Hotbeds and Cold Frames: Building The Hotbed or Cold Frame

General Horticulture HO-53-W
Department of Horticulture and Landscape Architecture
Purdue University Cooperative Extension Service West Lafayette, IN
Hotbeds and Cold Frames

Michael N. Dana and B. Rosie Lerner
Hotbeds and cold frames are used for the growing of

plants out of the normal season. They are especially
useful in early spring, but such structures can also
extend the growing season in autumn. With a hotbed or
cold frame, Indiana gardeners can get an early start to
successfully grow vegetables that require longer growing seasons.
Gardeners nd it advantageous to have vigorous, stocky
plants ready to plant out as soon as weather conditions
permit. Earliness is a particularly important factor for
cool season vegetables such as cabbage, cauliower,
lettuce, and spinach.
Hotbed or Cold Frame?

The hotbed and the cold frame are identical in structure
(see Figure 1). The only difference between them is the
source of heat. The sun supplies all the heat in a cold
frame, whereas sunlight is supplemented by another
heat source in a hotbed. Plant growth is slower in a cold
frame than in a hot bed. A cold frame is most suited to
use with the cool season crops mentioned above, while
peppers, tomatoes, eggplants, and other warm season
vegetables ourish in a hotbed.
Building the Hotbed or Cold Frame

Especially if you are constructing only a cold frame,
subdivide it into at least two sections. When the earlier,
cool season crop seedlings are growing they will require
ventilation. At the same time, later warm season crop
seeds will require warmer temperatures for germination. With two sections, you can ventilate one part while
keeping the other sash closed.
Location
The plant bed should be placed where it will be well
protected from the wind, on a well-drained spot and near
a good supply of water. If appropriate, it should be near
a source of electricity. A small structure may be built as
a lean-to against the house. It should have full exposure
to the sun, with a southern orientation preferred. Painting the inside surfaces white or silver will help maximize
the light level for the plants.
Figure 1. Typical cold frame.
Reviewed 7/05
Purdue University Cooperative Extension Service
Page 1 of 4


Construction
Construction of both the hotbed and cold frame begins
with excavation to a depth of a few inches to 3 feet
depending on type. Bed width depends on the size of
sash or top panel to be used, but it is generally 4-6 feet.
Length is also determined by the sash dimensions and
square footage requirements for the bed. Standard commercial beds are built in multiples of 3 feet.
The framework of the bed can be constructed from wood,
concrete, or concrete block. When wood is used, the
boards may be 1, or preferably 2, inches thick. Redwood, cedar, or lumber pressure-treated with a preservative is best. The front of the bed, to the south, should
be 10 to 12 inches high inside, with 2 inches extending
below ground level. The back portion should be 6-12
inches higher than the front, having a minimum slope of
1 inch per foot. Beds made from concrete should extend
into the soil 6 to 8 inches, and the wall should be at least
3 inches in thickness. The bed should be true for a snug
t. The soil on the outside should be banked around the
frame to conserve heat. Be sure the soil slopes away
from the walls to assure good drainage.
proving the aeration of the bed. Fill the bed with manure;
then tamp rmly and evenly, especially in the corners.
The tamped manure should extend an inch or so above
the ground level on the inside of the frame. Moisten the
manure evenly with lukewarm water to insure uniform
heating.
Cover the manure with 3 or 4 inches of good, weed-free
garden soil. Soil that is fairly warm when put in the bed
permits earlier heating and consequently early seeding.
When the bed is ready, t the sash over the bed, and
insert 2 or 3 accurate thermometers 2 to 3 inches into the
soil in representative places to check on the heat. When
the soil temperature drops to 75F or slightly less, the
bed is ready for seeding.
Electric Hotbed (Figure 3). Electric heating requires an
insulated heating cable enclosed in a exible lead sheath
covering. About 2 feet of cable for each square foot of
bed area is needed. Excavate the soil 2 or 3 inches
below the frame level. Then put down 4 inches of cinders
or sand as a base for the cable.
Cold frame or hotbed sash may be constructed of glass,

Plexiglas, Fiberglass, polyethylene, or other translucent/
transparent material. More permanent structures should
have glass sash. Frequently, old window frames can be
salvaged and reused for this purpose. Standard commercially available sash is 3 feet by 6 feet, and melon
sash is 4 feet by 10 feet. Additional sash frames covered with lath or fabric may be desirable for extending
the use of your plant bed; they will provide shading once
temperatures get high enough. Sash may be attached
on the high side with hinges or left unattached for easy,
complete removal.
Hotbed Heating Systems

Pit Hotbed (Figure 2). When manure is used to supply
heat, the soil inside the bed should be excavated to a
depth of 16 to 18 inches. A 4-inch layer of coarse cinders
or gravel forms the bottom portion for drainage and im-
Figure 3. Electric hotbed with thermostatic control.
When you lay the cable, start and end with the outside
row 3 inches away from the frame, and make a series of
long loops 6 inches apart across the bed. Laying hardware cloth over the cable prior to covering it with soil will
help prevent the cable from being pulled out of the soil.
A 3- to 4-inch layer of good planting soil, or sand when
used for sweet potatoes and melons, should then be put
over the cable. The cable, when attached to a thermostat
and a 110-volt outlet, automatically controls the temperature in the bed.
Figure 2. Cross section of a manure-heated pit hotbed.
Page 2 of 4
Flue-heated Hotbed. Furnace ring, the use of dry

heat, is a very satisfactory and economical way to heat
a hotbed; several fuels, such as oil or coal, can be used.
Reviewed 7/05


The heat passes through heat-conducting pipes, generally 4-inch tile, from the furnace to a 6- to 8-inch ue or
chimney on the outside of the bed at the opposite end
from the heat source.
When constructing the ue-heated bed, it is best to start
with the re box. A pit 3 feet square and 6 feet deep on
the inside can serve as the furnace room. A steel drum
makes a good stove when laid on the side with a door at
the bottom of one end and two outlets at the top of the
opposite end. The outlet end of the drum should be 3 to
4 feet away from the front end of the bed.
Connect two lines of heat-conducting pipes to the furnace, and lay them about 18 inches from each side of the
bed, slanted upwards to about 6 inches from the surface
at the far end.
The frame of the bed, preferably concrete, should be built
around the tile, and the pipes should be covered with
cinders or clean sand. A bed 6 feet wide and 40 to 50
feet in length is a good size. Use sand for the growing of
sweet potato plants or for a base for ats or melon boxes,
and use 3 inches of soil for direct seeding.
The re should be started as soon as the sashes are in
place, at least 3 to 4 days ahead of seeding or bedding
time. Except during cold weather, one night and one day
of ring will generally supply enough heat to keep the bed
warm.
Steam- or Hot Water-heated Hotbed. The use of steam
or hot water circulating systems is practical when the
beds are supplementary to a greenhouse operation. The
heating pipes may be placed under the soil or around the
inside edge near the top of the frame. The heat is turned
on or off as needed.
Hotbed or Cold Frame Operation

Soil and Planting
The soil or other growing medium that you use in the
hotbed or cold frame should be the best you can nd,
because many weed seeds, insects, and diseases are
found in ordinary soil. Table 1 provides a suggested mix
for growing medium. The use of fertilizers in the seed
bed should be avoided to prevent excessive seedling
growth.
Reviewed 7/05
Table 1. Suggested soil mixture.

_____________________________________________
Ingredients
1 gallon
1 bushel
_____________________________________________
Shredded sphagnum
peat moss
Vermiculite #3, or 4
Limestone, dolomitic
preferred
20% superphosphate
(powdered)
5-10-5
Iron (chelated such as
NaFe, 138 or 330)
Wetting agent1
2 qts.
2 qts.
1/2 bu.
1/2 bu.
1 Tbsp.
5 Tbsp.
1/2 Tbsp.
2-1/2 Tbsp.
7-1/2 Tbsp.
1/2 tsp.
1/2 tsp. in
1/2 gal. water
_____________________________________________
1
Wetting agents or surfactants increase the ease of wetting peat moss and mixes high in organic matter. A small
quantity added to water will help to uniformly distribute
applied water. Dish detergent may be used as a wetting
agent at double the recommended rate. Note: Bushels
are level full, not packed. Tablespoons and teaspoons
are level amounts.
The heat in the bed will determine, in part, when the seed
should be sown. Generally, 30 to 40 days will be required from seeding time to transplanting time. The seed
may be sown directly in the soil or in containers such
as peat pots, clay or plastic ower pots, milk or cottage
cheese cartons, or in ats. As a rule, when young plants
receive a double transplanting, 50 to 100 seeds are sown
per foot of row in rows 6 to 8 inches apart.
When you use containers, place two seeds in each
compartment of the container. Later thin to one plant.
After planting the seed, spread a light covering of sand
or vermiculite over the surface. When you bed sweet
potatoes, space the roots an inch or so apart and cover
with 2 to 3 inches of good clean sand.
Temperature Control
The temperature of the bed should be from 70 to 75 F
until the young plants are about 1 inch high. Then lower
the temperature to 65F during the day and 55 to 60 F
for the night, except for sweet potato plants. Growing the
plants cool produces better plants and as a rule results
in earlier setting of the fruit, particularly for tomatoes, melons, and peppers.
Page 3 of 4


A straw mat, roong paper, or tarpaulin should be readily available to cover the cold frame when cold weather
threatens to cause freezing temperatures. A 100-watt
lamp left burning during the cool nights will aid in keeping
the bed warm.
Water and Ventilation Regulation

Plants grow best with a limited amount of water and with
controlled temperatures. Apply water, preferably warm,
during the morning when the sun is shining. Over-watering and high temperatures encourage trouble from
diseases and can cause spindly growth.
Proper ventilation of hotbeds and cold frames not only
controls temperature, but also helps prevent dampingoff disease. When ventilating the bed, raise the sash
opposite, the direction of the wind. For small structures,
automatic thermostatically controlled sash raising devices
are available. As the season advances, leave the sash
off during the greater part of the day and eventually leave
it off entirelyrst all day, then all day and all night. This
will harden off the plants in preparation for transplanting
to the garden.
Fall and Winter Use

The cold frame or hotbed without heat can be used to
extend the gardening season well past the normal limit of
rst frost. Salad greens for instance, can be productive
until about Thanksgiving.
Start seeds early in the fall. Use the sash only when
night temperatures drop too low. Extra night time insulation can be provided by a tarpaulin or blanket. When
seedlings are ready to transplant, space them about 3-4
inches apart each way. With the onset of cold weather,
use the sash during the day, but continue to give close
attention to necessary ventilation. Harvest as you would
from your early season garden.
Storing vegetables is a convenient winter use of a cold
frame or hotbed without supplemental heat. Remove
12-18 inches of soil from the frame. Place turnips, beets,
carrots, rutabagas, and the like in the hole on a layer of
straw. Then, cover the vegetables with an abundance
of straw followed by the sash and tarpaulin. Such an arrangement should keep the produce unfrozen all winter.
For more information on the subject discussed in this

publication, consult your local ofce of the Purdue University
Cooperative Extension Service.
Cooperative Extension work in Agriculture and Home Economics, state of Indiana, Purdue University, and U.S. Department of Agriculture cooperating; D. Petritz, Director, West Lafayette, IN.
Issued in furtherance of the acts of May 8 and June 30, 1914. The Cooperative Extension Service of Purdue University is an afrmative action/equal opportunity institution.
Page 4 of 4
Reviewed 7/05

Hotbeds and Cold Frames: Building The Hotbed or Cold Frame

Uploaded by

Copyright:

Available Formats

Hotbeds and Cold Frames: Building The Hotbed or Cold Frame

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hotbeds and Cold Frames: Building The Hotbed or Cold Frame

Uploaded by

Copyright:

Available Formats

General Horticulture HO-53-W

Department of Horticulture and Landscape Architecture

Purdue University Cooperative Extension Service West Lafayette, IN