Alarmes (B896)
Alarmes (B896)
Alarmes (B896)
AC MOTOR
CONTROLLER
MPE080-F [B890];
MPE060-F [B896];
AC Motor Controller
742.(a)52.(b)126.1le
General
General
This section describes the Iskra motor controller
and dash display used in MPE060-F, MPE080-F,
Description
Description
ELECTRICAL SYSTEM
The Iskra AC motor controller controls the AC traction
AC Traction Motor
The AC traction motor is a three-phase AC induction
motor. The motor does not include motor brushes
or a commutator. An AC induction motor operates
on three-phase AC power provided directly by the
controller. The motor speed is controlled by the motor
controller and can be changed by the frequency of the
AC power supplied to the motor. A speed sensor has
been built into one of the motor bearings which pro-
Parameters
Parameter Description
Parameter Description
PARAMETERS
Troubleshooting
Pick Deceleration
This parameter controls the rate of deceleration when
Troubleshooting
Troubleshooting
Description
To troubleshoot symptoms that do not generate a fault code, refer to Non-Status Code
Errors, in this section.
Troubleshooting
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
Check
Battery
Check Battery
LED
CIRCUIT
R0M0128 77 6
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
Overheat
(cont)
Overheat
Flashing Red
Traction Motor
DESCRIPTION
Controller has detected an over temperature
SYMPTOM
Troubleshooting
Troubleshooting
TroubleT
Troubleshooting
STATUS
CODE
Reset
Handle
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
Troubleshooting
STATUS
CODE
Troubleshooting
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
12814
Service Required
Solid Red
Steer Handle
DESCRIPTION
Controller has detected a belly switch error.
SYMPTOM
Troubleshooting
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
12832
Check Battery
Flashing Red
Battery
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
12835
Check Battery
LED
CIRCUIT
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
STATUS
CODE
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
STATUS
CODE
Troubleshooting
DISPLAY MESSAGE
LED
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
17170
Service Required
Solid Red
Traction Motor
DESCRIPTION
Controller has detected a failure of the traction
SYMPTOM
Troubleshooting
STATUS
CODE
Troubleshooting
STATUS
CODE
STATUS
CODE
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
STATUS
CODE
21379
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
TroubleshootingLED
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
21552
Improper Start
LED
CIRCUIT
Troubleshooting
Troubleshooting
Troubleshooting
STATUS
CODE
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
STATUS
CODE
Troubleshooting
STATUS
CODE
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
-
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
28961
Service Required
Flashing Red
Power Steering
DESCRIPTION
Stall Condition
SYMPTOM
Troubleshooting
STATUS
CODE
Troubleshooting
Troubleshoous.8791342 s200
rYRM
r1 s286
Troubleshooting
Troubleshooting
Troubleshooting
STATUS
CODE
33033
(cont)
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
STATUSCODE
STATUS
CODE
33034
Troubleshooting
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
STATUS
CODE
Troubleshooting
DISPLAY MESSAGE
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
33035
(cont)
Solid Red
Power Steering
DESCRIPTION
Controller cannot establish communication
with EPAS.
SYMPTOM
Troubleshooting
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
33057
(cont)
Service Required
Solid Red
CIRCUIT
Troubleshooting
STATUS
CODE
DISPLAY MESSAGE
LED
CIRCUIT
33073
Service Required
Solid Red
Power Steering
DESCRIPTION
SYMPTOM
Troubleshooting
Troubleshooting
STATUS
CODE
Troubleshooting
Electrical Checks
Electrical Checks
GENERAL ELECTRICAL SYSTEM
CHECKS
1. Turn the key to the OFF position, disconnect the
battery, and discharge the capacitors (refer to Dis-
Electrical Checks
and B+ at
(4)
(5)
(6)
(7)
WT wire (traTD -0
T T6d(8
8(i)-8.2()-11.4()9 71
c74e-0.6(r)6. 1 Tf 2.11.
da [( 74e-0.6(5(t)a
Dash Display
Belly Switch and pin 5 of JP1. If no continuity is found, replace control card.
g. SNAIL/TILLER ARM SW wire # wire W355 AC
(1)
(2)
Dash Display
Dash Display
Connector Pin-Outs
Connector Pin-Outs
110
Wire Number
Function
NOTES
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________