11
24.36
22.09
41.37
37.65
59.88
54.89
76.20
65.32

XS
5.72
5.31
7.44
6.94
4.98
10.98
19.05
17.15
34.66
31.93
53.52
49.44
75.75
70.31
92.08
84.37

OLet Fittings
weldOLETS
Used to make full size and reducing branch connections from 6 to 750mm
from run pipes 10 to 900mm in order to:

Facilitate header construction.

Construct the joint to full pipe strength.

Meet code design requirements for reinforced branch joints.

Improve flow.

Assure economical, clean and strong connections.

Weldolet

Thredolet

Sockolet

THREDOLETS AND SOCKOLETS

Used for making relatively small branch outlet connections.
Threadolets and Sockolets are half couplings that are bevelled for convenience,
tapered for strength, flared for fluid flow and drop forged for the ultimate in
strength and ruggedness.
Elbolet

ELBOLETS AND LATROLETS

Used for making threaded, socket-weld or buttweld outlets tangentially to elbows
or as 45 branch connections on straight pipe. The design provides for a full
penetration weld. These fittings provide greatly improved flow conditions compared
with 90 connections and are advantageous for many instrument connection
applications.

Latrolet

INSTALLATION GUIDE
Less fit up time is required for Olets than for
most other fittings or fabricated connections. When
proper welding procedure is followed, the resultant cost
is more economical than constructing branch connections
by any other method.

BRANCH
PIPE

WELD
ROOT
GAP

ROOT
GAP

OR

20

45

HEADER
PIPE

ROOT
GAP

1.6mm MAX.
CONSOLIDATION
GAP

HEADER
OUTSIDE
SURFACE

OLet Fittings
RANGE OF OLETS
The following range of Olets are available:
Weldolets Thredolets Sockolets Elbolets

Latrolets

Nipolets

15mm

Sweepolets

HOW IT WORKS
Each outlet size indicated on chart is designed to fit a number of run pipe sizes, e.g. The 15mm
fitting marked 900-100x15 will fit all run pipe sizes from 100mm to 900mm. When placed on a
900mm run pipe, there will be a maximum gap of 1.6mm between the top of the run pipe and the
base of the fitting at the crotch as shown on sketch. This gap is negligible when welding.

1.6mm MAX
GAP
900mm RUN PIPE

SIZE SELECTION CHART

Standard Weight and Extra Strong Weldolets, Sockolets and 3000# Thredolets
10 x 6
15 x 6
25 - 20 x 6
65 - 32 x 6
900 - 80 x 6
10 x 8
15 x 8
25 - 20 x 8
65 - 32 x 8
900 - 80 x 8
15 x 10
25 - 20 x 10
65 - 32 x 10
900 - 80 x 10
15 x 15
20 x 15
25 x 15
40 - 32 x 15
65 - 50 x 15
200 - 80 x 15
900 - 250 x 15

20 x 20
25 x 20
40 - 32 x 20
65 - 50 x 20
125 - 80 x 20
300 - 150 x 20
900 - 350 x 20
25 x 25
32 x 25
40 x 25
50 x 25
65 x 25
90 - 80 x 25
125 - 100 x 25
250 - 150 x 25
900 - 300 x 25
32 x 32
40 x 32
50 x 32
65 x 32
90 - 80 x 32
125 - 100 x 32
200 - 150 x 32
900 - 500 x 32

40 x 40
50 x 40
65 x 40
80 x 40
100 - 90 x 40
150 - 125 x 40
300 - 200 x 40
600 - 350 x 40
900 - 650 x 40
50 x 50
65 x 50
80 x 50
90 x 50
100 x 50
125 x 50
150 x 50
250 - 200 x 50
450 - 300 x 50
900 - 500 x 50

65 x 65
90 x 90
80 x 65
100 x 90
90 x 65
125 x 90
100 x 65
150 x 90
125 x 65
200 x 90
150 x 65
250 x 90
200 x 65
350 - 300 x 90
300 - 250 x 65
500 - 400 x 90
450 - 350 x 65
900 - 600 x 90
900 - 500 x 65
100 x 100
80 x 80
125 x 100
90 x 80
150 x 100
100 x 80
200 x 100
125 x 80
250 x 100
150 x 80
350 - 300 x 100
200 x 80
500 - 400 x 100
250 x 80
900 - 600 x 100
350 - 300 x 80
Outlet Sizes:
500 - 400 x 80 125, 150, 200, 250, 300,
900 - 600 x 80 350, 400, 450, 500, 600,
650, 750
Order to specific size
combination.

6000# Thredolets, Schedule 160 and Double Extra Strong Sockolets

20 x 15
32 x 15
65 x 15
900 - 200 x 15
25 x 20
65 - 32 x 20
250 - 80 x 20
900 - 300 x 20

40 - 32 x 25
65 - 50 x 25
250 - 80 x 25
900 - 300 x 25

40 x 32
65 - 50 x 32
90 - 80 x 32
200 - 100 x 32
500 - 250 x 32
900 - 600 x 32

50 x 40
65 x 40
90 - 80 x 40
125 - 100 x 40
200 - 150 x 40
450 - 250 x 40
900 - 500 x 40

65 x 50
80 x 80
100 x 50
125 x 50
150 x 50
250 - 200 x 50
500 - 300 x 50
900 - 600 x 50

Schedule 160 and Double Extra Strong Weldolets

15 x 15
32 - 20 x 15
900 - 40 x 15
20 x 20
32 x 20
40 x 20
200 x 20

25 x 25
65 - 32 x 25
250 - 80 x 25
900 - 300 x 25
40 - 32 x 32
65 - 50 x 32
250 - 80 x 32
900 - 300 x 32

40 x 40
65 - 50 x 40
90 - 80 x 40
200 - 100 x 40
400 - 250 x 40
900 - 600 x 40

50 x 50
65 x 50
90 - 80 x 50
125 - 100 x 50
200 - 150 x 50
450 - 250 x 50
900 - 500 x 50

21

Outlet Sizes:
65, 80, 100, 125, 150,
200, 250, 300.
Order to specific size
combination.

High Pressure Fittings

SCREWED & SOCKET-WELD 3000 & 6000 lb
The high pressure pipe fittings illustrated
in the following pages are designed for
use with American Standard Linepipe
and are used extensively in the
fabrication of screwed or socket-weld
high pressure piping systems.
90 ELBOW

They are found throughout refinery,

petrochemical and industrial plants,
on pressure vessels, hydraulic lines,
refrigeration plants and wherever high
pressures and/or temperatures occur.

Pipe/Fitting combinations are as follows:

Fitting Pressure
Corresponding Max.
Class
Pipe Schedule
Threaded Fittings
3000 lbs
Sch. 80
6000 lbs
XXS
Socket-Weld Fittings
3000 lbs
Sch. 80
6000 lbs
Sch. 160

90 ELBOW

45 ELBOW
45 ELBOW

DIMENSIONAL SPECIFICATIONS
TEE

ASME B16.11 Forged Steel Fittings,

Socket-Weld and Threaded.

BS3799 - Forged Steel Pipe

Fittings, screwed and socket-weld
for the petroleum industry - based
on ASME B16.11.

TEE

MATERIAL SPECIFICATIONS
CROSS

COUPLING

Carbon Steel forgings to

ASTM A105, or Barstock.

Stainless and Alloy Steels to
ASTM A182 of the appropriate
grades, including:

Grade F11 (Chrome-Moly, for high

temperatures), Grade F316L
(Stainless Steel, for temperature and
corrosion resistance).

CROSS

ASTM A350 Gr-LF1 (Carbon Steel

for low temperatures).
COUPLING

WORKING PRESSURES
PRESSURE/TEMPERATURE RATINGS

UNION

HEXAGON
HEAD PLUG

38

66

93

121

149

177

SERVICE TEMPERATURE CELSIUS

204 232 260 288 316 343 371

399

427 427* 482* 510 538

CAP

3000 lb 20670 20359 20084 19808 19602 19360 19119 18706 17948 16949 15915 14813 13504 12229 10507 8612 6373 4409 2445
6000 lb 41340 40754 40168 39617 39232 38756 38239 37412 37412 33933 31831 29627 27008 24459 21014 17225 12780 8853 4926
Non-shock Working Pressures tabulated in kPa
*These pressures are in accordance with the ANSI Code for Pressure Piping (ASME B31.1).
Suggest Alloy Steel above 482C.

HEXAGON
HEAD BUSHING

All high pressure fittings must be used within the pressure/temperature limitations of the
pipes to which they are attached.
ROUND
HEAD PLUG

TYPE 2

FINISH
Fittings are normally self-coloured or phosphate-finished. Galvanised or cadmium-plated
finish is available at extra cost.

SQUARE
HEAD PLUG

22

TYPE 1

SOCKET WELDING REDUCER INSERTS

Nominal
Pressure
Ratings

High Pressure Fittings

Standard Range: SCREWED NPT. (BSP available to order).

90 ELBOW

45 ELBOW

Hexagonal
Nipple

CROSS

90 Elbow
45 Elbow
Tee
Coupling
Half Coupling
Cap
Cross
Hexagonal
Nipple

TEE

3000 lb
a
a
a
a
a
a
a
a

6000 lb
a
a
a
a
a
a
a
a

All conform to 6000

lb rating
Hexagonal Plug
a
a
Round Head Plug
a
a
Square Plug
a
a
Bush
a
a

Coupling

Hexagonal Plug

Half Coupling

Round Head
Plug

Size Range
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm

Normal Manufacture
Forged
Forged
Forged
Barstock
Barstock
Barstock
Forged

6-100mm

Forged or Barstock

6-100mm
6-100mm
6-100mm
6-100mm

Forged or Barstock
Barstock
Barstock
Forged or Barstock

Square
Plug

Cap

Bush

Standard Range: SOCKET-WELD

90 ELBOW

90 Elbow
45 Elbow
Tee
Coupling
Half Coupling
Cap
Cross

Tee Equal
& Reducing

45 ELBOW

3000 lb

6000 lb

a
a
a
a
a
a
a

a
a
a
a
a
a
a

Size Range
8-80mm
8-80mm
8-80mm
8-80mm
8-80mm
8-80mm
8-80mm

Coupling
Equal & Reducing

Half
Coupling

Cap

Cross

Normal Manufacture
Forged
Forged
Forged
Barstock
Barstock
Barstock
Forged

23

High Pressure Fittings

SCREWED & SOCKET-WELD 2000, 3000 & 6000 lb
Screwed Fittings are taper-threaded in accordance with ASME B1.20.1, having thread lengths in accordance with applicable
tables.
The actual and theoretical axes of the threads may diverge by not more than 1.6 mm in 300 mm.
Fittings can be threaded to British Standard Taper (BS 21) if required. ASME B 1.20.1, the American Standard for
pipe threads, determines length of thread engagement as shown below.

SIZE 6
A
7.93
mm

8
9.52

10
11.11

Length of Thread Screwed into Valves or Fittings

15
20
25
32
40
50
65
80
90
100 125 150
12.7 14.28 17.46 17.46 17.46 17.46 23.81 24.6 26.98 28.57 30.16 30.16

Socket-Weld Fittings are designed for welding to American standard pipes (3000 lb. fittings to Sch. 80 pipe
and 6000 lb. fittings to Sch. 160 pipe).

0.8C
PIPE
C

FITTING

FITTING
1.6mm

C
C

PIPE

C MINIMUM = 11/4t
BUT NOT LESS THAN 4mm
t = NOMINAL PIPE
WALL THICKNESS

Minimum dimensions required for socket-weld

fittings as specified in the American Standard Code
for Pressure Piping, ASME B31.1.

UNIONS SCREWED & SOCKET-WELD

Dimensions for high pressure unions are listed in BS 3799. Dimensions may vary according to manufacturers
specifications.

SCREWED UNIONS

SOCKET-WELD UNIONS

Alternative Collar
Alternative Collar

24

Alternative Collar

High Pressure Fittings

TUBULAR FITTINGS
SWAGE NIPPLES
Ends Screwed, Plain or Bevelled for
Welding, Concentric and Eccentric.

PIPE NIPPLES

CLOSE-TAPER NIPPLES

Seamless Tubular, Ends Screwed,

Plain or Bevelled.

Seamless Tubular, Screwed.

Swage Nipples as illustrated are manufactured

fromSeamless Steel Pipe to ASTM A106,
Grade B. They can also be machined from
Barstock material.

Swage and Pipe Nipples can also be supplied with non-standard end connections
e.g. One End Screwed, One End Bevelled, or One End Sch. 80, One End Sch. 40.

BUTTWELD TYPE

PLAIN END TYPE

SCREWED TYPE

PLAIN END

BEVEL END

OneSteel offers a range of Swage

and Pipe Nipples in a wide variety of
diameters, lengths, wall thicknesses
and materials.
Please consult us for your
requirements.

SOCKET-WELD REDUCER INSERTS

ASTM A105 FORGINGS
The purpose of socket-weld reducer inserts is to avoid the
delays and extra costs that naturally occur in producing
regular socket-weld fittings with reduced outlets. Designed
for use with straight size fittings, reducer inserts serve the
same purpose as threaded bushings used with screwed
fittings. The drawing at right illustrates the simplicity of their
application.
TYPE 1
For use with Schedule 40 & 80 pipe.

REDUCER INSERT

FITTING
PIPE

TYPE 2
For use with Schedule 160 pipe.

SIZE RANGE: From 15 x 10mm to 100 x 25mm, in all standard reducing sizes.

25

Flanges to American Standards

SPECIFICATIONS
Forged Carbon, Alloy and Stainless Steel Flanges to American Standards are
designed for use with pipes and fittings to American Standards, but can also be
attached, in certain sizes to pipes made to British and Australian Standards.

SIZES 15 - 600mm
CLASS 150, 300, 400, 600, 900, 1500 & 2500
Dimensions shown are for Flanges made to the dimensional requirements of
ASME B16.5 which is the accepted American Standard for all Flanges in sizes to
600mm bore.

SIZES ABOVE 600mm

Steel Flanges above 600mm bore are made to various standards, as follows:
CLASS 150, 300, 400, 600, 900
Dimensions to MSS-SP44* or BS 2393. OneSteel stocks slip-on and
weld-neck flanges to BS 3293 and blinds to MSS SP44.
*MSS-SP44
A Standard developed by the Manufacturers Standardisation Society (of the Valves and Fittings
Industry) to provide uniform dimensions of flanges for use with high pressure pipelines larger than
600mm diameter. These designs were predicated on flanges being used with API 5LX line-pipe of
52,000 lbs. minimum yield strength, and were proportioned accordingly.
This Standard can be taken as being the extension of ASME B16.5 in sizes above 600mm bore.

26

ANSI FLANGES

Flanges to American Standards

ANSI FLANGES
MATERIAL SPECIFICATIONS
American Standard Pipe Flanges are manufactured in a variety of Carbon, Alloy and Stainless Steels and selection of a
particular grade is determined by the usual criteria of pressure/temperature requirements and corrosion resistance.
Since these factors determine pipe and fittings to be used in a piping system, it is then necessary only to select flanges of a
similar material.

LARGE DIAMETER FLANGE STANDARDS

ASME B16.1b
This Standard establishes dimensions for Class 250 Cast Iron Flanges above 600mm,
(as ASME B16.1 gives dimensions for large diameter Class 125 Cast Iron Flanges).
API 605
American Petroleum Institute Standard intended primarily for use in Oil and Gas production. API 605 dimensions DO NOT
match ASME, MSS or BS dimensions of
similar pressure class.
AWWA C207-54T
This is a Standard published by the American Waterworks Association for steel
Flanges to be used on waterworks and sewerage pipes. These flanges match
Class 125 Cast Iron Flanges (ASME B16.1) in most dimensions.
CLASSES125LW, 175 & 350
These are Standards developed over the years by a number of manufacturers, not all using exactly the same dimensions.
TEMA FLANGES
The Tubular Exchangers Manufacturers Association (TEMA) lays down standards for dimensions and material
specifications for Shell Flanges, Cover Flanges, Long Welding Necks for Nozzles and other heat exchanger components.
BS.3293
This British Standard established dimensions for flanges for petroleum industry use,
in Class 150, 300, 400 and 600, in sizes above 600mm, which correspond exactly to those of MSS SP-44 in Class 300, 400
and 600.
Class 900 is not included in the British Standard, but
dimensions are given for Class 150, 600-700mm which are
similar to those of ASME B16.1, Class 125.
BS.1560
This British Standard is based on ASME B16.5, and lists Steel
Pipe Flanges to the
same dimensions, pressure classes and in the same sizes as
the American Standard up to 600mm.

The classifications are used to group materials for Flanges Class

150 through Class 2500.
ASTM Specifications directly covering forged flanges for these
general materials specifications do not presently exist. Flanges
of these materials shall be specified to conform to the nearest
grade in A182, except chemistry to conform to the ASTM
specification listed.
Intended primarily for use for subzero service. The ratings at
-29 to 38C given for the materials on page 28 shall also apply
at lower temperatures.

Guide to Material Specifications

General Classification
Applicable ASTM
Specification - Forgings
Carbon Steel (Refer Table pg. 28)
Carbon Steel (low temp.)
Carbon Molv (Refer Table pg. 28)
Chrome-Moly Alloy Steels
1/2 Cr 1/2 Mo
1 Cr 1/2 Mo
1 1/4 Cr 1/2 Mo
2 1/4 Cr 1 Mo
3 Cr 1 Mo
5 Cr 1/2 Mo
5 Cr 1/2 Mo-Si
9 Cr 1 Mo
Chrome-Nickel Stainless Steels
Type 304
Type 310
Type 347
Type 321
Type 316
H & L Grades also available
Nickel Steel
3 1/2 Ni.

27

A105
A350 Grade LFI
other grades also available
A182-55T Grade F1
A335 Grade P2
A182 Grade F12
A182 Grade F11
A182 Grade F22
A335 Grade P21
A182 Grade F5a
A335 Grade P5b
A182 Grade F9
A182 Grade F304
A182 Grade F310
A182 Grade F347
A182 Grade F321
A182 Grade F316
A350-55T Grade LF3

Flanges to American Standards

ASTM A105
Chemical Requirements
Note - For each reduction of 0.01% below the specified carbon maximum
(0.35%), an increase of 0.06% manganese above the specified maximum
(1.05%) will be permitted up to a maximum of 1.35%.
Element
Composition, %
Carbon
0.35 max
Manganese
0.60-1.05
Phosphorus
0.040 max
Sulfur
0.050 max
Silicon
0.10-0.35
Copper
0.40 maxA
Nickel
0.40 maxA
Chromium
0.30 maxA,B
Molybdenum
0.12 maxA,B
Vanadium
0.03 maxC
Columbium
0.02 maxC
A
The sum of copper, nickel, chromium and molybdenum shall not exceed
1.00%.
B
The sum of chromium and molybdenum shall not exceed 0.32%.
C
By agreement between the manufacturer and the purchaser, the limits for
vanadium and columbium, or both, may be increased to 0.10% and 0.05%
respectively.

Temperature
in 0C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
540

Mechanical Requirements - nominal *

Tensile strength, min, MPa
485
Yield strength, min, MPac
250
Elongation in 50mm, min %
30
Reduction of area, min %
30
Hardness, HB, max
187
*For complete explanation, refer detailed specification, Table 3, ASTM A
105/A105M.
Heat treatment of flange forgings above Class 300 is mandatory under
ASTM A105. All A105 flanges stocked by OneSteel including Class 150 and
300 are heat treated (normalised).

TEMPERATURE / PRESSURE RATINGS

Carbon Steel Pipe Flanges to ASME B16.5 (BS. 1560)
Forgings to ASTM A105 - Not recommended for prolonged use above 4270C
Forgings to ASTM A350 - LF2 - Not to be used above 3430C
Maximum Working Pressure in kPa by PN
PN20
PN50
PN100
PN150
PN250
Class 150
Class 300
Class 600
Class 900
Class 1500
1960
5110
10210
15320
25530
1920
5010
10020
15020
25040
1770
4640
9280
13910
23190
1580
4520
9050
13570
22610
1400
4380
8760
13150
21910
1210
4170
8340
12520
20860
1020
3870
7750
11620
19370
840
3700
7390
11090
18480
740
3650
7290
10940
18230
650
3450
6900
10350
17250
560
2880
5750
8630
14380
470
2000
4010
6010
10020
370
1350
2710
4060
6770
280
880
1760
2640
4400
190
520
1040
1550
2590
130
330
650
980
1630

PN420
Class 2500
42550
41730
38650
37690
36520
34770
32280
30800
30390
28750
23960
16690
11290
7330
4320
2720

FLANGES ABOVE DN 600 ARE NOT INCLUDED IN ASME B16.5 AND THE CLASS DESIGNATIONS IN THESE LARGE DIAMETERS DO NOT IMPLY
SPECIFIC TEMPERATURE/ PRESSURE RATINGS

28

Flanges to American Standards

METHODS OF ATTACHMENT

SLIP - ON FLANGES

WELDING NECK FLANGES

Although recommended practice in attaching Slip-On

type flanges is to weld both at the flange hub and
the pipe end, for mild service conditions only one is
sometimes employed. In this case the weld is normally
made at the pipe end.

This type of flange is attached by buttwelding to the

adjoining pipe or shell. The weld may be made either
manually or automatically with or without a backing
strip. Sound welds are readily obtained with any
recognised welding procedure.

LAP JOINT FLANGES

Lap joint flanges are most frequently used with lap joint
stub ends, (Type A), although in some cases the lap is
formed on the pipe end. Since they are free to rotate
or swivel, there is no problem of bolt hole alignment.
Such joints may be readily broken for inspection,
cleaning, etc. The radius at the ID of the flange face
accommodates that at the back of the lap, thus
permitting more uniform application of loading.

THREADED FLANGES
Threaded flanges are, of course, attached by screwing
to threaded pipe ends.

Lap Joint flanges find their most common application

when used with stainless steel stub ends.

SOCKET-WELD FLANGES
In attaching socket-weld flanges, the pipe end is
inserted into the socket and then welded at the flange
hub. An inside weld at the pipe end is frequently made
for greater strength or, with grinding, to provide a
smooth bore without pockets or recesses.

29

Flanges to American Standards

DN 15 to 600 are to ASME B16.5 (BS 1560). DN 750 & 900 are to BS 3293 for Slip-On & Weldneck only.

Threaded Flange

Slip-On Flange

Socket Welding (DN 15 - 80)

Blind Flanges up to DN600

(Above DN600 see notes
below)

NOMINAL SIZES SHOWN ARE ]DN : SI METRIC TERM lNPS : ASME TERM

]
DN

l
NPS

Dia.
of
Fig.
O

15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900

1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
3 1/2
4
5
6
8
10
12
14
16
18
20
24
30
36

90
100
110
120
130
150
180
190
215
230
255
280
345
405
485
535
600
635
700
815
985
1170

PN20 (Class 150)

PN50 (Class 300)
Length
Thru
Hub
Length
Thru Hub Dia. Dia.
ThickThickDia. Dia.
ness
ness of Thrd. Slip- Weld of of No. of Dia.
of No.
Thrd.
Weld of
of of Fig.
of
Fig. Min. On Soc/
Neck Bolt Bolt Bolts Fig. O Min. Slip-On Soc/ Neck Bolt Bolt Bolts
C(1)* Weld Y(1)* Y(1)* Circle Holes
C(1)* Weld Y(1)* Y(1)* Circle Holes
11.5
16
48 60.5 16
4
95 14.5
22
52 66.5 16
4
13.0
16
52
70.0 16
4
120 16.0
25
57
82.5 20 4
14.5
17
56
79.5 16
4
125 17.5
27
62 89.0 20 4
16.0
21
57
89.0 16
4
135 19.5
27
65 98.5 20 4
17.5
22
62 98.5 16
4
155 21.0
30
68 114.5 22 4
19.5
25
64 120.5 20
4
165 22.5
33
70 127.0 20 8
22.5
29
70 139.5 20
4
190 25.5
38
76 149.0 22 8
24.0
30
70 152.5 20
4
210 29.0
43
79 168.5 22 8
24.0
32
71 178.0 20
8
230 30.5
44
81 184.0 22 8
24.0
33
76 190.5 20
8
255 32.0
48
86 200.0 22 8
24.0
36
89 216.0 22
8
280 35.0
51
98 235.0 22 8
25.5
40
89 241.5 22
8
320 37.0
52
98 270.0 22 12
29.0
44
102 298.5 22
8
380 41.5
62
111 330.0 26 12
30.5
49
102 362.0 26
12 445 48.0
67
117 387.5 30 16
32.0
56
114 432.0 26
12 520 51.0
73
130 451.0 33 16
35.0
57
127 476.0 30 12 585 54.0
76
143 514.5 33 20
37.0
64
127 540.0 30 16 650 57.5
83
146 571.5 36 20
40.0
68
140 578.0 33 16 710 60.5
89
159 628.5 36 24
43.0
73
145 635.0 33 20 775 63.5
95
162 686.0 36 24
48.0
83
152 749.5 36 20 915 70.0
106
168 813.0 42 24
54.0
89
130.2 914.0 35 28 1090 92.0
210
210 997.0 48 28
60.3
95
136.5 1086 41 32 1270 105.0
241
241 1168.0 54 32

Nominal
Flange Size DN
]

DN

15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600

PN150 (Class 900)

Thick- Length Thru Hub
Dia. of Dia. No. Dia.
Dia. ness
l
Thrd.
Weld Bolt of of of Fig.
of of Fig.
NPS Fig. O Min.
Slip-On
Neck Circle Bolt Bolts O
Holes
Y(2)
Y(2)
C(2)
1/2
120
3/4
130
1
150
1 1/4
160
USE PN250 DIMENSIONS IN THESE SIZES
1 1/2
180
215
2
2 1/2
245
3
240 38.5
54
102 190.5 26 8 270
4
295 44.5
70
114 235.0 32 8 310
5
350 51.0
79
127 279.5 35 8 375
6
380 56.0
86
140 317.5 32 12 395
8
470 63.5
102
162 393.5 39 12 485
10
545 70.0
108
184 470.0 39 16 585
12
610 79.5
117
200 533.5 39 20 675
14 640 86.0
130
213 559.0 42 20 750
16
705 89.0
133
216 616.0 45 20 825
18
785 102.0
152
229 686.0 52 20 915
20 855 108.0
159
248 749.5 54 20 985
203
292 901.5 68 20 1170
24 1040 140.0

NOTES:
All dimensions are shown in millimetres - mm.
* 1. The 2mm Raised Face is included in thickness C(1) and length
through hub Y(1). This applies to PN20 and PN50 Pressure
Ratings.
2. The 7mm Raised Face is not included in thickness C(2) and
length through hub Y(2). PN100, 150, 250 and 420 Pressure
Ratings are regularly furnished with 7mm Raised Face which
is additional to the flange thickness C(2) and Y(2).
3. Always specify bore when ordering weldneck flanges.
Bore dimensions shown opposite also provide inside pipe
diameters.
LARGE DIAMETER FLANGES ABOVE DN 600
For Blind Flanges refer to MSS SP44.
BS 3293 covers Slip-On and Weldneck but excludes Blind
Flanges.
MSS SP44 covers Blind and Weldneck but excludes Slip-On
Flanges.
BS 3293 Weldneck PN20 flange thickness, C(1), is less than MSS
SP44 equivalents.
API - 605 Dimensions for Large Diameter Flanges vary
considerably from both BS 3293 and MSS SP44 Details on
request.

30

PN250 (Class 1500)

Thick- Length Thru Hub Dia. Dia.
ness
of No.
Thrd.
Weld of
of Fig.
of
Bolt Bolt Bolts
Min. Slip-On Soc/ Neck Circle
Holes
C(2) Weld Y(2) Y(2)
22.5
32
60 82.5 22
4
25.5
35
70 89.0 22
4
29.0
41
73 101.5 26
4
29.0
41
73 111.0 26
4
32.0
44
83 124.0 30 4
38.5
57
102 165.0 26
8
41.5
64
105 190.5 30 8
48.0
73
118 203.0 33
8
54.0
90
124 241.5 36
8
73.5
105
155 292.0 42
8
83.0
119
171 317.5 39 12
92.0
143
213 393.5 45 12
108.0
159
254 482.5 52 12
124.0
181
283 571.5 56 16
133.5
298 635.0 60 16
146.5
311 705.0 68 16
162.0
327 774.5 76 16
178.0
356 832.0 80 16
203.5
406 990.5 94 16

Raised
Face
Diam.
All Press.
Ratings
mm
35
43
51
64
73
92
105
127
140
157
186
216
270
324
381
413
470
533
584
692
857
1022

Nominal
Size DN
]
DN
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900

O.D.
of
Pipe
l
SCH.
mm
NPS
10
1/2 21.3
3/4 26.7
1 33.4
1 1/4 42.2
1 1/2 48.3
2 60.3
2 1/2 73.0
3 88.9
3 1/2 101.6
4 114.3
5 141.3
6 168.3
8 219.1
10 273.1
12 323.9
14 355.6 342.9
16 406.4 393.7
18 457.0 444.5
20 508.0 495.3
24 610.0 596.9
30 762.0 746.2
36 914.0 898.6

Dia.
of
Fig. O
95
120
125
135
155
165
190
210
230
275
330
355
420
510
560
605
685
745
815
940
1130
1315

Dia.
of
Fig.
O
135
140
160
185
205
235
270
305
355
420
485
550
675
760

Nominal
Flange Size DN

PN100 (Class 600)

Thick- Length Thru Hub Dia. Dia.
ness
of
of No.
of
of Fig. Thrd. Slip- Weld Bolt
Bolt
Neck
On
Soc/
Bolts
Min.
C(2) Weld Y(2) Y(2) Circle Holes
14.5
22
52
66.5 16
4
16.0
25
57
82.5 20 4
17.5
27
62
89.0 20 4
21.0
29
67
98.5 20 4
22.5
32
70 114.5 22
4
26.5
37
73 127.0 20 8
29.0
41
79 149.0 22
8
32.0
46
83 168.5 22
8
35.0
49
86 184.0 26
8
38.5
54
102 216.0 26
8
44.5
60
114 267.0 30 8
48.0
67
117 292.0 30 12
55.5
76
133 349.0 33 12
63.5
86
152 432.0 36 16
66.5
92
156 489.0 36 20
70.0
94
165 527.0 39 20
76.5
106
178 603.0 42 20
83.0
117
184 654.0 45 20
89.0
127
190 724.0 45 24
102.0
140
203 838.0 52 24
114.0
248
248 1022 54 28
124.0
283
283 1194 67 28

PN420 (Class 2500)

Thick- Length Thru Hub Dia.
ness
of
of Fig. Thrd. Slip- Weld Bolt
On Soc/
Neck
Min.
Circle
C(2) Weld Y(2) Y(2)
30.5
40
73
89.0
32.0
43
79
95.0
35.0
48
89 108.0
38.5
52
95 130.0
44.5
60
111 146.0
51.0
70
127 171.5
57.5
79
143 197.0
67.0
92
168 228.5
76.5
108
190 273.0
92.5
130
229 324.0
108.0
152
273 368.5
127.0
178
318 438.0
165.5
229
419 539.5
184.5
254
464 619.0

Dia. No.
of
of
Bolt Bolts
Holes
22
22
26
30
33
30
33
36
42
48
56
56
68
76

]
DN

l
NPS

15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900

1/2
3/4
1
1 1/4
1
1 /2
2
2 1/2
3
3 1/2
4
5
6
8
10
12
14
16
18
20
24
30
36

Nominal Flange
Size DN

4
4
4
4
4
8
8
8
8
8
8
12
12
12

DN

NPS

15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600

1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
4
5
6
8
10
12
14
16
18
20
24

Approximate Welding Neck Flange Bores - mm

SCH.
20

206.4
260.3
311.1
339.8
390.6
441.4
489
590.6
736.6
889.0

SCH.
30

STD.
WT.

205.0
257.5
307.1
336.6
387.4
434.9
482.6
581.1
730.2
882.6

15.8
20.9
26.6
35.1
40.9
52.5
62.7
77.9
90.1
102.3
128.2
154.1
202.7
254.5
304.8
336.6
387.4
438.2
489.0
590.6
743.0
895.4

SCH.
40

SCH.
60

Same as STD. WT.

Nominal
Flange Size DN

303.2
333.3
381.0
428.7
477.8
574.6
876.3

198.5
247.7
295.3
325.4
373.1
419.1
466.8
560.4

EXT.
STG.
13.9
18.9
24.3
32.5
38.1
49.2
59.0
73.7
85.4
97.2
122.3
146.3
193.7
247.7
298.5
330.2
381.0
431.8
482.6
584.2
736.6
889.0

SCH.
80

SCH.
100

Same as EXT. STG.

Welding Neck Flange

242.9
288.9
317.5
363.5
409.5
455.6
547.7

188.9
236.5
281.0
307.9
354.0
398.5
442.9
531.8

SCH.
120

92.1
115.9
139.7
182.6
230.2
273.1
300.0
344.5
387.4
431.8
517.6

SCH.
140

SCH.
160

X.X
STG

177.8
222.3
266.7
292.1
333.3
377.9
419.1
504.9

11.8
15.5
20.7
29.5
34.0
42.9
54.0
66.7

87.3
109.6
131.8
173.1
215.9
257.2
284.2
325.4
366.7
408.0
490.5

6.4
11.0
15.2
22.8
27.9
38.2
45.0
58.4

80.1
103.2
124.4
174.6
222.3
273.1

Flanges to American Standards

GASKET SURFACE
Flanges, and other products designed for bolted connection, when furnished with raised face (or flat face) may
have any type of gasket surface finish that is required. The more common finishes are described in the following
paragraphs.
1 STOCK FINISH:
This is a continuous spiral groove. For
nominal sizes 300mm and smaller it is
generated by a 1.58mm radius roundnosed tool at a feed of 0.79mm per
revolution. For sizes above 300mm the
tool nose is radiused to 3.17mm and the
feed is 1.19mm per revolution.

2 SPIRAL SERRATED:
This too, is a continuous spiral groove,
but it differs from the stock finish in
that the groove is generated with a 90
included angle V tool. The groove is
.39mm deep and the feed is .79mm for
all sizes.

NB OneSteel stocks flanges with

surface finish in the range
3.2-6.3 microns, typically used
with both spiral-wound and
ring gaskets.
4 SMOOTH FINISH:
This finish, which can be produced
by several shapes of tools, shows no
definite tool markings apparent to the
naked eye. In the past this finish was
sometimes known as Smooth Plane.
This term however, should be avoided
because of a tendency to confuse it
with flat faced which, of course,
applies to the flange facing and not to
the gasket surface finish.

5 COLD WATER FINISH:

3 CONCENTRIC SERRATED: (Not illustrated)

As the name suggests this surface
finish is made up of concentric grooves.
A 90 included angle V tool is used
and the grooves are .39mm deep and
.79mm apart.

Produced by using a wide tool at high

speeds, this finish is equivalent to that
of a ground surface. It is mirror-like in
appearance and surfaces finished in this
manner are usually expected to be used
without gaskets.

AMERICAN STANDARD FACINGS To ASME B.16.5

FLAT FACE
RAISED FACE

LAPPED JOINT

RING JOINT

LARGE TONGUE and

GROOVE*

SMALL MALE and FEMALE

SMALL MALE and FEMALE

SMALL TONGUE and GROOVE*

LARGE MALE - FEMALE

*It is necessary to modify facing dimensions in order to furnish slip-on flanges 40mm and smaller and welding neck
flanges with bores larger than Schedule 40, in sizes 40mm and smaller, for large tongue and groove facing.

31

Flange Gaskets
FLANGE GASKETS
Full Face Gaskets: To suit Table D, E and H flanges to AS 2129
Ring Gaskets:
To suit Class 150 and 300lb raised face

flanges to ANSI B16.5
Gasket materials include:

Insertion Rubber
Full face to suit AS 2129 Table D or E. Made from 3mm natural
rubber, usually fabric reinforced. Suitable for liquids and gases at
ambient temperature, within the rated pressure of the flange.
Full Face Rubber Gasket

Compressed Non-Asbestos Fibre

Ring or full face. Usually Klingersil C4430. Suitable for most
liquids and gases including hydrocarbons and steam. AGA
approved (number 5237). Potable water approved to AS 4020.

Spiral Wound Gaskets

Constructed from a spirally wound V section austenitic
stainless steel strip, with a non-asbestos filler between each turn.
Offering high pressure and temperature resistance and ease of
replacement.

Full Face Fibre Gasket

Ring Gasket

There are two popular styles in the Klinger range of spiral gaskets:

Self Centering, medium pressure Type CR

Type CR gaskets have an outer ring which facilitates accurate
centering of the gasket in the joint, provides additional radial
strength, helps prevent blow-out and serves as a reference point
to determine the amount of compression during bolt pullup.
Recommended up to Class 600 flanges or equivalent, general
service. Maximum temperature 350 with graphite filler check
range suitability.

Self Centering, High Pressure Type CRIR

Type CRIR gaskets are the same construction as Type CR but have
an additional inner ring. The inner ring provides additional radial
strength, acts as a barrier to vacuum and corrosive/abrasive
media. Recommended for Class 150 to 2500 flanges or equivalent,
and any application requiring advantages of an inner ring.
Maximum temperatures 540C with graphite filler check flange
suitability. Higher temperature rated materials available on request.
Spiral Gasket
Type CRIR

34

Bolting for ANSI Flanges

BOLTING
To suit R.F. Flange sizes DN 15 to 600 to ASME B16.5 (BS. 1560) and DN 750 & 900 to BS. 3293
L*

Diameter of Bolts is shown in inches. For nominal diameters 1 inch

and smaller, threads are U.N.C.; nominal diameters 1-1/8 inch and
larger threads are 8 U.N. (8 T.P.I.).

Length of Bolts (L) is shown in millimetres rounded to the nearest

5 mm. Stud Bolt lengths (L*) do not include the height of points.
Machine Bolt lengths (L) include the height of point. The length
shown includes the height of the Raised Face in all cases.

*Point Height

STUD BOLT WITH NUTS

MACHINE BOLT WITH NUT

NOMINAL SIZES SHOWN ARE ] DN : SI METRIC TERM l NPS : ASME TERM

Nominal
PN 20 (Class 150)
PN 50 (Class 300)
PN 100 (Class 600) PN 150 (Class 900) PN 250 (Class 1500) PN 420 (Class 2500)
Flange No. Dia.
L
No. Dia.
L
No. Dia.
L
No. Dia.
L
No. Dia.
L
No. Dia.
L
Size DN Bolts Bolts
Bolts Bolts
Bolts Bolts
Bolts Bolts
Bolts Bolts
Bolts Bolts
]
l
ins. Stud Mach.
ins. Stud Mach.
ins. Stud
ins. Stud
ins. Stud
ins. Stud
DN NPS
Bolts Bolts
Bolts Bolts
Bolts
Bolts
Bolts
Bolts
mm mm
mm mm
mm
mm
mm
mm
1/2
1/2
1/2
3/4
3/4
15 1/2
4
60
45
4
65
55
4
80
4
105
4
125
1/2
5/8
5/8 90
3/4
3/4
20 3/4
4
65
50
4
75
60
4
4
115
4
125
1/2
5/8 80
5/8 90
7/8
7/8
USE PN250
25 1
4
65
55
4
65
4
4
125
4
140
1/2
5/8 80
5/8 100
7/8
DIMENSIONS IN
32 1 1/4 4
70
55
4
65
4
4
125
4
1
150
THESE SIZES
1/2
3/4 90
3/4 105
40 1 1/2 4
70
60
4
75
4
4
1
140
4
1 - 1/8 170
5/8
5/8 90
5/8 105
7/8
50 2
4
80
65
8
75
8
8
145
8
1
175
1
5
3
3
65 2 /2 4
/8
90
75
8
/4 100
85
8
/4 120
8
1
160
8
1 - 1/8 195
5/8
3/4 110
3/4 125
7/8
80 3
4
90
75
8
90
8
8
145
8 1 - 1/8 180
8
1 - 1/4 220
5/8
3/4 110
7/8 140
90 3 1/2 8
90
75
8
95
8
5/8
3/4 110
7/8 145
100 4
8
90
75
8
95
8
8 1 - 1/8 170
8 1 - 1/4 195
8
1 - 1/2 255
3/4
3/4 120
125 5
8
90
80
8
100
8
1
165
8 1 - 1/4 190
8 1 - 1/2 250
8 1 - 3/4 300
3/4 100
3/4 125
150 6
8
85
12
105
12
1
170
12 1 - 1/8 195
12 1 - 3/8 260
8
2
345
3/4
7/8 140
200 8
8
110
90
12
110
12 1 - 1/8 195
12 1 - 3/8 220
12 1 - 5/8 290
12
2
380
7/8
250 10
12
115
95
16
1
155
130
16 1 - 1/4 215
16 1 - 3/8 235
12 1 - 7/8 335
12 2 - 1/2 485
7/8 120
300 12
12
100
16 1 - 1/8 170
145
20 1 - 1/4 220 20 1 - 3/8 255
16
2
375
12 2 - 3/4 540
350 14
12
1
130
110
20 1 - 1/8 175
150
20 1 - 3/8 235 20 1 - 1/2 275
16 2 - 1/4 405

Nominal
Flange
Size DN
]

DN

NPS

15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350

1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
3 1/2
4
5
6
8
10
12
14

400 16

16

135

115

20

1 - 1/4

190

160

20

1 - 1/2

255

20

1 - 5/8

285

16

2 - 1/2

445

400

16

450 18

16

1 - 1/8

150

125

24

1 - 1/4

195

170

20

1 - 5/8 275

20

1 - 7/8

325

16

2 - 3/4

495

450

18

500 20

20

1 - 1/8

160

135

24

1 - 1/4

205

180

24

1 - 5/8 290

20

345

16

540

500

20

600 24

20

1 - 1/4

175

145

24

1 - 1/2

230

195

24

1 - 7/8 330

20

2 - 1/2

435

16

3 - 1/2

615

600

24

28
32

1 - 1/4
1 - 1/2

28
32

1 - 3/4

290
325

250
280

28
28

2
355
2 - 1/2 400

750
900

30
36

750 30
900 36

190
215

160
180

PN150, 250 & 420 - NOT LISTED IN BS 3293

Raised Face height of 2 mm for PN20 & 50 and 7 mm for PN100, 150, 250 & 420 is included in dimension L (Bolt Length).

MATERIAL SPECIFICATIONS
ASTM A193 Grade B7
Standard specification for alloy steel and stainless steel bolting materials for high temperature service.
ASTM A194 Grade 2H
Standard specification for carbon and alloy steel nuts for bolts for high pressure and high temperature service.
ASTM A320
Standard specification for alloy steel bolting materials for low temperature service.
Grade L7 covers alloy steel stud bolts.
Grade L4 covers alloy steel nuts to suit Grade L7 stud bolts.

35

Roll Grooved System

OneSteel Piping Systems is the Australian distributor of the Shurjoint and Mech range of roll groove
products.
Shurjoint has over three decades of experience and is recognised as a world
leader in the design and manufacturer of mechanical piping system components.
Shurjoint manufactures the highest quality products by continually investing
in research, engineering and development, which enables them to develop
new and innovative solutions for the changing needs of industry.
Mech is manufactured by the largest pipe fittings manufacturer in the world,
Jinan Meide Casting Co. Jinan Meides core value of quality provides product
of premium levels employing the latest manufacturing technology. MECHs
commitment to quality is reflected in the fact that every product, even down
to the smallest galvanised malleable fitting, is pressure tested. OneSteel
has enjoyed a very successful relationship with Jinan Meide and their MECH
product range. MECH products are sold in over 60 countries and are world
leaders both in quality and value.

The Grooved System is one of the most advanced, versatile, economical and reliable systems available today. After the pipe
ends are grooved, a gasket is stretched over the pipe ends. The coupling segments are then placed over the gasket and bolts
and nuts are fastened resulting in a secure joint.
A coupling can be installed 3-4 times faster than a comparable welded or brazed joint and there is no need for a flame or welding
torch on the job site. A coupling can be installed by fastening a pair of bolts and nuts while using only a spanner, whereas a
comparable flanged joint requires the fastening of many bolts and nuts. The grooved system allows for easy material take-offs
and unlike the threaded system, there is no need to allow for added pipe length for thread engagement. With the removal of
just a few bolts, one can easily access the system for cleaning, maintenance, changes and or system expansion.

Groove

Gasket

Bolt/Nut

36

Housing

Roll Grooved System

RIGID COUPLINGS
Rigid couplings are the most popular and most widely used couplings today. They can be used in applications that require a
rigid joint similar to that of a traditional flanged, welded and or threaded connection.
Angle Pad Design

As the bolts are tightened, the angled bolt pads slide in opposite directions causing
the coupling keys to tightly grip the pipe, while at the same time the grooves are
forced outwards against the coupling keys.

Tongue and Groove Design

The T & G Design mechanism provides a mechanical and frictional interlock

resulting in a rigid joint which reduces undesired angular movement.

Butt-Joint Design

The Unique butt-joint design eliminates the gap in between pipe ends, thus
eliminating not only angular and rotational movement but also axial displacement
under normal service conditions*.

*Pipes must be cut true and square to achieve a butt-joint.

FLEXIBLE COUPLINGS
Flexible couplings allow for full design features in applications such as curved or
deflected layouts and/or when systems are exposed to outside forces beyond normal
static conditions, such are seismic events or where vibration and/or noise attenuation
are a concern. The ability to design in controlled flexibility is an advantageous feature
when compared to traditional rigid jointing methods such as threading, flanging and
welding. When designing with flexible couplings, allow for proper support to the system
so as to eliminate undesired stress.

PIPE SYSTEMS TERMINOLOGY

Rotational Movement

Axial Displacement

Angular Movement

37

Roll Grooved System

The Roll Grooved system allows for:
Reduce space with the use of Suction Diffuser
Time and money savings in installation

Easy system access with removable joints

Good vibration and attenuation performance
Easy alignment of pipe work and valves

Number

Product

Butterfly valve

Suction Diffuser

Flange to Roll Groove Adaptor (Stub)

Flange to Roll Groove Adaptor (Hinged)

Concentric Reducer

Check Valve

Flexible Couplings

Rigid Coupling

Mechanical Tee

Typical Pump Set

COUPLING MATERIALS

Ductile Iron - Standard couplings housings are made of

Ductile Iron.

Stainless Steel - OneSteel offers a variety of stainless steel

materials depending on the intended application.

Gaskets - Available in a variety of configerations and

compounds to meet your specific requirements.

STANDARDS
The roll grooved product range has numerous approvals and standards for the global and local market. Please ask our sales
team about your specific needs.

38

Roll Grooved System - Couplings & Fittings

1GS - Rigid Coupling Light Duty

Can be used in services up to 2070Kpa

and is available in Painted Hot Dipped
Galvanised.
The built-in teeth on the coupling
grip the groove shoulder and serve to
reduce linear movement.
The T&G mechanism features a slight
offset at the foot of the coupling
halves which serve to protect the
gasket from exposure.
With the T&G style coupling no
metal-to-metal contact of the pads is
required. There is normally a 1.6mm
to 3.2mm gap between the bolt pads
when installed.

90S - 90deg Elbow Light Duty

130S - Light Duty Tee
120 Elbow 45deg
300 Cap

Painted in acrylic enamel (MSDS

available).
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Available in Galvanised finish.
Galvanising conforms to ASTM A-153.
Also available Concentric Reducers,
Eccentric Reducers, Reducing Tees
and more.

1N - Flexible Coupling Light Duty

Accommodates pipe deflection and or

non-alignment: If nominal diameter
<DN200, deflection angle is >10; if
nominal diameter >DN200, deflection
angle is >0.50 but <10.
The C-shaped rubber gasket provides
excellent self-sealing capabilities in
both low and high-pressure services
as well as under certain vacuum
conditions.
The design and construction of the
coupling with elastomeric gaskets can
provide significant noise and vibration
absorption as well as seismic stress.
Coupling keys engage the full
circumference of the grooves and
provide significant pressure and end
load restraint against pipe movement
from internal and external forces.

3G Mechanical Tee Grooved

3J Mechanical Tee Threaded

Designed for creating an easy and

effective branch/outlet in pipe work.
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Available in Galvanised finish.
Galvanising conforms to ASTM A-153.
Available with threaded or grooved
outlets.

1G - Rigid Coupling

Can be used in services up to

3450Kpa and is available in painted
or hot dipped galvanised.
The built-in teeth on the coupling
grip the groove shoulder and serve
to reduce linear movement.
The T&G mechanism features a slight
offset at the foot of the coupling
halves which serve to protect the
gasket from exposure.
With the T&G style coupling no
metal-to-metal contact of the pads is
required. There is normally a 1.6mm
to 3.2mm gap between the bolt pads
when installed.

321G - Flange Adaptor Stub

Holes are incorporated into the

fitting, available in different hole
configurations.
Painted in acrylic enamel (MSDS
available).
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Available in Galvanised. Galvanising
conforms to ASTM A-153.

39

Roll Grooved System - Couplings & Fittings

Z07-Rigid Coupling Heavy Duty

Angle-pad design standard rigid

coupling for general piping applications
where rigidity is required.
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Also
available
in
Galvanised.
Galvanising conforms to ASTM A-153.

XH-70EP- Rigid Coupling Extra Heavy

The wider housing keys grip the grooves

with the aid of heavy duty bolts and
nuts for high pressure services.
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Housings are designed to be
incorporated with the specially
engineered EP cut-grooves on the pipe
(enquire for details).
Painted in green enamel.

40

7707 Flexible Coupling Heavy Duty

Features flexibility that can deal with

misalignment, distortion, thermal
stress, vibration and noise and also
resist seismic tremors.
Designed for use in a variety of general
piping applications of moderate or
high-pressure services.
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Available in Galvanised. Galvanising
conforms to ASTM A-153.

7041 Flange Adaptor Hinged Type

This fitting allows quick and direct

connection to PN10 or PN16 flanges.
The specially designed gasket enables
the transition from a grooved system
to a flanged system in one fitting.
Made to ASTM A-536 - Specification
for Ductile Iron Castings Grade.
Available in Galvanised. Galvanising
conforms to ASTM A-153.

Heavy Duty Fittings

7110 90deg Elbow
7111 45deg Elbow
7150 Concentric Reducer
7120 Equal Tee
7160 Cap

Painted in acrylic enamel (MSDS available).

Pressure rating conforms to the coupling and/ or pipe
that is being used.
Available in Galvanised. Galvanising conforms to
ASTM A-153.

Roll Grooved System - Valves

Butterfly Valve SJ-300N Lever & Gear Type

Check Valve Model SJ-915

The valve consists of epoxy coated ductile iron

body and EPDM or Nitrile rubber encapsulated
dual-seal disc.
Available in 10 position lever handle or a worm
gear operator.
Sizes 50mm-600mm.

Grooved-end dual-plate check valve designed

to provide positive and silent protection against
backflow in piping systems.
Sizes 65mm 600mm.

Suction Diffuser Model 725G

Check Valve Model SJ-900

Installed in the inlet side of a pump

that gives significant space saving
capability. Also features an integrated
strainer with easy access.
Sizes 65mm 400mm.

Features a spring-loaded wideopen clapper and non-stick

tight EPDM rubber seal. Can
be installed in the vertical or
horizontal position.
Sizes 65mm 600mm.

Y-Strainer Model 726

Straight flow design to remove

debris with lower pressure drop.
The stainless steel screen is easily
accessible by removing a single
coupling.
Sizes 50mm 400mm.

FIRE VALVES
Monitored Butterfly Valve Model
BB-G - Fire

Specifically used for indoor use only

for fire services. Installed with a UL
Approved Dual Tamper Switch.
Sizes 50mm 65mm.

Monitored Butterfly Valve

Model BO-G300 Fire

Fire service butterfly valve

that has a factory installed UL
approved tampered switch for
indoor and outdoor use.
Sizes 65mm 200mm.

Check Valve Model

DCG-300 Fire

The clapper design provides low

pressure drop in a compact body.
Ductile Iron body with EPDM
encapsulated disc.
Sizes 50mm 200mm.

41