Manual 12 en Piles Introduction

Engineering manual No.
12
Updated: 04/2016
Pile Foundations Introduction

The objective of this engineering manual is to explain the practical use of programs for the
analysis of pile foundations in GEO 5.
GEO 5 software contains three pile foundation analysis programs Pile, Pile CPT and Pile Group.
The text below contains a closer explanation of which of the programs are to be used under
particular conditions individual programs are subsequently described in following chapters.
Vertical load-bearing capacity of pile foundations is determined by various methods:
by a static pile test: these tests are required in some countries and a structural analysis
functions only as a preliminary pile foundation proposal;
by an analysis based on soil shear strength parameters: using analysis methods NAVFAC
DM 7.2, Tomlinson, CSN 73 1002 and Effective stress in programs PILE and PILE GROUP;
by an analysis based on the assessment of penetration tests: PILE CPT program;
by an analysis according to regression curves equations obtained from the results of

static loading tests (according to Masopust): PILE program; Vertical load-bearing capacity
is determined from the pile loading curve for corresponding (allowable) settlement (CSN
73 1002 standard specifies the corresponding settlement value slim 25.0 mm ).
by an analysis based on Mohr-Coulomb parameters and stress-strain properties of soils:

using the so-called Spring Method in PILE and PILE GROUP programs;
by numerical analysis using the Finite Element Method: the FEM program.
From this list it follows that piles can be assessed using many ways and on the basis of different
input parameters. It means that analysis results can be identical, but often they can significantly
differ.
The great advantage of GEO 5 is the fact that the user can try more variants and analysis methods,
find the most likely behaviour of the pile foundation and subsequently determine the total bearing
capacity or settlement of a single pile or a pile group.
The vertical load-bearing capacity of pile foundations is assessed in GEO 5 programs (with the only
exception: Pile Group Spring Method) only for vertical normal force acting on the foundation. The
horizontal forces acting on the foundation, bending and torsional moments have no influence
on the analysis of the vertical load-bearing capacity of piles.
The procedure of the vertical load-bearing capacity of a single pile analysis in GEO 5 PILE is
presented in Chapters 13 and 14, whilst the analysis for the same pile on the basis of CPT tests is
described in Chapter 15.
Horizontal bearing capacity of pile foundations:

The result of the analysis for a horizontally loaded pile is the horizontal deformation of the pile
and the curve for internal forces along the pile shaft.
In the case of a single pile, its horizontal deformation and reinforcement depend on the calculated
modulus of horizontal reaction of the sub-soil and the loading by the lateral force or the bending
moment. The analysis procedure is explained in Chapter 16. The analysis for a pile group is presented
in Chapter 18.
Settlement of pile foundations:

The actual load-bearing capacity of a pile is directly associated with its settlement because of the
fact that virtually any pile settles under the action of loading and gets vertically deformed.
The settlement of single piles is determined in the PILE program by the following methods:
according to Masopust (non-linear): the program analyses the settlement of a single pile
on the basis of the regression coefficients along the skin and under the base of the pile.
according to Poulos (linear): the program analyses the value of the total settlement
on the basis of the determined pile base bearing capacity Rb and the pile skin bearing
capacity Rs .
2
by means of the Spring Method: the program analyses the loading curve on the basis
of set parameters of soils using the Finite Element Method.
The PILE program constructs the loading curve (the so-called working diagram) for all
of the methods.
The settlement of a pile group is described in Chapter 17, the settlement of piles designed on the
basis of penetration tests CPT is presented in Chapter 15.
Program selection
1. the decision according to the stiffness of the base slab (pile cap). When the pile cap
is considered to be infinitely stiff, the Pile Group solution is used. In other cases
we investigate single piles.
2. the decision according the results of a geological survey. If the results of CPT tests
are available, the Pile CPT program is used for the analysis of the single pile or the pile
group (see Chapter 15). In other cases the program Pile (or Pile Group) is used for the
solution, on the basis of the set soil parameters.
Based on the type of the analysis we distinguish:
analysis for drained conditions: effective parameters of shear strength of soils ef , cef are
used in the Pile and Pile Group programs as a standard for analysis methods CSN 73 1002
and Effective stress;
3
analysis for undrained conditions: only the value of the total soil cohesion cu is set in the
Pile and Pile Group programs. The vertical load-bearing capacity of a single pile is
determined according to Tomlinson, whilst a pile group is analysed as the load-bearing
capacity of a soil cylinder (block) according to the FHWA.
The NAVFAC DM 7.2 method combines both of the aforementioned analysis procedures. It is
possible to choose whether each of the soil layers is considered drained (cohesionless) or undrained
(cohesive).
General specification of the problem:

Analyse the vertical load-bearing capacity and settlement of a pile foundation (see the Chart)
in the set geological profile; further determine the horizontal deformation of the piles and propose
reinforcement for individual piles. The pile foundation consists of four bored piles with diameter
d 1.0 m and length l 12.0 m . The resultant force of the total loading N , M y , H x acts at the
level of the upper surface of the foundation slab (pile cap) namely in the slab centre. C 20/25
reinforced concrete is used for the piles.
Loads acting on piles

To simplify the problem, we will always consider 1 loading case in the program.
The determination of loads acting on the pile foundation is different depending on the structure
type and subsequent solution, i.e. whether we solve a single pile or a pile group.
Pile Group
We assume that the slab joining the piles is stiff. In our case we will consider a pile cap with
thickness t 1.0 m . In this case we determine the total reaction in the pile cap centre.
Note: A simple method of obtaining loads on a pile group using any of the static programs
is described in the Help for the Pile Group program Determination of loading on a pile group.
a) Design (calculation) loads:
Vertical normal force:
N 5680 kN ,
Bending moment:
M y 480 kNm ,
Horizontal force
H x 310 kN .
4
b) Imposed (working) loads:
N 4000 kN ,
Bending moment:
M y 320 kNm ,
Horizontal force:
H x 240 kN .
Problem specification chart pile foundation
Single piles
If the slab is soft in bending (non-stiff) or the building is founded on a pile cap, the structural
diagram is different and we will obtain reactions at the heads of individual piles from a static
program (e.g. GEO 5 Plate, FIN 3D, SCIA Engineer, Dlubal RStab etc.).
5
In this example we will carry out the pile analysis using only 1 loading case for simplification.
a) Design loading:
N1 1450 kN ,
Bending moment:
M y ,1 120 kNm ,
Horizontal force:
H x ,1 85 kN .
b) Service loading:
N1 1015 kN ,
Bending moment:
M y ,1 80 kNm ,
Horizontal force:
H x ,1 60 kN .
Loads action chart distribution of loading among individual single piles
Note: If we assume identical dimensions and reinforcement of the piles, we can assess all piles
as one pile, but with loading combinations acting on all piles.
Geological profile
0.0 to 6.0 m:
Sandy Clay (CS, consistency firm),
down from 6,0 m:
Sand with trace of fines (S-F, medium dense soil).
Note: The basic soil parameters are the same as for the calculation of single piles
and for the verification of the pile group. Their values are given in the following table.
Sandy Clay (CS)

consistency firm
Soil parameters / Classification
Unit weight kN m 3
Sand with trace

of fines (S-F)
medium dense soil
18,5
17,5
20,5
19,5
14,0 / 50,0
0/0
Angle of internal friction ef
24,5
29,5
Adhesion factor
0,6
Bearing capacity coefficient p
0,3
0,45
Poissons ratio
0,35
0,3
Oedometric modulus Eoed MPa
8,0
21,0
Deformation modulus E def MPa
5,0
15,5
Clay
(cohesive soil)
Sand, gravel
(cohesionless soil)
10,0
15,0
60,0
150,0
4,5
5,0
15,5
Unit weight of satur. soil sat kN m 3
Cohesion of soil c ef / cu kPa
Type of soil
Angle of dispersion
Coefficient k MN m 3
Modulus of horizont. comp. n h MN m 3
Modulus of elasticity E MPa
Table with the soil parameters pile foundations (summary)
List of chapters related to pile foundations:
Chapter 12:
Pile foundations
Chapter 13:
Analysis of vertical load-bearing capacity of a single pile
Chapter 14:
Analysis of single pile settlement
Chapter 15:
CPT tests based pile analysis
Chapter 16:
Analysis of horizontal load-bearing capacity of a single pile
Chapter 17:
Analysis of vertical load-bearing capacity and settlement of a pile group
Chapter 18:
Analysis of deformation and pile group dimensioning.

Manual 12 en Piles Introduction

Uploaded by

Copyright:

Available Formats

Manual 12 en Piles Introduction

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual 12 en Piles Introduction

Uploaded by

Copyright:

Available Formats

Engineering manual No.

Pile Foundations Introduction

Vertical load-bearing capacity of pile foundations is determined by various methods:

by an analysis based on the assessment of penetration tests: PILE CPT program;

by an analysis according to regression curves equations obtained from the results of

by an analysis based on Mohr-Coulomb parameters and stress-strain properties of soils:

Horizontal bearing capacity of pile foundations:

Settlement of pile foundations:

Based on the type of the analysis we distinguish:

General specification of the problem:

Loads acting on piles

a) Design (calculation) loads:

Vertical normal force:

b) Imposed (working) loads:

Vertical normal force:

Problem specification chart pile foundation

Vertical normal force:

Vertical normal force:

Loads action chart distribution of loading among individual single piles

Sandy Clay (CS, consistency firm),

down from 6,0 m:

Sand with trace of fines (S-F, medium dense soil).

Sandy Clay (CS)

Soil parameters / Classification

Sand with trace

Angle of internal friction ef

Bearing capacity coefficient p

Oedometric modulus Eoed MPa

Deformation modulus E def MPa

Unit weight of satur. soil sat kN m 3

Cohesion of soil c ef / cu kPa

Modulus of horizont. comp. n h MN m 3

Modulus of elasticity E MPa

Table with the soil parameters pile foundations (summary)

List of chapters related to pile foundations:

Analysis of vertical load-bearing capacity of a single pile

Analysis of single pile settlement

CPT tests based pile analysis

Analysis of horizontal load-bearing capacity of a single pile

Analysis of vertical load-bearing capacity and settlement of a pile group

Analysis of deformation and pile group dimensioning.

You might also like