OUTDOOR NAVIGATION

A tutorial for hunters

Welcome to the Outdoor Navigation tutorial

This tutorial will provide you with knowledge of map reading
and the use of a compass and GPS.
The tutorial was developed in line with the recommendations of the review
of the risk assessment for hunting on State forests and Crown lands.
This tutorial must be completed before you are able to access the online
booking system to book a hunt on a State forest.
You will not be required to complete the assessment phase of this tutorial
again it is a once-only process.

Outdoor Navigation
Learning Outcomes:
Section 1: Map reading
Reading a topographical map
Reading a grid reference from a map
Section 2: The compass
Knowledge of the adjustable dial compass
Using the map and compass together
Section 3: GPS
Knowing how a GPS works
Knowing how to use the map and the GPS together

The Tutorial and Assessment

It will take you approximately 45 minutes to complete this tutorial and the assessment.
Read and understand the tutorial thoroughly. You will be assessed on your knowledge of
the three sections through 4 multiple choice or true/false questions for each section. You
will need to answer 3 out of the 4 questions correctly in each section to pass this tutorial.
You will be able to return to the tutorial at any time during the assessment by clicking the
Save and Exit box at the bottom of the assessment page.
If you do not pass the tutorial on the first attempt, you will be granted two more attempts in
a 24-hour period. If you do not pass within the 24-hour period, you can then resit the
assessment on any day after that period.

Outdoor Navigation
Glossary of terms:
Global Positioning System (GPS) A satellite navigation system that
provides location information anywhere on earth.
Topographical Map A relief map showing natural and man-made features.
Adjustable Dial Compass A compass which has an adjustable dial to
enable it to be orientated to a map.

Outdoor Navigation
Introduction
The skill of outdoor navigation is knowing where you are, where you want to go
and how to get there. Reading a map, using a map and compass together, and
using a GPS to navigate, are important skills to have when hunting.
The practice of looking at features on the map and identifying the same features
on the ground is, to a large extent, being replaced by the use of GPS, BUT the
GPS should never be relied upon as the only means of navigation and it should
never replace the skills of reading a map and using a compass to navigate.

Map Reading
A topographical map is an exact
replication of what is physically on
the ground.
The topographical map is ideal for
navigating in the bush as it shows
natural features such as hills,
valleys, high points, rivers, lakes
and vegetation types as well as
man-made features like buildings
and bridges.

Section 1

The Map Legend

There is a map legend on the
border of the topographical map
where symbols represent physical
features on the ground.
Symbols are represented in
different colours. Blue represents
water features, green is for
vegetation and black is for manmade features

True, Magnetic and Grid North

There are three different Norths and it is
important to know what they are when using a
map and compass:
True North is the direction toward the Earths
geographic north (the North Pole)
Magnetic North is the direction the magnetic
swinging compass needle points to (is located
in northern Canada)
Grid North is the direction of the vertical grid
lines on a topographical map

Contour Lines
A topographical map has contour lines that
show height. Contour lines represent relief
and show valleys, ridges and high points.
The distance in altitude between each
contour line varies depending on the map
you are using.
Contour lines that are close together
represent steep terrain, and lines that are far
apart represent slopes.

Relief Shading
Relief shading looks like a shadow
on south-east faces. The shadow
helps you visualise terrain and see a
3D effect.
Light shading represents easy
slopes and heavy shading
represents steep slopes.

Map Datum
Mapping and coordinate systems are based on a map datum
which is a mathematical surface that best fits the shape of the
earth.
The Australian map datum is called Geocentric Datum of Australia 1994 (GDA94).
GDA94 was introduced due to the increased use in GPS, which is based on the
World Geocentric System 1984 (WGS84).
The difference between GDA94 and WGS84 is less than a metre and therefore, for
most practical purposes, is the same.

Map coordinates are given as easting and

northing values and are in metres.
Eastings are vertical grid lines which run
north to south and northings are
horizontal grid lines which run west to
east on the face of a topographical map.
Each easting and northing is numbered
on the map. These numbers are used to
find a grid reference.

Easting Grid Line

Map Coordinates
Northing Grid Line

Grid References
A grid reference is used to identify a
position on a topographical map.
Easting and northing grid lines form
grid squares. Each easting grid line
is numbered west to east and
northing numbered south to north.
Each easting and northing is
numbered on the map. These
numbers are used to find a grid
reference.

Grid square

Find a six figure grid reference

Remember: to read across the map and then up

the map walk before you climb.

Grid Square

Easting Grid Line

Find the grid reference for Mt Cuvier by

identifying the grid square where Mt Cuvier sits
in. Read the two figure easting value then
estimate the tenths from the easting grid line
toward the east. The first three figures of the grid
reference are 192. Then estimate the tenths from
the northing grid line toward the north. The final
three figures of the grid reference are 467. The
six figure grid reference for Mt Cuvier is 192467.

Northing Grid Line

Navigating from a topographical map

Navigating using a topographical map requires route planning. The easiest route
is not always the shortest distance. Walking in rough terrain is difficult and will
more likely increase the time to travel the distance. Knowing how to read a
topographical map enables you to see features on the map and then identify the
corresponding features on the ground or vice versa. These features might include
stream junctions, a rock bluff, a change in vegetation or a high point. Travelling
using a topographical map is done by recognising features on the ground and then
following them on the map or identifying features on the map and following them
on the ground. If you see features on the map you should expect to find them on
the ground as you travel.

Navigating by following handrails

Handrails are features that are easily identified on
the map and on the ground such as streams,
ridges, bush edges, tracks or fence lines. Plan
your route to follow handrails and use these to
stay on your route. In steeper terrain it is better
to use ridges and spurs as hand rails rather than
streams which can be steep and difficult to
navigate.
The planned route on the map uses a creek, river
and spur as a handrail.

Assessment for Section 1

You have now completed section 1 for:
reading a topographical map
reading a grid reference from a map
You can now go on to completing the assessment for section 1 by
clicking on the assessment box below.
You will be able to go back to the tutorial for further reading at any
time during the assessment.

The Adjustable Dial Compass

Base plate: Transparent plate with a straight edge parallel

with the direction of travel arrow
Direction of travel arrow: This arrow is used to indicate
the direction of travel
Orienting arrow: This arrow is used to orientate your
compass to the map
Orienting lines: These lines are parallel with the orienting
arrow and assist with orientating the compass to the map
Magnetic needle: Points to magnetic north
Adjustable dial: Enables you to orientate the compass to
the map and show a bearing in degrees
Index line: Enables you to read a bearing for a direction of
travel

Section 2

Direction of Travel Arrow

Index Line
Magnetic
Needle
Orienting
Arrow
Orienting Lines
Base plate

Adjustable Dial

Bearings
A compass bearing is an actual direction
expressed in cardinal points or degrees.
Cardinal points are shown on the dial of
a compass as North (N), South (S), East
(E) and West (W), Northwest (NW) and
North Northwest (NNW), along with all
other corresponding cardinal points on
the compass dial.
Degrees are shown on the compass dial
from 0 to 360.

Magnetic Variation
Magnetic variation, sometimes also
known as magnetic declination, is the
difference in degrees between grid north
and magnetic north.
Magnetic variation differs depending on
where you are on the Earths surface
and changes over time.
The relevant magnetic variation
information can be found on the border
of the topographical map you are using.

You will need to know the magnetic

variation to gain a direction of travel
by using a map and compass
together.

Gaining a direction of travel by using a

map and compass together
There are four steps that will enable you to gain a
direction of travel by using a map and compass together.
STEP 1
You are at point A and want to travel to point B
Place the long edge of the base plate on A and B
with the direction of travel arrow pointing in the
same direction as point B

Gaining a direction of travel by using a

map and compass together
There are four steps that will enable you to gain a
direction of travel by using a map and compass together.
STEP 2
Turn the adjustable dial until the orienting lines are
parallel with the North South grid lines and the
orienting arrow is pointing to Grid North.

Grid North

Orienting Lines

Now take the compass off the map (Take care not to
move the dial).

Gaining a direction of travel by using a

map and compass together
Grid
Bearing

STEP 3
Note the grid bearing from the adjustable
dial and index line (70).

Subtract the variation (as indicated on

the map border), for example, 10, from
the grid bearing by moving the adjustable
dial so that the subtracted figure aligns
with the index line (60).

Index Line
Magnetic
Bearing

Gaining a direction of travel by using a

map and compass together
STEP 4
Hold the compass horizontally in front of
you with the direction of travel arrow
pointing away from you. Turn yourself
around until the magnetic needle points
to NORTH on the adjustable dial. The
direction of travel arrow now points to
where you want to go (point B)

Assessment for Section 2

You have now completed section 2 for:
knowledge of the adjustable dial compass
using a map and compass together
You can now go on to completing the assessment for section 2 by
clicking on the assessment box below.
You will be able to go back to the tutorial for further reading at any
time during the assessment.

How does a GPS work?

The GPS works by receiving signals from
at least three, but preferably four, of the
30 GPS satellites orbiting the Earth.
Signals from several satellites create a
trilateration. Trilateration is a
measurement of a series of distances
that lets you know where you are on
Earth by giving you a set of coordinates
on your GPS.

Section 3

Use a GPS to find your position on a map

Use a GPS that is set up with datum WGS84 and
use a GDA94 topographical map. Turn the GPS on
and acquire coordinates (grid reference). Your
position will be shown as a 14 digit reference; the
first 7 numbers will be the easting and the last 7
numbers the northing. To obtain a six figure grid
reference from these coordinates read the middle
three numbers from the easting and the middle three
numbers from the northing. E.g. easting 0601366
and northing 6019907. Your six figure grid reference
is 013199. You can now find your position on the
map using the grid coordinates on the map border.

Other basic functions of the GPS

Your GPS user manual describes in detail all other
functions of the GPS. Marking a waypoint will
enable you to use your GPS to return to your camp
or vehicle. You can mark a waypoint by either
entering a grid reference from the map or enter the
waypoint by pressing the mark button on the GPS
which will mark the GPSs current position. The
GPSs compass will give you the direction you need
to travel to arrive at your waypoint. Most GPSs have
a tracking function that will log the route you
travelled. The GPS must be turned on and receiving
satellite signals to log your track.

The compass in your GPS

Most recent models of GPS have an electronic
compass that will give your direction of travel while
you are standing still. The compass of older models
required you to be moving as it worked by the
satellites tracking the direction you were walking.
The electronic compass will need periodic calibration
and the GPS will prompt you when this is required.
Calibrating the compass is simply a matter of
holding the GPS horizontal and following the onscreen instructions to rotate slowly around three
times.

Things to be wary of when using a GPS

Beware that the GPS will not work if the batteries go flat. Always ensure you take spare
batteries with you.
Acquiring a position and coordinates under thick bush canopies, especially when the
canopy is wet from rain, can be difficult. You may need to move to a more open area.
Deep valleys may restrict the availability of satellites as they will be obscured by the hills.
You may need to climb part way out of the valley to acquire a position.
Satellites continually move across the sky as the Earth rotates and at times there may not
be enough satellites visible to your GPS for your GPS to acquire a position. The situation
will change as more satellites pass within range of your GPS.
Do not rely on your GPS as your sole navigation tool. They can break down. Always take
a map and compass.

Assessment for Section 3

You have now completed section 3 for:
knowing how a GPS works
how to use a GPS and map together
You can now go on to completing the assessment for section 3 by
clicking on the assessment box below.
You will be able to go back to the tutorial for further reading at any
time during the assessment.