264869621

SUNFAR C320 1
C320 series of Inverter

Sensorless Vector
Manual
SHENZHEN SUNFAR ELECTRIC TECHNOLOGIES CO.,LTD
C320 Series of Sensorless Vector Inverter Operation Manual
SUNFAR C320
PREFACE
Thank you very much for choosing C320 series of sensorless vector inverter.
This manual provides guidance of using the inverter safely and carefully, containing
introduction of installation, wiring, parameter list, routine maintenance, operating rules and
cautions, etc.
In order to make good use of the inverter properly and safely, please read this manual
thoroughly before using. It may lead to abnormal operation and failure, reduce using life, even
damage the equipment and cause personal injury if you use it wrongly.
This manual is attachment together with the inverter. Please keep it well and it would be
available to engineering and installation personnel, repairing and maintaining during the
product functioning period. SUNFAR has the right to modify and ameliorate products, data
and dimensions without notice, so this manual is updated and all the contents in this manual
are subject to change without any notice.
SHENZHEN SUNFAR ELECTRIC TECHNOLOGIES CO., Ltd.
SUNFAR C320 3
Table of Contents
6
1 INTRODUCTION
6
5
6
1.1 Model explanation 6

6
1.2 Appearance description 6
6
7
1.3 Model of inverter
7
9
1.4 Specifications8
9
11
INSTALLATION GUIDELINES
11
10
11
2.1 Environmental requirements 10
11
11
2.2 Disassembly and assembly of the panel
11
10
12
2.3 Disassembly and assembly of the cover board 12
11
13
2.4 Dimension of inverter
13
12
WIRING PROCEDURE 16
16
15
16
3.1 Precautions
16
15
17
3.2 Wiring of external components
17
15
19
3.3 Basic wiring
19
17
21
3.4 Terminal of main circuit 18
21
3.5 Terminal of Control circuit 21
21
19
23
OPERATIONS OF INVERTER AND SIMPLE RUNNING21
23
23
4.1 Operation panel
23
21
24
4.2 Basic function of panel and methods of operation22
24
27
4.3 List of state monitor parameter
27
25
28
4.4 Simple operation
28
26
29
PARAMETERS LIST 27
29
DESCRIPTION OF SPECIFIC FUNCTIONS 44
44
39
6.1 Basic operation parameter unit 44
44
39
6.2 Primary application of parameter unit 49
49
43
54
6.3 Analog I/O parameter unit
54
48
57
6.4 Digital O/I parameter unit
57
51
62
6.5 Auxiliary running parameter unit
62
55
67
6.6 Multi-speed running parameter unit 60
67
70
6.7 Advanced running parameter unit 62
70
72
6.8 Wobble freq. running parameter unit 65
72
6.9 PID control parameter unit 66
6.10 Communication function parameter units
69
6.11 Special function parameter unit
69
7 FAULT DIAGNOSIS AND COUNTERMEASURES 72

7.1 Protective functions and countermeasures 72
7.2 Fault record inquiry
73
SUNFAR C320
7.3 Reset 74
8 MAINTENANCE 75
8.1 Daily Maintenance 75
8.2 Damageable parts maintenance 76
8.3 Storage
76
8.4 After sale services76
9 USAGE EXAMPLE 77
9.1 Panel on-off control, Panel potentiometer setting frequency77
9.2 External on-off control mode, external voltage setting frequency
77
9.3 Multi-speed running, external on-off control mode 78
9.4 Panel on-off controlPanel potentiometer setting
frequency and linkage control with inverters 78
Appendix RS485 COMMUNICATION PROTOCOL

80
Appendix II OPTIONS 89
1.
Operation panel
89
2.
Brake resistance 90
SUNFAR C320 5
PRECAUTIONS
In order to use the inverter properly and safely, please read this manual carefully before using. And you
should follow the requirements of this manual to move, install, run, operate and repair the inverter.
1. Opening
Please check any damage that may have occurred during transportation.
Please check whether the nameplate data of inverter is in accordance with your order, if anything wrong,
please contact supplier immediately.
Our product is manufactured, packed and transported in the strict quality system. But in case there is any
error, please contact with our company or local agent, we will solve the problem as quickly as possible.
z
Inverters nameplate data

C320-4T0015
Inverter's model
SOURCE:
3PH 380V 50/60Hz
Rated Parameters
OUTPUT:
2.4KVA 3.7A
Rated output capacity and current
0123456789
Product series No.
TYPE:
SERIAL No.:
Bar code
Fig-1 Nameplate
2. Safety regulations
There are four kinds of symbols being related with cautions as follows:
Danger: If user does not operate
according to requirements, it will lead to
death, grievous bodily harm or severe
property loss.
Warning: If user does not operate

according to requirements, it will lead
to injury or damage of inverter.
This symbol will hint some useful

information.
This symbol will hint some items that

need to be noticed in operation.
2.1 Installing
2.1.1.
2.1.2.
2.1.3.
Do not put the inverter on the combustible material.

C320series inverter cant install in the explosive ambient.
Do not drop other material into the inverter.
It is forbidden to disassemble and refit the inverter.
2.2 Wiring
2.2.1.
2.2.2.
2.2.3.
2.2.4.
2.2.5.
It must be operated by professional worker when wiring.

Please be sure to turn off the power supply at least 10 min before wiring.
Inverter and motor must be grounded correctly.
Be sure to wire or inspect the inverter after power-off at least10 minutes.
Electron components are sensitive about static electricity, so do not drop other material in inverter or
touch the main circuit.
SUNFAR C320
It is forbidden to connect an AC power supply with the U, V and W output terminals directly
2.3 Maintenance
1.
2.
Do not touch the radiator after power-off at least 10 minutes.

The earth terminal of inverter must be connected to ground reliably.
3. Attention Notes:
3.1.
3.2.
3.3.
3.4.
Be sure to install the inverter in a well-ventilated ambient.

The temperature at variable-frequency will be higher than at line-frequency, which is normal
phenomenon.
The ordinary motor cannot run in the low speed for a long time, so user should select the special
motor for inverter or reduce the motor load under the low speed.
When the altitude is over 1000m, the inverter will be valid to decrease the rated current, and the
rated current will decrease 10% when the attitude is increased 1500m.
Be sure not to connect the output terminals of inverter with the filter capacitors and other surge absorbers.
4 Dispose:
When you dispose inverter and its parts, please pay attention to:
Capacitor: The capacitors in inverter may explode when they are burned.
Plastic: Poisonous gas may be generated when the front panel is burned, please pay attention to the waste
gas when the plastic parts are burned.
Method: Please dispose inverter as industry rubbish.
SUNFAR C320 7
1.
INTRODUCTION
1.1 Model explanation

C320 - 4 T 0037
Product
0015
0022
0037
.
.
.
2800
3150
Sensorless
C320
Vector
Drive
Voltage Class
2
4
Applied Motor
capacityKW
1.5
2.2
3.7
.
.
.
280
315
Power supply
220V
380V
T
S
3-phase
1-phase
1.2 Appearance description

1.2.1 Appearance of model I
Panel interface
Remote line interface
Operation panel
Upper cover
Control circuit terminals
Cable inlet of control circuit
Main circuit terminals
Cable inlet of mian circuit
Mounting hole
It is fit for C320-2S0015C320-2S0037/ C320-4T0015C320-4T0075/C320-2T0015C320-2T0037.

1.2.2 Appearance of model II
C320
Operation panel
Upper cover
WARNING
1.Refer to the instruction manual before installation

and operation.
2.Do not connect AC power to output terminals UVW.
3.Do not remove any cover while applying power
and at least 10min. after disconnecting power.
4.Securely ground(earth) the equipment.
Lower cover
Control terminals
Main circuit terminals
It is fit forC320-4T0110C320-4T0750 / C320-2T0055C320-2T0450
SUNFAR C320
C320
Operation panel
Upper cover
Control terminals
WARNING
1.Refer to the instruction manual before installation and

operation.
3.Do not remove any cover while applying power and
at least 10min. after disconnecting power.
Lower cover
Main terminal
R S T
POWER
(+) (-)
U V W
MOTOR
It is fit for C320-4T0900C320-4T1100 / C320-2T0550

1.3 Model of Inverter
Model
General load (G-load) ([F0.15]=0)
Pump and fan load (P-load) ([F0.15]=1)
C320-2S0015
Rated Power
KVA
2.9
Rated output
currentA
7.5
Applied motor
Power (KW)
1.5
Rated power
KVA
--
Rated output
currentA
--
Applied Motor
Power (KW)
--
C320-2S0022
3.8
10
2.2
--
--
--
C320-2S0037
5.7
15
3.7
--
--
--
C320-2T0015
2.9
7.5
1.5
--
--
--
C320-2T0022
3.8
10
2.2
--
--
--
C320-2T0037
5.7
15
3.7
--
--
--
C320-2T0055
9.5
25
5.5
--
--
--
C320-2T0075
12.6
33
7.5
--
--
--
C320-2T0110
17.5
46
11
--
--
--
C320-2T0150
22.9
60
15
--
--
--
C320-2T0185
28.6
75
18.5
--
--
--
C320-2T0220
32.4
85
22
--
--
--
C320-2T0300
41.9
110
30
--
--
--
C320-2T0370
51.5
135
37
--
--
--
C320-2T0450
64.8
170
45
--
--
--
C320-2T0550
78.1
205
55
--
--
--
C320-4T0015
2.4
3.7
1.5
3.6
5.5
2.2
C320-4T0022
3.6
5.5
2.2
5.6
8.5
3.7
C320-4T0037
5.6
8.5
3.7
8.6
13
5.5
C320-4T0055
8.6
13
5.5
11
17
7.5
C320-4T0075
11
17
7.5
16.5
25
11
C320-4T0110
16.5
25
11
21.7
33
15
C320-4T0150
21.7
33
15
25.7
39
18.5
C320-4T0185
25.7
39
18.5
29.6
45
22
C320-4T0220
29.6
45
22
39.5
60
30
C320-4T0300
39.5
60
30
49.4
75
37
C320-4T0450
60
91
45
73.7
112
55
C320-4T0550
73.7
112
55
98.7
150
75
C320-4T0750
98.7
150
75
116
176
90
C320-4T0900
116
176
90
138
210
110
C320-4T1100
138
210
110
171
260
132
SUNFAR C320 9
General load (G-load) ([F0.15]=0)
Model
Pump and fan load (P-load) ([F0.15]=1)
Rated Power
KVA
Rated output
currentA
Applied motor
Power (KW)
Rated power
KVA
Rated output
currentA
Applied Motor
Power (KW)
C320-4T1320
171
260
132
204
310
160
C320-4T1600
204
310
160
237
360
185
C320-4T1850
237
360
185
253
385
200
C320-4T2000
253
385
200
276
420
220
C320-4T2200
276
420
220
313
475
250
C320-4T2500
313
475
250
352
535
280
C320-4T2800
352
535
280
395
600
315
C320-4T3150
295
600
315
424
645
350
1.4 Specifications
Three-phase4T****
Single-phase2S****
380V, 50/60Hz
220V 50/60Hz
Permissible voltage
Three-phase4T****
Single-phase2S****
fluctuation
320V ~ 460V
170V ~ 270V
Voltage
Three-phase (4T****) 0 ~380V
Single-phase (2S****) 0~220V
Frequency
0~400Hz
Rated Voltage and freq.

Input
Output
Over-loading Endurance
Control System
110% rated current for long-term 150% rated current for 1min
180% rated current for 2s
Sensorless current vector-control V/F control
Freq.
Analog Input
Control
Digital Input
0.01Hz
External pulse
0.1% of maximum freq.
Analog Input
Within 0.2% of maximum output freq.
Digital Input
Within 0.01% of setting freq.
External pulse
0.1% of maximum freq.
Resolution
Freq.
Precision
0.1% of maximum output freq.
Reference freq. can be discretionally set between 5 and 600Hz.

V/F curve
V/F control
Control
Torque boost
Automatic
current/voltage
Limiting
Characteristics
Sensorless
Current
vector control
And V/F curve with multi-mode can be discretionally set. There are also three
curves provided, Constant torque curve, Dec torque curve 1 and Dec torque
curve 2.
Manual torque boost can be set between 0 and 20 percent
Automatic torque boost can be set according to output current.
It will determine automatically the current and voltage of stator of motor, which
will be controlled within the allowable range.
Volt/Freq
characteristics
Automatically adjust the ration of voltage to frequency according to
Torque
While freq equals 1, the torque is 150% rated torque.

The lasting accuracy is 0.1%
characteristics
the parameter of motor and unique arithmetic.
Motors parameter
The motors parameter self-detection can finished in static state mode.
self-detection
Current / voltage
restraint
Under voltage inhibit

feature In running
Current close-circuit control can avoid the current attack.

It is especial for the users with lower power supply and voltage fluctuate
frequently, even the voltage is lower than Permissible voltage, and the system
will maintain the longer running time.
10
SUNFAR C320
Multi-speed selection
And Wobble freq. running
Embedded PID controller can preset freq. Standard positioning RS485

Manifold communication protocols can be selected, having synchronous
linkage function.
PID control
RS485 communication
Freq.
Analog input
DC voltage05 and 010VDC current 020mA
Pulse input
Its amplitude value is between 5 and 30V, and its freq. is within 50.0KHz (can
receive OC signal)
Digital input
It can be set by Operation panel, RS485, UP/DW terminal and combination

setting.
OC output
Two OC output, 16 options can be selected, faults electric delay out can be
selected (TA, TB and TC)
Analog output
Two output0~10V voltage, 0~20mA current, and upper/lower limit can be set
by user
Setting
Output Signal
Typical
Functions
Up to 8 stages of programmable multi-speed control, 6 kinds of running mode

Wobble freq. function is composed of preset freq., center freq. adjusted and
saving state and restart when inverter just had power off.
Automatic energy saving

running
Voltage stabilizing running
Automatically
Acceleration/deceleration
Time setting
Input voltage and compensation for speed drop is adjusted by real-time output
current.
To get the most stable running effect, user can select static stabilizing
voltage, dynamics stabilizing voltage and non-stabilizing voltage.
0.1 to 6000 seconds, S-curve or linear
Regenerative
braking
75% above
DC braking
Start and stop can be selected respectively, action freq. is form 0 to 50.0Hz,
and action time is form 1 to 20.0s. Continuous action is also optional.
Brake
Determine speed and restart
To use the function of Smooth restarting and stop restarting during motor
works.
Counter
Embedded one counter, which will help the integration of system
Operation functions
Setting of upper limit freq. and lower limit freq., freq hopping running,
Reversal running limit, slip freq. compensate, RS485 communication,
frequency Acc/Dec control, self-recovery running, etc
Operation Status
Out freq., Out current, Out voltage, Motor speed, Setting freq., Temperature
of Module, PID setting, Feedback value, Analog O/I, etc
Fault details
Recently six faults recorded, output freq., setting freq., output current,
output voltage, DC voltage and module temperature
Display
Protection/Warning Functions
Over current, over voltage, under current, under voltage, thermal relay,
overheating, Short circuit, out voltage would be short of the phase, The
parameters of motor is abnormal, Main contactor cant attract, Internal
memory faults, etc.
Ambient temperature:
-10~+50
Ambient humidity: under 90%

Environmental Conditions
Ambient atmosphere: indoors (non-corrosivenon-inflammablenon-oil,

non- fog etc.)
Altitude is lower than 1000m
Configuration
Installation
Enclosure rating is IP20

Cooling system is in the cooling mode.
Hanging
SUNFAR C320 11
2. INSTALLATION GUIDELINES
2.1 Environmental requirements:
1.
2.
3.
4.
5.
6.
7.
Be sure to install the inverter in a well-ventilated room.

Ambient temperature is from -10 to 40. If the temperature is 40 to 50, please take out the lower
cover to cool.
Please avoid putting the inverter in a high temperature and moist location. The humidity is less than 90%
and non-condensing.
Keep away from combustible, explosive material and caustic gas or liquid.
No dust, floating fiber and metal particles
The inverter must be installed in a firm and no vibration location.
The installation plane should be solid and not vibrant.
If users demand any special installation, please contract us firstly.

C320 series inverter is hanging model, so it should be in vertical way. In order to ensure the air circulation
around the inverter to aid in cooling, there should be enough space around the inverter shown as Fig. 2-1-A.
Add the air deflector when apply the up-down installation shown as Fig. 2-1-B.
Fan ventilation
Above 120mm
E380
Inverter
Air flow clapboard
Above 50mm
Above 50mm
WARNING
Inverter

and operation.
Above 120mm
Fig2-1-A Interval distance
Fig2-1-B Multi-inverter Installation
2.2 Disassembly and assembly of the panel

Disassembly
Put your middle finger into open hole. Then gently press the fixed spring on the top of panel. Then pull
outward to remove the panel.
Assembly
Aim the fixed hook to spring clip at bottom of operation panel, then press the fixed spring backward. Then
push inward to the certain place. Shown as Fig. 2-2.
12
SUNFAR C320
Panel base
Spring cilp
Fig.2-2Disassembly and assembly of the panel
2.3 Disassembly and assembly of the cover board

2.3.1 Disassembly and assembly of plastic cover board
It is fit forC320-4T0015C320-4T0075 / C320-2T0015C320-2T0037 / C320-2S0015C320-2S0037
Disassembly
Put the finger into the portable hole, pull upward to move the cover form the shell, then pull downward,
which will remove the cover board.
Assembly
Lift the bottom of cover up to about 15o, inserting the Fixed hook into the hold down groove, then press the
cover down to hear a sound of Click, which means the cover board has already been mounted and shown
as Fig. 2-3-A.
Fixed hook
Hole
Portable hole
Fig2-3-A
Disassembly and assembly of plastic cover board
2.3.2 Disassembly and assembly of lower cover board

It is fit forC320-4T0110C320-4T0750/ C320-2T0055C320-2T0450
Disassembly
1.
2.
Take two screws at bottom of lower cover board.

Move the lower cover board downward.
Assembly
1.
2.
3.
Put the lower cover board parallel with the interval.

Move the lower cover board upward.
Screw the bottom of lower cover board.
SUNFAR C320 13
80
E3
Fig.2-3--B Disassembly and assembly of lower cover
2.4 Dimension of inverter

2.4.1 Model
It is fit forC320-4T0015C320-4T0075 / C3202T0015C3202T0037 / C320-2S0015C320-2S0037.
W
W1
H H1
Fig2-4-A Dimension of model
2.4.2 Model
It is fit forC320-4T0110C320-4T0750/ C320-2T0055C320-2T0450.
W
W1
E 3 80
H1
WARNING

and operation.
Fig2-4-B Dimension of model
14
SUNFAR C320
2.4.3 Model
It is fit forC320-4T0900C320-4T2000/ C320-2T0900.
W
W1
D
E 3 80
H H1
!
WARNING
1.Refer to the instruction manual before installation and

operation.
3.Do not remove any cover while applying power and
at least 10min. after disconnecting power.
Fig 2-4-C Dimension of model III
2.4.4 Model IV
It is fit forC320-4T2200C320-4T2800.
W
W1
E380
H H1
WARNING

and operation.
Fig 2-4-D Dimension of model IV
Installation dimension of inverter, C320, is shown as following table:
SUNFAR C320
Inverter model
3-phase 400V
Inverter model
1-phase 220V
Inverter model
3-phase 220V
C320-4T0015
C320-2S0015
C320-2T0015
C320-4T0022
C320-2S0022
C320-2T0022
C320-4T0037
--
--
C320-4T0055
C320-2S0037
C320-2T0037
C320-4T0075
--
--
C320-4T0110
--
C320-2T0055
--
--
C320-2T0075
C320-4T0150
--
C320-2T0110
C320-4T0185
--
--
C320-4T0220
--
C320-2T0150
C320-4T0300
--
C320-2T0185
C320-4T0370
--
C320-2T0220
C320-4T0450
--
C320-2T0300
C320-4T0550
--
C320-2T0370
C320-4T0750
--
C320-2T0450
C320-4T0900
--
C320-2T0550
C320-4T1100
--
--
C320-4T1320
--
C320-2T0750
C320-4T1600
--
C320-2T0900
C320-4T1850
--
--
C320-4T2000
--
--
C320-4T2200
--
--
C320-4T2500
--
--
C320-4T2800
--
--
C320-4T3150
--
--
C320-4T3500
--
--
--
--
C320-4T4000
W1
(mm)
W
(mm)
H1
(mm)
H
(mm)
D
(mm)
Screw
123
134
223
234
165
M4
157
169
282
294
178
M5
184
204
328
344
199
M6
200
230
400
420
211
M6
232
260
450
470
233
M8
271
300
545
567
250
M8
344
381
588
614
298
M8
380
510
710
740
270
M8
400
580
760
793
300
M10
550
700
960
1000
340
M10
580
730
1103
1130
355
M10
--
--
--
--
--
--
SUNFAR C320 15
3. WIRING PROCEDURE
3.1 Precautions:
3.1.1.
3.1.2.
3.1.3.
3.1.4.
3.1.5.
3.1.6.
3.1.7.
3.1.8.
Installing a middle breaker between inverter and power supply in order to avoid enlarging the
accident.
Reducing the electromagnetic interference (EMI), please connect surge absorber to the coils of
electromagnetic contactors, relays, etc.
Frequency setting terminals (VC1, VC2, CC and PLS), Instrument circuit (AO1 and AO2), etc., these
analog signal wires should be over 0.3mm2 shield wire. Shield layer is connected with earth terminal
GND and the length of wire should be less than 30m.
Wire of relay input and output circuit(X1 ~ X6OC1OC2FWDREVRST) must be selected over
0.75mm2 shield wire. Shield layer should be connected to earth terminal CM and the length of wire
should be shorter than 50m.
Separating the main circuit wire from the signal/process circuit wiringparalleled wiring should be at
a distance of over 10cm and crossed wiring should be vertical with each other.
The wire must be less than 30m between motor and inverter. When the length of wire is over 30m,
the carrier frequency of inverter should be reduced properly.
All of leading wires should be tightened with the terminal adequately to ensure well-contact. The
leading wire of main circuit had better use the cable or cuprum tier, and wiring had better be
operated after the lug plate of corresponding sections cold pressing or welding.
Compressive resistance of all the wire should match with the voltage grade of inverter.
It is not allowed that UVW of inverter connect with the surge absorber capacitor or other surge absorber
equipment and shown as following Fig..
Motor
Inverter V
W
RC absorb device
Fig.3-1 It is prohibited to connect RC absorb apparatus
3.2 Wiring of External Components
AC
P+
PB
R / L1
C320
RUN
S / L2
Hz
J OG
<<
S ET
R EV
F WD
UP
D OW N
S TO P
T
!
E SC
W ARN ING
V
W
1.Refe r to the instruction manurl before installation

and o peration.
2.Do no t conne ct AC po we r to output te rminals U V W.
3.Do no t rem ove a ny cove r while applying pow er
and a t least 10min. after disconne ting pow er.
4.Se cure ly grou nd(ear th) the equipm ent.
Air Breaker witch
Power Supply
C320
Fig.3-2 wiring
16
SUNFAR C320
It is according to the rated input power specifications in manual.
Air-break switch
1. When the inverter is in maintenance or leave-unused, the air-break switch should isolate the
inverter with power supply.
2. Input side of inverter takes place the fault of short-circuits or low-voltage, the air-break will take the
protection.
z
z
Contactor
Control the power-on or power-off of inverter expediently.
AC electric reactor
1. Improve the power factor.
2. Reduce the harmonic wave input for the electric network.
3. Weaken the imbalance effect on 3-phase power voltage.
Brake resistor
In the situation of regenerative braking, avoiding bringing voltage too highly.
Specification of commanded equipment is shown as following table.

Model
Applied MotorKW
Wire spec
(Main circuit)
Air-break
A
Magnetic
contactor
A
G-load
P-load
C320-2S0015
1.5
--
20
18
C320-2S0022
2.2
--
32
18
C320-2S0037
3.7
--
40
32
C320-2T0015
1.5
--
20
18
C320-2T0022
2.2
--
20
18
C320-2T0037
3.7
--
40
25
C320-2T0055
5.5
--
10
63
32
C320-2T0075
7.5
--
10
63
38
C320-2T0110
11
--
16
100
50
C320-2T0150
15
--
25
160
80
C320-2T0185
18.5
--
25
160
80
C320-2T0220
22
--
25
160
95
C320-2T0300
30
--
50
200
150
C320-2T0370
37
--
50
250
170
C320-2T0450
45
--
70
250
170
C320-2T0550
55
--
95
400
225
C320-2T0750
75
--
95
400
330
C320-2T0900
90
--
150
630
330
C320-4T0015
1.5
2.2
2.5
16
12
C320-4T0022
2.2
3.7
16
12
C320-4T0037
3.7
5.5
20
18
C320-4T0055
5.5
7.5
32
Air-break
A
18
Magnetic
contactor
Model
Applied MotorKW
mm2
Wire spec
(Main circuit)
SUNFAR C320 17
G-load
P-load
C320-4T0075
7.5
11
40
25
C320-4T0110
11
15
10
63
32
C320-4T0150
15
18.5
10
63
38
C320-4T0185
18.5
22
16
100
50
C320-4T0220
22
30
16
125
50
C320-4T0300
30
37
25
160
80
C320-4T0370
37
45
25
160
95
C320-4T0450
45
55
50
200
115
C320-4T0550
55
75
50
200
150
C320-4T0750
75
90
70
250
170
C320-4T0900
90
110
70
315
225
C320-4T1100
110
132
95
400
225
C320-4T1320
132
160
95
400
330
C320-4T1600
160
185
150
630
330
C320-4T1850
185
200
150
630
400
C320-4T2000
200
220
185
630
400
C320-4T2200
220
250
185
800
500
C320-4T2500
250
280
240
800
500
C320-4T2800
280
315
240
1000
630
C320-4T3150
315
350
300
1000
630
3.3 Basic wiring
Three-phase Breaker
Three-phase
Power supply
Motor
X1
Ta
X2
Tb
X3
Tc
PLC input terminal
Earth
Programmable output
X4
X5
X6
PExternal brake resistor
PB
CM
24V Auxiliary DC power

CM
Voltmeter0~10V/ Current meter(0~20mA)
FWD Order
FWD
AO1
REV Order
REV
AO2
Fault Reset
RST
GND
Voltmeter0~10V/ Current meter(0~20mA)
CM
OC1
0 ~ 5V Frequency set
VS
OC2
VC1
CM
0 ~ 20mA Frequency set
CC
0 ~ 10V Frequency set
VC2
0 ~ 50KHz Frequency set
PLS
Open-circuit
Collector output
GND
3.4 Terminal of main circuit

Fig.3-3 C320 series of inverter basic wiring
18
SUNFAR C320
3.4.1. I model
It is fit for C320-4T0015 ~ C320-4T0075 / C320-2S0015 ~ C320-2S0037.
Brake resistance
P+
P-
PB
Earth
Motor
3-phase power supply
3.4.2. II model (It is fit for C320-4T0110C320-4T0150 /C320-2T0055C320-2T0110)

Brake resistance
P+
P-
PB E
DC Electric reactor
Earth
Motor
3-phase power
DC Brake Unit
3.4.3. III model

It is fit for C320-4T0185C320-4T0300 / C320-2T0150C320-2T0185
P+
P-
DC Electric reacor
Earth
Motor
Brake Unit
3-phase power
3.4.4. IV model It is fit forC320-4T0370C320-4T1100 / C320-2T02202T0550
P+
P-
3.4.5. V model
Brake
Baker Unite
unit
Earth
DC Electric reactor
3-phase power
Motor
It is fit forC320-4T2200C320-4T2800
SUNFAR C320 19
E a rth
3 -p h a s e p o w e r
P-
E a rth
P+
D C E le c tric re a c t o r
M o to r
B ra k e U n it
Description of terminal:
Terminal
Function
Positive Terminal of DC Negative
P-
Negative Terminal of DC / DC brake unite can be connected between P and P-.
P+
DC electric Reactor can be connected between P and P+.
PB
DC brake resistance can be connected between P and PB.
RST
Connecting three-phase AC power supply
UVW
Connecting three-phase AC motor
Earth Terminal
3.5Terminal of Control circuit
X1
TA
TB
TC
X2
X3
X5 CM RST 24V OC2 PLS CC GND AO2
X4
X6 FWD REV OC1 VS VC1 VC2 AO1 ERH +
Description of control-circuit terminal:

Type
Terminal
VS
Analog
Input
Control
Function
Notes
It provides +10V/10mA or +5V/50mA power to JP1
Switch JP1
VC1
Frequency setting voltage signal input terminal 1
0~5V
VC2
Frequency setting voltage signal input terminal 2
0~10V
CC
Frequency setting current signal input terminal
0~20mA
PLS
Pulse input signal terminal
050KHz/5~30V
GND
Common terminal of analog input signal
X1
Multi-function input terminal 1
The detailed function of

multi-function Input terminal is
20
SUNFAR C320
X2
X3
X4
X5
X6
FWD
FWD control command terminal
REV
REV control command terminal
RST
Fault reset input terminal
CM
Common terminal of control
24V
It provides +24V/50mA power and is grounded by CM.
AO1
PLC voltage signal input terminal1. It is set by F2.13 and allowed to

connect with external voltmeter.
AO2
PLC voltage signal input terminal 2. It is set by F2.14 and allowed to

connect with external voltmeter.
GND
Common terminal of AM1and AM2
Analog
Output
OC
OC1
Output
OC2
PLC
output
TA
TB
RS485
ERH
PLC open-circuit collector output is set by F3.6 and F3.7

General , TA-TB is connectedTA-TC is unconnected
when TA-TB is unconnected and TA-TC is connectedF3.8 is valid.
TC
Interface
Those terminals are valid

when being connected with
CM. And running direction
is controlled by FWD-CM
state
voltage signal input

0~20mA/0~15V and voltage
signal output 0~10V/1mA
It is selected by switch JP2
JP3
The maximum load-current is
50mA And the maximum
withstand voltage is 24V.
CapacityAC 250V 1A
Resistive load
RS485 communication interface

Grounding terminal
Description about JP
JP1
1-2 short-circuitInput +5V/50mA signal
2-3 short-circuitInput +10V/10mA signal
JP2
1-2 short-circuitAO1input voltage signal
IO1
VO2
VO1
IO2
+10V
+5V
JP1 JP2 JP3
2-3 short-circuitAO1 input current signal

JP3
1-2 short-circuitAO2 input voltage signal
2-3 short-circuitAO2 input current signal
SUNFAR C320 21
4. OPERATIONS OF INVERTER AND SIMPLE RUNNING

Operation panel has two functionsOne is to monitor the running state parameters. The other is to check and
modify the internal parameters. So operation panel has two modesMonitor mode, check and modify
parameters mode.
Usually, operation panel mode is in normal monitor mode when inverter is just power-on. At this time, current
running parameter , which is shown on operation panel , is controlled by F6.12F6.13. The operation panel
mode will return the normal monitor mode, if there isnt any operation on panel in 1 min.
4.1Operation panel
4.1.1 Panel layout
Main LED
Unit
Mode indicate light

RUN
Hz
Mode indicate light
Main LED
RUN
Hz
Auxiliary LED
Return
Unit
Potentiometer
Switch
Set
Return
ESC
JOG
<<
REV
Switch
Increasing
Jog
SET
SET
REV
FWD
FED
Stop
Decreasing
FWD
REV
Increasing
STOP
Stop
Decreasing
Fig.4-1-A Panel Layout
Fig.4-1-B Small Panel Layout
4.1.2 Keypad functions

Item
Display
Function
Main LED
It displays current state and setting parameter.
Auxiliary
LED
It displays current state and setting parameter.
AHzV
RUN
The corresponding unit of current display

Operation indicator light. The inverter is running and U, V and W output voltage.
FWD key
When F0.1 is 0 and press this key, the inverter will running forward to setting frequency according
to appointed ACC or DEC curve.
Keypad
REV key
When F0.1 is 1 and press this key, the inverter will be running backward to setting frequency
according to appointed ACC or DEC curve.
Stop and Reset key
When F0.4 is 000#, STOP is valid for panel control. If F0.4 is 000#, STOP is valid for all kinds of
control methods. If inverter occur fault, press this key to reset it and return stop mode.
If stop key is used together with
copy and read-in of internal parameters will be done.
22
SUNFAR C320
Return key
Press this key in normal monitor state to enter query mode of not normal monitor state /monitor
parameters to check running state. In any state, press this key to return the upper state.
This key is used together with
to perform Parameter read / backup.
Set key
to perform Parameter copy / write.
Data modify key

Keypad
It is used to modify the function code and parameter.

In state monitor mode, if F0.1 is 0, press this key will modify the frequency instruction
Jog key. It is valid when the state is only in operation panel control pattern
Shift key.
In any state, press
key to modify datas state. Press the key to modify
the digital bit, the modification bit will be displayed blink.
to
perform Parameter read / backup.

Panel potentiometer. Running frequency is set by potentiometer on the panel
Potentiometer turning left will reduce running frequency, potentiometer turning right will increase
running frequency
4.2 Basic function of panel and methods of operation

4.2.1 Basic functions of panel
Operation panel have functions of FWD running, REV running, JOG running, Stop, Fault reset, Modify and
check of parameter and Monitor running parameter, besides other function as follows
(1) Parameter read / backup
This function provides to copy the internal parameter of inverter and saves it permanently. (Only limit to open
internal parameter) So user can copy typical settings parameters to operate panel. These parameters dont
affect inverter running, and are checked out and modified separately.
Press
and
key simultaneous to enter parameter read / backup. Even if the inverter is running,
reading parameters is also carried though. When parameters are read, 0 is displayed blink from right to left.
After parameters backup is finished, the display is normal.
In process of parameters backup, it can be cancelled by pressing
the normal monitor state.
or
. And press
key to return
(2) Parameter copy / write

This function provides to copy the backup parameter of inverter and saves to inner storage of inverter. (Only
limit to open internal parameter) So user can copy typical settings parameters to operate panel. Those
parameters dont affect inverter running, and are checked and modified separately.
Please set F6.16 as 1 and stop the inverter before write parameter. After writing, set F6.16 as 0 to prevent
invalid parameters saving in inverter. And it had better copy the valid inner parameter to operation panel.
Please stop the inverter and then press
and
key simultaneously to enter parameter copy / write
under normal monitor mode. When parameters are writing, 0 is displayed blink from right to left. After
parameters copy is finished, the display is normal.
In process of parameters copy, it can be cancelled by pressing
the normal monitor state.
(3) Modify and check the internal parameter
Press
or
. And press
key to return
key to enter Modify and check internal parameter mode under normal mode with general ways to
check and modify data.

(4) Modify and check the backup parameter
SUNFAR C320 23
Under normal monitor mode, press 1
and
2 key simultaneously to enter Modify and check the
backup parameter mode. When panel displays function code, F in the fourth place of main LED will be
displayed blink, which means current modify and check parameters is backup parameter.
4.2.2 Methods of panel operation
(1) State parameter inquiry (eg.)
Normal Monitor Main display: 45.00

State
State Parameter Main display:

Inquiry
Output freq.
Auxiliary display: 2.3
Output current
d-0
Monitor code
Output freq.
Return
+
State Parameter Main display:
Inquiry
Parameter
Inquiry
d-5
Main display:
383
Function code
Output current
Input voltage
Output current
+
Parameter Edit
Main display:
F0.0
Auxiliary display: 0
Function code
Parameter data
24
SUNFAR C320
(2) Parameter inquiry and modify
Normal Monitor Main display:

State
Modify
backup
parameter
45.00
Output freq.
Output current
+
Parameter
Inquiry
Main display:
F0.0
Auxiliary display: 0
Give up
Modify
Function code
Parameter data
Continue Modify or
Return
+
Parameter
Inquiry
Main display:
F0.2
Function code
Give up
Modify
Parameter data
Parameter
Main display: 45.00
Parameter data
Inquiry
Output current
Parameter
Main display: 50.00
Parameter data
Modify
Output current
Parameter
Storage
Main display: F0.2

Function code
Parameter data
SUNFAR C320 25
4.3 List of state monitor parameter

Monitor Code
Content
d.0
Current output frequent
d.1
Current output current
Unit
Hz
(Valid)
d.2
Current output voltage (Valid)
d.3
Rotate speed of motor
A
V
rpm
d.4
DC bus voltage
d.5
Input voltage of inverter
d.6
Setting freq.
Hz
d.7
Count value of Internal counter
d.8
PID setting value
d.9
PID feedback value
d.10
Running linear speed
d.11
Setting linear speed
d.12
Analog input voltage VC1
d.13
Analog input voltage VC2
d.14
Analog input voltage CC
mA
d.15
External pulse input PLS
KHz
d.16
State of input terminal
d.17
Temperature of module
d.18
Analog output AO1
d.19
Analog output AO2
d.20
Magnetization current
d.21
Magnetization current setting
d.22
Torque current
d.23
Torque current setting
d.24
Reserved
d.25
Reserved
d.26
First fault record
d.27
Second fault record
d.28
Third fault record
d.29
Fourth fault record
d.30
Fifth fault record
d.31
Sixth fault record
d.32
Output frequency of last fault
Hz
d.33
Setting frequency of last fault
Hz
d.34
Output current of last fault
d.35
Output voltage of last fault
d.36
DC voltage of last fault
d.37
Temperature of module of last fault
26
SUNFAR C320
4.4 Simple Operation

4.4.1. Initialization
Frequency input channel / mode selection[F0.1]
Initialization of inverter is different according to different model. If [F0.0] is 0, the frequency of inverter is set
by keypad.
Operation channel selection[F0.4]
Initialization of inverter is different according to different model. If F0.4 is 00#0, Start and stop of inverter is
controlled by
and
key.
4.4.2. Simply operation
It is forbidden to connect Three-phase power to output terminal U, V and W directly.
Three-phase
Breaker
Power supply
R
S
T
Motor
U
V
W
E
Earth
Fig.4-1 simply running
Please connect inverter as the following fig 4-1.

Be sure that the wiring is correct and turn the power on, the inverter will display P.oFF and0.
Be sure that F0.1 is 0.
Please set parameters [F1.3] and [F1.4], according to the nameplate parameters of applied motor.
Please press
key to start inverter, then the inverter will display 0.0Hz.
Please press
key to increase input frequency and motor will run.
Observe the motor whether it runs normally or not. If abnormal, please stop running at once and turn off
the power, and find out the reason, then restart.
Press the key
to decrease the setting frequency.
Press the key
to stop running. Then turn power supply off.
Carrier wave frequency is fixed value between 1.5 and 12 KHz. If motor does not take any load, it will a slight
oscillate. So please decrease setting value of F0.16.
SUNFAR C320 27
5. PARAMETERS LIST
Symbol description:
means that this parameter can not be changed during operation.
means that this parameter is related to the inverters model.
Function Code
Name
Setting range
F0. 0 Control methods
Minimum Manufacture Modify Address

Setting
Setting
Limit
code
0V/F method 1Vector control
01H
0.01
0.0
02H
0000
03H
0000
04H
0000
06H
F0.7 The lower limit frequency 0.0 Hz~ [F0.8]
0.01
0.0
07H
F0.8 The upper limit frequency [F0.7] ~ 400.00Hz
0.01
50.00
08H
0Frequency setting by operation panel

1UP/DW Acc and Dec control
2RS485 interface
3Panel potentiometer
Frequency input channel / 4External voltage signal VC10V~5V
F0. 1
mode selection
5External voltage signal VC20V~10V
6External current signal CC0~20mA
7External pulse signal0.0~50.0KHz
8Combination setting
9External terminals
F0. 2 Frequency digital setting
Basic operation parameter unit
F0. 3
F0. 4
F0.5
F0.6
0.00 ~ the upper limit frequency
The first part of LED(form right to left)

0Setting freq. will save after power down
1Setting freq. will not save after power
down
The second part of LED
Auxiliary control of freq
0Setting freq. is keep when stopping
digital setting
1Setting freq. will save in F0.2 when
stopping
2Setting freq. is clear when stopping
The third and fourth part of LED(form right
to left)Reserved
The first part of LED (form right to left):
0Panel control
1External terminals control
2RS485 interface
Operation channel
Function of key STOP
selection
0It is valid for panel control.
1It is valid for all kinds of control method.
The third and fourth part of LED(form right
to left)Reserved
Combination methods of 0Two-line mode 1 1Two-line mode
instruction terminals
2Three-line mode
0Running direction is consistent
with setting direction
1Running direction is in contradiction
to setting direction
Running direction control
0Prevention REV is valid
1Prevention REV is invalid
The third and fourth part of LED
(form right to left)Reserved
00H
05H
28
SUNFAR C320
Function Code
Name
Setting range

Setting
Setting
Limit
code
F0.9 Reserved
F0.10 Acc time 1
0.1 ~ 6000 Sec/Min
0.1
0AH
F0.11 Dec time 1
0.1 ~ 6000 Sec/Min
0.1
0BH
0000
0CH
0.1
20.0
0DH
0.01
60.0
0EH
0FH
0.1
10H

Reserved
The second part of LED (form right to left):
0The relation between out current
and Carrier wave is off.
1The relation between out current
and Carrier wave is on.
The third part of LED (form right to left):
0The relation between module temp
1The relation between module temp
The third part of LED (form right to left):
0The relation between out frequent
1The relation between out frequent
1110
11H
F0.18 Parameter write-protect
1Forbid to modify all parameter,

except F0.2 and F0.18
2Forbid to modify all parameter,
except F0.18
12H
F1.0 Type of V/F Curve
0Constant torque curve

1Low-freq. torque curve 1
2Low-freq. torque curve 2
3V/F user-defined curve
13H
F1.1 Torque Boost
0.0~20.0
0.1
14H
F1.2 Torque boost pattern
0Manual
F1.3 Base running frequency
5.00the upper limit frequency
0.01
50.00
16H
F1.4 Max output voltage
200500V
380
220
17H
F0.12
Basic operation parameter unit
F0.13
F0.14
F0.15

0Beeline 1S curve
0Output freq. will be modified according
to Acc/Dec time.
Characteristics parameter
1Output freq. will be automatically
of Acc and Dec
modified according to lode.
The third part of LEDUnit of Acc/Dec
time
0 Sec
1Min
Reserved
Acc/Dec initial section
10.0~ 50.0 %
proportion of S curve
Acc/Dec
ascending/decline section 10.0 ~ 80.0 %
proportion of S curve
0 General-purpose lode
Lode pattern selection
1 Fan and pump lode.
F0.16 Carrier wave frequency
F0.17
Primary applied parameter unit
09H
Carrier wave
characteristics
Carrier wave characteristics
1Automatic
100250V
15H
SUNFAR C320 29
Function Code
Name
Setting range
F1.5 V/F freq. 3
[F1.7] ~ [F1.3]
F1.6 V/F voltage 3

F1.7 V/F freq. 2
F1.8 V/F voltage 2

Setting
Setting
Limit
code
0.01
0.0
[F1.8] ~ 100.0(%)
0.1
0.0
19H
[F1.9] ~ [F1.5]
0.01
0.0
1AH
[F1.10] ~ [F1.6]
0.1
0.0
1BH
F1.9 V/F freq.1
0.0 ~ [F1.7]
0.01
0.0
1CH
F1.10 V/F voltage 1
[F1.1] ~ [F1.8]
0.1
0.0
1DH
0.1
50.0
0.1
0.0
380V
220V
22H
5.00600.00Hz
0.01
50.00
23H
0.01300.0A
0.01
24H
25H
0.01
26H
27H
0001
0.01
0.30
0010
DC braking current when

F1.11
0.0 100.0%
starting
DC braking time when
F1.12
0.0 20.0S
starting
1EH
F1.13 Reserved
1FH
20H
F1.14 Compensate for slip freq. 0.0150.0%

Rated voltage of applied
F1.15
motor
Rated freq. of applied
F1.16
motor
Rated current of applied
F1.17
motor
200500V
100250V
F1.18 Rated rev of applied motor 3006000rpm

18H
Exciting current of applied

F1.19
[F1.17]/4~[F1.17]3/4
motor
0Invalid
1Determine parameters when motor is
Parameters
stop
F1.20
self-determination
2Determine parameters when motor is
run
0Starting pre-excitation is Valid
1Starting pre-excitation is Invalid
The second part of LED:
Selection of starting
0Prepare pre-excitation is valid when
F1.21
pre-excitation
zero frequency
1Prepare pre-excitation is invalid when
zero frequency
The third and fourth part of LEDReserved
Pre-excitation of starting
F1.22
0.102.00Sec
time
0Self-adapting rectify of stator
Resistance will invalid.
1Self-adapting rectify of stator
resistance will valid.
0Self-adapting rectify of excitation
current will invalid.
Self-adapting rectify of
F1.23
motor parameters
1Self-adapting rectify of excitation
current will valid.
The third part of LED
0Self-adapting rectify of rotor
Resistance will invalid.
1Self-adapting rectify of rotor
resistance will valid.
The fourth part of LEDReserved
21H
28H
29H
2AH
30
SUNFAR C320
Function Code
Name
Setting range
F1.24 Stator resistance
0.00020.000
0.001
2BH
F1.25 Rotor resistance
0.00020.000
0.001
2CH
F1.26 Rotor inductance
0.00600.00 mH
0.01
2DH
F1.27 Inductance of excitation
0.00600.00 mH
0.01
2EH
0.00100.00 mH
0.01
2FH
0.01
1.00
F1.28
Leakage inductance
(coefficient)
F1.29
Gain of compensation for

0.501.50
speed drop
30H
F1.30 Reserved
F2.0
F2.1
F2.2
F2.3
F2.4
F2.5
F2.6
31H
Input lower limit voltage

VC1
Input upper limit voltage
VC1
Input lower limit voltage
VC2
Input upper limit voltage
VC2
Input lower limit current
CC
Input upper limit current
CC
The min pulse input
F2.7 The max pulse input

Frequency with the min
setting
Frequency with the max
F2.9
setting
F2.8
Analog I/O parameter unit

Setting
Setting
Limit
code
0.0 ~ [F2.1]
0.1
0.0V
32H
[F2.0] ~ 5.0V
0.1
5.0 V
33H
0.0V ~ [F2.3]
0.1
0.0 V
34H
[F2.2] ~ 10.0V
0.1
0.0mA~ [F2.5]
0.1
4.0
36H
[F2.4] ~ 20.0mA
0.1
20.0
37H
10.0V
35H
0.0KHz~[F2.7]
0.1
0.0
38H
[F2.6]~50.0 KHz
0.1
10.0
39H
0.0~[F2.9]
0.01
0.0
3AH
[F2.8]~550.0Hz
0.01
50.00
3BH
0000
0.01
0.10
3DH
3EH
F2.10
Characteristics selection
of input channel
The first part of LED (form right to left)

(VC1channel)
0 positive characteristics
1Negative characteristics
The second part of LED(VC2 channel)
The third part of LED(CC channel)
The fourth part of LEDpulse channel
F2.11
External freq. set time

constant of filtering
0.011.00Sec
F2.12 Combination setting mode See the explanations about F2.12
3CH
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
SUNFAR C320 31
Analog I/O parameter unit
Function Code
F2.13
Name
Setting range
Analog output selection

AO1AO2
The lower limit of analog

output AO1
The upper limit of analog
F2.15
output AO1
The lower limit of analog
F2.16
output AO2
The upper limit of analog
F2.17
output AO2
F2.14

AO1output
0Output freq.
1Output current
2Output voltage
3Rotate speed of applied motor
4PID setting
5PID feedback
The second part of LEDAO2 output
0Output freq.
1Output current
2Output voltage
4PID setting
5PID feedback

Setting
Setting
Limit
code
0010
3FH
0.0[F2.15]
0.1
0.0 V
40H
[F2.14]12.0
0.1
10.0V
41H
0.0[F2.17]
0.1
2.0 V
42H
[F2.16]12.0
0.1
10.0V
43H
F2.18 Reserved
F3.0
Digital O/I parameter unit
F3.1
F3.2
F3.3
F3.4
F3.5
44H
Function selection of input 0Control terminal is idle

1Multi-speed control terminal 1
terminal 1 (0~25)
4Wobble freq. is valid
Function selection of input 5State of wobble freq. reset
terminal 2 (0~25)
6FWD jog control 7REV jog control
8Acc& Dec time selection terminal 1
9Acc& Dec time selection terminal 2
10Freq. setting channel selection 1
Function selection of input
terminal 3 (0~25)
13Freq. is controlled gradually increase
UP
Function selection of input 14Freq. is controlled gradually increase
terminal 4 (0~25)
DW
15UP-DW freq. clear
16Uncontrolled stop control
17Fault signal of peripheral equipment
input
terminal 5 (0~25)
18Three-line mode running control
19DC braking control
20Inner counter clear
21Inner counter timer
22PLC running valid
23PID running valid
terminal 6 (0~25)
24Reserved
25PLC state reset after stopping
45H
46H
47H
48H
13
49H
14
4AH
32
SUNFAR C320
Digital O/I parameter unit
Function Code
Name
Setting range
0In the running

1Frequency reaching
2Freq. level detection signalFDT
F3.6 Output terminalOC1 3Over-loading alarm
4External fault halt
5Output frequency reaches the
upper-limit
6Output frequency reaches the
lower-limit
7Running in zero speed
F3.7 Output terminalOC2 8Inverter will stop when under voltage
9PLC stage is end of run
10PLC periodic is end of run
11Reserved
12Setting value of counter arrives
13Designated value of counter arrives
14Reserved
TA, TB and TC of relay
15Reserved
F3.8
contactsTATBTC 16Inverter fault
17Restrictions on wobble freq. of the
upper and lower limit freq.

Setting
Setting
Limit
code
4BH
4CH
16
4DH
0.0~20.00Hz
0.01
5.00
4EH
F3.10 FDT setting 1
0.0~ the upper limit freq.
0.01
10.00
F3.11 FDT output delay time 1
0.1~200.0S
0.1
2.0
F3.12 FDT setting 2
0.0~ the upper limit freq.
0.01
10.00
F3.13 FDT output delay time 2
0.1~200.0 Initial freq. of DC braking

When stopping
0.1
2.0
F3.14 Over-loading alarm level
50~200%
110
Over-loading alarm
F3.15
delay time
0.0~20.0 S
0.1
2.0
F3.9
Frequency reach the

checkout amplitude
4FH
51H
52H
53H
F3.16 Reserved
Auxiliary running parameter unit
50H
54H
55H
F4.0 Start mode
0Routine mode
1Detect speed and restart
F4.1 Start frequency

F4.2 Start frequency duration
F4.3 Stop mode
0Decelerate mode
1Uncontrolled stop
0.010.00Hz
0.01
0.5
0.020.0 S
0.1
0.0
59H
0.01
3.00
5AH
0.1
0.1
5BH
0.1
0.0
DC braking current when

F4.7 stopping
0.0100%
0.1
50.0
5DH
Running threshold of zero

F4.8 freq.
0.0100.0Hz
0.01
0.0
5EH
Return different of zero

F4.9 freq.
0.050.00Hz
0.01
1.00
5FH
F4.10 Jog frequency
0.0the upper limit freq.
0.01
10.00
60H
F4.11 Acc torque level
110200%
160
61H
Initial freq. of DC braking

F4.4
0.050.00Hz
when stopping
Waiting time of DC
F4.5
0.05.0 S
braking when stopping
Action time of DC braking
F4.6 when stopping
0.020.0 S
56H
57H
58H
5CH
SUNFAR C320 33
Function Code
Name
Setting range
F4.12 Braking torque lever
10150%
Motor over-lode protection

50110%
F4.13
coefficient
0Invalid
Automatic voltage
1 Dynamic valid
F4.14
regulationAVR
2Static valid
Auxiliary running parameter unit
F4.15 Energy-saving running
0Invalid
1Valid

Setting
Setting
Limit
code
1
80
62H
110
63H
64H
65H
F4.16 Dead time of FWD&REV 0.05.0S
0.1
0.0
66H
F4.17 Acceleration time 2
0.16000 s/min
0.1
67H
F4.18 Deceleration time 2
0.16000 s/min
0.1
68H
F4.19 Acceleration time 3
0.16000 s/min
0.1
69H
F4.20 Deceleration time 3
0.16000 s/min
0.1
6AH
F4.21 Acc time 4/Jog Acc time
0.16000 s/min
0.1
6BH
F4.22 Dec time 4/Jog Dec time
0.16000 s/min
0.1
6CH
0.01
10.00
6DH
700V
6EH
60
6FH
0010
70H
0.1
0.5
71H
Modified rated of UP/DW

0.01100.0Hz/Sec
terminals
Start voltage of dynamic
600~750V
F4.24
braking
Action ratio of dynamic
10~100%
F4.25
braking
The first part of LED
0Invalid 1 Valid
Restart after power down The second part of LED
F4.26
setting
0Routine mode
1Detect speed and restart mode
Waiting time of restart
0.010.0s
F4.27
after power down
F4.23
Multi-speed running parameter unit
F4.28 Reserved
72H

PLC setting
0PLC is invalid.
1PLC is valid.
2PLC is conditional invalid.
Simple PLC running mode selection
0Single loop mode
1Single loop and stop mode
2Continuous loop mode
3Continuous loop and stop mode
F5. 0 Multi-speed running mode 4Keep the end value
5Keep the end value and stop mode
0Restart from the first stage freq.
1Restart from running freq., which is
saved before running is break
2Restart from setting freq. when
Running is break.
The fourth part of LEDPLC save state
0Non-save after power off
1Save after power off
0000
73H
F5. 1 Multi-speed frequency 1
0.0 ~ the upper limit freq.
0.01
35.00
74H
0.01
15.00
75H
0.01
3.00
76H
34
SUNFAR C320
Function Code
Setting range

Setting
Setting
Limit
code
F5.4 Multi-speed frequency 4
0.01
20.00
77H
0.01
25.00
78H
0.01
30.00
79H
0.01
35.00
7AH
0.01
40.00
7BH
0.06000s
0.1
10.0
7CH
0.06000s
0.1
10.0
7DH
0.06000s
0.1
10.0
7EH
0.06000s
0.1
10.0
7FH
0.06000s
0.1
10.0
80H
0.06000s
0.1
10.0
81H
0.06000s
0.1
10.0
82H
0.06000s
0.1
10.0
83H
0000
84H
0000
85H
F5.9
F5.10
F5.11
F5.12
Name
F5.13
F5.14
F5.15
F5.16
Running time of
Multi-speed 1
Running time of
Multi-speed 2
Running time of
Multi-speed 3
Running time of
Multi-speed 4
Running time of
Multi-speed 5
Running time of
Multi-speed 6
Running time of
Multi-speed 7
Running time of
Multi-speed 8

0 Stage 1 FWD 1Stage 1 REV
Running direction of PLC 0 Stage 2 FWD 1Stage 2 REV
F5.17
multi-speed
The fourth part of LED
Running direction of PLC 0 Stage 6 FWD 1Stage 6 REV
F5.18
multi-speed
Advanced running parameter unit
F5.19 Reserved
86H
0Off
Inverter stop when motor
F6.0
1Inverter will run when motor
is cut off
is connected with it.
87H
F6.1 Fault self-recovery time
012
88H
F6.2
Interval time of fault

self-recovery
0.220S
0.1
2.0
89H
F6.3
Final value setup of

internal counter
160000
8AH
F6.4 Internal timer setup
160000
F6.5 Skip freq. 1
0.01
0.0
8CH
0.05.00Hz
0.01
0.0
8DH
0.01
0.0
8EH
F6.6
Amplitude accumulation
Of Skip freq. 1
F6.7 Skip freq. 2
8BH
SUNFAR C320 35
Advanced running parameter unit
Function Code
Name
Setting range
F6.8
Amplitude accumulation
of Skip freq. 2
0.05.00Hz
0.01
0.0
8FH
F6.9
Linear speed coefficient

setting
0.01100.0
0.01
1.00
90H
F6.10
Close-loop analog
coefficient setting
0.01100.0
0.01
1.00
91H
F6.11
Rotator speed coefficient

0.0110.00
setting
0.01
1.00
92H
F6.12 Monitor item selection 1
011
93H
F6.13 Monitor item selection 2
011
94H
0 ~ 9999
95H
0Parameter initialization is off.

1Parameter initialization is on.
2Clean fault records
F6.14
Query or modify
parameters
F6.15 Parameter initialization
F6.16 Copy parameter function 0Forbid
Wobble freq. running parameter unit

Setting
Setting
Limit
code
1Allow
96H
97H
F6.17 Manufactory password
09999
1000
98H
F6.18 User password
09999
100
99H
F6.19 Reference password
0 ~ 9999
9AH
1000
F7.0
Wobble freq. running

mode

0Function of wobble freq. is invalid.
1Function of wobble freq. is valid.
2Function of wobble freq. is conditional
valid.
The second part of LED: restart mode
0 Restart according to parameters saved
before stop
1 Restart
The third part of LED: wobble freq
characteristics
0The wobble freq. is changeable.
1The wobble freq. is fixed
The fourth part of LED: Storage
characteristics of wobble freq.
0It will not save the running state of
wobble freq. after power off
1It will save the running state of wobble
freq. after power off
F7.1
Preset freq. of wobble

freq.
0.01
10.00
F7.2
Waiting time of preset

freq.
0.06000.0s
0.1
0.0
F7.3 Amplitude of wobble freq. 0.050.0%
0.1
10.0
F7.4 Jumping freq.
0.080.0%
0.1
10.0
9FH
F7.5 Triangular rise time
0.11000.0s
0.1
10.0
A0H
F7.6 Triangular fall time
0.11000.0s
0.1
10.0
A1H
Preset center freq. of

F7.7
wobble freq.
0.01
10.0
A2H
F7.8 Reserved
9BH
9CH
9DH
9EH
A3H
36
SUNFAR C320
Function Code
Name
Setting range
PID control parameter unit
F8.0 Inner PID control

Setting
Setting
Limit
code

Inner PID control
0Inner PID control is invalid
1Inner PID control is valid
2Inner PID control is conditional valid.
PID controller selection
0proportion
1Integral
2Proportion and integral
The third part of LED Regulating
property of PID controller
0positive interaction
1Reactor
The fourth part of LED:
0PID with unidirectional control
1PID with two directions control
0020
A4H
0000
A5H
F8.1
Inner PID setting and

channel selection

0Digital setting. It is set by parameter
F8.2.
1Serials interface setting
2Panel potentiometer setting, it is on
the operation panel.
The second part of LED Reserved.
It is used to set PID feedback channel.
0External voltage input VC1
1External voltage input VC2
2External current input CC
3Pulse input PLS
4VC1+CC
5VC1-CC
6Min (VC1, CC)
7Max (VC1, CC)
The fourth part of LED: Reserved
F8.2
Inner PID close-loop

digital setting
0.0010.00V
0.01
0.0
A6H
F8.3 Minimum fixed value
0.0[F8.4]
0.01
0.0
A7H
F8.4 Maximum fixed value
[F8.3]10.00
0.01
10.00
A8H
0.010.00
0.01
0.0
A9H
0.010.00
0.1
10.00
AAH
F8.7 Proportion gain
0.05.00
0.01
1.00
ABH
F8.8 Integral time constant
1.0500.0s
0.1
10.0
ACH
F8.9 Allowable deviation limit
0.020.0%
Feedback of minimum
F8.5
fixed value
Feedback of maximum
F8.6
fixed value
0.1
0.0
ADH
F8.10 Preset freq. for close-loop 0.0the upper limit freq.
0.01
0.0
AEH
Holding time of preset

F8.11
freq. for close-loop
0.06000.0s
0.0
0.0
F8.12 Sleeping threshold
0.010.00
0.01
10.00
AFH
B0H
SUNFAR C320 37
Function Code
Name
Setting range
F8.13 Awakening threshold
0.010.00

Setting
Setting
Limit
code
0.01
0.0
B1H
Serials communication parameters
F8.14 Reserved
B2H
F9.0 Communication setting

It is used to set baud rate of serials
communication.
0Reserved
1: 1200bps
2: 2400bps
3: 4800bps
4: 9600bps
5: 19200bps
To set data format of serials
communication.
0Close
1 Even
2Odd
Reserved.
F9.1 Local address
030
B4H
F9.2 Response delay of local
01000ms
5ms
B5H
Function setting of
F9.3 communication
Auxiliary function

0: The inverter is guest
1: The inverter is host
The second part of LED Act selection
after communication is lost
0Stop 1Keep
The third part of LED: Reserved.
Communication protocol setting, form 0
to 1
0010
B6H
0.0100.0s
0.1
10.0
B7H
F9.5 Linkage setting proportion 0.0110.00
0.01
1.00
B8H
B9H
F9.4
Checkout time of
communication overtime
0Close
1Panel potentiometer
Rectify channel 2
Rectify channel of linkage External voltage signal VC10 ~ 5V
F9.6
setting proportion
Rectify channel 3
External voltage signal VC20 ~ 10V
Rectify channel 4
External current signal CC0 ~ 20mA
0014
Special function parameter unit
F9.7 Reserved
B3H
BAH
Under voltage protection

FC.0
level
360480V
390
BBH
FC.1 Over voltage limit level
660760V
700
BCH
180
BDH
FC.2
Current amplitude limiting

150200
level
FC.3 Reserved
FC.4
BEH
Protection function in
operation

Under voltage compensation intensity
The second part of LED Over voltage
inhibit intensity
Over current inhibit intensity
The fourth part of LEDSelf-adapting
braking torque adjust intensity
3333
BFH
38
SUNFAR C320
Special function parameter unit
Function Code
Name
Setting range

Setting
Setting
Limit
code
FC.5 Action function selection
the first part of LED(form right to left)

Cooling fan control
0Cooling fan run after inverter run.
1Cooling fan will automatic run when
inverter is power on.
Variable speed control of cooling fan
0Invalid
1Valid
Cooling fan always keep the max speed.
Voltage over modulation
0Invalid
1Valid
The fourth part of LEDReserved.
0000
C0H
FC.6 Function setting
the first part of LED(form right to left)

0All of parameters can be modified.
1All of parameters wont be modified.
0It will valid when Input terminals are
connected.
1It will valid when Input terminals are
disconnected.
Reserved.
0000
C1H
FC.7 Reserved
C2H
FC.8 Agency password
0 ~ 9999
FC.9 Rotate speed coefficient 0.105.00

Gain of closed loop of
FC.10 rotate speed
0.501.20
Integral time constants of
FC.11 closed loop of rotate
0.1010.00
speed
100
C3H
0.01
1.00
C4H
0.01
1.00
C5H
0.01
1.00
C6H
Compensation rectify of
FC.12 dead zone
025
C7H
FC.13 Program version
21002199
C8H
SUNFAR C320 39
6DESCRIPTION OF SPECIFIC FUNCTIONS

6.1 Basic operation parameter unit
F0.0 Control methods
Setting range0 ~ 1
It is used for selecting control method when inverter is working.

0V/F method
It is used for variable speed inverter occasions where do not demand high performance of speed control and
low-frequency torque.
1Vector control
It is used for the variable speed inverter occasions with high performance.
It will get prime performance when inverter matches the same capacity motor in vector control.
Explanations
1. It need use some basic parameters of motor when inverter takes vector control. C320 serial inverter
provides those basic parameters of motor, and those parameters were set.
2. When basic parameters of applied motor are different from parameters provided by inverter, those
parameters must be set again (code [F1.15] ~ [F1.18]). Users can get those parameters by setting code
F1.20 (Parameters self-determination).
Note: if users have no nameplate parameters of applied motor or inverter inverters some motors, please take
V/F method.
F0.1 Frequency input channel / mode selection
Setting range0 ~ 9
It is used for selecting input channel of frequency instruction.

0 Frequency setting by operation panel
Set frequency of inverter can be set by parameter F0.2 as well as by the key
and
on the
operation panel in normal monitor mode.
1 UP/DW Acc and Dec control
Running frequency is set by terminals UP and DW. And controlled terminals UP and DW can be selected by
parameters [F3.0]~[F3.5]. When UP is on, the running frequency will increase. When UP is on, the running
frequency will decrease. When UP and DW is on or off together with CM, running frequency will fix. The rate
of modified frequency of terminals UP and DW is set by parameter F4.23.
2 RS485 interface
It receives instruction of setting frequency form the master.
3 Panel potentiometer
Running frequency can be set by potentiometer on the operation panel.
4 External voltage signal VC1
Running frequency is set by external voltage signal VC1. (VC1 is form 0.0 to 5.0V) Please set the VC1 by the
parameters F2.0 and F2.1.
5 External voltage signal VC2
Running frequency is set by external voltage signal VC2. (VC2 is form 0.0 to 10.0V) Please set the VC2 by
the parameters F2.2 and F2.3.
6 External current signal CC
Running frequency is set by external current signal CC. (CC is form 0.0 to 20.0mA) Please set the CC by the
parameters F2.4 and F2.5.
40
SUNFAR C320
7 External pulse signal

Running frequency is set by external pulse signal. (It is form 0.0 to 350.0KHz, and the amplitude
accumulation is form 5 to 30V) Please set the pulse signal by the parameters F2.6 and F2.7.
8 Combination setting
Running frequency is set by linear combination of each channel, and combination mode is decided by
parameter F02.12.
9 External terminals
External terminals set input channel of frequency. And it can be set by parameters F3.0F3.5.
Freq. Setting terminal 3
Frequency setting by operation panel
UP/DW Acc and Dec control
RS485 interface
Panel potentiometer
External voltage signal VC1
External voltage signal VC2
External current signal CC
External pulse signal
F0.2 Frequency digital setting
Freq. Setting channel
Setting range0.0 ~ the upper limit frequency
When F0.1 is 0, Frequency digital setting controls output frequency of inverter. In normal monitor state,
user can use the key
and
to modify this parameter.
As for F0.1 is s 1 or F0.1 is 2, the frequency will save in parameter F0.3 after power off, if F0.3 is 00#0.
F0.3
Auxiliary control of freq. digital setting
Setting range0000 ~ 0021
When F0.1 is 0, 1 or 2, set parameter F0.3 to ensure that setting freq. is or not be saved in F0.2.
0Inverter will run in setting freq. that is storage in F0.2 after stopping
1Setting freq. will loss after stopping. And inverter will run in 0.0Hz when restarting
The second part of LED(form right to left)
0Setting freq. is kept when stopping
1Setting freq. will save in F0.2 when stopping
2Setting freq. is clear when stopping
The third and fourth part of LED(form right to left)Reserved.
F0.4 Operation channel selection
Setting range 0000 ~ 0012
It is used for selecting operation channel of inverter and function of key

.
The first part of LED (form right to left): to select operation channel of inverter.
0Panel control
The inverter is controlled by key
,
,
and
on the panel. And FWD state will affect output
phase sequence of inverter. When FWD is on with CM, output phase sequence will reverse with setting
sequence, contrariwise, output phase sequence will go the same way with setting sequence.
1External terminals control
The inverter receives running instruction form external terminals FWD, REV and CM. The manufacture
setting is shown as follow.
SUNFAR C320 41
Instruction
FWD
Stop instruction
REV
Terminals
FWD
FWD
FWD
FWD
State
REV
REV
REV
REV
CM
CM
CM
CM
2 RS485 interface
The inverter will receive running instruction from master.
The second part of LED (form right to left): to select function of the key
.
0It is valid for panel control.
When F0.4 is 0, Stop key on the operation panel is available.
1It is valid for all kinds of control method.
When F0.4 is not 0 and press stop key
, inverter will emergency stop and twinkling display Fu.16.
The third and fourth part of LED(form right to left)Reserved.
F0.5 Combination methods of instruction terminals
Setting range0 ~ 2
It is used for setting control mode of external terminals.

This parameter will valid only when F0.4 is set as 1.
0Two-line mode 1 Manufacture Setting

Introduction
FWD
Stop instruction
Terminals
State
REV
FWD
FWD
FWD
FWD
REV
REV
REV
REV
CM
CM
CM
CM
0Two-line mode 2
Introduction
FWD
Stop instruction
REV
Terminals
FWD
FWD
REV
REV
State
CM
CM
CM
CM
2Three-line mode
Please select a three-line mode terminal to set three-line mode. (Refer to description of parameters F3.0 ~
F3.5) Xis three-line mode terminalsand it is any one among terminals X1 ~ X6.
Switch function is shown as follow
1. SW1 Stop trigger switch of inverter
Output freq.
2. SW2 FWD trigger switch

3. SW3 REV trigger switch
SW1
X?
SW2
SW3
FWD
REV
SW1
CM
SW2
SW3
Fig.6-1 three-line mode wiring
Fig.6-2 output freq. when three-line mode
42
SUNFAR C320
F0. 6
Running direction control
This parameter is used for modifying the present output phase sequence of inverter, which modifies the
running motor direction. Control effect of panel control method is shown as following table.
Parameter F0.4 is valid together with direction control of external terminals.
F0.7
F0.8
FWD-CM
[F0.6]
OFF
##1#
FWD
ON
##1#
FWD
OFF
##00
FWD
OFF
##01
REV
ON
##00
REV
ON
##01
FWD
The lower limit frequency

The upper limit frequency
Direction
Setting range0.0 ~ [F0.8] Hz

Setting range[F0.7] ~ 400.00Hz
When setting freq. is lower than lower limit freq., the inverter will run in lower limit freq. But the parameters
F4.8 and F4.9 are priority over F0.7 and F0.8.
F0.9
Reserved
F0.10
F0.11
Acc time 1
Dec time 1
Setting range0.1 ~ 6000 Sec/Min

Setting range0.1 ~ 6000 Sec/Min
Acc time 1 is the time of output frequency accelerating from 0.0 Hz to 50.00Hz.
Dec time 1 is the time of output frequency decelerating from 50.00 Hz to 0.00Hz.
Units of Acc and Dec are set by parameter F0.12.
F0.12
characteristics parameter of Acc and Dec
The first part of LED(form right to left)It is used for setting curve type when inverter is accelerating or
decelerating, shown as fig6-3.
0Beeline
Output freq. of inverter will increase or decrease according to fixed rated.
1S curve
Output freq. of inverter will increase or decrease according to graded rated. Characteristics of S curve is set
by parameter F0.13 and F0.14.
The second part of LEDTo set Acc/Dec method
0Output freq. will be modified according to Acc/Dec time.
1Output freq. will be automatically modified according to load.
The third part of LEDIt is used for setting unit of Acc/Dec time, namely unit of parameters F0.10, F0.11,
F4.17, F4.18, F4.19, F4.20, F4.21 and F4.22.
0 Sec.
1 Minute
SUNFAR C320 43
Output freq.Hz
Beeline
S curve
TSec/min
[F0.13][F0.14]
Fig.6-3 Acc/Dec curve
F0.13
F0.14
Acc/Dec initial section proportion of S curve

Acc/Dec ascending/decline section proportion of S curve
Setting range10.0 ~ 50.0(%)

Setting range: 10.0 ~ 80.0(%)
Parameters F0.13 and F0.14 define characteristics of S curve. It is totally divide into three sections, shown as
fig6-13.
Acc/Dec initial section is process that slope of output freq. is gradual increase form 0. The slope will fix in
Acc/Dec ascending/decline section. And the slope will gradual decrease to 0 in end section.
F0.15 Load pattern selection
0 General-purpose load.
Setting range01
1 Fan and pump load.
F0.16 Carrier wave frequency
Setting range 1.5 ~ 10.0 KHz
Carrier wave frequency influences audio-frequency noise and calorific effect in running.
When environment temperature is too high and motors load is too heavy, carrier frequency should be
decreased properly to improve the heat thermal performance.
F0.17 Carrier wave characteristics
It used for setting correlated characteristics about carrier wave.

F0.18
Parameter write-protect
Setting range12
It is used for preventing error modify about data.

1Forbid to modify all parameter, except F0.2 and F0.18.
2Forbid to modify all parameter, except F0.18.
In running, some parameters cannot be modified. At this time , if try to modify these parameters, the
inverter will display , please turn off the inverter before modify those parameters.
6.2 Primary application of parameter unit

F1.0
Type of V/F Curve
Setting range 0 ~ 3
0: Constant torque curve

The output voltage of inverter is in direct ratio to the output frequency, and most load take this mode.
1: low-freq. torque curve 1
The output voltage of inverter is conic with the output frequency, which is suited to the fan and pump load.
2: low-freq. torque curve 2
The output voltage of inverter is conic with the output frequency, which is suited to the constant power load,
such as fan, pump, etc. If there is some unstable phenomenon in light-load running, please switch to run in
44
SUNFAR C320
the decreasing torque curve 1.

3: V/F user-defined curve
It is used for setting user-defined curve which user needs.
Voltage
[F1.4]
The max
output
voltage
Constant torque curve

Decreasing torque curve 1
Decreasing torque curve 2
[F.1.3]
Fig. 6-4 V/F curve
F1.1 Torque Boost(output voltage at 0 Hz)
Setting range0 ~ 20%
It is used for improving the low-frequency torque characteristics. In low-frequency running, it will make boost
compensation for the output voltage of inverter, as shown in Fig.6-5.
Boost voltage =
[F1.4]
[F1.1]
[F1.4]
200
Voltage
[F1.4]
Voltage
[F1.1]
[F1.1]
Boost voltage
Boost voltage
f
[F1.3]
[F1.3]
1Decreasing torque curve
2Constant torque curve
Fig.6-5 Torque boost
F1.2 Torque boost pattern
Setting range0 1
0Manual
Torque boost voltage is completely controlled by F1.1. There are two features: voltage will steady boost. And
motor will easily magnetic saturation when light-load.
1Automatic
Torque boost voltage is changed with the stator current of motor. The boost voltage is higher with the stator
current higher.
Boost voltage =
[F1.1]
200
[F1.4]
Inverters output Current

2inverters rated current
Auto torque boost can prevent the magnetic saturation, as the boost voltage is too high with light load, which
SUNFAR C320 45
can avoid the over-heat phenomenon of motor in low frequency running.
F1.3 Basic running frequency
F1.4 Max output voltage
Setting range 5.00 ~ the upper frequency

Setting range 200 ~ 500V/100~250V
Basic running frequency is corresponding minimum frequency when output voltage of inverter is highest.
Usually, it is rated frequency of motor.
Max output voltage is corresponding output voltage when inverter outputs the basic running frequency.
Usually, it is rated voltage of motor.
F1.5
F1.6
F1.7
F1.8
F1.9
F1.10
V/F freq. 3
V/F voltage 3
V/F freq. 2
V/F voltage 2
V/F freq. 1
V/F voltage 1
Setting range: [F1.7] ~ [F1.3]

Setting range: [F1.8] ~ 100%
Setting range: [F1.9] ~ [F1.5]
Setting range[F1.10] ~ [F1.6]
Setting range: 0.0 ~ [F1.7]
Setting range[F1.1] ~ [F1.8]
Those parameters are used for setting user-defined curve which user need. Shown as Fig.6-6 below:
Voltage
[F1.4]
[F1.6]
[F1.8]
[F1.10]
[F1.1]
Freq.
[F1.9]
[F1.7] [F1.5] [F1.3]
Fig.6-6 V/Fuser-defined curve
F1.11 DC braking current when starting

F1.12 DC braking time when starting
Setting range0.0 ~ 100.0

Setting range0.0 ~ 20.0 S
Those parameters are fit for occasion that inverter needs brake before start. Shown as Fig.6-7.
F1.11=
DC braking current when starting

Rated current of inverter
100%
When rated current of motor is lower than rated current of inverter, please pay attention to set
F1.11.Make sure that DC braking current is lower than rated current of motor.
Parameter F1.12 defines duration that inverter output DC braking current. When F1.12 is 0, DC braking is
invalid when starting.
46
SUNFAR C320
Output Freq.
Starting
freq.
DC braking
[F1.12]
[F4.4]
[F4.1]
Output
current
[F1.11]
[F4.7]
[F4.6]
Instruction
[F4.2]
[F4.5]
Fig.6-7 Process of start and stop
F1.13
Compensate for slip freq.
Setting range 0.0 ~ 150
The inverter will modify output freq. automatically to offset effects that is act on rotate speed of motor form
load.
Output freq.
Compensation for slip freq. is 100%
150%
100%
Before
After
50%
Rotor speed
Fig.6-8 Compensate for slip freq.
F1.14
F1.15
F1.16
F1.17
Rated voltage of applied motor

Rated freq. of applied motor
Rated current of applied motor
Rated rev of applied motor
Setting range 200 ~ 500/100 ~ 250 V

Setting range 5.00 ~ 300.00 Hz
Setting range 0.01 ~ 300.0 A
Setting range 300 ~ 6000 RPM
They are nameplate parameters of applied motor. The running performance will improve if those parameters
are input correctly.
F1.18
Reserved
F1.15
F1.16
F1.17
F1.18
F1.19
Rated voltage of applied motor

Rated freq. of applied motor
Rated current of applied motor
Rated rev of applied motor
Exciting current of applied motor
Setting range 200 ~ 500/100 ~ 250 V

Setting range 5.00 ~ 300.00 Hz
Setting range 0.01 ~ 300.0 A
Setting range 300 ~ 6000 rpm
Setting range [F1.17]/4 ~ [F1.17]3/4
Those parameters are nameplate data of applied motor. And they need input one by one according to
capacity of applied motor, when inverter takes vector method.
Generally, exciting current of applied motor neednt modify. Because it will automatic update when rated
current of applied motor is modified.
F1.20 Parameters self-determination
0 It will invalid.
Setting range 0 ~ 3
SUNFAR C320 47
1 Determine parameters when motor is stop
2 Determine parameters when motor is runReserved
Both vector control method and panel control method are valid, parameter F1.20 will act.
When parameter F1.20 is valid, inverter will determine parameters by press key
Parameters will save
automatically in inverters memory and Parameter F1.20 will to clear.
Before start function of Parameters self-determination, please make sure that nameplate parameters of
motor[F1.15] ~ [F1.18]are input correctly and motor stops.
When capacity of applied motor is equally match inverters, user starts function of Parameters
self-determination is not necessary.
If motor isnt connect with inverter correctly, self-determination will stop and LED of inverter will show fault
Fu.30Fu.33.
F1.21
F1.22
Selection of starting pre-excitation

Pre-excitation of starting time

Setting range 0.10 ~ 2.00 Sec
Those parameters are used for defining pre-excitation of motor startup.

It needs some time to set motor air-gas flux (approximate rotor time). In order to get enough start torque, it
must set air-gas flux beforehand when motor is stop but it will start.
Those parameters will be valid while inverter takes vector control method only.
parameters[F1.21] set by binary system
The first part of LED (form right to left): To start Pre-excitation
0To start Pre-excitation is invalid.
It doesnt need to set air-gas flux beforehand when motor is from stopping to start.
In order to achieve vector control, inverter will forcibly give motor an excitation current, even parameter
F1.21 is set 0.
1To start pre-excitation is valid

To give motor a pre-excitation before it startup, Pre-excitation of starting time is set by parameter [F1.22].
The second part of LED (form right to left): zero-freq. excitation preparation
0Prepare pre-excitation is invalid when zero frequency
When inverters Instruction is running, but the output freq. is 0, inverter will close off output power and the
stator current of motor is 0.
1Prepare pre-excitation is valid when zero frequency
When inverter is running, it will output excitation current even the freq. output is 0. So there is no
pre-excitation of starting time when start-up motor.
The second and third part of LED (form right to left) reserved.
Current
[F1.19]
Output freq.
[F1.22]
Fig. 6-9 TO start pre-excitation
48
SUNFAR C320
F1.23
Self-adapting rectify of motor parameters
It is used for selecting self-adapting rectify of motor parameters functionset by binary system.
The first part of LED (form right to left): to select self-adapting rectify of stator resistance function
0:Self-adapting rectify of stator resistance is invalid
1:Self-adapting rectify of stator resistance is valid
The second part of LED (form right to left): to select self-adapting rectify of excitation function
0:Self-adapting rectify of excitation is invalid
1:Self-adapting rectify of excitation is valid
The third part of LED (form right to left): to select self-adapting rectify of rotor resistance function
0:Self-adapting rectify of rotor resistance is invalid
1:Self-adapting rectify of rotor resistance is valid
The fourth part of LED (form right to left): reserved.
Some parameters of motor have been influenced by temperature change, and control performance is
affected if setting value isnt precision. When motor have selected corresponding function, inverter will
optimize parameters automatically in running, which can improve the performance and stability of motor.
F1.24
F1.25
F1.26
F1.27
F1.28
stator resistance
rotor resistance
rotor inductance
excitation inductance
Leakage inductance (coefficient)
Setting range 0.000 ~ 20.000

Setting range 0.00 ~ 600.00 mH
Those parameters are used for setting motors basic parameter. They are necessary for complete vector
control arithmetic. Client can use inverters interior parameters when capacity of inverter matches motors.
When the performance of inverter cant satisfy the users demand, you can use function of parameters
self-determination to renew some parameters. If user can get these parameters precisely beforehand,
parameters also can be input one by one. When parameters are initializing, inverter will renew interior
acquiescence parameter according to type.
Before start function of parameters self-determination, user must make sure that input nameplate parameter
of motor.
F1.29
Gain of compensation for speed drop
Parameter F1.29 is valid when inverter takes vector control method. It is used for offsetting error of setting
motor rotor parameter. The parameter is read only.
F1.30
Reserved
6.3 Analog I/O parameter unit

F2.0
F2.1
VC1 input lower limit voltage

VC1 input upper limit voltage
Setting range 0 .0 V ~ [F2.1]

Setting range [F2.0] ~ 5.0 V
F2.2
F2.3
VC2 input lower limit voltage

VC2 input upper limit voltage
Setting range 0V ~ [F2.3]

Setting range [F2.2] ~ 10.0V
F2.4
F2.5
CC input lower limit voltage

CC input upper limit voltage
Setting range 0.0 mA ~ [F2.5]

Setting range [F2.4] ~ 20.0 mA
F2.6
F2.7
The min pulse input

Tthe max pulse input
Setting range 0.0 KHz ~ [F2.7]

Setting range [F2.6] ~ 50.0 KHz
SUNFAR C320 49
[F2.0] and [F2.1] define the range of analog input voltage channel VC1, and it should be set according to the
actual input signal.
[F2.2] and [F2.3] define the range of analog input voltage channel VC2, and it should be set according to the
[F2.4] and [F2.5] define the range of analog input current channel CC, and it should be set according to the
[F2.6] and [F2.7] define the freq. range of external pulse signal.
F2.8
F2.9
Frequency with the min setting

Frequency with the max setting
Setting range 0.0Hz ~ [F2.9]

Setting range [F2.8] ~ 550.0Hz
They define the Corresponding relation between analog input (pulse input) and setting frequency. Shown as
fig.6-9.
F2.10
Characteristics selection of input channel
Setting channel 0000 ~ 1111
It is used for selecting input characteristics of external analog value or pulse value.
The first part of LED (form right to left):It defines characteristics of voltage signal analog input VC1.
The second part of LED (form right to left): It defines characteristics of voltage signal analog input VC2.
The third part of LED (form right to left): It defines characteristics of current signal analog input CC.
The fourth part of LED (form right to left): It defines characteristics of pulse signal analog input PLS.
The corresponding relation is shown as fig.6-10 between input signal and setting freq.
Freq.
Freq.
Output freq.
Output freq.
[F2.9]
[F2.9]
[F2.8]
[F2.8]
Analog value Analog value

Input upper
Input lower
limit
limit
Positive character
Analog value Analog value

Input upper
Input lower
limit
limit
Negative character
Fig.6-10 corresponding relation between analog input and setting freq.
F2.11
External freq. set time constant of filtering
Setting range 0.01 ~ 1.00s
Setting freq. set by external analog input will be filtered to eliminate fluctuate. Time constant of filtering have
to appropriate set according to fluctuate of external input signal.
F2.12
Combination setting mode
Setting range0 ~ 29
The parameter is valid only when the frequency input channel F0.1 is set as 8.
50
SUNFAR C320
Setting
Value
Setting
Value
External voltageVC1 + External current CC
External voltageVC1 - External current CC
External voltageVC2 + External current CC
External voltageVC2 - External current CC
External voltageVC1 + External voltageVC2
External voltageVC1 - External voltage VC2
External voltageVC1 + pulse setting
External voltageVC1 - pulse setting
External voltageVC2+ External current CC- pulse setting
11
External voltageVC1+ panel setting - pulse setting
8
10
External voltageVC2+ External current CC+

pulse setting
External voltageVC1 + panel setting + pulse
setting
12
External voltage1 + panel setting + digital setting
13
External voltage1 - panel setting + digital setting
14
External voltage2 + panel setting + digital setting
15
External voltage2 - panel setting + digital setting
16
External current + panel setting + digital setting
17
External current - panel setting + digital setting
18
Serials interface setting + External voltage1
19
Serials interface setting - External voltage1
21
Serials interface setting - External current + pulse setting
23
Serials interface setting + External voltage2 - panel setting
20
22
24
26
28
F2.13
Serials interface setting + External current +

pulse setting
Serials interface setting + External voltage1 +
panel setting
External voltage2 + External current + panel
setting
The max of external voltage1 and external
voltage2
Nonzero valid of External voltage1and External
voltage2
Analog output selection
25
27
29
External voltage2+ External current - panel setting + digital

setting
The max among External voltage1, External voltage2 and
External current
Nonzero valid External voltage1, External voltage2 and
External current CC
It defines meaning of AO1AO2.

The first part of LED: it defines the meaning of analog output terminal AO1.
The second part of LED: it defines the meaning of analog output terminal AO2.
0Output freq.
Amplitude accumulation of AO1 and AO2 are in direct ratio to the output frequency. F2.15 and F2.17 are
corresponding to the upper limit freq.
1Output current
Amplitude accumulation of AO1 and AO2 are in direct ratio to the output current. F2.15 and F2.17 are twice
rated current of inverter.
2Output voltage
Amplitude accumulation of AO1 and AO2 are in direct ratio to the output voltage. F2.15 and F2.17 are
corresponding to [F1.4] and [F1.15].
Amplitude accumulation of AO1 and AO2 are in direct ratio to the motor rotate speed of inverter. F2.15 and
F2.17 are corresponding rotate speed that is corresponded the upper limit freq..
4PID setting
Amplitude accumulation of AO1 and AO2 are in direct ratio to the setting value of PID. F2.15 and F2.17 are
corresponding to feedback of 10.00.
5PID feedback
Amplitude accumulation of AO1 and AO2 are in direct ratio to the PID feedback. F2.15 and F2.17 are
corresponding to feedback of 10.00.
The third and fourth part of LED: Reserved.
SUNFAR C320 51
F2.14
F2.15
The lower limit of analog output AO1

The upper limit of analog output AO1
Setting range 0.0 V/0.0mA ~ [F2.15]

Setting range [F2.14] ~ 12.0 V/24.0mA
F2.16
F2.17
The lower limit of analog output AO2

The upper limit of analog output AO2
Setting range 0.0 V/0.0 mA ~ [F2.17]

Setting range [F2.16] ~ 12.0 V/24.0mA
Those parameters define the max and min value of analog output AO1and AO2, shown as fig 6-11.
AO1/AO2
[F2.15]
[F2.17]
[F2.14]
[F2.16]
Upper limit voltage Output freq.
Output current
Output voltage
Rotor speed
PID setting
10.00
10.00
PID
1
2
3
4
5
6
Rated current
The max/rated Voltage
Fig.6-11 output of analog terminals
AO1 and AO2 provide voltage signal form 0 to 12V or current signal form 0 to 24 mA. Two kinds of output
signal can be selected by JP (JP1 and JP2) switch. JP1 and JP2 are shown as fig.6-12.
JP2
1-2 shortedAO1 output voltage signal
2-3 shortedAO1output current signal
IO1
VO2
VO1
JP3
IO2
+10V
+5V
JP1 JP2 JP3
Fig.6-12 JP2/JP3 terminals
F2. 18
Reserved
6.4 Digital O/I parameter unit

F3.0
F3.1
F3.2
F3.3
F3.4
F3.5
Function selection of input terminal 1

Setting range0 ~ 25
Setting range0 ~ 25
Setting range0 ~ 25
Setting range0 ~ 25
Setting range0 ~ 25
Setting range0 ~ 25
52
SUNFAR C320
0 Control terminal is idle

1 Multi-speed control terminal 1
Combination of multi-speed control terminals is used for selecting output freq. of multi-speed.
4 Wobble freq. is valid
When F7.0 is ###2 and any of those parameters is set 4, wobble freq. is valid.
5 State of wobble freq. reset
When inverter is stop and F7.0 is ##0#, forcible reset will work by setting those parameters.
6 FWD jog control
7 REV jog control
When F0.4 is ###1 and any of those parameters is set 6 or 7, external jog signal is valid.
8 Acc& Dec time selection terminal 1
9 Acc& Dec time selection terminal 2
They are used for selecting external terminals Acc/Dec time 1~4.
10 Freq. setting channel selection 1
When F0.1 is 9, Frequency input channel is set by terminals state of 10, 11 and 12. See the explanation
about parameter F0.1.
13 Freq. is controlled gradually increase (UP)
14 Freq. is controlled gradually decrease (DW)
15 UP-DW freq. clear
When F0.3 is##0#, one of terminal X1~X6 defined by this parameter have function of forcible clear.
16 Uncontrolled stop control
If one of terminal X1~X6 defined by this parameter is connected with CM, the inverter will lock output signal
and applied motor will uncontrolled stop. Then inverter will detect speed and restart after terminal is
disconnected with CM.
17 Fault signal of peripheral equipment input
When one of terminal X1~X6 is defined by this parameter is connected with CM, peripheral equipment is fault.
The inverter will lock output signal and display FU.16.
18 Three-line mode running control
When F0.5 is 2, one of external terminal X1~X6 defined by this parameter is stop trigger switch of inverter.
See explanation about F0.5.
19 DC braking control
When inverter is stop and one of external terminals X1~X6 defined by this parameter is connected with CM
and output freq. is lower than Initial freq. of DC braking, function of DC braking is valid until terminal is
disconnected with CM. Refer to explanation about F4.4~F4.7.
20 Inner counter clear
21 Inner counter timer
Only terminal X6 is used for Inner timer, namely parameter F3.5 is 21.
22 PLC running valid
When F5.0 is ###2 and any of those parameters is set 22, PLC running is valid.
23 PID running valid
When F8.0 is ###2 and any of those parameters is set 23, PID running is valid.
24 Reserved
25 PLC state reset after stopping
If F5.0 is set as #1##, the PLC state will keep fix. But external terminals will force reset, which is set by this
function.
SUNFAR C320 53
F3.6 Output terminal OC1
F3.7 Output terminal OC2
F3.8 TA, TB and TC of relay contacts
Setting range0 ~ 18
Setting range0 ~ 18
Setting range0 ~ 18
It defines expression content of relay contact and terminals OC1 and OC 2 when collector is open-circuit.
Shown as fig.6-13.
When TA is on with TC, setting functions will be available.
While connecting the external inductance cell

(For example, Relay coil), it must connect the
parallel fly-wheel diode D.
2
Fig.6-13 Inner wiring diagram of output terminals
0In the running

When the inverter is in the running state, it will output the valid signal. While the inverter is in stop mode, it will
output the invalid signal.
1Frequency reaching
When the output frequency of inverter approaches the certain range of the setting frequency. (The range is
decided by parameter F3.9), it outputs valid signal, otherwise, outputs the invalid signal (High-resistance).
OC
High resistance
[F3.9]
f
Setting freq.
O utput freq.
O utput freq.
Fig.6-14 Freq. reaching signal
2Freq. level detection signalFDT

When the output frequency of inverter is over FDT Frequency level, the inverter will output the valid signal
(Low electrical level) after the setting delay time. When the output frequency of inverter is lower than FDT
frequency level, after the same delay time, it will output the invalid signal (High resistance).
OC1
High resistance
High resistance
Setting frequency
[F3.10]
[F3.12]
FDT Level
[F3.11]
[F3.13]
[F3.11]
[F3.13]
Fig. 6-15 Freq. level detection signalFDT
54
SUNFAR C320
3. Over-loading alarm
When the output current of inverter is over the over-loading alarm level, it will output the valid signal (Low
level) after the setting alarm delay time. When the output current is lower than the over-loading alarm level,
it will output the invalid signal (High resistance) after the same delay time.
O u tp u t c u rre n t
A la r m
le v e l
OC
H ig h r e s is ta n c e
[F 3 .1 5 ]
[F 3 .1 5 ]
H ig h r e s is ta n c e
t
Fig.6-16 Over-load alarm
4External fault halt

When the external fault input signal is valid and it will lead to stop-machine, the terminal will output the
valid signal (Low level), otherwise it will output the invalid signal (High resistance).
5Output frequency reaches the upper-limit
When the output frequency reaches the upper-limit frequency, the terminal will output the valid signal
(Low level). Otherwise, it will output the invalid signal (High resistance).
6Output frequency reaches the lower-limit
When the output frequency reaches the lower-limit frequency, the terminal will output the valid signal (Low
level). Otherwise, it will output the invalid signal (High resistance)
7Running in zero speed
Running instruction is valid and output freq. is 0, if inverter is input freq., the terminal will output the valid
signal (Low electrical level). If inverter is not input freq., the terminal will output the invalid signal ( High
resistance).
8Internal timer reaches the setting time
When the internal timer reaches the setting time, the terminal will output the valid pulse signal of 0.5 Sec
pulse widths. (Low electrical level)
9PLC stage is end of run
When simple PLC is valid and current stage is end, this port will output pulse signal with 0.5s pulse width. 10
PLC periodic is end of run
When simple PLC is valid and current period is end, this port will output pulse signal with 0.5s pulse width.
11Reserved
12Setting value of counter arrives
See the explanation about parameter F6.3.
13Designated value of counter arrives
See the explanation about parameter F6.4.
14Reserved
15Reserved
16Inverter fault
When inverter is running with fault, it will output available signal (low level).
17Restrictions on wobble freq. of the upper and lower limit freq.
When parameters setting about wobble freq. result in that running freq. is beyond the upper and lower limit
freq., this port will output available signal (lower lever). Generally, this port output high resistance.
18Reserved
SUNFAR C320 55
F3. 9 Frequency reach the checkout amplitude
Setting range0.0 ~ 20.00Hz
If output freq. of inverter is within setting value that is set in F3.9, selected terminal will output valid signal.
Shown as fig.6-13.
F3.10
F3.11
F3.12
F3.13
FDT setting 1
FDT output delay time 1
FDT setting 2
FDT output delay time 2
Setting range0.0 ~ upper limit freq.

Setting range0.0 ~ 200.0 s
Setting range0.0 ~ Setting range
The parameter is used for setting the frequency detection level. When output frequency is higher than the
setting value of FDT, after the setting delay time, terminals will output the valid signal, shown as fig.6-14.
Parameters F3.10 and F3.11 are used for setting FDT of OC1, parameters F3.12 and F3.13 are used for
setting FDT of OC2.
F3.14 Overload alarm level
F3.15 Overload alarm delay time

Setting range0.0 ~ 20.0s
If output freq. beyond the setting value set by parameter F3.14, after the setting delay time set by parameter
F3.15, terminals output valid signal, shown as fig.6-15.
F3.16
Reserved
6.5 Auxiliary running parameter unit

F4.0 Start mode
F4.1 Start frequency
F4.2 Start frequency duration
Setting range01
Setting range0.010.00Hz
Setting range0.020.0s
Those parameters are used for defining characteristics with relation to start mode, shown as fig6-17.
The explanation of F4.0 is shown as following.
0 Routine mode
It is fit for mostly load, which have not special demand.
1Detect speed and restart
It is fit for fault reset and restart occasion, or, power off and restart occasion. Inverter will judge automatically
running speed and direction of motor. Motor, which have not stop, will start up directly according to detect
result.
Start frequency It is fit for system, which is big inertia, heavy load and high start torque.
f
Decelerate stop
with no DC braking
Setting freq.
[F4.2]
[F4.1]
Free stop
t
Start
Fig6-17 Start and stop freq. output curve
F4.3 Stop mode
Setting range0 ~ 1
56
SUNFAR C320
0 Decelerate mode
Inverter will gradually decrease output freq. to 0 according to Dec time when stopping.
1 Uncontrolled stop
Inverter will output zero freq. and lock output signal when stop, so motor will uncontrolled stop.
If user needs restart motor before motor complete stop, function of detect speed and restart must be valid
when inverter is uncontrolled stop.
Start mode and stop mode is shown as fig6-16.
F4.4 Initial freq. of DC braking when stopping
F4.5 Waiting time of DC braking when stopping
F4.6 Action time of DC braking when stopping
F4.7 DC braking current when stopping
Setting range0.00 ~ 50.00 Hz

Setting range0.0 ~ 100 ( % )
It is used for setting DC braking parameters when stopping, shown as fig6-7.

When output freq. is lower than setting freq. of Parameter F4.4, inverter will lock output and start DC braking
function after waiting setting time of parameter F4.5. DC braking when stopping is invalid while F4.6 is 0.
DC braking current when stopping is the percentage of rated current of inverter. When capability of applied
motor is lower than inverter capability, please be sure to set F4.7.
F4.8 Running threshold of zero freq.
F4.9 Return different of zero freq.

Those parameters define characteristics of freq. zero-crossing.

When inverter takes analog input freq. to set freq., analog signal will fluctuate around zero to cause astable
input. Those parameters have lagging function to avoid fluctuating around zero. appropriate set.
Function of sleep and awakening will work, if those parameters are appropriate set. For example analog input
channel VC2 is shown as fig6-18.
VC input
[F2.1]
[F2.0]
Initial setting freq.

[F2.4]
Actual setting freq.
[F2.5]
[F2.5]
[F4.8]
Initial setting freq.
[F4.9]
Fig6-18 freq. zero-crossing curve
F4.10 Jog frequency
Setting range0.0 ~ Upper limit frequency
Jog running is special running method of inverter.

Whatever the initial state of inverter is stop or run, jog signal will be received. The transition form initial
running freq. to jog freq. is act according to parameters F4.21 and F4.22.
SUNFAR C320 57
Jog Acc time
[F4.21]
Jog Dec time
[F4.22]
Jog Freq.
[F4.10]
t
Jog signal
f
Jog Acc time
[F4.22]
Jog Freq.
[F4.10]
Jog Dec
[F4.21
t
Jog signal
Fig6-19 Jog running
F4.11
Acc torque level
It is used for setting permissible output level of torque current under motor acceleration state.
The restriction on torque level is set by F4.11. It is percentage of rated current of inverter. For example, F4.11
set 150% that means the max output current is 150 percentage of rated current.
When output current of inverter is beyond setting value of F4.11, inverter will prolong Acc/Dec time to inhibit
output current in setting value of F4.11. Shown as fig6-20.
f
Modified Dec time
Braking
torque
level
t
Fig6-20 Acc torque level
F4.12 Braking torque lever
It fits for occasions where demand high performance with braking torque. If setting value of parameter F4.12
is big, the Braking effect will obvious. But inverter will alarm about over voltage if inverter is not connect
braking resistance.
58
SUNFAR C320
F4.13 Motor over-load protection coefficient
The parameter is used for setting the sensitivity of thermal relay protection for applied motor. When the rated
current of applied motor doesnt match with the rated current of inverter, it can accomplish the correct heat
protection for the motor to set this parameter.
The setting value of this parameter can be set by the following formula:
[F4.13]=
Rated current of motor

Inverters rated output current
100
While one inverter parallel running with multi-motors, the thermal relay protection of inverter will be
invalid, in order to protect the motor, please install the thermal relay on inlet terminals the motor.
F4.14
Automatic voltage regulationAVR
Setting range0 ~ 2
The function of Automatic voltage regulation is to ensure the output voltage of inverter not to fluctuate with
the input voltage. When the range of fluctuation of power supply voltage is too large, and expect to motor
have the stabilized stator voltage and current, this function should be open.
0Invalid
1 Dynamic valid
2 Static valid
When user selects dynamic voltage regulation, fast dynamic voltage regulation can inhibit form increasing
current cause by DC voltage in motor deceleration. But it easy brings current resonance.
For getting good performances in vector mode, please set AVR available (F4.14 is 1 or2).
F4.15 Energy-saving running
Setting range0 ~ 1
0Valid
1Invalid
When F4.15 is 0, inverter will detect motor load automatically and real-time rectify output voltage.
Energy-saving running works high efficiency under occasions that the range of freq. is small and the range of
speed is wide.
Because of fan or pump have a specified relationship with rotate speed, it can compendiary judge load state
according output freq. Low-freq. torque curve V/F is a typical example in energy-saving running. When user
takes low-freq. torque curve (F0.1 is 1 or2), function of energy-saving running neednt valid.
F4.16 Dead time of FWD&REV
Setting time0.0 ~ 5.0 Sec
The parameter means that the duration at zero frequency when the inverter changes its running direction,
and it is shown as the following fig.6-21. FWD and REV dead time is set for the big inertia load which has
the mechanical dead zone.
Output frequency
t
[F3.10]
Fig.6-21 Dead zone between FWD and REV
SUNFAR C320 59
F4.17
F4.18
F4.19
F4.20
F4.21
F4.22
Acceleration time 2
Deceleration time 2
Acceleration time 3
Deceleration time 3
Acc time 4/Jog Acc time
Dec time 5/Jog Dec time
Setting range0.1 ~ 6000 Sec

Setting range0.1 ~ 6000Sec
Setting range0.1 ~ 6000Sec
Jog frequency has the highest priority. In any state, as long as Jog instruction is input, the inverter will
transit to run at Jog frequency according to the setting Acc and Dec time.
f
Acc/Dec terminal 1
Acc/Dec terminal 2
Acc/Dec
time 1
Acc/Dec
time 2
Acc/Dec
time 3
Fig.6-22 Acc/Dec time selection
F4.23 Modified rated of UP/DW terminals
Setting range0.01 ~ 100.00 (Hz/Sec)
It defines rate that terminals UP/DW modify setting freq. Speed of F4.23 isnt controlled by Acc/Dec time.
F4.24 Start voltage of dynamic braking
F4.25 Action ratio of dynamic braking
Setting range600 ~ 720 V

Those parameters are valid for inverter with the inner brake unit. And they define the action parameter of
inner brake unit. When inner DC voltage of inverter is higher than the start voltage of dynamic braking, the
inner brake unit will act. If inverter connects external brake resistance, DC energy of inverter will be release
by it to decline DC voltage. When DC voltage declines to the certain value ([F3.19]-50V), inner brake unit of
inverter will be off, shown as Fig.6-23.
Brake unit action ratio is used for defining the voltage on brake resistor, and the voltage on brake unit is
Voltage PWP. Duty cycle equals brake action ratio. The ratio is larger, and the energy is consumed more
quickly, at the same time, the power of brake resistor is bigger. User can set parameter according to the
resistance and power of resistor and actual brake effect.
DC
Voltage
[F4.24]
[F4.24]-50V
Brake unit acts

t
Fig.6-23 dynamic braking
F4.26 Restart after power down setting

F4.27 waiting time of restart after power down

Parameter F4.26
60
SUNFAR C320
The first part of LED

0Invalid
1 Valid
When restart after power down setting is invalid, the inverter will clear automatically all running command and
run according to new command after power on.
When restart after power down setting is valid, the inverter will save all running command and run according
to the save command after power on.
Please make sure that other equipments in system are ready before using function of restart after power
down.
Applied motor is still running when user select restart. Here, user have to select function of detect speed and
restart.
The third and fourth part of LED: reserved.
F4.28 Reserved
6.6
F5.0 Multi-speed running mode

F5.1
F5.2
F5.3
F5.4
F5.5
F5.6
F5.7
F5.8
Multi-speed frequency 1
F5.9
F5.10
F5.11
F5.12
F5.13
F5.14
F5.15
F5.16
Running time of Multi-speed1

F5.17 Running direction of PLC multi-speed

F5.18 Running direction of PLC multi-speed

Setting range0.0 ~ the upper limit freq.
Setting range0.0 ~ 6000s


Parameter F5.0 is multi-speed running mode. It is used for setting basic characteristics of multi-speed
running.
The first part of LED(form right to left)Simple PLC selection
0Simple PLC is invalid.
1Simple PLC is valid. If priority of freq. channel is permit after starting, inverter will run at simple PLC state.
2Simple PLC is conditional valid. If external X1~X6 terminals is valid (F3.0~F3.5 is set as 22), inverter will
run at simple PLC state.
Priority of freq. channel is shown as following table.
SUNFAR C320 61
Priority
High
Low
Setting freq.
1
JOG freq.
Wobble freq. running
PID output
PLC multi-speed freq.
External terminals select multi-speed freq.
Freq. setting channel selectionParameter [F0.1]
The second part of LEDSimple PLC running mode selection

0Single loop mode
The inverter will run in setting freq of the first stage and in turn output freq. of each stage according to setting
running time. If setting running time of a certain stage is 0, the inverter will skip this stage. When a cycle
operation is end of run, inverter will stop input until user input available running instrument to restart a next
cycle.
1Single loop and stop mode
Its function has an analogy with single loop mode. The difference is that output freq. is be reduced to 0 within
the given decelerate time after a certain stage is end of run and inverter will run next stage.
2Continuous loop mode
Inverter will run eight stages in turn. If the eighth stage is end of run, the inverter will run the next cycle form
the first stage.
3Continuous loop and stop mode
Its function has an analogy with Continuous loop mode. The difference is that output freq. is be reduced to 0
within the given decelerate time after a certain stage is end of run and inverter will run next stage.
4Keep the end value
Its function has an analogy with single loop mode. The difference is that inverter will run in the last stage with
non-zero speed.
5Keep the end value and stop mode
Its function has an analogy with keep the end value. The difference is that inverter will reduce the output freq.
to 0 after arriving setting value of Acc time after a certain stage is end of run and, then inverter will run the
next stage.
0Restart from the first stage freq.
When inverter is stop caused by fault or receiving stop instrument in PLC running, it will clear current running
state and restart form the first stage freq.
1Restart from running freq., which is saved before running is break
When inverter is stop caused by fault or receiving stop instrument in PLC running, inverter will restart from
running time and freq. that is saved before running is break.
2Restart from setting freq. when running is break.
When inverter is stop caused by fault or receiving stop instrument in PLC running, setting of running time and
freq. of a certain stage will be save. And inverter will restart form setting of running time and freq. the different
between mode 1 and mode 2 is initial freq. Shown as fig6-24.
The fourth part of LEDPLC save state
0Non-save after power off
It will not save PLC running state after power off. Inverter will run form the stage 1 when power on.
1Save after power off
It will save PLC running state after power off. Inverter will run form the stage 1 when power on.
62
SUNFAR C320
Freq.
Freq.
Mode 1
[F5.3]
[F5.8]
[F5.3]
[F5.14]
[F5.2]
[F5.1]
Stop
[F5.8]
[F5.13]
[F5.1]
t
[F5.9]
[F5.6]
[F5.10]
[F5.11]
[F5.5]
[F5.9]
[F5.11]
[F5.16]
[F5.16]
Mode 2
[F5.3]
Stop
[F5.8]
Instruction
[F5.1]
Each stage
OC output
[F5.9]
[F5.11]
Whole Cyc
[F5.16]
OC output
Fig.6-24 Stop mode of single circle
Fig.6-25 PLC recover running after restart
[F5.1][F5.8] Multi-speed freq.18

Those parameters are used for setting output freq. of multi-speed.
[F5.9][F5.16] Running time of Multi-speed 1~8
Those parameters are used for confirming running time of each stage.
[F5.17][F5.18] Running direction of PLC multi-speed
Those parameters are used for defining running direction of PLC multi-speed.
[F5. 17]
0 Stage 1 FWD
1Stage 1 REV
0 Stage 2 FWD
1Stages 2 REV
0 Stage 3 FWD
1Stages 3 REV
0 Stage 4 FWD
1Stages 4 REV
[F5. 18]
0 Stage 5 FWD
1Stages 5 REV
0 Stage 6 FWD
1Stages 6 REV
0 Stage 7 FWD
1Stages 7 REV
0 Stage 8 FWD
1Stages 8 REV
F5.19 Reserved
6.7 Advanced running parameter unit

F6.0 Inverter stop when motor is cut off
Setting range0 ~ 1
When F6.0 is set as 1, inverter will automatic determine whether connect with motor. When motor is
connecting with inverter, inverter will work. Or inverter will wait.
SUNFAR C320 63
Applied motor havent stop completely but it need restart, function of Detect speed
and restart (code F4.0) need set. Or it will cause inverter fault.
F6.1 Fault self-recovery time

F6.2 Interval time of fault self-recovery
Setting range0 ~ 2
F6.1 is used for resetting some faults and run again.

F6.2 defines interval time between fault starting and fault recovery. If inverter cant recover in setting value of
F6.1 it will output fault signal. Inverter will check speed and restart.
Inverter cant do self-recovery about overheat or overload protection.
F6.3
F6.4
Final value setup of internal counter

Internal timer setup

The parameter defines the counting action of internal counter, and the clock terminals of counter is selected
by parameter F1.6.
The counting value of counter for the external clock reaches the value appointed by parameter F3.5, and the
corresponding Terminal OC outputs a valid signal of same width with the external clock cycle.
When the counting value of counter for external clock reached the value appointed by Parameter F6.3, the
corresponding Terminal OC will output the valid signal, Go on counting to the value provided by parameter
F6.4, which will lead to reset and the output valid signal will be withdrawn.
The clock cycle of counter should be over 5ms and the min width should be 2ms.
[F6.3]
[F6.4]
Pluse
OC
OC
Fig.6-26 Internal counter function
F6.5
F6.6
F6.7
F6.8
Skip freq. 1
Amplitude accumulation of Skip freq. 1
Skip freq.2
Amplitude accumulation of Skip freq.
Setting range0.0 ~ upper frequency

Setting range0.0 ~ upper frequency
It is used for avoiding resonance point of mechanical load. Shown as fig. 6-27.
Adjusted setting freq.
Skip freq. 2
Skip freq. 1
Fig.6-27 Skip freq.
64
SUNFAR C320
F6.9 Linear speed coefficient setting
This parameter is used for confirming the diapaly value of running linear speed and setting linear speed, and
displaying other value being positive ratio with the output frequency.
Running linear velocityd-10= F6.9 output frequency (d-0)
Setting linear velocityd-11= F6.9 Setting frequency (d-6)
F6.10 Close-loop analog coefficient setting
PID feedback valued.9= F6.10 actual feedback value

PID setting valued.8= F6.10 setting value
F6.11 Rotator speed coefficient setting
It is used for rectifying the display value of rotator speed.

rotator speedd.3= F6.11 actual output rotator speed
F6.12 Monitor item selection 1 / Main display

F6.13 Monitor item selection 2 / Auxiliary display
Setting range0 ~ 11
Setting range0 ~ 11
This parameter is used for confirming display content of operation panel in state monitor mode.
F6.14 Query or modify parameters
Setting range: 0 ~ 9999
It is used for getting check code to query or modify parameters.

F6.15 Parameter initialization
Setting range0 ~ 2
It is used for modifying inverters parameters to manufacture setting.

0Parameter initialization is off.
1Parameter initialization is on.
2Clean fault records.
F6.16 Copy parameter function
Setting range0 ~ 1
0Forbid
It is forbidden to copy the backup data form operation panel to inverter, but this function doesnt affect the
copy and read parameter function.
1Allow
F6.17 Manufactory password
SUNFAR C320 65
Dont modify this parameter without our permission.
F6.18 User password
It is used for getting some special power for user.

F6.19 Reference password
It is always random number.
6.8 wobble freq. running parameter unit

F7.0 Wobble freq. running mode
Setting range 00001112
It is used for setting basic characteristics of wobble freq. running.

0 Function of wobble freq. is invalid.
1 Function of wobble freq. is valid.
When inverter receives running instruction, inverter will run in setting freq. of F7.1. Then inverter will in
wobble freq. running mode after arriving setting time of F7.2.
2 Function of wobble freq. is conditional valid.
When external input terminals are valid (namely one of F3.0~F3.5 is 4), the inverter will run in wobble freq.
running mode. When external input terminals are invalid, the inverter will run in preset freq. of wobble freq.
(F7.1).
The second part of LED: restart mode
0Restart according to parameters saved before stop
1Restart
The third part of LED: wobble freq. characteristicsSee explanation about parameter F7.3
0The wobble freq. is fixed
1The wobble freq. is changeable.
The fourth part of LED: Storage characteristics of wobble freq.
0It will not save the running state of wobble freq. after power off
1It will save the running state of wobble freq. after power off
F7.1 Preset freq. of wobble freq.
F7.2 Waiting time of preset freq.

Preset freq. of wobble freq. is running freq. before inverter is in or out wobble freq. mode.
When [F7.0]###1inverter will start and run in preset freq. of wobble freq., then run in wobble freq. mode
after the setting time of F7.2.
When [F7.0]###2 and the terminals of wobble freq. is valid (F3.0~F3.5 is 4)the inverter will run in wobble
freq. mode. When [F7.0]###2 and the terminals of wobble freq. is invalid, inverter will output preset freq.
[F7.1].
F7.3
Amplitude of wobble freq.
Setting range0 ~ 50.0 %
F7.3 is rate of amplitude of wobble freq.

When F7.0 is [F7.0]#0##
Amplitude of wobble freq. [F7.3]the upper limit freq. [F0.8]
When F7.0]#1##
Amplitude of wobble freq. [F7.3]Preset center freq. of wobble freq. [F7.7] + External setting freq.
66
SUNFAR C320
F7.4 Jumping freq.
Setting range0.0 ~ 80.0 %
When freq. arrives the upper limit freq. , the freq. will fast decline. Or when freq. arrives the lower limit freq.,
the freq. will fast ascend. Jumping freq. is amplitude, which freq. is ascending or declining. Shown as fig6-26.
Actual jumping freq. = [F7.4]Amplitude of wobble freq. [F7.3]
F7.5 Triangular rise time
F7.6 Triangular fall time

F7.5 defines the running time from lower limit freq. to upper limit freq. of wobble freq., namely Acc time
F7.5 defines the running time form upper limit freq. to lower limit freq. of wobble freq., namely Dec time
The sum of F7.5 and F7.6 is running cycle of wobble freq.
F7.5 and F7.6 define slope of Acc and Dec in wobble freq.
F7.7 Preset center freq. of wobble freq.
Setting range: 0.0 ~ upper limit freq.
Center freq. of wobble freq. is central value of output freq. when inverter is in wobble freq. mode. The sum
of setting value of F7.7 and F0.1 is actual center freq.
Running process of wobble freq. is shown as fig6-28.
Running freq.
Running freq.
[F7.4] Amplitude of wobble freq.
Amplitude of
wobble freq.
[F7.7]
[F7.1]
Amplitude
of wobble
freq.
Preset center freq. of wobble freq.
[F7.5]
Break in wobble
freq. and restart
[F7.1]
[F7.6]
External freq. set by [F0.1]
Running instrument
t
[F7.2]
Fig.6-28 Running process of wobble freq.
Wobble freq.
6-29 Breakpoint memory comeback
6.9 PID control parameter unit

F8.0 Inner PID control
The first part of LED(form right to left) Inner PID control

0Inner PID control is invalid
1Inner PID control is valid
2Inner PID control is conditional valid. Inner PID is set by external terminals X1X6 ( Parameters
F3.0~F3.5) .
The second part of LED PID controller selection
0 proportion
1Integral
2Proportion and integral
The third part of LED Regulating property of PID controller
0 positive interaction
1Reactor
The fourth part of LED: The pole choosing of PID controller

0: Monopole PID control
1: ambipolar PID control
Under the monopole PID control mode, the output phase sequence of inverter is mono-direction; and the
external terminal decides the direction of output that it has no relation with the output of PID controller. The
adjusting effect of PID controller only affect the output frequency of inverter. Please refer to fig 6-30.
Monopole PID control applies in water and voltage supply which do not need the setting of motors reversion.
Under the ambipolar PID control mode, when the adjusting effect of PID controller makes the output
SUNFAR C320 67
frequency as 0, and it has margin between PID setting and feedback, the output phase sequence and
motors reversion would change. That is to say, the external terminal and PID controller decide the motors
reversion together under this control mode. Please refer to fig 6-31.
PID feedback
PID feedback
Warp limit [F8.9]
warp limit [F8.9]
PID setting
Time
Time
Output frequency
Under the ambipolar
PID control mode,the
output frequency would
change the phase
sequence
Output frequency
Under monopole PID
control mode, when
output frequency reduces
to o, the direction would not
change.
Time
Fig 6-30 Monopole PID control mode
F8.1 Inner PID setting and channel selection
Time
Fig 6-31 Ambipolar PID control mode
It is used for setting inner PID and feedback channel.

The first part of LED(form right to left)It is used for setting PID channel
0Digital setting. It is set by parameter F8.2.
1Serials interface setting
2Panel potentiometer setting, it is on the operation panel.
The second part of LED Reserved.
The third part of LED It is used for setting PID feedback channel.
0External voltage input VC1 is as feedback channel, which is in the range of 0~5V.
1External voltage input VC2 is as feedback channel, which is in the range of 0~10V.
2External current input CC is as feedback channel, which is in the range of 0~20mA.
3Pulse input PLS is as feedback channel, which is in the range of 0~50KHz.
4VC1+CC
Feedback value is composed of VC1 and CC.
5VC1-CC
Feedback value is that VC1 minus CC.
6Min (VC1, CC) Feedback value is min value between VC1and CC.
7Max (VC1, CC) Feedback value is max value between VC1and CC.
Reserved.
F8.2 Inner PID close-loop digital setting
Setting range0.0 ~ 10.00V
If F8.1 is 0#00, setting value will be set by F8.2.

F8.3
F8.4
F8.5
F8.6
Minimum fixed value

Maximum fixed value
Feedback of minimum fixed value
Feedback of maximum fixed value
Setting range0.0 ~ [F8.4]

Setting range[F8.3] ~ 10.00
Parameters F8.3 and F8.4 define the upper and lower limit value of PID setting. Parameters F8.5 and F8.6
define corresponding relation with PID feedback value. Shown as fig.6-32.
68
SUNFAR C320
Expected feedback value
[F8.6]
[F8.5]
PID setting value
[F8.3]
[F8.4]
Fig.6-32 Relation between PID fixed value and expected feedback value
F8.7 Proportion gain

F8.8 Integral time constant

Those parameters are inner parameters of PID.

F8.9
Allowable deviation limit
Setting range0.0 ~ 20.0(%)
The parameter is the allowable deviation value relative to the setting max value. When the difference
between feedback value and the setting value is lower than this setting value, PID controller will stop. Shown
as fig.6-33.
This function is mainly suited for the system that has lower control precision and needs to avoid adjusting
frequently, for example, water-supply with constant pressure system.
f
PID action
PID feedback
[F8.9]
PID setting
PID action
Fig.6-33 PID Control allowable deviation limit
F8.10 Preset freq. for close-loop

F8.11 Holding time of preset freq. for close-loop

Those parameters define freq. and running time of inverter before actual PID control is valid. In some control
systems, inverters will forcible output a certain freq. (F8.10) and keep it in setting time (F8.11) for controlled
object arrives fast targeted value. When controlled object almost arrives targeted value, PID controller will
be valid to improve response speed.
F8.12 long-distance manometer range
Setting range0.00120.000Mpa
It defines measuring range of long-distance manometer, user have to input it.

F8.13 Sleeping threshold
Setting range: 0.0 ~ 10.0
It defines feedback value while inverter goes sleep state. When actual feedback value is bigger than setting
value and inverter arrives lower limit value, the inverter will go sleep.
F8.14 Reserved
SUNFAR C320 69
6.10
Communication function parameter units
F9.0 Communication setting
The first part of LED(form right to left) It is used for setting baud rate of serials communication.
0 Reserved
11200bps
2: 2400bps
3: 4800bps
4: 9600bps
5: 19200bps
To make sure both sides have the same baud rate, when client use serials communication.
The second part of LED To set data format of serials communication.
0Close
1 Even
2Odd
To make sure both sides have the same data format, when client use serials communication.
F9.1 Local address
Setting range0 ~ 30
F9.2 Response delay of local
Setting range0 ~ 1000 ms
It defines waiting time, which is the time, receiving local correct code to send response data frames.
F9.3 Function setting of communication Auxiliary function

0 The inverter is slave
1 The inverter is master
The second part of LED Act selection after communication is lost
0 Stop
1Keep
F9.4 Checkout time of communication overtime
Setting range0.0 ~ 100.0 Sec
If the local doesnt receive correct data signals in regulate time, the communication is fault. Inverter will keep
on running or stopping according to setting of parameter F9.3.
F9.5 Linkage setting proportion
F9.6 Rectify channel of linkage setting proportion

Setting range 0 ~ 4
It is used for setting proportion of output freq. between master and slave, when takes linkage setting control.
When F9.6 is 0, rectify channel of linkage setting proportion is invalid.
Slave freq. = Master freq. [F9.5]
When F9.6 is 1, 2,3 or 4, rectify channel of linkage setting proportion is valid.
Slave freq. = Master freq. [F9.5]value of rectify channel or the max value of rectify channel
F9.6 is used for selecting rectify channel.
Rectify channel 1Panel potentiometer
Rectify channel 2External voltage signal VC10 ~ 5V
Rectify channel 3External voltage signal VC20 ~ 10V
Rectify channel 4External current signal CC0 ~ 20mA
F9.7 Reserved
6.11 Special function parameter unit

FC.0 Under voltage protection level
Setting range
360V ~ 460V
70
SUNFAR C320
It defines lower limit voltage which terminals P+ and P- are allow while inverter is working normally. For some
low voltage conditions, user can decrease under voltage protection level to ensure that inverter is running
normally.
FC.1 Over voltage limit level
Setting range
660V ~ 760V
It defines threshold of voltage stall protection while motor is decelerating. If DC voltage caused by
decelerating is beyond setting value of FC.1, deceleration time will automatic prolong. Shown as fig6-35.
f
Adjust Dec time
DC voltage
[FC.1]
t
Fig.6-35 voltage stalls protection in Dec speed
FC.2
Current amplitude limiting level
It defines the max output current that is inverter permit. Whatever the operation mode is, inverter will adjust
output freq. to inhibit current within the range of regulation, when output current of inverter is beyond setting
value of FC.2.
FC.3
Reserved
FC.4
Running protection function setting
It is used for setting some coefficients with special function in running process. Generally, user neednt set.
The first part of LED(form right to left) Under voltage compensation intensity
The second part of LED Over voltage inhibit intensity
The third part of LED Over current inhibit intensity
The fourth part of LEDSelf-adapting braking torque adjust intensity
FC.5
Action function selection
Setting range
0000 ~ 0111
The first part of LED(form right to left) Cooling fan control

0Cooling fan run after inverter run.
Cooling fan will stop after inverter stop. When temperature is above 40the cooling fan also will also run.
1Cooling fan will automatic run when inverter is power on.
The second part of LED Variable speed control of cooling fan
0Invalid
1Valid
Cooling fan always keep the max speed.
The third part of LED Voltage over modulation
0Invalid
1Valid
FC.6
Function setting
Setting range
0000 ~ 0011

SUNFAR C320 71
0invalid
1Valid
Parameter F0.18 will invalid and user can modify all parameters. If user want to get new password, please
refer to our.
The second part of Le define active level of external control terminals
0It is valid when terminals are close.
1It is valid when terminals are open.
The third and fourth part of LEDReserved.
FC.7
Reserved
FC.8
Agency password
FC.9
FC.10
FC.11
Setting range
Rotate speed coefficient

Gain of closed loop of rotate speed
Integral time constants of closed loop of rotate speed
0~ 9999

They are closed loop control parameters about rotate speed and used for setting arithmetic of vector control.
Generally, they need modify by professional person.
FC.12
Compensation rectify of dead zone
Setting range0 ~ 25
It is read-only parameter for user. Rectify coefficient of dead zone can be modify by parameter F1.20 only.
FC.13
Program version
Range2100 ~ 2199
It is read-only parameter.
72
SUNFAR C320
7. FAULT DIAGNOSIS AND COUNTERMEASURES

7.1 Protective functions and Countermeasures
Code
Faults
Probably Cause
1. Acceleration time is too short.
2. V/F curve is not suitable.
Fu.1
Over-current during 3. User start rotating motor, but doesnt set function
Acc
of detect speed and restart.

4. Value of torque boost set too high.
5. Mains voltage is too low
Fu.2
Fu.3
Over-current during
Dec
Deceleration time is too short.
Over-current during 1. Load occurs mutation

running or stopping 2. Mains voltage is too low
Solutions
1. Prolong the acceleration time
2. Descend the torque boost or adjust
the V/F curve
3. To set function of detect speed and
restart
4. To decrease voltage of torque boost
5. Check mains voltage
Prolong the deceleration time
Decrease load fluctuation
1. Check power supply
Fu.4
Over-voltage during 1.Input voltage is too high
2. To decrease setting value of F4.11
Acc
3. Control the on-off of inverter by the
2. Power supply is switched on or off frequently.
control terminal
Fu.5
Fu.6
Fu.7
Fu.8
Over-voltage during 1. Deceleration time is too short.

Dec
2. Input-voltage is abnormal
1. Extend the deceleration time

2. Check power supply voltage
3. Install or select the brake resistance
Over-voltage during 1. Power supply is abnormal
running
2. There are energy feedback load
2. Install or select brake resistor
Power supply is abnormal
Check power supply voltage
Under-voltage
1. Power supply is abnormal
1. Check power supply voltage
during running
2. There is great fluctuation of load in electric network.
2. Provide the power supply separately
Inverter protective
1. Output is short-circuit or ground
2. Reduce the load
action
2. Load is too heavy
3. Check whether brake resistor is
Over voltage at
stop
1. Check wiring
Fu.9
short-circuit
1.The output terminal of inverter grounds
Fu.10 Output ground
Fu.11 Interfere
1. Check the connecting wire
2. The wire is too long between inverter and motor and the 2. Shorten the connection wire or reduce
carrier frequency is too high.
the carrier frequency.
Faultaction causing by electromagnetism interfere
Add absorb circuit

1. Reduce the load or replace with
Inverter
Fu.12
over-loading
1. Load is too heavy.
higher capacity inverter.
2. Prolong Acc time.
3. Torque boost is too high or V/F curve is not suitable.
3. Decrease the torque boost or
4. Voltage of Power supply is too low
adjusting V/F curve.
5. User starts rotating motor, but doesnt set
4. Check Voltage of Power supply
function of detect speed and restart.
5. To set function of detect speed and

restart
SUNFAR C320 73
Code
Faults
Probably Cause
Solutions
1. Reduce the load
Fu.13 Motor over-loading
1. Load is too heavy.
2. Prolong Acc time
3. Increase the over-loading protection
3. The setting of protection factor is too small
factor of motor [F4.13]
4. Torque boost is too high or V/F curve is not suitable.
4.Decrease torque boost voltage and

adjust V/F curve.
1. Clear air duct or improve the air
Fu.14 Inverter overheat
1. Wind hole is blocked
condition.
2. Environmental temperature is too high
2.Improve ventilation condition
3. Fan is damaged
or decrease carrier frequency.

3. Replace fan.
Fu.15 Reserved
Peripheral
Fu.16
There is signal input on the peripheral. Equipment fault
equipment
Check the signal source and the
input terminal of Inverter
occur error
pertinent equipments
Fu.17 Inverter output lack Inverter output lack phase
Check the wire of applied motor.
Fu.18 Reserved
Main contactor of
Fu.19 inverter is poor
contact
Fu.20
2. Replace contactor
3. Starting resistance id damaged.
3. Replace starting resistance.
4. Control circuit is damaged.
4. Contract Us
1.The current detecting equipment or circuit is damaged
error
2.Auxiliary power supply has problem
Temperature
occur faults
Fu.29
2. Contactor is damaged.
Current detecting
Fu.21 sensor
Fu.22-
1. Power supply is too low
Contract Us
1. Signal line of temperature is poor contact
1. Check jack
2. Temperature sensor is damage.
2. Contract Us
Reserved
7.2 Fault record inquiry

C320 series inverter records the last six fault codes and the output parameters of last fault. This information
is aid in looking up the fault causes. Fault information and state monitor parameters are stored uniformly, so
please refer to the operation way to look up the information.
Monitor
Item
Contents
Monitor
Item
Contents
Monitor
Item
Contents
d-26
First fault record
d-30
Fifth fault record
d-34
Output current of last fault
d-27
Second fault record
d-31
Sixth fault record
d-35
Output voltage of last fault
d-28
Third fault record
d-32
Output frequency of last fault
d-36
DC voltage of last fault
d-29
Fourth fault record
d-33
Setting frequency of last fault
d-37
Module temperature of last fault
74
SUNFAR C320
7.3 Reset
Be sure to check the fault cause and exclude it before reset, otherwise, which may
lead to the inverter, the permanent damaged.
If the inverter can not be reset or occur the fault again after reset, please find out the
reason. Continuous reset will damage the inverter
Over-load or over-heat protective action should delay 5 minutes to reset.
When the inverter happens to the fault, you can reset the inverter to resume the normal
running by any way as follows:
I.
External reset input-terminal RST and CM terminal are closed, then off.
II. While the fault code is displayed, press
key.
III. Turn the power source off.
IV. It will send fault reset instrument by RS485 interface.
SUNFAR C320 75
8MAINTENANCE
As a result of ambient temperature, humidity, dust, vibration and aging of internal components of inverter, the
inverter will probably appear the potential problem during running. In order to ensure the inverter to run
steadily for a long time, the inverter should be checked up once at 3 or 6 months.
First of all, turn the inverters power off. And professional worker performs maintenance.
8.1 Daily Maintenance

Maintenance points
Inspection
Time
items
Daily
Criterion
contents
1.Temperature,
Running
Environment
1.When temperature is over 40, the panel should be opened.
Humidity
Humidity is less than 90%, and no condensation
2.Dust, gases
2. No peculiar smellno flammable and explosive gases.
1.Installation
1. Installation environment is well ventilated, and the duct is not
Cooling system
Inverter
Inspection
Periodic
Environment
blocked.
2. Fan in inverter
2. Fan is normal and no abnormal voice.
1.Vibration,
1. Vibration smooth, the temperature of air outlet is normal.
Temperature raise
2. Not abnormal voice and no peculiar smell
2. Noises
3. Fastening screw is not loosed.
1.Vibration,
Motor
Temperature raise
2. Noises
Input/output
Parameters
1. Running smooth, and temperature is normal

2. No abnormal and smooth noises.
1. Input voltage
1. Input-voltage is in the setup range
2. Output current
2. Output-current is under the rated value
Input voltage
Moving-coil voltmeter
Output voltage
Rectifier-type voltmeter
O/I current
Tong-type ammeter
Inverter has done the electric insulating experiment before leave-factory, so user dont need to do the
withstand voltage test.
Do the insulation test to the inverter if necessary, all of I/O terminals must be connected in short-circuit (R,
S, T, U, V, W, P, P-, PB). Strictly prohibited from doing the insulation test for the single terminal. Please use
500V Meg-ohmmeter to perform this test.
Control circuit can not be used the Meg-ohmmeter to test.
For insulation test to motor, the connection wire between motor and inverter should be disassembled.
76
SUNFAR C320
8.2 Damageable parts maintenance

Some cells in inverter are worn out or the performance descends in the process of usage process, in order to
ensure the stable running of inverter, so the inverter needs to do the preventative maintenance or replace the
part if necessary.
Filter capacitor
Pulse current in main circuit will take effect on the performance of aluminum electrolytic filter capacitor, and
the degree of effect has relation with the ambient temperature and usage condition. In normal condition, the
electrolytic capacitor of inverter should be replaced at 4 to 5 years.
When the electrolytic capacitor leaks out, safety valve falls out or main block of capacitor expands, the
corresponding parts should be replaced immediately.
Cooling fan
The lifetime of all the cooling fans in the inverter is about 15000 hours (that inverter is used continuously
about two years). If the fan occurs the abnormal noise or vibration, it should be replaced immediately.
8.3 Storage
If the inverter isnt used for a long time, please notice the following items:
(1) To avoid storing the inverter at the environment with high-temperaturehumidity, vibration or metal dust,
and ensure the well ventilation.
(2) If the inverter is not used for a long time, it should be energized to resume the capability of electrolyte
capacitor once at 2 yearsat the same time, check the functions of inverter. When the inverter is electrified,
its voltage should be increased by an autotransformer step by step and the time should not be less than 5
hours.
If inverter is not used for a long time, the performance of internal filter capacitor will descend.
8.4 After sale services
Guarantee time of this inverter is 18 months (From the day of purchase). In guarantee time, if the inverter
occurs fault or be damaged in normal usage, our company will provide the free repair service or replacement.
Guarantee scale is just the mainframe of inverter.
In guarantee time, if the faults are caused by the following cases, certain service cost would be charged.
Malfunction is caused by not following the operation manual or over using the standard specification;
Malfunction is caused by repairing without admision.
Malfunction is caused by the bad-storage.
Malfunction is due to application of inverter for abnormal functional needs.
Damage is caused by fire, salt-corrode, gas-corrode, earthquake, storm, flood, lightning strike, voltage
abnormal or other force majored.
Even if over guarantee time, our company will provide the paid service forever.
SUNFAR C320 77
9. USAGE EXAMPLE
9.1 Panel on-off control, Panel potentiometer setting frequency and V/F control
9.1.1 Parameters setting
1. When F0.0 is 0, V/F method is valid.
2. When F0.4 is 00#0, panel control is valid.
3. When F0.1 is 3, panel potentiometer is valid.
9.1.2 Basic wiring
Power
Supply
3-phase Breaker
Motor
U
V
W
E
R
S
T
FWD
Direction
Control
CM
Voltmeter (0~10V)
AO1
AO2
GND
Voltmeter (0~10V)
Fig9-1 Basic wiring
9.1.3 Operation
Press
key to start the inverter, and then rotate the button of panel potentiometer in clockwise to
increased setting frequency step by step. Contrarily, rotate in anti-clockwise to decreased setting frequency
step by step.
Press
key to stop the inverter.
External control terminal FWD decides the running direction of motor.
9.2 External control mode, external voltage setting frequency and V/F control
2. When F0.4 is 00#1, external terminals control is valid.
3. When F0.1 is 5, external voltage VC20~10Vis valid.
9.2.2 Basic wiring
Power
Supply
3-phase Breaker
FWD
FWD
REV
REV
CM
VS
VC1 (0~5V)
10K
VC2 (0~10V)
GND
U
V
Motor
W
E
AO1
AO2
Voltmeter0~10V
Voltmeter0~10V
GND
Fig9-2 Basic wiring
78
SUNFAR C320
9.2.3 Operation
FWD-CM is offthe motor will running forward. REV-CM is off, the motor will running backward. FWD-CM and
REV- CM are off or on at the same time, the inverter will stop.
Setting frequency is set by external voltage signal VC2.
Control method of terminals FWD and REV is set by parameter F0.5.See the explanation
about parameter F0.5.
9.3 Multi-speed running, external control mode and V/F control

2. When F0.4 is 00#1,external terminals is valid.
3. To set external terminals X1, X2 and X3 as multi-speed terminals.
(Namely, parameter [F3.0]~[F3.2])
4. To set running freq. of each stage according to user needs.namely, parameter[F5.1]~[F5.7]
9.3.2 Basic wiring
Power
Supply
3-phase Breaker
R
S
T
FWD
FWD
REV
REV
CM
Multi-speed
Control
terminals
U
V
W
E
X1
X2
X3
Motor
AO1
AO2
GND
Voltmeter0~10V
Voltmeter0~10V
Fig9-3 Basic wiring
9.3.3 Operation
FWD-CM is offthe motor will running forward. REV-CM is off, the motor will running backward. FWD-CM and
REV- CM are off or on at the same time, the inverter will stop.
If X1, X2 and X3 are all opened with CM, the multi-speed running is invalid. The inverter will run as the setting
instruction speed. (The setting frequency channel is selected by parameter F0.1)
If one terminal or all of X1, X2 and X3are connected with CM terminal, the inverter will run as the multi-speed
frequency selected by X1, X2 and X3.
9.4 Panel on-off controlPanel potentiometer setting frequency and linkage control
with inverters
Master setting
1. Freq. setting channel is panel potentiometer mode. Namely F0.1 is 3.
2. Operation channel selection is panel control, namely F0.4 is 00#0.
3. Communication setting (Parameter F9.0) is default.
4. If F9.3 is 0001, the inverter is master.
Slave setting
1. Freq. setting channel is RS485 interface. Namely F0.1 is 2.
2. Operation channel selection isRS485 interface. Namely F0.4 is 00#2.
3. Communication setting (Parameter F9.0) is default.
4. If F9.3 is 0000, the inverter is slave.
SUNFAR C320 79
5.
6.
Linkage setting proportion (Parameter F9.5) will be set by user needs.

Rectify channel of linkage setting proportion is external voltage signal VC1. Namely F9.6 is 2.
9.4.2 Basic wiring
Power
Supply
3-phase Breaker
Motor
U
V
R
S
T
W
E
Host
A
RS485
B
3-phase Breaker
Power
Supply
Motor
U
V
R
S
T
Guest
VS
VC2
GND
A
RS485
B
3-phase Breaker
Power
Supply
Motor
U
V
R
S
T
Guest
VS
VC2
GND
A
RS485
B
Fig9-4 Basic wiring
9.4.3 Operation
Running freq. of slave has a certain proportion with masters. Linkage setting proportion is set by parameter
F9.5.
In this example, freq. proportion of master and slaves can get across by VC1 channel.
80
SUNFAR C320
AppendixRS485 COMMUNICATION PROTOCOL

1 Summary
C320 series of inverter provides RS485 interface, user can carry out centralized monitoring through PC/PLC
to get operating requirements. The protocol in this appendix is designed for the above functions.
1.1. About protocol
This serial communication protocol defines the transmission information and use format in the series
communication and it includes master-polling (or broadcasting) format, master coding method and the
content includes function code of action, transferring data and error checking. The response of slave is
the same structure, and it includes action confirmation, returning the data and error checking etc. If slave
takes place the error while it is receiving the information or cannot finish the action demanded by master,
it will send one fault signal to master as a response.
1.2. Application scope
1.2.1. Application products
The protocol is fit for all sunfar series of inverters, for example E380 series of inverter, C300 series of inverter
and C320 series of inverter.
1.2.2. Application methods
1 The inverter will be connected into a Single-master Multi-slave PC/PLC control net with RS485 bus.
2 The inverter will be connected into a Point to Point PC/PLC monitor background.
2 BUS structure and protocol description

2.1. Bus structure
1Interface mode
There provide RS485 interface and RS232 interface, but RS232 interface need the level translation
accessories.
2Transmission mode
There provide asynchronous series and half-duplex transmission mode. At the same time, just one can send
the data and the other only receives the data between master and slave. In the series asynchronous
communication, the data is sent out frame by frame in the form of message.
3Topological mode
In Single-master system, there are 32 sites at most. There are one master site and 31 slave sites among
these sites. The address range of slave is 0~30, 31 (1FH) is broadcast communication address. The address
of slave must is exclusive in the network. Point to point mode is a special application of single master and
multi-slaves mode. That is one condition of one slave machine.
2.2. Protocol description
C320 series inverter communication protocol is a kind of serial master-slave communication protocol, in the
network, only one equipment, and master can build a protocol, (Named as Inquire/Command). Other
equipments, slaves response Inquire/Command of master only by providing the data or doing the action
according to the masters Inquiry/Command. Here, master is Personnel Computer, Industrial Machine or
Programmable logical controller, and the slave is inverter. Master not only visits some slave, but also sends
the broadcast information to all the slaves. For the single master Inquiry/Command, all of slaves will return
a signal that is a response; for the broadcast information provided by master, slave needs not feedback a
response to master machine.
2.2.1. Data format
3 kinds of data transmission format are optional:
1 bit start-bit, 8-bit data bits, 1 bit stop-bit and no check bit.
1 bit start-bit , 8-bit data bits, 1 bit stop-bit and odd check.
1 bit start bit , 8-bit data bits, 1 bit stop bit and even check. It is also manufacture setting.
2.2.2. Baud rate
SUNFAR C320 81
There are five kinds of baud rate, 1200bps, 2400 bps, 4800 bps, 9600 bps and 19200 bps.
2.2.3. Communication mode
1 Point to point communication mode, which is master Polling and slave Responding.
2 Setting the serial interface communication parameters by the keypad of inverter. These parameters
include local address, baud rate and data format.
Master must be set the same baud rate and data format with the inverter.
2.2.4. Communication rule

1 There are at least 5-byte startup interval time between data frames, only the message with the stated
startup internal time is valid.
2 Master hand-in-hand waiting time and inverter longest response time are 8-byte transmission time.
Over this time, the communication will be determined as a failure.
3 If inverter doesnt receive any message during setting time of F9.4, it will be occurred the wire-break
fault. Running state of slaves is decided by setting value of F9.3.
2.3. Message structure
The length of each message is between 11 and 18 bytes. The type of character are ASC code and hex.
1
3800H is shown as ASC code.
Data list
10
11
12
Setting
Setting
Setting
Setting
Data
Data
Data
Data
33
38
30
30
10
11
12
Setting
Setting
Setting
Setting
Data
Data
Data
Data
38
00
DataASC
2
3800H is shown as hex.

Data list
DataHex
2.3.1.
Master command frame

Sending Sequence
0
1
2
3
4
5
6
7
8
Definition
Header
Slave addr.
Slave addr.
Slave addr
Type of order
Operation order
Order area
Operation order
Type of data
Data addr.
Data addr.
Addr. area
Sending Sequence
9
10
11
12
13
14
15
16
17
Definition
Setting data
Setting data
Setting data
Data area
Setting data
Check sum
Check sum
Check sum
Check area
Check sum
Tail
0DH
82
SUNFAR C320
2.3.2
Slave responding frame

Sending Sequence
Definition
Sending Sequence
Definition
0
Header
9
Running data
1
Slave addr.
10
Running data
Slave addr.
Data area
2
Slave addr
11
Running data
3
Slave responding
12
Running data
4
Operation order
13
Check sum
Responding area
5
Operation order
14
Check sum
Check area
6
Type of data
15
Check sum
7
Data addr.
16
Check sum
Address area
8
Data addr.
17
Tail
0DH
2.4. Message data code
2.4.1. Header
This communication protocol defines that both 2AH (ASC code of character * ) and 5AH are available.
When header is 2AH, all of data behind header is ASC code. When header is 5AH, all of data behind
header is hex code and invalid byte fill 0. Unaided headers of 2AH and 5AH arent rightful header. There
need waiting time above five bytes before sending header.
2.4.2. Slave address
Slave address is inverter address. The address range of slave machine is 0~30, 31 (1FH) is broadcast
communication address.
2.4.3. Type of order
Type of order is only in master command frame and defines task of the data in this frame. Length of each
frame is different according to different order. Type of order is shown as following table.
Data
Operation
Read the state and information of slaves
Read the running parameter of slaves
Read code parameter
Modify code parameter in RAM, it will not save after power down
Send control order
Modify code parameter in EPROM, it will save after power down
6F
Reserved
2.4.4. Operation order

Master gives a control order to slaves. It exists in all messages and is shown as following table.
Data
Operation
Data
Operation
00H
Invalid instrument
10H
To set running freq. of slave
01H
Start with FWD
11H
Start with FWD and setting freq.
02H
Start with REV
12H
Start with REV and setting freq.
03H
Stop
13H
Stop with Start setting freq.
04H
Slave will FWD running when jog
14H
Slave will FWD running with setting freq. when jog
05H
Slave will REV running when jog
15H
Slave will REV running with setting freq. when jog
06H
Jog running is stop
16H
Slave will JOG running with setting freq.
20H
Slave will fault reset
30H
Reserved
21H
Slave will emergency stop
31H
Reserved
SUNFAR C320 83
When user need not send operation order, please send invalid order 00H.
2.4.5. Slave responding

Slave responding exists in all messages and is shown as following table.
Data
0
Definition
Data
Slave receive data and works well
Definition
Data received form master is beyond the permission
range
When slave is running, data cant be modified
To try read and write parameter
If modify the data, please input password

Reserved
Appointed code or addr. Is invalid
It exist invalid ASC code in message
Type of order or operation order is invalid
9F
Reserved
When data of slave responding is 6, 7 or 8, length of responding frame is 11 bytes.
Its frame format is shown as following.

Slave
responding
Header
Slave
address
Definition
Slave
Slave
address responding
Slave address
10
Check
Sum
Check
Sum
Check
Sum
Check
sum
Tail
Order/responding area
Check area
0DH
2.4.6. State feedback

Slave gives a running state about slave to master, and state feedback exists in all messages. It is shown as
following table.
Data
00H
Operation
DC voltage of slave is not ready
Data
10H
Operation
Reserved
01H
Slave is FWD running
11H
Accelerating with FWD
02H
Slave is REV running
12H
Accelerating with REV
03H
Slave is stop
13H
Abruptly stop and restart
04H
Slave will FWD running when jog
14H
Decelerating with FED
05H
Slave will REV running when jog
15H
Decelerating with REV
06H
Reserved
16H
Slave is in DC braking state.
20H
Slave is in fault state
21H
Slave is emergency
When slave occurs fault (data of state feedback is 20H), the seventh and eighth of feedback rata frame is
fault code.
2.4.7. Check sum

The sum of ASCor hex form slave address to setting data (running data) is check sum.
2.4.8. Tail: 0DH is hex, namely ASCof CR is 0DH.
When header, tail and check sum in message occur fault form master, slave may be not responding.
84
SUNFAR C320
3.
Description about frame format
1Order is read state and information about slaves

0
1
Master
Slave
Sending Header
addr.
Slave
addr.
Operation Operation
order
order
Data
Type
Check
Sum
Slave responding
10
11
12
Header
Character information
Slave addr.
10
Slave addr
Tail
Sending Sequence
0
2
13
Check Check Check

Sum
Sum
Sum
Slave responding
11
12
State feedback
13
Check sum
State feedback
14
Check sum
Data type
15
Check sum
16
Check sum
Character information.
17
Tail
Slave will give different character information to master according to different data type in master message.
Data Type (master sending)
Character information (slave responding)
0
1
2
3
4F
Read slave inf. about

inverter model
inverter series
program version
10
11
12
Voltage level
Power
Power
Power
Power
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Master
Setting freq. of
control information
control
master
Reserved
For example, if data type is 0, slave return 400185. 4 means voltage level.
0 means Character information. 0185 means power, 18.5Kw.
2Orderis used to read running parameter of slave
Master
Sending Header
Slave
Slave
addr.
addr.
3
1
Operation Operation
order
order
6
0
Data
Data
subentry subentry
Slave responding
10
11
12
Check Check Check Check

Sum
Sum
Sum
Sending Sequence
Header
Running data
Slave addr.
10
Running data
Slave addr.
11
Running data
Slave responding
12
Running data
State feedback
13
Check sum
Sum
13
Tail
SUNFAR C320 85
5
State feedback
14
Check sum
15
Check sum
Data subentry
16
Check sum
Data subentry
17
Tail
Data subentry is state monitor parameters, shown as following table.

Monitor item
Data subentry
Returning data form slave
d-0
00
Output frequent
d-1
.
.
d-15
.
..
d-37
01
.
..
15
.
..
37
Output current
.
..
External pulse input
.
..
Temperature of module of last fault
See the explanation about state monitor parameter in the fourth chapter.
3Order is read parameter of code.

0
Master
Sending Header
Slave
addr.
Slave
addr.
Operation Operation Data

order
order
type
Data
Addr.
Data
Addr.
Slave responding
10
11
12
Check Check Check Check

sum
sum
sum
sum
Sending Sequence
Header
Parameter data
Slave addr.
10
Parameter data
Slave addr
11
Parameter data
Slave responding
12
Parameter data
State feedback
13
Check sum
State feedback
14
Check sum
Data type
15
Check sum
Data addr.
16
Check sum
Data addr.
17
Tail
Data type and data address are defined in order and .
4order is used to modify parameter of code in RAM.

order is used to modify parameter of code in EPROM.
13
Tail
86
SUNFAR C320
Sending Sequence
Master Sending
Header
Setting data
Slave addr.
10
Setting data
Slave addr
11
Setting data
3 or 5
12
Setting data
Operation order
13
Check sum
Operation order
14
Check sum
Data type
15
Check sum
Data addr.
16
Check sum
Data addr.
17
Tail
Slave responding
Sending Sequence
Header
Setting data
Slave addr.
10
Setting data
Slave addr
11
Setting data
Slave responding
12
Setting data
State feedback
13
Check sum
State feedback
14
Check sum
Data type
15
Check sum
Data addr.
16
Check sum
Data addr.
17
Tail
Data type is shown as following table.

Parameter unit
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FC
FE
FF
FH
FL
FP
Data type
For example, data address of F0.8, F1.8 and F#.8 are 8. But data type of them is different.
AttentionWhen slaves dont accomplish order form master, setting data is 0000.
5Orderis used to send control order.
It is fit for routine operation for inverter.
Master Sending
Header
1
2
Sending Sequence
Setting data
Slave addr.
Setting data
Slave addr
10
Check sum
11
Check sum
Operation order
12
Check sum
Operation order
13
Check sum
Setting data
14
Tail
Slave responding
Sending Sequence
Setting data
Header
Running data
Slave addr.
10
Running data
Slave addr.
11
Running data
SUNFAR C320 87
3
Slave responding
12
Running data
State feedback
13
Check sum
State feedback
14
Check sum
15
Check sum
Monitor item
16
Check sum
Monitor item
17
Tail
Setting data in master sending is setting freq., which is send form master to slave.
Setting data in slave responding is running parameter, which is send form master. It is set by parameter
F6.12.
Refer to the explanation about list of parameter in chapter five.
4. Usage example
4.1. Order
To read slave model of 0#.
master will send
2A 30 30 30 30 31 30 30 30 30 31 38 31 0D
5A 00 00 00 00 01 00 00 00 00 00 00 01 0D
Slave will respondInverter with 380V and 2.2KW4
2A 30 30 30 30 31 30 34 30 30 30 32 32 30 32 34 39 0D
5A 00 00 00 00 01 00 04 00 00 00 00 22 00 00 00 27 0D
4.2. Order
To read running parameter of 0# slavenamely read d.0, output freq.
master will send
2A 30 30 31 30 31 30 30 30 30 31 38 32 0D
5A 00 00 01 00 01 00 00 00 00 00 00 02 0D
Slave will respondSetting freq. is 9.99Hz
2A 30 30 30 30 31 30 30 30 33 45 37 30 32 36 30 0D
5A 00 00 00 00 01 00 00 00 00 00 03 E7 00 00 00 EB 0D
4.3. Order
To read code parameter of 0# slavenamely parameter F0.1
master will send
2A 30 30 32 30 31 30 30 31 30 31 38 34 0D
5A 00 00 02 00 01 00 00 01 00 00 00 04 0D
Slave will respondsetting freq. of RS485 input channel
2A 30 30 30 30 31 30 30 31 30 30 30 32 30 32 34 34 0D
5A 00 00 00 00 01 00 00 01 00 00 00 02 00 00 00 04 0D
4.4. Order
To modify code parameter of 0# slave (modify parameter F4.0)
master will send(To set detect and restart mode)
2A 30 30 33 30 31 34 30 30 30 30 30 31 30 32 34 39 0D
5A 00 00 03 00 01 04 00 00 00 00 00 01 00 00 00 09 0D
Slave will respond(Parameter is de modified)
2A 30 30 30 30 31 34 30 30 30 30 30 31 30 32 34 36 0D
5A 00 00 00 00 01 04 00 00 00 00 00 01 00 00 00 06 0D
4.5. Order
88
SUNFAR C320
To modify parameter F2.10 of slave as 0010

master will send
2A 30 30 35 30 31 32 30 3A 30 30 31 30 30 32 35 33 0D
5A 00 00 05 00 02 01 00 0A 00 00 01 00 00 00 01 03 0D
Slave will respond(Parameter is de modified)
2A 30 30 30 30 32 31 30 3A 30 30 31 30 30 32 34 3E 0D
5A 00 00 00 00 02 01 00 0A 00 00 01 00 00 00 00 0E 0D
4.6. Order
To send control order of 0# slaverunning freq. is 0 9.99HZ
master will send
2A 30 30 34 31 31 30 33 45 37 30 31 44 35 0D
5A 00 00 04 01 01 00 03 0E 07 00 00 00 1E 0D
Slave will respondrunning freq. is 0 9.99HZ
2A 30 30 30 30 31 30 30 30 30 33 45 37 30 32 36 30 0D
5A 00 00 00 00 01 00 00 00 00 00 03 E7 00 00 00 EB 0D
SUNFAR C320 89
Appendix
OPTIONS
1. Operation panel
Sometimes users need to take operation panel out of the inverter or control cabinet, if users purchase panel
base and wire, it is convenient to install and debug. Wire between operation panel and inverter should be
less than 15m. If the length is above 15m, long-distance control line is needed.
1.1 Appearance of panel base
Fig-A Dimension of panel base
Fig-B Hole dimension of panel base
1.2 Appearance of small panel base
Fig-D Hole dimension of small panel base

Fig-C Dimension of small panel base
It is recommended that user take Fig-B and Fig-D Hole dimension of panel base.
90
SUNFAR C320
1.3 Installation of panel base

Open a hole on the control cabinet according to dimension of panel base. And put the panel horizontal into
the hole. Then four locks in panel base will lock. There is an interface on the bottom of base, please insert the
long-distance control wire into it.
2.
Brake resistance
The brake resistance is shown following table.

Model
Applied motorKw
Power of brake resistance

Kw
Brake resistance
Brake torque
C320-2S0015
1.5
0.4
75
100
C320-2S0022
2.2
0.6
50
100
C320-2S0037
3.7
35
100
C320-4T0015
1.5
0.5
300
100
C320-4T0022
2.2
0.65
200
100
C320-4T0037
3.7
1.0
125
100
C320-4T0055
5.5
1.5
85
100
C320-4T0075
7.5
2.0
65
100
C320-4T0110
11
2.5
50
100
C320-4T0150
15
3.6
35
100
C320-4T0185
18.5
4.5
30
100
C320-4T0220
22
5.5
25
100
C320-4T0300
30
6.5
20
100
C320-4T0370
37
8.5
15
100
C320-4T0450
45
12
12
100
C320-4T0550
55
15
10
100
C320-4T0750
75
18
100
C320-4T0900
90
18
100
C320-4T1100
110
25
100
C320-4T1320
132
30
100
C320-4T1600
160
36
100
C320-4T1850
185
42
3.5
100
C320-4T2000
200
45
100
C320-4T2200
250
50
100
C320-4T2500
C320-4T2800
If the braking effect is not obvious, please decrease brake resistance and increase power of brake resistance
according to proportion.
SUNFAR C320 91

264869621

Uploaded by

Copyright:

Available Formats

264869621

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

264869621

Uploaded by

Copyright:

Available Formats

SUNFAR C320 1

C320 series of Inverter

SHENZHEN SUNFAR ELECTRIC TECHNOLOGIES CO.,LTD

C320 Series of Sensorless Vector Inverter Operation Manual

SHENZHEN SUNFAR ELECTRIC TECHNOLOGIES CO., Ltd.

C320 Series of Sensorless Vector Inverter Operation Manual

1.1 Model explanation 6

7 FAULT DIAGNOSIS AND COUNTERMEASURES 72

Appendix RS485 COMMUNICATION PROTOCOL

C320 Series of Sensorless Vector Inverter Operation Manual

Inverters nameplate data

3PH 380V 50/60Hz

Rated output capacity and current

Product series No.

Warning: If user does not operate

This symbol will hint some useful

This symbol will hint some items that

Do not put the inverter on the combustible material.

It must be operated by professional worker when wiring.

C320 Series of Sensorless Vector Inverter Operation Manual

Do not touch the radiator after power-off at least 10 minutes.

Be sure to install the inverter in a well-ventilated ambient.

C320 Series of Sensorless Vector Inverter Operation Manual

1.1 Model explanation

1.2 Appearance description

Control circuit terminals

Cable inlet of control circuit

Main circuit terminals

Cable inlet of mian circuit

It is fit for C320-2S0015C320-2S0037/ C320-4T0015C320-4T0075/C320-2T0015C320-2T0037.

1.Refer to the instruction manual before installation

It is fit forC320-4T0110C320-4T0750 / C320-2T0055C320-2T0450

C320 Series of Sensorless Vector Inverter Operation Manual

1.Refer to the instruction manual before installation and

It is fit for C320-4T0900C320-4T1100 / C320-2T0550

General load (G-load) ([F0.15]=0)

Pump and fan load (P-load) ([F0.15]=1)

C320 Series of Sensorless Vector Inverter Operation Manual

Pump and fan load (P-load) ([F0.15]=1)

Three-phase (4T****) 0 ~380V

Single-phase (2S****) 0~220V

Rated Voltage and freq.

0.1% of maximum freq.

Within 0.2% of maximum output freq.

Within 0.01% of setting freq.

0.1% of maximum freq.

0.1% of maximum output freq.

Reference freq. can be discretionally set between 5 and 600Hz.

Automatically adjust the ration of voltage to frequency according to

While freq equals 1, the torque is 150% rated torque.

the parameter of motor and unique arithmetic.

Under voltage inhibit

Current close-circuit control can avoid the current attack.

C320 Series of Sensorless Vector Inverter Operation Manual

Embedded PID controller can preset freq. Standard positioning RS485

DC voltage05 and 010VDC current 020mA

It can be set by Operation panel, RS485, UP/DW terminal and combination

Up to 8 stages of programmable multi-speed control, 6 kinds of running mode

Automatic energy saving

Determine speed and restart