(Sabre) : Non-Extensible UNIT

ELECTRICAL INDUSTRIAL COMPANY (EICo)
LUCY SWITCHGEAR
Non-Extensible UNIT - VRN2a
(Sabre)
Electrical Industrial Company (EICo)

LUCY SWITCHGEAR
Non-Extensible Unit VRN2a Front Panel:
LUCY SWITCHGEAR
(Sabre)
NON-EXTENSIBLE UNIT VRN2a:

General
The Sabre VRN2a is a non extensible RMU comprising of a tee-off vacuum circuit
breaker and two fault-make load break ring switches contained within a common
SF6 gas insulated stainless steel enclosure. The unit is suitable for both indoor and
outdoor applications and can be used either as a freestanding unit, or for mounting
to a transformer .
1- Stainless Steel Gas Enclosure

The gas enclosure is manufactured from stainless steel and fabricated utilizing
automatic 'robot welding' techniques to produce consistent leak- free equipment.
2- Housing
The housing of the Sabre VRN2a is fully treated; using zinc coated steel and electro
statically applied oven cured paint, to resist weather and pollution attacks. All units
are provided with a hinged, weatherproof and lockable door. The external support
legs can provide a Tee-Off bushing height of 1402, 1320mm or 1100mm.
3-Tee-Off Circuit Breaker

The tee-off circuit breaker comprises of three vacuum interrupters, which have a
fault-make, fault-break rating. Opening of the circuit breaker is achieved by manually
operating the handle as standard .Earthing of the outgoing cable, from the tee-off
circuit breaker, is achieved by the use of the circuit breaker in series with the off-load
disconnect or / selector switch.
.
4-Ring Switches
The two ring switches are of the single break, fault-make / load- break 3 position
types, 'ON', 'OFF' and 'EARTH'.
5- Operation
All operating positions and instructions are indicated on the main panel at the front of
the unit. Operation is by means of manually independent mechanisms, which are
mounted externally to the gas enclosure The tee-off vacuum circuit breaker has two
operating positions, 'ON' or 'OFF', with an off-load, interlocked selector allowing
isolation & earthing of the tee-off circuit A single, "Y"-bar type operating handle is
stored at the front door. Symbols located on the end of the operating handle indicate
direction of operation.
.
.
6-Test Facilities
The Sabre VRN2a has fully interlocked integrated ring switch cable test facilities in
accordance with ENATS 41-36 requirements. Access to the test terminals is
achieved by pulling a lever located on the front fascia inside the front door. This will
allow the cover underneath the unit to drop down. Where cable test facilities are
required on the T-off, an alternative interlocked system, using plug-in
connectors, is available.
7- Interlocks
Positive safety interlocks are incorporated on all switch positions.
8- Padlocks
The door has a quarter-turn lock that can be padlocked. The handle has a padlock
hasp hole size 8mm diameter.
All switch and selector positions can be padlocked. The padlock hasp hole size is
8.5mm diameter.
9- Transformer Protection
The circuit breaker enables the VRN to protect transformers with ratings well in
excess of those of a comparable HV fused unit. Protection is achieved by the use of
ring core current transformers in combination with Time Limit Fuse links or a
protection relay. The ring core current transformers are mounted around the rear teeoff bushings, external to the SF6 chamber, but within the cladding of the unit. The
Time Limit Fuses, or the protection relay, are mounted behind a cover at the front of
the unit.
10- Time Limit Fuse Protection (TLF)
Dual ratio CT's are provided as standard transformer protection. Access for CT ratio
change is provided by means of a cover plate on the front panel of the unit.
11- Cable Termination

The bushings for each ring switch are located either side of the unit. Both sets of
bushings are type C with in-line bolted connections
M16 threaded in accordance with EN50181. The tee-off bushings are located at the
rear of the unit and are in-line bolted connections
M12 threaded. All tee-off bushings are fitted with white stress relief collars and
MUST NOT be removed unless a taper kit is being fitted (see next page ).
If cabling boxes are fitted, then the bushings are accessible by removing the cabling
box side cover.
The maximum cable size that can be used is:
300mm
3 - core
500mm
single - core.
Torque Settings On Cable Bushings
M16 into copper - 75Nm
M12 copper thread or into copper - 35Nm
The following types of terminations can be used with the Sabre VRN2a
RING SWITCH BUSHINGS
Insulating Bushing Boot
PROFILE C
Bolted Separable
Tee-off taper kit
Tee- off Bushing Insulating Bushing Boot
12- Marshalling Box

The marshalling box located on the left hand side of the unit and houses the
terminals for all customer options including ring switch actuators, pressure switch
and EFI CTs
13- VRN2a Unit Floor Mounting Dimensions

The units are designed for bolting down onto a concrete plinth using 4 - M16 bolts
TLF TRIP PROTECTION SYSTEM DIAGRAM:
14- Earthing
The Sabre VRN2a unit should be earthed at either of the primary earth points.
These earth points are located at the rear of the unit, either side of the Cable
Test Access Cover as shown.

Lucy switchgear
Non Extensible Unit VRN2a schematic line diagram:
Technical data
Non Extensible Unit VRN2a
1- Rated Voltage
2- Impulse Withstand Voltage
12KV (15.5KV)
75KV (95KV )
3- Normal Current
- Ring Switches
630Amp
- Tee- Off Circuit Breaker
250Amp
4- Short Circuit Peak Making current

- Ring Switches
50KA
- Tee-Off Circuit Breaker
50KA
5- Short Circuit Breaking Current

20KA RMS
6- 3 Second Short Time Current

- Ring Switches
20KA
- Tee- Off Circuit Breaker
20KA
7- Earth Switch Peak Making Current

- Ring Switches
20KA
7.9 KA
8-
9-
Internal Arc Rating

-
Freestanding
20KA 1 sec
Transformer Mounted
20KA 1 sec
Gas pressure
- Min Operating Pressure
O Bar G
10-
IP Rating
11-
Weight
up to IP54W
350kg

LUCY SWITCHGEAR
Non Extensible Unit VRN2a Dimensions:

(Sabre) : Non-Extensible UNIT

Uploaded by

Copyright:

Available Formats

(Sabre) : Non-Extensible UNIT

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

(Sabre) : Non-Extensible UNIT

Uploaded by

Copyright:

Available Formats

ELECTRICAL INDUSTRIAL COMPANY (EICo)

Non-Extensible UNIT - VRN2a

Electrical Industrial Company (EICo)

ELECTRICAL INDUSTRIAL COMPANY (EICo)

NON-EXTENSIBLE UNIT VRN2a:

1- Stainless Steel Gas Enclosure

3-Tee-Off Circuit Breaker

11- Cable Termination

M12 copper thread or into copper - 35Nm

RING SWITCH BUSHINGS

Insulating Bushing Boot

Tee-off taper kit

Tee- off Bushing Insulating Bushing Boot

12- Marshalling Box

13- VRN2a Unit Floor Mounting Dimensions

TLF TRIP PROTECTION SYSTEM DIAGRAM:

ELECTRICAL INDUSTRIAL COMPANY (EICo)

Non Extensible Unit VRN2a schematic line diagram:

- Tee- Off Circuit Breaker

4- Short Circuit Peak Making current

- Tee-Off Circuit Breaker

5- Short Circuit Breaking Current

6- 3 Second Short Time Current

- Tee- Off Circuit Breaker

7- Earth Switch Peak Making Current

- Tee-Off Circuit Breaker

Internal Arc Rating

ELECTRICAL INDUSTRIAL COMPANY (EICo)

You might also like