XV1900 RoadlinerStratoliner06 09 REPAIR MANUAL

Fix it like a Pro
How to use this Service Manual

In the bookmarks to the left you will find different
segments of this manual:
Service Manual
This is the standard manual for this vehicle. Use this
segment as your major point of reference and information.
Supplementary Service Manual (if available)

These segments are updates and additions to the standard
service manual. They are added as needed when certain
changes are made to the model. Be sure to check these
for additional information that may be lacking from the
regular service manual.
EAS20090
HOW TO USE THIS MANUAL

This manual is intended as a handy, easy-to-read reference book for the mechanic. Comprehensive
explanations of all installation, removal, disassembly, assembly, repair and check procedures are laid
out with the individual steps in sequential order.
The manual is divided into chapters and each chapter is divided into sections. The current section title
is shown at the top of each page 1.
Sub-section titles 2 appear in smaller print than the section title.
To help identify parts and clarify procedure steps, there are exploded diagrams 3 at the start of each
removal and disassembly section.
Numbers 4 are given in the order of the jobs in the exploded diagram. A number indicates a disassembly step.
Symbols 5 indicate parts to be lubricated or replaced.
Refer to SYMBOLS.
A job instruction chart 6 accompanies the exploded diagram, providing the order of jobs, names of
parts, notes in jobs, etc.
Jobs 7 requiring more information (such as special tools and technical data) are described sequentially.
EAS20100
SYMBOLS
The following symbols are used in this manual
for easier understanding.
NOTE:
The following symbols are not relevant to every

vehicle.
1. Serviceable with engine mounted

2. Filling fluid
3. Lubricant
4. Special tool
5. Tightening torque
6. Wear limit, clearance
7. Engine speed
8. Electrical data
9. Engine oil
10. Gear oil
11. Molybdenum-disulfide oil
12. Wheel-bearing grease
13. Lithium-soap-based grease
14. Molybdenum-disulfide grease
15. Apply locking agent (LOCTITE)
16. Replace the part
T.
R.
10
E
12
11
13
B
15
14
M
LS
16
LT
New
EAS20110
TABLE OF CONTENTS
GENERAL INFORMATION
SPECIFICATIONS
PERIODIC CHECKS AND ADJUSTMENTS
CHASSIS
ENGINE
FUEL SYSTEM
ELECTRICAL SYSTEM
TROUBLESHOOTING
GENERAL INFORMATION
IDENTIFICATION ............................................................................................ 1-1
VEHICLE IDENTIFICATION NUMBER..................................................... 1-1
MODEL LABEL ......................................................................................... 1-1
FEATURES ..................................................................................................... 1-2
OUTLINE OF THE FI SYSTEM................................................................. 1-2
FI SYSTEM ............................................................................................... 1-3
INSTRUMENT FUNCTIONS..................................................................... 1-4
IMPORTANT INFORMATION ......................................................................... 1-8
PREPARATION FOR REMOVAL AND DISASSEMBLY .......................... 1-8
REPLACEMENT PARTS .......................................................................... 1-8
GASKETS, OIL SEALS AND O-RINGS .................................................... 1-8
LOCK WASHERS/PLATES AND COTTER PINS..................................... 1-8
BEARINGS AND OIL SEALS.................................................................... 1-9
CIRCLIPS.................................................................................................. 1-9
CHECKING THE CONNECTIONS................................................................ 1-10
SPECIAL TOOLS.......................................................................................... 1-11
IDENTIFICATION
EAS20130
IDENTIFICATION
EAS20140
VEHICLE IDENTIFICATION NUMBER

The vehicle identification number 1 is stamped
into the right side of the steering head pipe.
EAS20150
MODEL LABEL
The model label 1 is affixed to the frame under
the rider seat. This information will be needed to
order spare parts.
1-1
FEATURES
EAS20170
FEATURES
ET1D71017
OUTLINE OF THE FI SYSTEM

The main function of a fuel supply system is to provide fuel to the combustion chamber at the optimum
air-fuel ratio in accordance with the engine operating conditions and the atmospheric temperature. In
the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion
chamber is created by the volume of the intake air and the fuel that is metered by the jet used in the
respective carburetor.
Despite the same volume of intake air, the fuel volume requirement varies by the engine operating conditions, such as acceleration, deceleration, or operating under a heavy load. Carburetors that meter the
fuel through the use of jets have been provided with various auxiliary devices, so that an optimum airfuel ratio can be achieved to accommodate the constant changes in the operating conditions of the engine.
As the requirements for the engine to deliver more performance and cleaner exhaust gases increase,
it becomes necessary to control the air-fuel ratio in a more precise and finely tuned manner. To accommodate this need, this model has adopted an electronically controlled fuel injection (FI) system, in place
of the conventional carburetor system. This system can achieve an optimum air-fuel ratio required by
the engine at all times by using a microprocessor that regulates the fuel injection volume according to
the engine operating conditions detected by various sensors.
The adoption of the FI system has resulted in a highly precise fuel supply, improved engine response,
better fuel economy, and reduced exhaust emissions.
21 20 16
4 5 6 7 8
19 18
9 10
17 16 15
11
12
14 13
15. Lean angle sensor

16. Spark plug
17. Injector #1
18. Crankshaft position sensor
19. Injector #2
20. Cylinder-#2 right ignition coil
21. Cylinder-#2 left ignition coil
1. Air temperature sensor

2. ISC (idle speed control) unit
3. Cylinder-#2 intake air pressure sensor
4. Engine temperature sensor
6. Throttle position sensor
9. Fuel pump
10. ECU (electronic control unit)
11. Relay unit (fuel pump relay)
12. EXUP servo motor
13. Speed sensor
14. O2 sensor
1-2
FEATURES
ET1D71018
FI SYSTEM
The fuel pump delivers fuel to the fuel injector via the fuel filter. The pressure regulator maintains the
fuel pressure that is applied to the fuel injector at only 392 kPa (3.92 kg/cm, 55.7 psi). Accordingly,
when the energizing signal from the ECU energizes the fuel injector, the fuel passage opens, causing
the fuel to be injected into the intake manifold only during the time the passage remains open. Therefore, the longer the length of time the fuel injector is energized (injection duration), the greater the volume of fuel that is supplied. Conversely, the shorter the length of time the fuel injector is energized
(injection duration), the lesser the volume of fuel that is supplied.
The injection duration and the injection timing are controlled by the ECU. Signals that are input from the
throttle position sensor, crankshaft position sensor, intake air pressure sensor, air temperature sensor,
engine temperature sensor, speed sensor and O2 sensor enable the ECU to determine the injection
duration. The injection timing is determined through the signals from the crankshaft position sensor. As
a result, the volume of fuel that is required by the engine can be supplied at all times in accordance with
the driving conditions.
Illustration is for reference only.
6
7
1
A
#2 #1
9
10
15
B
14
13
11
12
13. Intake air pressure sensor

14. Throttle body
15. Air filter case
1. Pressure regulator
2. Fuel pump
3. Fuel injector
4. Ignition coil
9. O2 sensor
10. Catalytic converter
A. Fuel system
B. Air system
C. Control system
1-3
FEATURES
ET1D71036
INSTRUMENT FUNCTIONS
Multi-function meter unit
EW1D71008
WARNING
Be sure to stop the vehicle before making

any setting changes to the multi-function
meter unit.
1. SELECT switch
2. RESET switch
Speedometer
1
3
1. Speedometer
2. Fuel gauge
3. Odometer/tripmeter/fuel reserve
tripmeter/clock
4. Tachometer
The multi-function meter unit is equipped with

the following:
a speedometer (which shows the riding speed)
a tachometer (which shows the engine speed)
a fuel gauge
an odometer (which shows the total distance
traveled)
two tripmeters (which show the distance traveled since they were last set to zero)
a fuel reserve tripmeter (which shows the distance traveled on the fuel reserve)
a clock
a self-diagnosis device
a brightness control mode
1. Speedometer
The speedometer shows the riding speed.

When the key is turned to ON, the speedometer needle will sweep once across the speed
range and then return to zero in order to test the
electrical circuit.
Tachometer
NOTE:
Be sure to turn the key to ON before using the

SELECT and RESET switches.
To switch the odometer, the tripmeters and the
fuel reserve tripmeter displays between kilometers and miles, press the SELECT switch
for at least two seconds. (For USA and California only)
2
1. Tachometer
2. Tachometer red zone
The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal
power range.
When the key is turned to ON, the tachometer
needle will sweep once across the r/min range
and then return to zero r/min in order to test the
electrical circuit.
1-4
FEATURES
Push the SELECT switch to switch the display
between the odometer mode ODO, the tripmeter modes TRIP 1 and TRIP 2 and the clock
mode in the following order:
ODO TRIP 1 TRIP 2 Clock ODO
If the fuel level warning light comes on, the
odometer display will automatically change to
the fuel reserve tripmeter mode F-TRIP and
start counting the distance traveled from that
point. In that case, push the SELECT switch to
switch the display between the various tripmeter, odometer, and clock modes in the following
order:
F-TRIP TRIP 1 TRIP 2 Clock ODO
F-TRIP
To reset a tripmeter, select it by pushing the SELECT switch, and then push the RESET
switch for at least one second. If you do not reset
the fuel reserve tripmeter manually, it will reset
itself automatically, and the display will return to
the prior mode after refueling and traveling 5 km
(3 mi).
EC1D71017
CAUTION:
Do not operate the engine in the tachometer

red zone.
Red zone: 5000 r/min and above
Fuel gauge
1. Fuel gauge
The fuel gauge indicates the amount of fuel in

the fuel tank. The needle moves towards E
(Empty) as the fuel level decreases. When the
needle reaches E, approximately 3.0 L (0.79
US gal) (0.66 Imp.gal) remain in the fuel tank. If
this occurs, refuel as soon as possible.
When the key is turned to ON, the fuel gauge
needle will sweep once across the fuel level
range and then return to the current amount in
order to test the electrical circuit.
Clock mode
NOTE:
Do not allow the fuel tank to empty itself completely.

The fuel gauge does not indicate the correct
fuel level for the first 5 km/h (3 mi/h) after refueling.
1. Clock
To set the clock:

1. Push the SELECT switch to change the display to the clock mode.
2. Push the SELECT and RESET switches
together for at least two seconds.
3. When the hour digits start flashing, push the
RESET switch to set the hours.
4. Push the SELECT switch, and the minute
digits will start flashing.
5. Push the RESET switch to set the minutes.
6. Push the SELECT switch and then release
it to start the clock.
Odometer, tripmeter, and clock modes
1
1. Odometer/tripmeter/fuel reserve
tripmeter/clock
Self-diagnosis device
This model is equipped with a self-diagnosis device for various electrical circuits.
1-5
FEATURES
If any of those circuits are defective, the engine
trouble warning light will come on, and then the
odometer/tripmeter/clock display will indicate a
two-digit error code (e.g., 12, 13, 14).
If the odometer/tripmeter/clock display indicates
any error codes, note the code number, and
then check the vehicle. Refer to FUEL INJECTION SYSTEM on page 7-27.
EC1D71018
CAUTION:
If the display indicates an error code, the vehicle should be checked as soon as possible
in order to avoid engine damage.
1. Multi-function meter unit panel

2. Item number
3. Brightness level
4. Adjust the multi-function meter unit panel

brightness level by pushing the RESET
switch.
5. Push the SELECT switch to select the LCD.
Item number 2 is displayed.
Adjust the LCD brightness level by pushing
the RESET switch.
Brightness control mode
1
3
4
5
2
1.
2.
3.
4.
5.
Multi-function meter unit panel

LCD
Speedometer needle
Tachometer needle
Fuel gauge needle
2
3
The brightness can be adjusted for the following:

the multi-function meter unit panel (item number 1)
the LCD (item number 2)
the speedometer, tachometer, and the fuel
gauge needles (item number 3)
Select the brightness control mode as follows.
1. Turn the key to OFF.
2. Push and hold the SELECT switch.
3. Turn the key to ON, and then release the
SELECT switch after five seconds.
1. LCD
2. Item number
3. Brightness level
6. Push the SELECT switch to select the

speedometer, tachometer, and the fuel
gauge needles.
Adjust the brightness level of the speedometer, tachometer, and the fuel gauge needles
by pushing the RESET switch.
1
2
3
4
5
1. Speedometer needle
2. Tachometer needle
1-6
FEATURES
3. Fuel gauge needle
4. Item number
5. Brightness level
7. Push the SELECT switch.

The odometer/tripmeter/clock display will return to the prior mode.
1-7
IMPORTANT INFORMATION
EAS20180
EAS20190
PREPARATION FOR REMOVAL AND

DISASSEMBLY
1. Before removal and disassembly, remove all
dirt, mud, dust and foreign material.
EAS20210
GASKETS, OIL SEALS AND O-RINGS

1. When overhauling the engine, replace all
gaskets, seals and O-rings. All gasket surfaces, oil seal lips and O-rings must be cleaned.
2. During reassembly, properly oil all mating
parts and bearings and lubricate the oil seal
lips with grease.
2. Use only the proper tools and cleaning equipment.

Refer to SPECIAL TOOLS on page 1-11.
3. When disassembling, always keep mated
parts together. This includes gears, cylinders,
pistons and other parts that have been mated through normal wear. Mated parts must
always be reused or replaced as an assembly.
1.
2.
3.
4.
Oil
Lip
Spring
Grease
EAS20220
LOCK WASHERS/PLATES AND COTTER

PINS
After removal, replace all lock washers/plates
1 and cotter pins. After the bolt or nut has been
tightened to specification, bend the lock tabs
along a flat of the bolt or nut.
4. During disassembly, clean all of the parts and

place them in trays in the order of disassembly. This will speed up assembly and allow for
the correct installation of all parts.
5. Keep all parts away from any source of fire.
EAS20200
REPLACEMENT PARTS
Use only genuine Yamaha parts for all replacements. Use oil and grease recommended by
Yamaha for all lubrication jobs. Other brands
may be similar in function and appearance, but
inferior in quality.
1-8
EAS20230
BEARINGS AND OIL SEALS

Install bearings and oil seals so that the manufacturers marks or numbers are visible. When
installing oil seals 1, lubricate the oil seal lips
with a light coat of lithium-soap-based grease.
Oil bearings liberally when installing, if appropriate.
ECA13300
CAUTION:
Do not spin the bearing with compressed air

because this will damage the bearing surfaces.
EAS20240
CIRCLIPS
Before reassembly, check all circlips carefully
and replace damaged or distorted circlips. Always replace piston pin clips after one use.
When installing a circlip 1, make sure the
sharp-edged corner 2 is positioned opposite
the thrust 3 that the circlip receives.
1-9
CHECKING THE CONNECTIONS

EAS20250
CHECKING THE CONNECTIONS

Check the leads, couplers, and connectors for
stains, rust, moisture, etc.
1. Disconnect:
Lead
Coupler
Connector
2. Check:
Lead
Coupler
Connector
Moisture Dry with an air blower.
Rust/stains Connect and disconnect several times.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
NOTE:
If there is no continuity, clean the terminals.

When checking the wire harness, perform
steps (1) to (3).
As a quick remedy, use a contact revitalizer
available at most part stores.
3. Check:
All connections
Loose connection Connect properly.
NOTE:
If the pin 1 on the terminal is flattened, bend it

up.
4. Connect:
Lead
Coupler
Connector
NOTE:
Make sure all connections are tight.

5. Check:
Continuity
(with the pocket tester)
1-10
SPECIAL TOOLS
EAS20260
SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly. Use only
the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools
or improvised techniques. Special tools, part numbers or both may differ depending on the country.
When placing an order, refer to the list provided below to avoid any mistakes.
NOTE:
For U.S.A. and Canada, use part number starting with YM-, YU-, or ACC-.
For others, use part number starting with 90890-.
Tool name/Tool No.
Illustration
Reference
pages
Pocket tester
90890-03112
YU-03112-C
1-10, 5-79,
7-73, 7-74,
7-75, 7-79,
7-80, 7-81,
7-82, 7-83,
7-84, 7-85,
7-86, 7-87,
7-88, 7-89,
7-90, 7-91
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-9
3-6, 5-61
Tappet adjusting tool (4 mm)

90890-04133
Valve adjustment wrench 3 mm & 4 mm
YM-08035-A
3-6, 3-7
Vacuum gauge
90890-03094
Carburetor synchronizer
YU-44456
3-7
YU-44456
1-11
SPECIAL TOOLS
Tool name/Tool No.
Illustration
Reference
pages
Timing light
90890-03141
Inductive clamp timing light
YU-03141
3-10
Oil filter wrench

90890-01426
YU-38411
3-12
Belt tension gauge

90890-03170
Rear drive belt tension gauge
YM-03170
3-24
Steering nut wrench

90890-01403
Spanner wrench
YU-33975
3-26, 4-71
Damper rod holder

90890-01460
4-64, 4-66
T-handle
90890-01326
T-handle 3/8" drive 60 cm long
YM-01326
4-64, 4-66
Fork seal driver

90890-01442
Adjustable fork seal driver (3646 mm)
YM-01442
4-66, 4-67
Pivot shaft wrench

90890-01485
Frame mount insert wrench
YM-01485
5-12
Valve spring compressor

90890-04019
YM-04019
5-39, 5-44
1-12
SPECIAL TOOLS
Tool name/Tool No.
Illustration
Reference
pages
Valve guide remover (6)

90890-04064
Valve guide remover (6.0 mm)
YM-04064-A
5-40
Valve guide installer (6)

90890-04065
Valve guide installer (6.0 mm)
YM-04065-A
5-40
Valve guide reamer (6)

90890-04066
Valve guide reamer (6.0 mm)
YM-04066
5-40
Piston pin puller set

90890-01304
Piston pin puller
YU-01304
5-46
YU-01304
Universal clutch holder

90890-04086
YM-91042
5-60, 5-65
Sheave holder
90890-01701
Primary clutch holder
YS-01880-A
5-60, 5-64,
5-74, 5-75
Yamaha bond No. 1215

90890-85505
(Three Bond No.1215)
5-66, 5-76,
5-93
1-13
SPECIAL TOOLS
Tool name/Tool No.
Illustration
Reference
pages
Rotor puller
90890-01080
Stator rotor puller
YM-01080-A
5-74
Vacuum/pressure pump gauge set

90890-06756
6-12
Pressure gauge
90890-03153
6-12
Fuel pressure adapter

90890-03176
YM-03176
6-12
Digital circuit tester

90890-03174
Model 88 Multimeter with tachometer
YU-A1927
6-12
Ignition checker
90890-06754
Opama pet-4000 spark checker
YM-34487
7-83
1-14
SPECIFICATIONS
GENERAL SPECIFICATIONS ........................................................................ 2-1
ENGINE SPECIFICATIONS............................................................................ 2-2
CHASSIS SPECIFICATIONS........................................................................ 2-10
ELECTRICAL SPECIFICATIONS................................................................. 2-13
TIGHTENING TORQUES.............................................................................. 2-16
GENERAL TIGHTENING TORQUE SPECIFICATIONS......................... 2-16
ENGINE TIGHTENING TORQUES......................................................... 2-17
CHASSIS TIGHTENING TORQUES....................................................... 2-22
LUBRICATION POINTS AND LUBRICANT TYPES .................................... 2-27
ENGINE .................................................................................................. 2-27
CHASSIS ................................................................................................ 2-29
LUBRICATION SYSTEM CHART AND DIAGRAMS ................................... 2-31
ENGINE OIL LUBRICATION CHART ..................................................... 2-31
LUBRICATION DIAGRAMS .................................................................... 2-33
CABLE ROUTING......................................................................................... 2-45
GENERAL SPECIFICATIONS
EAS20280
GENERAL SPECIFICATIONS
Model
Model
XV19SV 1D71 (USA)

XV19SV 1D73 (CDN)
XV19SVC 1D72 (California)
XV19V 4D41 (USA)
XV19V 4D43 (CDN)
XV19VC 4D42 (California)
XV19MV 4D51 (USA)
XV19MV 4D53 (CDN)
XV19MVC 4D52 (California)
XV19CTSV 2C51 (USA)
XV19CTSV 2C53 (CDN)
XV19CTSVC 2C52 (California)
XV19CTV 4P01 (USA)
XV19CTV 4P03 (CDN)
XV19CTVC 4P02 (California)
XV19CTMV 4P11 (USA)
XV19CTMV 4P13 (CDN)
XV19CTMVC 4P12 (California)
Dimensions
Overall length
Overall width
Overall height
2580 mm (101.6 in)

1100 mm (43.3 in)
XV19SV(C)/XV19V(C)/XV19MV(C):
1100 mm (43.3 in)
XV19CTSV(C)/XV19CTV(C)/XV19CTMV(C):
1515 mm (59.6 in)
735 mm (28.9 in)
1715 mm (67.5 in)
155 mm (6.10 in)
3480 mm (137.0 in)
Seat height
Wheelbase
Ground clearance
Minimum turning radius
Weight
With oil and fuel
340.0 kg (750 lb)
364.0 kg (802 lb)
210 kg (463 lb)
186 kg (410 lb)
Maximum load
2-1
ENGINE SPECIFICATIONS
EAS20290
Engine
Engine type
Displacement
Cylinder arrangement
Bore stroke
Compression ratio
Starting system
Air cooled 4-stroke, OHV

1854.0 cm (113.13 cu.in)
V-type 2-cylinder
100.0 118.0 mm (3.94 4.65 in)
9.48 :1
Electric starter
Fuel
Recommended fuel
Fuel tank capacity
Fuel reserve amount
Premium unleaded gasoline only

17.0 L (4.49 US gal) (3.74 Imp.gal)
3.0 L (0.79 US gal) (0.66 Imp.gal)
Engine oil
Lubrication system
Type
Recommended engine oil grade
Engine oil quantity
Total amount
Engine
Oil tank
Without oil filter cartridge replacement
With oil filter cartridge replacement
Oil pressure (hot)
Dry sump
YAMALUBE 4 (20W40) or SAE20W40
API service SE, SF, SG type or higher
5.20 L (5.50 US qt) (4.58 Imp.qt)
3.2 L (3.38 US qt) (2.82 Imp.qt)
2.0 L (2.11 US qt) (1.76 Imp.qt)
4.10 L (4.33 US qt) (3.61 Imp.qt)
4.90 L (5.18 US qt) (4.31 Imp.qt)
60.0 kPa/900 r/min (8.7 psi/900 r/min) (0.60
kgf/cm/900 r/min)
Transfer gear oil

Type
Quantity (disassembled)
Quantity
SAE80 API GL-4 Hypoid gear oil

0.60 L (0.63 US qt) (0.53 Imp.qt)
0.55 L (0.58 US qt) (0.48 Imp.qt)
Oil filter
Oil filter type
Cartridge (paper)
Oil pump
Oil pump type
Inner-rotor-to-outer-rotor-tip clearance
Limit
Outer-rotor-to-oil-pump-housing clearance
Limit
Oil-pump-housing-to-inner-and-outer-rotor
clearance
Limit
Bypass valve opening pressure
Trochoid
Less than 0.12 mm (0.0047 in)
0.20 mm (0.0079 in)
0.090.19 mm (0.00350.0075 in)
0.26 mm (0.0102 in)
0.060.13 mm (0.00240.0051 in)
0.20 mm (0.0079 in)
80.0120.0 kPa (11.617.4 psi) (0.801.20
kgf/cm)
600.0 kPa (87.0 psi) (6.00 kgf/cm)
Relief valve operating pressure

Transfer gear oil pump
Oil pump type
Inner-rotor-to-outer-rotor-tip clearance
Trochoid
2-2
Limit
Limit
Oil-pump-housing-to-inner-and-outer-rotor
clearance
Limit
0.20 mm (0.0079 in)

0.100.15 mm (0.00390.0059 in)
0.22 mm (0.0087 in)
0.040.09 mm (0.00160.0035 in)
0.160 mm (0.0063 in)
Spark plug (s)

Manufacturer/model
Manufacturer/model
Spark plug gap
NGK/DPR8EA-9
DENSO/X24EPR-U9
0.80.9 mm (0.0310.035 in)
Cylinder head
Volume
Warpage limit
80.9084.90 cm (4.945.18 cu.in)

0.03 mm (0.0012 in)
Camshaft
Drive system
Crankcase hole inside diameter
Camshaft journal diameter (crankcase side)
Camshaft to crankcase clearance
Camshaft cover hole inside diameter
Camshaft journal diameter (camshaft cover side)
Camshaft to camshaft cover clearance
Camshaft lobe dimensions
Intake A
Limit
Intake B
Limit
Exhaust A
Limit
Exhaust B
Limit
2-3
Gear drive
25.00025.021 mm (0.98430.9851 in)
24.95724.980 mm (0.98260.9835 in)
0.0200.064 mm (0.00080.0025 in)
28.00028.021 mm (1.10241.1032 in)
27.95727.980 mm (1.10071.1016 in)
0.0200.064 mm (0.00080.0025 in)
42.53242.632 mm (1.67451.6784 in)
42.432 mm (1.6705 in)
35.95036.050 mm (1.41541.4193 in)
35.850 mm (1.4114 in)
42.53042.630 mm (1.67441.6783 in) (cylinder
#1)
42.53142.631 mm (1.67441.6784 in) (cylinder
#2)
42.430 mm (1.6705 in) (cylinder #1)
42.431 mm (1.6705 in) (cylinder #2)
35.95036.050 mm (1.41541.4193 in)
35.850 mm (1.4114 in)
Rocker arm/rocker arm shaft

Rocker arm inside diameter
Limit
Rocker arm shaft outside diameter
Rocker-arm-to-rocker-arm-shaft clearance
Limit
18.00018.018 mm (0.70870.7094 in)

18.036 mm (0.7101 in)
17.97617.991 mm (0.70770.7083 in)
0.0090.042 mm (0.00040.0017 in)
0.080 mm (0.0032 in)
Valve, valve seat, valve guide

Valve clearance (cold)
Intake
Exhaust
Valve dimensions
Valve head diameter A (intake)
Valve head diameter A (exhaust)
0.000.04 mm (0.00000.0016 in)

0.000.04 mm (0.00000.0016 in)
35.9036.10 mm (1.41341.4213 in)
30.9031.10 mm (1.21651.2244 in)
A
Valve seat width C (intake)
Limit
Valve seat width C (exhaust)
Limit
1.101.30 mm (0.04330.0512 in)

2.0 mm (0.08 in)
1.101.30 mm (0.04330.0512 in)
2.0 mm (0.08 in)
C
Valve margin thickness D (intake)
Limit
Valve margin thickness D (exhaust)
Limit
1.151.45 mm (0.04530.0571 in)

0.4 mm (0.02 in)
1.151.45 mm (0.04530.0571 in)
0.4 mm (0.02 in)
D
Valve stem diameter (intake)
Limit
Valve stem diameter (exhaust)
Limit
Valve guide inside diameter (intake)
Limit
Valve guide inside diameter (exhaust)
Limit
Valve-stem-to-valve-guide clearance (intake)
Limit
Valve-stem-to-valve-guide clearance (exhaust)
Limit
2-4
5.9755.990 mm (0.23520.2358 in)

5.945 mm (0.2341 in)
5.9605.975 mm (0.23460.2352 in)
5.920 mm (0.2331 in)
6.0006.012 mm (0.23620.2367 in)
6.050 mm (0.2382 in)
6.0006.012 mm (0.23620.2367 in)
6.050 mm (0.2382 in)
0.0100.037 mm (0.00040.0015 in)
0.080 mm (0.0032 in)
0.0250.052 mm (0.00100.0020 in)
0.100 mm (0.0039 in)
Valve stem runout
0.010 mm (0.0004 in)
Valve spring
Free length (intake)
Limit
Free length (exhaust)
Limit
Installed length (intake)
Installed length (exhaust)
Spring rate K1 (intake)
Spring rate K2 (intake)
Spring rate K1 (exhaust)
Spring rate K2 (exhaust)
Installed compression spring force (intake)
Spring tilt (intake)

Spring tilt (exhaust)
46.71 mm (1.84 in)

44.71 mm (1.76 in)
46.71 mm (1.84 in)
44.71 mm (1.76 in)
32.66 mm (1.29 in)
32.66 mm (1.29 in)
16.58 N/mm (94.67 lb/in) (1.69 kgf/mm)
21.98 N/mm (125.51 lb/in) (2.24 kgf/mm)
16.58 N/mm (94.67 lb/in) (1.69 kgf/mm)
21.98 N/mm (125.51 lb/in) (2.24 kgf/mm)
217.00249.00 N (48.7855.98 lb) (22.13
25.39 kgf)
217.00249.00 N (48.7855.98 lb) (22.13
25.39 kgf)
2.5 /2.0 mm
2.5 /2.0 mm
Winding direction (intake)

Winding direction (exhaust)
Clockwise
Clockwise
Installed compression spring force (exhaust)
Valve lifter
Valve lifter outside diameter (intake)
Valve lifter outside diameter (exhaust)
Valve lifter hole inside diameter (intake)
Valve lifter hole inside diameter (exhaust)
Valve-lifter-to-valve-lifter-hole clearance
22.96222.974 mm (0.90400.9045 in)

22.96222.974 mm (0.90400.9045 in)
23.00023.021 mm (0.90550.9063 in)
23.00023.021 mm (0.90550.9063 in)
0.0260.059 mm (0.00100.0023 in)
Valve push rod

Valve push rod 1 length
Valve push rod 2 length
Valve push rod runout
286.5 mm (11.280 in)

288.5 mm (11.358 in)
0.3 mm (0.012 in)
Cylinder
Bore
Taper limit
Out of round limit
100.000100.010 mm (3.93703.9374 in)

0.050 mm (0.0020 in)
0.050 mm (0.0020 in)
2-5
Piston
Piston-to-cylinder clearance
Limit
Diameter D
Height H
0.0250.050 mm (0.00100.0020 in)

0.15 mm (0.0059 in)
99.96099.975 mm (3.93543.9360 in)
10.0 mm (0.39 in)
H
D
Offset
Piston pin bore inside diameter
Limit
Piston pin outside diameter
Limit
Piston-pin-to-piston-pin-bore clearance
Limit
0.50 mm (0.0197 in)

23.00423.015 mm (0.90570.9061 in)
23.045 mm (0.9073 in)
22.99123.000 mm (0.90520.9055 in)
22.971 mm (0.9044 in)
0.0040.024 mm (0.000160.00094 in)
0.074 mm (0.00291 in)
Piston ring
Top ring
Ring type
Dimensions (B T)
Barrel
1.20 3.80 mm (0.05 0.15 in)
B
T
End gap (installed)
Limit
Ring side clearance
Limit
2nd ring
Ring type
Dimensions (B T)
0.200.35 mm (0.00790.0138 in)

0.55 mm (0.0217 in)
0.0300.080 mm (0.00120.0032 in)
0.120 mm (0.0047 in)
Taper
1.20 4.00 mm (0.05 0.16 in)
B
T
End gap (installed)
Limit
Ring side clearance
Limit
0.450.60 mm (0.01770.0236 in)

0.95 mm (0.0374 in)
0.0300.070 mm (0.00120.0028 in)
0.120 mm (0.0047 in)
2-6
Oil ring
Dimensions (B T)
2.50 3.40 mm (0.10 0.13 in)
B
T
End gap (installed)
0.200.70 mm (0.00790.0276 in)
Connecting rod
Oil clearance (using plastigauge)
Bearing color code
0.0500.074 mm (0.00200.0029 in)

1.Blue 2.Black 3.Brown 4.Green 5.Yellow
Crankshaft
Width A
Runout limit C
Big end side clearance D
Big end radial clearance E
Limit
105.80106.20 mm (4.1654.181 in)

0.040 mm (0.0016 in)
0.3200.474 mm (0.01260.0187 in)
0.0370.074 mm (0.00150.0029 in)
0.09 mm (0.0035 in)
Journal oil clearance (using plastigauge)

Limit
0.0300.060 mm (0.00120.0024 in)

0.10 mm (0.0039 in)
Clutch
Clutch type
Clutch release method
Operation
Friction plate 1, 3 thickness
Wear limit
Plate quantity
Friction plate 2 thickness
Wear limit
Plate quantity
Clutch plate thickness
Plate quantity
Warpage limit
Clutch spring free length
Minimum length
Spring quantity
Clutch housing thrust clearance
Clutch housing radial clearance
Wet, multiple-disc
Hydraulic inner push
Left hand operation
2.903.10 mm (0.1140.122 in)
2.80 mm (0.110 in)
10 pcs
2.923.08 mm (0.1150.121 in)
2.82 mm (0.111 in)
1 pcs
1.902.10 mm (0.0750.083 in)
10 pcs
0.20 mm (0.0079 in)
6.78 mm (0.27 in)
6.28 mm (0.25 in)
1 pcs
0.1000.110 mm (0.00390.0043 in)
0.0200.066 mm (0.00080.0026 in)
Transmission
Transmission type
Constant mesh 5-speed
2-7
Primary reduction system
Primary reduction ratio
Secondary reduction system
Secondary reduction ratio
Operation
Gear ratio
1st
2nd
3rd
4th
5th
Main axle runout limit
Drive axle runout limit
Spur gear
72/51 (1.412)
Belt drive
70/31 (2.258)
Left foot operation
38/16 (2.375)
33/21 (1.571)
29/25 (1.160)
26/28 (0.929)
24/30 (0.800)
0.08 mm (0.0032 in)
0.08 mm (0.0032 in)
Shifting mechanism
Shift mechanism type
Shift fork guide bar bending limit
Shift fork thickness
Guide bar
0.025 mm (0.0010 in)
6.266.39 mm (0.24650.2516 in)
Air filter
Air filter element
Oil-coated paper element
Fuel pump
Pump type
Model/manufacturer
Maximum consumption amperage
Output pressure
Electrical
1D7/MITSUBISHI
5.5 A
441.0637.0 kPa (63.992.4 psi) (4.416.37
kgf/cm)
Fuel injection
Model/quantity
Manufacturer
INP-101/2
NIPPON INJECTOR
Throttle body
Type/quantity
Manufacturer
ID mark
AC43/2
MIKUNI
XV19MV/XV19SV/XV19V/XV19CTMV/
XV19CTSV/XV19CTV:
1D71 00
XV19MVC/XV19SVC/XV19VC/XV19CTMVC/
XV19CTSVC/XV19CTVC:
1D72 10
#100
Throttle valve size

Throttle position sensor
Resistance
Output voltage (at idle)
4.06.0 k/blue-black
0.630.73 V
Fuel injection sensor

Crankshaft position sensor resistance
Intake air pressure sensor output voltage
Engine temperature sensor resistance
248372
3.754.25 V
0.901.10 k at 100 C (212 F)
2-8
Idling condition
Engine idling speed
Intake vacuum
850950 r/min
31.335.3 kPa (9.310.4 inHg) (235265
mmHg)
80.090.0 C (176.00194.00 F)
4.06.0 mm (0.160.24 in)
Oil temperature
Throttle cable free play
2-9
CHASSIS SPECIFICATIONS
EAS20300
Chassis
Frame type
Caster angle
Trail
Double cradle
31.20
152.0 mm (5.98 in)
Front wheel
Wheel type
Rim size
Rim material
Wheel travel
Radial wheel runout limit
Lateral wheel runout limit
Cast wheel
18M/C MT4.00
Aluminum
130.0 mm (5.12 in)
1.0 mm (0.04 in)
0.5 mm (0.02 in)
Rear wheel
Wheel type
Rim size
Rim material
Wheel travel
Cast wheel
17M/C MT5.50
Aluminum
110.0 mm (4.33 in)
1.0 mm (0.04 in)
0.5 mm (0.02 in)
Front tire
Type
Size
Manufacturer/model
Manufacturer/model
Wear limit (front)
Tubeless
130/70R18M/C 63H
DUNLOP/D251F
BRIDGESTONE/G851 RADIAL G
1.0 mm (0.04 in)
Rear tire
Type
Size
Manufacturer/model
Manufacturer/model
Wear limit (rear)
Tubeless
190/60R17M/C 78H
DUNLOP/D251
1.0 mm (0.04 in)
Tire air pressure (measured on cold tires)

Loading condition
Front
Rear
Loading condition
090 kg (0198 lb)

250 kPa (36 psi) (2.50 kgf/cm)
280 kPa (41 psi) (2.80 kgf/cm)
90210 kg (198463 lb)
90186 kg (198410 lb)
250 kPa (36 psi) (2.50 kgf/cm)
280 kPa (41 psi) (2.80 kgf/cm)
Front
Rear
High-speed riding
Front
Rear
250 kPa (36 psi) (2.50 kgf/cm)

280 kPa (41 psi) (2.80 kgf/cm)
2-10
Front brake
Type
Operation
Front disc brake
Disc outside diameter thickness
Brake disc thickness limit
Brake disc deflection limit
Brake pad lining thickness (inner)
Limit
Brake pad lining thickness (outer)
Limit
Master cylinder inside diameter
Caliper cylinder inside diameter
Recommended fluid
Dual disc brake

Right hand operation
298.0 5.0 mm (11.73 0.20 in)
4.5 mm (0.18 in)
0.10 mm (0.0039 in)
5.5 mm (0.22 in)
0.5 mm (0.02 in)
5.5 mm (0.22 in)
0.5 mm (0.02 in)
14.00 mm (0.55 in)
27.00 mm (1.06 in)
30.23 mm (1.19 in)
DOT 4
Rear brake
Type
Operation
Brake pedal position
Rear disc brake
Disc outside diameter thickness
Limit
Limit
Master cylinder inside diameter
Recommended fluid
320.0 6.0 mm (12.60 0.24 in)

5.5 mm (0.22 in)
0.15 mm (0.0059 in)
5.8 mm (0.23 in)
0.8 mm (0.03 in)
5.8 mm (0.23 in)
0.8 mm (0.03 in)
12.7 mm (0.50 in)
41.30 mm (1.63 in)
DOT 4
Steering
Steering bearing type
Lock to lock angle (left)
Lock to lock angle (right)
Taper roller bearing

35.0
35.0
Front suspension
Type
Spring/shock absorber type
Front fork travel
Fork spring free length
Limit
Collar length
Installed length
Spring rate K1
Spring stroke K1
Spring rate K2
Spring stroke K2
Inner tube outer diameter
Inner tube bending limit
Optional spring available
Telescopic fork
Coil spring/oil damper
130.0 mm (5.12 in)
273.9 mm (10.78 in)
268.4 mm (10.57 in)
230.0 mm (9.06 in)
268.9 mm (10.59 in)
10.0 N/mm (57.1 lb/in) (1.02 kgf/mm)
0.030.0 mm (0.001.18 in)
12.0 N/mm (68.5 lb/in) (1.22 kgf/mm)
30.0130.0 mm (1.185.12 in)
46.0 mm (1.81 in)
0.2 mm (0.01 in)
No
Single disc brake

Right foot operation
110.0 mm (4.33 in)
2-11
Recommended oil
Quantity
Level
Fork oil 10WT

571.0 cm (19.31 US oz) (20.10 Imp.oz)
124.0 mm (4.88 in)
Rear suspension
Type
Spring/shock absorber type
Rear shock absorber assembly travel
Spring free length
Limit
Installed length
Swingarm (link suspension)

Coil spring/gas-oil damper
50.0 mm (1.97 in)
180.0 mm (7.09 in)
176.4 mm (6.94 in)
171.0 mm (6.73 in)
165.0 mm (6.50 in)
176.50 N/mm (1007.82 lb/in) (18.00 kgf/mm)
0.050.0 mm (0.001.97 in)
No
0.98 MPa (139.4 psi) (9.8 kgf/cm)
Installed spring length
162.0 mm (6.38 in)
171.0 mm (6.73 in)
165.0 mm (6.50 in)
171.0 mm (6.73 in)
Spring rate K1
Spring stroke K1
Optional spring available
Enclosed gas/air pressure (STD)
Spring preload adjusting positions
Minimum
Standard
Maximum
Swingarm
Swingarm end free play limit (radial)
Swingarm end free play limit (axial)
1.0 mm (0.04 in)

1.0 mm (0.04 in)
Drive belt
Model/manufacturer
Drive belt slack (on the sidestand)
Drive belt slack (on a suitable stand)
UBD-0732/GATES CORPORATION
7.513 mm (0.300.51 in)
1421 mm (0.550.83 in)
2-12
ELECTRICAL SPECIFICATIONS
EAS20310
Voltage
System voltage
12 V
Ignition system
Ignition system
Advancer type
Ignition timing (B.T.D.C.)
Transistorized coil ignition (digital)

Electric
10.0 /900 r/min
Engine control unit

Model/manufacturer
F008T83271/MITSUBISHI
Ignition coil
Model/manufacturer
Minimum ignition spark gap
Primary coil resistance
Secondary coil resistance
2JN/MORIC
6.0 mm (0.24 in)
2.162.64
8.6412.96 k
Spark plug cap

Material
Resistance
Resin
10.0 k
AC magneto
Model/manufacturer
Standard output
Stator coil resistance
F4T38971/MITSUBISHI
14.0 V 32.0 A 5000 r/min
0.1120.168
Voltage regulator
Rectifier/regulator
Regulator type
Model/manufacturer
No load regulated voltage
Rectifier capacity
Withstand voltage
Semi conductor-short circuit

FH012AA/SHINDENGEN
14.214.8 V
50.0 A
40.0 V
Battery
Model
Voltage, capacity
Manufacturer
Ten hour rate amperage
GT14B-4
12 V, 12.0 Ah
GS YUASA
1.20 A
Headlight
Bulb type
Halogen bulb
Bulb voltage, wattage quantity

Low beam headlight
High beam headlight
Tail/brake light
Front turn signal/position light
Rear turn signal light
License plate light
12 V, 51.0 W 1
12 V, 55.0 W 1
LED
12 V, 23 W/8.0 W 2
12 V, 21.0 W 2
12 V, 5.0 W
2-13
Meter lighting
LED
Indicator light
Neutral indicator light
Turn signal indicator light
High beam indicator light
Fuel level warning light
Engine trouble warning light
LED
LED
LED
LED
LED
Electric starting system

System type
Constant mesh
Starter motor
Model/manufacturer
Power output
Armature coil resistance
Brush overall length
Limit
Brush spring force
Commutator diameter
Limit
Mica undercut (depth)
1D7/YAMAHA
0.90 kW
0.00810.0099
9.8 mm (0.39 in)
5.00 mm (0.20 in)
7.3611.04 N (26.4939.74 oz) (7501126 gf)
28.5 mm (1.12 in)
27.5 mm (1.08 in)
1.50 mm (0.06 in)
Starter relay
Model/manufacturer
Amperage
Coil resistance
2768079-A/JIDECO
180.0 A
4.184.62
Horn
Horn type
Quantity
Model/manufacturer
Maximum amperage
Coil resistance
Performance
Eddy
2 pcs
YP-12/NIKKO
2.0 A
0.940.98
95115 dB/2m
Turn signal relay

Relay type
Model/manufacturer
Built-in, self-canceling device
Turn signal blinking frequency
Wattage
Semi transistor
FB246H/DENSO
Yes
75.095.0 cycles/min
21(23) W 2 + LED 2
Fuel gauge
Model/manufacturer
Sender unit resistance (full)
Sender unit resistance (empty)
1D7/YAMAHA
911
213219
Starting circuit cut-off relay

Model/manufacturer
Coil resistance
G8R-30Y-V3/OMRON
162198
2-14
Headlight relay
Model/manufacturer
ACM33211M05/MATSUSHITA
Fuel pump relay

Model/manufacturer
Coil resistance
G8R-30Y-V3/OMRON
162198
Thermo unit
Model/manufacturer
Resistance at 100C
5PX/DENSO
898.41098.0
Fuses
Main fuse
Headlight fuse
Taillight fuse
Signaling system fuse
Ignition fuse
Auxiliary DC connector fuse
ECU fuse
Fuel injection system fuse
Backup fuse
Reserve fuse
Reserve fuse
Reserve fuse
Reserve fuse
Reserve fuse
50.0 A
20.0 A
10.0 A
10.0 A
25.0 A
3.0 A
10.0 A
15.0 A
10.0 A
25.0 A
20.0 A
15.0 A
10.0 A
3.0 A
2-15
TIGHTENING TORQUES
EAS20320
TIGHTENING TORQUES
EAS20330
GENERAL TIGHTENING TORQUE

SPECIFICATIONS
This chart specifies tightening torques for standard fasteners with a standard ISO thread pitch.
Tightening torque specifications for special components or assemblies are provided for each
chapter of this manual. To avoid warpage, tighten multi-fastener assemblies in a crisscross pattern and progressive stages until the specified
tightening torque is reached. Unless otherwise
specified, tightening torque specifications require clean, dry threads. Components should be
at room temperature.
A. Distance between flats

B. Outside thread diameter
A (nut) B (bolt)
General tightening
torques
Nm
mkg
ftlb
10 mm
6 mm
0.6
4.3
12 mm
8 mm
15
1.5
11
14 mm
10 mm
30
3.0
22
17 mm
12 mm
55
5.5
40
19 mm
14 mm
85
8.5
61
22 mm
16 mm
130
13.0
94
2-16
TIGHTENING TORQUES
EAS20340
ENGINE TIGHTENING TORQUES

Item
Thread
Qty
size
Tightening torque
Cylinder head nut
M12
60 Nm (6.0 mkg, 43 ftlb)
Cylinder head stud bolt (exhaust

pipe)
M8
15 Nm (1.5 mkg, 11 ftlb)
Spark plug
M12
18 Nm (1.8 mkg, 13 ftlb)
Engine temperature sensor
20 Nm (2.0 mkg, 14 ftlb)
Rocker arm base bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Rocker arm base bolt
M8
24 Nm (2.4 mkg, 17 ftlb)
Cylinder head cover bolt
M6
28
10 Nm (1.0 mkg, 7.2 ftlb)
Connecting rod bolt (1st)
M8
15 Nm (1.5 mkg, 11 ftlb)
Remarks
E
See
NOTE.
M
Connecting rod bolt (final)
M8
Specified angle 125135
See
NOTE.
M
Right balancer driven gear bolt
M10
40 Nm (4.0 mkg, 29 ftlb)
Left balancer drive gear bolt
M10
40 Nm (4.0 mkg, 29 ftlb)
Left balancer driven gear housing

screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Left balancer weight bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Left balancer idle gear shaft bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Camshaft driven gear bolt
M10
60 Nm (6.0 mkg, 43 ftlb)
Camshaft drive gear bolt
M10
60 Nm (6.0 mkg, 43 ftlb)
Front cylinder camshaft gear bolt
M10
40 Nm (4.0 mkg, 29 ftlb)
Locknut (rocker arm adjusting

screw)
M7
20 Nm (2.0 mkg, 14 ftlb)
Valve lifter case bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Oil filter bolt
M18
70 Nm (7.0 mkg, 50 ftlb)
Oil filter cartridge
M20
17 Nm (1.7 mkg, 12 ftlb)
Oil pipe 1 union bolt
M10
21 Nm (2.1 mkg, 15 ftlb)
Oil pipe 1 union bolt
M8
18 Nm (1.8 mkg, 13 ftlb)
Oil filter bracket bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Oil pipe bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Oil delivery pipe 2 bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Engine oil pump driven gear

stopper bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Oil pipe 3 bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Oil pump bolt (crankcase)
M8
24 Nm (2.4 mkg, 17 ftlb)
2-17
LT
LT
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Oil pipe 2 bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Oil pipe 4 bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Oil pump housing cover 1 screw

(crankcase)
M6
7 Nm (0.7 mkg, 5.1 ftlb)

(crankcase)
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Throttle body joint clamp screw
M5
3 Nm (0.3 mkg, 2.2 ftlb)
Pressure regulator bolt
M5
7 Nm (0.7 mkg, 5.1 ftlb)
Intake manifold assembly bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Fuel pipe bolt
M12
30 Nm (3.0 mkg, 22 ftlb)
Rear exhaust pipe joint nut
M8
20 Nm (2.0 mkg, 14 ftlb)
Rear exhaust pipe, rear exhaust

pipe joint cover and rear exhaust
pipe joint nut
M8
24 Nm (2.4 mkg, 17 ftlb)
Front exhaust pipe nut
M8
20 Nm (2.0 mkg, 14 ftlb)
Front exhaust pipe and rear exhaust pipe bolt
M8
20 Nm (2.0 mkg, 14 ftlb)
Rear exhaust pipe and muffler

bolt
M8
20 Nm (2.0 mkg, 14 ftlb)
Locknut (EXUP cable)
M6
7 Nm (0.7 mkg, 5.1 ftlb)
EXUP valve pulley cover bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Rear exhaust pipe joint cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Muffler and muffler bracket bolt
M8
29 Nm (2.9 mkg, 21 ftlb)
Muffler bracket and frame bolt
M10
53 Nm (5.3 mkg, 38 ftlb)
O2 sensor
M18
44 Nm (4.4 mkg, 32 ftlb)
Crankcase stud bolt
M12
See NOTE.
Crankcase bolt
M6
21
10 Nm (1.0 mkg, 7.2 ftlb)
Crankcase bolt
M8
24 Nm (2.4 mkg, 17 ftlb)
Oil baffle plate bolt (left crankcase)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Crankcase stud bolt
M10
See NOTE.
Nozzle
M6
0.5 Nm (0.05 mkg, 0.36 ftlb)
Oil gallery screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Bearing housing bolt (torque limiter)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Oil gallery bolt
M8
20 Nm (2.0 mkg, 14 ftlb)
LT
Engine oil drain bolt (crankcase)
M14
43 Nm (4.3 mkg, 31 ftlb)
Stator coil lead holder screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Crankshaft position sensor lead

holder screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
2-18
LT
LT
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Clutch cover damper plate screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Camshaft cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Generator damper cover bolt
M5
5 Nm (0.5 mkg, 3.6 ftlb)
Engine oil filler plug
M20
10 Nm (1.0 mkg, 7.2 ftlb)
Camshaft sprocket cover plate

bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Oil baffle plate bolt (right crankcase)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Clutch cover plate bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Generator cover bolt
M6
10
10 Nm (1.0 mkg, 7.2 ftlb)
Camshaft sprocket cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Clutch cover bolt
M6
18
10 Nm (1.0 mkg, 7.2 ftlb)
Oil gallery bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Clutch damper cover plate bolt
M5
5 Nm (0.5 mkg, 3.6 ftlb)
Clutch damper cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Starter clutch bolt
M8
24 Nm (2.4 mkg, 17 ftlb)
Generator rotor bolt
M12
80 Nm (8.0 mkg, 58 ftlb)
Starter motor bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Primary drive gear bolt
M12
105 Nm (10.5 mkg, 75 ftlb)
Clutch boss nut
M20
105 Nm (10.5 mkg, 75 ftlb)
Clutch spring plate retainer bolt
M6
8 Nm (0.8 mkg, 5.8 ftlb)
Bleed screw (clutch release cylinder)
M8
6 Nm (0.6 mkg, 4.3 ftlb)
Clutch release cylinder bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Drive axle bearing retainer screw
M8
20 Nm (2.0 mkg, 14 ftlb)
Main axle bearing retainer screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Engine oil drain bolt (oil tank)
M14
43 Nm (4.3 mkg, 31 ftlb)
Transfer gear oil drain bolt
M8
18 Nm (1.8 mkg, 13 ftlb)
Middle drive gear nut
M22
140 Nm (14.0 mkg, 100 ftlb)
LT
LT
LT
Stake
E
Stake
LT
Stake
E
Transfer gear case oil pump assembly nut
M10
40 Nm (4.0 mkg, 29 ftlb)
Transfer gear case oil pump assembly bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Oil pump housing screw (transfer

gear case)
M5
4 Nm (0.4 mkg, 2.9 ftlb)
Transfer gear oil check bolt
M6
8 Nm (0.8 mkg, 5.8 ftlb)
Transfer gear case bolt
M10
50 Nm (5.0 mkg, 36 ftlb)
2-19
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Dipstick joint bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Drive pulley case bolt
M10
70 Nm (7.0 mkg, 50 ftlb)
Oil strainer bolt (oil tank)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Oil pipe 5 bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Transfer gear case cover plate

bolt
M6
5 Nm (0.5 mkg, 3.6 ftlb)
Transfer gear case cover bolt
M6
12
10 Nm (1.0 mkg, 7.2 ftlb)
Oil tank cover bolt
M6
15
10 Nm (1.0 mkg, 7.2 ftlb)
Oil tank bracket bolt
M8
28 Nm (2.8 mkg, 20 ftlb)
Shift shaft spring stopper bolt
M8
22 Nm (2.2 mkg, 16 ftlb)
LT
Stopper lever bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Crankshaft position sensor screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Neutral switch screw
M6
4 Nm (0.4 mkg, 2.9 ftlb)
LT
Stator coil screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Neutral switch lead clamp screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Speed sensor bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Oil cooler bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Oil cooler bracket bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Oil cooler hose bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Clutch hose union bolt
M10
30 Nm (3.0 mkg, 22 ftlb)
Clutch pipe union bolt
M10
10 Nm (1.0 mkg, 7.2 ftlb)
Clutch pipe holder bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Clutch pipe joint nut
M10
19 Nm (1.9 mkg, 13 ftlb)
LT
NOTE:
Tighten the connecting rod bolts to 15 Nm (1.5 mkg, 11 ftlb), and then tighten them further to reach
the specified angle 125135.
Install the crankcase stud bolts (M12) so that their installed length is 141.5 mm (5.57 in).
Install the crankcase stud bolts (M10) so that their installed length is 70.5 mm (2.78 in).
2-20
TIGHTENING TORQUES
Cylinder head tightening sequence:
B
1
3
A. Front cylinder
B. Rear cylinder
2-21
TIGHTENING TORQUES
EAS20350
CHASSIS TIGHTENING TORQUES

Item
Thread
Qty
size
Tightening torque
Engine mounting bolt (left upper

side)
M12
66 Nm (6.6 mkg, 48 ftlb)
Engine mounting bolt (right upper

side)
M12
59 Nm (5.9 mkg, 43 ftlb)
Engine mounting nut (rear upper

side)
M12
98 Nm (9.8 mkg, 71 ftlb)
Engine mounting spacer bolt
M18
18 Nm (1.8 mkg, 13 ftlb)
Engine bracket bolt (left upper

side)
M10
53 Nm (5.3 mkg, 38 ftlb)
Engine bracket bolt (right upper

side)
M10
53 Nm (5.3 mkg, 38 ftlb)
Engine bracket nut (rear upper

side)
M10
53 Nm (5.3 mkg, 38 ftlb)
Engine mounting nut (front upper

side)
M12
98 Nm (9.8 mkg, 71 ftlb)
Engine mounting nut (rear lower

side)
M12
98 Nm (9.8 mkg, 71 ftlb)
Engine mounting nut (front lower

side)
M12
105 Nm (10.5 mkg, 75 ftlb)
Engine bracket nut (front upper

side)
M10
53 Nm (5.3 mkg, 38 ftlb)
Engine cross-member bracket

bolt
M10
30 Nm (3.0 mkg, 22 ftlb)
Engine bracket nut (left rear lower side)
M10
58 Nm (5.8 mkg, 42 ftlb)
Engine bracket bolt (right rear

lower side)
M10
53 Nm (5.3 mkg, 38 ftlb)
Transfer gear case bracket and

transfer gear case bolt
M10
63 Nm (6.3 mkg, 45 ftlb)
Transfer gear case bracket and

frame bolt
M10
53 Nm (5.3 mkg, 38 ftlb)
Cylinder-#1 ignition coil bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Cylinder-#2 ignition coil bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Lean angle sensor bolt
M4
2 Nm (0.2 mkg, 1.4 ftlb)
Horn bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
ISC (idle speed control) unit bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
ISC (idle speed control) unit

bracket bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Pivot shaft nut
M18
125 Nm (12.5 mkg, 90 ftlb)
Relay arm nut (relay arm and

swingarm)
M12
59 Nm (5.9 mkg, 43 ftlb)
2-22
Remarks
LT
LT
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Relay arm nut (relay arm and

connecting arm)
M12
59 Nm (5.9 mkg, 43 ftlb)
Rear shock absorber assembly

nut (rear side)
M10
40 Nm (4.0 mkg, 29 ftlb)

nut (front side)
M12
59 Nm (5.9 mkg, 43 ftlb)
Upper drive belt cover bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Lower drive belt cover bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Rear brake hose guide bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Upper bracket pinch bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Headlight cover bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Headlight bracket and throttle cable guide bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Headlight body bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Steering stem nut
M28
115 Nm (11.5 mkg, 85 ftlb)
Upper handlebar holder bolt
M8
28 Nm (2.8 mkg, 20 ftlb)
Lower ring nut (initial tightening

torque)
M30
52 Nm (5.2mkg, 37 ftlb)
See
NOTE.
Lower ring nut (final tightening

torque)
M30
18 Nm (1.8 mkg, 13 ftlb)
See
NOTE.
Hose guide and lower handlebar

holder nut
M10
32 Nm (3.2 mkg, 23 ftlb)
Front brake master cylinder holder bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Front brake hose union bolt (front

brake master cylinder side)
M10
30 Nm (3.0 mkg, 22 ftlb)
Clutch master cylinder holder bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Grip end
M16
23 Nm (2.3 mkg, 17 ftlb)
Lower handlebar holder nut
M10
50 Nm (5.0 mkg, 36 ftlb)
LT
Upper bracket cover bolt
M8
19 Nm (1.9 mkg, 13 ftlb)
LT
M8
16 Nm (1.6 mkg, 11 ftlb)
LT
Front brake hose guide and front

brake hose guide bracket bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Front brake hose guide and lower

bracket bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Front brake hose joint bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Bolt (lower bracket hole)
M8
16 Nm (1.6 mkg, 11 ftlb)
Front fender stay bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
LT
Front fender bolt
M8
16 Nm (1.6 mkg, 11 ftlb)
LT
Fuel sender bolt
M5
4 Nm (0.4 mkg, 2.9 ftlb)
2-23
LT
LT
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Fuel tank bracket bolt (front side)
M8
16 Nm (1.6 mkg, 11 ftlb)
Fuel tank bracket nut (rear side)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Sub-fuel tank bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Rider seat bracket bolt
M8
23 Nm (2.3 mkg, 17 ftlb)
Fuel tank and fuel tank bracket

bolt (front side)
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Fuel tank and fuel tank bracket

bolt (rear side)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Meter cover bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Fuel pump bolt
M5
5 Nm (0.5 mkg, 3.6 ftlb)
Fuel return pipe holder bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Air filter case bracket bolt
M8
16 Nm (1.6 mkg, 11 ftlb)
Canister bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Front wheel axle
M18
72 Nm (7.2 mkg, 52 ftlb)
Front wheel axle pinch bolt
M8
23 Nm (2.3 mkg, 17 ftlb)
Rear wheel axle nut
M18
150 Nm (15.0 mkg, 110 ftlb)
Locknut (drive belt adjusting bolt)
M8
16 Nm (1.6 mkg, 11 ftlb)
Front brake caliper bolt
M10
40 Nm (4.0 mkg, 29 ftlb)
Front brake hose union bolt (front

brake caliper side)
M10
32 Nm (3.2 mkg, 23 ftlb)
Rear brake caliper bolt
M10
27 Nm (2.7 mkg, 19 ftlb)
Front brake disc bolt
M6
12
23 Nm (2.3 mkg, 17 ftlb)
LT
Rear brake disc bolt
M6
18 Nm (1.8 mkg, 13 ftlb)
LT
Bleed screw (front brake caliper)
M8
6 Nm (0.6 mkg, 4.3 ftlb)
Bleed screw (rear brake caliper)
M7
6 Nm (0.6 mkg, 4.3 ftlb)
Rear wheel pulley nut
M12
95 Nm (9.5 mkg, 68 ftlb)
Left side cover and sub-fuel tank

bracket bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Left side cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Seat lock cable assembly bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Lead holder bracket bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Right side cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Starter motor lead bolt (starter

relay side)
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Positive battery lead bolt (starter

relay side)
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Rear fender bracket and frame

bolt
M10
40 Nm (4.0 mkg, 29 ftlb)
2-24
LT
For California
only
LS
LT
LT
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Rear fender bracket and frame

bolt
M10
40 Nm (4.0 mkg, 29 ftlb)
Rear fender bracket and rear

fender bolt
M8
23 Nm (2.3 mkg, 17 ftlb)
Passenger seat bolt
M8
16 Nm (1.6 mkg, 11 ftlb)
Rider seat bracket assembly and

seat lock assembly bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Tool kit and battery box bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Pressure regulator bracket bolt
M6
13 Nm (1.3 mkg, 9.4 ftlb)
Cylinder-#1 ignition coil cover

bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Cylinder-#1 ignition coil bracket

bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
License plate bolt
M8
16 Nm (1.6 mkg, 11 ftlb)
Sidestand bolt
M10
63 Nm (6.3 mkg, 45 ftlb)
LT
Rider footrest assembly bolt (left

and right)
M10
48 Nm (4.8 mkg, 35 ftlb)
LT
Passenger footrest bolt (left and

right)
M10
48 Nm (4.8 mkg, 35 ftlb)
LT
Rear brake master cylinder

bracket and rear brake master
cylinder bolt
M8
23 Nm (2.3 mkg, 17 ftlb)
Rear brake master cylinder

bracket and frame bolt
M8
23 Nm (2.3 mkg, 17 ftlb)
Rear brake master cylinder cover

bolt
M8
16 Nm (1.6 mkg, 11 ftlb)
Brake fluid reservoir and frame

bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Rear brake hose union bolt
M10
30 Nm (3.0 mkg, 22 ftlb)
Rear brake hose holder bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
Shift pedal shaft bracket bolt
M8
16 Nm (1.6 mkg, 11 ftlb)
Locknut (shift rod)
M8
12 Nm (1.2 mkg, 8.7 ftlb)
Shift arm bolt
M6
12 Nm (1.2 mkg, 8.7 ftlb)
Shift pedal bolt (toe side)
M6
18 Nm (1.8 mkg, 13 ftlb)
Shift pedal bolt (heel side)
M6
13 Nm (1.3 mkg, 9.4 ftlb)
Lower bracket pinch bolt
M8
23 Nm (2.3 mkg, 17 ftlb)
Cap bolt
M43
23 Nm (2.3 mkg, 17 ftlb)
Damper rod assembly
M12
40 Nm (4.0 mkg, 29 ftlb)
LT
Lower front fork cover bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
LT
Drive pulley nut
M22
140 Nm (14.0 mkg, 100 ftlb)
Drive pulley cover damper plate

screw
M6
10 Nm (1.0 mkg, 7.2 ftlb)
2-25
LT
LT
Stake
LT
TIGHTENING TORQUES
Item
Thread
Qty
size
Tightening torque
Remarks
Drive pulley cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Rectifier/regulator cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Lead cover bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Rectifier/regulator bolt
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Drive pulley cover plate bolt
M6
5 Nm (0.5 mkg, 3.6 ftlb)
Wire harness guide bolt
M6
7 Nm (0.7 mkg, 5.1 ftlb)
LT
Throttle cable guide bolt (upper

side)
M6
7 Nm (0.7 mkg, 5.1 ftlb)
LT
Throttle cable guide bolt (lower

side)
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Rear shock absorber locknut
M50
30 Nm (3.0 mkg, 22 ftlb)
Windshield holder bracket assembly bolt*
M8
30 Nm (3.0 mkg, 22 ftlb)
Windshield holder nut*
M8
23 Nm (2.3 mkg, 17 ftlb)
Windshield bracket brace nut*
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Windshield brace nut*
M6
10 Nm (1.0 mkg, 7.2 ftlb)
Windshield lock nut*
M24
12 Nm (1.2 mkg, 8.7 ftlb)
Windshield lock cover nut*
M6
8 Nm (0.8 mkg, 5.8 ftlb)
Backrest upper bracket and backrest lower bracket bolt*
M8
23 Nm (2.3 mkg, 17 ftlb)
Backrest pad and backrest upper bracket bolt*
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Backrest pad and backrest upper bracket stay bolt*
M6
10 Nm (1.0 mkg, 7.2 ftlb)
LT
Backrest lock nut*
M24
12 Nm (1.2 mkg, 8.7 ftlb)
Passenger footrest and sidebag

bracket bolt (left and right)*
M10
47 Nm (4.7 mkg, 34 ftlb)
Sidebag bracket bolt*
M8
23 Nm (2.3 mkg, 17 ftlb)
Sidebag bracket brace nut*
M8
23 Nm (2.3 mkg, 17 ftlb)
LT
* For XV19CTSV(C), XV19CTV(C) and XV19CTMV(C)

NOTE:
1. First, tighten the lower ring nut to approximately 52 Nm (5.2 mkg, 37 ftlb) with a torque wrench, then
loosen the lower ring nut completely.
2. Retighten the lower ring nut to 18 Nm (1.8 mkg, 13 ftlb) with a torque wrench.
2-26
LUBRICATION POINTS AND LUBRICANT TYPES

EAS20360

EAS20370
ENGINE
Lubrication point
Lubricant
Oil seal lips
LS
O-rings
LS
Bearings
Cylinder head nuts and washers
Connecting rod small end and big end
Crankshaft journals
Piston surfaces
Piston pins
Connecting rod bolts
Balancer idle gear inner surface and balancer idle gear shaft
Left balancer driven gear inner surface
Right balancer
Gasket (left balancer driven gear housing)
LS
Flange bolts (left balancer drive gear and right balancer driven gear)
Camshaft cam lobes and camshaft journals
Flange bolt (camshaft gear)
Valve push rod end balls
Valve stems (intake and exhaust)
Valve stem ends (intake and exhaust)
Valve lifters
Rocker arms
Rocker arm shafts
Camshaft (front and rear cylinders)
Oil pump rotors (inner and outer) and oil pump housing
LS
Oil pump driven gear shaft
Crankcase stud bolt ends
Starter clutch idle gear shaft
Starter clutch idle gear inner surface
Starter clutch gear inner surface and outer surface
Generator shaft journal
2-27

Lubrication point
Lubricant
Primary driven gear inner surface
Clutch push rods and ball
LS
Clutch boss nut and washer
Transmission gears (wheel and pinion) and collar
Drive pulley nut and washer
Shift forks and shift fork guide bars
Shift drum
Shift shaft and shift shaft oil seal
LS
Shift fork pawl
Crankcase mating surface
Yamaha bond
No.1215 (Three Bond
No.1215)
Stator coil lead grommet
Yamaha bond
No.1215 (Three Bond
No.1215)
Crankshaft position sensor lead grommet
Yamaha bond
No.1215 (Three Bond
No.1215)
2-28

EAS20380
CHASSIS
Lubrication point
Lubricant
Steering bearings and upper bearing dust cover lip
LS
Lower bearing dust seal lip
LS
Front wheel oil seal lips (left and right)
LS
Rear wheel oil seal lips
LS
Rear wheel drive hub oil seal lip
LS
Rear wheel drive hub mating surface
LS
Tube guide (throttle grip) inner surface and throttle cables
LS
Brake lever pivoting point and metal-to-metal moving parts
LS
Clutch lever pivoting point and metal-to-metal moving parts
LS
Brake pedal shaft pivoting point
LS
Shift pedal pivoting point
LS
Passenger footrest pivoting point and ball
LS
Sidestand pivoting point and metal-to-metal moving parts
LS
Dowel pins (rear fender stay)
LS
Pivot shaft
LS
Swingarm pivoting point, collar flange circumference, and oil seal inner
surface
LS
Rear shock absorber bushings and O-rings
LS
Swingarm, relay arm bearings, and oil seal lips
LS
Connecting arm bushings and O-rings
LS
Rear wheel axle
LS
Clutch master cylinder push rod pin and contact surface
LS
2-29
LUBRICATION SYSTEM CHART AND DIAGRAMS

EAS20390

EAS20400
ENGINE OIL LUBRICATION CHART
22
21
20
23
19
18
17
16
15
14
11
14
9
12
10
13
7
8
6
5
4
2
3
2-31

1. Oil strainer (transfer gear case)
2. Oil pump
3. Oil tank
4. Drive axle
5. Main axle
6. Oil strainer (crankcase)
7. Balancer
8. Front cylinder head cover
9. Rear cylinder head cover
10. Rear cylinder camshaft
11. Front cylinder camshaft
12. Rear valve lifter case
13. Front valve lifter case
14. Push rod
15. Crankshaft
16. Camshaft sprocket cover
17. Generator shaft
18. Generator cover
19. Left crankcase
20. Oil filter cartridge bracket
21. Oil filter cartridge
22. Right crankcase
23. Oil cooler
2-32

EAS20410
LUBRICATION DIAGRAMS
10
A-A
B-B
D
A
1
8
E
E
C
D
7
5
D-D
11
E-E
2-33

1. Oil tank
2. Dipstick
3. Oil pipe 2
4. Oil delivery pipe 1
5. Oil filter cartridge
7. Oil pipe 3
8. Oil pipe 4
9. Oil pipe 5
10. Oil strainer (oil tank)
2-34
3
3
A
6
7
C
C
B
B-B
5
B
6
D-D
2-35
C-C

1.
2.
3.
4.
5.
6.
7.
Valve lifter
Push rod
Rocker arm shaft
Oil pipe 1
Crankshaft
Oil pipe (F mark)
Oil pipe (R mark)
2-36
A
2
3
4
A-A
2-37

1.
2.
3.
4.
Oil pipe 1
Oil pump
Oil strainer (crankcase)
Joint pipe
2-38
2-39

1.
2.
3.
4.
A.
Main axle
Drive axle
Oil strainer (crankcase)
Oil pump
To the oil filter cartridge
2-40
1
5
B
B-B
5
B
A
A
1
2-41

1.
2.
3.
4.
5.
A.
Oil pipe 5
Transfer gear oil pump
Oil strainer (transfer gear case)
Middle drive shaft
Oil strainer (oil tank)
From the oil pump
2-42
2-43

1. Transfer gear oil pump
2. Middle driven shaft
2-44
CABLE ROUTING
EAS20430
CABLE ROUTING
1
6
7
B-B
D-D
C-C
1
1
E
6
D
E
C
B
D B
F
1
6
7
6
F-F
F
D
E
11
10
2-45
CABLE ROUTING
1. Clutch hose
2. Right handlebar switch lead
3. Main switch
4. Left handlebar switch lead
5. Front brake hose
6. Throttle cable (decelerator cable)
7. Throttle cable (accelerator cable)
8. Horn 1 lead
9. Horn 1
10. Rear brake light switch
11. Rear brake light switch lead
A. Cross the left and right handlebar switch leads.
Either lead can be routed on top.
B. 70 mm (2.76 in)
C. 1030
D. Fasten the rear brake light switch lead with the
plastic locking tie. Face the end of the plastic
locking tie inward, and then cut off the excess end
of the tie.
E. Make sure that there is no slack in the rear brake
light switch lead in the area shown in the illustration.
F. Fasten the rear brake light switch lead with the
plastic locking tie. Face the end of the plastic
locking tie downward, and then cut off the excess
end of the tie.
2-46
CABLE ROUTING
2
A
B
F
C
F
G
D
6
G
8
E
E
9
A
1
B
B
B-B
D
8
6
10
1
2
F
3
G-G
F-F
D-D
G
E-E
2-47
CABLE ROUTING
1. Main switch lead
2. Right handlebar switch lead
3. Wire harness
4. Left handlebar switch lead
5. Air temperature sensor lead
6. Front left turn signal/position light lead
7. Headlight lead
8. Front right turn signal/position light lead
10. Main switch
A. Place the joint coupler behind the leads.
B. Place the sections of the handlebar switch leads
that are not covered by their protective sleeves in
the rear of the headlight housing.
C. Fasten the headlight leads, front turn
signal/position light leads, and accessory light lead
with the holders along the side of the headlight
housing.
D. Place the headlight leads, front turn signal/position
light leads, and accessory light lead near the base
of the holder.
E. 30 mm (1.18 in)
F. Secure the plastic band by inserting the projection
on the band into the hole in the headlight housing.
G. Face the end of the plastic band downward.
2-48
CABLE ROUTING
A-A
B-B
20 21
U
T
R
3
C-C
10
4
8
11
T
4
D-D
C D
A B
5
4
6 B C
A
D
F
D
C
B
12
13
14
19
18
H
I
H
G
O
17
16 15
24
22 23
V
14
14
14
G-G
H-H
AE
F-F
X
25 Y
AF
26
AD
27 Y
AH
J-J
Z AC AB
14
AG
28
2-49
AA
CABLE ROUTING
J. Fasten the wire harness and the cylinder-#2 left
and right spark plug leads with a plastic locking tie,
making sure to install the tie just past the end of the
protective tube of the wire harness. Face the end of
the plastic locking tie inward, and then cut off the
excess end of the tie.
K. To the throttle position sensor
L. To the fuel injector and engine temperature sensor
M. To the neutral switch
N. To the speed sensor
O. Fasten the stator coil lead with the plastic locking
ties. Face the end of each plastic locking tie
outward, and then cut off the excess end of the tie.
P. To the rear brake caliper
Q. Install the O2 sensor coupler completely onto the
O2 sensor bracket.
1. EXUP servo motor

2. Fuse box
3. Wire harness
4. Fuel outlet hose
5. Cylinder-#1 right spark plug cap
7. Cylinder-#2 intake air pressure sensor coupler
8. Fuel sender (fuel tank) coupler
9. Meter assembly coupler
10. Throttle cable
11. Front brake hose
14. Clutch pipe
15. Neutral switch lead
16. Stator coil lead
17. Speed sensor lead
18. O2 sensor lead
R. Outside of the frame

S. Position the buckle of the plastic locking tie to the
inside of the frame. Face the end of the plastic
locking tie upward, and then cut off the excess end
of the tie.
T. Inside of the frame
U. Position the buckle of the plastic locking tie to the
inside of the frame.
V. To the wire harness
W. To the cylinder-#2 right spark plug
X. Right side
Y. Position the sub-wire harness 3 coupler and the
sub-wire harness 4 coupler between the cylinder#2 right spark plug lead and the cylinder-#1 ISC
unit outlet hose.
Z. Face the ends of the hose clamp outward, angled
45 downward.
AA.Route the cylinder-#2 right spark plug lead under
the sub-wire harness 4.
AB.Face the ends of the hose clamp downward.
AC.Route the cylinder-#2 left spark plug lead under the
cylinder-#2 ISC unit outlet hose.
AD.Left side
AE.To the cylinder-#2 left spark plug
AF. Install the clutch pipe onto the clutch release
cylinder, making sure that the pipe contacts the
projection on the cylinder.
AG.To the O2 sensor
19. EXUP cable

20. Cylinder-#1 right spark plug lead
21. Cylinder-#1 left spark plug lead
22. ISC (idle speed control) unit inlet hose
23. Cylinder-#2 ISC (idle speed control) unit outlet
hose
hose
25. Sub-wire harness 3 coupler
26. Cylinder-#2 right spark plug lead
27. Sub-wire harness 4 coupler
A. Fasten the cylinder-#1 left and right spark plug
leads, fuel outlet hose, wire harness and the fuel
tank damper with the plastic locking tie. Install the
plastic locking tie in the rear slot of the fuel tank
damper.
B. Fasten the fuel outlet hose, wire harness, and fuel
tank damper with the plastic locking tie. Install the
plastic locking tie in the front slot of the fuel tank
damper and make sure that the end of the damper
is aligned with the edge of the flat section on the
outside of the frame.
C. Fasten the cylinder-#1 left and right ignition coil
leads, engine temperature sensor lead, and throttle
position sensor lead to the guide on the engine
bracket (right upper side) with the plastic locking tie.
Face the end of the plastic locking tie rearward, and
then cut off the excess end of the tie.
D. Fasten sub-wire harness 2 with the plastic locking
tie.
E. Align the positioning tape on the wire harness with
the top of the frame.
F. 015 mm (00.59 in)
G. Route the throttle cables behind the front brake
hose.
H. Make sure that the wire harness is not twisted
between the fuel tank and the headlight assembly.
I. Position the cylinder-#2 left and right spark plug
leads, sub-wire harness 2 coupler and sub-wire
harness 4 coupler on top of the guide.
AH.Align the cutout in the clutch pipe union bolt cap

with the projection on the clutch release cylinder.
2-50
CABLE ROUTING
C
A B 2 3 4
F
6 G
H
21
B
B
20
22
19
18 U
T
17
S
P
R 16 Q
15
26
27
O N 14 N M 13 12
28
29
30
31
11 K
10
24
32
25
AA
23
33
Z
24
A-A
AB
Z
AC
X
36
16
B-B
18
15
C
S
R
15
34
35
O
18
E-E
2-51
C-C
16
CABLE ROUTING
K. Fasten the stator coil lead and rectifier/regulator
lead with the plastic locking tie. Face the end of the
plastic locking tie outward, and then cut off the
L. Fasten the lean angle sensor lead, starter motor
lead, horn 1 lead, rear brake light switch lead, and
sidestand switch lead with the holder.
M. Route the starter motor lead, horn 1 lead, rear
brake light switch lead, and sidestand switch lead to
the inside of the frame boss.
N. Fasten the starter motor lead, horn 1 lead, rear
brake light switch lead, and sidestand switch lead
with the plastic locking tie. Face the end of the
plastic locking tie outward, and then cut off the
O. Fasten the starter motor lead, horn 1 lead, and rear
brake light switch lead with the plastic locking tie,
and then face the end of the tie outward. Be sure to
install the plastic locking tie behind the frame cross
member and to fasten the rear brake light switch
lead at the white tape.
P. Route the starter motor lead, horn 1 lead, and rear
brake light switch lead along the frame in the area
shown in the illustration, making sure not to cross
the leads.
Q. Align the positioning tape on the starter motor lead
with the engine mounting bolt (front lower side).
R. Pass the fuel tank breather/overflow hose through
the horn 1 bracket, making sure to position the end
of the hose as shown in the illustration.
S. Fasten the starter motor lead, horn 1 lead, and rear
brake light switch lead with the plastic locking tie,
and then face the end of the tie inward.
T. Fasten the horn 1 lead, rear brake light switch lead,
and starter motor lead with the plastic locking tie.
Face the end of the plastic locking tie inward, and
U. Route the horn lead 1 to the rear of the starter
motor lead.
V. Pass the throttle cables through the cable guides
as shown in the illustration.
W. Pass the plastic locking tie through the hole in the
battery box projection, and then fasten the wire
harness with the tie.
X. Fasten the stator coil lead at the white tape with the
plastic locking tie.
Y. Fasten the stator coil lead with the plastic locking
ties.
Z. Pass the plastic locking tie through the hole in the
battery box projection, and then fasten the wire
harness with the tie.
AA.Route the wire harness along the side of the fuse
box/starter relay bracket.
AB.For California only
AC.Route the horn lead 1 to the rearward of the
canister.
1. Clutch hose
2. Throttle cable (decelerator cable)
3. Throttle cable (accelerator cable)
4. Cylinder-#2 left spark plug cap
6. Sub-wire harness 1
7. Rectifier/regulator
8. Crankshaft position sensor lead
9. Stator coil lead
10. Rectifier/regulator lead
12. Horn 2 lead
13. Horn 2
14. Sidestand switch
15. Horn 1 lead
16. Rear brake light switch lead
17. Horn 1
18. Starter motor lead
19. Clutch pipe
20. Fuel tank breather/overflow hose
21. Rollover valve
22. Front brake hose
23. Headlight assembly
24. Front fork
25. Frame
26. Main fuse
27. Diode 1
28. Relay unit
29. Turn signal relay
30. Headlight relay
31. Starter relay
33. EXUP cable
35. Wire harness
36. Canister
A. Route the throttle cables to the inside of the clutch
hose.
B. Pass the cylinder-#2 left spark plug lead through
the guide.
C. 3040 mm (1.181.57 in)
D. Position the buckle of the plastic locking tie to the
inside of the frame.
E. Fasten the crankshaft position sensor lead, neutral
switch lead, and sidestand switch lead with the
holders.
F. Fasten the starter motor lead, speed sensor lead,
and wire harness with the holders.
G. Route sub-wire harness 1 to the inside of the
frame.
H. To the tail/brake light
I. Fasten the starter motor lead, horn 1 lead, rear
brake light switch lead, sidestand switch lead, and
crankshaft position sensor lead with the plastic
locking tie.
J. Make sure that there is no slack in the stator coil
lead and rectifier/regulator lead in the area shown
in the illustration.
2-52
CABLE ROUTING
16 17
K
15
A
8
18
A-A
B-B
14
E
13
B
3
J
12
D
E
G
E
D
H
15
22
23
21
5
6
11
24
7
25
10
19
N
18
16
20
D-D
E-E
17
O
8
W
28
X
U
5 P
27
26
2-53
CABLE ROUTING
L. Route the crankshaft position sensor lead,
sidestand switch lead, neutral switch lead, starter
motor lead and speed sensor lead under the fuel
outlet hose.
M. Inside of frame
N. Outside of frame
O. View with tray removed
P. Route the negative battery lead under the starter
motor lead and battery positive lead.
Q. Route the positive battery lead (main fuse to starter
relay) over the tray.
R. Route the negative battery lead towards the front of
the vehicle.
S. Route the positive battery lead (battery to starter
relay) under the tray.
T. View with tray installed
U. To the tail/brake light
V. View with ECU removed
W. Wrap the protective covering around the couplers
(crankshaft position sensor coupler, auxiliary DC
coupler, neutral switch coupler, sub-wire harness 1
coupler, speed sensor coupler, and sidestand
switch coupler) and the wire harness.
X. When installing the ECU, be sure not to pinch the
leads in the areas shown in the illustration with
oblique lines.
1. Meter assembly coupler

4. Wire harness
5. Negative battery lead
6. EXUP servo motor
7. Fuse box
9. Positive battery lead
14. Fuel sender (fuel tank) coupler
15. Neutral switch lead
16. Sidestand switch lead
17. Crankshaft position sensor lead
19. Fuel hose (fuel tank to fuel hose joint)
20. Fuel return hose (fuel return pipe to sub-fuel tank)
21. Air vent hose (fuel pump to fuel hose joint)
22. Fuel outlet hose
23. Frame
24. Oil tank
25. Sub-fuel tank
26. Battery
27. Main fuse
28. Fuel pump lead
A. Do not pinch the leads between the fuel tank
bracket and the frame when installing the bracket.
B. Pass the plastic locking ties through the holes in
the frame damper, and then fasten the wire harness
and damper with the ties. Face the end of each
plastic locking tie upward, and then cut off the
C. Align the white tape on the wire harness with the
frame cross member.
D. 20 mm (0.79 in)
E. Fasten the wire harness with the plastic locking tie.
Face the end of the plastic locking tie upward, and
F. Route the wire harness along the frame.
G. Fasten the wire harness with the plastic locking tie,
making sure to align the tie with the line on the
rubber damper. Face the end of the plastic locking
tie upward, and then cut off the excess end of the
tie.
H. Connect the ECU couplers, and then fasten the
ECU with the band.
I. Fasten the fuel return hose (fuel return pipe to subfuel tank) with the plastic locking tie. Face the end
of the plastic locking tie inward, and then cut off the
J. Fasten the fuel tank damper with the plastic locking
tie. Install the plastic locking tie in the middle slot of
the fuel tank damper.
K. Fasten the air filter case damper with the plastic
locking tie so that the rubber part of the damper
contacts the frame. Be sure to pass the plastic
locking tie between the air filter case damper and
the frame.
2-54
CABLE ROUTING
D
4
5
6
7
A
17
23
C B
18
19
15
16
22
12
11
10
13
E
14
21
20
F
I
H
R
S
Q
24
L
P
25
5
O
5
J
11
E
U
M
4
21
V
11
26
8
24
27
C
C
C-C
B
28
2-55
CABLE ROUTING
Q. Install the air vent hose (fuel hose joint to fuel tank)
with its white paint mark facing downward.
R. For California only
S. To the fuel tank
T. To the intake manifold assembly
U. Fasten the canister purge hose and fuel tank
breather/overflow hose with the holder, making sure
to align the paint mark on the breather/overflow
hose with the holder.
V. Fasten the canister purge hose and throttle cable
guide with the holder.
1. Fuel tank breather hose

2. Fuel sender (fuel tank)
3. Fuel tank
4. Fuel hose (fuel tank to fuel hose joint)
5. Fuel return hose (fuel return pipe to sub-fuel tank)
6. Air vent hose (fuel hose joint to fuel tank)
7. Fuel hose joint
8. Fuel outlet hose
9. Fuel pump
10. Sub-fuel tank
11. Fuel hose (fuel hose joint to fuel pump)
12. Fuel return pipe
13. Fuel return hose (pressure regulator to fuel return
pipe)
15. Rollover valve 1
16. Rollover valve 2
18. Rollover valve hose 1
21. Fuel tank breather/overflow hose
24. Air vent hose (fuel pump to fuel hose joint)
25. Fuel pump coupler
26. Canister purge hose (for California only)
27. Canister (for California only)
28. Canister breather hose (for California only)
A. Align the blue paint mark on the fuel hose (fuel
hose joint to fuel tank) with the round indentation on
the bend in the fuel hose joint.
B. Face the fastener of the clamp downward, making
sure that the projections on the clamp are
positioned as shown in the illustration.
C. Align the white paint mark on the end of the fuel
return hose (fuel return pipe to sub-fuel tank) with
the white paint mark on the fuel return pipe.
D. Align the paint marks on the hoses with the hose
joint as shown in the illustration.
E. Fasten the fuel tank breather/overflow hose to the
throttle cable guide with the holder.
F. Align the paint mark on the hose with the hose joint
as shown in the illustration.
G. Fasten the fuel tank breather/overflow hose and
starter motor lead with the holder.
H. To the fuel injector
I. Align the yellow paint mark on the air vent hose
(fuel hose joint to fuel tank) with the round
indentation on the bend in the fuel hose joint.
J. Face the fastener of the clamp to the left.
K. Face the ends of the hose clamp forward.
L. Install the air vent hose (fuel pump to fuel hose
joint) with its white paint mark facing upward.
M. Face the ends of the hose clamp upward.
N. Face the fastener of the clamp upward, making
sure that the projections on the clamp are
positioned as shown in the illustration.
O. Install the fuel hose (fuel tank to fuel hose joint)
with its white paint mark facing downward.
P. To the pressure regulator
2-56
CABLE ROUTING
A
5
10
E
D
1
11
12
17
13
B
H
G
14
16
13
15
11
18
I
C
13
13
11
C-C
11
11
C
B
19
4
5
20
K
21
22
2-57
CABLE ROUTING
1.
2.
3.
4.
Cylinder-#1 intake air pressure sensor

Cylinder-#1 intake air pressure sensor hose
Air filter case breather hose 1
Fuel hose (intake manifold assembly to pressure
regulator)
6. Air filter case breather hose 2
7. Canister purge hose (for California only)
8. ISC (idle speed control) unit inlet hose
9. Canister (for California only)
10. Fuel tank breather/overflow hose (for California
only)
hose
hose
15. Cylinder-#1 intake air pressure sensor hose
16. Fuel outlet hose
17. Cylinder head breather hose
18. Hose joint cover
20. Cylinder-#1 injector coupler
21. Engine temperature sensor coupler
A. Face the ends of the hose clamp to the left, angled
45 rearward.
B. Install the cylinder-#1 intake air pressure sensor
hose onto the throttle body pipe up to the bend in
the pipe, making sure to face the white paint mark
on the hose upward. Face the ends of the hose
clamp forward.
C. Fasten the canister purge hose and the air filter
case breather hose 2 with the hose clamp, making
sure to face the ends of the clamp upward (for
California only).
D. Face the ends of the hose clamp to the left.
E. Fasten the canister purge hose and fuel tank
breather/overflow hose with the holder 70 mm (2.76
in) from the hose joints on the canister (for
California only).
F. Install the cylinder-#2 intake air pressure sensor
hose onto the throttle body pipe up to the bend in
the pipe, making sure to face the white paint mark
on the hose upward. Face the ends of the hose
clamp rearward.
G. Install the canister purge hose onto the throttle
body pipe up to the bend in the pipe, making sure to
face the white paint mark on the hose upward (for
California only).
H. Face the ends of the hose clamp rearward, angled
to the left.
I. Align the white paint marks.
J. Align the yellow paint marks.
K. Route the canister purge hose over the air filter
case joint clamp screw.
2-58
CABLE ROUTING
5
16
E
15
9 10 B 11 B
10
C
14
8
7
13
12
17
9
18
10
19
I
B
8
J
8
G
9
10
2-59
CABLE ROUTING
1.
2.
3.
4.
5.
6.
7.
8.
9.

ISC (idle speed control) unit coupler
Rollover valve 1
Rollover valve 2
ISC (idle speed control) unit inlet hose
Cylinder-#1 ISC (idle speed control) unit outlet
hose
hose
11. Hose joint
12. Air filter case breather hose 2
14. Throttle body assembly
15. Cylinder-#1 intake air pressure sensor hose
16. Cylinder head breather hose
A. Face the ends of the hose clamp inward.
B. Face the ends of the hose clamps outward.
C. Install the cylinder-#2 ISC (idle speed control) unit
outlet hose (hose joint to intake manifold assembly)
completely onto the intake manifold, making sure to
face the green paint mark on the hose to the left.
Face the ends of the hose clamp outward, angled
45 forward.
D. Install the cylinder-#1 ISC (idle speed control) unit
outlet hose (hose joint to intake manifold assembly)
completely onto the intake manifold, making sure to
face the blue paint mark on the hose to the left.
E. Face the ends of the hose clamp upward.
F. Position the sub-wire harness 4 coupler on top of
the guide.
G. To the wire harness
H. Install the cylinder-#1 ISC (idle speed control) unit
outlet hose onto the ISC unit pipe, making sure to
align the blue paint mark on the hose with the blue
paint mark on the pipe.
I. Install the ISC (idle speed control) unit inlet hose
onto the ISC unit pipe, making sure to align the
white paint mark on the hose with the white paint
mark on the pipe.
J. Install the cylinder-#2 ISC (idle speed control) unit
outlet hose onto the ISC unit pipe, making sure to
align the green paint mark on the hose with the
green paint mark on the pipe.
2-60
PERIODIC CHECKS AND ADJUSTMENTS

PERIODIC MAINTENANCE............................................................................ 3-1
INTRODUCTION....................................................................................... 3-1
PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL
SYSTEM................................................................................................... 3-1
GENERAL MAINTENANCE AND LUBRICATION CHART....................... 3-1
ENGINE ........................................................................................................... 3-4
ADJUSTING THE VALVE CLEARANCE .................................................. 3-4
SYNCHRONIZING THE THROTTLE BODIES ......................................... 3-7
ADJUSTING THE THROTTLE CABLE FREE PLAY ................................ 3-8
CHECKING THE SPARK PLUGS............................................................. 3-9
CHECKING THE IGNITION TIMING....................................................... 3-10
CHECKING THE ENGINE OIL LEVEL ................................................... 3-11
CHANGING THE ENGINE OIL ............................................................... 3-11
CHECKING THE TRANSFER GEAR OIL LEVEL................................... 3-13
CHANGING THE TRANSFER GEAR OIL .............................................. 3-14
CHECKING THE CLUTCH FLUID LEVEL .............................................. 3-14
BLEEDING THE HYDRAULIC CLUTCH SYSTEM................................. 3-15
REPLACING THE AIR FILTER ELEMENT ............................................. 3-16
CHECKING THE THROTTLE BODY JOINTS ........................................ 3-16
CHECKING THE FUEL LINE .................................................................. 3-16
CHECKING THE CYLINDER HEAD BREATHER HOSE ....................... 3-17
CHECKING THE OIL TANK BREATHER HOSE .................................... 3-17
CHECKING THE EXHAUST SYSTEM ................................................... 3-18
CHECKING THE CANISTER (for California only)................................... 3-18
ADJUSTING THE EXUP CABLES.......................................................... 3-18
CHASSIS....................................................................................................... 3-20
ADJUSTING THE REAR DISC BRAKE .................................................. 3-20
CHECKING THE BRAKE FLUID LEVEL ................................................ 3-20
CHECKING THE FRONT BRAKE PADS................................................ 3-21
CHECKING THE REAR BRAKE PADS .................................................. 3-21
CHECKING THE FRONT BRAKE HOSES ............................................. 3-21
CHECKING THE REAR BRAKE HOSES ............................................... 3-22
ADJUSTING THE REAR BRAKE LIGHT SWITCH................................. 3-22
BLEEDING THE HYDRAULIC BRAKE SYSTEM ................................... 3-22
ADJUSTING THE SHIFT PEDAL............................................................ 3-23
ADJUSTING THE DRIVE BELT SLACK ................................................. 3-24
CHECKING AND ADJUSTING THE STEERING HEAD......................... 3-25
CHECKING THE FRONT FORK............................................................. 3-26
ADJUSTING THE REAR SHOCK ABSORBER ASSEMBLY.................. 3-27
CHECKING THE TIRES ......................................................................... 3-27
CHECKING THE WHEELS ..................................................................... 3-29
CHECKING AND LUBRICATING THE CABLES .................................... 3-29
LUBRICATING THE LEVERS................................................................. 3-30
LUBRICATING THE PEDAL ................................................................... 3-30
LUBRICATING THE SIDESTAND .......................................................... 3-30
LUBRICATING THE REAR SUSPENSION ............................................ 3-30
ELECTRICAL SYSTEM ................................................................................ 3-31

CHECKING AND CHARGING THE BATTERY....................................... 3-31
CHECKING THE FUSES ........................................................................ 3-31
REPLACING THE HEADLIGHT BULBS ................................................. 3-31
ADJUSTING THE HEADLIGHT BEAMS................................................. 3-32
PERIODIC MAINTENANCE
EAS20450
EAS20460
INTRODUCTION
This chapter includes all information necessary to perform recommended checks and adjustments. If
followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work. This information applies to vehicles already
in service as well as to new vehicles that are being prepared for sale. All service technicians should be
familiar with this entire chapter.
EAU17600
PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL SYSTEM

INITIAL
No.
ITEM
1 * Fuel line
2 * Spark plugs
3 * Valve clearance
4 * Crankcase
breather system
5 * Fuel injection
6 * Exhaust system
Evaporative emission control sys7 * tem (For
California only)
ROUTINE
ODOMETER READINGS
8000 mi
12000 mi 16000 mi 20000 mi
600 mi
4000 mi
(13000
(19000
(25000
(31000
(1000 km) (7000 km)
km)
km)
km)
km)
or
or
or
or
or
or
1 month 6 months
12 months 18 months 24 months 30 months
Check fuel hoses for cracks or

damage.
Replace if necessary.
Check condition.
Adjust gap and clean.
Replace every 8000 mi
(13000 km) or 12 months.
Check and adjust valve clearance when engine is cold.
Adjust if necessary.
Check breather hose for
cracks or damage.
Adjust synchronization.
Check for leakage.
Tighten if necessary.
Replace gasket(s) if necessary.
Replace.
Replace.
Every 16000 mi (25000 km)
Check control system for

damage.
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the
service.
EAU32183
GENERAL MAINTENANCE AND LUBRICATION CHART

INITIAL
No.
ITEM
1 * Air filter element

2 * Clutch
3 * Front brake
4 * Rear brake
5 * Brake hoses
ROUTINE
Check condition and damage.

Check operation and fluid
leakage.
Correct if necessary.
Check operation, fluid level,
and for fluid leakage.
Replace brake pads if necessary.
Check operation, fluid level,
and for fluid leakage.
Replace brake pads if necessary.
Check for cracks or damage.
Replace.
ODOMETER READINGS
600 mi
4000 mi
(1000 km) (7000 km)
or
or
1 month 6 months
8000 mi
12000 mi 16000 mi 20000 mi
(13000
(19000
(25000
(31000
km)
km)
km)
km)
or
or
or
or
Every 4 years
3-1
INITIAL
No.
ITEM
ROUTINE
ODOMETER READINGS
8000 mi
12000 mi 16000 mi 20000 mi
600 mi
4000 mi
(13000
(19000
(25000
(31000
(1000 km) (7000 km)
km)
km)
km)
km)
or
or
or
or
or
or
1 month 6 months
Check runout and for damage.

Check tread depth and for
damage.
Check air pressure.
Check bearings for smooth
operation.
Check bearing assemblies for
looseness.
Check belt tension.
Adjust if necessary.
Check bearing assemblies for
looseness.
Moderately repack with lithium-soap-based grease every
16000 mi (25000 km) or 24
months.
Check all chassis fitting and
fasteners.
Apply lithium-soap-based
grease (all-purpose grease)
lightly.
lightly.
Check operation.
lightly.
Check operation and replace
if necessary.
Check operation and for oil
leakage.
Check operation and for oil
leakage.
grease lightly.
Change (warm engine before
draining).
Engine oil filter

21 * cartridge
Replace.
22 * Transfer case oil
Check for leakage.

Change at initial 600 mi (1000
km) or 1 month, and thereafter every 16000 mi (25000
km) or 24 months.
Change.
Change.
6 * Wheels
7 * Tires
8 * Wheel bearings
9 *
Swingarm pivot
bearings
10 * Drive belt
11 * Steering bearings
12 * Chassis fasteners
13
Brake and clutch

lever pivot shafts
14
Brake and shift

pedal pivot shafts
15
Sidestand pivot
16 * Sidestand switch
17 * Front fork
18 *
Shock absorber
assembly
19 * Rear suspension
link pivots
20
23 *
Engine oil
Front and rear

brake switches
24 * Control cables
Throttle grip
25 * housing and cable
26 *
Lights, signals
and switches
Check operation.
Apply Yamaha chain and cable lube or engine oil SAE
10W-30 thoroughly.
Check operation and free
play.
Adjust the throttle cable free
play if necessary.
Lubricate the throttle grip
housing and cable.
Check operation.
Adjust headlight beam.
Every 2500 mi (4000 km)
Repack.
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the
service.
3-2
NOTE:
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi
(13000 km) or 12 months.
EAU38440
NOTE:
Air filter
This models air filter is equipped with a disposable oil-coated paper element, which must not be
cleaned with compressed air to avoid damaging it.
The air filter element needs to be replaced more frequently when riding in unusually wet or dusty
areas.
Hydraulic brake and clutch systems
After disassembling the brake or clutch master cylinders, caliper cylinders or clutch release cylinder,
always change the fluid. Regularly check the brake and clutch fluid levels and fill the reservoirs as
required.
Replace the oil seals on the inner parts of the brake or clutch master cylinders, caliper cylinders and
clutch release cylinder every two years.
Replace the brake and clutch hoses every four years or if cracked or damaged.
3-3
ENGINE
Fuel tank
Refer to FUEL TANK on page 6-1.
Air filter case
Refer to GENERAL CHASSIS on page 4-1.
Muffler
Exhaust pipes
Refer to ENGINE REMOVAL on page 5-1.
2. Disconnect:
Spark plug caps
3. Remove:
Spark plugs
4. Remove:
Shift pedal assembly 1
EAS20470
ENGINE
EAS20530
ADJUSTING THE VALVE CLEARANCE

The following procedure applies to all of the
valves.
NOTE:
The valve clearance is automatically adjusted

by the hydraulic valve lifter. However, there are
times when the valve clearance needs to be
adjusted manually. If this is the case, adjust the
clearance of the two maladjusted or worn
valves using the adjusting screw on the rocker
arm.
If clearance is on the slip side 1, loosen the
adjusting screw and bring the valve clearance
a within specification. Check if the valve
clearance b on the adjusting screw 2 side is
within specification.
5. Remove:
Damper cover 1
Damper 2
Timing mark accessing screw 3
Crankshaft end screw 4
If clearance is on the adjusting screw 2 side,
tighten the adjusting screw and bring the valve
clearance b within specification.
3 2
1
6. Remove:
Camshaft sprocket cover 1
Valve clearance adjustment should be made

on a cold engine, at room temperature.
When the valve clearance is to be measured or
adjusted, the piston must be at top dead center
(TDC) on the compression stroke.
1. Remove:
Rider seat
Rider seat bracket assembly
7. Remove:
Wire harness guide bolt 1
3-4
ENGINE
2
3
8. Remove:
Fuel tank damper 1
Cylinder head breather hose 2
9. Disconnect:
Oil tank breather hose 3
Fuel outlet hose 4
11.Measure:
Valve clearance
Out of specification Adjust.
Valve clearance (cold)
Intake
0.000.04 mm (0.00000.0016 in)
Exhaust
0.000.04 mm (0.00000.0016 in)
1
3
Piston #1 TDC (rear cylinder)

a. Turn the crankshaft counterclockwise.
10.Remove:
Front cylinder head cover 1
Rear cylinder head cover 2
NOTE:
Due to the small clearance between the frame

and the rear cylinder head cover, the three bolts
3 cannot be removed when the cover is in
place. Loosen the bolts, and then remove the
cylinder head cover from the right side of the vehicle, making sure that the bolts do not scratch
the rocker arms or other engine parts.
b. When piston #1 is at TDC on the compression stroke, align the TDC mark a on the
crankshaft position sensor rotor with the
pointer b on the clutch cover.
c. Check the camshaft drive gear mark c position and camshaft driven gear mark d position as shown.
If the marks are not aligned, turn the crankshaft counterclockwise 360 degrees and recheck step (b).
3-5
ENGINE
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-9
12.Adjust:
Valve clearance
a. Loosen the locknut 1.
d. Measure the valve clearance with a thickness

gauge.
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-9
Piston #2 TDC (front cylinder)

a. Turn the crankshaft counterclockwise from
the piston #1 TDC by 408 degrees.
b. When piston #2 is at TDC on the compression stroke, align the TDC mark e on the
b. Insert a thickness gauge 2 between the end

of the adjusting screw and the valve tip.
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-9
c. Turn the adjusting screw 3 in direction a or
b with the tappet adjusting tool 4 until the
specified valve clearance is obtained.

90890-04133
Valve adjustment wrench 3 mm &
4 mm
YM-08035-A
Adjusting
screw side
d. Measure the valve clearance with a thickness

gauge.
3-6
Slip side
Direction a
Valve clearance is increased.
Valve clearance is decreased.
Direction b
Valve clearance is decreased.
Valve clearance is increased.
ENGINE

Fuel tank
3. Remove:
Cylinder-#1 intake air pressure sensor bracket 1
Cylinder-#2 intake air pressure sensor bracket 2
3 2
d. Hold the adjusting screw to prevent it from

moving and tighten the locknut to specification.
1
T.
R.
Locknut (rocker arm adjusting

screw)
20 Nm (2.0 mkg, 14 ftlb)
90890-04133
Valve adjustment wrench 3 mm &
4 mm
YM-08035-A
4. Disconnect:
1
2
e. Measure the valve clearance again.

f. If the valve clearance is still out of specification, repeat all of the valve clearance adjustment steps until the specified clearance is
obtained.
13.Install:
All removed parts
Refer to CAMSHAFTS on page 5-14.
NOTE:
5. Install:
Hose 1 (Parts No.: 5JW-24311-00)
3-way joint 2 (Parts No.: 90413-05014)
Vacuum gauge hose for #1 3
Vacuum gauge hose for #2 4
5
6
Vacuum gauge
Tachometer
For installation, reverse the removal procedure.

EAS20570
SYNCHRONIZING THE THROTTLE BODIES

NOTE:
Prior to synchronizing the throttle bodies, the

valve clearance and the engine idling speed
should be properly adjusted and the ignition timing should be checked.
1. Stand the vehicle on a level surface.
NOTE:
Vacuum gauge
90890-03094
Carburetor synchronizer
YU-44456
Place the vehicle on a suitable stand.

2. Remove:
Rider seat
3-7
ENGINE
NOTE:
The difference in vacuum pressure between two

throttle bodies should not exceed 1.33 kPa (10
mmHg).
4
6
2
1
8. Stop the engine and remove the measuring

equipment.
9. Adjust:
Refer to ADJUSTING THE THROTTLE CABLE FREE PLAY on page 3-8.
5
3
6. Install:
Fuel tank
7. Adjust:
Throttle body synchronization

4.06.0 mm (0.160.24 in)
10.Install:
Fuel tank
Rider seat
a. Start the engine and let it warm up for several

minutes, and then let it run at specified engine idling speed.
Engine idling speed
850950 r/min
b. With throttle body #1 as standard, adjust
throttle body #2 using the air screw 1 (for
throttle body #2).
EAS20630
ADJUSTING THE THROTTLE CABLE FREE

PLAY
NOTE:
Prior to adjusting the throttle cable free play, the

engine idling speed and throttle body synchronization should be adjusted properly.
1. Check:
Throttle cable free play a
NOTE:
After each step, rev the engine two or three

times, each time for less than a second, and
check the synchronization again.
If the air screw was removed, turn the screw
3/4 turn in and be sure to synchronize the throttle body.
ECA14900
CAUTION:
Do not use the throttle valve adjusting

screws to adjust the throttle body synchronization.

4.06.0 mm (0.160.24 in)
2. Adjust:
Intake vacuum
31.335.3 kPa (9.310.4 inHg)
(235265 mmHg)
3-8
ENGINE
4. Check:
Spark plug type
Incorrect Change.

b. Turn the adjusting nut 2 in direction a or b
until the specified throttle cable free play is
obtained.
Manufacturer/model
NGK/DPR8EA-9
Manufacturer/model
DENSO/X24EPR-U9
Direction a
Throttle cable free play is increased.
Direction b
Throttle cable free play is decreased.
5. Check:
Electrode 1
Damage/wear Replace the spark plug.
Insulator 2
Abnormal color Replace the spark plug.
Normal color is medium-to-light tan.
6. Clean:
Spark plug
(with a spark plug cleaner or wire brush)
7. Measure:
Spark plug gap a
(with a wire thickness gauge)
Out of specification Regap.
c. Tighten the locknut 1.
EWA12910
Spark plug gap

0.80.9 mm (0.0310.035 in)
WARNING
After adjusting the throttle cable free play,

start the engine and turn the handlebar to the
right and to the left to ensure that this does
not cause the engine idling speed to change.
EAS20680
CHECKING THE SPARK PLUGS

spark plugs.
1. Remove:
Rider seat
Fuel tank
Air filter case
2. Disconnect:
Spark plug cap
3. Remove:
Spark plug
8. Install:
Spark plug
T.
R.
Spark plug
18 Nm (1.8 mkg, 13 ftlb)
NOTE:
Before installing the spark plug, clean the spark

plug and gasket surface.
9. Connect:
Spark plug cap
ECA13320
CAUTION:
Before removing the spark plugs, blow away

any dirt accumulated in the spark plug wells
with compressed air to prevent it from falling
into the cylinders.
3-9
ENGINE
10.Install:
Air filter case
Fuel tank
Rider seat
EAS20700
CHECKING THE IGNITION TIMING
5. Check:
Ignition timing
NOTE:
Prior to checking the ignition timing, check the

wiring connections of the entire ignition system.
Make sure all connections are tight and free of
corrosion.
a. Start the engine, warm it up for several minutes, and then let it run at the specified engine idling speed.

2. Remove:
Engine idling speed

850950 r/min
b. Check that pointer a on the clutch cover is
within the firing range b on the crankshaft
position sensor rotor.
Incorrect firing range Check the ignition
system.
3. Remove:
Damper cover 1
Damper 2
Timing mark accessing screw 3
NOTE:
The ignition timing is not adjustable.
6. Install:
Timing mark accessing screw
Damper
Damper cover
3 2
1
T.
4. Connect:
Timing light 1
Tachometer
R.
Damper cover bolt

10 Nm (1.0 mkg, 7.2 ftlb)
7. Install:
T.
Timing light
90890-03141
Inductive clamp timing light
YU-03141
R.
3-10
Shift pedal bolt

18 Nm (1.8 mkg, 13 ftlb)
ENGINE
NOTE:
Type
YAMALUBE 4 (20W40) or
SAE20W40
Recommended engine oil grade
API service SE, SF, SG type or
higher
Align the mark a on the shift pedal shaft with

the slot in the shift pedal.
1
0
10
30
50
70
90
110 130 F
YAMALUBE 4 (20W40)
or SAE 20W40
EAS20750
CHECKING THE ENGINE OIL LEVEL

20 10
10
20
30
40 50 C
ECA13380
NOTE:
CAUTION:

Make sure the vehicle is upright.
2. Start the engine, warm it up for approximately
15 minutes until the oil temperature rises to
60 C (140 F), and then turn it off.
3. Remove:
Rider seat
4. Remove:
Dipstick 1
5. Check:
Engine oil level
The engine oil level should be between the
minimum level mark a and maximum level
mark b.
Below the minimum level mark Add the
recommended engine oil to the proper level.
Engine oil also lubricates the clutch and the

wrong oil types or additives could cause
clutch slippage. Therefore, do not add any
chemical additives.
Do not allow foreign materials to enter the
crankcase.
NOTE:
API Service SE, SF and SG type or equivalent (e.g., SF-SE, SF-SE-CC, SF-SE-SD)
6. Start the engine, warm it up for several minutes, and then turn it off.
7. Check the engine oil level again.
NOTE:
Before checking the engine oil level, wait a few

minutes until the oil has settled.
8. Install:
Dipstick
9. Install:
Rider seat
NOTE:
Before checking the engine oil level, wait a few

minutes until the oil has settled.
Do not screw the dipstick in when inspecting
the oil level.
EAS20780
CHANGING THE ENGINE OIL

1. Start the engine, warm it up for several minutes, and then turn it off.
2. Place a container under the engine oil drain
bolts.
3. Remove:
Engine oil filler cap 1
b
1
3-11
ENGINE
1
4. Remove:
Engine oil drain bolt (oil tank) 1
(along with the gasket)
b. Lubricate the O-ring 3 of the new oil filter

cartridge with a thin coat of engine oil.
ECA13390
CAUTION:
Make sure the O-ring 3 is positioned correctly in the groove of the oil filter cartridge.
5. Remove:
Engine oil drain bolts (crankcase) 1
(along with the gaskets)
c. Tighten the new oil filter cartridge to specification with an oil filter wrench.
T.
R.

17 Nm (1.7 mkg, 12 ftlb)
8. Check:
Engine oil drain bolt gaskets
Damage Replace.
9. Install:
T.
6. Drain:
Engine oil
(completely from the oil tank and crankcase)
7. If the oil filter cartridge is also to be replaced,
perform the following procedure.
R.
a. Remove the oil filter cartridge 1 with an oil

filter wrench 2.

43 Nm (4.3 mkg, 31 ftlb)
10.Install:
Engine oil drain bolts (crankcase)
(along with the gaskets)
Oil filter wrench

90890-01426
YU-38411
T.
R.
Engine oil drain bolt (crankcase)

43 Nm (4.3 mkg, 31 ftlb)
11.Fill:
Oil tank
(with the specified amount of the recommended engine oil)
3-12
ENGINE
Engine oil quantity
Total amount
5.20 L (5.50 US qt) (4.58 Imp.qt)
Without oil filter cartridge replacement
4.10 L (4.33 US qt) (3.61 Imp.qt)
With oil filter cartridge replacement
4.90 L (5.18 US qt) (4.31 Imp.qt)
b. Start the engine and keep it idling until engine

oil starts to seep from the oil gallery bolts. If
no engine oil comes out after one minute, turn
the engine off so that it will not seize.
c. Check the engine oil passages, the oil filter
cartridge and the oil pump for damage or
leakage. Refer to OIL PUMP on page 5-95.
d. Start the engine after solving the problem(s)
and check the engine oil pressure again.
e. Tighten the oil gallery bolts to specification.
NOTE:
Pour the engine oil in two stages. First, pour in

2.5 L of oil, then start the engine and rev it 3 to 5
times. Stop the engine, and then pour in the remainder of the specified amount.
EC1D71008
CAUTION:
When starting the engine make sure the dipstick is securely fitted into the oil tank.
R.
Engine oil quantity

Total amount
5.20 L (5.50 US qt) (4.58 Imp.qt)
Engine
3.2 L (3.38 US qt) (2.82 Imp.qt)
Oil tank
2.0 L (2.11 US qt) (1.76 Imp.qt)
T.
12.Fill: (when engine is disassembled)

Crankcase and oil tank
(with the specified amount of the recommended engine oil)
Oil gallery bolt

10 Nm (1.0 mkg, 7.2 ftlb)
EAS20840
CHECKING THE TRANSFER GEAR OIL

LEVEL
NOTE:

13.Install:
Engine oil filler cap
14.Start the engine, warm it up for several minutes, and then turn it off.
15.Check:
Engine
(for engine oil leaks)
16.Check:
Engine oil level
Refer to CHECKING THE ENGINE OIL
LEVEL on page 3-11.
17.Check:
Engine oil pressure
2. Remove:
Transfer gear oil check bolt 1
1
3. Check:
Transfer gear oil level
The transfer gear oil level should be up to the
brim 1 of the hole.
Below the brim Add the recommended
transfer gear oil to the proper level.
a. Slightly loosen the oil gallery bolts 1.
3-13
ENGINE
T.
R.

18 Nm (1.8 mkg, 13 ftlb)
7. Fill:
Transfer gear case
(with the specified amount of the recommended transfer gear oil)
Quantity
0.55 L (0.58 US qt) (0.48 Imp.qt)
Quantity (disassembled)
0.60 L (0.63 US qt) (0.53 Imp.qt)
Type
SAE80 API GL-4 Hypoid gear oil
EC1D71024
CAUTION:
Do not allow foreign materials to enter the

transfer gear case.
4. Install:
T.
R.

8 Nm (0.8 mkg, 5.8 ftlb)
8. Install:
Straight plug
9. Check:
Transfer gear oil level
Refer to CHECKING THE TRANSFER
GEAR OIL LEVEL on page 3-13.
10.Install:
Exhaust pipes
Muffler
EAS20850
CHANGING THE TRANSFER GEAR OIL

1. Remove:
Muffler
Exhaust pipes
2. Place a container under the transfer gear oil
drain bolt.
3. Remove:
Straight plug 1
Transfer gear oil drain bolt 2
EAS20890
CHECKING THE CLUTCH FLUID LEVEL

NOTE:
2. Check:
Clutch fluid level
Below the minimum level mark a Add the
recommended clutch fluid to the proper level.
1
Recommended clutch fluid
Brake fluid DOT 4
4. Drain:
Transfer gear oil
(completely from the transfer gear case)
5. Check:
Transfer gear oil drain bolt gasket
Damage Replace.
6. Install:
3-14
ENGINE
precaution could allow air to enter the hydraulic
clutch system, considerably lengthening the
bleeding procedure.
If bleeding is difficult, it may be necessary to let
the clutch fluid settle for a few hours. Repeat
the bleeding procedure when the tiny bubbles
in the hose have disappeared.
1. Bleed:
Hydraulic clutch system
EWA13370
a. Add the recommended clutch fluid to the

proper level.
b. Install the clutch master cylinder reservoir diaphragm.
c. Connect a clear plastic hose 1 tightly to the
bleed screw 2.
WARNING
Use only the designated clutch fluid. Other

clutch fluids may cause the rubber seals to
deteriorate, causing leakage and poor
clutch performance.
Refill with the same type of clutch fluid that
is already in the system. Mixing clutch fluids may result in a harmful chemical reaction, leading to poor clutch performance.
When refilling, be careful that water does
not enter the clutch fluid reservoir. Water
will significantly lower the boiling point of
the clutch fluid and could cause vapor lock.
1
2
ECA13420
CAUTION:
Clutch fluid may damage painted surfaces or

plastic parts. Therefore, always clean up any
spilt clutch fluid immediately.
NOTE:
In order to ensure a correct reading of the clutch

fluid level, make sure the top of the reservoir is
horizontal.
EAS20900
BLEEDING THE HYDRAULIC CLUTCH

SYSTEM
EWA13000
WARNING
R.
NOTE:
T.
Bleed the hydraulic clutch system whenever:

the system was disassembled,
a clutch hose was loosened or removed,
the clutch fluid level is very low,
clutch operation is faulty.
d. Place the other end of the hose into a container.

e. Slowly squeeze the clutch lever several
times.
f. Fully squeeze the clutch lever without releasing it.
g. Loosen the bleed screw. This will release the
tension and cause the clutch lever to contact
the handlebar grip.
h. Tighten the bleed screw and then release the
clutch lever.
i. Repeat steps (e) to (h) until all of the air bubbles have disappeared from the clutch fluid in
the plastic hose.
j. Tighten the bleed screw to specification.
Bleed screw (clutch release cylinder)
6 Nm (0.6 mkg, 4.3 ftlb)
k. Add the recommended clutch fluid to the

proper level.
Refer to CHECKING THE CLUTCH FLUID
LEVEL on page 3-14.
Be careful not to spill any clutch fluid or allow

the clutch master cylinder reservoir to overflow.
When bleeding the hydraulic clutch system,
make sure there is always enough clutch fluid
before applying the clutch lever. Ignoring this
3-15
ENGINE
air filter element will also affect the throttle
body synchronization, leading to poor engine performance and possible overheating.
EWA13010
WARNING
After bleeding the hydraulic clutch system,

check the clutch operation.
NOTE:
When installing the air filter element into the air

filter case, make sure that the sealing surfaces
are aligned to prevent any air leaks.
EAS20960
REPLACING THE AIR FILTER ELEMENT

1. Remove:
Rider seat
2. Remove:
Fuel tank
3. Remove:
Air filter case cover 1
7. Install:
Fuel tank
Rider seat
EAS21010
CHECKING THE THROTTLE BODY JOINTS

throttle body joints and intake manifolds.
1. Remove:
Rider seat
Fuel tank
Air filter case
2. Check:
Throttle body joints 1
Cracks/damage Replace.
4. Remove:
Air filter element 1
5. Check:
Air filter element
Damage Replace.
3. Install:
Air filter case
Fuel tank
Rider seat
NOTE:
The air filter needs more frequent service if you

are riding in unusually wet or dusty areas.
6. Install:
Air filter case cover
EC1D71002
CAUTION:
EAS21030
CHECKING THE FUEL LINE

The following procedure applies to all of the fuel,
air vent and breather hoses.
1. Remove:
Rider seat
Never operate the engine without the air filter

element installed. Unfiltered air will cause
rapid wear of engine parts and may damage
the engine. Operating the engine without the
3-16
ENGINE
2. Check:
Cylinder head breather hose 1

Fuel tank
2. Check:
Fuel hoses 1
Air vent hose 2
Breather hose 3
ECA14920
CAUTION:
Make sure the cylinder head breather hose is

routed correctly.
ECA14940
CAUTION:
Make sure the fuel tank breather hose is routed correctly.
1
2
3. Install:
Air filter case
Fuel tank
Rider seat
EAS21060
CHECKING THE OIL TANK BREATHER

HOSE
1. Remove:
Right side cover
2. Check:
Oil tank breather hose 1
3. Install:
Fuel tank
Rider seat
ECA14930
CAUTION:
Make sure the oil tank breather hose is routed correctly.
EAS21050
CHECKING THE CYLINDER HEAD

BREATHER HOSE
1. Remove:
Rider seat
Fuel tank
Air filter case
3-17
ENGINE
3. Install:
Right side cover
EAS21080
CHECKING THE EXHAUST SYSTEM

The following procedure applies to all of the exhaust pipes and gaskets.
1. Check:
Front exhaust pipe 1
Rear exhaust pipe 2
Muffler 3
Muffler bracket 4
Gaskets 5
Exhaust gas leaks Replace.
2. Check:
Tightening torque
Front exhaust pipe nuts 6
7
Rear exhaust pipe nuts 8
Rear exhaust pipe and muffler bolt 9
Muffler and muffler bracket bolts 10
Muffler bracket and frame bolts 11
10
4
LT
LT
11
8
9
5
5
2
7
6
1
EAS21090
T.
R.
CHECKING THE CANISTER (for California

only)
1. Remove:
Horn 1
Refer to THROTTLE BODIES on page 6-6.
2. Check:
Canister 1
Canister purge hose 2
Canister breather hose 3
Fuel tank breather/overflow hose 4
Front exhaust pipe nut

20 Nm (2.0 mkg, 14 ftlb)
20 Nm (2.0 mkg, 14 ftlb)
Rear exhaust pipe nut
24 Nm (2.4 mkg, 17 ftlb)
Rear exhaust pipe and muffler
bolt
20 Nm (2.0 mkg, 14 ftlb)
Muffler and muffler bracket bolt
29 Nm (2.9 mkg, 21 ftlb)
Muffler bracket and frame bolt
53 Nm (5.3 mkg, 38 ftlb)
LOCTITE
4
1
3
3. Install:
Horn 1
EAS21100
ADJUSTING THE EXUP CABLES

1. Remove:
EXUP valve pulley cover 1
3-18
ENGINE
a. Loosen both locknuts 1.
1
1
2. Check:
EXUP system operation
b. Turn both adjusting bolts 2 in or out until the

specification.
a. Turn the main switch to ON.

b. Check that the EXUP valve operates properly.
Turn in a
Free play is increased.
Turn out b
Free play is decreased.
NOTE:
Check that the projection a on the EXUP valve

pulley contact the stopper b (fully-open position) and the stopper c (fully-closed position).
a
b
a
a
2
c
c. Tighten both locknuts.
d. Turn the main switch to ON and check that
the projection c on the EXUP valve pulley
contacts the stoppers (fully open and fully
closed positions), then stops between the
lines d on the cable holder.
3. Check:
EXUP cable free play (at the EXUP valve pulley) a and b
EXUP cable free play (at the
EXUP valve pulley)
a: 3 mm (0.12 in) or less
b: 3 mm (0.12 in) or less
5. Install:
EXUP valve pulley cover
T.
4. Adjust:
EXUP cable free play
R.
3-19
EXUP valve pulley cover bolt

7 Nm (0.7 mkg, 5.1 ftlb)
CHASSIS
EAS21140
CHASSIS
2
EAS21190
ADJUSTING THE REAR DISC BRAKE

1. Check:
(distance a from the top of the rider footrest
to the top of the brake pedal)

110.0 mm (4.33 in)
c. Tighten the locknut.

EW1D71005
WARNING
A soft or spongy feeling in the brake pedal

can indicate the presence of air in the brake
system. Before the vehicle is operated, the
air must be removed by bleeding the brake
system. Air in the brake system will considerably reduce braking performance.
ECA13510
CAUTION:
After adjusting the brake pedal position,

make sure there is no brake drag.
2. Adjust:
3. Adjust:
Rear brake light switch
Refer to ADJUSTING THE REAR BRAKE
LIGHT SWITCH on page 3-22.

b. Turn the adjusting bolt 2 in direction a or
b until the specified brake pedal position is
obtained.
EAS21240
Direction a
Brake pedal is raised.
Direction b
Brake pedal is lowered.
CHECKING THE BRAKE FLUID LEVEL

NOTE:

EWA13070
WARNING
2. Remove:
Rider seat
3. Check:
Brake fluid level
recommended brake fluid to the proper level.
After adjusting the brake pedal position,

check that the end of the adjusting bolt c is
visible through the hole d.
1
Front brake
Recommended fluid
DOT 4
Rear brake
Recommended fluid
DOT 4
b
2
3-20
CHASSIS
EAS21250
CHECKING THE FRONT BRAKE PADS

brake pads.
1. Operate the brake.
2. Check:
Front brake pad
Wear indicator grooves 1 almost disappeared Replace the brake pads as a set.
Refer to FRONT BRAKE on page 4-31.
B
A. Front brake
B. Rear brake
EAS21260
CHECKING THE REAR BRAKE PADS

brake pads.
1. Operate the brake.
2. Check:
Rear brake pad
Wear indicators 1 almost touch the brake
disc Replace the brake pads as a set.
Refer to REAR BRAKE on page 4-43.
EWA13090
WARNING
Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to
brake performance.
Refill with the same type of brake fluid that
is already in the system. Mixing brake fluids
may result in a harmful chemical reaction,
leading to poor brake performance.
not enter the brake fluid reservoir. Water
the brake fluid and could cause vapor lock.
ECA13540
CAUTION:
Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.
EAS21280
CHECKING THE FRONT BRAKE HOSES

brake hoses and brake hose clamps.
1. Check:
Brake hoses 1
Cracks/damage/wear Replace.
NOTE:
In order to ensure a correct reading of the brake

fluid level, make sure the top of the brake fluid
reservoir is horizontal.
4. Install:
Rider seat
3-21
CHASSIS
EAS21330
ADJUSTING THE REAR BRAKE LIGHT

SWITCH
NOTE:
The rear brake light switch is operated by movement of the brake pedal. The rear brake light
switch is properly adjusted when the brake light
comes on just before the braking effect starts.
1. Check:
Rear brake light operation timing
Incorrect Adjust.
2. Adjust:
2. Check:
Brake hose clamps
Loose Tighten the clamp bolt.
3. Hold the vehicle upright and apply the brake
several times.
4. Check:
Brake hoses
Brake fluid leakage Replace the damaged
hose.
Refer to FRONT BRAKE on page 4-31.
a. Hold the main body 1 of the rear brake light

switch so that it does not rotate and turn the
adjusting nut 2 in direction a or b until the
rear brake light comes on at the proper time.
Direction a
Brake light comes on sooner.
Direction b
Brake light comes on later.
EAS21290
CHECKING THE REAR BRAKE HOSES

1. Remove:
Rider seat
2. Check:
Brake hoses 1
1
2
a
EAS21350
BLEEDING THE HYDRAULIC BRAKE

SYSTEM
EWA13100
3. Check:
Brake hose clamp
Loose connection Tighten the clamp bolt.
4. Check:
Brake hose guide
Loose Tighten the guide bolt.
5. Hold the vehicle upright and apply the brake
several times.
6. Check:
Brake hoses
Brake fluid leakage Replace the damaged
hose.
WARNING
Bleed the hydraulic brake system whenever:

the system is disassembled.
a brake hose is loosened, disconnected or
replaced.
the brake fluid level is very low.
brake operation is faulty.
1. Remove:
Rider seat
3-22
CHASSIS
NOTE:
NOTE:
Be careful not to spill any brake fluid or allow

the brake master cylinder reservoir or brake
fluid reservoir to overflow.
When bleeding the hydraulic brake system,
make sure there is always enough brake fluid
before applying the brake. Ignoring this precaution could allow air to enter the hydraulic
brake system, considerably lengthening the
bleeding procedure.
If bleeding is difficult, it may be necessary to let
the brake fluid settle for a few hours. Repeat
the bleeding procedure when the tiny bubbles
in the hose have disappeared.
Loosening the bleed screw will release the pressure and cause the brake lever to contact the
throttle grip or the brake pedal to fully extend.
h. Tighten the bleed screw and then release the
brake lever or brake pedal.
i. Repeat steps (e) to (h) until all of the air bubbles have disappeared from the brake fluid in
the plastic hose.
j. Tighten the bleed screw to specification.
T.
R.
2. Bleed:
Hydraulic brake system

6 Nm (0.6 mkg, 4.3 ftlb)
6 Nm (0.6 mkg, 4.3 ftlb)
k. Fill the brake fluid reservoir to the proper level

with the recommended brake fluid.
Refer to CHECKING THE BRAKE FLUID
LEVEL on page 3-20.
a. Fill the brake fluid reservoir to the proper level

with the recommended brake fluid.
b. Install the diaphragm (brake master cylinder
reservoir or brake fluid reservoir).
c. Connect a clear plastic hose 1 tightly to the
bleed screw 2.
EWA13110
WARNING
After bleeding the hydraulic brake system,

check the brake operation.
3. Install:
Rider seat
EAS21380
ADJUSTING THE SHIFT PEDAL

NOTE:
The shift pedal position is determined by the installed shift rod length a.
B
1. Measure:
Installed shift rod length a
Incorrect Adjust.
Installed shift rod length

312.0316.0 mm (12.2812.44 in)
1
A. Front
B. Rear
d. Place the other end of the hose into a container.

e. Slowly apply the brake several times.
f. Fully pull the brake lever or fully press down
the brake pedal and hold it in position.
g. Loosen the bleed screw.
2. Adjust:
Installed shift rod length
3-23
CHASSIS
a. Loosen both locknuts 1.

b. Turn the shift rod 2 in direction a or b until
the specified installed shift rod length is obtained.
NOTE:
Place the vehicle on the sidestand and or on a

suitable stand so that the rear wheel is elevated.
2. Check:
Drive belt slack a
Direction a
Installed shift rod length increases.
Direction b
Installed shift rod length decreases.
1
a
a
b
2
Drive belt slack (on the sidestand)
7.513 mm (0.300.51 in)
Drive belt slack (on a suitable
stand)
1421 mm (0.550.83 in)
c. Tighten both locknuts.
T.
R.
Locknut (shift rod)

12 Nm (1.2 mkg, 8.7 ftlb)
Belt tension gauge

90890-03170
Rear drive belt tension gauge
YM-03170
d. Make sure the installed shift rod length is

within specification.
EAS21430
ADJUSTING THE DRIVE BELT SLACK
NOTE:
NOTE:
The level marks of the level window on the lower drive belt cover are in units of 5 mm (0.20 in).
Use them as a standard for measuring the
drive belt slack.
Measure the drive belt slack when the drive
belt has been pushed with 4.5 kg (10 lbs) of
pressure using a belt tension gauge 1.
The drive belt slack must be checked at the tightest point on the belt.
ECA14950
CAUTION:
A drive belt that is too tight will overload the

engine and other vital parts, and one that is
too loose can skip and damage the swingarm or cause an accident. Therefore, keep
the drive belt slack within the specified limits.
NOTE:
Measure the drive belt slack when the engine is

cold, and when the drive belt is dry.

EWA13120
WARNING
3. Remove:
Muffler
4. Adjust:
Drive belt slack
Securely support the vehicle so that there is

no danger of it falling over.
3-24
CHASSIS
5. Install:
Muffler
NOTE:
Place the vehicle on a suitable stand so that the

rear wheel is elevated.
EWA12800
WARNING
a. Loosen the wheel axle nut 1.
Always use a new gasket.

EAS21510
CHECKING AND ADJUSTING THE

STEERING HEAD
EWA13120
WARNING

1
b. Loosen both locknuts 2.
c. Turn both adjusting bolts 3 in direction a or
b until the specified drive belt slack is obtained.
NOTE:

front wheel is elevated.
2. Check:
Steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding/looseness Adjust the steering
head.
Direction a
Drive belt is tightened.
Direction b
Drive belt is loosened.
b
3
2
3. Remove:
Upper bracket
Refer to FRONT FORK on page 4-60.
4. Adjust:
Steering head
NOTE:
Using the alignment marks on each side of the

swingarm, make sure that both belt pullers are in
the same position for proper wheel alignment.
d. Tighten the locknuts to specification.
a. Remove the lock washer 1, the upper ring

nut 2, and the rubber washer 3.
T.
R.
Locknut (drive belt adjusting

bolt)
16 Nm (1.6 mkg, 11 ftlb)
e. Tighten the rear wheel axle nut to specification.
T.
R.
Rear wheel axle nut

150 Nm (15.0 mkg, 110 ftlb)
3-25
CHASSIS
b. Loosen the lower ring nut 4, and then tighten it to the specified torque with a steering nut
wrench 5.
NOTE:
Make sure the lock washer tabs a sit correctly

in the ring nut slots b.
NOTE:
Set a torque wrench at a right angle to the steering nut wrench.

Steering nut wrench
90890-01403
Spanner wrench
YU-33975
T.
R.
Lower ring nut (initial tightening

torque)
52 Nm (5.2 mkg, 37 ftlb)
5. Install:
Upper bracket
EAS21530
CHECKING THE FRONT FORK

EWA13120
WARNING

2. Check:
Inner tube
Damage/scratches Replace.
Oil seal
Oil leakage Replace.
3. Hold the vehicle upright and apply the front
brake.
4. Check:
Front fork operation
Push down hard on the handlebar several
times and check if the front fork rebounds
smoothly.
Rough movement Repair.
c. Loosen the lower ring nut completely, and

then tighten it to specification with a steering
nut wrench.
EWA13140
WARNING
Do not overtighten the lower ring nut.
T.
R.
Lower ring nut (final tightening

torque)
18 Nm (1.8 mkg, 13 ftlb)
d. Check the steering head for looseness or

binding by turning the front fork all the way in
both directions. If any binding is felt, remove
the lower bracket and check the upper and
lower bearings.
Refer to STEERING HEAD on page 4-69.
e. Install the rubber washer 3.
f. Install the upper ring nut.
g. Finger tighten the upper ring nut 2, then
align the slots of both ring nuts. If necessary,
hold the lower ring nut and tighten the upper
ring nut until their slots are aligned.
h. Install the lock washer 1.
3-26
CHASSIS
EAS21590
ADJUSTING THE REAR SHOCK ABSORBER

ASSEMBLY
EWA13120
WARNING

b
Spring preload
ECA13590
CAUTION:
Never go beyond the maximum or minimum

adjustment positions.
1. Adjust:
Spring preload
NOTE:
Adjust the spring preload with the special

wrench 1.

b. Turn the adjusting ring 3 in direction a or
b.
c. Installed spring length
c. Tighten the locknut to specification.
T.
Direction a
Spring preload is increased (suspension is harder).
Direction b
Spring preload is decreased (suspension is softer).
R.
Locknut (rear shock absorber

spring preload adjusting nut)
30 Nm (3.0 mkg, 22 ftlb)
ECA13600
CAUTION:
Always tighten the locknut against the adjusting nut and torque it to specification.
Spring preload adjusting positions

Installed spring length
Minimum
162.0 mm (6.38 in)
Standard
171.0 mm (6.73 in)
XV19CTSV(C)/XV19CTV(C)/
XV19CTMV(C):
165.0 mm (6.50 in)
Maximum
171.0 mm (6.73 in)
EAS21650
CHECKING THE TIRES

The following procedure applies to both of the
tires.
1. Check:
Tire pressure
Out of specification Regulate.
3-27
CHASSIS
2. Check:
Tire surfaces
Damage/wear Replace the tire.
EWA13180
WARNING
The tire pressure should only be checked

and regulated when the tire temperature
equals the ambient air temperature.
The tire pressure and the suspension must
be adjusted according to the total weight
(including cargo, rider, passenger and accessories) and the anticipated riding
speed.
Operation of an overloaded vehicle could
cause tire damage, an accident or an injury.
NEVER OVERLOAD THE VEHICLE.
Wear limit (front)

1.0 mm (0.04 in)
Wear limit (rear)
1.0 mm (0.04 in)
Tire air pressure (measured on

cold tires)
Loading condition
090 kg (0198 lb)
Front
250 kPa (36 psi) (2.50 kgf/cm)
Rear
280 kPa (41 psi) (2.80 kgf/cm)
Loading condition
90210 kg (198463 lb)
XV19CTMV(C):
90186 kg (198410 lb)
Front
250 kPa (36 psi) (2.50 kgf/cm)
Rear
280 kPa (41 psi) (2.80 kgf/cm)
High-speed riding
Front
250 kPa (36 psi) (2.50 kgf/cm)
Rear
280 kPa (41 psi) (2.80 kgf/cm)
Maximum load
210 kg (463 lb)
XV19CTMV(C):
186 kg (410 lb)
* Total weight of rider, passenger, cargo
and accessories
1. Tire tread depth

2. Side wall
3. Wear indicator
EWA14080
WARNING
Do not use a tubeless tire on a wheel designed only for tube tires to avoid tire failure and personal injury from sudden
deflation.
When using a tube tire, be sure to install the
correct tube.
Always replace a new tube tire and a new
tube as a set.
To avoid pinching the tube, make sure the
wheel rim band and tube are centered in the
wheel groove.
Patching a punctured tube is not recommended. If it is absolutely necessary to do
so, use great care and replace the tube as
soon as possible with a good quality replacement.
EWA13190
WARNING
It is dangerous to ride with a worn-out tire.

When the tire tread reaches the wear limit, replace the tire immediately.
A. Tire
B. Wheel
3-28
CHASSIS
Tube wheel
Tube tire only
Tubeless wheel
Tube or tubeless tire
EWA14090
WARNING
After extensive tests, the tires listed below

have been approved by Yamaha Motor Co.,
Ltd. for this model. The front and rear tires
should always be by the same manufacturer
and of the same design. No guarantee concerning handling characteristics can be given if a tire combination other than one
approved by Yamaha is used on this vehicle.
EAS21670
CHECKING THE WHEELS

wheels.
1. Check:
Wheel
Damage/out-of-round Replace.
Front tire
Size
130/70R18M/C 63H
Manufacturer/model
DUNLOP/D251F
Manufacturer/model
Rear tire
Size
190/60R17M/C 78H
Manufacturer/model
DUNLOP/D251
Manufacturer/model
EWA13260
WARNING
Never attempt to make any repairs to the

wheel.
NOTE:
After a tire or wheel has been changed or replaced, always balance the wheel.
EAS21690
CHECKING AND LUBRICATING THE

CABLES
The following procedure applies to all of the inner and outer cables.
EWA13210
WARNING
EWA13270
New tires have a relatively low grip on the

road surface until they have been slightly
worn. Therefore, approximately 100 km
should be traveled at normal speed before
any high-speed riding is done.
WARNING
Damaged outer cable may cause the cable to

corrode and interfere with its movement. Replace damaged outer cable and inner cables
as soon as possible.
NOTE:
1. Check:
Outer cable
Damage Replace.
2. Check:
Cable operation
Rough movement Lubricate.
For tires with a direction of rotation mark 1:

Install the tire with the mark pointing in the direction of wheel rotation.
Align the mark 2 with the valve installation
point.
Recommended lubricant
Engine oil or a suitable cable lubricant
NOTE:
Hold the cable end upright and pour a few drops

of lubricant into the cable sheath or use a suitable lubricating device.
3-29
CHASSIS
EAS21700
LUBRICATING THE LEVERS

Lubricate the pivoting point and metal-to-metal
moving parts of the levers.
Lithium-soap-based grease
EAS21710
LUBRICATING THE PEDAL

moving parts of the pedal.
EAS21720
LUBRICATING THE SIDESTAND

moving parts of the sidestand.
EAS21740
LUBRICATING THE REAR SUSPENSION

moving parts of the rear suspension.
NOTE:
Lubricate the pivoting points and contact surfaces between the connecting rod and frame and
between the swingarm and frame.
3-30
ELECTRICAL SYSTEM
5. Replace:
Low beam headlight bulb
EAS21750
ELECTRICAL SYSTEM
a. Disconnect:
Headlight coupler 1
b. Remove:
Headlight bulb 2
EAS21760
CHECKING AND CHARGING THE BATTERY

Refer to ELECTRICAL COMPONENTS on
page 7-67.
EWA13320
EAS21770
WARNING
CHECKING THE FUSES

Refer to ELECTRICAL COMPONENTS on
page 7-67.
Since the headlight bulb gets extremely hot,

keep flammable products and your hands
away from the bulb until it has cooled down.
EAS21790
REPLACING THE HEADLIGHT BULBS

1. Remove:
Windshield (For XV19CTSV(C)/
XV19CTV(C)/XV19CTMV(C) only)
2. Remove:
Headlight cover 1
1
1
c. Install:
Headlight bulb New
Secure the new headlight bulb with the headlight bulb holder.
ECA13690
CAUTION:
Avoid touching the glass part of the headlight bulb to keep it free from oil, otherwise
the transparency of the glass, the life of the
bulb and the luminous flux will be adversely
affected. If the headlight bulb gets soiled,
thoroughly clean it with a cloth moistened
with alcohol or lacquer thinner.
3. Disconnect:
Air temperature sensor coupler 1
d. Connect:
Headlight coupler
6. Replace:
High beam headlight bulb
4. Remove:
Headlight assembly 1
a. Remove:
Headlight bulb cover 1
3-31
ELECTRICAL SYSTEM
7. Install:
Headlight assembly
8. Connect:
Air temperature sensor coupler
9. Install:
Headlight cover
T.
Headlight cover bolt

7 Nm (0.7 mkg, 5.1 ftlb)
R.
10.Install:
Windshield (For XV19CTSV(C)/
XV19CTV(C)/XV19CTMV(C) only)
b. Disconnect:
Headlight coupler 1
c. Detach:
Headlight bulb holder 2
EAS21810
ADJUSTING THE HEADLIGHT BEAMS

1. Adjust:
Headlight beam (vertically)
a. Turn the adjusting bolt 1 in direction a or

b.
Direction a
Headlight beam is raised.
Direction b
Headlight beam is lowered.
2
1
d. Remove:
Headlight bulb
EWA13320
WARNING
Since the headlight bulb gets extremely hot,

away from the bulb until it has cooled down.
e. Install:
b
1
Headlight bulb New

Secure the new headlight bulb with the headlight bulb holder.
ECA13690
CAUTION:
Avoid touching the glass part of the headlight bulb to keep it free from oil, otherwise
the transparency of the glass, the life of the
bulb and the luminous flux will be adversely
affected. If the headlight bulb gets soiled,
2. Adjust:
Headlight beam (horizontally)
a. Turn the adjusting bolt 1 in direction a or

b.
Direction a
Headlight beam moves to the right.
Direction b
Headlight beam moves to the left.
f. Attach:
Headlight bulb holder
g. Connect:
Headlight coupler
h. Install:
Headlight bulb cover
3-32
ELECTRICAL SYSTEM
b
a
3-33
CHASSIS
GENERAL CHASSIS ...................................................................................... 4-1
REMOVING THE WINDSHIELD ............................................................... 4-2
ASSEMBLING THE WINDSHIELD ........................................................... 4-2
INSTALLING THE WINDSHIELD.............................................................. 4-2
REMOVING THE BACKREST .................................................................. 4-5
ASSEMBLING THE BACKREST .............................................................. 4-5
INSTALLING THE BACKREST................................................................. 4-5
CHECKING THE SIDEBAG BRACKET SPRING NUTS........................... 4-8
FRONT WHEEL ............................................................................................ 4-15
REMOVING THE FRONT WHEEL ......................................................... 4-18
DISASSEMBLING THE FRONT WHEEL................................................ 4-18
CHECKING THE FRONT WHEEL .......................................................... 4-18
ASSEMBLING THE FRONT WHEEL...................................................... 4-19
ADJUSTING THE FRONT WHEEL STATIC BALANCE ......................... 4-19
INSTALLING THE FRONT WHEEL (FRONT BRAKE DISCS) ............... 4-20
REAR WHEEL............................................................................................... 4-23
REMOVING THE REAR WHEEL (DISC)................................................ 4-28
DISASSEMBLING THE REAR WHEEL .................................................. 4-28
CHECKING THE REAR WHEEL ............................................................ 4-28
CHECKING THE REAR BRAKE CALIPER BRACKET........................... 4-28
CHECKING THE REAR WHEEL DRIVE HUB........................................ 4-29
CHECKING AND REPLACING THE REAR WHEEL PULLEY ............... 4-29
ASSEMBLING THE REAR WHEEL ........................................................ 4-29
ADJUSTING THE REAR WHEEL STATIC BALANCE ........................... 4-29
INSTALLING THE REAR WHEEL (DISC) .............................................. 4-29
FRONT BRAKE............................................................................................. 4-31
INTRODUCTION..................................................................................... 4-36
CHECKING THE FRONT BRAKE DISCS............................................... 4-36
REPLACING THE FRONT BRAKE PADS .............................................. 4-37
REMOVING THE FRONT BRAKE CALIPERS ....................................... 4-38
DISASSEMBLING THE FRONT BRAKE CALIPERS ............................. 4-38
CHECKING THE FRONT BRAKE CALIPERS........................................ 4-39
ASSEMBLING THE FRONT BRAKE CALIPERS ................................... 4-39
INSTALLING THE FRONT BRAKE CALIPERS...................................... 4-39
REMOVING THE FRONT BRAKE MASTER CYLINDER....................... 4-40
CHECKING THE FRONT BRAKE MASTER CYLINDER ....................... 4-40
ASSEMBLING THE FRONT BRAKE MASTER CYLINDER ................... 4-41
INSTALLING THE FRONT BRAKE MASTER CYLINDER ..................... 4-41
REAR BRAKE............................................................................................... 4-43

INTRODUCTION..................................................................................... 4-49
CHECKING THE REAR BRAKE DISC ................................................... 4-49
REPLACING THE REAR BRAKE PADS ................................................ 4-49
REMOVING THE REAR BRAKE CALIPER ............................................ 4-50
DISASSEMBLING THE REAR BRAKE CALIPER .................................. 4-50
CHECKING THE REAR BRAKE CALIPER............................................. 4-51
ASSEMBLING THE REAR BRAKE CALIPER ........................................ 4-51
INSTALLING THE REAR BRAKE CALIPER........................................... 4-51
REMOVING THE REAR BRAKE MASTER CYLINDER ......................... 4-52
CHECKING THE REAR BRAKE MASTER CYLINDER.......................... 4-52
ASSEMBLING THE REAR BRAKE MASTER CYLINDER ..................... 4-53
INSTALLING THE REAR BRAKE MASTER CYLINDER........................ 4-53
HANDLEBAR ................................................................................................ 4-55
REMOVING THE HANDLEBAR.............................................................. 4-57
CHECKING THE HANDLEBAR .............................................................. 4-57
INSTALLING THE HANDLEBAR ............................................................ 4-57
FRONT FORK ............................................................................................... 4-60
REMOVING THE FRONT FORK LEGS.................................................. 4-64
DISASSEMBLING THE FRONT FORK LEGS........................................ 4-64
CHECKING THE FRONT FORK LEGS .................................................. 4-65
ASSEMBLING THE FRONT FORK LEGS.............................................. 4-65
INSTALLING THE FRONT FORK LEGS ................................................ 4-68
STEERING HEAD ......................................................................................... 4-69
REMOVING THE LOWER BRACKET .................................................... 4-71
CHECKING THE STEERING HEAD....................................................... 4-71
INSTALLING THE STEERING HEAD..................................................... 4-71
REAR SHOCK ABSORBER ASSEMBLY AND SWINGARM...................... 4-73
HANDLING THE REAR SHOCK ABSORBER........................................ 4-75
DISPOSING OF A REAR SHOCK ABSORBER ..................................... 4-75
REMOVING THE REAR SHOCK ABSORBER ASSEMBLY AND
SWINGARM ........................................................................................... 4-75
CHECKING THE REAR SHOCK ABSORBER ASSEMBLY ................... 4-76
CHECKING THE CONNECTING ARM AND RELAY ARM..................... 4-76
CHECKING THE SWINGARM ................................................................ 4-76
INSTALLING THE RELAY ARM, REAR SHOCK ABSORBER
ASSEMBLY AND CONNECTING ARMS............................................... 4-76
INSTALLING THE SWINGARM .............................................................. 4-78
BELT DRIVE ................................................................................................. 4-79
REMOVING THE DRIVE BELT AND DRIVE PULLEY ........................... 4-81
CHECKING THE DRIVE BELT ............................................................... 4-81
INSTALLING THE DRIVE BELT AND DRIVE PULLEY.......................... 4-81
GENERAL CHASSIS
EAS21830
GENERAL CHASSIS
Removing the windshield (For XV19CTSV(C)/XV19CTV(C)/XV19CTMV(C))
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)

LT
LT
6
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
LT
LT
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
6
LT
2
3
T.
R.
3
T.
8 Nm (0.8 m kg, 5.8 ft Ib)
R.
T.
T.
R.
12 Nm (1.2 m kg, 8.7 ft Ib)
R.
Order
Job/Parts to remove
23 Nm (2.3 m kg, 17 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)

Qty
Windshield
Windshield bracket brace
Windshield bracket (left and right)
Windshield brace (left and right)
Windshield screen
Windshield holder bracket assembly (left and

right)
Remarks
4-1
GENERAL CHASSIS
ET1D71039
REMOVING THE WINDSHIELD

1. Remove:
Windshield
a. Insert the key 1 into the windshield lock, turn

it clockwise and then remove the key.
2
b
2
1
ET1D71040
INSTALLING THE WINDSHIELD

1. Install:
Right windshield holder bracket assembly 1
NOTE:
Pass the throttle cables 2 between the front

fork and the right windshield holder bracket assembly.
2. Unlock.
b. Remove the windshield by pushing it forward,

and then pulling it upward as shown.
EW1D71016
WARNING
Be careful not to push the vehicle forward

when removing the windshield. The vehicle
could fall off the sidestand.
EC1D71025
CAUTION:
Securely hold the windshield to prevent it

from falling when removing.
2. Install:
Windshield
a. Fit the slot a in each windshield bracket (left

and right side) into its holder b.
NOTE:
Make sure that the throttle cables 1 are not

pinched.
ET1D71045
ASSEMBLING THE WINDSHIELD

1. Install:
Windshield lock 1
NOTE:
Align the projection a on the lock 1 with the

slot b in the windshield bracket 2.
1
b. Push the windshield backward until it snaps
into place.
4-2
GENERAL CHASSIS
c. Insert the key into the windshield lock, turn it

counterclockwise until it stops to lock the fastener, and then remove the key.
1. Lock
2. Fastener
4-3
GENERAL CHASSIS
Removing the sidebags and backrest (For XV19CTSV(C)/XV19CTV(C)/XV19CTMV(C))
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
4
6
2
7
1
5
7
1
T.
R.
Order
Job/Parts to remove
12 Nm (1.2 m kg, 8.7 ft Ib)
Qty
Remarks
NOTE:
Sidebag (left and right)
Backrest assembly
Backrest upper bracket stay
Backrest pad
Backrest plate
Backrest upper bracket
Backrest lower bracket (left and right)
Water can be harmful to untreated leather.

Use Yamaha Saddle Soap or another quality
brand according to the manufacturers directions to clean the leather on the sidebags.
Polish the dry leather with a soft cloth, and
then treat with Yamaha Mink Oil or another
high-quality leather protectant for increased
water resistance.
4-4
GENERAL CHASSIS
ET1D71041
NOTE:
REMOVING THE BACKREST

1. Remove:
Backrest
Align the projection a on the lock 1 with the

slot b in the left backrest lower bracket 2.
a. Open the sidebag lids.

b. Insert the key 1 into the backrest lock, turn
it counterclockwise, and then remove the
key.
a
1
2
2
2. Install:
Backrest lower brackets 1
Backrest upper bracket 2
Backrest plate
NOTE:
2. Unlock.
Before tightening the bolts 3 to specification,

temporarily install the backrest lower brackets
on the backrest holders, making sure not to push
down on the rear of the brackets. The lower bolts
cannot be tightened when the backrest lower
brackets are installed completely.
c. Pull the lever 1 on each side of the backrest

upward.
2
1
1
d. While holding the levers in the upward position, lift the backrest upward and remove it by
pulling it to the rear.
ET1D71042
INSTALLING THE BACKREST

1. Install:
Backrest
a. Fit the slot a on each backrest bracket (left

and right side) into the groove of its holder b.
EC1D71026
CAUTION:
Be careful not to scratch the rear fender

when fitting the slot into the groove.
ET1D71046
ASSEMBLING THE BACKREST

1. Install:
Backrest lock 1
4-5
GENERAL CHASSIS
b
a
b. Push the rear of the backrest down smoothly

but forcefully to lock it in place and make sure
that the lever hook 1 on each side is securely fit over its holder 2.
EW1D71017
WARNING
Both lever hooks must be securely fitted

over their holder. If the backrest is loose, a
passenger might lose balance and fall.
2
c. Insert the key into the backrest lock, turn it
clockwise, and then remove the key.
4-6
GENERAL CHASSIS
Removing the sidebag brackets (For XV19CTSV(C)/XV19CTV(C)/XV19CTMV(C))
T.
R.
47 Nm (4.7 m kg, 34 ft Ib)
TLT
L
4
LT
LT
3
2
T.
R.
R.
R.
47 Nm (4.7 m kg, 34 ft Ib)
T.
T.
Order
23 Nm (2.3 m kg, 17 ft Ib)
Job/Parts to remove
Qty
23 Nm (2.3 m kg, 17 ft Ib)
Remarks
Refer to GENERAL CHASSIS on page
4-1.
Sidebag/Backrest
1
Passenger footrest (left and right)
Sidebag bracket brace
NOTE:
3
Sidebag bracket (left and right)
O2 sensor lead guide
Remove only one sidebag bracket at a time.

If both brackets are removed at the same
time, the rear fender will fall.
4-7
GENERAL CHASSIS
ET1D71047
CHECKING THE SIDEBAG BRACKET

SPRING NUTS
1. Check:
Sidebag bracket spring nut height a
Sidebag bracket spring nut
height
12.0 mm (0.47 in)
2. Check:
Sidebag bracket spring nuts
Damage Replace.
4-8
GENERAL CHASSIS
Removing the seats and side covers
T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
2
3
1
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
R.
LT
6
4
T.
23 Nm (2.3 m kg, 17 ft Ib)
R.
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
LT
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
8
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
T.
R.
Order
Job/Parts to remove
Qty
Rider seat
Passenger seat
Tool kit
Tool kit tray
Right side cover
Left side cover
Seat lock cable assembly
7 Nm (0.7 m kg, 5.1 ft Ib)

Remarks
4-9
GENERAL CHASSIS
Removing the headlight
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
1
13
10
10
9
6
5
12
4
11
T.
R.
Order
7 Nm (0.7 m kg, 5.1 ft Ib)
Job/Parts to remove
Qty
Remarks
Headlight cover
Air temperature sensor
Headlight (low beam) coupler
Disconnect.
Headlight (high beam) coupler
Disconnect.
Headlight lens unit
Front left turn signal/position light coupler
Disconnect.
Front right turn signal/position light coupler
Disconnect.
Wire harness stopper bracket
Disconnect.
10
Left handlebar switch coupler
Disconnect.
11
Right handlebar switch coupler
Disconnect.
12
Main switch coupler
Disconnect.
13
Headlight body
1
4-10
GENERAL CHASSIS
Removing the battery
10
2
9
16
17
18
15
13
(3)
11
14
19
12
20
19
Order
Job/Parts to remove
Qty
Remarks
4-1.
Tool kit tray/Seat bracket

1
ECU band
ECU (electronic control unit)
Coupler tray
Negative terminal cover
Negative battery lead
Disconnect.
Positive battery lead
Disconnect.
Battery
Battery band
Sub-wire harness 1
10
Main fuse
11
Plastic locking tie
12
Fuse box
13
Starter relay coupler
14
Starter relay
15
Diode 1
16
Relay unit
4-11
Disconnect.
Disconnect.
GENERAL CHASSIS
Removing the battery
10
2
9
16
17
18
15
13
(3)
11
14
19
12
20
19
Order
17
Job/Parts to remove
Qty
Headlight relay
Remarks
18
Turn signal relay
19
Plastic locking tie
20
Battery box
1
4-12
GENERAL CHASSIS
Removing the air filter case
T.
T.
R.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
(7)
9
1
2
15
10
7
16
13
8
12
14
17
16
3
11
4
Order
Job/Parts to remove
Qty
Remarks
Rider seat

4-1.
Fuel tank
Pressure regulator cover
Air filter case cover
Air filter element
Cylinder-#1 intake air pressure sensor coupler
Disconnect.
Disconnect.
Cylinder-#1 intake air pressure sensor bracket
Disconnect.
Disconnect.
10
Cylinder-#2 intake air pressure sensor bracket
11
Cylinder head breather hose
Disconnect.
12
Disconnect.
13
Disconnect.
14
Disconnect.
4-13
GENERAL CHASSIS
Removing the air filter case
T.
T.
R.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
(7)
9
1
2
15
10
7
16
13
8
12
14
17
16
3
11
4
Order
Job/Parts to remove
Qty
15
Air filter case bracket
16
Air filter case joint clamp screw
17
Air filter case
Remarks
Loosen.
4-14
FRONT WHEEL
EAS21870
FRONT WHEEL
Removing the front wheel and brake discs
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
40 Nm (4.0 m kg, 29 ft Ib)
R.
T.
40 Nm (4.0 m kg, 29 ft Ib)
R.
R.
LT
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
9
5
LT
10
4
6
(4)
LT
T.
LT
9
11
LT
R.
10
16 Nm (1.6 m kg, 11 ft Ib)
12
T.
R.
R.
T.
R.
15
T.
14
72 Nm (7.2 m kg, 52 ft Ib)
16
(6)
23 Nm (2.3 m kg, 17 ft Ib)
7 Nm (0.7 m kg, 5.1 ft Ib)
LT
LT
16
LT
T.
R.
13
LT
7 Nm (0.7 m kg, 5.1 ft Ib)
14
LT
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
R.
Job/Parts to remove
T.
Order
(6)
23 Nm (2.3 m kg, 17 ft Ib)
Qty
Remarks
NOTE:
Place the vehicle on a suitable stand so that
the front wheel is elevated.
1
Right front fender stay
Left front fender stay
Front fender stay rod
Front brake hose guide
Right front brake hose guide bracket
Left front brake hose guide bracket
Front fender
Reflector
Reflector bracket
10
Front brake caliper
11
12
Front wheel axle
13
Front wheel
4-15
Loosen.
FRONT WHEEL
Removing the front wheel and brake discs
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
40 Nm (4.0 m kg, 29 ft Ib)
R.
T.
40 Nm (4.0 m kg, 29 ft Ib)
T.
R.
LT
R.
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)
9
5
LT
10
4
6
(4)
LT
T.
LT
R.
9
11
LT
8
10
16 Nm (1.6 m kg, 11 ft Ib)
12
T.
R.
R.
T.
R.
15
T.
14
72 Nm (7.2 m kg, 52 ft Ib)
16
(6)
23 Nm (2.3 m kg, 17 ft Ib)
7 Nm (0.7 m kg, 5.1 ft Ib)
LT
LT
16
LT
T.
R.
13
LT
7 Nm (0.7 m kg, 5.1 ft Ib)
14
LT
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
R.
14
Job/Parts to remove
T.
Order
(6)
Qty
Collar
15
Front brake disc cover
16
Front brake disc
23 Nm (2.3 m kg, 17 ft Ib)

Remarks
4-16
FRONT WHEEL
Disassembling the front wheel
New 1
LS
3
2
1 New
LS
Order
Job/Parts to remove
Qty
Oil seal
Wheel bearing
Spacer
Remarks
For assembly, reverse the disassembly procedure.
4-17
FRONT WHEEL
EAS21900
EAS21910
REMOVING THE FRONT WHEEL

DISASSEMBLING THE FRONT WHEEL

1. Remove:
Oil seals
Wheel bearings
EWA13120
WARNING

2. Remove:
Right front fender stay 1
Left front fender stay 2
Front fender stay rod 3
a. Clean the outside of the front wheel hub.

b. Remove the oil seals 1 with a flathead
screwdriver.
NOTE:
To prevent damaging the wheel, place a rag 2

between the screwdriver and the wheel surface.
NOTE:
Remove the right front fender stay bolts and

left front fender stay bolt (rear side), then hold
the rod with a wrench 4 and remove the left
front fender stay bolt (front side) 5.
Remove the rod from the right side of the vehicle.
c. Remove the wheel bearings 3 with a general bearing puller.
3
2
5
3. Loosen:
Front wheel axle pinch bolt 1
EAS21920
CHECKING THE FRONT WHEEL

1. Check:
Front wheel axle
Roll the wheel axle on a flat surface.
Bends Replace.
1
4. Remove:
Front brake calipers
EWA13460
WARNING
NOTE:
Do not attempt to straighten a bent wheel axle.
Do not apply the brake lever when removing the

brake calipers.
5. Elevate:
Front wheel
NOTE:

4-18
FRONT WHEEL
EAS21960
ASSEMBLING THE FRONT WHEEL

1. Install:
Wheel bearings New
Oil seals New
a. Install the new wheel bearings and oil seals in

the reverse order of disassembly.
EC1D71011
CAUTION:
2. Check:
Tire
Front wheel
Damage/wear Replace.
Refer to CHECKING THE TIRES on page
3-27 and CHECKING THE WHEELS on
page 3-29.
3. Measure:
Radial wheel runout 1
Lateral wheel runout 2
Over the specified limits Replace.
Do not contact the wheel bearing inner race

1 or balls 2. Contact should be made
only with the outer race 3.
NOTE:
Use a socket 4 that matches the diameter of

the wheel bearing outer race and oil seal.

1.0 mm (0.04 in)
0.5 mm (0.02 in)
EAS21970
ADJUSTING THE FRONT WHEEL STATIC

BALANCE
NOTE:
After replacing the tire, wheel or both, the front

wheel static balance should be adjusted.
Adjust the front wheel static balance with the
brake disc installed.
4. Check:
Wheel bearings
Front wheel turns roughly or is loose Replace the wheel bearings.
Oil seals
1. Remove:
Balancing weight(s)
2. Find:
Front wheels heavy spot
NOTE:
Place the front wheel on a suitable balancing

stand.
a. Spin the front wheel.

b. When the front wheel stops, put an X1 mark
at the bottom of the wheel.
4-19
FRONT WHEEL
c. Turn the front wheel 90 so that the X1 mark

is positioned as shown.
d. Release the front wheel.
e. When the wheel stops, put an X2 mark at
the bottom of the wheel.
c. If the heavy spot does not stay in that position, install a heavier weight.
d. Repeat steps (b) and (c) until the front wheel
is balanced.
4. Check:
Front wheel static balance
a. Turn the front wheel and make sure it stays at

each position shown.
f. Repeat steps (d) through (f) several times until all the marks come to rest at the same spot.
g. The spot where all the marks come to rest is
the front wheels heavy spot X.
b. If the front wheel does not remain stationary

at all of the positions, rebalance it.
3. Adjust:
Front wheel static balance
a. Install a balancing weight 1 onto the rim exactly opposite the heavy spot X.
EAS22000
INSTALLING THE FRONT WHEEL (FRONT

BRAKE DISCS)
front brake discs.
1. Install:
Front brake disc
Front brake disc cover
NOTE:
Start with the lightest weight.
T.
R.

23 Nm (2.3 mkg, 17 ftlb)
LOCTITE
NOTE:
Tighten the front brake disc bolts in stages and

in a crisscross pattern.
b. Turn the front wheel 90 so that the heavy

spot is positioned as shown.
4-20
FRONT WHEEL
T.
R.

40 Nm (4.0 mkg, 29 ftlb)
EWA13500
WARNING
Make sure the brake hose is routed properly.
2. Check:
Front brake discs
Refer to CHECKING THE FRONT BRAKE
DISCS on page 4-36.
3. Lubricate:
Oil seal lips
7. Install:
Front fender
Left front brake hose guide bracket
Right front brake hose guide bracket
NOTE:
Temporarily tighten the front fender bolts.

Apply locking agent (LOCTITE) to the threads
of the front fender bolts.
8. Install:
Front fender stay rod 1
Left front fender stay 2
Right front fender stay 3
4. Install:
Front wheel axle
NOTE:
Insert the rod into the front wheel axle from the
right side of the vehicle.
Tighten the left front fender stay bolt (front
side) 4 to specification while holding the rod
with a wrench 5, and then tighten the left front
fender stay bolt (rear side) and right front fender stay bolts to specification.
NOTE:
Install the tire and wheel with the mark 1 pointing in the direction of wheel rotation.
1
2
5. Tighten:
Front wheel axle
4
5
9. Tighten:
Front fender bolts
T.
R.
Front wheel axle

72 Nm (7.2 mkg, 52 ftlb)
23 Nm (2.3 mkg, 17 ftlb)
T.
R.
EC1D71004
CAUTION:
Before tightening the wheel axle, push down

hard on the handlebar several times and
check if the front fork rebounds smoothly.
6. Install:
Front brake calipers
4-21
Front fender bolt

16 Nm (1.6 mkg, 11 ftlb)
LOCTITE
FRONT WHEEL
4-22
REAR WHEEL
EAS22020
REAR WHEEL
Removing the rear fender
LT
LT
4
LT 3
LT
3
2
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
T.
R.
40 Nm (4.0 m kg, 29 ft Ib)
Order
Job/Parts to remove
Qty
Remarks
4-1.
Rider seat/Passenger seat/Tool kit tray

1
Sub-wire harness 1 coupler
Rear fender bracket
Dowel pin
Rear fender assembly
Disconnect.
4-23
REAR WHEEL
Removing the rear wheel
T.
R.
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
16 Nm (1.6 m kg, 11 ft Ib)

T.
R.
150 Nm (15.0 m kg, 110 ft lb)

T.
R.
27 Nm (2.7 m kg, 19 ft Ib)
10
8 7
1
LS
5
11
2
4
LS
12
4
13
LS
14
15
Order
Job/Parts to remove
Qty
Remarks
NOTE:
Place the vehicle on a suitable stand so that
the rear wheel is elevated.
Muffler
Upper drive belt cover
Rear brake caliper
Rear brake pad
Brake pad spring
Drive belt adjusting locknut
Loosen.
Drive belt adjusting bolt
Loosen.
Rear wheel axle nut
Washer
Rear wheel axle
10
Right drive belt puller
11
Left drive belt puller
12
Rear brake caliper bracket
13
Collar
4-24
Black
REAR WHEEL
Removing the rear wheel
T.
R.
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
16 Nm (1.6 m kg, 11 ft Ib)

T.
R.
T.
150 Nm (15.0 m kg, 110 ft lb)

R.
27 Nm (2.7 m kg, 19 ft Ib)
10
8 7
1
LS
5
11
2
4
LS
12
4
13
LS
14
15
Order
Job/Parts to remove
Qty
14
Collar
15
Rear wheel
Remarks
Silver
4-25
REAR WHEEL
Removing the rear brake disc and rear wheel drive hub
Order
Job/Parts to remove
Qty
Rear brake disc cover
Rear brake disc
Rear wheel pulley
Oil seal
Circlip
Rear wheel drive hub
Circlip
Bearing
Collar
Remarks
10
Bearing
11
Rear wheel drive hub damper
12
Rear wheel
1
4-26
REAR WHEEL
Disassembling the rear wheel
New 4
5
6
LS
3
2
1
Order
Job/Parts to remove
Qty
Collar
Bearing
Spacer
Oil seal
Circlip
Bearing
Remarks
4-27
REAR WHEEL
EAS28760
REMOVING THE REAR WHEEL (DISC)

EWA13120
WARNING

NOTE:

2. Remove:
Rear brake caliper 1
EAS22080
DISASSEMBLING THE REAR WHEEL

1. Remove:
Oil seals
Wheel bearings
Refer to DISASSEMBLING THE FRONT
WHEEL on page 4-18.
NOTE:
Do not depress the brake pedal when removing

the brake caliper.
EAS22090
CHECKING THE REAR WHEEL

1. Check:
Rear wheel axle
Rear wheel
Wheel bearings
Oil seals
Refer to CHECKING THE FRONT WHEEL
on page 4-18.
2. Check:
Tire
Rear wheel
Refer to CHECKING THE TIRES on page
3-27 and CHECKING THE WHEELS on
page 3-29.
3. Measure:
Radial wheel runout
Lateral wheel runout
Refer to CHECKING THE FRONT WHEEL
on page 4-18.
1
3. Loosen:
Drive belt adjusting locknuts 1
Drive belt adjusting bolts 2

1.0 mm (0.04 in)
0.5 mm (0.02 in)
4. Remove:
Rear wheel axle nut 1
Rear wheel axle 2
Rear wheel
NOTE:
ET1D71024
Push the rear wheel forward and remove the

drive belt from the rear wheel pulley.
CHECKING THE REAR BRAKE CALIPER

BRACKET
1. Check:
Rear brake caliper bracket
4-28
REAR WHEEL
EAS22110
EAS22150
CHECKING THE REAR WHEEL DRIVE HUB

1. Check:
Rear wheel drive hub
Rear wheel drive hub dampers
ADJUSTING THE REAR WHEEL STATIC

BALANCE
NOTE:
After replacing the tire, wheel or both, the rear

wheel static balance should be adjusted.
Adjust the rear wheel static balance with the
brake disc and rear wheel drive hub installed.
EAS22130
CHECKING AND REPLACING THE REAR

WHEEL PULLEY
1. Check:
Rear wheel pulley
Surface plating has come off Replace the
rear wheel pulley.
Bent teeth Replace the rear wheel pulley.
2. Replace:
Rear wheel pulley
1. Adjust:
Rear wheel static balance
Refer to ADJUSTING THE FRONT WHEEL
STATIC BALANCE on page 4-19.
EAS28770
INSTALLING THE REAR WHEEL (DISC)

1. Lubricate:
Rear wheel axle
Oil seal lips
a. Remove the self-locking nuts and the rear

wheel pulley.
b. Clean the rear wheel drive hub with a clean
cloth, especially the surfaces that contact the
pulley.
c. Install the new rear wheel pulley.
2. Install:
Rear brake disc
Rear brake disc cover
T.
R.
Rear brake disc bolt

18 Nm (1.8 mkg, 13 ftlb)
LOCTITE
T.
Rear wheel pulley self-locking

nut
95 Nm (9.5 mkg, 68 ftlb)
R.
NOTE:
Tighten the self-locking nuts in stages and in a

crisscross pattern.
NOTE:

of the brake disc bolts.
Tighten the brake disc bolts in stages and in a
crisscross pattern.
LT
EAS22140
ASSEMBLING THE REAR WHEEL

1. Install:
3. Check:
Rear brake disc
Refer to CHECKING THE REAR BRAKE
DISC on page 4-49.
4. Install:
Rear wheel axle
Washer
Rear wheel axle nut
Wheel bearings New

Oil seals New
Refer to ASSEMBLING THE FRONT
WHEEL on page 4-19.
4-29
REAR WHEEL
NOTE:
Temporarily tighten the wheel axle nut.

5. Adjust:
Drive belt slack
Refer to ADJUSTING THE DRIVE BELT
SLACK on page 3-24.
6. Tighten:
Rear wheel axle nut
T.
R.
Rear wheel axle nut

150 Nm (15.0 mkg, 110 ftlb)
7. Install:
Rear brake caliper
T.
R.
Rear brake caliper

27 Nm (2.7 mkg, 19 ftlb)
EWA13500
WARNING
Make sure the brake hose is routed properly.
4-30
FRONT BRAKE
EAS22210
FRONT BRAKE
Removing the front brake pads
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
2
LT
4
6
5
9
T.
R.
40 Nm (4.0 m kg, 29 ft Ib)
T.
R.
6 Nm (0.6 m kg, 4.3 ft Ib)
8
9
Order
Job/Parts to remove
Qty
Remarks
The following procedure applies to both of
the front brake calipers.
Brake hose holder
Reflector
Reflector bracket
Front brake caliper
Brake pad clip
Brake pad pin
Brake pad spring
Brake pad
Brake pad shim
2
4-31
FRONT BRAKE
Removing the front brake master cylinder
2
3
4
LS
T.
R.
30 Nm (3.0 m kg, 22 ft Ib)
10 9
12
6
New
5
7
11
T.
R.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Remarks
Drain.
Refer to BLEEDING THE HYDRAULIC
BRAKE SYSTEM on page 3-22.
Brake fluid
1
Right rearview mirror
Brake master cylinder reservoir cap
Brake master cylinder reservoir diaphragm holder
Brake master cylinder reservoir diaphragm
Brake lever
Brake light switch connector
Brake light switch
Front brake hose union bolt
Copper washer
10
Front brake hose
11
Front brake master cylinder holder
12
Front brake master cylinder
Disconnect.
4-32
FRONT BRAKE
Disassembling the front brake master cylinder
3 New
New
LS
Order
Job/Parts to remove
Qty
Dust boot
Circlip
Brake master cylinder kit
Brake master cylinder body
Remarks
4-33
FRONT BRAKE
Removing the front brake calipers
6
7
5
3 New
.
R.
40 Nm (4.0 m kg, 29 ft Ib)
1
T.
R.
32 Nm (3.2 m kg, 23 ft Ib)
4
2
.
R.
Order
Job/Parts to remove
Qty
LT
3 New
10 Nm (1.0 m kg, 7.2 ft Ib)
Remarks
Drain.
Brake fluid
1
Brake hose holder
Copper washer
Front brake hose
Reflector
Reflector bracket
Front brake caliper
1
4-34
FRONT BRAKE
Disassembling the front brake calipers
Order
Job/Parts to remove
Qty
Remarks
Brake pad clip
Brake pad pin
Brake pad spring
Brake pad
Brake pad shim
Brake caliper piston
Brake caliper piston seal
Bleed screw
1
4-35
FRONT BRAKE
e. Measure the deflection 1.5 mm (0.06 in) below the edge of the brake disc.
EAS22220
INTRODUCTION
EWA14100
WARNING
Disc brake components rarely require disassembly. Therefore, always follow these preventive measures:
Never disassemble brake components unless absolutely necessary.
If any connection on the hydraulic brake
system is disconnected, the entire brake
system must be disassembled, drained,
cleaned, properly filled, and bled after reassembly.
Never use solvents on internal brake components.
Use only clean or new brake fluid for cleaning brake components.
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
Avoid brake fluid coming into contact with
the eyes as it can cause serious injury.
FIRST AID FOR BRAKE FLUID ENTERING
THE EYES:
Flush with water for 15 minutes and get immediate medical attention.
4. Measure:
Brake disc thickness
Measure the brake disc thickness at a few different locations.
Out of specification Replace.
4.5 mm (0.18 in)
EAS22240
CHECKING THE FRONT BRAKE DISCS

The following procedure applies to both brake
discs.
1. Remove:
Front wheel
Refer to FRONT WHEEL on page 4-15.
2. Check:
Brake disc
Damage/galling Replace.
3. Measure:
Brake disc deflection
Out of specification Correct the brake disc
deflection or replace the brake disc.
a. Remove the brake disc.

b. Rotate the brake disc by one bolt hole.
c. Install the brake disc.
T.
R.

0.10 mm (0.0039 in)
5. Adjust:

23 Nm (2.3 mkg, 17ftlb)
LOCTITE
NOTE:

of the brake disc bolts.
Tighten the brake disc bolts in stages and in a
crisscross pattern.
a. Place the vehicle on a suitable stand so that

the front wheel is elevated.
b. Before measuring the front brake disc deflection, turn the handlebar to the left or right to
ensure that the front wheel is stationary.
c. Remove the brake caliper.
d. Hold the dial gauge at a right angle against
the brake disc surface.
4-36
FRONT BRAKE
d. Measure the brake disc deflection.

e. If out of specification, repeat the adjustment
steps until the brake disc deflection is within
specification.
f. If the brake disc deflection cannot be brought
within specification, replace the brake disc.
2. Install:
Brake pad shims
(onto the brake pads)
Brake pads
Brake pad spring
NOTE:
Always install new brake pads, brake pad shims,

and a brake pad spring as a set.
6. Install:
Front wheel
a. Connect a clear plastic hose 1 tightly to the

bleed screw 2. Put the other end of the hose
into an open container.
b. Loosen the bleed screw and push the brake
caliper pistons into the brake caliper with your
finger.
EAS22270
REPLACING THE FRONT BRAKE PADS

The following procedure applies to both brake
calipers.
NOTE:
When replacing the brake pads, it is not necessary to disconnect the brake hose or disassemble the brake caliper.
2
1
1. Measure:
Brake pad wear limit a
Out of specification Replace the brake
pads as a set.
5.5 mm (0.22 in)
Limit
0.5 mm (0.02 in)
5.5 mm (0.22 in)
Limit
0.5 mm (0.02 in)
c. Tighten the bleed screw.
T.
R.

6 Nm (0.6 mkg, 4.3ftlb)
d. Install a new brake pad shim onto each new

brake pad.
e. Install new brake pads and a new brake pad
spring.
NOTE:
The arrow mark a on the brake pad spring

must point in the direction of disc rotation.
4-37
FRONT BRAKE
Front brake hose 4
NOTE:
Put the end of the brake hose into a container

and pump out the brake fluid carefully.
3. Install:
Brake pad pin
Brake pad clips
Front brake caliper
2
3
EAS22350
T.
R.

40 Nm (4.0 mkg, 29 ftlb)
DISASSEMBLING THE FRONT BRAKE

CALIPERS
brake calipers.
1. Remove:
Brake caliper pistons 1
Brake caliper piston seals 2
4. Check:
Brake fluid level
LEVEL on page 3-20.
EW1D71001
WARNING
Do not loosen the bolts 3.
5. Check:
Brake lever operation
Soft or spongy feeling Bleed the brake system.
a. Blow compressed air into the brake hose joint

opening a to force out the pistons from the
brake caliper.
EWA13560
WARNING
EAS22300
Cover the brake caliper pistons with a rag.

Be careful not to get injured when the pistons are expelled from the brake caliper.
Never try to pry out the brake caliper pistons.
REMOVING THE FRONT BRAKE CALIPERS

brake calipers.
NOTE:
Before removing the brake caliper, drain the

brake fluid from the entire brake system.
1. Remove:
Brake hose holder 1
Front brake hose union bolt 2
Copper washers 3
4-38
FRONT BRAKE
EAS22410
ASSEMBLING THE FRONT BRAKE

CALIPERS
EWA13620
WARNING
Before installation, all internal brake components should be cleaned and lubricated
with clean or new brake fluid.
Never use solvents on internal brake components as they will cause the piston seals
to swell and distort.
Whenever a brake caliper is disassembled,
replace the brake caliper piston seals.
b. Remove the brake caliper piston seals.
EAS22390
CHECKING THE FRONT BRAKE CALIPERS
Recommended fluid
DOT 4
Recommended brake component replacement schedule

Brake pads
If necessary
Piston seals
Every two years
Brake hoses
Every four years
Brake fluid
Every two years and

whenever the brake
is disassembled
EAS22440
INSTALLING THE FRONT BRAKE CALIPERS

brake calipers.
1. Install:
Front brake caliper 1
(temporarily)
Copper washers New
Front brake hose 2
T.
1. Check:
Brake caliper pistons 1
Rust/scratches/wear Replace the brake
caliper pistons.
Brake caliper cylinders 2
Scratches/wear Replace the brake caliper
assembly.
Brake caliper body 3
Cracks/damage Replace the brake caliper
assembly.
Brake fluid delivery passages
(brake caliper body)
Obstruction Blow out with compressed air.
R.

32 Nm (3.2 mkg, 23 ftlb)
EWA13530
WARNING
Proper brake hose routing is essential to insure safe vehicle operation. Refer to CABLE
ROUTING on page 2-45.
ECA14170
CAUTION:
When installing the brake hose onto the

brake caliper 1, make sure the brake pipe
a touches the projection b on the brake
caliper.
EWA13600
WARNING

replace the piston seals.
a
1
2
b
4-39
FRONT BRAKE
LEVEL on page 3-20.
2. Remove:
Front brake caliper
3. Install:
Brake pads
Brake pad spring
Brake pad pin
Brake pad clips
Front brake caliper
Brake hose guide
T.
R.
Brake caliper bolt

40 Nm (4.0 mkg, 29 ftlb)
Brake hose holder bolt
10 Nm (1.0 mkg, 7.2 ftlb)
LOCTITE
7. Check:
Refer to REPLACING THE FRONT BRAKE

PADS on page 4-37.
4. Fill:
Brake master cylinder reservoir
(with the specified amount of the recommended brake fluid)
Recommended fluid
DOT 4
EAS22490
REMOVING THE FRONT BRAKE MASTER

CYLINDER
NOTE:
Before removing the front brake master cylinder,

drain the brake fluid from the entire brake system.
EWA13090
WARNING

brake performance.
1. Remove:
Copper washers 2
Front brake hose 3
NOTE:
To collect any remaining brake fluid, place a

container under the master cylinder and the end
of the brake hose.
ECA13540
CAUTION:

5. Bleed:
Brake system
6. Check:
Brake fluid level
EAS22500
CHECKING THE FRONT BRAKE MASTER

CYLINDER
1. Check:
Brake master cylinder 1
Damage/scratches/wear Replace.
4-40
FRONT BRAKE
(brake master cylinder body)
First, tighten the rear bolt, then the front bolt.
1
a
1
2. Install:
Copper washers New
Front brake hose 1
R.
ASSEMBLING THE FRONT BRAKE MASTER

CYLINDER
T.
2. Check:
3. Check:
Brake master cylinder reservoir diaphragm
4. Check:
Brake hose
EAS22520

30 Nm (3.0 mkg, 22 ftlb)
EWA13530
WARNING
NOTE:
Install the brake hose at a right angle to the

front brake master cylinder as shown in the illustration.
While holding the brake hose, tighten the union
bolt.
Turn the handlebar to the left and right to make
sure the brake hose does not touch other parts
(e.g., wire harness, cables, leads). Correct if
necessary.
EWA13520
WARNING
Recommended fluid
DOT 4
EAS22530
INSTALLING THE FRONT BRAKE MASTER

CYLINDER
1. Install:
Front brake master cylinder 1
Front brake master cylinder holder 2
1
1030
T.
R.

10 Nm (1.0 mkg, 7.2 ftlb)
3. Fill:
NOTE:
Align the end of the brake master cylinder holder with the punch mark a on the handlebar.
Recommended fluid
DOT 4
4-41
FRONT BRAKE
EWA13540
WARNING

brake performance.
not enter the brake master cylinder reservoir. Water will significantly lower the boiling point of the brake fluid and could cause
vapor lock.
ECA13540
CAUTION:

4. Bleed:
Brake system
5. Check:
Brake fluid level
LEVEL on page 3-20.
6. Check:
4-42
REAR BRAKE
EAS22550
REAR BRAKE
Removing the rear brake pads
T.
R.
6 Nm (0.6 m kg, 4.3 ft Ib)
3
4
2
LS
1
T.
R.
Order
27 Nm (2.7 m kg, 19 ft Ib)

Job/Parts to remove
Qty
Rear brake caliper
Rear brake pad
Brake pad spring
Remarks
4-43
REAR BRAKE
Removing the rear brake master cylinder
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
3
4
1
2
5
10
11
New
12
14
13
15
T.
R.
T.
T.
R.
R.
T.
R.
Order
48 Nm (4.8 m kg, 35 ft Ib)
7 8 New
23 Nm (2.3 m kg, 17 ft Ib)
LT
16 Nm (1.6 m kg, 11 ft Ib)
30 Nm (3.0 m kg, 22 ft Ib)
Job/Parts to remove
Qty
Remarks
Drain.
Brake fluid
1
Brake fluid reservoir cap
Brake fluid reservoir diaphragm holder
Brake fluid reservoir diaphragm
Brake fluid reservoir
Brake fluid reservoir hose
Rear brake master cylinder cover
Copper washer
Rear brake hose
10
11
Right rider footrest assembly
12
Brake rod
13
Locknut
14
Brake master cylinder bracket
4-44
REAR BRAKE
Removing the rear brake master cylinder
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
3
4
1
2
5
10
11
New
12
14
13
15
T.
R.
T.
R.
T.
R.
15
T.
R.
Order
48 Nm (4.8 m kg, 35 ft Ib)
7 8 New
23 Nm (2.3 m kg, 17 ft Ib)
LT
16 Nm (1.6 m kg, 11 ft Ib)
30 Nm (3.0 m kg, 22 ft Ib)
Job/Parts to remove
Qty
Brake master cylinder
Remarks
1
4-45
REAR BRAKE
Disassembling the rear brake master cylinder
1
2 New
4 New
3 New
Order
Job/Parts to remove
Qty
Dust boot
Circlip
Circlip
Brake hose joint
O-ring
Brake master cylinder body
Remarks
4-46
REAR BRAKE
Removing the rear brake caliper
5
LS
2 New
T.
T.
R.
Order
R.
30 Nm (3.0 m kg, 22 ft Ib)
27 Nm (2.7 m kg, 19 ft Ib)
Job/Parts to remove
Qty
Remarks
Drain.
Brake fluid
1
Copper washer
Rear brake hose
Rear brake caliper
1
4-47
REAR BRAKE
Disassembling the rear brake caliper
2 New
T.
R.
6 Nm (0.6 m kg, 4.3 ft Ib)
Order
Job/Parts to remove
Qty
Brake caliper piston seal
Bleed screw
Remarks
4-48
REAR BRAKE
EAS22560
INTRODUCTION

5.5 mm (0.22 in)
EWA14100
WARNING
5. Adjust:
DISCS on page 4-36.
T.
R.
Disc brake components rarely require disassembly. Therefore, always follow these preventive measures:
Never disassemble brake components unless absolutely necessary.
If any connection on the hydraulic brake
system is disconnected, the entire brake
system must be disassembled, drained,
cleaned, properly filled, and bled after reassembly.
Use only clean or new brake fluid for cleaning brake components.
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
Avoid brake fluid coming into contact with
the eyes as it can cause serious injury.
FIRST AID FOR BRAKE FLUID ENTERING
THE EYES:
Flush with water for 15 minutes and get immediate medical attention.
Brake disc bolt

18 Nm (1.8 mkg, 13 ftlb)
LOCTITE
6. Install:
Rear wheel
Refer to REAR WHEEL on page 4-23.
EAS22580
REPLACING THE REAR BRAKE PADS

NOTE:
When replacing the brake pads, it is not necessary to disconnect the brake hose or disassemble the brake caliper.
1. Measure:
Brake pad wear limit a
Out of specification Replace the brake
pads as a set.
5.8 mm (0.23 in)
Limit
0.8 mm (0.03 in)
5.8 mm (0.23 in)
Limit
0.8 mm (0.03 in)
EAS22570
CHECKING THE REAR BRAKE DISC

1. Remove:
Rear wheel
2. Check:
Brake disc
Damage/galling Replace.
3. Measure:
Out of specification Correct the brake disc
deflection or replace the brake disc.
DISCS on page 4-36.

0.15 mm (0.0059 in)
4. Measure:
Brake disc thickness
Measure the brake disc thickness at a few different locations.
DISCS on page 4-36.
2. Install:
Brake pads
Brake pad springs
4-49
REAR BRAKE
NOTE:
Always install new brake pads and brake pad

springs as a set.
EAS22590
REMOVING THE REAR BRAKE CALIPER
a. Connect a clear plastic hose 1 tightly to the

bleed screw 2. Put the other end of the hose
into an open container.
b. Loosen the bleed screw and push the brake
caliper piston into the brake caliper with your
finger.
NOTE:
Before disassembling the brake caliper, drain

the brake fluid from the entire brake system.
1. Remove:
Rear brake hose union bolt 1
Copper washers 2
Rear brake hose 3
NOTE:
Put the end of the brake hose into a container

and pump out the brake fluid carefully.
c. Tighten the bleed screw.
T.
R.

6 Nm (0.6 mkg, 4.3 ftlb)
3. Install:
Brake caliper
EAS22600
T.
R.
DISASSEMBLING THE REAR BRAKE

CALIPER
1. Remove:
Brake caliper piston seals

27 Nm (2.7 mkg, 19 ftlb)
4. Check:
Brake fluid level
LEVEL on page 3-20.
a. Blow compressed air into the brake hose joint

opening a to force out the piston from the
brake caliper.
EWA13550
WARNING
Cover the brake caliper piston with a rag.

Be careful not to get injured when the piston is expelled from the brake caliper.
Never try to pry out the brake caliper piston.
5. Check:
Brake pedal operation
4-50
REAR BRAKE
EAS22650
ASSEMBLING THE REAR BRAKE CALIPER

EWA13620
WARNING
Never use solvents on internal brake components as they will cause the piston seals
a
b. Remove the brake caliper piston seals.
Recommended fluid
DOT 4
EAS22640
CHECKING THE REAR BRAKE CALIPER

Recommended brake component replacement schedule
Brake pads
If necessary
Piston seals
Every two years
Brake hoses
Every four years
Brake fluid
Every two years and

whenever the brake
is disassembled
EAS22670
INSTALLING THE REAR BRAKE CALIPER

1. Install:
Rear brake caliper 1
(temporarily)
Copper washers New
Rear brake hose 2
T.
1. Check:
Brake caliper piston 1
Rust/scratches/wear Replace the brake
caliper piston.
Brake caliper cylinder 2
Scratches/wear Replace the brake caliper
assembly.
Brake caliper body 3
Cracks/damage Replace the brake caliper
assembly.
(brake caliper body)
R.

30 Nm (3.0 mkg, 22 ftlb)
EWA13530
WARNING
ECA14170
CAUTION:

brake caliper 1, make sure the brake pipe
a touches the projection b on the brake
caliper.
EWA13610
WARNING

3
1
1
3
2. Remove:
Rear brake caliper
3. Install:
Brake pads
4-51
REAR BRAKE
Brake pad springs
Rear brake caliper bolts
Rear brake caliper
Refer to REPLACING THE REAR BRAKE
PADS on page 4-49.
T.
R.

27 Nm (2.7 mkg, 19 ftlb)
4. Fill:
7. Check:
Recommended fluid
DOT 4
EWA13090
WARNING

brake performance.
EAS22700
REMOVING THE REAR BRAKE MASTER

CYLINDER
NOTE:
Before removing the rear brake master cylinder,

drain the brake fluid from the entire brake system.
1. Remove:
Copper washers 2
Rear brake hose 3
NOTE:
To collect any remaining brake fluid, place a

of the brake hose.
ECA13540
CAUTION:

5. Bleed:
Brake system
6. Check:
Brake fluid level
LEVEL on page 3-20.
EAS22720
CHECKING THE REAR BRAKE MASTER

CYLINDER
1. Check:
Brake master cylinder
(brake master cylinder body)
4-52
REAR BRAKE
2. Check:
3. Check:
Brake fluid reservoir diaphragm
4. Check:
Brake hoses
1 New
2. Fill:
EAS22730
ASSEMBLING THE REAR BRAKE MASTER

CYLINDER
EWA13520
Recommended fluid
DOT 4
WARNING
EWA13090
WARNING

brake performance.
Recommended fluid
DOT 4
EAS22740
INSTALLING THE REAR BRAKE MASTER

CYLINDER
1. Install:
Copper washers 1 New
Rear brake hose 2
ECA13540
CAUTION:
T.
R.

30 Nm (3.0 mkg, 22 ftlb)

EWA13530
WARNING
3. Bleed:
Brake system
4. Check:
Brake fluid level
LEVEL on page 3-20.
EC1D71009
CAUTION:

brake master cylinder, make sure the brake
pipe touches the projection a on the brake
caliper bracket as shown.
4-53
REAR BRAKE
5. Check:
6. Adjust:
Refer to ADJUSTING THE REAR DISC
BRAKE on page 3-20.
7. Adjust:
Refer to ADJUSTING THE REAR BRAKE
LIGHT SWITCH on page 3-22.
4-54
HANDLEBAR
EAS22840
HANDLEBAR
Removing the handlebar
T.
R.
28 Nm (2.8 m kg, 20 ft Ib)
LS
13
7
16
17
10
4
3
14
LS
7
T.
23 Nm (2.3 m kg, 17 ft Ib)
R.
19
11
15
14
LT
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
12
T.
R.
50 Nm (5.0 m kg, 36 ft Ib)
18
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
Order
32 Nm (3.2 m kg, 23 ft Ib)
Job/Parts to remove
Qty
Remarks
4-1.
Headlight body
1
Rearview mirror
Plastic clamp
Front brake light switch connector
Front brake master cylinder holder
Front brake master cylinder assembly
Throttle cable holder
Right handlebar switch
Throttle cable
Grip end
10
Throttle grip
11
Clutch switch coupler
12
Clutch master cylinder holder
13
Clutch master cylinder assembly
14
Left handlebar switch
4-55
Disconnect.
Disconnect.
HANDLEBAR
Removing the handlebar
T.
R.
28 Nm (2.8 m kg, 20 ft Ib)
LS
13
7
16
17
10
4
3
14
LS
7
T.
23 Nm (2.3 m kg, 17 ft Ib)
R.
19
11
15
14
LT
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
12
T.
R.
50 Nm (5.0 m kg, 36 ft Ib)
18
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
Order
15
32 Nm (3.2 m kg, 23 ft Ib)
Job/Parts to remove
Qty
Handlebar grip
Remarks
16
Upper handlebar holder
17
Handlebar
18
Hose guide
19
Lower handlebar holder
1
4-56
HANDLEBAR
EAS22860
REMOVING THE HANDLEBAR

EWA13120
WARNING

2. Remove:
Handlebar grip 1
NOTE:
3. Pass the left and right handlebar switch leads

through the handlebar.
4. Install:
Handlebar 1
Upper handlebar holder 2
Blow compressed air between the handlebar

and the left handlebar grip, and gradually push
the grip off the handlebar.
T.
Upper handlebar holder bolt

28 Nm (2.8 mkg, 20 ftlb)
R.
ECA14250
CAUTION:
First, tighten the bolts on the front side of

the handlebar holder, and then on the rear
side.
Turn the handlebar all the way to the left
and right. If there is any contact with the
fuel tank, adjust the handlebar position.
EAS22880
CHECKING THE HANDLEBAR

1. Check:
Handlebar
Bends/cracks/damage Replace.
NOTE:
Align the match marks a on the handlebar with

the upper surface of the lower handlebar holders.
EWA13690
WARNING
Do not attempt to straighten a bent handlebar as this may dangerously weaken it.
EAS22930
INSTALLING THE HANDLEBAR

EWA13120
WARNING

a
1
2. Connect:
Throttle cable (decelerator cable) 1
(to the right handlebar switch 2)
5. Install:
Handlebar grip
NOTE:
a. Apply a thin coat of rubber adhesive onto the

left end of the handlebar.
b. Slide the handlebar grip over the left end of
the handlebar.
c. Wipe off any excess rubber adhesive with a
clean rag.
Rotate the right handlebar switch and screw it

onto the end of the throttle cable.
4-57
HANDLEBAR
There should be 13 mm (0.040.12 in) of
clearance c between the throttle grip and the
grip end.
EWA13700
WARNING
Do not touch the handlebar grip until the rubber adhesive has fully dried.
6. Install:
Left handlebar switch 1
NOTE:
Align the projection a on the left handlebar

switch with the hole b in the handlebar.
a
1
a
7. Install:
Clutch master cylinder 1
Clutch master cylinder holder 2
T.
9. Install:
Front brake master cylinder 1
Front brake master cylinder holder 2
R.

bolt
10 Nm (1.0 mkg, 7.2 ftlb)
T.
R.
NOTE:
Align the end of the clutch master cylinder

holder with the punch mark a on the handlebar.
First tighten the rear bolt, then the front bolt.

10 Nm (1.0 mkg, 7.2 ftlb)
NOTE:
Align the end of the front brake master cylinder

holder with the punch mark a on the handlebar.
First tighten the rear bolt, then the front bolt.
a
2
8. Install:
Throttle grip
Throttle cables
Right handlebar switch 1
Grip end 2
2
a
10.Adjust:
Refer to ADJUSTING THE THROTTLE CABLE FREE PLAY on page 3-8.
NOTE:
Align the projection a on the right handlebar

switch with the hole b in the handlebar.
4-58
HANDLEBAR
4.06.0 mm (0.160.24 in)
4-59
FRONT FORK
EAS22950
FRONT FORK
Removing the front fork legs
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
115 Nm (11.5 m kg, 85 ft lb)

T.
R.
19 Nm (1.9 m kg, 13 ft Ib)

T.
R.
7
9
16 Nm (1.6 m kg, 11 ft Ib)
LT
4
8
1
2
10
11
5
LT
LT
3
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
12
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
Order
Job/Parts to remove
Qty
Remarks
the front fork legs.
Windshield bracket (left and right)
For XV19CTSV(C)/XV19CTV(C)/
XV19CTMV(C) only
Refer to HANDLEBAR on page 4-55.
Front fender
Upper bracket cover
Loosen.
Cap bolt
Loosen.
Steering stem nut
Upper bracket
Upper front fork cover
Upper front fork cover spacer
Upper front fork cover washer
Lower front fork cover nut
10
11
Lower front fork cover
4-60
Loosen.
FRONT FORK
Removing the front fork legs
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
115 Nm (11.5 m kg, 85 ft lb)

T.
R.
19 Nm (1.9 m kg, 13 ft Ib)

T.
R.
7
9
16 Nm (1.6 m kg, 11 ft Ib)
LT
4
8
1
2
10
11
5
LT
LT
3
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
12
T.
R.
Order
12
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Front fork leg
Remarks
1
4-61
FRONT FORK
Disassembling the front fork legs
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
1
New 2
3
12
6 New
7 New
13 New
14
15 New
16 New
10
19
17
18
11
9 New
8
LT
T.
R.
Order
Job/Parts to remove
40 Nm (4.0 m kg, 29 ft Ib)
Qty
Remarks
the front fork legs.
Cap bolt
O-ring
Spacer
Spring seat
Fork spring
Dust seal
Oil seal clip
Damper rod bolt
Copper washer
10
Damper rod
11
Rebound spring
12
Inner tube
13
Oil seal
14
Washer
15
Outer tube bushing
16
Inner tube bushing
4-62
FRONT FORK
Disassembling the front fork legs
T.
R.
23 Nm (2.3 m kg, 17 ft Ib)
1
New 2
3
12
6 New
7 New
13 New
14
15 New
16 New
10
19
17
18
11
9 New
8
LT
T.
R.
Order
Job/Parts to remove
40 Nm (4.0 m kg, 29 ft Ib)
Qty
17
Spring
18
Oil flow stopper
19
Outer tube
Remarks
4-63
FRONT FORK
EAS22960
REMOVING THE FRONT FORK LEGS

front fork legs.
EWA13120
WARNING

NOTE:
3. Remove:
Damper rod bolt 1
Copper washer

2. Loosen:
Lower bracket pinch bolts
NOTE:
While holding the damper rod with the damper

rod holder 2 and T-handle 3, loosen the
damper rod bolt.
EW1D71007
WARNING
Before loosening the lower bracket pinch

bolts, support the front fork leg.
Damper rod holder

90890-01460
T-handle
90890-01326
YM-01326
EAS22980
DISASSEMBLING THE FRONT FORK LEGS

front fork legs.
1. Drain:
Fork oil
NOTE:
Stroke the outer tube several times while draining the fork oil.
4. Remove:
Inner tube
a. Hold the front fork leg horizontally.

b. Securely clamp the brake caliper bracket in a
vise with soft jaws.
c. Separate the inner tube from the outer tube
by pulling the inner tube forcefully but carefully.
2. Remove:
Dust seal 1
Oil seal clip 2
(with a flathead screwdriver)
ECA14180
CAUTION:
ECA14190
CAUTION:
Do not scratch the inner tube.
Excessive force will damage the oil seal

and bushing. A damaged oil seal or bushing must be replaced.
Avoid bottoming the inner tube into the outer tube during the above procedure, as the
oil flow stopper will be damaged.
4-64
FRONT FORK
ECA14200
CAUTION:
The front fork leg has a built-in damper adjusting rod and a very sophisticated internal construction, which are particularly
sensitive to foreign material.
When disassembling and assembling the
front fork leg, do not allow any foreign material to enter the front fork.
4. Check:
Cap bolt O-ring
EAS23010
CHECKING THE FRONT FORK LEGS

front fork legs.
1. Check:
Inner tube
Outer tube
Bends/damage/scratches Replace.
EAS23020
ASSEMBLING THE FRONT FORK LEGS

front fork legs.
EWA13660
WARNING
Make sure the oil levels in both front fork

legs are equal.
Uneven oil levels can result in poor handling and a loss of stability.
EWA13650
WARNING
Do not attempt to straighten a bent inner

tube as this may dangerously weaken it.
2. Measure:
Spring free length a
NOTE:
When assembling the front fork leg, be sure to

replace the following parts:
Inner tube bushing
Outer tube bushing
Oil seal
Dust seal
Before assembling the front fork leg, make
sure all of the components are clean.
Fork spring free length

273.9 mm (10.78 in)
Limit
268.4 mm (10.57 in)
1. Install:
Inner tube bushing 1
Damper rod 2
Rebound spring
Spring 3
Oil flow stopper 4
EC1D71012
CAUTION:
Allow the damper rod to slide slowly down

the inner tube 5 until it protrudes from the
bottom of the inner tube. Be careful not to
damage the inner tube.
3. Check:
Damper rod
Obstruction Blow out all of the oil passages with compressed air.
Oil flow stopper
Damage Replace.
4-65
FRONT FORK
Washer
(with the fork seal driver 2)
Fork seal driver
90890-01442
Adjustable fork seal driver (3646
mm)
YM-01442
3
4
5
1
2
2. Lubricate:
Inner tubes outer surface
Recommended oil
Fork oil 10WT
3. Install:
Inner tube
(in the outer tube)
4. Install:
7. Install:
Oil seal 1
(with the fork seal driver 2)
Copper washer New

Damper rod bolt
5. Tighten:
Damper rod bolt 1
T.
R.
Damper rod bolt

40 Nm (4.0 mkg, 29 ftlb)
LOCTITE
ECA14220
CAUTION:
Make sure the numbered side of the oil seal

faces up.
NOTE:
Before installing the oil seal, lubricate its lips

with lithium-soap-based grease.
Lubricate the outer surface of the inner tube
with fork oil.
Before installing the oil seal, cover the top of
the front fork leg with a plastic bag to protect
the oil seal during installation.
NOTE:
While holding the damper rod assembly with the

damper rod holder 2 and T-handle 3, tighten
the damper rod bolt.
Damper rod holder
90890-01460
T-handle
90890-01326
YM-01326
6. Install:
Outer tube bushing 1
4-66
FRONT FORK
Quantity
571.0 cm (19.31 US oz) (20.10
Imp.oz)
Recommended oil
Fork oil 10WT
2
11.Measure:
Front fork leg oil level a
(from the top of the inner tube, with the outer
tube fully compressed and without the fork
spring)
Out of specification Correct.
8. Install:
Oil seal clip 1
NOTE:
Level
124.0 mm (4.88 in)
Adjust the oil seal clip so that it fits into the outer
tubes groove.
NOTE:
While filling the front fork leg, keep it upright.

After filling, slowly pump the front fork leg up
and down to distribute the fork oil.
9. Install:
Dust seal 1
(with the fork seal driver weight 2)
Fork seal driver
90890-01442
Adjustable fork seal driver (3646
mm)
YM-01442
12.Install:
Spring 1
Spring seat 2
Spacer
Cap bolt
(with O-ring)
NOTE:
Install the spring with the smaller pitch facing

up.
Before installing the cap bolt, lubricate its Oring with grease.
Temporarily tighten the cap bolt.
10.Fill:
Front fork leg
(with the specified amount of the recommended fork oil)
4-67
FRONT FORK
NOTE:
Align the groove a in the upper front fork cover

1 with the lower front fork cover nut 2.
EAS23050
INSTALLING THE FRONT FORK LEGS

front fork legs.
1. Install:
Lower front fork cover 1
Front fork leg 2
Upper bracket 3
Temporarily tighten the lower bracket pinch
bolts and steering stem nut.
6. Tighten:
Steering stem nut
T.
R.
Steering stem nut

115 Nm (11.5 mkg, 85 ftlb)
Cap bolt
NOTE:
T.
Make sure the inner tube end is flush with the top
of the upper bracket.
R.
Cap bolt
23 Nm (2.3 mkg, 17 ftlb)
Upper bracket pinch bolts
3
T.
R.

10 Nm (1.0 mkg, 7.2 ftlb)
LOCTITE
2
1
NOTE:
Tighten the upper bracket pinch bolts to specification twice. Tighten the upper and lower bolts
alternately, starting with the upper bolts.
Upper bracket cover bolts
2. Tighten:
Lower bracket pinch bolts
T.
R.
T.
R.

23 Nm (2.3 mkg, 17 ftlb)
3. Remove:
Upper bracket
4. Tighten:
Lower front fork cover nuts

19 Nm (1.9 mkg, 13 ftlb)
LOCTITE
Upper bracket cover bolts
T.
R.
T.
R.
Lower front fork cover nut

7 Nm (0.7 mkg, 5.1 ftlb)

16 Nm (1.6 mkg, 11 ftlb)
LOCTITE
EWA13680
WARNING
5. Install:
Upper front fork cover 1
Upper bracket
Make sure the brake hoses are routed properly.
4-68
STEERING HEAD
EAS23090
STEERING HEAD
Removing the lower bracket
T.
T.
R.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LS
1st 52 Nm (5.2 m kg, 37 ft lb)

2nd 18 Nm (1.8 m kg, 13 ft Ib)
4
5
6
7
LS
LT
9
10
13
T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
13
11
LT
12
LS
LT
T.
R.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Remarks
Refer to HANDLEBAR on page 4-55.
Upper bracket/Front fork legs
Headlight bracket and throttle cable guide
Front brake hose guide
Front brake hose joint
Lock washer
Upper ring nut
Rubber washer
Lower ring nut
Lower bracket
Upper bearing cover
10
Upper bearing
11
Lower bearing
12
Dust seal
4-69
STEERING HEAD
Removing the lower bracket
T.
T.
R.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LS
1st 52 Nm (5.2 m kg, 37 ft lb)

2nd 18 Nm (1.8 m kg, 13 ft Ib)
4
5
6
7
LS
LT
9
10
13
T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
13
11
LT
12
LS
LT
T.
R.
Order
13
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Bearing outer race
Remarks
2
4-70
STEERING HEAD
EAS23110
REMOVING THE LOWER BRACKET

a. Remove the bearing races from the steering

head pipe with a long rod 1 and hammer.
b. Remove the bearing race from the lower
bracket with a floor chisel 2 and hammer.
c. Install a new dust seal and new bearing races.
EWA13120
WARNING

ECA14270
2. Remove:
Upper ring nut
Rubber washer
Lower ring nut 1
Lower bracket
CAUTION:
If the bearing race is not installed properly,

the steering head pipe could be damaged.
NOTE:
EWA13730
Always replace the bearings and bearing races

as a set.
Whenever the steering head is disassembled,
replace the dust seal.
WARNING
Securely support the lower bracket so that

there is no danger of it falling.
NOTE:
Remove the lower ring nut with the steering nut

wrench 2.
Steering nut wrench
90890-01403
Spanner wrench
YU-33975
EAS23120
CHECKING THE STEERING HEAD

1. Wash:
Bearings
Bearing races
4. Check:
Upper bracket
Lower bracket
(along with the steering stem)
Recommended cleaning solvent

Kerosene
2. Check:
Bearings
Bearing races
Damage/pitting Replace.
3. Replace:
Bearings
Bearing races
EAS23140
INSTALLING THE STEERING HEAD

1. Lubricate:
Upper bearing
Lower bearing
Bearing races
4-71
STEERING HEAD
2. Install:
Lower ring nut 1
Rubber washer 2
Upper ring nut 3
Lock washer 4
Refer to CHECKING AND ADJUSTING
THE STEERING HEAD on page 3-25.
3. Install:
Front brake hose joint 1
Front brake hose guide 2
NOTE:
Make sure that the projection a on the lower

bracket contacts the side b of the front brake
hose joint 1.
Align the projection c on the front brake hose
guide with the hole d in the lower bracket.
d c
b
4. Install:
Front fork legs
Upper bracket
4-72
REAR SHOCK ABSORBER ASSEMBLY AND SWINGARM

ET1D71001

Removing the rear shock absorber assembly and swingarm
T.
48 Nm (4.8 m kg, 35 ft Ib)
R.
4
T.
LS
R.
LT
7 Nm (0.7 m kg, 5.1 ft Ib)
5
5
6
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
R.
125 Nm (12.5 m kg, 90 ft lb)
LT
T.
R.
48 Nm (4.8 m kg, 35 ft Ib)
5
T.
R.
Order
59 Nm (5.9 m kg, 43 ft Ib)
Job/Parts to remove
Qty
Rear wheel
Remarks
Exhaust pipes
Brake master cylinder bracket
Engine mounting nut (rear lower side)
Loosen.
Horn 1 coupler
Horn 1
Passenger footrest (left and right)
Rear brake hose guide
Self-locking nut/Bolt/Spacer/Washer
Pivot shaft nut/Washer
Pivot shaft
Rear shock absorber and swingarm assembly
Lower drive belt cover
Disconnect.
For XV19SV(C)/XV19V(C)/XV19MV(C) only
1/1/1/1
1/1
4-73

Removing the rear shock absorber and swingarm
LS
3
New
2
LS
T.
40 Nm (4.0 m kg, 29 ft Ib)
R.
2
LS
13
12
1
LS
12
6
14
5
8
9
14
LS
13
11
New
14
LS
LS
10
14
LS
T.
R.
59 Nm (5.9 m kg, 43 ft Ib)
4
T.
R.
59 Nm (5.9 m kg, 43 ft Ib)
LS
Order
Job/Parts to remove
Qty
Self-locking nut/Washer/Bolt
Oil seal/Collar/Bushing/Bearing
Swingarm
Connecting arm
O-ring
Spacer
Bushing
Remarks
1/2/1
2/2/1/2
1
1/1/1
1/2/1
10
Rear shock absorber
11
Relay arm
12
Oil seal/Spacer/Bearing
2/1/1
13
Oil seal/Spacer/Bearing
2/1/2
14
Collar/Oil seal/Spacer/Bearing
2/2/1/2
4-74

EAS23180
HANDLING THE REAR SHOCK ABSORBER
NOTE:

EWA13740
WARNING
This rear shock absorber contains highly

compressed nitrogen gas. Before handling
the rear shock absorber, read and make sure
you understand the following information.
The manufacturer cannot be held responsible for property damage or personal injury
that may result from improper handling of
the rear shock absorber.
Do not tamper or attempt to open the rear
shock absorber.
Do not subject the rear shock absorber to
an open flame or any other source of high
heat. High heat can cause an explosion due
to excessive gas pressure.
Do not deform or damage the rear shock
absorber in any way. Rear shock absorber
damage will result in poor damping performance.
2. Loosen:
NOTE:
Because there is force being exerted on the engine mounting bracket (left and right rear lower
sides), it is necessary to loosen the engine
mounting nut (rear lower side) in order to create
some space between the connecting arms and
engine bracket before removing the rear shock
absorber and swingarm.
3. Remove:
Connecting arm bolt (frame side)
NOTE:
When removing the connecting arm bolt (frame

side), hold the swingarm so that it does not drop
down.
4. Measure:
Swingarm side play
Swingarm vertical movement
EAS23190
DISPOSING OF A REAR SHOCK ABSORBER

1. Gas pressure must be released before disposing of a rear shock absorber. To release
the gas pressure, drill a 23 mm (0.080.12
in) hole through the rear shock absorber at a
point 1520 mm (0.590.79 in) from its end
as shown.
a. Measure the tightening torque of the pivot

shaft nut.
T.
R.
EWA13760
WARNING
Pivot shaft nut

125 Nm (12.5 mkg, 90 ftlb)
b. Measure the swingarm side play A by moving the swingarm from side to side.
c. If the swingarm side play is out of specification, check the spacers, bearings, washers,
and oil seals.
Wear eye protection to prevent eye damage

from released gas or metal chips.
Swingarm side play (at the end of

the swingarm)
1.0 mm (0.04 in)
d. Check the swingarm vertical movement B
by moving the swingarm up and down.
If swingarm vertical movement is not smooth
or if there is binding, check the spacers, bearings, washers, and oil seals.
ET1D71002
REMOVING THE REAR SHOCK ABSORBER

ASSEMBLY AND SWINGARM
EWA13120
WARNING

4-75

EAS23360
CHECKING THE SWINGARM

1. Check:
Swingarm
2. Check:
Pivot shaft
Roll the pivot shaft on a flat surface.
Bends Replace.
EWA13770
WARNING
Do not attempt to straighten a bent pivot

shaft.
EAS23240
CHECKING THE REAR SHOCK ABSORBER

ASSEMBLY
1. Check:
Rear shock absorber rod
Bends/damage Replace the rear shock
absorber assembly.
Rear shock absorber
Gas leaks/oil leaks Replace the rear shock
absorber assembly.
Spring
Damage/wear Replace the rear shock absorber assembly.
Bushing
Damage/wear Replace the rear shock absorber assembly.
Spacer
Bolts
Bends/damage/wear Replace.
3. Wash:
Pivot shaft
Bushing
Washer
Bearings
Collars
Recommended cleaning solvent
Kerosene
EAS23260
4. Check:
Washer
Oil seals
Bushing
Bearings
Collar
CHECKING THE CONNECTING ARM AND

RELAY ARM
1. Check:
Connecting arms
Relay arm
2. Check:
Bearings
Oil seals
3. Check:
Bushings
4. Check:
Spacers
Collars
ET1D71003
INSTALLING THE RELAY ARM, REAR

SHOCK ABSORBER ASSEMBLY AND
CONNECTING ARMS
1. Lubricate:
Oil seals
4-76

2. Install:
Bearings 1, 2, 3
(to the relay arm)
Oil seals 4, 5
(to the relay arm)
Spacer 2
EC1D71010
CAUTION:
When inserting the spacer into the connecting arms and the rear shock absorber, be
careful not to damage the bushings and Orings.
Installed depth a
4.5 mm (0.18 in)
Installed depth b
1.0 mm (0.04 in)
Installed depth c
6.0 mm (0.24 in)
Installed depth d
2.5 mm (0.10 in)
NOTE:
Install the bushings so that the slits b in the

bushings are within the areas shown in the illustration.
Installed depth a
4.5 mm (0.18 in)
a
1
4
5
B
4
a
a
C
c
d
c
3
b
C
A. Right side
B. Left side
3.
4.
A.
B.
C.
3. Lubricate:
Bushings
Oil seals
O-rings
Collar
5. Install:
Connecting arms
(to relay arm)
Relay arm
(to the swingarm)
NOTE:
Apply grease only to the collar between the connecting arms and rear shock absorber.
Connecting arm
Rear shock absorber
Right side
Left side
90
NOTE:
Be sure to face the FWD mark a on the relay

arm 1 toward the front of the vehicle and to
face the label b on the rear shock absorber 2
downward.
4. Install:
Bushings 1
(to connecting arms)
4-77
2
a
a
6. Tighten:
Connecting-arm-to-relay-arm nut
2. Swingarm
A. Left side
B. Right side
T.
R.
Connecting-arm-to-relay-arm nut
59 Nm (5.9 mkg, 43 ftlb)
3. Install:
Pivot shaft
Washer
Pivot shaft nut
Rear-shock-absorber-assembly-to-relay-arm
nut
T.
R.
Rear-shock-absorber-assemblyto-relay-arm nut
40 Nm (4.0 mkg, 29 ftlb)
Relay-arm-to-swingarm nut
NOTE:
Temporarily tighten the pivot shaft nut.

4. Install:
Connecting arm bolt (front side)
NOTE:
T.
R.
When installing the connecting arm bolt, hold the

swingarm so that it does not drop down.
Relay-arm-to-swingarm nut
59 Nm (5.9 mkg, 43 ftlb)
5. Tighten:
Pivot shaft nut
Connecting arm nut (front side)
EAS28780
T.
INSTALLING THE SWINGARM

1. Lubricate:
Bearings
Collars
Oil seals
Pivot shaft
R.
2. Install:
Bearings 1
(to swingarm)
Pivot shaft nut

125 Nm (12.5 mkg, 90 ftlb)
side)
98 Nm (9.8 mkg, 71 ftlb)
Connecting arm nut (front side)
59 Nm (5.9 mkg, 43 ftlb)
6. Adjust:
Drive belt slack
SLACK on page 3-24.
Installed depth a
1.0 mm (0.04 in)
4-78
BELT DRIVE
EAS23510
BELT DRIVE
Removing the drive belt and drive pulley
T.
R.
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
63 Nm (6.3 m kg, 45 ft Ib)
10
T.
13
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
(3)
7
8
LT
LT
LT
7
12
(3)
New 11
T.
R.
140 Nm (14.0 m kg, 100 ft lb)
(4)
T.
R.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
(6)
Qty
Remarks
Rear wheel
Rear shock absorber assembly and swingarm
Refer to REAR SHOCK ABSORBER ASSEMBLY AND SWINGARM on page 4-73.
Rectifier/regulator cover
Lead cover
Stator coil coupler
Disconnect.
Rectifier/regulator coupler
Disconnect.
Rectifier/regulator
Drive pulley cover
Slider
Dowel pin
Transfer gear case bracket
10
Drive belt
11
Drive pulley nut
12
Conical spring washer
4-79
BELT DRIVE
Removing the drive belt and drive pulley
T.
R.
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
63 Nm (6.3 m kg, 45 ft Ib)
10
T.
13
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
(3)
7
8
LT
LT
LT
7
12
(3)
New 11
T.
R.
140 Nm (14.0 m kg, 100 ft lb)
(4)
T.
R.
Order
13
Qty
Drive pulley
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
(6)
Remarks
1
4-80
BELT DRIVE
The drive belt can not be bent smaller than
127 mm (5 in) a.
The removed drive belt can not be twisted
inside out.
EAS23520
REMOVING THE DRIVE BELT AND DRIVE

PULLEY
NOTE:
Loosen the drive pulley nut before removing the

rear wheel.
1. Loosen:
Drive pulley nut 1
NOTE:
When loosening the drive pulley nut, press down

on the brake pedal so the drive pulley does not
move.
3. Check:
Drive pulley
Rear wheel pulley
Bent teeth Replace the drive belt and pulleys as a set.
EAS23540
INSTALLING THE DRIVE BELT AND DRIVE

PULLEY
1. Install:
Drive pulley 1
Conical spring washer 2
EAS23530
CHECKING THE DRIVE BELT

1. Clean:
Drive belt
Drive pulley nut 3 New

NOTE:
a. Wipe the drive belt with a clean cloth.

b. Put the drive belt in a mixture of mild detergent and water. Then, remove any dirt from
the drive belt.
c. Remove the drive belt from the mixture and
rinse it off with clean water. Then, let the drive
belt thoroughly dry.
Install the conical spring washer 2 with the

OUT mark a facing out.
OUT
1
3 New
2. Install:
Drive belt
ECA14710
CAUTION:
Install the drive belt facing the same way it

was removed.
Do not twist the drive belt when installing it.
2. Check:
Drive belt
ECA14690
CAUTION:
To protect the drive belt from damage, handle it with care.
4-81
BELT DRIVE
3. Install:
Swingarm
Rear shock absorber
Refer to REAR SHOCK ABSORBER ASSEMBLY AND SWINGARM on page 4-73.
Rear wheel
4. Tighten:
Drive pulley nut
T.
R.
Drive pulley nut

140 Nm (14.0 mkg, 100 ftlb)
NOTE:
When tightening the drive pulley nut, press

down on the brake pedal so the drive pulley
does not move.
Stake the drive pulley nut 1 at a cutout a in
the middle driven shaft.
5. Adjust:
Drive belt slack
SLACK on page 3-24.
4-82
ENGINE
ENGINE REMOVAL ........................................................................................ 5-1
INSTALLING THE SHIFT PEDAL ASSEMBLY......................................... 5-5
CHECKING THE OIL COOLER ................................................................ 5-7
REMOVING THE ENGINE...................................................................... 5-12
INSTALLING THE ENGINE .................................................................... 5-12
CAMSHAFTS ................................................................................................ 5-14
REMOVING THE CYLINDER HEAD COVERS ...................................... 5-21
REMOVING THE ROCKER ARMS, PUSH RODS AND VALVE
LIFTERS................................................................................................. 5-21
REMOVING THE CAMSHAFTS ............................................................. 5-21
CHECKING THE CAMSHAFTS .............................................................. 5-23
CHECKING THE ROCKER ARMS AND ROCKER ARM SHAFTS ........ 5-24
CHECKING THE ROCKER ARM BASES............................................... 5-25
CHECKING THE PUSH RODS............................................................... 5-25
CHECKING THE VALVE LIFTERS AND VALVE LIFTER CASES ......... 5-25
CHECKING THE PUSH ROD COVER ................................................... 5-26
CHECKING THE DECOMPRESSION SYSTEM .................................... 5-26
CHECKING THE DECOMPRESSION CAM SPRING ............................ 5-26
CHECKING THE OIL DELIVERY PIPE .................................................. 5-27
INSTALLING THE CAMSHAFTS ............................................................ 5-27
BLEEDING A VALVE LIFTER................................................................. 5-29
INSTALLING THE VALVE LIFTERS....................................................... 5-30
INSTALLING THE ROCKER ARMS AND PUSH RODS ........................ 5-31
INSTALLING THE CYLINDER HEAD COVERS..................................... 5-32
INSTALLING THE SHIFT PEDAL ASSEMBLY....................................... 5-32
CYLINDER HEADS....................................................................................... 5-33
REMOVING THE CYLINDER HEADS .................................................... 5-35
CHECKING THE CYLINDER HEADS..................................................... 5-35
CHECKING THE OIL PIPE ..................................................................... 5-35
INSTALLING THE CYLINDER HEADS................................................... 5-36
VALVES AND VALVE SPRINGS ................................................................. 5-38
REMOVING THE VALVES ..................................................................... 5-39
CHECKING THE VALVES AND VALVE GUIDES .................................. 5-39
CHECKING THE VALVE SEATS............................................................ 5-41
CHECKING THE VALVE SPRINGS ....................................................... 5-42
INSTALLING THE VALVES .................................................................... 5-43
CYLINDERS AND PISTONS ........................................................................ 5-45
REMOVING THE PISTON ...................................................................... 5-46
CHECKING THE CYLINDERS AND PISTONS ...................................... 5-46
CHECKING THE PISTON RINGS .......................................................... 5-47
CHECKING THE PISTON PINS ............................................................. 5-48
INSTALLING THE PISTONS AND CYLINDERS .................................... 5-48
CLUTCH ........................................................................................................ 5-50

REMOVING THE CLUTCH ..................................................................... 5-60
REMOVING THE PRIMARY DRIVE GEAR ............................................ 5-60
REMOVING THE LEFT BALANCER DRIVE GEAR ............................... 5-60
CHECKING THE FRICTION PLATES .................................................... 5-61
CHECKING THE CLUTCH PLATES....................................................... 5-61
CHECKING THE CLUTCH SPRING PLATE .......................................... 5-61
CHECKING THE CLUTCH HOUSING.................................................... 5-62
CHECKING THE CLUTCH BOSS........................................................... 5-62
CHECKING THE PRESSURE PLATE .................................................... 5-62
CHECKING THE CLUTCH PUSH RODS ............................................... 5-62
CHECKING THE PRIMARY DRIVE GEAR............................................. 5-62
CHECKING THE PRIMARY DRIVEN GEAR .......................................... 5-62
CHECKING THE LEFT BALANCER GEARS ......................................... 5-62
INSTALLING THE LEFT BALANCER DRIVE GEAR.............................. 5-63
INSTALLING THE PRIMARY DRIVE GEAR........................................... 5-64
INSTALLING THE CLUTCH.................................................................... 5-64
DISASSEMBLING THE CLUTCH MASTER CYLINDER ........................ 5-66
CHECKING THE CLUTCH MASTER CYLINDER .................................. 5-66
ASSEMBLING THE CLUTCH MASTER CYLINDER .............................. 5-66
INSTALLING THE CLUTCH MASTER CYLINDER ................................ 5-67
REMOVING THE CLUTCH RELEASE CYLINDER ................................ 5-68
CHECKING THE CLUTCH RELEASE CYLINDER................................. 5-68
ASSEMBLING THE CLUTCH RELEASE CYLINDER ............................ 5-68
INSTALLING THE CLUTCH RELEASE CYLINDER............................... 5-68
SHIFT SHAFT ............................................................................................... 5-70
CHECKING THE SHIFT SHAFT ............................................................. 5-71
CHECKING THE STOPPER LEVER ...................................................... 5-71
INSTALLING THE SHIFT SHAFT ........................................................... 5-71
GENERATOR AND STARTER CLUTCH ..................................................... 5-72
REMOVING THE GENERATOR............................................................. 5-74
REMOVING THE STARTER CLUTCH ................................................... 5-74
CHECKING THE STARTER CLUTCH.................................................... 5-74
CHECKING THE TORQUE LIMITER...................................................... 5-75
INSTALLING THE STARTER CLUTCH.................................................. 5-75
INSTALLING THE GENERATOR ........................................................... 5-75
ELECTRIC STARTER................................................................................... 5-77
CHECKING THE STARTER MOTOR ..................................................... 5-79
ASSEMBLING THE STARTER MOTOR................................................. 5-80
TRANSFER GEAR CASE............................................................................. 5-81
REMOVING THE MIDDLE DRIVEN SHAFT........................................... 5-86
CHECKING THE MIDDLE DRIVE........................................................... 5-86
CHECKING THE OIL STRAINER ........................................................... 5-86
CHECKING THE TRANSFER GEAR OIL PUMP ................................... 5-86
CHECKING THE OIL PIPES................................................................... 5-87
ASSEMBLING THE TRANSFER GEAR OIL PUMP ............................... 5-87
INSTALLING THE TRANSFER GEAR CASE......................................... 5-87
CRANKCASE................................................................................................ 5-89
DISASSEMBLING THE CRANKCASE ................................................... 5-92
CHECKING THE CRANKCASE.............................................................. 5-92
CHECKING THE BEARINGS AND OIL SEAL ........................................ 5-92
CHECKING THE OIL DELIVERY PIPE AND OIL PIPE.......................... 5-92
CHECKING THE OIL STRAINERS......................................................... 5-92
CHECKING THE ENGINE OIL PUMP DRIVEN GEAR .......................... 5-93
INSTALLING THE BEARING RETAINERS ............................................ 5-93
ASSEMBLING THE CRANKCASE ......................................................... 5-93
OIL PUMP ..................................................................................................... 5-95
CHECKING THE OIL PUMP ................................................................... 5-98
CHECKING THE RELIEF VALVE ........................................................... 5-98
CHECKING THE BALL SPRING AND RELIEF VALVE SPRING ........... 5-98
CHECKING THE OIL STRAINER ........................................................... 5-99
ASSEMBLING THE OIL PUMP .............................................................. 5-99
INSTALLING THE OIL PUMP ............................................................... 5-100
CRANKSHAFT............................................................................................ 5-101
REMOVING THE CONNECTING RODS .............................................. 5-102
CHECKING THE CRANKSHAFT AND CONNECTING RODS............. 5-102
INSTALLING THE CONNECTING RODS............................................. 5-105
INSTALLING THE CRANKSHAFT ASSEMBLY ................................... 5-106
TRANSMISSION ......................................................................................... 5-107
CHECKING THE SHIFT FORKS .......................................................... 5-111
CHECKING THE SHIFT DRUM ASSEMBLY........................................ 5-111
CHECKING THE TRANSMISSION....................................................... 5-111
ASSEMBLING THE MAIN AXLE AND DRIVE AXLE............................ 5-112
INSTALLING THE SHIFT FORKS AND SHIFT DRUM ASSEMBLY .... 5-112
ENGINE REMOVAL
EAS23710
ENGINE REMOVAL
Removing the muffler and exhaust pipes
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
29 Nm (2.9 m kg, 21 ft Ib)
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
5
6
7
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)

T.
R.
44 Nm (4.4 m kg, 32 ft Ib)
8
LT
LT
9 New
4
12 New
10
New
New 15
T.
20 Nm (2.0 m kg, 14 ft Ib)
R.
3
13
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
11
T.
R.
T.
R.
20 Nm (2.0 m kg, 14 ft Ib)
LT
LT
14
48 Nm (4.8 m kg, 35 ft Ib)

R.
Order
T.
New 12
Job/Parts to remove
20 Nm (2.0 m kg, 14 ft Ib)

Qty
EXUP valve pulley cover
EXUP cable
O2 sensor coupler holder
O2 sensor coupler
Muffler bracket
Muffler
Gasket
10
Rear exhaust pipe cover
11
Rear exhaust pipe
12
Gasket
13
O2 sensor
14
Front exhaust pipe
Remarks
5-1
Disconnect.
Disconnect.
ENGINE REMOVAL
Removing the muffler and exhaust pipes
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
29 Nm (2.9 m kg, 21 ft Ib)
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
5
6
7
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)

T.
R.
44 Nm (4.4 m kg, 32 ft Ib)
8
LT
LT
9 New
4
12 New
10
New
New 15
T.
20 Nm (2.0 m kg, 14 ft Ib)
R.
3
13
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
11
T.
R.
T.
R.
20 Nm (2.0 m kg, 14 ft Ib)
LT
LT
14
48 Nm (4.8 m kg, 35 ft Ib)
15
R.
Order
T.
New 12
Job/Parts to remove
20 Nm (2.0 m kg, 14 ft Ib)

Qty
Gasket
Remarks
1
5-2
ENGINE REMOVAL
Removing the cylinder-#1 ignition coils and sidestand
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
LT
LT
LT
5
T.
R.
12 Nm (1.2 m kg, 8.7 ft Ib)
2
3
10
3
LT
6
11
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
T.
R.
13 Nm (1.3 m kg, 9.4 ft Ib)
16
17
18
New
14
12
7
19
LT
LT
LT
LT
LT
8
R.
R.
T.
T.
63 Nm (6.3 m kg, 45 ft Ib)
48 Nm (4.8 m kg, 35 ft Ib)

R.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
T.
Order
15
Job/Parts to remove
13
18 Nm (1.8 m kg, 13 ft Ib)
Qty
Remarks
Rider seat/Left side cover/Battery box/Air filter

case

4-1.
Fuel tank/Sub-fuel tank
Throttle body/Intake manifold/Pressure regulator bracket/Rollover valve/Canister
Rear brake master cylinder bracket
Drive pulley
Refer to BELT DRIVE on page 4-79.
Engine oil
Drain.
Refer to CHANGING THE ENGINE OIL on
page 3-11.
Transfer gear oil
Drain.
Refer to CHANGING THE TRANSFER
GEAR OIL on page 3-14.
Starter motor
Refer to ELECTRIC STARTER on page

5-77.
Spark plug cap
Ignition coil connector
Cylinder-#1 left ignition coil
Cylinder-#1 right ignition coil
5-3
Disconnect.
ENGINE REMOVAL
Removing the cylinder-#1 ignition coils and sidestand
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
LT
LT
LT
5
T.
R.
12 Nm (1.2 m kg, 8.7 ft Ib)
2
3
10
3
LT
6
11
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
T.
R.
13 Nm (1.3 m kg, 9.4 ft Ib)
16
17
18
New
14
12
7
19
LT
LT
LT
LT
LT
8
R.
R.
T.
T.
63 Nm (6.3 m kg, 45 ft Ib)
48 Nm (4.8 m kg, 35 ft Ib)

R.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
T.
Order
15
Job/Parts to remove
Qty
13
18 Nm (1.8 m kg, 13 ft Ib)

Remarks
Horn 1 connector
Except for California

Disconnect.
Horn 1
Except for California
Horn 2 coupler
10
Horn 2
11
Shift rod
12
Rear brake light switch coupler
13
Left rider footrest assembly
14
Shift pedal shaft bracket
15
Shift pedal (toe side)
16
Shift pedal (heel side)
17
Shift pedal shaft
18
Sidestand switch
19
Sidestand
1
5-4
ENGINE REMOVAL
ET1D71029
INSTALLING THE SHIFT PEDAL ASSEMBLY

1. Assemble:
Shift pedal (heel side) 1
Shift pedal (toe side) 2
T.
R.
Shift pedal (heel side) bolt

13 Nm (1.3 mkg, 9.4 ftlb)
NOTE:
Align the mark a on the pin on the toe side with

the mark b on the heel side.
2
1
2. Install:
T.
R.
Shift pedal bolt

18 Nm (1.8 mkg, 13 ftlb)
NOTE:

a
3. Adjust:
Shift rod length
Refer to ADJUSTING THE SHIFT PEDAL
on page 3-23.
5-5
ENGINE REMOVAL
Removing the oil cooler and oil filter bracket
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
R.
4
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
LS
R.
New
5
New
LS
3
New
LS
New
New
New
LS
T.
R.
LS
7 Nm (0.7 m kg, 5.1 ft Ib)
6
1
7
LS
T.
New
R.
New
(4)
LT
T.
R.
R.
Order
R.
R.
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
17 Nm (1.7 m kg, 12 ft Ib)
70 Nm (7.0 m kg, 50 ft lb)
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Oil cooler outlet hose
Oil cooler inlet hose
Oil cooler
Oil cooler bracket
Oil filter bolt
Oil filter bracket
Remarks
5-6
ENGINE REMOVAL
ET1D71028
CHECKING THE OIL COOLER

1. Check:
Oil cooler fins
Obstruction Clean.
Apply compressed air to the rear of the oil
cooler.
Damage Repair or replace.
NOTE:
Straighten any flattened fins with a thin, flathead

screwdriver.
2. Check:
Oil cooler inlet hose
Oil cooler outlet hose
5-7
ENGINE REMOVAL
Disconnecting the leads
1
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
12 3
4
13
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
5
6
15
LT
2
14
10
11
LT
Qty
7 Nm (0.7 m kg, 5.1 ft Ib)

Remarks
Refer to TRANSFER GEAR CASE on

page 5-81.
Drive pulley case

1
R.
R.
Job/Parts to remove
T.
T.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Spark plug cap
Stator coil lead
Neutral switch coupler
Neutral switch lead
Lead holder bracket
Wire harness guide
Throttle cable guide
Starter motor lead
Horn 2 lead
10
Rear brake light switch lead
11
Sidestand switch lead
12
Crankshaft position sensor coupler
13
Crankshaft position sensor lead
14
Rectifier/regulator lead
5-8
Disconnect.
Disconnect.
ENGINE REMOVAL
Disconnecting the leads
1
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
12 3
4
13
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
5
6
15
LT
2
14
10
11
LT
Qty
Speed sensor lead
R.
R.
15
Job/Parts to remove
T.
T.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
7 Nm (0.7 m kg, 5.1 ft Ib)

Remarks
1
5-9
ENGINE REMOVAL
Removing the engine
R.
R.
R.
59 Nm (5.9 m kg, 43 ft Ib)
T.
T.
T.
105 Nm (10.5 m kg, 75 ft lb)
T.
T.
R.
R.
18 Nm (1.8 m kg, 13 ft Ib)

T.
T.
R.
R.
98 Nm (9.8 m kg, 71 ft lb)
53 Nm (5.3 m kg, 38 ft Ib)
66 Nm (6.6 m kg, 48 ft Ib)
53 Nm (5.3 m kg, 38 ft Ib)
LT
19
22
12
17
1
13
5
15 18
20
24
23 4
E
21
11
16
25
10
18
14
9
T.
R.
30 Nm (3.0 m kg, 22 ft Ib)
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
13
T.
R.
T.
R.
Order
Job/Parts to remove
12
98 Nm (9.8 m kg, 71 ft lb)
Qty
53 Nm (5.3 m kg, 38 ft Ib)

Remarks
NOTE:
Place a suitable stand under the frame and
engine.
page 5-81.
Transfer gear case

1
Engine mounting bolt (right upper side)
Engine mounting bolt (left upper side)
Engine bracket bolt (right upper side)
Engine bracket (right upper side)
Engine bracket bolt (left upper side)
Engine bracket (left upper side)
Engine mounting nut (front upper side)
Engine mounting bolt (front upper side)
Engine cross-member bracket bolt
10
11
Engine bracket nut (front upper side)
12
Engine bracket bolt (front upper side)
13
Engine bracket (font upper side)
5-10
ENGINE REMOVAL
Removing the engine
R.
R.
R.
59 Nm (5.9 m kg, 43 ft Ib)
T.
T.
T.
105 Nm (10.5 m kg, 75 ft lb)
T.
T.
R.
R.
18 Nm (1.8 m kg, 13 ft Ib)

T.
T.
R.
R.
98 Nm (9.8 m kg, 71 ft lb)
53 Nm (5.3 m kg, 38 ft Ib)
66 Nm (6.6 m kg, 48 ft Ib)
53 Nm (5.3 m kg, 38 ft Ib)
LT
19
22
12
17
1
13
5
15 18
20
24
23 4
E
21
11
16
25
10
18
14
9
T.
R.
30 Nm (3.0 m kg, 22 ft Ib)
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
13
T.
R.
T.
R.
Order
Job/Parts to remove
Qty
14
Engine mounting nut (rear upper side)
15
Engine mounting bolt (rear upper side)
16
Engine bracket nut (rear upper side)
17
Engine bracket bolt (rear upper side)
18
Engine bracket (rear upper side)
19
Engine mounting nut (front lower side)
20
Spacer bolt
21
Engine mounting bolt (front lower side)
22
23
Engine mounting bolt (rear lower side)
24
Washer
25
Engine
12
98 Nm (9.8 m kg, 71 ft lb)

53 Nm (5.3 m kg, 38 ft Ib)
Remarks
Loosen.
5-11
ENGINE REMOVAL
3. Tighten:
Spacer bolt 1
ET1D71019
REMOVING THE ENGINE

1. Loosen:
Spacer bolt
Spacer bolt
18 Nm (1.8 mkg, 13 ftlb)
T.
NOTE:
R.
Loosen the spacer bolt with the pivot shaft

wrench 1.
NOTE:
Tighten the spacer bolt 1 to specification with

a pivot shaft wrench.
When tightened, the spacer bolt should be flat
against the engine surface.
Pivot shaft wrench

90890-01485
YM-01485
Pivot shaft wrench

90890-01485
YM-01485
3
5
1
EAS23720
INSTALLING THE ENGINE

1. Install:
Spacer bolt 1
Engine 2
Washer 3
Engine mounting bolt (rear lower side) 4
Engine mounting nut (rear lower side) 5
Engine mounting bolt (front lower side) 6
Engine mounting nut (front lower side) 7
Engine brackets (rear upper side) 8
Engine bracket bolts (rear upper side) 9
Engine bracket nuts (rear upper side) 10
Engine mounting bolt (rear upper side) 11
Engine mounting nut (rear upper side) 12
Engine bracket (left upper side) 13
Engine mounting bolts (left upper side) 14
Engine bracket bolts (left upper side) 15
Engine bracket (right upper side) 16
Engine mounting bolts (right upper side) 17
Engine bracket bolts (right upper side) 18
14 13 14
6
17
11
18 9
9 8
LT
15
16
2
8
12 10
4. Tighten:
Engine mounting nut (rear lower side) 5
Engine bracket nuts (rear upper side) 10
Engine mounting nut (rear upper side) 12
Engine mounting bolts (left upper side) 14
Engine bracket bolts (left upper side) 15
Engine mounting bolts (right upper side) 17
Engine bracket bolts (right upper side) 18
NOTE:
Lubricate the engine mounting bolt (front lower

side) threads and nut with engine oil.
of the engine mounting bolts (left upper side).
Do not fully tighten the bolts and nuts.
2. Remove:
5-12
ENGINE REMOVAL
T.
R.
9. Tighten:
Engine bracket nut (front upper side) 3
Engine cross-member bracket bolts 5
Engine mounting nut (front upper side) 7
Engine bracket nut (front upper
side)
53 Nm (5.3 mkg, 38 ftlb)
bolt
30 Nm (3.0 mkg, 22 ftlb)
Engine mounting nut (front upper
side)
98 Nm (9.8 mkg, 71 ftlb)
T.

side)
98 Nm (9.8 mkg, 71 ftlb)
Engine mounting nut (front lower
side)
105 Nm (10.5 mkg, 75 ftlb)
Engine bracket nut (rear upper
side)
53 Nm (5.3 mkg, 38 ftlb)
Engine mounting nut (rear upper
side)
98 Nm (9.8 mkg, 71 ftlb)
side)
66 Nm (6.6 mkg, 48 ftlb)
LOCTITE
59 Nm (5.9 mkg, 43 ftlb)
side)
53 Nm (5.3 mkg, 38 ftlb)
side)
53 Nm (5.3 mkg, 38 ftlb)
R.
3
7
6
2
1
5
4
5
1
5. Install:
Engine brackets (front upper side) 1
Engine bracket bolts (front upper side) 2
Engine bracket nuts (front upper side) 3
Engine cross-member bracket 4
Engine cross-member bracket bolts 5
Engine mounting bolt (front upper side) 6
Engine mounting nut (front upper side) 7
NOTE:
Do not fully tighten the bolts and nuts.

6. Install:
Lead holder bracket
Lead
(removed during engine removal)
NOTE:
To install and route the leads, refer to CABLE

7. Install:
Transfer gear case
Drive pulley case
Refer to TRANSFER GEAR CASE on page
5-81.
8. Install:
Drive pulley
Transfer gear case bracket
5-13
CAMSHAFTS
EAS23750
CAMSHAFTS
Removing the camshaft sprocket cover
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
R.
2
T.
R.
(5)
18 Nm (1.8 m kg, 13 ft Ib)
2
2
(3)
9
8
New 10
(3)
New
7
LS
6
T.
R.
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
3
T.
R.
Order
Job/Parts to remove
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)

18 Nm (1.8 m kg, 13 ft Ib)
Remarks
Fuel tank
Air filter case

4-1.
Muffler/Exhaust pipes
Spark plug cap
Spark plug
Shift pedal assembly
Damper cover
Damper
Timing mark accessing screw
Crankshaft end screw
Camshaft sprocket cover
Dowel pin
10
Camshaft sprocket cover gasket
Disconnect.
5-14
CAMSHAFTS
Removing the cylinder head covers
T.
R.
7
7 6
7
6
10 Nm (1.0 m kg, 7.2 ft Ib)
8
9
10 New
10 New
11
11
3
5
LT
T.
R.
Order
Job/Parts to remove
Qty
7 Nm (0.7 m kg, 5.1 ft Ib)

Remarks
Cylinder head breather hose
Oil tank breather hose
Wire harness guide
Fuel tank damper
Fuel outlet hose
Disconnect.
l = 40 mm (1.57 in)
20
l = 60 mm (2.36 in)
Rear cylinder head cover
Front cylinder head cover
10
Cylinder head cover gasket
11
Dowel pin
Disconnect.
5-15
CAMSHAFTS
Removing the push rods and rocker arms
T
R.
R.
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
24 Nm (2.4 m kg, 17 ft Ib)
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)

T.
R.
10
11
10
11
20 Nm (2.0 m kg, 14 ft Ib)
10
11
8
10
11
9
E
7
7
13
12
4
New 3
4
5
3 New
6
E
Order
Job/Parts to remove
Qty
Remarks
Rear rocker arm base assembly
Front rocker arm base assembly
Rocker arm base gasket
Dowel pin
Pull rod 1
l = 286.5 mm (11.280 in) pink painting
Pull rod 2
l = 288.5 mm (11.358 in) sky blue painting
Rocker arm shaft
Rocker arm 1
Rocker arm 2
10
Locknut
11
Adjusting screw
12
Rear rocker arm base
13
Front rocker arm base
1
5-16
CAMSHAFTS
Removing the valve lifters
LS
T.
LT
LT
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
2 New
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LS
LS
New
New
LT
LT
New
LS
2
LS
New 4
New 3
4 New
LS
LS
3 New
Order
Job/Parts to remove
Qty
Remarks
Refer to CYLINDERS AND PISTONS on
page 5-45.
Front cylinder
1
Push rod cover
O-ring
O-ring
Seal
Rear valve lifter case
Front valve lifter case
Valve lifter
4
5-17
CAMSHAFTS
Removing the camshafts and right balancer
18
M
20
T.
R.
T.
19
40 Nm (4.0 m kg, 29 ft Ib)
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
New
17 New
LS
New
16
15
21
18
9
2
New 3
14
11
(7)
13
12
10
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

E
Qty
Camshaft driven gear
Straight key
Circlip
Washer
Washer
Rear cylinder camshaft gear
Front cylinder camshaft gear
Straight key
10
Right balancer driven gear
11
Straight key
12
Camshaft drive gear
13
Right balancer drive gear
14
Straight key
15
Oil delivery pipe 1
16
Camshaft cover
17
Camshaft cover gasket
5-18
R.
R.
Job/Parts to remove
T.
T.
Order
40 Nm (4.0 m kg, 29 ft Ib)
60 Nm (6.0 m kg, 43 ft Ib)
Remarks
CAMSHAFTS
Removing the camshafts and right balancer
18
M
20
T.
R.
T.
19
40 Nm (4.0 m kg, 29 ft Ib)
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
New
17 New
LS
New
16
15
21
18
9
2
New 3
14
11
(7)
13
12
10
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

E
Qty
Dowel pin
19
Rear cylinder camshaft
20
Front cylinder camshaft
21
Right balancer
R.
R.
18
Job/Parts to remove
T.
T.
Order
40 Nm (4.0 m kg, 29 ft Ib)
60 Nm (6.0 m kg, 43 ft Ib)
Remarks
5-19
CAMSHAFTS
Disassembling the camshafts
5
4
6
New 1
2
3
2
1 New
5
7
4
E
E
Order
Job/Parts to remove
Qty
Circlip
Washer
Decompression cam spring
Decompression cam
Decompression pin
Front cylinder camshaft
Rear cylinder camshaft
Remarks
5-20
CAMSHAFTS
ET1D71030
REMOVING THE CYLINDER HEAD COVERS

1. Remove:
Front cylinder
Rear cylinder 1
NOTE:

2 cannot be removed when the cover is in
place. Loosen the bolts, and then remove the
cover from the right side of the vehicle, making
sure that the bolts do not scratch the rocker arms
or other engine parts.
2. Remove:
Rocker arm bases
(with the rocker arms)
3. Remove:
Valve lifters
NOTE:
Make a note of the position of each valve lifter so

that they can be installed in the correct place.
1
2
EAS23790
REMOVING THE ROCKER ARMS, PUSH

RODS AND VALVE LIFTERS
1. Align:
TDC mark a on the crankshaft position sensor rotor
(with the pointer b on the clutch cover)
a. Turn the crankshaft counterclockwise.

b. When piston #1 is at TDC on the compression stroke, align the TDC mark a on the
EAS23830
REMOVING THE CAMSHAFTS

1. Loosen:
Camshaft driven gear bolt 1
NOTE:
Place a folded copper washer 2 between the

teeth of the camshaft drive gear and camshaft
driven gear in order to lock them.
Do not damage the teeth of the camshaft drive
and camshaft driven gears.
If the marks are not aligned, turn the crankshaft counterclockwise 360 degrees and recheck step (b).
5-21
CAMSHAFTS
NOTE:

teeth of the right balancer drive gear and right
balancer driven gear in order to lock them.
Do not damage the teeth of the right balancer
drive and right balancer driven gears.
2. Remove:
Straight key
NOTE:
Cover the crankcase hole with a clean rag to

prevent the straight key from falling into the
crankcase.
3. Loosen:
Front cylinder camshaft gear bolt 1
NOTE:

teeth of the front cylinder camshaft gear and
rear cylinder camshaft gear in order to lock
them.
Do not damage the teeth of the front cylinder
camshaft and rear cylinder camshaft gears.
6. Remove:
Right balancer driven gear
Camshaft drive gear
Right balancer drive gear
Straight keys
NOTE:

prevent the straight keys from falling into the
crankcase.
4. Remove:
Rear cylinder camshaft gear
Front cylinder camshaft gear
Straight key
7. Remove:
Oil delivery pipe 1 1
Camshaft cover 2
NOTE:

crankcase.
NOTE:
Loosen each bolt 1/4 of a turn at a time, in stages and in a crisscross pattern. After all of the
bolts are fully loosened, remove them.
5. Loosen:
Camshaft drive gear bolt 1
Right balancer driven gear bolt 2
5-22
CAMSHAFTS
1
EAS23860
CHECKING THE CAMSHAFTS

1. Check:
Cam
Blue discoloration/pitting/scratches Replace the camshaft.
2. Measure:
Cam dimensions A a and B b
Out of specification Replace the camshaft.
Camshaft lobe dimensions
Intake A
42.53242.632 mm (1.6745
1.6784 in)
Limit
42.432 mm (1.6705 in)
Intake B
35.95036.050 mm (1.4154
1.4193 in)
Limit
35.850 mm (1.4114 in)
Exhaust A
42.53042.630 mm (1.6744
1.6783 in) (cylinder #1)
42.53142.631 mm (1.6744
1.6784 in) (cylinder #2)
Limit
42.430 mm (1.6705 in) (cylinder
#1)
42.431 mm (1.6705 in) (cylinder
#2)
Exhaust B
35.95036.050 mm (1.4154
1.4193 in)
Limit
35.850 mm (1.4114 in)
3. Measure:
Camshaft journal diameter (crankcase side)
a
Camshaft journal diameter
(crankcase side)
24.95724.980 mm (0.9826
0.9835 in)
a
a
4. Measure:
Camshaft journal diameter (camshaft cover
side) a
Camshaft journal diameter (camshaft cover side)
27.95727.980 mm (1.1007
1.1016 in)
5-23
CAMSHAFTS
NOTE:
Calculate the clearance by subtracting the camshaft journal diameter (crankcase side) from the
crankcase hole inside diameter.
Camshaft to crankcase clearance
0.0200.064 mm (0.00080.0025
in)
a
a
5. Measure:
Crankcase hole inside diameter a
Out of specification Replace the crankcase.
8. Calculate:
Camshaft to camshaft cover clearance
Out of specification Replace the defective
part(s).
NOTE:
Calculate the clearance by subtracting the camshaft journal diameter (camshaft cover side)
from the camshaft cover hole inside diameter.
Crankcase hole inside diameter

25.00025.021 mm (0.9843
0.9851 in)
Camshaft to camshaft cover

clearance
0.0200.064 mm (0.00080.0025
in)
9. Check:
Camshaft drive gears
Camshaft driven gears
Front cylinder camshaft gears
Rear cylinder camshaft gears
Chips/pitting/roughness/wear Replace the
defective part(s).
6. Measure:
Camshaft cover hole inside diameter a
Out of specification Replace the camshaft
cover.
EAS23890
CHECKING THE ROCKER ARMS AND

ROCKER ARM SHAFTS
rocker arms and rocker arm shafts.
1. Check:
Rocker arm
2. Check:
Rocker arm shaft
Blue discoloration/excessive wear/pitting/
scratches Replace or check the lubrication
system.
3. Measure:
Rocker arm inside diameter a
Camshaft cover hole inside diameter

28.00028.021 mm (1.1024
1.1032 in)
Rocker arm inside diameter

18.00018.018 mm (0.7087
0.7094 in)
7. Calculate:
Camshaft-to-crankcase clearance
part(s).
5-24
CAMSHAFTS
Push rod end
Bends/damage Replace.
2. Measure:
Push rod runout
Valve push rod runout
0.3 mm (0.012 in)
4. Measure:
Rocker arm shaft outside diameter a
Rocker arm shaft outside diameter
17.97617.991 mm (0.7077
0.7083 in)
EAS23920
CHECKING THE VALVE LIFTERS AND

VALVE LIFTER CASES
1. Check:
Valve lifter
Blue discoloration/excessive wear/pitting/
scratches Replace and check the lubrication system.
2. Check:
Valve lifter case 1
Damage/wear Replace the valve lifter
case.
O-rings 2
Damage/wear Replace the O-ring.
5. Calculate:
Rocker arm to rocker arm shaft clearance
NOTE:
Calculate the clearance by subtracting the rocker arm shaft outside diameter from the rocker
arm inside diameter.
Above 0.08 mm (0.003 in) Replace the defective part(s).
Rocker-arm-to-rocker-arm-shaft
clearance
0.0090.042 mm (0.00040.0017
in)
3. Measure:
Valve lifter outside diameter a
EAS23900
CHECKING THE ROCKER ARM BASES

1. Check:
Rocker arm base
EAS23910
CHECKING THE PUSH RODS

1. Check:
Push rod
5-25
CAMSHAFTS
Valve lifter outside diameter (intake)
22.96222.974 mm (0.9040
0.9045 in)
Valve lifter outside diameter (exhaust)
22.96222.974 mm (0.9040
0.9045 in)
Valve-lifter-to-valve-lifter-hole
clearance
0.0260.059 mm (0.00100.0023
in)
EAS23930
CHECKING THE PUSH ROD COVER

1. Check:
Push rod cover
Cranks/damage Replace.
Seal
O-ring
Damage/wear Replace the seal and Oring as a set.
EAS23980
CHECKING THE DECOMPRESSION SYSTEM

1. Check:
Decompression system
4. Measure:
Valve lifter case inside diameter a
NOTE:
Check that the decompression pin 1 projects

from the camshaft.
Check that the decompression cam 2 and decompression pin 1 moves smoothly.
Valve lifter hole inside diameter

(intake)
23.00023.021 mm (0.9055
0.9063 in)
Valve lifter hole inside diameter
(exhaust)
23.00023.021 mm (0.9055
0.9063 in)
2
a
2. Check:
Decompression cam
Decompression pin
ET1D71031
CHECKING THE DECOMPRESSION CAM

SPRING
The following procedure applies to all of the decompression cam springs.
1. Measure:
Decompression cam spring free length a
Out of specification Replace the decompression cam spring.
5. Calculate:
Valve lifter-to-valve lifter case clearance
NOTE:
Calculate the clearance by subtracting the valve

lifter outside diameter from the valve lifter case
inside diameter.
Above 0.072 mm (0.0028 in) Replace the
defective part(s).
5-26
CAMSHAFTS
EAS24030

Free length
20.0 mm (0.79 in)
Limit
19.0 mm (0.75 in)
INSTALLING THE CAMSHAFTS

1. Install:
Camshafts
NOTE:
Lubricate molybdenum disulfide oil onto the

camshaft journals and lobes.
2. Install:
Camshaft cover 1 1
Oil delivery pipe 1 2
NOTE:
Tighten the camshaft cover bolts in stages and

2
2. Measure:
Compressed decompression cam spring
force a
Out of specification Replace the decompression cam spring.

Installed compression spring
force
0.13350.1631 N (0.03000.0367
lb) (0.01360.0166 kgf)
Installed length
8.0 mm (0.31 in)
3. Install:
Straight keys
Right balancer drive gear 1
Right balancer driven gear 2
NOTE:

prevent the straight keys from falling into the
crankcase.
Align the punch mark a on the right balancer
drive gear 1 with the punch mark b on the
right balancer driven gear 2.
b. Installed length
EAS23990
CHECKING THE OIL DELIVERY PIPE

1. Check:
Oil delivery pipe 1
Damage Replace.
Obstruction Wash and blow out with compressed air.
O-rings
2
1
4. Tighten:
Camshaft drive gear bolt 1
Right balancer driven gear bolt 2
5-27
CAMSHAFTS
T.
R.
Camshaft drive gear bolt

60 Nm (6.0 mkg, 43 ftlb)
Right balancer driven gear bolt
40 Nm (4.0 mkg, 29 ftlb)
NOTE:
Align the projection a on the washer 3 with

the punch mark b on the front cylinder camshaft gear.
Install the conical spring washer 4 as shown
in the illustration.
Lubricate the front cylinder camshaft gear bolt
threads with engine oil.
NOTE:
Lubricate the camshaft drive gear bolt and right

balancer driven gear bolt threads with engine
oil.
Do not damage the teeth of the right balancer
drive and right balancer driven gears.
After tightening the camshaft driven gear bolt,
remove the copper washer to clean the teeth of
the right balancer drive gear and right balancer
driven gear.
4
5
6 New
1
6. Tighten:
Front cylinder camshaft gear bolt 1
T.
R.
Front cylinder camshaft gear bolt

40 Nm (4.0 mkg, 29 ftlb)
NOTE:

teeth of the front cylinder camshaft gear and
rear cylinder camshaft gear in order to lock
them.
Do not damage the teeth of the front cylinder
camshaft and rear cylinder camshaft gears.
After tightening the front cylinder camshaft
gear bolt, remove the copper washer to clean
the teeth of the front cylinder camshaft and rear
cylinder camshaft gears.
4
2
5. Install:
Rear cylinder camshaft gear 1
Front cylinder camshaft gear 2
Washer 3
Washer 5
Circlip 6 New
5-28
CAMSHAFTS
NOTE:

teeth of the camshaft drive gear and camshaft
driven gear in order to lock them.
Do not damage the teeth of the camshaft drive
and camshaft driven gears.
After tightening the camshaft driven gear bolt,
remove the copper washer to clean the teeth of
the camshaft drive and camshaft driven gears.
7. Install:
Straight key
Camshaft driven gear 1
NOTE:

crankcase.
Align the punch mark a on the camshaft driven gear 1 with the punch mark b on the
camshaft drive gear 2.
Insert a cross-headed screwdriver into one of
the holes in the outer camshaft driven gear and
rotate the gear until the teeth of both driven
gears are aligned. The teeth of both camshaft
driven gears must be aligned for installation.
EAS24050
BLEEDING A VALVE LIFTER

A valve lifter must be bled in the following cases.
When installing a new valve lifter
When the valve lifter leaks oil
1. Bleed:
Valve lifter
a. Fill a container with kerosene and place the

valve lifter into the container as shown.
Pump the plunger side of the valve lifter with
a press a number of times to let in kerosene.
ECA14630
CAUTION:
Do not pump the valve lifter excessively.

Kerosene is highly flammable.
8. Tighten:
Camshaft driven gear bolt 1
1. Kerosene
2. Valve lifter
T.
R.
Camshaft driven gear bolt

60 Nm (6.0 mkg, 43 ftlb)
b. Install the valve lifter into the engine.
5-29
CAMSHAFTS
h. Rotate the crankshaft until the mark (on the
camshaft driven gear) for the valve lifter to be
bled aligns with the camshaft drive gear as
shown.
Example:
For bleeding the cylinder #2 intake valve lifter, align mark 2 as shown.
ECA14650
CAUTION:
Be sure to install the valve lifter in its appropriate position.

Start the engine and warm it up.
Stop the engine.
Remove the camshaft sprocket cover.
Rotate the camshaft until the punch mark 1
on the camshaft driven gear aligns with the
punch mark on the camshaft drive gear as
shown. This is the condition in which piston
#1 is at top dead center (TDC).
NOTE:
1918 1
716
The crankshaft can be rotated smoothly when

the spark plugs are removed.
EWA12880
1 19
17 8
16
15
14
13
12
11
10
9
8
7
6
5
4 3
WARNING
2
2 1 1
15
14
13
12
11
10
9
8
7
6
5
4
3
c.
d.
e.
f.
Be careful since the engine is hot.

g. With piston #1 at TDC, count the indicated
number of gear teeth and place marks 2
through 5 on the camshaft driven gear as
shown. When these marks align between the
centers of the camshaft drive and driven
gears, the corresponding valve lifter is at its
highest point.
1. Piston #1 TDC punch mark

2. Cylinder #2 intake valve at its highest point
i. Leave the camshaft drive and driven gears

aligned for five minutes to allow the valve lifter to bleed.
j. If necessary, repeat steps (h) and (i) to bleed
other valve lifters.
1918 17 16 15
19
14
18
13
12
17
4
11
16
15
10
14
9
13
8
3
12
7
11
5 6
5
10
2
4
9
1
8
3
2
7
1
6 5
4 3 2 1
EAS24060
INSTALLING THE VALVE LIFTERS

1. Install:
Front valve lifter case
Rear valve lifter case
Valve lifters
T.
R.
1.
2.
3.
4.
5.
Piston #1 TDC punch mark

Cylinder #2 intake valve at its highest point
Cylinder #1 exhaust valve at its highest point
Cylinder #1 intake valve at its highest point
Cylinder #2 exhaust valve at its highest point
Valve lifter case bolt

10 Nm (1.0 mkg, 7.2 ftlb)
LOCTITE
NOTE:
Install the valve lifter in the correct place.

After installing the valve lifters, fill the tops of
them with engine oil.
5-30
CAMSHAFTS
a. Put the rocker arm base on the cylinder head.

b. Install the push rods.
NOTE:
Be sure to correctly install the push rods between the rocker arms and valve lifters as
shown. The illustration is viewed from the right
side of the vehicle.
The lengths of push rod 1 and push rod 2 are
different. Therefore, be sure to install them in
the proper position.
Lubricate the push rod end balls with engine
oil.
2. Install:
Push rod covers 1
NOTE:
Install the push rod covers so that their paint

marks a are facing towards the cylinder heads.
1
1
EAS24070
INSTALLING THE ROCKER ARMS AND

PUSH RODS
The following procedure applies to both cylinders.
1. Install:
Rocker arms 1
Rocker arm shafts 2
(onto rocker arm base)
A.
B.
1.
2.
3.
4.
5.
6.
NOTE:
The thread hole a of the rocker arm shaft must

face to the outside.
Rear cylinder
Front cylinder
Exhaust side rocker arm
Intake side rocker arm
Exhaust valve lifter
Intake valve lifter
Push rod 1 l = 286.5 mm (11.280 in)
Push rod 2 l = 288.5 mm (11.358 in)
c. Install the rocker arm base bolts (M6) 1 and

rocker arm base bolts (M8) 2 and 3.
NOTE:
Tighten the rocker arm base bolts in stages and

a
2
T.
2. Install:
Rocker arm base
(with rocker arms)
Push rods
R.
5-31
Rocker arm base bolt (M6)

10 Nm (1.0 mkg, 7.2 ftlb)
Rocker arm base bolt (M8)
24 Nm (2.4 mkg, 17ftlb)
CAMSHAFTS
Bolts 2: l = 45 mm (1.77 in)
Bolts 3: l = 70 mm (2.76 in)
1
5
3
2
5
5
5
5
EAS24080
INSTALLING THE CYLINDER HEAD

COVERS
1. Install:
Rear cylinder head cover 1
Front cylinder head cover 2
NOTE:

3 cannot be installed when the cover is in
place. Set the bolts in the cylinder head cover,
and then install the cover from the right side of
the vehicle.
ET1D71032
INSTALLING THE SHIFT PEDAL ASSEMBLY

1. Install:
NOTE:

T.
R.

10 Nm (1.0 mkg, 7.2 ftlb)
Bolts 4: l = 40 mm (1.57 in)

Bolts 5: l = 60 mm (2.36 in)
5-32
CYLINDER HEADS
EAS24110
CYLINDER HEADS
Removing the cylinder heads
T.
R.
59 Nm (5.9 m kg, 43 ft Ib)

T.
R.
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
66 Nm (6.6 m kg, 48 ft Ib)
2
LT
T.
LT
R.
T.
20 Nm (2.0 m kg, 14 ft Ib)
R.
53 Nm (5.3 m kg, 38 ft Ib)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
(3)
T.
R.
60 Nm (6.0 m kg, 43 ft Ib)
11
12
E
New 7
13 New
5 New
New 9
10
3
New 5
T.
R.
20 Nm (2.0 m kg, 14 ft Ib)
New
6 New
8
T.
Qty
R.
Job/Parts to remove
10
18 Nm (1.8 m kg, 13 ft Ib)

T.
Order
R.
New 9
21 Nm (2.1 m kg, 15 ft Ib)

Remarks
Throttle bodies/Intake manifolds
Cylinder head covers/Rocker arms
Oil pipe 1
Copper washer
Copper washer
Rear cylinder head
Front cylinder head
Cylinder head gasket
10
Dowel pin
11
Rear exhaust pipe joint cover
12
Rear exhaust pipe joint
5-33
CYLINDER HEADS
Removing the cylinder heads
T.
R.
59 Nm (5.9 m kg, 43 ft Ib)

T.
R.
T.
R.
53 Nm (5.3 m kg, 38 ft Ib)
66 Nm (6.6 m kg, 48 ft Ib)
2
LT
T.
LT
R.
T.
20 Nm (2.0 m kg, 14 ft Ib)
R.
53 Nm (5.3 m kg, 38 ft Ib)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
(3)
T.
R.
60 Nm (6.0 m kg, 43 ft Ib)
11
12
E
New 7
13 New
5 New
New 9
10
3
New 5
T.
R.
20 Nm (2.0 m kg, 14 ft Ib)
New
6 New
8
T.
Qty
Rear exhaust pipe gasket
R.
13
Job/Parts to remove
10
18 Nm (1.8 m kg, 13 ft Ib)

T.
Order
R.
New 9
21 Nm (2.1 m kg, 15 ft Ib)

Remarks
1
5-34
CYLINDER HEADS
EAS24140
REMOVING THE CYLINDER HEADS

1. Remove:
Cylinder head nuts
NOTE:
Loosen the nuts in the proper sequence as

shown.
Loosen each nut 1/2 of a turn at a time. After all
of the nuts are fully loosened, remove them.
A
2. Check:
Cylinder head
3. Measure:
Cylinder head warpage
Out of specification Resurface the cylinder
head.
Warpage limit
0.03 mm (0.0012 in)
a. Place a straightedge and a thickness gauge

across the cylinder head.
b. Measure the warpage.
c. If the limit is exceeded, resurface the cylinder
head as follows.
d. Place a 400600 grit wet sandpaper on the
surface plate and resurface the cylinder head
using a figure-eight sanding pattern.
A. Front cylinder
B. Rear cylinder
NOTE:
To ensure an even surface, rotate the cylinder

head several times.
EAS24170
CHECKING THE CYLINDER HEADS

The following procedure applies to all of the cylinder heads.
1. Eliminate:
Combustion chamber carbon deposits
(with a rounded scraper)
NOTE:
Do not use a sharp instrument to avoid damaging or scratching:

Spark plug bore threads
Valve seats
EAS24220
CHECKING THE OIL PIPE

1. Check:
Oil pipe 1
Damage Replace.
5-35
CYLINDER HEADS
EAS24250
INSTALLING THE CYLINDER HEADS

1. Install:
Cylinder head gasket 1 New

Dowel pins 2
NOTE:
The 1D7 mark on the cylinder head gasket

must face up and towards the left side of the cylinder.
A. Front cylinder
B. Rear cylinder
1 New
2
4. Install:
Copper washers New
Oil pipe 1
Oil pipe union bolt (M8)
T.
R.
2. Install:
Cylinder heads
Washers
Cylinder head nuts

18 Nm (1.8 mkg, 13ftlb)
Oil pipe union bolts (M10)
T.
R.
NOTE:
Lubricate the cylinder head nuts and washers

with engine oil.
NOTE:
Tighten the three union bolts evenly, and then

torque them to specification.
3. Tighten:
Cylinder head nuts
T.
R.
5. Install:
Engine bracket bolts (right upper side)
Engine mounting bolts (right upper side)
Engine bracket bolts (left upper side)
Engine mounting bolts (left upper side)
Cylinder head nut

60 Nm (6.0 mkg, 43 ftlb)
NOTE:
Tighten the cylinder head nuts in the proper

tightening sequence as shown and torque them
in two stages.

21 Nm (2.1 mkg, 15 ftlb)
NOTE:

of the engine mounting bolts (left upper side).
Do not fully tighten the bolts.
6. Tighten:
Engine mounting bolts (right upper side)
Engine mounting bolts (left upper side)
Engine bracket bolts (right upper side)
Engine bracket bolts (left upper side)
5-36
CYLINDER HEADS
T.
R.

59 Nm (5.9 mkg, 43 ftlb)
side)
66 Nm (6.6 mkg, 48 ftlb)
LOCTITE
side)
53 Nm (5.3 mkg, 38 ftlb)
side)
53 Nm (5.3 mkg, 38 ftlb)
5-37
VALVES AND VALVE SPRINGS

EAS24270

Removing the valves and valve springs
New 6
2
6 New
7
6 New
8
8
1
7
8
2
New 6
3
7
8
4 5
E
M
M
Order
Job/Parts to remove
Qty
Remarks
The following procedure applies to both cylinders.
Cylinder heads
Refer to CYLINDER HEADS on page 5-33.
Valve cotter
Upper spring seat
Valve spring
Intake valve
Exhaust valve
Valve stem seal
Lower spring seat
Valve guide
4
5-38

EAS24280
REMOVING THE VALVES

valves and related components.
NOTE:
Before removing the internal parts of the cylinder

head (e.g., valves, valve springs, valve seats),
make sure the valves properly seal.
1. Check:
Valve sealing
Leakage at the valve seat Check the valve
face, valve seat, and valve seat width.
Refer to CHECKING THE VALVE SEATS
on page 5-41.
3. Remove:
Upper spring seat 1
Valve spring 2
Valve 3
Valve stem seal 4
Lower spring seat 5
a. Pour a clean solvent a into the intake and

exhaust ports.
b. Check that the valves properly seal.
NOTE:
Identify the position of each part very carefully so

that it can be reinstalled in its original place.
NOTE:
There should be no leakage at the valve seat 1.
EAS24290
CHECKING THE VALVES AND VALVE

GUIDES
valves and valve guides.
1. Measure:
Valve-stem-to-valve-guide clearance
Out of specification Replace the valve
guide.
Valve-stem-to-valve-guide clearance =
Valve guide inside diameter a Valve stem diameter b
2. Remove:
Valve cotters
NOTE:
Remove the valve cotters by compressing the

valve springs with the valve spring compressor
set 1.
90890-04019
YM-04019
5-39

b. Install the new valve guide with the valve
guide installer 2 and valve guide remover
1.
Valve-stem-to-valve-guide clearance (intake)

0.0100.037 mm (0.00040.0015
in)
Limit
0.080 mm (0.0032 in)
Valve-stem-to-valve-guide clearance (exhaust)
0.0250.052 mm (0.00100.0020
in)
Limit
0.100 mm (0.0039 in)
c. After installing the valve guide, bore the valve

guide with the valve guide reamer 3 to obtain the proper valve-stem-to-valve-guide
clearance.
NOTE:
After replacing the valve guide, reface the valve

seat.
Valve guide remover (6)
90890-04064
Valve guide remover (6.0 mm)
YM-04064-A
Valve guide installer (6)
90890-04065
Valve guide installer (6.0 mm)
YM-04065-A
Valve guide reamer (6)
90890-04066
Valve guide reamer (6.0 mm)
YM-04066
2. Replace:
Valve guide
NOTE:
To ease valve guide removal and installation,

and to maintain the correct fit, heat the cylinder
head to 100 C (212 F) in an oven.
a. Remove the valve guide with the valve guide

remover 1.
3. Eliminate:
Carbon deposits
(from the valve face and valve seat)
4. Check:
Valve face
Pitting/wear Grind the valve face.
5-40

1. Eliminate:
Carbon deposits
(from the valve face and valve seat)
2. Check:
Valve seat
Pitting/wear Replace the cylinder head.
3. Measure:
Valve seat width C a
Out of specification Replace the cylinder
head.
Valve stem end

Mushroom shape or diameter larger than the
body of the valve stem Replace the valve.
5. Measure:
Valve margin thickness D a
Out of specification Replace the valve.
Valve margin thickness D (intake)
1.151.45 mm (0.04530.0571 in)
Limit
0.4 mm (0.02 in)
Valve margin thickness D (exhaust)
1.151.45 mm (0.04530.0571 in)
Limit
0.4 mm (0.02 in)
Valve seat width C (intake)

1.101.30 mm (0.04330.0512 in)
Limit
2.0 mm (0.08 in)
Valve seat width C (exhaust)
1.101.30 mm (0.04330.0512 in)
Limit
2.0 mm (0.08 in)
6. Measure:
Valve stem runout
Out of specification Replace the valve.
NOTE:
a. Apply Mechanics blueing dye (Dykem) b

onto the valve face.
When installing a new valve, always replace

the valve guide.
If the valve is removed or replaced, always replace the valve stem seal.
Valve stem runout
0.010 mm (0.0004 in)
b. Install the valve into the cylinder head.

c. Press the valve through the valve guide and
onto the valve seat to make a clear impression.
d. Measure the valve seat width.
NOTE:
Where the valve seat and valve face contacted

one another, the blueing will have been removed.
EAS24300
CHECKING THE VALVE SEATS

valves and valve seats.
5-41

4. Lap:
Valve face
Valve seat
NOTE:
After replacing the cylinder head or replacing the

valve and valve guide, the valve seat and valve
face should be lapped.
a. Apply a coarse lapping compound a to the

valve face.
e. Apply a fine lapping compound to the valve

face and repeat the above steps.
f. After every lapping procedure, be sure to
clean off all of the lapping compound from the
valve face and valve seat.
g. Apply Mechanics blueing dye (Dykem) b
onto the valve face.
ECA13790
CAUTION:
Do not let the lapping compound enter the

gap between the valve stem and the valve
guide.
b. Apply molybdenum disulfide oil onto the

valve stem.
h. Install the valve into the cylinder head.

i. Press the valve through the valve guide and
onto the valve seat to make a clear impression.
j. Measure the valve seat width c again. If the
valve seat width is out of specification, reface
and lap the valve seat.
c. Install the valve into the cylinder head.

d. Turn the valve until the valve face and valve
seat are evenly polished, then clean off all of
the lapping compound.
NOTE:
For the best lapping results, lightly tap the valve

seat while rotating the valve back and forth between your hands.
EAS24310
CHECKING THE VALVE SPRINGS

valve springs.
1. Measure:
Valve spring free length a
spring.
5-42

Free length (intake)
46.71 mm (1.84 in)
Limit
44.71 mm (1.76 in)
Free length (exhaust)
46.71 mm (1.84 in)
Limit
44.71 mm (1.76 in)
Spring tilt (intake)

2.5 /2.0 mm
Spring tilt (exhaust)
2.5 /2.0 mm
EAS24340
INSTALLING THE VALVES

valves and related components.
1. Deburr:
Valve stem end
(with an oil stone)
2. Measure:
Compressed valve spring force a
spring.
force (intake)
217.00249.00 N (48.7855.98 lb)
(22.1325.39 kgf)
force (exhaust)
217.00249.00 N (48.7855.98 lb)
(22.1325.39 kgf)
Installed length (intake)
32.66 mm (1.29 in)
Installed length (exhaust)
32.66 mm (1.29 in)
2. Lubricate:
Valve stem 1
Valve stem seal 2
(with the recommended lubricant)
Molybdenum disulfide oil
b. Installed length
3. Measure:
Valve spring tilt a
spring.
3. Install:
Valve guide 1
5-43

Lower spring seat 2
Valve stem seal 3
Valve 4
Valve spring 5
Upper spring seat 6
(into the cylinder head)
NOTE:
Make sure each valve is installed in its original

place.
Install the valve springs with the larger pitch a
facing up.
5. To secure the valve cotters onto the valve

stem, lightly tap the valve tip with a soft-face
hammer.
ECA13800
CAUTION:
Hitting the valve tip with excessive force

could damage the valve.
b. Smaller pitch
4. Install:
Valve cotters
NOTE:
Install the valve cotters by compressing the

valve springs with the valve spring compressor
set 1.
90890-04019
YM-04019
5-44
CYLINDERS AND PISTONS

EAS24360

Removing the cylinders and pistons
New 3
9
8
9
10
10
4
5 New
E
5
7
7
6
6
New 5
5 New
New
New 3
Order
Job/Parts to remove
Qty
Cylinder heads
Remarks
Front cylinder
Rear cylinder
Cylinder gasket
Dowel pin
Circlip
Piston pin
Piston
Top ring
2nd ring
10
Oil ring
2
5-45

EAS24380
NOTE:
REMOVING THE PISTON

1. Remove:
Piston pin clips 1
Piston pin 2
Piston 3
When removing a piston ring, open the end gap

with your fingers and lift the other side of the ring
over the piston crown.
ECA13810
CAUTION:
Do not use a hammer to drive the piston pin

out.
NOTE:
Before removing the piston pin clip, cover the

crankcase opening with a clean rag to prevent
the piston pin clip from falling into the crankcase.
For reference during installation, put an identification mark on each piston crown.
Before removing the piston pin, deburr the piston pin clips groove and the pistons pin bore
area. If both areas are deburred and the piston
pin is still difficult to remove, remove it with the
piston pin puller set 4.
EAS24410
CHECKING THE CYLINDERS AND PISTONS

The following procedure applies to all of the cylinders and pistons.
1. Check:
Piston wall
Cylinder wall
Vertical scratches Rebore or replace the
cylinder, and replace the piston and piston
rings as a set.
2. Measure:
Piston pin puller set

90890-01304
Piston pin puller
YU-01304
a. Measure cylinder bore C with the cylinder

bore gauge.
NOTE:
Measure cylinder bore C by taking side-to-side

and front-to-back measurements of the cylinder.
Then, find the average of the measurements.
Bore
100.000100.010 mm (3.9370
3.9374 in)
Taper limit
0.050 mm (0.0020 in)
Out of round limit
0.050 mm (0.0020 in)
C = maximum of D1D6
T = maximum of D1 or D2 - maximum of D5
or D6
R = maximum of D1, D3 or D5 - minimum of
D2, D4 or D6
2. Remove:
Top ring
2nd ring
Oil ring
5-46

EAS24430
CHECKING THE PISTON RINGS

1. Measure:
Piston ring side clearance
Out of specification Replace the piston
and piston rings as a set.
NOTE:
Before measuring the piston ring side clearance,

eliminate any carbon deposits from the piston
ring grooves and piston rings.
b. If out of specification, rebore or replace the
rings as a set.
c. Measure piston skirt diameter D a with the
micrometer.
Piston ring
Top ring
Ring side clearance
0.0300.080 mm (0.0012
0.0032 in)
Limit
0.120 mm (0.0047 in)
2nd ring
Ring side clearance
0.0300.070 mm (0.0012
0.0028 in)
Limit
0.120 mm (0.0047 in)
Piston
Diameter D
99.96099.975 mm (3.9354
3.9360 in)
b. 10 mm (0.39 in) from the bottom edge of the

piston
d. If out of specification, replace the piston and

piston rings as a set.
e. Calculate the piston-to-cylinder clearance
with the following formula.
Piston-to-cylinder clearance =
Cylinder bore C Piston skirt diameter D
2. Install:
Piston ring
(into the cylinder)
NOTE:
Level the piston ring into the cylinder with the

piston crown.
0.0250.050 mm (0.00100.0020
in)
Limit
0.15 mm (0.0059 in)
f. If out of specification, rebore or replace the
rings as a set.
a. 10 mm (0.39 in)
5-47

3. Measure:
Piston ring end gap
Out of specification Replace the piston
ring.
NOTE:
The oil ring expander spacers end gap cannot

be measured. If the oil ring rails gap is excessive, replace all three piston rings.
Piston ring
Top ring
End gap (installed)
0.200.35 mm (0.00790.0138
in)
Limit
0.55 mm (0.0217 in)
2nd ring
End gap (installed)
0.450.60 mm (0.01770.0236
in)
Limit
0.95 mm (0.0374 in)
Oil ring
End gap (installed)
0.200.70 mm (0.00790.0276
in)
3. Measure:
Piston pin bore diameter b
Out of specification Replace the piston.
Piston pin bore inside diameter
23.00423.015 mm (0.9057
0.9061 in)
Limit
23.045 mm (0.9073 in)
EAS24440
CHECKING THE PISTON PINS

The following procedure applies to all of the piston pins.
1. Check:
Piston pin
Blue discoloration/grooves Replace the
piston pin and then check the lubrication system.
2. Measure:
Piston pin outside diameter a
Out of specification Replace the piston pin.
4. Calculate:
Piston-pin-to-piston-pin-bore clearance
Out of specification Replace the piston pin
and piston as a set.
Piston-pin-to-piston-pin-bore clearance =
Piston pin bore diameter b Piston pin outside diameter a
Piston-pin-to-piston-pin-bore
clearance
0.0040.024 mm (0.00016
0.00094 in)
Piston pin outside diameter

22.99123.000 mm (0.9052
0.9055 in)
Limit
22.971 mm (0.9044 in)
EAS24460
INSTALLING THE PISTONS AND

CYLINDERS
The following procedure applies to all of the pistons and cylinders.
1. Install:
Top ring 1
2nd ring 2
Lower oil ring rail 3
Upper oil ring rail 4
5-48

3. Lubricate:
Piston
Piston rings
Cylinder
Oil ring expander 5

NOTE:
Be sure to install the piston rings so that the

manufacturers marks or numbers face up.
Engine oil
4. Offset:
Piston ring end gaps
A
90
d.e
2. Install:
Piston 1
Piston pin 2
90
Piston pin clips 3 New

NOTE:
45
Apply engine oil onto the piston pin.

Make sure the arrow mark a on the piston faces towards the front of the vehicle.
Before installing the piston pin clips, cover the
crankcase opening with a clean rag to prevent
the clip from falling into the crankcase.
Install the piston pin clips, so that the clip ends
are 3 mm (0.12 in) b or more from the cutout
in the piston.
Reinstall each piston into its original cylinder
(numbering order starting from the left: #1 to
#2).
a.
b.
c.
d.
e.
A.
a.c
Top ring
Upper oil ring rail
Oil ring expander
Lower oil ring rail
2nd ring
forward
5. Install:
Cylinder 1
NOTE:
While compressing the piston rings with one

hand, install the cylinder with the other hand.
b
3 New
5-49
CLUTCH
EAS25060
CLUTCH
Removing the clutch cover
T.
R.
12 Nm (1.2 m kg, 8.7 ft Ib)
5
T.
R.
New 4
(5)
(11)
T.
R.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)
Remarks
Engine oil
Drain.
page 3-11.
Left side cover

4-1.
Horn 1/Canister

For California only
Fuel tank/Sub-fuel tank
Left rider footrest assembly/Shift rod/Sidestand
Generator cover
Refer to GENERATOR AND STARTER

CLUTCH on page 5-72.
Drive pulley case

page 5-81.
Shift arm
Clutch cover
Clutch cover gasket
5-50
Disconnect.
CLUTCH
Removing the clutch cover
T.
R.
12 Nm (1.2 m kg, 8.7 ft Ib)
5
T.
R.
New 4
(5)
(11)
R.
T.
3
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Dowel pin
10 Nm (1.0 m kg, 7.2 ft Ib)
Remarks
2
5-51
CLUTCH
Removing the crankshaft position sensor
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

LT
LT
LT
LT
LT
LT
4
6
LT
2
New 1
LS
Order
Job/Parts to remove
Qty
Oil seal
Bearing
Clutch cover damper plate
Clutch cover damper
Crankshaft position sensor lead holder
Crankshaft position sensor
Remarks
5-52
CLUTCH
Removing the clutch
LS
28
27
26 25
24
New
23
19
E
20
22
17
R.
18
T.
21
105 Nm (10.5 m kg, 75 ft lb)
16
23
32
15 14
13 12 New
New
33
9
31
30 29
11
65
10
E
T.
R.
105 Nm (10.5 m kg, 75 ft lb)
(6)
New
LS
E
T.
R.
Order
Job/Parts to remove
Qty
Clutch spring plate retainer
Clutch spring plate
Clutch spring plate seat
Pressure plate
Short clutch push rod
Friction plate 1
Clutch plate
Friction plate 2
Clutch boss nut
10
11
Washer
12
Wire circlip
13
Clutch plate
14
Friction plate 3
15
Clutch damper spring
16
Clutch damper spring seat
17
Clutch boss
5-53
8 Nm (0.8 m kg, 5.8 ft Ib)
Remarks
Inside diameter: 124 mm (4.88 in)
Inside diameter: 135 mm (5.31 in)
CLUTCH
Removing the clutch
LS
28
27
26 25
24
New
23
19
E
20
22
17
R.
18
T.
21
105 Nm (10.5 m kg, 75 ft lb)
16
23
32
15 14
13 12 New
New
33
9
31
30 29
11
65
10
E
T.
R.
105 Nm (10.5 m kg, 75 ft lb)
(6)
New
LS
E
T.
R.
Order
18
Job/Parts to remove
Qty
Thrust washer 1
19
Clutch housing
20
Circlip
21
Washer
22
Oil pump drive gear
23
Dowel pin
24
Bearing
25
Collar
26
Thrust washer 2
27
Ball
28
Long push rod
29
Spacer
30
Crankshaft position sensor rotor
31
Primary drive gear
32
Straight key
33
Washer
8 Nm (0.8 m kg, 5.8 ft Ib)
Remarks
5-54
CLUTCH
Removing the left balancer
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

LT
12 New
(6)
8
10
LS
1 11
2
LS
(3)
New 3
5
4
R.
LS
3 New
T.
LT
10 Nm (1.0 m kg, 7.2 ft Ib)
E
T.
R.
Order
40 Nm (4.0 m kg, 29 ft Ib)
Job/Parts to remove
Qty
Left balancer idle gear shaft holder
Dowel pin
O-ring
Left balancer idle gear
Left balancer idle gear shaft
Left balancer drive gear
Straight key
Left balancer driven gear
Left balancer weight 1
Remarks
10
Left balancer weight 2
11
12
Gasket
1
5-55
CLUTCH
Removing the clutch master cylinder
T.
R.
30 Nm (3.0 m kg, 22 ft Ib)
13
New 10
LS
6
7
9
8
12
11
LT
T.
R.
Order
Job/Parts to remove
10 Nm (1.0 m kg, 7.2 ft Ib)
Qty
Remarks
Drain.
CLUTCH SYSTEM on page 3-15.
Clutch fluid
1
Left rearview mirror
Clutch master cylinder reservoir cap
Clutch master cylinder reservoir diaphragm

holder
Clutch lever
Clutch master cylinder push rod pin
Clutch switch coupler
Clutch switch
10
Copper washer
11
Clutch hose
12
13
Clutch master cylinder
Disconnect.
5-56
CLUTCH
Disassembling the clutch master cylinder
LS
5 New
4
3 New
2
1
Order
Job/Parts to remove
Qty
Clutch master cylinder push rod
Dust boot
Circlip
Washer
Clutch master cylinder kit
Clutch master cylinder body
Remarks
5-57
CLUTCH
Removing the clutch release cylinder
T.
R.
19 Nm (1.9 m kg, 13 ft Ib)
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
New 3
4
6
T.
R.
26 Nm (2.6 m kg, 19 ft Ib)
5
T.
R.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Remarks
Clutch fluid
Drain.
Clutch pipe union bolt cap
Copper washer
Clutch pipe
Clutch release cylinder
Dowel pin
2
5-58
CLUTCH
Disassembling the clutch release cylinder
.
R.
6 Nm (0.6 m kg, 4.3 ft Ib)
LS
6
3
New 4
2
LS
Order
Job/Parts to remove
Qty
Boots
Clutch release cylinder piston
Clutch release cylinder spring
Clutch release cylinder piston seal
Bleed screw
Clutch release cylinder body
Remarks
5-59
CLUTCH
EAS25080
REMOVING THE CLUTCH

1. Loosen:
Clutch boss nut 1
Sheave holder
90890-01701
YS-01880-A
NOTE:
While holding the clutch boss 2 with the universal clutch holder 3, loosen the clutch boss nut.
90890-04086
YM-91042
2. Remove:
Clutch boss nut 1
Washer 3
Clutch boss assembly 4
3
2
ET1D71021
NOTE:
There is a built-in damper between the clutch

boss and the clutch plate. It is not necessary to
remove the wire circlip 5 and disassemble the
built-in damper unless there is serious clutch
chattering.
REMOVING THE LEFT BALANCER DRIVE

GEAR
1. Loosen:
Left balancer drive gear bolt 1
NOTE:
While the holding the generator rotor 2 with the

primary sheave holder 3, loosen the left balancer drive gear bolt.
Sheave holder
90890-01701
YS-01880-A
5
3
EAS25090
REMOVING THE PRIMARY DRIVE GEAR

1. Loosen:
Primary drive gear bolt 1
NOTE:
While holding the generator rotor 2 with the

sheave holder 3, loosen the primary drive gear
bolt.
5-60
CLUTCH
3
2
A. Friction plate 1, 3
B. Friction plate 2
EAS25100
CHECKING THE FRICTION PLATES

The following procedure applies to all of the friction plates.
1. Check:
Friction plate
Damage/wear Replace the friction plates
as a set.
2. Measure:
Friction plate thickness
Out of specification Replace the friction
plates as a set.
EAS25110
CHECKING THE CLUTCH PLATES

clutch plates.
1. Check:
Clutch plate
Damage Replace the clutch plates as a
set.
2. Measure:
Clutch plate warpage
(with a surface plate and thickness gauge 1)
Out of specification Replace the clutch
plates as a set.
NOTE:
Measure the friction plate at four places.
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-9
Friction plate 1, 3 thickness

2.903.10 mm (0.1140.122 in)
Wear limit
2.80 mm (0.110 in)
Friction plate 2 thickness
2.923.08 mm (0.1150.121 in)
Wear limit
2.82 mm (0.111 in)
Clutch plate thickness

1.902.10 mm (0.0750.083 in)
Warpage limit
0.20 mm (0.0079 in)
EAS25130
CHECKING THE CLUTCH SPRING PLATE

1. Check:
Clutch spring plate
Damage Replace.
5-61
CLUTCH
Bearing
2. Check:
Clutch spring plate seat
Damage Replace.
EAS25190
CHECKING THE CLUTCH PUSH RODS

1. Check:
O-ring
Short clutch push rod
Long clutch push rod
Ball
Cracks/damage/wear Replace the defective part(s).
2. Measure:
Long clutch push rod bending limit
part(s).
EAS25150
CHECKING THE CLUTCH HOUSING

1. Check:
Clutch housing dogs
Damage/pitting/wear Deburr the clutch
housing dogs or replace the clutch housing.
NOTE:
Pitting on the clutch housing dogs will cause erratic clutch operation.
Long clutch push rod bending

limit
0.30 mm (0.0118 in)
EAS25200
CHECKING THE PRIMARY DRIVE GEAR

1. Check:
Primary drive gear
Damage/wear Replace the primary drive
and primary driven gears as a set.
Excessive noise during operation Replace
the primary drive and primary driven gears as
a set.
2. Check:
Bearing
Damage/wear Replace the bearing and
clutch housing.
EAS25160
CHECKING THE CLUTCH BOSS

1. Check:
Clutch boss splines
Damage/pitting/wear Replace the clutch
boss.
EAS25210
CHECKING THE PRIMARY DRIVEN GEAR

1. Check:
Primary driven gear 1
Damage/wear Replace the primary drive
and primary driven gears as a set.
Excessive noise during operation Replace
the primary drive and primary driven gears as
a set.
NOTE:
Pitting on the clutch boss splines will cause erratic clutch operation.
EAS25170
CHECKING THE PRESSURE PLATE

1. Check:
Pressure plate
ET1D71033
CHECKING THE LEFT BALANCER GEARS

1. Check:
Left balancer drive gear
5-62
CLUTCH
Left balancer driven gear
Left balancer idle gear
Burrs/chips/roughness/wear Replace the
defective part(s).
2. Measure:
Left balancer driven gear inside diameter a
NOTE:
Calculate the clearance by subtracting the left

balancer driven gear housing outside diameter
from the left balancer driven gear inside diameter.
Left-balancer-driven-gear-to-leftbalancer-driven-gear-housing
clearance
0.0500.103 mm (0.00200.0041
in)
Left balancer driven gear inside

diameter a
59.01059.028 mm (2.3232.324
in)
Limit
59.100 mm (2.327 in)
ET1D71022
INSTALLING THE LEFT BALANCER DRIVE

GEAR
1. Install:
Left balancer weight 1 1
Left balancer weight 2 2
Left balancer driven gear 3
NOTE:
Make sure that the punch marks a on the left

balancer driven gear are facing toward left balancer weight 2.
Left balancer weight bolt
10 Nm (1.0 mkg, 7.2 ftlb)
LOCTITE
T.
3. Measure:
Left balancer driven gear housing outside diameter a
R.
Left balancer driven gear housing outside diameter a

58.92558.960 mm (2.3202.321
in)
Limit
58.900 mm (2.318 in)
3
2
a
a
1
2. Install:
Left balancer drive gear 1
Left balancer idle gear 2
Left balancer driven gear 3
NOTE:
Align the punch mark a on the left balancer

drive gear with the punch mark b on the left
balancer idle gear.
Align the punch marks c on the left balancer
idle gear with the punch marks d on the left
balancer driven gear.
4. Calculate:
Left-balancer-driven-gear-to-left-balancerdriven-gear-housing clearance
part(s).
5-63
CLUTCH
Crankshaft position sensor rotor 1

Spacer
Primary drive gear bolt 2
T.
R.
1
a
Primary drive gear bolt

105 Nm (10.5 mkg, 75 ftlb)
EC1D71007
CAUTION:
b 2
The timing marks on the crankshaft position

sensor rotor must face outside.
3. Tighten:
Left balancer drive gear bolt 1
NOTE:
T.
R.
Lubricate the primary drive gear bolt threads

with engine oil.
sheave holder 4, tighten the primary drive
gear bolt.
Left balancer drive gear bolt

40 Nm (4.0 mkg, 29 ftlb)
NOTE:

sheave holder 3, tighten the left balancer drive
gear bolt.
Sheave holder
90890-01701
YS-01880-A
Sheave holder
90890-01701
YS-01880-A
1
2
1
4
3
3
EAS25260
INSTALLING THE CLUTCH

1. Install:
Clutch housing
Thrust washer
EAS25230
INSTALLING THE PRIMARY DRIVE GEAR

1. Install:
Washer
Straight key
Primary drive gear
NOTE:
Lubricate the clutch housing bearings with engine oil.
5-64
CLUTCH
Make sure that the primary driven gear teeth
and primary drive gear teeth mesh correctly.
Make sure that the primary driven gear teeth
and oil pump driven gear teeth mesh correctly.
2. Install:
Clutch boss assembly 1
NOTE:
Install the clutch damper spring 2 with the

OUTSIDE mark facing out.
If the wire circlip 3 has been removed, carefully install a new one.
4. Lubricate:
Friction plates
Clutch plates
Engine oil
5. Install:
Friction plates 2 1
Clutch plates
Friction plate 1 2
2
New 3
3. Install:
Clutch boss 1
Washer
Clutch boss nut 3
NOTE:
First, install a friction plate and then alternate

between a clutch plate and a friction plate.
Align a projection on each friction plate 2 1
with the mark a on the clutch housing
and align a projection on friction plate 1 2 with
the punch mark b on the housing.
T.
R.
Clutch boss nut

105 Nm (10.5 mkg, 75 ftlb)
NOTE:
Lubricate the clutch boss nut threads and conical spring washer mating surfaces with engine
oil.
While holding the clutch boss with the universal clutch holder 4, tighten the clutch boss
nut.
Stake the clutch boss nut 3 at a cutout b in
the main axle.
a
1
b
2
6. Install:
Clutch spring plate
Clutch spring plate retainer
T.

90890-04086
YM-91042
R.
Clutch spring plate retainer bolt

8 Nm (0.8 mkg, 5.8 ftlb)
NOTE:
Tighten the clutch spring plate retainer bolts in

stages and in a crisscross pattern.
5-65
CLUTCH
7. Apply:
Sealant
(onto the crankshaft position sensor lead
grommet)
NOTE:
To collect any remaining clutch fluid, place a

of the clutch hose.

90890-85505
2
1
3
ET1D71037
CHECKING THE CLUTCH MASTER

CYLINDER
1. Check:
Clutch master cylinder
Clutch fluid delivery passage
(clutch master cylinder body)
2. Check:
Clutch master cylinder kit
3. Check:
Clutch master cylinder reservoir
4. Check:
Clutch hose
8. Install:
Shift arm 1
T.
R.
Shift arm bolt

12 Nm (1.2 mkg, 8.7 ftlb)
NOTE:
Install the shift arm 1 with its slot a aligned

with the mark b in end of the shift shaft.
EAS25300
ASSEMBLING THE CLUTCH MASTER

CYLINDER
EW1D71010
EAS25280
WARNING
DISASSEMBLING THE CLUTCH MASTER

CYLINDER
Before installation, all internal clutch components must be cleaned and lubricated
with clean or new clutch fluid.
Never use solvents on internal clutch components.
NOTE:
Before disassembling the clutch master cylinder,

drain the clutch fluid from the entire clutch system.
1. Remove:
Clutch hose union bolt 1
Copper washers 2
Clutch hose 3

Brake fluid DOT 4
5-66
CLUTCH
EAS25310
INSTALLING THE CLUTCH MASTER

CYLINDER
1. Install:
Clutch master cylinder 1
Clutch master cylinder holder 2
T.
R.

bolt
10 Nm (1.0 mkg, 7.2 ftlb)
2
1030
3. Fill:
(with the specified amount of the recommended clutch fluid)
NOTE:
Align the end of the clutch lever holder with the

punch mark a on the handlebar.
First, tighten the rear bolt, then the front bolt.

Brake fluid DOT 4
1
EWA13370
WARNING

clutch performance.
2. Install:
Copper washers New
Clutch hose 1
Clutch hose union bolt 2
T.
R.

30 Nm (3.0 mkg, 22 ftlb)
ECA13420
EW1D71002
CAUTION:
WARNING

Proper clutch hose routing is essential to insure safe vehicle operation. Refer to CABLE
NOTE:
NOTE:

fluid level, make sure the top of the reservoir is
horizontal.
Install the clutch hose at 1030 angle to the

clutch master cylinder as shown in the illustration.
While holding the clutch hose, tighten the
union bolt.
Turn the handlebar to the left and right to make
sure the clutch hose does not touch other parts
(e.g., wire harness, cables, leads). Correct if
necessary.
4. Bleed:
Clutch system
5. Check:
Clutch fluid level
LEVEL on page 3-14.
5-67
CLUTCH
1. Install:
Clutch release cylinder body
Cracks/damage Replace the clutch release cylinder.
2. Check:
Clutch release cylinder 1
Clutch release cylinder piston 2
Rust/scratches/wear Replace the clutch
release cylinder and clutch release cylinder
piston as a set.
6. Check:
Clutch lever operation
Soft or spongy feeling Bleed the clutch
system.
1
2
ET1D71004
REMOVING THE CLUTCH RELEASE

CYLINDER
1. Remove:
Clutch pipe union bolt 1
Copper washers 2
Clutch pipe 3
EAS25340
ASSEMBLING THE CLUTCH RELEASE

CYLINDER
EW1D71006
NOTE:
WARNING
Put the end of the clutch pipe into a container

and pump out the clutch fluid carefully.
Before installation, all internal clutch components must be cleaned and lubricated
with clean or new clutch fluid.
Never use solvents on internal clutch components as they will cause the piston seal
Whenever a clutch release cylinder is disassembled, replace the piston seal.

Brake fluid DOT 4
3
EAS25350
EAS25330
INSTALLING THE CLUTCH RELEASE

CYLINDER
1. Install:
CHECKING THE CLUTCH RELEASE

CYLINDER
Recommended clutch component replacement schedule
Clutch hose
Every four years
Clutch fluid
Every two years and

whenever the clutch
is disassembled
R.
Every two years
T.
Piston seal
Copper washers New

Clutch pipe 1
Clutch pipe union bolt 2
26 Nm (2.6 mkg, 19 ftlb)
EW1D71003
WARNING
Proper clutch pipe routing is essential to insure safe vehicle operation. Refer to CABLE
5-68
CLUTCH
4. Check:
Clutch fluid level
LEVEL on page 3-14.
EC1D71005
CAUTION:
When installing the clutch pipe onto the

clutch release cylinder, make sure the pipe
a touches the projection b on the clutch
release cylinder.
2
a
b
1
5. Check:
Clutch lever operation
Soft or spongy feeling Bleed the clutch
system.
2. Fill:
(with the specified amount of the recommended clutch fluid)
Brake fluid DOT 4
EWA13370
WARNING

clutch performance.
ECA13420
CAUTION:

NOTE:

fluid level, make sure that the top of the reservoir
is horizontal.
3. Bleed:
Clutch system
5-69
SHIFT SHAFT
EAS25410
SHIFT SHAFT
Removing the shift shaft and stopper lever
T.
R.
22 Nm (2.2 m kg, 16 ft Ib)
LT
8
New
LS
1
2
4
7
3
E
New 2
6
5
LT
T.
R.
Order
Job/Parts to remove
Qty
Clutch housing
10 Nm (1.0 m kg, 7.2 ft Ib)
Remarks
Refer to CLUTCH on page 5-50.
Washer
Circlip
Shift shaft
Shift shaft spring
Stopper lever
Collar
Stopper lever spring
Shift shaft spring stopper
1
5-70
SHIFT SHAFT
EAS25420
CHECKING THE SHIFT SHAFT

1. Check:
Shift shaft
Bends/damage/wear Replace.
Shift shaft spring
EAS25430
CHECKING THE STOPPER LEVER

1. Check:
Stopper lever
Bends/damage Replace.
Roller turns roughly Replace the stopper
lever.
Stopper lever spring
EAS25450
INSTALLING THE SHIFT SHAFT

1. Install:
Stopper lever 1
Collar
Stopper lever bolt 2
Stopper lever spring 3
T.
R.
Stopper lever bolt

10 Nm (1.0 mkg, 7.2 ftlb)
LOCTITE
NOTE:
Hook the ends of the stopper lever spring onto

the stopper lever and the crankcase boss 4.
Mesh the stopper lever with the shift drum segment assembly.
4
3
1
2
2. Install:
Washers
Circlips
Shift shaft spring 1
Shift shaft 2
NOTE:
Hook the end of the shift shaft spring onto the

shift shaft spring stopper 3.
5-71
GENERATOR AND STARTER CLUTCH

EAS24480

Removing the stator coil
1
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
R.
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
R.
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LS
New
LT
6
2
New
LS
LT
LT
New
5
4 New
LT
(5)
R.
R.
Order
T.
T.
10 Nm (1.0 m kg, 7.2 ft Ib)

Job/Parts to remove
10 Nm (1.0 m kg, 7.2 ft Ib)

Qty
Remarks
Engine oil
Drain.
page 3-11.
Lead cover
Clutch pipe
Stator coil coupler
Oil delivery pipe 2
Generator cover
Generator cover gasket
Dowel pin
Stator coil lead holder
Stator coil
Disconnect.
5-72

Removing the generator rotor
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)
8
6
LT
LT
LT
2
E
E
(6)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
E
.
T
R.
Order
80 Nm (8.0 m kg, 58 ft Ib)
Job/Parts to remove
Qty
Torque limiter
Starter clutch idle gear shaft
Starter clutch idle gear
Generator rotor
Starter clutch
Woodruff key
Starter clutch gear
Bearing
Bearing housing
Remarks
5-73

EAS24490
NOTE:
REMOVING THE GENERATOR

1. Remove:
Generator rotor bolt 1
Washer

sheave holder 2, loosen the starter clutch
bolts.
NOTE:
Sheave holder
90890-01701
YS-01880-A

sheave holder 3, loosen the generator rotor
bolt.
Sheave holder
90890-01701
YS-01880-A
EAS24570
CHECKING THE STARTER CLUTCH

1. Check:
Starter clutch rollers
2. Check:
Starter clutch idle gear
Starter clutch gear
Burrs/chips/roughness/wear Replace the
defective part(s).
3. Check:
Starter clutch gears contacting surfaces
Damage/pitting/wear Replace the starter
clutch gear.
4. Check:
Starter clutch operation
3
1
2. Remove:
Generator rotor 1
(with the rotor puller 2)
Woodruff key
Rotor puller
90890-01080
Stator rotor puller
YM-01080-A
a. Install the starter clutch gear 1 onto the

starter clutch and hold the generator rotor 2.
b. When turning the starter clutch gear clockwise A, the starter clutch and the starter
clutch gear should engage, otherwise the
starter clutch is faulty and must be replaced.
c. When turning the starter clutch gear counterclockwise B, it should turn freely, otherwise
the starter clutch is faulty and must be replaced.
EAS24560
REMOVING THE STARTER CLUTCH

1. Remove:
Starter clutch bolts
Starter clutch
5-74

Generator rotor 1
Washer
NOTE:
Clean the tapered portion of the generator

shaft and the generator rotor hub.
When installing the rotor, make sure the woodruff key is properly seated in the key way of
the generator shaft.
Lubricate the generator rotor bolt threads and
washer mating surfaces with engine oil.
ET1D71020
CHECKING THE TORQUE LIMITER

1. Check:
Torque limiter
NOTE:
Do not disassemble the torque limiter.
EAS24600
INSTALLING THE STARTER CLUTCH

1. Install:
Starter clutch
2. Tighten:
T.
T.
R.
Starter clutch bolt

24 Nm (2.4 mkg, 17 ftlb)
LOCTITE
R.
Generator rotor bolt

80 Nm (8.0 mkg, 58 ftlb)
NOTE:
NOTE:
While holding the generator rotor 2 with a

sheave holder 3, tighten the generator rotor
bolt.

sheave holder 2, tighten the starter clutch
bolts.
Sheave holder
90890-01701
YS-01880-A
Sheave holder
90890-01701
YS-01880-A
3. Apply:
Sealant
(onto the stator coil lead grommet)
EAS24510
INSTALLING THE GENERATOR

1. Install:
Woodruff key
5-75

90890-85505
5-76
ELECTRIC STARTER
EAS24780
ELECTRIC STARTER
Removing the starter motor
1
2
T.
R.
Order
10 Nm (1.0 m kg, 7.2 ft Ib)
Job/Parts to remove
Qty
Starter motor lead
Starter motor
Remarks
Disconnect.
5-77
ELECTRIC STARTER
Disassembling the starter motor
LS
LS
New
New 3 2
New 4
10 New
New
11
12
7
6
8
New 10
9
5
Order
Job/Parts to remove
Qty
Starter motor front cover
Bearing
Oil seal
Circlip
Starter motor rear cover
Brush
Brush holder (along with the brushes)
Brush seat (along with the brushes)
Bearing
10
Gasket
11
Armature assembly
12
Starter motor yoke
Remarks
5-78
ELECTRIC STARTER
EAS24790
CHECKING THE STARTER MOTOR

1. Check:
Commutator
Dirt Clean with 600 grit sandpaper.
2. Measure:
Commutator diameter a
Out of specification Replace the starter
motor.
Pocket tester
90890-03112
YU-03112-C
Armature coil
Commutator resistance 1
0.00810.0099 at 20 C (68 F)
Insulation resistance 2
Above 1 M at 20 C (68 F)
Limit
27.5 mm (1.08 in)
3. Measure:
Mica undercut a
Out of specification Scrape the mica to the
proper measurement with a hacksaw blade
that has been grounded to fit the commutator.
Mica undercut (depth)
1.50 mm (0.06 in)
b. If any resistance is out of specification, replace the starter motor.
5. Measure:
Brush length a
Out of specification Replace the brushes
as a set.
Limit
5.00 mm (0.20 in)
NOTE:
The mica of the commutator must be undercut to

ensure proper operation of the commutator.
6. Measure:
Brush spring force
Out of specification Replace the brush
springs as a set.
4. Measure:
Armature assembly resistances (commutator
and insulation)
Out of specification Replace the starter
motor.
Brush spring force

7.3611.04 N (26.4939.74 oz)
(7501126 gf)
a. Measure the armature assembly resistances

with the pocket tester.
5-79
ELECTRIC STARTER
7. Check:
Gear teeth
Damage/wear Replace the gear.
8. Check:
Bearings
Oil seal
Damage/wear Replace the defective
part(s).
EAS24800
ASSEMBLING THE STARTER MOTOR

1. Install:
Starter motor yoke 1
NOTE:
Align the projection a on the brush holder with

the slot b in the starter motor yoke.
b
a
2. Install:
Starter motor front cover 1
NOTE:
Align the match mark a on the starter motor

yoke with the match mark b on the starter motor front cover.
5-80
TRANSFER GEAR CASE

EAS25460
TRANSFER GEAR CASE

Removing the middle driven shaft
T.
R.
18 Nm (1.8 m kg, 13 ft Ib)
(5)
T.
R.
8 Nm (0.8 m kg, 5.8 ft Ib)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
5 Nm (0.5 m kg, 3.6 ft Ib)
(7)
LT
New
LS
13
New
5
5
New
LS
4 New
7
12
New 1
11
9
2
T.
R.
10
10 Nm (1.0 m kg, 7.2 ft Ib)

E
New
T.
R.
New
140 Nm (14.0 m kg, 100 ft lb)
New
T.
R.
40 Nm (4.0 m kg, 29 ft Ib)

R.
R.
Order
T.
T.
10 Nm (1.0 m kg, 7.2 ft Ib)

Job/Parts to remove
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)

Remarks
Rider seat/Right side cover

4-1.
Engine oil
Drain.
page 3-11.
Transfer gear oil
Drain.
Refer to CHANGING THE TRANSFER
GEAR OIL on page 3-14.
Clutch release cylinder
Drive pulley
Oil pipe 2
Oil pipe 4
Transfer gear case cover
Transfer gear case gasket
Dowel pin
Transfer gear oil pump assembly
Dowel pin
5-81
TRANSFER GEAR CASE

Removing the middle driven shaft
T.
R.
18 Nm (1.8 m kg, 13 ft Ib)
(5)
T.
R.
8 Nm (0.8 m kg, 5.8 ft Ib)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
5 Nm (0.5 m kg, 3.6 ft Ib)
(7)
LT
New
LS
13
New
5
5
New
LS
4 New
7
12
New 1
11
9
2
T.
R.
10
10 Nm (1.0 m kg, 7.2 ft Ib)

E
New
T.
R.
New
140 Nm (14.0 m kg, 100 ft lb)
New
T.
R.
40 Nm (4.0 m kg, 29 ft Ib)

R.
R.
Order
T.
T.
10 Nm (1.0 m kg, 7.2 ft Ib)

Job/Parts to remove
Oil strainer
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)

Remarks
Gasket
10
11
Primary chain
12
Middle drive gear
13
Middle driven shaft
1
5-82
TRANSFER GEAR CASE

Disassembling the transfer gear oil pump
4
5
2
1
(6)
T.
R.
Order
4 Nm (0.4 m kg, 2.9 ft Ib)
Job/Parts to remove
Qty
Transfer gear oil pump cover
Transfer gear oil pump outer rotor
Transfer gear oil pump inner rotor
Pin
Washer
Transfer gear oil pump shaft
Transfer gear oil pump housing
Remarks
5-83
TRANSFER GEAR CASE

Removing the transfer gear case
(8)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
New
T.
10 Nm (1.0 m kg, 7.2 ft Ib)
R.
LS
LT
LS
1
4
2
New
New
5
LT
LS
T.
New
R.
70 Nm (7.0 m kg, 50 ft lb)
10
LS
E
E
New
LS
(4)
T.
R.
Order
50 Nm (5.0 m kg, 36 ft Ib)
Job/Parts to remove
Qty
Remarks
Horn 2 connector
Disconnect.
Battery box

4-1.
Sub-fuel tank
Oil tank breather hose
Speed sensor
Oil tank damper
Dipstick
Dipstick joint
Drive pulley case
Dowel pin
Spacer
Transfer gear case
10
Dowel pin
Disconnect.
5-84
TRANSFER GEAR CASE

Disassembling the oil tank
28 Nm (2.8 m kg, 20 ft Ib)
T.
R.
6
1
New
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LS
LT
LT
New
New
5
(15)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
43 Nm (4.3 m kg, 31 ft Ib)
3 New
2
Order
Job/Parts to remove
Qty
Sub-fuel tank bracket
Oil tank cover
Oil tank cover gasket
Dowel pin
Oil strainer
Oil pipe 5
Oil tank
Remarks
5-85
TRANSFER GEAR CASE

2. Check:
Primary chain
Damage/stiffness Replace the primary
chain, middle drive gear and middle driven
shaft as a set.
EAS25470
REMOVING THE MIDDLE DRIVEN SHAFT

NOTE:
Loosen the middle drive gear nut before remove

the drive pulley.
1. Install:
2. Loosen:
Middle drive gear nut 1
EAS25490
CHECKING THE OIL STRAINER

1. Check:
Oil strainer
Damage Replace.
Contaminants Clean with engine oil.
NOTE:
When loosening the middle drive gear nut, press

down on the brake pedal so the middle drive
gear does not move.
EAS25500
CHECKING THE TRANSFER GEAR OIL

PUMP
1. Check:
Transfer gear oil pump housing
Transfer gear oil pump cover
2. Measure:
Inner-rotor-to-outer-rotor-tip clearance a
b
Oil-pump-housing-to-inner-rotor-and-outerrotor clearance c
Out of specification Replace the transfer
gear oil pump.
3. Remove:
Primary chain 1
Middle drive gear 2
Middle driven shaft 3
NOTE:
Remove the primary chain, middle drive gear

and middle driven shaft at the same time.
1
3
2
EAS25480
CHECKING THE MIDDLE DRIVE

1. Check:
Middle drive gear
Middle driven gear
Damage/wear Replace the middle drive
gear, middle driven shaft and primary chain
as a set.
1. Transfer gear oil pump inner rotor

2. Transfer gear oil pump outer rotor
3. Transfer gear oil pump housing
5-86
TRANSFER GEAR CASE

Transfer gear oil pump outer rotor 6
Transfer gear oil pump cover 7
NOTE:
When installing the inner rotor, align the pin in

the oil pump shaft with the groove in the inner rotor.
T.
R.
Inner-rotor-to-outer-rotor-tip
clearance
Limit
0.20 mm (0.0079 in)
Outer-rotor-to-oil-pump-housing
clearance
0.100.15 mm (0.00390.0059 in)
Limit
0.22 mm (0.0087 in)
Oil-pump-housing-to-inner-andouter-rotor clearance
0.040.09 mm (0.00160.0035 in)
Limit
0.160 mm (0.0063 in)
Oil pump housing screw

4 Nm (0.4 mkg, 2.9 ftlb)
1
4
3. Check:
Transfer gear oil pump operation
Rough movement Repeat steps (1) and
(2) or replace the defective part(s).
(6)
3. Check:
Transfer gear oil pump operation
Refer to CHECKING THE TRANSFER
GEAR OIL PUMP on page 5-86.
EAS25530
INSTALLING THE TRANSFER GEAR CASE

1. Install:
Spacer 1
NOTE:
Install the spacer with its groove a towards the

drive pulley.
EAS25510
CHECKING THE OIL PIPES

1. Check:
Oil pipes
Damage Replace.
EAS25520
ASSEMBLING THE TRANSFER GEAR OIL

PUMP
1. Lubricate:
Transfer gear oil pump inner rotor
Transfer gear oil pump outer rotor
Transfer gear oil pump shaft
a
2. Install:
Middle driven shaft 1
Middle drive gear 2
Primary chain 3
(into the transfer gear case)
Drive pulley nut
Engine oil
2. Install:
Transfer gear oil pump shaft 1
(to the transfer gear oil pump housing 2)
Washer 3
Pin 4
Transfer gear oil pump inner rotor 5
NOTE:
Install the primary chain with its blue link a

facing outward.
5-87
TRANSFER GEAR CASE

Install the middle drive gear 2 with its chamfered side facing b the transfer gear case.
Install the middle driven shaft, middle drive
gear and primary chain at the same time.
Align the splines on the middle drive gear with
the splines on the drive axle.
Temporarily install the drive pulley nut onto the
middle driven shaft.
a
2 New
b
a
4. Remove:
Drive pulley nut
1
2
3. Install:
Middle drive gear nut 2 New
T.
R.
Middle drive gear nut

140 Nm (14.0 mkg, 100 ftlb)
NOTE:
Lubricate the middle drive gear nut threads

and conical spring washer mating surfaces
with engine oil.
Stake the middle drive gear nut 2 at a cutout
b in the drive axle.
5-88
CRANKCASE
EAS25540
CRANKCASE
Separating the crankcase
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

LT
LS
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
New
2
(5)
LT
LT
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
New
R.
T.
LS
R.
(4)
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
LT
New
9
3
3
(4)
(4)
11
(8)
LS
LS
12
13
LT
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
New
5
10
New
7
8
LS
T.
R.
New
(6)
LT
New
LT
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
43 Nm (4.3 m kg, 31 ft Ib)

T.
R.
Order
Job/Parts to remove
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)

Remarks
Engine
Camshafts
Pistons
Refer to CYLINDERS AND PISTONS on

page 5-45.
Shift shaft
Refer to SHIFT SHAFT on page 5-70.
Generator rotor
Refer to GENERATOR AND STARTER

CLUTCH on page 5-72.
Neutral switch
Oil pipe 3
Oil strainer
Oil delivery pipe 3
Engine oil pump driven gear stopper
Oil baffle plate (left crankcase)
Left crankcase
Dowel pin
5-89
CRANKCASE
Separating the crankcase
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)

LT
LS
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
R.
New
2
(5)
LT
LT
10 Nm (1.0 m kg, 7.2 ft Ib)
T.
New
R.
T.
LS
R.
(4)
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
LT
New
9
3
3
(4)
(4)
11
(8)
LS
LS
12
13
LT
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
New
5
10
New
7
8
LS
T.
R.
New
(6)
LT
New
LT
10 Nm (1.0 m kg, 7.2 ft Ib)

T.
R.
43 Nm (4.3 m kg, 31 ft Ib)

T.
R.
Order
Job/Parts to remove
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)

Remarks
10
Joint pipe
11
Oil pipe
R mark
12
Oil pipe
F mark
13
Right crankcase
1
5-90
CRANKCASE
Removing the oil seals and bearings
LS
New 4
LS
5
E
LT
LT
New
T.
R.
20 Nm (2.0 m kg, 14 ft Ib)
New
LT
5
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
LT
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
3
E
LT
Order
Job/Parts to remove
Qty
Oil pump
Remarks
Refer to OIL PUMP on page 5-95.
Crankshaft
Refer to CRANKSHAFT on page 5-101.
Transmission
Refer to TRANSMISSION on page 5-107.
Oil baffle plate (right crankcase)
Bearing retainer
Bearing retainer
Oil seal
Bearing
4
5-91
CRANKCASE
EAS25570
DISASSEMBLING THE CRANKCASE

1. Remove:
Crankcase bolts
NOTE:
Loosen each bolt 1/4 of a turn at a time, in stages and in a crisscross pattern. After all of the
bolts are fully loosened, remove them.
Loosen the bolts in decreasing numerical order
(refer to the numbers in the illustration).
M8 90 mm bolts: 1, 2
M8 65 mm bolt: 3
M6 100 mm bolts: 4, 911
M6 80 mm bolt: 12
M6 70 mm bolts: 1316
M6 60 mm bolts: 58
A
EAS25580
CHECKING THE CRANKCASE

1. Thoroughly wash the crankcase halves in a
mild solvent.
2. Thoroughly clean all the gasket surfaces and
crankcase mating surfaces.
3. Check:
Crankcase
Oil delivery passages
1
3
ET1D71005
CHECKING THE BEARINGS AND OIL SEAL

1. Check:
Bearings
Clean and lubricate the bearings, then rotate
the inner race with your finger.
Rough movement Replace.
Oil seals
4
B
13
11
24
EAS25590
CHECKING THE OIL DELIVERY PIPE AND

OIL PIPE
1. Check:
Oil delivery pipe
Oil pipes
Damage Replace.
12
23
17
22
21
20 16 15 10 14 19
18
A. Right crankcase
B. Left crankcase
2. Remove:
Left crankcase
ET1D71038
CHECKING THE OIL STRAINERS

1. Check:
Oil strainers
Damage Replace.
Contaminants Clean with solvent.
ECA13900
CAUTION:
Tap on one side of the crankcase with a softface hammer. Tap only on reinforced portions of the crankcase, not on the crankcase
mating surfaces. Work slowly and carefully
and make sure the crankcase halves separate evenly.
5-92
CRANKCASE
Joint pipe 4
EAS25610
CHECKING THE ENGINE OIL PUMP DRIVEN

GEAR
1. Check:
Chips/pitting/roughness/wear Replace.
2
3
ET1D71034
INSTALLING THE BEARING RETAINERS

1. Install:
Bearing retainers 1
4
3
NOTE:
3. Install:
Left crankcase
(onto the right crankcase)

of the bearing retainer bolts.
Stake the bearing retainer bolts 2.
NOTE:
Tap lightly on the left crankcase with a soft-face

hammer.
2 1
4. Install:
Crankcase bolts (M6)
Crankcase bolts (M8)
T.
1
2
R.
Crankcase bolt (M6)

10 Nm (1.0 mkg, 7.2 ftlb)
Crankcase bolt (M8)
24 Nm (2.4 mkg, 17 ftlb)
EAS25690
ASSEMBLING THE CRANKCASE

1. Apply:
Sealant
(onto the crankcase mating surfaces)
NOTE:
Lubricate the bolt threads with engine oil.

Tighten each bolt 1/4 of a turn at a time, in stages and in a crisscross pattern.
Tighten the bolts in numerical order (refer to
the numbers in the illustration).

90890-85505
M8 90 mm bolts: 1, 2
M8 65 mm bolt: 3
M6 100 mm bolts: 4, 911
M6 80 mm bolt: 12
M6 60 mm bolts: 58
NOTE:
Do not allow any sealant to come into contact

with the oil gallery.
2. Install:
Oil pipe (F mark) 1
Oil pipe (R mark) 2
Dowel pins 3
5-93
CRANKCASE
A
1
3
4
B
13
11
24
12
23
22
21
20 16 15 10 14 19
17
18
A. Right crankcase
B. Left crankcase
5. Apply:
Engine oil
(onto the crankshaft pin bearings and oil delivery holes)
6. Check:
Crankshaft and transmission operation
5-94
OIL PUMP
EAS24910
OIL PUMP
Removing the oil pump
T.
R.
24 Nm (2.4 m kg, 17 ft Ib)
Order
Job/Parts to remove
Qty
Separate.
Refer to CRANKCASE on page 5-89.
Crankcase
1
Remarks
Oil pump assembly
1
5-95
OIL PUMP
Disassembling the oil pump
5
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
3
2
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
12
15
16
18 17
11
19 New
24
7
10
New 20
22
New 21
9
23
13
7
14
8
Order
Job/Parts to remove
Qty
Oil pump housing cover 1
Oil scavenging pump outer rotor 1
Oil scavenging pump inner rotor 1
Pin
Oil pump housing 1
Oil strainer
Pin
Ball spring
Oil scavenging pump outer rotor 2
10
Oil scavenging pump inner rotor 2
11
Pin
12
Oil pump housing cover 2
13
Relief valve spring
14
Relief valve
15
Oil feed pump outer rotor
16
Oil feed pump inner rotor
17
Pin
5-96
Remarks
OIL PUMP
Disassembling the oil pump
5
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
3
2
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
12
15
16
18 17
11
19 New
24
7
10
New 20
22
New 21
9
23
13
7
14
8
Order
18
Job/Parts to remove
Qty
Oil pump shaft
19
Oil seal
20
Circlip
21
Oil seal
22
Ball
23
Ball guide
24
Oil pump housing 2
Remarks
5-97
OIL PUMP
3. Check:
Oil pump operation
Rough movement Repeat steps (1) and
(2) or replace the defective part(s).
EAS24960
CHECKING THE OIL PUMP

1. Check:
Oil pump housing
Oil pump housing cover
2. Measure:
Inner-rotor-to-outer-rotor-tip clearance a
b
Oil-pump-housing-to-inner-rotor-and-outerrotor clearance c
Out of specification Replace the oil pump.
Inner-rotor-to-outer-rotor-tip
clearance
Limit
0.20 mm (0.0079 in)
Oil-pump-housing-to-inner-andouter-rotor clearance
0.060.13 mm (0.00240.0051 in)
Limit
0.20 mm (0.0079 in)
Outer-rotor-to-oil-pump-housing
clearance
0.090.19 mm (0.00350.0075 in)
Limit
0.26 mm (0.0102 in)
EAS24970
CHECKING THE RELIEF VALVE

1. Check:
Relief valve body
Relief valve
Relief valve spring
Damage/wear Replace the defective
part(s).
ET1D71035
CHECKING THE BALL SPRING AND RELIEF

VALVE SPRING
1. Measure:
Ball spring free length
Relief valve spring free length
part(s).
Ball spring
Free length
34.70 mm (1.37 in)
Limit
32.97 mm (1.30 in)
Relief valve spring
Free length
28.95 mm (1.14 in)
Limit
27.50 mm (1.08 in)
1. Inner rotor
2. Outer rotor
3. Oil pump housing
a. Free length
5-98
OIL PUMP
Oil pump shaft
2. Measure:
Ball spring force
Relief valve spring force
part(s).
Engine oil
2. Install:
Oil pump housing 2 1
Ball guide 2
Ball 3
Ball spring
force
2.23 N (0.60 lb) (0.27 kgf) or less
Installed length
29.4 mm (1.12 in)
Relief valve spring
force
52.4 N (11.78 lb) (5.34 kgf) or
less
Installed length
16.8 mm (0.66 in)
Oil seal 4 New

Circlip 5 New
Oil seal 6 New
Oil pump shaft 7
Pin 8
Oil feed pump inner rotor 9
Oil feed pump outer rotor 10
Relief valve 11
Relief valve spring 12
Oil pump housing cover 2 13
T.
R.

7 Nm (0.7 mkg, 5.1 ftlb)
Pin 14
Oil scavenging pump inner rotor 2 15
Oil scavenging pump outer rotor 2 16
Ball spring 17
Pins 18
Oil strainer 19
Oil pump housing 1 20
Pin 21
Oil scavenging pump inner rotor 1 22
Oil scavenging pump outer rotor 1 23
Oil pump housing cover 1 24
a. Spring force
b. Installed length
EAS24990
T.
CHECKING THE OIL STRAINER

1. Check:
Oil strainer 1
Damage Replace.
Contaminants Clean with solvent.
R.

7 Nm (0.7 mkg, 5.1 ftlb)
NOTE:
When installing the inner rotor, align the pin in

the oil pump shaft with the groove in the inner rotor.
EAS25000
ASSEMBLING THE OIL PUMP

1. Lubricate:
Inner rotor
Outer rotor
5-99
OIL PUMP
20
22
23
24
19
13
10
78
14 21
New 5
New 4
6 New
1
18 E
15
16
3 2
12
11
18
17
3. Check:
Oil pump operation
Refer to CHECKING THE OIL PUMP on
page 5-98.
EAS25020
INSTALLING THE OIL PUMP

1. Install:
Oil pump assembly 1
T.
R.
Oil pump assembly bolt

24 Nm (2.4 mkg, 17 ftlb)
ECA13890
CAUTION:
After tightening the bolts, make sure the oil

pump turns smoothly.
5-100
CRANKSHAFT
EAS25960
CRANKSHAFT
Removing the crankshaft
Order
Job/Parts to remove
Qty
Separate.
Crankcase
1
Remarks
Crankshaft
Generator shaft
Connecting rod cap
Big end lower bearing
Connecting rod
Big end upper bearing
2
5-101
CRANKSHAFT
EAS26010
REMOVING THE CONNECTING RODS

1. Remove:
Connecting rod caps 1
Connecting rods
Big end bearings
NOTE:
Identify the position of each big end bearing so

that it can be reinstalled in its original place.
3. Measure:
Crankshaft-pin-to-big-end-bearing clearance
Out of specification Replace the big end
bearings.
Journal oil clearance (using plastigauge)
0.0300.060 mm (0.00120.0024
in)
connecting rods.
EAS26090
CHECKING THE CRANKSHAFT AND

CONNECTING RODS
1. Measure:
Crankshaft runout
Out of specification Replace the crankshaft.
Runout limit C
0.040 mm (0.0016 in)
ECA13930
CAUTION:
Do not interchange the big end bearings and

connecting rods. To obtain the correct
crankshaft-pin-to-big-end-bearing clearance and prevent engine damage, the big
end bearings must be installed in their original positions.
a. Clean the big end bearings, crankshaft pins,

and the inside of the connecting rod halves.
b. Install the big end upper bearing into the connecting rod and the big end lower bearing into
the connecting rod cap.
NOTE:
Align the projections a on the big end bearings

with the notches b in the connecting rod and
connecting rod cap.
2. Check:
Crankshaft journal surfaces
Crankshaft pin surfaces
Bearing surfaces
Scratches/wear Replace the crankshaft.
Generator shaft drive gear 1
Damage/wear Replace the crankshaft.
c. Put a piece of Plastigauge 1 on the crankshaft pin.
5-102
CRANKSHAFT
d. Assemble the connecting rod halves.
h. Tighten the connecting rod bolts further to

reach the specified angle 125135.
NOTE:
T.
Do not move the connecting rod or crankshaft

until the clearance measurement has been
completed.
Lubricate the bolts threads with molybdenum
disulfide grease.
Make sure the projection c on the connecting
rod faces towards the left side of the crankshaft.
Make sure the characters d on both the connecting rod and connecting rod cap are
aligned.
R.

EW1D71011
WARNING
When a bolt is tightened more than the specified angle, do not loosen and then retighten
it.
Replace the bolt with a new one and perform
the procedure again.
EC1D71001
CAUTION:
e. Tighten the connecting rod bolts.

EWA12890
WARNING
Replace the connecting rod bolts with new

ones.
Clean the connecting rod bolts.
NOTE:
The tightening procedure of the connecting rod

bolts is angle controlled, therefore tighten the
bolts using the following procedure.
f. Tighten the connecting rod bolts to the specified torque.
Do not use a torque wrench to tighten the

bolt to the specified angle.
Tighten the bolt until it is at the specified
angle.
i. Remove the connecting rod and big end
bearings.
j. Measure the compressed Plastigauge width
e on the crankshaft pin.
If the crankshaft-pin-to-big-end-bearing
clearance is out of specification, select replacement big end bearings.
T.
R.

15 Nm (1.5 mkg, 11 ftlb)
g. Put a mark 1 on the connecting rod bolts 2

and the connecting rod cap 3.
5-103
CRANKSHAFT
For example, if the connecting rod P1 and
the crankshaft web P numbers are 5 and
2 respectively, then the bearing size for P1
is:
P1 (connecting rod) - P (crankshaft)
=
5 - 2 = 3 (brown)
Bearing color code
1.Blue 2.Black 3.Brown 4.Green
5.Yellow
4. Select:
Big end bearings (P1P2)
NOTE:
The numbers a stamped into the crankshaft

web and the numbers b on the connecting
rods are used to determine the replacement
big end bearing sizes.
P1P2 refer to the bearings shown in the
crankshaft illustration.
P1
5. Measure:
Crankshaft journal diameter a
Out of specification Replace the crankshaft.
NOTE:
Measure the diameter of each crankshaft journal

at two places.
Crankshaft journal diameter
49.96849.980 mm (1.9672
1.9677 in)
P2
a
6. Measure:
Crankshaft journal bearing inside diameter
a
Out of specification Replace the crankcase assembly.
NOTE:
Measure the inside diameter of each crankshaft

journal bearing at two places.
Crankshaft journal bearing inside
diameter
50.01050.030 mm (1.9689
1.9697 in)
5-104
CRANKSHAFT
Be sure to reinstall each big end bearing in its
original place.
Make sure the projection c on the connecting
rods face towards the left side of the crankshaft.
Make sure the characters d on both the connecting rod and connecting rod cap are
aligned.
7. Calculate:
Crankshaft journal-to-crankshaft journal
bearing clearance
Out of specification Replace the crankshaft and crankshaft journal bearings as a
set.
NOTE:
Calculate the clearance by subtracting the

crankshaft journal diameter from the crankshaft
journal bearing inside diameter.
Crankshaft journal-to-crankshaft
journal bearing clearance
0.0300.060 mm (0.00120.0024
in)
EAS26150
INSTALLING THE CONNECTING RODS

1. Lubricate:
Bolt threads
4. Tighten:
Connecting rod bolts 1
Molybdenum disulfide grease
2. Lubricate:
Crankshaft pins
Big end bearings
Connecting rod inner surface
Engine oil
EWA12890
WARNING
3. Install:
Big end bearings
Connecting rods
Connecting rod caps
(onto the crankshaft pins)
Replace the connecting rod bolts with new

ones.
Clean the connecting rod bolts.
NOTE:
NOTE:
Align the projections a on the big end bearings with the notches b in the connecting rods
and connecting rod caps.
The tightening procedure of the connecting rod

bolts is angle controlled, therefore tighten the
bolts using the following procedure.
5-105
CRANKSHAFT
a. Tighten the connecting rod bolts with a torque
wrench.
T.
R.

15 Nm (1.5 mkg, 11 ftlb)
b. Put a mark 1 on the corner of the connecting

rod bolts 2 and the connecting rod 3.
Crankshaft assembly 2
ECA13970
CAUTION:
To avoid scratching the crankshaft and to

ease the installation procedure, lubricate the
oil seal lips with lithium-soap-based grease
and each bearing with engine oil.
NOTE:
Make sure that the generator shaft drive gear

teeth and generator shaft driven gear teeth
mesh correctly.
Align the punch mark a on the generator shaft
driven gear with the punch mark b on the generator shaft drive gear.
Align the right connecting rod with the front cylinder sleeve hole.
c. Tighten the connecting rod bolts further to
reach the specified angle 125135.
T.
R.

1
2
EW1D71011
WARNING
When a bolt is tightened more than the specified angle, do not loosen and then retighten
it.
Replace the bolt with a new one and perform
the procedure again.
EC1D71001
CAUTION:
Do not use a torque wrench to tighten the

bolt to the specified angle.
Tighten the bolt until it is at the specified
angle.
EAS26210
INSTALLING THE CRANKSHAFT

ASSEMBLY
1. Install:
Generator shaft 1
5-106
TRANSMISSION
EAS26240
TRANSMISSION
Removing the transmission, shift drum assembly, and shift forks
New
LS
7
3
1
3
M
E
4
E
Order
Job/Parts to remove
Qty
Remarks
Separate.
Crankcase
1
Shift fork guide bar
Shift drum assembly
Shift fork 1
Shift fork 2
Drive axle assembly
Main axle assembly
Spacer
1
5-107
TRANSMISSION
Disassembling the main axle assembly
Order
Job/Parts to remove
Qty
2nd pinion gear
Toothed lock washer
Toothed lock washer retainer
5th pinion gear
Collar
Toothed washer
Circlip
3rd pinion gear
Circlip
10
Toothed washer
11
4th pinion gear
12
Collar
13
Main axle/1st pinion gear
Remarks
5-108
TRANSMISSION
Disassembling the drive axle assembly
Order
1
Job/Parts to remove
Qty
Circlip
Washer
1st wheel gear
Collar
4th wheel gear
Circlip
Toothed washer
3rd wheel gear
Collar
10
Toothed lock washer
11
Toothed lock washer retainer
12
5th wheel gear
13
Circlip
14
Toothed washer
15
2nd wheel gear
16
Collar
5-109
Remarks
TRANSMISSION
Disassembling the drive axle assembly
Order
17
Job/Parts to remove
Qty
Drive axle
Remarks
1
5-110
TRANSMISSION
EAS26260
EAS26270
CHECKING THE SHIFT FORKS

The following procedure applies to all of the shift
forks.
1. Check:
Shift fork cam follower 1
Shift fork pawl 2
Bends/damage/scoring/wear Replace the
shift fork.
CHECKING THE SHIFT DRUM ASSEMBLY

1. Check:
Shift drum groove
Damage/scratches/wear Replace the shift
drum assembly.
Shift drum segment 1
Damage/wear Replace the shift drum assembly.
Shift drum bearing 2
Damage/pitting Replace the shift drum assembly.
2. Check:
Shift fork guide bar
Roll the shift fork guide bar on a flat surface.
Bends Replace.
EAS26300
EWA12840
WARNING
Do not attempt to straighten a bent shift fork

guide bar.
CHECKING THE TRANSMISSION

1. Measure:
Main axle runout
(with a centering device and dial gauge 1)
Out of specification Replace the main axle.
Main axle runout limit
0.08 mm (0.0032 in)
3. Check:
Shift fork movement
(along the shift fork guide bar)
Rough movement Replace the shift forks
and shift fork guide bar as a set.
2. Measure:
Drive axle runout
(with a centering device and dial gauge 1)
Out of specification Replace the drive axle.
Drive axle runout limit
0.08 mm (0.0032 in)
5-111
TRANSMISSION
Install the circlip so that both ends b rest on
the sides of a spline c with both axles aligned.
2 New
3. Check:
Transmission gears
Blue discoloration/pitting/wear Replace
the defective gear(s).
Transmission gear dogs
Cracks/damage/rounded edges Replace
the defective gear(s).
c
2. Install:
Toothed lock washer retainer 1
Toothed lock washer 2
NOTE:
4. Check:
Transmission gear engagement
(each pinion gear to its respective wheel
gear)
Incorrect Reassemble the transmission
axle assemblies.
5. Check:
Transmission gear movement
Rough movement Replace the defective
part(s).
6. Check:
Circlips
Bends/damage/looseness Replace.
With the toothed lock washer retainer 1 in the

groove a in the axle, align the projection c
on the retainer with an axle spline b, and then
install the toothed lock washer 2.
Be sure to align the projection on the toothed
lock washer that is between the alignment
marks e with the alignment mark d on the
retainer.
1
c
b e
ET1D71006
ASSEMBLING THE MAIN AXLE AND DRIVE

AXLE
1. Install:
Toothed washer 1
2
1
Circlip 2 New
EAS26320
NOTE:
Be sure the circlip sharp-edged corner a is

positioned opposite side to the toothed washer
and gear. (For main axle)
INSTALLING THE SHIFT FORKS AND SHIFT

DRUM ASSEMBLY
1. Install:
Shift forks 1 1
Shift fork 2 2
Shift drum assembly 3
5-112
TRANSMISSION
Shift fork guide bars 4
NOTE:
The embossed marks 1D7 on the shift forks

should face towards the left side of the engine.
4
2
4
1
2. Check:
Transmission
NOTE:
Apply engine oil to each gear and bearing thoroughly.

Before assembling the crankcase, make sure
that the transmission is in neutral and that the
gears turn freely.
5-113
FUEL SYSTEM
FUEL TANK .................................................................................................... 6-1
REMOVING THE FUEL TANK.................................................................. 6-3
REMOVING THE FUEL PUMP ................................................................. 6-3
CHECKING THE FUEL PUMP BODY ...................................................... 6-4
CHECKING THE FUEL PUMP OPERATION ........................................... 6-4
INSTALLING THE FUEL PUMP................................................................ 6-4
INSTALLING THE FUEL TANK ................................................................ 6-4
THROTTLE BODIES....................................................................................... 6-6
REMOVING THE FUEL HOSE ............................................................... 6-11
CHECKING THE INJECTORS................................................................ 6-11
CHECKING THE THROTTLE BODIES................................................... 6-11
CHECKING THE ROLLOVER VALVES.................................................. 6-11
CHECKING THE PRESSURE REGULATOR ......................................... 6-11
CHECKING THE PRESSURE REGULATOR OPERATION................... 6-11
ADJUSTING THE THROTTLE POSITION SENSOR ............................. 6-12
INSTALLING THE FUEL PIPE................................................................ 6-12
INSTALLING THE FUEL HOSE.............................................................. 6-13
ISC (IDLE SPEED CONTROL) UNIT............................................................ 6-14
CHECKING THE ISC (IDLE SPEED CONTROL) SYSTEM ................... 6-15
FUEL TANK
EAS26620
FUEL TANK
Removing the fuel tank
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
6
1
T.
R.
T.
R.
16 Nm (1.6 m kg, 11 ft Ib)
10 Nm (1.0 m kg, 7.2 ft Ib)
(4)
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
R.
T.
R.
4 Nm (0.4 m kg, 2.9 ft Ib)
3
5
Order
Job/Parts to remove
Qty
Remarks
4-1.
Rider seat/Rider seat bracket

1
Meter assembly coupler
Disconnect.
Meter cover
Fuel sender coupler
Disconnect.
Fuel tank breather hose
Disconnect.
Air vent hose (fuel pump to fuel hose joint)
Disconnect.
Fuel tank
Fuel tank bracket (rear side)
Fuel tank bracket (front side)
Fuel sender
1
6-1
FUEL TANK
Removing the fuel pump and sub-fuel tank
4
T.
R.
5 Nm (0.5 m kg, 3.6 ft Ib)
5
3
New
(6)
6
7
New
8
(3)
(3)
(3)
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
Order
Job/Parts to remove
Qty
Remarks

4-1.
Fuel tank
Fuel pump coupler
Fuel hose connector cover
Fuel outlet hose
Air vent hose (fuel pump to fuel hose joint)
Fuel return hose (fuel return pipe to sub-fuel

tank)
Fuel pump bracket
Fuel pump gasket
Fuel pump
Sub-fuel tank
Disconnect.
Disconnect.
Disconnect.
6-2
FUEL TANK
EAS26630
REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the
fuel tank cap with a pump.
2. Remove:
Fuel tank
EC1D71021
CAUTION:
Although the fuel has been removed from

the fuel tank, be careful when removing the
fuel hoses, since there may be fuel remaining in them.
d. Disconnect the fuel hose (fuel hose joint to

fuel pump) 1 and air vent hose (fuel pump to
fuel hose joint) 2.
a. Remove the fuel hose joint caps 1.
NOTE:
NOTE:
Before removing the hoses, place a few rags in

the area under where they will be removed.
After removing the fuel hose joint caps, clean the

projection on each cap so that no foreign material will enter the fuel lines.
2
1
1
e. Install the fuel hose joint cap 1 and rubber

plug 2.
b. Lubricate the O-ring 1 with the recommended silicone lubricant 2.
NOTE:
Insert the projection on the fuel hose joint cap

completely into the pipe of the fuel hose joint and
insert the rubber plug into the end of the fuel
hose (fuel hose joint to fuel pump).
Silicone protectant and lubricant
ACC-SLCNS-PR-AY
NOTE:
Spray the silicone lubricant in the areas shown in

the illustration.
2
1
f. Remove the fuel tank.
EAS26640
REMOVING THE FUEL PUMP

1. Remove:
Fuel hose connector cover
2. Disconnect:
Fuel outlet hose
c. Turn the screws 1 clockwise.

NOTE:
Turn the screws until they stop.
6-3
FUEL TANK
Install the fuel pump as shown in the illustration.
Align the projection a on the fuel pump with
the slot in the fuel pump bracket.
Tighten the fuel pump bolts in the proper tightening sequence as shown.
EC1D71022
CAUTION:
Be sure to disconnect the fuel outlet hose

by hand. Do not forcefully disconnect the
hose with tools.
the fuel tank be careful when removing the
fuel hoses, since there may be fuel remaining in them.
NOTE:
Remove the fuel hose manually without using

any tools.
3. Remove:
Fuel pump
2. Connect:
Fuel outlet hose
3. Install:
Fuel hose connector cover 1
ECA14720
CAUTION:
Do not drop the fuel pump or give it a

strong shock.
Do not touch the base section of the fuel
sender.
EC1D71023
CAUTION:
When installing the fuel outlet hose, make

sure that it is securely connected, and that
the fuel hose connector cover is installed
correctly, otherwise the fuel outlet hose will
not be properly installed.
EAS26670
CHECKING THE FUEL PUMP BODY

1. Check:
Fuel pump body
Obstruction Clean.
Cracks/damage Replace fuel pump assembly.
2. Check:
Diaphragms and gaskets
Tears/fatigue/cracks Replace fuel pump
assembly.
NOTE:
Install the fuel outlet hose connector securely

onto the sub fuel tank until a distinct click is
heard, and then make sure that it does not
come loose.
Install the holder a of the fuel hose connector
cover, and then install the holder b. After installing the fuel hose connector cover, make
sure that it is installed securely.
EAS26690
CHECKING THE FUEL PUMP OPERATION

1. Check:
Fuel pump operation
Refer to CHECKING THE FUEL PUMP on
page 7-89.
1
a
EAS26710
INSTALLING THE FUEL PUMP

1. Install:
Fuel pump
T.
R.
Fuel pump bolt

5 Nm (0.5 mkg, 3.6 ftlb)
ET1D71025
INSTALLING THE FUEL TANK

1. Install:
Fuel tank
NOTE:
Do not damage the installation surfaces of the

sub-fuel tank when installing the fuel pump.
Always use a new fuel pump gasket.
6-4
FUEL TANK
a. Install the fuel tank.

b. Remove the fuel hose joint caps.
c. Connect the fuel hose (fuel hose joint to fuel
pump) and air vent hose (fuel pump to fuel
hose joint).
d. Turn the screws 1 counterclockwise.
NOTE:
Turn the screws until they contact the clips a.
1
1
a
a
e. Install the fuel hose joint caps.
NOTE:
Install the fuel hose joint caps completely onto

the fuel hose joints.
2. Install:
Meter assembly couplers
Fuel sender coupler
NOTE:
Make sure that the couplers are positioned as

shown in the illustration in the following order
from left to right: fuel sender coupler 1, 6-pin
black meter assembly coupler 2, 4-pin white
meter assembly coupler 3, and 6-pin white
meter assembly coupler 4.
4
3
2
1
6-5
THROTTLE BODIES
EAS26970
THROTTLE BODIES
Removing the rollover valves
4
7
7
1
6
7
7
8
9
10
T.
7 Nm (0.7 m kg, 5.1 ft Ib)
R.
T.
R.
Order
Job/Parts to remove
Qty
10 Nm (1.0 m kg, 7.2 ft Ib)
Remarks
Horn 1 connector
For California only

Disconnect.
Horn 1
For California only
Fuel tank breather hose
Canister purge hose
Rollover valve 1
Rollover valve 2
Rollover valve hose
Fuel tank breather/overflow hose
Canister
For California only
10
Canister breather hose
For California only
For California only
6-6
THROTTLE BODIES
Removing the pressure regulator
8
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
T.
R.
13 Nm (1.3 m kg, 9.4 ft Ib)
7
2
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
6
1
Order
Job/Parts to remove
Qty
Pressure regulator cover
Fuel hose (intake manifold assembly to pressure regulator)
Hose clamp
Pressure regulator
Fuel return hose
Fuel return pipe
Pressure regulator bracket
Remarks
6-7
THROTTLE BODIES
Removing the throttle bodies
5
T.
R.
3 Nm (0.3 m kg, 2.2 ft Ib)
3
2
6
6
T.
R.
3 Nm (0.3 m kg, 2.2 ft Ib)
Order
Job/Parts to remove
Qty
Remarks

4-1.
Fuel tank
Air filter case

4-1.
Throttle position sensor coupler
Disconnect.
Canister purge hose
For California only
Throttle cable
Disconnect.
Throttle body joint clamp screw
Loosen.
EC1D71013
CAUTION:
7
Throttle body
The throttle bodies should not be disassembled.
6-8
THROTTLE BODIES
Removing the intake manifolds
3
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
5
(2)
New 8
2
(2)
4
7
New 8
T.
R.
10 Nm (1.0 m kg, 7.2 ft Ib)
Order
Job/Parts to remove
Qty
Remarks
Engine temperature sensor coupler
Disconnect.
Disconnect.
Fuel outlet hose
Disconnect.

hose
Disconnect.

hose
Disconnect.
Intake manifold assembly
Gasket
2
6-9
THROTTLE BODIES
Disassembling the intake manifolds
.
R.
30 Nm (3.0 m kg, 22 ft Ib)
New
New
T.
R.
5 Nm (0.5 m kg, 3.6 ft Ib)
4
5
New
New
New
New
2
1
New
New
7
6
T.
R.
Order
5 Nm (0.5 m kg, 3.6 ft Ib)
Job/Parts to remove
Cylinder-#1 injector coupler
2
3
Qty
Remarks
Disconnect.
Cylinder-#2 injector coupler
Disconnect.
Sub-wire harness 2
Fuel pipe
Injector joint 1
Injector joint 2
Injector
2
6-10
THROTTLE BODIES
b. Blow out all of the passages with compressed
air.
ET1D71026
REMOVING THE FUEL HOSE

1. Disconnect:
ET1D71007
CHECKING THE ROLLOVER VALVES

1. Check:
Rollover valve 1 1
Rollover valve 2 2
Damage/faulty Replace.
EC1D71014
CAUTION:

the fuel tank be careful when removing the
fuel hose, since there may be fuel remaining
in it.
NOTE:
Check that air flows smoothly only in the direction of the arrow shown in the illustration.
The rollover valves must be in an upright position when checking the airflow.
NOTE:
To remove the fuel hose from the fuel pipe or

pressure regulator, slide the fuel hose connector cover 1 on the end of the hose in the direction of the arrow shown, press the two buttons
2 on the sides of the connector, and then remove the hose.
Remove the fuel hose manually without using
any tools.
EAS27000
CHECKING THE PRESSURE REGULATOR

1. Check:
Pressure regulator
Damage Replace.
2
EAS27010
CHECKING THE PRESSURE REGULATOR

OPERATION
1. Check:
Pressure regulator operation
EAS26980
CHECKING THE INJECTORS

1. Check:
Injectors
Damage Replace.
a. Remove the pressure regulator cover.

b. Disconnect the fuel hose 1 from the pressure regulator 2.
c. Connect the fuel pressure adapter 3 between the fuel hose 1 and pressure regulator 2.
d. Connect the pressure gauge 4 to the fuel
pressure adapter 3.
e. Connect the vacuum/pressure pump gauge
set 5 to the pressure regulator.
EAS26990
CHECKING THE THROTTLE BODIES

1. Check:
Throttle bodies
Cracks/damage Replace the throttle bodies as a set.
2. Check:
Fuel passages
Obstructions Clean.
a. Wash the throttle bodies in a petroleumbased solvent.

Do not use any caustic carburetor cleaning
solution.
6-11
THROTTLE BODIES
EAS27030
ADJUSTING THE THROTTLE POSITION

SENSOR
1. Check:
Refer to CHECKING THE THROTTLE POSITION SENSOR on page 7-89.
2. Adjust:
Throttle position sensor angle
Vacuum/pressure pump gauge

set
90890-06756
Pressure gauge
90890-03153
Fuel pressure adapter
90890-03176
YM-03176
a. Connect the throttle position sensor coupler

to the throttle position sensor.
b. Connect the digital circuit tester to the throttle
position sensor.
Positive tester probe
yellow terminal 1
Negative tester probe
black terminal 2
1
2
Digital circuit tester

90890-03174
Model 88 Multimeter with tachometer
YU-A1927
1
4
c. Measure the throttle position sensor voltage.

d. Adjust the throttle position sensor angle so
that the voltage is within the specified range.
5
2
3
Output voltage (at idle)

0.630.73 V
f. Start the engine.

g. Measure the fuel pressure.
e. After adjusting the throttle position sensor angle, tighten the throttle position sensor
screws 3.
Fuel pressure
392 kPa (3.92 kg/cm, 55.7 psi)
h. Use the vacuum/pressure pump gauge set to
adjust the fuel pressure in relation to the vacuum pressure as described below.
NOTE:
The vacuum pressure should not exceed 100

kPa (760 mmHg).
Increase the vacuum pressure

Fuel pressure is decreased
Decrease the vacuum pressure
Fuel pressure is increased
ET1D71008
INSTALLING THE FUEL PIPE

1. Install:
Fuel pipe 1
Faulty Replace the pressure regulator.
T.
R.
6-12
Fuel pipe bolt

30 Nm (3.0 mkg, 22 ftlb)
THROTTLE BODIES
NOTE:
Install the fuel pipe 1 so that it contacts the projections a on the injector joints.
1
a
1
a
ET1D71027
INSTALLING THE FUEL HOSE

1. Connect:
EC1D71015
CAUTION:
When installing the fuel hose, make sure that

it is securely connected, and that the fuel
hose connector cover on the fuel hose is in
the correct position, otherwise the fuel hose
will not be properly installed.
NOTE:
Install the fuel hose securely onto the fuel pipe

or pressure regulator until a distinct click is
heard.
To install the fuel hose onto the fuel pipe or
pressure regulator, slide the fuel hose connector cover 1 on the end of the hose in the direction of the arrow shown.
6-13
ISC (IDLE SPEED CONTROL) UNIT

ET1D71009

Removing the ISC (idle speed control) unit
T.
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
1
8
(4)
T.
R.
7 Nm (0.7 m kg, 5.1 ft Ib)
5
T.
R.
Order
7 Nm (0.7 m kg, 5.1 ft Ib)
Job/Parts to remove
Qty
Front cylinder head
Remarks
Sub-wire harness 4
Sub-wire harness 3

hose

hose
Cylinder-#2 left ignition coil
Cylinder-#2 right ignition coil
ISC (idle speed control) unit bracket
1
6-14

ET1D71010
CHECKING THE ISC (IDLE SPEED

CONTROL) SYSTEM
1. Check:
Hoses
Loose connections Connect properly.
6-15
ELECTRICAL SYSTEM
IGNITION SYSTEM ......................................................................................... 7-1
CIRCUIT DIAGRAM .................................................................................. 7-1
ENGINE STOPPING DUE TO SIDESTAND OPERATION....................... 7-3
TROUBLESHOOTING .............................................................................. 7-4
ELECTRIC STARTING SYSTEM.................................................................... 7-7
CIRCUIT DIAGRAM .................................................................................. 7-7
STARTING CIRCUIT CUT-OFF SYSTEM OPERATION.......................... 7-9
TROUBLESHOOTING ............................................................................ 7-11
CHARGING SYSTEM ................................................................................... 7-13
CIRCUIT DIAGRAM ................................................................................ 7-13
LIGHTING SYSTEM...................................................................................... 7-17
CIRCUIT DIAGRAM ................................................................................ 7-17
SIGNALING SYSTEM ................................................................................... 7-21
CIRCUIT DIAGRAM ................................................................................ 7-21
FUEL INJECTION SYSTEM ......................................................................... 7-27
CIRCUIT DIAGRAM ................................................................................ 7-27
ECU SELF-DIAGNOSTIC FUNCTION.................................................... 7-29
SELF-DIAGNOSTIC FUNCTION TABLE................................................ 7-30
TROUBLESHOOTING METHOD............................................................ 7-32
DIAGNOSTIC MODE .............................................................................. 7-33
TROUBLESHOOTING DETAILS ............................................................ 7-40
FUEL PUMP SYSTEM .................................................................................. 7-63
CIRCUIT DIAGRAM ................................................................................ 7-63
ELECTRICAL COMPONENTS ..................................................................... 7-67

CHECKING THE SWITCHES ................................................................. 7-71
CHECKING THE BULBS AND BULB SOCKETS ................................... 7-74
CHECKING THE FUSES ........................................................................ 7-75
CHECKING AND CHARGING THE BATTERY....................................... 7-76
CHECKING THE RELAYS ...................................................................... 7-79
CHECKING THE TURN SIGNAL RELAY ............................................... 7-80
CHECKING THE DIODES ...................................................................... 7-81
CHECKING THE IGNITION SPARK GAP .............................................. 7-82
CHECKING THE SPARK PLUG CAPS .................................................. 7-83
CHECKING THE IGNITION COILS ........................................................ 7-83
CHECKING THE CRANKSHAFT POSITION SENSOR ......................... 7-84
CHECKING THE LEAN ANGLE SENSOR ............................................. 7-84
CHECKING THE STARTER MOTOR OPERATION............................... 7-85
CHECKING THE STATOR COIL ............................................................ 7-85
CHECKING THE RECTIFIER/REGULATOR.......................................... 7-85
CHECKING THE HORNS ....................................................................... 7-86
CHECKING THE ENGINE TEMPERATURE SENSOR .......................... 7-87
CHECKING THE FUEL SENDER (FUEL TANK).................................... 7-87
CHECKING THE FUEL SENDER (FUEL PUMP) ................................... 7-88
CHECKING THE FUEL LEVEL WARNING LIGHT................................. 7-88
CHECKING THE SPEED SENSOR........................................................ 7-88
CHECKING THE THROTTLE POSITION SENSOR............................... 7-89
CHECKING THE FUEL PUMP................................................................ 7-89
CHECKING THE EXUP SERVO MOTOR .............................................. 7-90
CHECKING THE INTAKE AIR PRESSURE SENSOR ........................... 7-90
CHECKING THE AIR TEMPERATURE SENSOR.................................. 7-90
(GRAY)
WW W
7-1
Br
W
W
W
Br B
B R/L
Br
(GRAY)
L/Y L/B
R
Br/L
(BLACK)
Y Br
(BLACK)
L/B L/Y
(GRAY)
Br
Br
A B
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
(BLACK)
W/B L/W
(BLACK)
(BLACK)
L/W W/B
(BLACK)
B B
G/R G/B
Y Br
G/B G/R
R/W B/R
G/L L/B
R/Y
R/Y
Br
R/Y
R/W
R/W R/W R/W R/W
R R/Y
B/R R/W
L/B G/L
R/W
Br/L
Br
R/Y
Br/L
Br/L
R/G
R/B
L Y
B/R
R/Y
L
R/W
W/B
L/W
L/W
B/Y
L/B
L/B
(BLACK)
L Y B
Sb
Sb
Sb/W
PUSH
B L/B
G/B
G/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
L/B B
G/L
R/L
L/Y L/R
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B G
Br B
G
G/L
Y B
Ch Dg
Br/W
(GRAY)
Y/R
(GRAY)
(GRAY)
B B
G/Y G/B
Br
(BLACK)
(BLUE)
B/L
Y/B
Br
B
B
(BLACK)
L/Y B/Y
G/W
W L
B
Br
R/Y
R/Y
G/L
L W/Y
B/L
(BLACK)
B B
(BLACK)
(GRAY)
Br/W
Dg Ch
(GRAY)
P
Y/R
(GRAY)
B/Y L/Y
G/B G/Y
(BLACK)
(BLUE)
G
G/L
B/L
Gy
(BLUE)
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
B L/G
B
(BLUE)
B Gy
L/R R/Y
L/G
B/R
R/W
Ch
Y/B
G/L
Br B Br
Br/W
(L)
N
(R)
Dg
Br/W
Ch
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
Y/R
Br/W Y/R
B
Ch A Ch
Dg A Dg
Dg
G/L
B/L
L
W/Y
G/W B
R/L B
B
B
Gy/R
G
Gy Y/B Gy/R
O
O
W/Y Y/R
Br
Br/W
W/Y
PUSH
Ch L
G/B
G/Y
P
Br
(BLACK)
B/Br B
B/Br B
Br
L Ch
Ch L
B
B
(GRAY) (GRAY)
G
Gy
Y/B
Gy/G
Gy/W
Y/L
W/R
B/G
B/R
R/G
P/L
W/G
Br/L
O
O
Gy/R
Gy/R
Dg L
R/B
R/B
D D
R/B
R/B
R/B
R/B
B/W
W/G R/B R/G

Br/L R/B P/L
R/G
P/L
W/G
Br/L
L Dg
Dg L
B
B
(BLACK) (BLACK)
R/G D R/G
P/L D P/L
W/G D W/G
Br/L D Br/L
Gy/R C Gy/R
Gy/R C Gy/R
Gy/G L/B
Br/W P/Y W/R L
R/L R/W R/B B/Br P/L B/L R/G B/Y
L/W W/Y
Y/G Br
Gy R/B B/Br Y/L Y Br/L W/G
P/W L/R
Gy/W B/R
B/G
B G
G B G
Gy B Gy
B/G
B/R
Gy/R
B/R
Gy/R
B/R
B/R
B/L
Gy/W
(BLACK)
Gy/W R/L
Gy/G B/L
R/L
B B
W L
W Gy
(GRAY)
B
(DARK GRAY)
W B
W
W G
(BLACK)
L W/R B/L
B/G B/R
Gy/G
Gy
L
W/R
B/L
B/R
B/R
C
B/R
Dg
Ch
R/G
Y/L
G/W
G
R/W
G/R
G/Y
G/B
Dg
B
G
W
Br
B
Dg
B
L
Ch
Y
Br
B
G Gy
W W
(BLACK)
R/G R/B W/G

P/L R/B Br/L
L Y
B
G/Y G/R
G/B
G/R G/Y
G/B
(BLACK)
R/G G/W Y/L

B G
Y/L G/W R/G
G B
(BLACK)
Dg L Y
Ch Sb/W R/W
Sb/W
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS4
Y
L Dg
R/W Sb Ch
WIRE HARNESS
WIRE HARNESS
(BLACK)
W/G R/B R/G

Br/L R/B P/L
SUB-WIRE-HARNESS3
(BLACK)
WIRE HARNESS
Gy/R B/R Gy/R

(BLACK)
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS1
Gy/R B/R Gy/R
WIRE HARNESS
Gy
W
WIRE HARNESS
Ch
Y
IGNITION SYSTEM
EAS27090
IGNITION SYSTEM
EAS27110
CIRCUIT DIAGRAM
IGNITION SYSTEM
3. Main switch
4. Main fuse
6. Battery
11.Relay unit
14.Neutral switch
16.Sidestand switch
19.Crankshaft position sensor
23.Lean angle sensor
27.ECU (electronic control unit)
28.Cylinder-#1 left ignition coil
29.Cylinder-#1 right ignition coil
32.Spark plug
67.Engine stop switch
77.Ignition fuse
81.ECU fuse
7-2
IGNITION SYSTEM
ET1D71043
ENGINE STOPPING DUE TO SIDESTAND OPERATION

When the engine is running and the transmission is in gear, the engine will stop if the sidestand is
moved down. This is because the electric current from the ignition coils does not flow to the ECU when
both the neutral switch and sidestand switch are set to OFF, thereby preventing the spark plugs from
producing a spark. However, the engine continues to run under the following conditions:
The transmission is in gear (the neutral switch circuit is open) and the sidestand is up (the sidestand
switch circuit is closed).
The transmission is in neutral (the neutral switch circuit is closed) and the sidestand is down (the sidestand switch circuit is open).
2
1
4
5
10
8
6
11
9
7
1. Battery
2. Main fuse
3. Main switch
4. Ignition fuse
5. Engine stop switch
6. Ignition coil
7. Spark plug
9. Sidestand switch
10. Relay unit (diode)
11. Neutral switch
7-3
IGNITION SYSTEM
EAS27140
TROUBLESHOOTING
The ignition system fails to operate (no spark or intermittent spark).
NOTE:
Before troubleshooting, remove the following part(s):

1. Rider seat
2. Tool kit tray
3. Rider seat bracket assembly
4. Fuel tank
5. Air filter case
7. Exhaust pipes
8. Front cylinder
1. Check the fuses.
(Main, ignition and ECU)
Refer to CHECKING THE FUSES on page 7-75.
NG
Replace the fuse(s).
OK
2. Check the battery.
Refer to CHECKING AND
CHARGING THE BATTERY on
page 7-76.
NG
Clean the battery terminals.
Recharge or replace the battery.
OK
3. Check the spark plugs.
Refer to CHECKING THE SPARK
PLUGS on page 3-9.
NG
Re-gap or replace the spark plug(s).
OK
4. Check the ignition spark gap.
Refer to CHECKING THE IGNITION SPARK GAP on page 7-82.
OK
Ignition system is OK.
NG
5. Check the spark plug caps.
Refer to CHECKING THE SPARK
PLUG CAPS on page 7-83.
NG
Replace the spark plug cap(s).
OK
6. Check the ignition coils.
Refer to CHECKING THE IGNITION COILS on page 7-83.
NG
Replace the ignition coil(s).
OK
7. Check the crankshaft position sensor.
Refer to CHECKING THE CRANKSHAFT POSITION SENSOR on
page 7-84.
NG
Replace the crankshaft position sensor.
OK
7-4
IGNITION SYSTEM
8. Check the main switch.
Refer to CHECKING THE
SWITCHES on page 7-71.
NG
Replace the main switch.
OK
9. Check the engine stop switch.
NG
The engine stop switch is faulty. Replace

the right handlebar switch.
OK
10.Check the neutral switch.
NG
Replace the neutral switch.
OK
11.Check the sidestand switch.
NG
Replace the sidestand switch.
OK
12.Check the relay unit (diode).
Refer to CHECKING THE DIODES on page 7-81.
NG
Replace the relay unit.
OK
13.Check the lean angle sensor.
Refer to CHECKING THE LEAN
ANGLE SENSOR on page 7-84.
NG
Replace the lean angle sensor.
OK
14.Check the entire ignition system
wiring.
Refer to CIRCUIT DIAGRAM on
page 7-1.
NG
Properly connect or repair the ignition system wiring.
OK
Replace the ECU.
7-5
(GRAY)
WW W
7-7
Br
W
W
W
Br B
B R/L
Br
(GRAY)
L/Y L/B
R
Br/L
(BLACK)
Y Br
(BLACK)
L/B L/Y
(GRAY)
Br
Br
A B
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
(BLACK)
W/B L/W
(BLACK)
(BLACK)
L/W W/B
(BLACK)
B B
G/R G/B
Y Br
G/B G/R
R/W B/R
G/L L/B
R/Y
R/Y
Br
R/Y
R/W
R/W R/W R/W R/W
R R/Y
B/R R/W
L/B G/L
R/W
Br/L
Br
R/Y
Br/L
Br/L
R/G
R/B
L Y
B/R
R/Y
L
R/W
W/B
L/W
L/W
B/Y
L/B
L/B
(BLACK)
L Y B
Sb
Sb
Sb/W
PUSH
B L/B
G/B
G/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
L/B B
G/L
R/L
L/Y L/R
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B G
Br B
G
G/L
Ch Dg
Br/W
(GRAY)
P B
Y/R
(GRAY)
(GRAY)
B B
G/Y G/B
Y B
Br
(BLACK)
(BLUE)
B/L
Y/B
Br
B
B
(BLACK)
L/Y B/Y
G/W
W L
B
Br
R/Y
R/Y
G/L
L W/Y
B/L
(BLACK)
B B
(BLACK)
(GRAY)
Dg Ch
Br/W
(GRAY)
B P
Y/R
(GRAY)
B/Y L/Y
G/B G/Y
(BLACK)
(BLUE)
G
G/L
B/L
Gy
(BLUE)
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
B L/G
B
(BLUE)
B Gy
L/R R/Y
L/G
B/R
R/W
Ch
Y/B
G/L
Br B Br
Br/W
(L)
N
(R)
Dg
Br/W
Ch
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
Y/R
Br/W Y/R
B
Ch A Ch
Dg A Dg
Dg
G/L
B/L
L
W/Y
G/W B
R/L B
B
B
Gy/R
G
Gy Y/B Gy/R
O
O
W/Y Y/R
Br
Br/W
W/Y
PUSH
Ch L
G/B
G/Y
P
Br
(BLACK)
B/Br B
B/Br B
Br
L Ch
Ch L
B
B
(GRAY) (GRAY)
G
Gy
Y/B
Gy/G
Gy/W
Y/L
W/R
B/G
B/R
R/G
P/L
W/G
Br/L
O
O
Gy/R
Gy/R
Dg L
R/B
R/B
D D
R/B
R/B
R/B
R/B
B/W
W/G R/B R/G

Br/L R/B P/L
R/G
P/L
W/G
Br/L
L Dg
Dg L
B
B
(BLACK) (BLACK)
R/G D R/G
P/L D P/L
W/G D W/G
Br/L D Br/L
Gy/R C Gy/R
Gy/R C Gy/R
Gy/G L/B
Br/W P/Y W/R L
L/W W/Y
Y/G Br
P/W L/R
Gy/W B/R
B/G
B G
G B G
Gy B Gy
B/G
B/R
Gy/R
B/R
Gy/R
B/R
B/R
B/L
Gy/W
(BLACK)
Gy/W R/L
Gy/G B/L
R/L
B B
W L
W Gy
(GRAY)
B
(DARK GRAY)
W B
W
W G
(BLACK)
L W/R B/L
B/G B/R
Gy/G
Gy
L
W/R
B/L
B/R
B/R
C
B/R
Dg
Ch
R/G
Y/L
G/W
G
R/W
G/R
G/Y
G/B
Dg
B
G
W
Br
B
Dg
B
L
Ch
Y
Br
B
G Gy
W W
(BLACK)
R/G R/B W/G

P/L R/B Br/L
L Y
B
G/Y G/R
G/B
G/R G/Y
G/B
(BLACK)
R/G G/W Y/L

B G
Y/L G/W R/G
G B
(BLACK)
Dg L Y
Ch Sb/W R/W
Sb/W
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS4
Y
L Dg
R/W Sb Ch
WIRE HARNESS
WIRE HARNESS
(BLACK)
W/G R/B R/G

Br/L R/B P/L
SUB-WIRE-HARNESS3
(BLACK)
WIRE HARNESS
Gy/R B/R Gy/R

(BLACK)
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS1
Gy/R B/R Gy/R
WIRE HARNESS
Gy
W
WIRE HARNESS
Ch
Y
ELECTRIC STARTING SYSTEM
EAS27160
EAS27170
CIRCUIT DIAGRAM

3. Main switch
4. Main fuse
6. Battery
8. Starter relay
9. Starter motor
10.Diode 1
11.Relay unit
12.Starting circuit cut-off relay
14.Neutral switch
15.Diode 2
16.Sidestand switch
53.Clutch switch
68.Start switch
77.Ignition fuse
81.ECU fuse
7-8

EAS27180
STARTING CIRCUIT CUT-OFF SYSTEM OPERATION

If the engine stop switch is set to and the main switch is turned ON (both switch circuits are
closed), the starter motor can only operate if at least one of the following conditions is met:
The transmission is in neutral (the neutral switch circuit is closed).
The clutch lever is pulled to the handlebar (the clutch switch circuit is closed) and the sidestand is up
(the sidestand switch circuit is closed).
The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay stays open so current cannot reach
the starter motor. When at least one of the above conditions has been met, the starting circuit cut-off
relay is closed and the engine can be started by pushing the start switch .
14
13
1
2
17
3
4
15
5
6
7
8
8
9
8
b
10
16
7-9
a
11
12

a. WHEN THE TRANSMISSION IS IN
NEUTRAL
b. WHEN THE SIDESTAND IS UP AND THE
CLUTCH LEVER IS PULLED TO THE
HANDLEBAR
1. Battery
2. Main fuse
3. Main switch
4. Ignition fuse
6. Diode 2
7. Relay unit (starting circuit cut-off relay)
8. Relay unit (diode)
9. Clutch switch
11. Neutral switch
12. Start switch
13. Starter relay
14. Starter motor
15. ECU fuse
17. Diode 1
7-10

EAS27190
TROUBLESHOOTING
The starter motor fails to turn.
NOTE:

1. Rider seat
2. Tool kit tray
1. Check the fuses.
(Main, ignition and ECU)
NG
OK
page 7-76.
NG
OK
3. Check the starter motor operation.
Refer to CHECKING THE STARTER MOTOR OPERATION on page
7-85.
OK
Starter motor is OK. Perform the electric

starting system troubleshooting, starting
with step 5.
NG
4. Check the starter motor.
Refer to CHECKING THE STARTER MOTOR on page 5-79.
NG
Repair or replace the starter motor.
OK
5. Check the relay unit (starting circuit
cut-off relay).
Refer to CHECKING THE RELAYS on page 7-79.
NG
OK
6. Check the relay unit (diode).
NG
OK
7. Check the diode 1.
NG
Replace the diode 1.
OK
NG
OK
7-11

9. Check the starter relay.
NG
Replace the starter relay.
OK
10.Check the main switch.
NG
OK
11.Check the engine stop switch.
NG

OK
12.Check the neutral switch.
NG
OK
13.Check the sidestand switch.
NG
Replace the sidestand switch.
OK
14.Check the clutch switch.
NG
Replace the clutch switch.
OK
15.Check the start switch.
NG
The start switch is faulty. Replace the right

handlebar switch.
OK
16.Check the entire starting system
wiring.
page 7-7.
NG
Properly connect or repair the starting system wiring.
OK
The starting system circuit is OK.
7-12
(GRAY)
WW W
W
W
W
7-13
Br
(GRAY)
L/Y L/B
R
Br/L
L/B L/Y
(GRAY)
Br
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
R
R
R/Y
R/W
Br
Br/L
Br/L
Br/L
R/B
R/G
R/Y
R/Y
R/Y
R/W R/W R/W R/W
R R/Y
R/Y
L
R/W
L/W
B/Y
R/L
L/Y L/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
(BLACK)
L Y B
Sb
Sb
Sb/W
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B L/G
B/L
Gy
B/L
Br
(BLACK)
Br B
(BLACK)
B B
G/W
W L
B
Y/B
Br
R/Y
R/Y
G/L
L W/Y
B/L
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
(BLUE)
B Gy
B B
(BLUE)
L/R R/Y
L/G
B/R
R/W
Br
Y/B
G/L
Br B Br
Br/W
B/L
L
W/Y
G/W B
R/L B
Br/W Y/R
B
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
B
B
Br
B
Br/W
W/Y Y/R
W/Y
Br/W P/Y W/R

Y/G Br
Gy/W B/R
B/G
CHARGING SYSTEM
EAS27200
CHARGING SYSTEM
EAS27210
CIRCUIT DIAGRAM
CHARGING SYSTEM
1.
2.
4.
6.
AC magneto
Rectifier/regulator
Main fuse
Battery
7-14
CHARGING SYSTEM
EAS27220
TROUBLESHOOTING
The battery is not being charged.
NOTE:

1. Rider seat
2. Rectifier/regulator cover
3. Lead cover
1. Check the fuse.
(Main)
NG
Replace the fuse.
OK
page 7-76.
NG
OK
3. Check the stator coil.
Refer to CHECKING THE STATOR
COIL on page 7-85.
NG
Replace the stator coil.
OK
4. Check the rectifier/regulator.
Refer to CHECKING THE RECTIFIER/REGULATOR on page 7-85.
NG
Replace the rectifier/regulator.
OK
5. Check the entire charging system
wiring.
page 7-13.
NG
Properly connect or repair the charging
system wiring.
OK
The charging system circuit is OK.
7-15
(GRAY)
WW W
7-17
Br
W
W
W
Br B
B R/L
Br
(GRAY)
L/Y L/B
R
Br/L
(BLACK)
Y Br
(BLACK)
L/B L/Y
(GRAY)
Br
Br
A B
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
(BLACK)
W/B L/W
(BLACK)
(BLACK)
L/W W/B
(BLACK)
B B
G/R G/B
Y Br
G/B G/R
R/W B/R
G/L L/B
R/Y
R/Y
Br
R/Y
R/W
R/W R/W R/W R/W
R R/Y
B/R R/W
L/B G/L
R/W
Br/L
Br
R/Y
Br/L
Br/L
R/G
R/B
L Y
B/R
R/Y
L
R/W
W/B
L/W
L/W
B/Y
L/B
L/B
(BLACK)
L Y B
Sb
Sb
Sb/W
PUSH
B L/B
G/B
G/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
L/B B
G/L
R/L
L/Y L/R
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B G
Br B
G
G/L
(GRAY)
Ch Dg
Br/W
P B
Y/R
(GRAY)
(GRAY)
B B
G/Y G/B
Y B
Br
(BLACK)
(BLUE)
B/L
Y/B
Br
B
B
(BLACK)
L/Y B/Y
G/W
W L
B
Br
R/Y
R/Y
G/L
L W/Y
B/L
(BLACK)
B B
(BLACK)
(GRAY)
Dg Ch
Br/W
(GRAY)
B P
Y/R
(GRAY)
B/Y L/Y
G/B G/Y
(BLACK)
(BLUE)
G
G/L
B/L
Gy
(BLUE)
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
B L/G
B
(BLUE)
B Gy
L/R R/Y
L/G
B/R
R/W
Ch
Y/B
G/L
Br B Br
Br/W
(L)
N
(R)
Dg
Br/W
Ch
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
Y/R
Br/W Y/R
B
Ch A Ch
Dg A Dg
Dg
G/L
B/L
L
W/Y
G/W B
R/L B
B
B
Gy/R
G
Gy Y/B Gy/R
O
O
W/Y Y/R
Br
Br/W
W/Y
PUSH
Ch L
G/B
G/Y
P
Br
(BLACK)
B/Br B
B/Br B
Br
L Ch
Ch L
B
B
(GRAY) (GRAY)
G
Gy
Y/B
Gy/G
Gy/W
Y/L
W/R
B/G
B/R
R/G
P/L
W/G
Br/L
O
O
Gy/R
Gy/R
Dg L
R/B
R/B
D D
R/B
R/B
R/B
R/B
B/W
W/G R/B R/G

Br/L R/B P/L
R/G
P/L
W/G
Br/L
L Dg
Dg L
B
B
(BLACK) (BLACK)
R/G D R/G
P/L D P/L
W/G D W/G
Br/L D Br/L
Gy/R C Gy/R
Gy/R C Gy/R
Gy/G L/B
Br/W P/Y W/R L
L/W W/Y
Y/G Br
P/W L/R
Gy/W B/R
B/G
B G
G B G
Gy B Gy
B/G
B/R
Gy/R
B/R
Gy/R
B/R
B/R
B/L
Gy/W
(BLACK)
Gy/W R/L
Gy/G B/L
R/L
B B
W L
W Gy
(GRAY)
B
(DARK GRAY)
W B
W
W G
(BLACK)
L W/R B/L
B/G B/R
Gy/G
Gy
L
W/R
B/L
B/R
B/R
C
B/R
Dg
Ch
R/G
Y/L
G/W
G
R/W
G/R
G/Y
G/B
Dg
B
G
W
Br
B
Dg
B
L
Ch
Y
Br
B
G Gy
W W
(BLACK)
R/G R/B W/G

P/L R/B Br/L
L Y
B
G/Y G/R
G/B
G/R G/Y
G/B
(BLACK)
R/G G/W Y/L

B G
Y/L G/W R/G
G B
(BLACK)
Dg L Y
Ch Sb/W R/W
Sb/W
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS4
Y
L Dg
R/W Sb Ch
WIRE HARNESS
WIRE HARNESS
(BLACK)
W/G R/B R/G

Br/L R/B P/L
SUB-WIRE-HARNESS3
(BLACK)
WIRE HARNESS
Gy/R B/R Gy/R

(BLACK)
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS1
Gy/R B/R Gy/R
WIRE HARNESS
Gy
W
WIRE HARNESS
Ch
Y
LIGHTING SYSTEM
EAS27240
LIGHTING SYSTEM
EAS27250
CIRCUIT DIAGRAM
LIGHTING SYSTEM
3. Main switch
4. Main fuse
6. Battery
43.Meter light
46.High beam indicator light
51.Headlight relay
54.Dimmer switch
58.Front right turn signal/position light
59.Front left turn signal/position light
63.Headlight (high beam)
64.Headlight (low beam)
69.Accessory light switch
71.Accessory light (OPTION)
72.Tail/brake light
73.License plate light
78.Headlight fuse
79.Signaling system fuse
80.Taillight fuse
81.ECU fuse
7-18
LIGHTING SYSTEM
EAS27260
TROUBLESHOOTING
Any of the following fail to light: headlight (high beam), headlight (low beam), high beam indicator light,
taillight, license light, position light, meter light or accessory light (OPTION).
NOTE:

1. Rider seat
2. Tool kit tray
1. Check the condition of each bulb
and bulb socket.
Refer to CHECKING THE BULBS
AND BULB SOCKETS on page
7-74.
NG
Replace the bulb(s) and bulb socket(s).
OK
2. Check the fuses.
(Main, headlight, signaling system,
taillight and ECU)
NG
OK
page 7-76.
NG
OK
NG
OK
5. Check the dimmer switch.
NG
The dimmer switch is faulty. Replace the

left handlebar switch.
OK
6. Check the accessory light switch.
NG
The accessory light switch is faulty. Replace the right handlebar switch.
OK
7. Check the headlight relay.
NG
Replace the headlight relay.
OK
7-19
LIGHTING SYSTEM
8. Check the entire lighting system
wiring.
page 7-17.
NG
Properly connect or repair the lighting system wiring.
OK
The lighting system circuit is OK.
7-20
(GRAY)
WW W
7-21
Br
W
W
W
Br B
B R/L
Br
(GRAY)
L/Y L/B
R
Br/L
(BLACK)
Y Br
(BLACK)
L/B L/Y
(GRAY)
Br
Br
A B
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
(BLACK)
W/B L/W
(BLACK)
(BLACK)
L/W W/B
(BLACK)
B B
G/R G/B
Y Br
G/B G/R
R/W B/R
G/L L/B
R/Y
R/Y
Br
R/Y
R/W
R/W R/W R/W R/W
R R/Y
B/R R/W
L/B G/L
R/W
Br/L
Br
R/Y
Br/L
Br/L
R/G
R/B
L Y
B/R
R/Y
L
R/W
W/B
L/W
L/W
B/Y
L/B
L/B
(BLACK)
L Y B
Sb
Sb
Sb/W
PUSH
B L/B
G/B
G/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
L/B B
G/L
R/L
L/Y L/R
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B G
Br B
G
G/L
Ch Dg
Br/W
(GRAY)
P B
Y/R
(GRAY)
(GRAY)
B B
G/Y G/B
Y B
Br
(BLACK)
(BLUE)
B/L
Y/B
Br
B
B
(BLACK)
L/Y B/Y
G/W
W L
B
Br
R/Y
R/Y
G/L
L W/Y
B/L
(BLACK)
B B
(BLACK)
(GRAY)
Dg Ch
Br/W
(GRAY)
B P
Y/R
(GRAY)
B/Y L/Y
G/B G/Y
(BLACK)
(BLUE)
G
G/L
B/L
Gy
(BLUE)
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
B L/G
B
(BLUE)
B Gy
L/R R/Y
L/G
B/R
R/W
Ch
Y/B
G/L
Br B Br
Br/W
(L)
N
(R)
Dg
Br/W
Ch
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
Y/R
B/rW Y/R
B
Ch A Ch
Dg A Dg
Dg
G/L
B/L
L
W/Y
G/W B
R/L B
B
B
Gy/R
G
Gy Y/B Gy/R
O
O
W/Y Y/R
Br
Br/W
W/Y
PUSH
Ch L
G/B
G/Y
P
Br
(BLACK)
B/Br B
B/Br B
Br
L Ch
Ch L
B
B
(GRAY) (GRAY)
G
Gy
Y/B
Gy/G
Gy/W
Y/L
W/R
B/G
B/R
R/G
P/L
W/G
Br/L
O
O
Gy/R
Gy/R
Dg L
R/B
R/B
D D
R/B
R/B
R/B
R/B
B/W
W/G R/B R/G

Br/L R/B P/L
R/G
P/L
W/G
Br/L
L Dg
Dg L
B
B
(BLACK) (BLACK)
R/G D R/G
P/L D P/L
W/G D W/G
Br/L D Br/L
Gy/R C Gy/R
Gy/R C Gy/R
Gy/G L/B
Br/W P/Y W/R L
L/W W/Y
Y/G Br
P/W L/R
Gy/W B/R
B/G
B G
G B G
Gy B Gy
B/G
B/R
Gy/R
B/R
Gy/R
B/R
B/R
B/L
Gy/W
(BLACK)
Gy/W R/L
Gy/G B/L
R/L
B B
W L
W Gy
(GRAY)
B
(DARK GRAY)
W B
W
W G
(BLACK)
L W/R B/L
B/G B/R
Gy/G
Gy
L
W/R
B/L
B/R
B/R
C
B/R
Dg
Ch
R/G
Y/L
G/W
G
R/W
G/R
G/Y
G/B
Dg
B
G
W
Br
B
Dg
B
L
Ch
Y
Br
B
G Gy
W W
(BLACK)
R/G R/B W/G

P/L R/B Br/L
L Y
B
G/Y G/R
G/B
G/R G/Y
G/B
(BLACK)
R/G G/W Y/L

B G
Y/L G/W R/G
G B
(BLACK)
Dg L Y
Ch Sb/W R/W
Sb/W
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS4
Y L Dg
R/W Sb Ch
WIRE HARNESS
WIRE HARNESS
(BLACK)
W/G R/B R/G

Br/L R/B P/L
SUB-WIRE-HARNESS3
(BLACK)
WIRE HARNESS
Gy/R B/R Gy/R

(BLACK)
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS1
Gy/R B/R Gy/R
WIRE HARNESS
Gy
W
WIRE HARNESS
Ch
Y
SIGNALING SYSTEM
EAS27270
SIGNALING SYSTEM
EAS27280
CIRCUIT DIAGRAM
SIGNALING SYSTEM
3. Main switch
4. Main fuse
5. Backup fuse (odometer and clock)
6. Battery
11.Relay unit
14.Neutral switch
18.Fuel sender (fuel pump)
24.Speed sensor
39.Neutral indicator light
40.Multi-function meter
42.Fuel level warning light
44.Left turn signal indicator light
45.Right turn signal indicator light
47.Fuel sender (fuel tank)
48.Horn 1
49.Horn 2
50.Turn signal relay
55.Turn signal switch
56.Horn switch
58.Front right turn signal/position light
59.Front left turn signal/position light
60.Rear right turn signal light
61.Rear left turn signal light
66.Front brake light switch
72.Tail/brake light
74.Rear brake light switch
77.Ignition fuse
81.ECU fuse
7-22
SIGNALING SYSTEM
EAS27290
TROUBLESHOOTING
Any of the following fail to light: turn signal light, brake light or an indicator light.
The horn fails to sound.
The fuel level gauge fails to operate.
The speedometer fails to operate.
NOTE:

1. Rider seat
2. Tool kit tray
5. Fuel tank
1. Check the fuses.
(Main, backup, ignition, signaling
system and ECU)
NG
OK
page 7-76.
NG
OK
NG
OK
4. Check the entire signaling system
wiring.
page 7-21.
NG
Properly connect or repair the signaling
system wiring.
OK
Check the condition of each of the signaling systems circuits. Refer to
Checking the signaling system.
Checking the signaling system
The horn fails to sound.
1. Check the horn switch.
NG
OK
7-23
The horn switch is faulty. Replace the left

handlebar switch.
SIGNALING SYSTEM
2. Check the horns.
HORNS on page 7-86.
NG
Replace the horn(s).
OK
wiring.
page 7-21.
NG
system wiring.
OK
This circuit is OK.
The tail/brake light fails to come on.
1. Check the front brake light switch.
NG
Replace the front brake light switch.
OK
2. Check the rear brake light switch.
NG
Replace the rear brake light switch.
OK
wiring.
page 7-21.
NG
system wiring.
OK
This circuit is OK.
The turn signal light, turn signal indicator light or both fail to blink.
1. Check the condition of each bulb
and bulb socket.
Refer to CHECKING THE BULBS
AND BULB SOCKETS on page
7-74.
NG
Replace the bulb(s) and bulb socket(s).
OK
2. Check the turn signal switch.
NG
The turn signal switch is faulty. Replace

the left handlebar switch.
OK
3. Check the turn signal relay.
Refer to CHECKING THE TURN
SIGNAL RELAY on page 7-80.
NG
Replace the turn signal relay.
OK
7-24
SIGNALING SYSTEM
wiring.
page 7-21.
NG
system wiring.
OK
This circuit is OK.
The neutral indicator light fails to come on.
1. Check the neutral switch.
NG
OK
2. Check the relay unit (diode).
NG
OK
wiring.
page 7-21.
NG
system wiring.
OK
This circuit is OK.
The fuel level gauge fails to operate.
1. Check the fuel sender (fuel tank).
Refer to CHECKING THE FUEL
SENDER (FUEL TANK) on page
7-87.
NG
Replace the fuel sender.
OK
wiring.
page 7-21.
NG
system wiring.
OK
Replace the meter assembly.
The fuel level warning light fails to come on.
1. Check the fuel level warning light.
LEVEL WARNING LIGHT on page
7-88.
NG
Replace the meter assembly or fuel pump
assembly.
OK
7-25
SIGNALING SYSTEM
2. Check the fuel sender (fuel pump).
SENDER (FUEL PUMP) on page
7-88.
NG
Replace the fuel pump assembly.
OK
wiring.
page 7-21.
NG
system wiring.
OK
This circuit is OK.
The speedometer fails to operate.
1. Check the speed sensor.
Refer to CHECKING THE SPEED
SENSOR on page 7-88.
NG
Replace the speed sensor.
OK
wiring.
page 7-21.
NG
system wiring.
OK
7-26
(GRAY)
WW W
7-27
Br
W
W
W
Br B
B R/L
Br
(GRAY)
L/Y L/B
R
Br/L
(BLACK)
Y Br
(BLACK)
L/B L/Y
(GRAY)
Br
Br
A B
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
(BLACK)
W/B L/W
(BLACK)
(BLACK)
L/W W/B
(BLACK)
B B
G/R G/B
Y Br
G/B G/R
R/W B/R
G/L L/B
R/Y
R/Y
Br
R/Y
R/W
R/W R/W R/W R/W
R R/Y
B/R R/W
L/B G/L
R/W
Br/L
Br
R/Y
Br/L
Br/L
R/G
R/B
L Y
B/R
R/Y
L
R/W
W/B
L/W
L/W
B/Y
L/B
L/B
(BLACK)
L Y B
Sb
Sb
Sb/W
PUSH
B L/B
G/B
G/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
L/B B
G/L
R/L
L/Y L/R
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B G
Br B
G
G/L
Ch Dg
Br/W
(GRAY)
P B
Y/R
(GRAY)
(GRAY)
B B
G/Y G/B
Y B
Br
(BLACK)
(BLUE)
B/L
Y/B
Br
B
B
(BLACK)
L/Y B/Y
G/W
W L
B
Br
R/Y
R/Y
G/L
L W/Y
B/L
(BLACK)
B B
(BLACK)
(GRAY)
Dg Ch
Br/W
(GRAY)
B P
Y/R
(GRAY)
B/Y L/Y
G/B G/Y
(BLACK)
(BLUE)
G
G/L
B/L
Gy
(BLUE)
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
B L/G
B
(BLUE)
B Gy
L/R R/Y
L/G
B/R
R/W
Ch
Y/B
G/L
Br B Br
Br/W
(L)
N
(R)
Dg
Br/W
Ch
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
Y/R
Br/W Y/R
B
Ch A Ch
Dg A Dg
Dg
G/L
B/L
L
W/Y
G/W B
R/L B
B
B
Gy/R
G
Gy Y/B Gy/R
O
O
W/Y Y/R
Br
Br/W
W/Y
PUSH
Ch L
G/B
G/Y
P
Br
(BLACK)
B/Br B
B/Br B
Br
L Ch
Ch L
B
B
(GRAY) (GRAY)
G
Gy
Y/B
Gy/G
Gy/W
Y/L
W/R
B/G
B/R
R/G
P/L
W/G
Br/L
O
O
Gy/R
Gy/R
Dg L
R/B
R/B
D D
R/B
R/B
R/B
R/B
B/W
W/G R/B R/G

Br/L R/B P/L
R/G
P/L
W/G
Br/L
L Dg
Dg L
B
B
(BLACK) (BLACK)
R/G D R/G
P/L D P/L
W/G D W/G
Br/L D Br/L
Gy/R C Gy/R
Gy/R C Gy/R
Gy/G L/B
Br/W P/Y W/R L
L/W W/Y
Y/G Br
P/W L/R
Gy/W B/R
B/G
B G
G B G
Gy B Gy
B/G
B/R
Gy/R
B/R
Gy/R
B/R
B/R
B/L
Gy/W
(BLACK)
Gy/W R/L
Gy/G B/L
R/L
B B
W L
W Gy
(GRAY)
B
(DARK GRAY)
W B
W
W G
(BLACK)
L W/R B/L
B/G B/R
Gy/G
Gy
L
W/R
B/L
B/R
B/R
C
B/R
Dg
Ch
R/G
Y/L
G/W
G
R/W
G/R
G/Y
G/B
Dg
B
G
W
Br
B
Dg
B
L
Ch
Y
Br
B
G Gy
W W
(BLACK)
R/G R/B W/G

P/L R/B Br/L
L Y
B
G/Y G/R
G/B
G/R G/Y
G/B
(BLACK)
R/G G/W Y/L

B G
Y/L G/W R/G
G B
(BLACK)
Dg L Y
Ch Sb/W R/W
Sb/W
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS4
Y
L Dg
R/W Sb Ch
WIRE HARNESS
WIRE HARNESS
(BLACK)
W/G R/B R/G

Br/L R/B P/L
SUB-WIRE-HARNESS3
(BLACK)
WIRE HARNESS
Gy/R B/R Gy/R

(BLACK)
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS1
Gy/R B/R Gy/R
WIRE HARNESS
Gy
W
WIRE HARNESS
Ch
Y
FUEL INJECTION SYSTEM
EAS27330
EAS27340
CIRCUIT DIAGRAM

3. Main switch
4. Main fuse
6. Battery
7. Fuel injection system fuse
11.Relay unit
12.Starting circuit cut-off relay
13.Fuel pump relay
14.Neutral switch
15.Diode 2
16.Sidestand switch
17.Fuel pump
19.Crankshaft position sensor
20.Throttle position sensor
21.Cylinder-#1 intake air pressure sensor
22.Cylinder-#2 intake air pressure sensor
23.Lean angle sensor
24.Speed sensor
25.Air temperature sensor
26.Engine temperature sensor
32.Spark plug
33.ISC (idle speed control) unit
34.EXUP servo motor
35.Injector #1
36.Injector #2
37.O2 sensor
40.Multi-function meter
41.Engine trouble warning light
51.Headlight relay
54.Dimmer switch
57.Select switch
63.Headlight (high beam)
64.Headlight (low beam)
70.Reset switch
77.Ignition fuse
78.Headlight fuse
81.ECU fuse
7-28

EAS27350
ECU SELF-DIAGNOSTIC FUNCTION

The ECU is equipped with a self-diagnostic function in order to ensure that the fuel injection system is
operating normally. If this function detects a malfunction in the system, it immediately operates the engine under substitute characteristics and illuminates the engine trouble warning light to alert the rider
that a malfunction has occurred in the system. Once a malfunction has been detected, a fault code is
stored in the memory of the ECU.
To inform the rider that the fuel injection system is not functioning, the engine trouble warning light
flashes when the start switch is being pushed to start the engine.
If a malfunction is detected in the system by the self-diagnostic function, the ECU provides an appropriate substitute characteristic operation, and alerts the rider of the detected malfunction by illuminating the engine trouble warning light.
After the engine has been stopped, the lowest fault code number appears on the odometer/tripmeter/fuel reserve tripmeter/clock LCD. Once a fault code has been displayed, it remains stored in the
memory of the ECU until it is deleted.
Engine trouble warning light indication and fuel injection system operation
Warning light indication
Flashing*
Remains on
ECU operation
Fuel injection operation
Vehicle operation
Warning provided
when unable to start
engine
Operation stopped
Cannot be operated
Malfunction detected
Operated with substitute characteristics in

accordance with the
description of the malfunction
Can or cannot be operated depending on the

fault code
* The warning light flashes when any one of the conditions listed below is present and the start switch
is pushed:
Lean angle sensor
12:
Crankshaft position sensor
41:
(open or short-circuit)
19:
Blue/black ECU lead

(broken or disconnected)
30:
Lean angle sensor

(latch up detected)
50:
ECU internal malfunction

(memory check error)
Checking the engine trouble warning light

The engine trouble warning light comes on for 1.4 seconds after the main switch has been turned to
ON and it comes on while the start switch is being pushed. If the warning light does not come on under
these conditions, the warning light (LED) may be defective.
b
c
a.
b.
c.
d.
Main switch OFF

Main switch ON
Engine trouble warning light off
Engine trouble warning light on for 1.4
seconds
7-29

EAS27380
SELF-DIAGNOSTIC FUNCTION TABLE

If the ECU detects an abnormal signal from a sensor while the vehicle is being driven, the ECU illuminates the engine trouble warning light and provides the engine with alternate operating instructions that
are appropriate for the type of malfunction.
When an abnormal signal is received from a sensor, the ECU processes the specified values that are
programmed for each sensor in order to provide the engine with alternate operating instructions that
enable the engine to continue to operate or stop operating, depending on the conditions.
Self-Diagnostic Function table
Fault
code No.
Item
Symptom
Able / unable to start
Able / unable to
drive
12
Crankshaft position
sensor
No normal signals are received

from the crankshaft position sensor.
Unable
Unable
13
Cylinder-#1 intake air

pressure sensor
(open or short circuit)
Cylinder-#1 intake air pressure

sensor: open or short circuit detected.
Able
Able
14

pressure sensor
(hose system)

sensor: hose system malfunction
(clogged or detached hose).
Able
Able
15

Throttle position sensor: open or

short circuit detected.
Able
Able
17
EXUP servo motor

circuit
EXUP servo motor circuit: open or

Able
Able
18
EXUP servo motor

(lock)
EXUP servo motor is stuck.
Able
Able
19
Blue/black ECU lead

(broken or disconnected)
A break or disconnection of the

blue/black lead of the ECU is detected.
Unable
Unable
22

Air temperature sensor: open or

Able
Able
24
O2 sensor
No normal signal is received from

the O2 sensor.
Able
Able
25

pressure sensor

sensor: open or short circuit detected.
Able
Able
26

pressure sensor
(hose system)

sensor: hose system malfunction
(clogged or detached hose).
Able
Able
28
Engine temperature
sensor
Engine temperature sensor: open

or short circuit detected.
Able
Able
30
Lean angle sensor

(latch up detected)
The vehicle has overturned.
Unable
Unable
7-30

Fault
code No.
Item
Symptom
Able / unable to
drive
Cylinder-#1 left or
right ignition coil
(faulty ignition)
Able
(depending
Malfunction detected in the primaon the
ry wire of the cylinder-#1 left or
number of
right ignition coil.
faulty cylinders)
Able
(depending
on the
number of
faulty cylinders)
Cylinder-#2 left or
right ignition coil
(faulty ignition)
Able
(depending
number of
faulty cylinders)
Able
(depending
on the
number of
faulty cylinders)
Cylinder-#1 left or
right ignition coil
(faulty ignition)
Able
(depending
number of
faulty cylinders)
Able
(depending
on the
number of
faulty cylinders)
36
Cylinder-#2 left or
right ignition coil
(faulty ignition)
Able
(depending
number of
faulty cylinders)
Able
(depending
on the
number of
faulty cylinders)
37
ISC valve (stuck fully

open)
Engine speed is high when the enAble

gine is idling.
Able
41
Lean angle sensor

Lean angle sensor: open or short

circuit detected.
Unable
Unable
Speed sensor
No normal signals are received

from the speed sensor.
Open or short circuit is detected in
the neutral switch.
Able
Able
Neutral switch
43
Fuel system voltage

(monitoring voltage)
The ECU is unable to monitor the

battery voltage
Able
(an open or short circuit in the line
to the ECU).
Able
44
Error in writing the

amount of CO adjustment on EEPROM
Error is detected while reading or

writing on EEPROM (CO adjustment value).
Able
Able
46
Vehicle system power

Power supply to the fuel injection
supply
system is not normal.
(Monitoring voltage)
Able
Able
50
Faulty ECU memory. (When this

ECU internal malfuncmalfunction is detected in the
tion
ECU, the fault code number might
(memory check error)
not appear on the meter.)
Unable
Unable
33
34
35
42
7-31

Fault
code No.
70
Item
Engine idling stop
Symptom
Engine has been left idling. (The
ECU automatically stops the engine after 20 minutes if it is left
idling.)
Able
Able / unable to
drive
Able
Communication error with the meter

Fault
code No.
Item
Symptom
Able / unable to
drive
Er-1
ECU internal malfuncNo signals are received from the

tion
ECU.
(output signal error)
Unable
Unable
Er-2
ECU internal malfuncNo signals are received from the

tion
ECU within the specified duration.
Unable
Unable
Er-3
ECU internal malfuncData from the ECU cannot be retion

ceived correctly.
Unable
Unable
Er-4
ECU internal malfuncNon-registered data has been retion

ceived from the meter.
(input signal error)
Unable
Unable
2. Check and repair the probable cause of malfunction.
EAS27400
TROUBLESHOOTING METHOD
Fault code No.
The engine operation is not normal and the

engine trouble warning light comes on.
1. Check:
Fault code number
Check and repair.

Refer to TROUBLESHOOTING DETAILS on page 7-40.
Monitor the operation of the sensors
and actuators in the
diagnostic mode. Refer to Sensor operation table and
Actuator operation
table.
a. Check the fault code number displayed on

the meter.
b. Identify the faulty system with the fault code.
Refer to Self-Diagnostic Function table.
c. Identify the probable cause of the malfunction. Refer to Diagnostic code table.
No fault code No.

Check and repair.
Refer to Self-Diagnostic Function table.
3. Perform ECU reinstatement action.

Refer to Reinstatement method of table in
TROUBLESHOOTING DETAILS.
4. Turn the main switch to OFF and back to
ON, then check that no fault code number is
displayed.
NOTE:
If fault codes are displayed, repeat steps (1) to

(4) until no fault code number is displayed.
7-32

5. Erase the malfunction history in the diagnostic mode. Refer to Sensor operation table
(Diagnostic code No. 62).
The engine operation is not normal but the

engine trouble warning light does not come
on.
1. Check the operation of following sensors and
actuators in the Diagnostic mode. Refer to
Sensor operation table and Actuator operation table.
01: Throttle position sensor (throttle angle)
30: Cylinder-#1 ignition coil
36: Injector #1
37: Injector #2
NOTE:
Turning the main switch to OFF will not erase

the malfunction history.
If a malfunction is detected in the sensors or

actuators, repair or replace all faulty parts.
If no malfunction is detected in the sensors
and actuators, check and repair inner parts of
the engine.
EAS27420
DIAGNOSTIC MODE
Setting the diagnostic mode
1. Turn the main switch to OFF and set the engine stop switch to .
2. Disconnect the wire harness coupler from the fuel pump.
3. Press and hold the RESET switch, turn the main switch to ON, and continue to press the switch
for 8 seconds or more.
SELECT
RESET
NOTE:
All displays on the meter disappear except the clock and odometer/trip meter/fuel reserve trip
meter/clock displays.
dIAG appears on the odometer/trip meter/fuel reserve trip meter/clock LCD.
4. Simultaneously press the SELECT and RESET switches for 2 seconds or more to activate the
diagnostic mode. The diagnostic code number d01 appears on the clock LCD.
5. Set the engine stop switch to .
6. Select the diagnostic code number corresponding to the fault code number by pressing the SELECT and RESET switches.
NOTE:
To decrease the selected diagnostic code number, press the RESET switch. Press the RESET
switch for 1 second or longer to automatically decrease the diagnostic code numbers.
To increase the selected diagnostic code number, press the SELECT switch. Press the SELECT
switch for 1 second or longer to automatically increase the diagnostic code numbers.
7-33
d01
d70
d70
d01
7. Verify the operation of the sensor or actuator.

Sensor operation
The data representing the operating conditions of the sensor appears on the odometer/trip meter/fuel reserve trip meter/clock LCD.
Actuator operation
Set the engine stop switch to to operate the actuator.
NOTE:
If the engine stop switch is set to
, set it to
, and then set it to
again.
8. Turn the main switch to OFF to cancel the diagnostic mode.

Diagnostic code table
Fault
code
No.
Symptom
Probable cause of malfunction
Diagnostic
code No.
12
No normal signals are received from the crankshaft

position sensor.
Open or short circuit in wire harness.

Defective crankshaft position sensor.
Malfunction in crankshaft position sensor
rotor.
Malfunction in ECU.
Improperly installed sensor.
13

Cylinder-#1 intake air pres Defective cylinder-#1 intake air pressure
sure sensor: open or short
sensor.
circuit detected.
Malfunction in ECU.
03
14
Cylinder-#1 intake air pres Cylinder-#1 intake air pressure sensor hose
sure sensor: hose system
is detached, clogged, kinked, or pinched.
03
malfunction (clogged or de Malfunction in ECU.
tached hose).
15
Open or short circuit in wire sub lead.

Throttle position sensor:
open or short circuit detect- Defective throttle position sensor.
01
ed.
Malfunction in ECU.
Improperly installed throttle position sensor.
17
EXUP servo motor circuit: Open or short circuit in wire harness.

open or short circuit detect- Defective EXUP servo motor (potentiomeed.
ter circuit).
53
18

EXUP servo motor is stuck. Stuck EXUP servo motor (mechanism).
Stuck EXUP servo motor (motor).
53
7-34

Fault
code
No.
Symptom
Diagnostic
code No.
19
A break or disconnection of
Open circuit in wire harness (ECU coupler).
the blue/black lead of the
20
Malfunction in ECU.
ECU is detected.
22

Air temperature sensor:
Defective air temperature sensor.
open or short circuit detect05
Malfunction in ECU.
ed.
Improperly installed air temperature sensor.
24
No normal signal is received from the O2 sensor.
25

Cylinder-#2 intake air pres- Open or short circuit in wire harness.
sure sensor: open or short Defective cylinder-#2 intake air pressure
circuit detected.
sensor.
Malfunction in ECU.
26
Cylinder-#2 intake air pres Cylinder-#2 intake air pressure sensor hose
sure sensor: hose system
is detached, clogged, kinked, or pinched.
04
malfunction (clogged or de Malfunction in ECU.
tached hose).
28
Engine temperature sensor: open or short circuit

detected.

Defective engine temperature sensor.
Malfunction in ECU.
11
30
Overturned.
Malfunction in ECU.
08
33

Malfunction detected in the Malfunction in cylinder-#1 left or right igniprimary wire of the cylintion coil.
der-#1 left or right ignition
Malfunction in ECU.
coil.
Malfunction in a component of ignition cutoff circuit system.
30
32
34

Malfunction detected in the
Malfunction in cylinder-#2 left or right igniprimary wire of the cylintion coil.
Malfunction in ECU.
coil.
31
33
35

Malfunction detected in the Malfunction in cylinder-#1 left or right igniprimary wire of the cylintion coil.
Malfunction in ECU.
coil.
30
32

Defective O2 sensor.
Malfunction in ECU.
7-35
04

Fault
code
No.
Symptom
Diagnostic
code No.
36

Malfunction detected in the
Malfunction in cylinder-#2 left or right igniprimary wire of the cylintion coil.
Malfunction in ECU.
coil.
37
Open circuit in wire harness.

Malfunction in throttle body.
Malfunction in throttle cables.
ISC valve is stuck fully open due to disconnected ISC unit hose or coupler. (High enEngine speed is high when
gine idle speed is detected with the ISC
54
the engine is idling.
valve stuck fully open even though signals
for the valve to close are continuously being
transmitted by the ECU.)
Malfunction in ECU.
ECU fuse is blown.
41

Lean angle sensor: open or
Defective lean angle sensor.
Malfunction in ECU.
42
Open circuit in wire harness.

Defective speed sensor.
No normal signals are re Malfunction in vehicle speed sensor detectceived from the speed sened.
07
sor.
Defective neutral switch.
21
Open circuit is detected in
Malfunction in the engine side of the neutral
the neutral switch.
switch.
Malfunction in ECU.
43
The ECU is unable to monitor the battery voltage (an Open or short circuit in wire harness.
open or short circuit in the Malfunction in ECU.
line to the ECU).
44
Error is detected while

Malfunction in ECU. (The CO adjustment
reading or writing on EEvalue is not properly written on or read from 60
PROM (CO adjustment valthe internal memory).
ue).
46
Power supply to the fuel inMalfunction in the charging system. Refer to

jection system is not norCHARGING SYSTEM on page 7-13.
mal.
50
Faulty ECU memory.

(When this malfunction is
detected in the ECU, the
fault code number might
not appear on the meter.)
Malfunction in ECU. (The program and data

are not properly written on or read from the
internal memory.)
No signals are received

from the ECU.

Malfunction in meter.
Malfunction in ECU.
Defective wire connection of the ECU coupler.
Er-1
7-36
31
33
08
09

Fault
code
No.
Symptom
Diagnostic
code No.
Er-2
No signals are received

from the ECU within the
specified duration.
Improper connection in wire harness.

Malfunction in ECU.
Er-3
Data from the ECU cannot

be received correctly.

Malfunction in ECU.
Er-4
Non-registered data has

been received from the
meter.

Malfunction in ECU.
Sensor operation table

Diagnostic
code
No.
01
Item
Meter display
Checking method
Throttle angle
Fully closed position
1222
Check with throttle fully

closed.
Fully opened position
87107
Check with throttle fully

open.
03
Pressure difference
Displays the cylinder-#1 in(atmospheric pressure and take air pressure.
cylinder-#1 intake air pressure)
Set the engine stop switch

to , and then push the
start switch . (If the display value changes, the
performance is OK.)
04
Pressure difference
Displays the cylinder-#2 in(atmospheric pressure and take air pressure.
cylinder-#2 intake air pressure)

to , and then push the
start switch . (If the display value changes, the
performance is OK.)
05
Air temperature
Displays the air temperature. Compare the actually measured air temperature with
the meter display value.
07
Vehicle speed pulse
0999
08
Lean angle sensor
Check that the number increases when the rear

wheel is rotated. The number is cumulative and does
not reset each time the
wheel is stopped.
Upright
0.41.4
Overturned
3.74.4
7-37
Remove the lean angle

sensor and incline it more
than 65 degrees.

Diagnostic
code
No.
Item
Meter display
Checking method
09
Fuel system voltage

(battery voltage)
Approximately 12.0
11
Engine temperature
Displays the engine tempera- Compare the actually meature.

sured engine temperature
with the meter display value.
20
Sidestand switch
21
Stand retracted
ON
Stand extended
OFF

to , and then compare
with the actually measured
battery voltage. (If the battery voltage is lower, perform recharging.)
Set on/off the sidestand

switch (with the transmission in gear).
Neutral switch
Shift the transmission.
Neutral
ON
In gear
OFF
53
EXUP servo motor
Displays the operating angle.

Engine trouble warning light
comes on twice: once when
the EXUP valve is closing
and once when it is opening.
60
EEPROM fault code display
61
62
No history
00
History exists
01 or 02 (Cylinder fault code)

(If both cylinders are defective, the display alternates
every two seconds.)
Malfunction history code

display
No history
00
History exists
Fault codes 12-70

(If more than one code
number is detected, the display alternates every two
seconds to show all the detected code numbers.
When all code numbers are
shown, the display repeats
the same process.)
Malfunction history code

erasure
No history
History exists
Up to 25 fault codes
To erase the history, set the

engine stop switch to .
7-38

Diagnostic
code
No.
70
Item
Control number
Meter display
0255
Checking method
Actuator operation table

Diagnostic
code
No.
30
31
32
33
36
37
50
Item
Actuation
Checking method
Cylinder-#1 left or right ignition coil
Actuates the cylinder-#1 left

or right ignition coil five times Check the spark five times.
at one-second intervals.
Connect an ignition
Illuminates the engine trouchecker.
ble warning light.

Connect an ignition
ble warning light.

Connect an ignition
ble warning light.

Connect an ignition
ble warning light.
Injector #1
Actuates the injector #1 five

times at one-second intervals.
Illuminates the engine trouble warning light.
Check the operating sound

of the injector #1 five times.
Injector #2
Actuates the injector #2 five

times at one-second intervals.
Check the operating sound

of the injector #2 five times.
Fuel pump relay
Actuates the fuel pump relay

five times at one-second intervals.
Illuminates the engine trouCheck the operating sound
ble warning light.
of the fuel pump relay five
(The engine trouble warning
times.
light is OFF when the relay is
ON, and the engine trouble
warning light is ON when the
relay is OFF).
7-39

Diagnostic
code
No.
52
54
Item
Actuation
Checking method
Headlight relay
Actuates the headlight relay

for five cycles of five seconds. (ON 2 seconds, OFF 3 Check the operating sound
seconds)
of the headlight relay five
Illuminates the engine troutimes.
ble warning light and headlight.
ISC valve
Actuates and fully closes the

ISC valve, then opens it to
the standby opening position
when the engine is started.
The ISC unit vibrates when
This operation takes approxithe ISC valve operates.
mately 12 seconds until it is
completed.
EAS27460
TROUBLESHOOTING DETAILS
This section describes the measures per fault code number displayed on the meter. Check and service
the items or components that are the probable cause of the malfunction following the order given.
After the check and service of the malfunctioning part has been completed, reset the meter display according to the reinstatement method.
Fault code No.:
Code number displayed on the meter when the engine failed to work normally. Refer to Self-Diagnostic
Function table.
Diagnostic code No.:
Diagnostic code number to be used when the diagnostic mode is operated. Refer to DIAGNOSTIC
MODE on page 7-33.
7-40

Fault code No.
12
Diagnostic code No.
Symptom No normal signals are received from the crankshaft position sensor.
Order Item/components and probable

cause
Check or maintenance job
Reinstatement
method
Installed condition of crankshaft position sensor.
Check for looseness or pinching.
Cranking the
engine.
Connections
Main wire harness ECU coupler
Check the coupler for any pins

that may be pulled out.
Check the locking condition of
the coupler.
If there is a malfunction, repair it
and connect the coupler securely.
Repair or replace if there is an

open or short circuit.
Between the crankshaft position
sensor coupler and ECU coupler.
(graygray)
(black/blueblack/blue)
Defective crankshaft position sensor.
Replace if defective.
CRANKSHAFT POSITION
SENSOR on page 7-84.
7-41

Fault code No.
13
Diagnostic code No.
Symptom Cylinder-#1 intake air pressure sensor: open or short circuit detected.
03

cause
Connections
Check the coupler for any pins Turning the

main switch to
ON.
the coupler.

Between cylinder-#1 intake air
pressure sensor coupler and
ECU coupler
(pink/whitepink/white)
(blueblue)
Defective cylinder-#1 intake air pressure sensor.
Execute the diagnostic mode.

(Code No.03)
Refer to CHECKING THE INTAKE AIR PRESSURE SENSOR on page 7-90.
7-42
Reinstatement
method

Fault code No.
14
Diagnostic code No.
Symptom Cylinder-#1 intake air pressure sensor: hose system malfunction (clogged or detached hose).
03

cause
Reinstatement
method
Cylinder-#1 intake air pressure sensor Check the cylinder-#1 intake air Starting the enhose
pressure sensor hose condition. gine and oper Repair or replace the sensor
ating it at idle.
hose.
Cylinder-#1 intake air pressure sensor Check and repair the connecmalfunction at intermediate electrical
tion.
potential.
Replace it if there is a malfunction.
Connections

the coupler.

(Code No.03)
7-43

Fault code No.
15
Diagnostic code No.
Symptom Throttle position sensor: open or short circuit detected.

01

cause
Installed condition of throttle position

sensor.
Check for looseness or pinchTurning the

ing.
main switch to
Check that the sensor is inON.
stalled in the specified position.
Connections
Throttle position sensor coupler

the coupler.
Open or short circuit in wire harness

and/or sub lead.

Between throttle position sensor coupler and ECU coupler
(blueblue)
(yellowyellow)
(blackblack)
Throttle position sensor lead wire

open circuit output voltage check.
Check for open circuit and replace the throttle position sensor.
(blackyellow)
Defective throttle position sensor.
Open circuit
item
Output voltage
Ground wire
open circuit
5V
Output wire
open circuit
0V
Power supply
wire open circuit
0V

(Code No.01)
THROTTLE POSITION SENSOR on page 7-89.
7-44
Reinstatement
method

Fault code No.
17
Diagnostic code No.
Symptom EXUP servo motor circuit: open or short circuit detected.

53
EXUP servo motor

cause
Connections
EXUP servo motor coupler

main switch to
ON.
the coupler.

Between servo motor coupler
and ECU coupler
(blueblue)
(white/redwhite/red)
Defective EXUP servo motor (potenti- Execute the diagnostic mode.

ometer circuit).
(Code No.53)
EXUP SERVO MOTOR on
page 7-90.
Fault code No.
18
Diagnostic code No.
Reinstatement
method
Symptom EXUP servo motor is stuck.

53
EXUP servo motor

cause
Reinstatement
method
Connections
EXUP servo motor coupler

the coupler.

Between the EXUP servo motor
coupler and the ECU coupler.
(black/greenblack/green)
(black/redblack/red)
Turning the
main switch to
ON.
It takes 120
seconds at the
maximum before the original state
returns.
Defective EXUP servo motor.

(Code No.53)
EXUP SERVO MOTOR on
page 7-90.
Defective EXUP valve, pulley, cables.
7-45

Fault code No.
19
Diagnostic code No.
Symptom A break or disconnection of the blue/black lead of the

ECU is detected.
20
Sidestand switch

cause
Reinstatement
method
Connections

(Code No.20)
the coupler.
If the transmission is in gear,

retracting the
sidestand.
If the transmission is in neutral,
reconnecting
the wiring.

Between ECU and blue/black
lead
Defective sidestand switch.
Fault code No.
22
Diagnostic code No.
Symptom Air temperature sensor: open or short circuit detected.

05

cause
Reinstatement
method
Installed condition of air temperature

sensor.
Connections

the coupler.
Turning the
main switch to
ON.

Between air temperature sensor coupler and ECU coupler
(brown/whitebrown/white)
Defective air temperature sensor.

(Code No.05)
Refer to CHECKING THE AIR
TEMPERATURE SENSOR on
page 7-90.
7-46

Fault code No.
24
Diagnostic code No.
Symptom No normal signal is received from the O2 sensor.

cause
Reinstatement
method
Starting the engine and operating it at idle.
Installed state of O2 sensor.
Connections
O2 sensor coupler

the coupler.

Between O2 sensor coupler and
ECU coupler.
(gray/whitegray/white)
(red/bluered/blue)
(gray/greengray/green)
Check fuel pressure.
Refer to THROTTLE BODIES

on page 6-6.
Defective O2 sensor.
7-47

Fault code No.
25
Diagnostic code No.
Symptom Cylinder-#2 intake air pressure sensor: open or short circuit detected.
04

cause
Connections

main switch to
ON.
the coupler.

and/or sub lead.

Between cylinder-#2 intake air
pressure sensor coupler and
ECU coupler
(pink/yellowpink/yellow)
(blueblue)

(Code No.04)
7-48
Reinstatement
method

Fault code No.
26
Diagnostic code No.
Symptom Cylinder-#2 intake air pressure sensor: hose system malfunction (clogged or detached hose).
04

cause
Reinstatement
method
Cylinder-#2 intake air pressure sensor Check the cylinder-#2 intake air Starting the enhose
pressure sensor hose condition. gine and oper Repair or replace the sensor
ating it at idle.
hose.
Cylinder-#2 intake air pressure sensor Check and repair the connecmalfunction at intermediate electrical
tion.
potential.
Replace it if there is a malfunction.
Connections

the coupler.

(Code No.04)
7-49

Fault code No.
28
Diagnostic code No.
Symptom Engine temperature sensor: open or short circuit detected.

11

cause
Reinstatement
method
Installed state of engine temperature

sensor.
Connections
Engine temperature sensor coupler

the coupler.
Turning the
main switch to
ON.

and/or sub lead.

Between engine temperature
sensor coupler and ECU coupler
(brownbrown)
(blackblack)
Defective engine temperature sensor. Execute the diagnostic mode.

(Code No.11)
Refer to CHECKING THE ENGINE TEMPERATURE SENSOR on page 7-87.
Fault code No.
30
Diagnostic code No.
Symptom The vehicle has overturned.

08
Lean angle sensor

cause
Reinstatement
method
Raise the vehicle upright.
Installed condition of the lean angle

sensor.
Connections
Lean angle sensor coupler

the coupler.
Turning the
main switch to
ON (however,
the engine cannot be restarted
unless the main
switch is first
turned OFF).

(Code No.08)
LEAN ANGLE SENSOR on
page 7-84.
7-50

Fault code No.
33
Diagnostic code No.
Symptom Malfunction detected in the primary wire of the cylinder-#1

left or right ignition coil.
30, 32

cause
Connections
connector (primary coil side)
Check the connector and couStarting the enpler for any pins that may be
gine and operpulled out.
ating it at idle.
the connector and coupler.

Between cylinder-#1 left or right
ignition coil connector and ECU
coupler/main wire harness.
(black/redblue/red)
(orangeorange)
Defective cylinder-#1 left or right ignition coil.

(Code No.30 or 32)
Test the primary and secondary
coils for continuity.
7-51
Reinstatement
method

Fault code No.
34
Diagnostic code No.

31, 33

cause
Connections
ating it at idle.

and/or sub lead.

(black/redblue/red)
(gray/redgray/red)

(Code No.31 or 33)
7-52
Reinstatement
method

Fault code No.
35
Diagnostic code No.

30, 32

cause
Connections
ating it at idle.

(black/redblue/red)
(orangeorange)

(Code No.30 or 32)
7-53
Reinstatement
method

Fault code No.
36
Diagnostic code No.

31, 33

cause
Connections
ating it at idle.

and/or sub lead.

(black/redblue/red)
(gray/redgray/red)

(Code No.31 or 33)
7-54
Reinstatement
method

Fault code No.
37
Diagnostic code No.
Symptom Engine speed is high when the engine is idling.

54
ISC valve

cause
Reinstatement
method
ECU fuse is blown.
Check the ECU fuse.

FUSES on page 7-75.
Throttle valve does not fully close.
Check the throttle bodies.

Refer to THROTTLE BODIES
on page 6-6.
Check the throttle cables.
Refer to ADJUSTING THE
THROTTLE CABLE FREE
PLAY on page 3-8.
ISC valve is stuck fully open due to

Check that the ISC unit hose is
disconnected ISC unit hose or counot disconnected.
pler. (High engine idle speed is de Check that the ISC unit coupler
tected with the ISC valve stuck fully
is not disconnected.
open even though signals for the valve The ISC valve is stuck fully
to close are continuously being transopen if it does not operate when
mitted by the ECU.)
the main switch is turned OFF.
(Touch the ISC unit with your
hand and check if it is vibrating
to confirm if the ISC valve is operating.)
ISC valve returns to its original position by

turning the
main switch to
ON and back
to OFF.
Reinstated if
the engine idle
speed is within
specification after starting the
engine.
ISC valve is not moving correctly.

(Code No.54)
After the ISC valve is fully
closed, it opens to the standby
opening position when the engine is started. This operation
takes approximately 12 seconds. Start the engine. If the error recurs, replace the throttle
body assembly.
7-55

Fault code No.
41
Diagnostic code No.
Symptom Lean angle sensor: open or short circuit detected.

08
Lean angle sensor

cause
Connections
Lean angle sensor coupler

main switch to
ON.
the coupler.
Open or short circuit in lead wire.

Between lean angle sensor
coupler and ECU coupler.
(blueblue)
(yellow/greenyellow/green)

(Code No.08)
LEAN ANGLE SENSOR on
page 7-84.
7-56
Reinstatement
method

Fault code No.
42
Diagnostic code No.
Symptom A. No normal signals are received from the speed sensor.

B. Open circuit is detected in the neutral switch.
A
07
Speed sensor
21
Neutral switch

cause
Reinstatement
method
A-1
Connections
Speed sensor coupler

the coupler.
A-2
Open or short circuit in speed sensor

lead.

Between speed sensor coupler
and ECU coupler.
(blueblue)
(white/yellowwhite/yellow)
Starting the engine, and activating the

vehicle speed
sensor by operating the vehicle at 20 to 30
km/h.
A-3
Gear for detecting vehicle speed has

broken.
Refer to TRANSMISSION on
page 5-107.
A-4
Defective speed sensor.

(Code No.07)
SPEED SENSOR on page
7-88.
7-57

Fault code No.
42
Diagnostic code No.
Symptom A. No normal signals are received from the speed sensor.

B. Open circuit is detected in the neutral switch.
A
07
Speed sensor
21
Neutral switch

cause
Reinstatement
method
B-1
Connections
Neutral switch coupler

the coupler.
B-2
Open circuit in neutral switch lead.

open circuit.
Between neutral switch coupler
and relay unit coupler (fuel
pump relay).
(sky bluesky blue)
Between relay unit coupler and
main switch.
(blue/yellowblue/yellow)
Between main switch and ECU
coupler.
(blue/blackblue/black)
Starting the engine, and activating the

vehicle speed
sensor by operating the vehicle at 20 to 30
km/h.
B-3
Faulty shift drum (neutral detection ar- Replace if defective.

ea).
Refer to TRANSMISSION on
page 5-107.
B-4
Defective neutral switch.

(Code No.21)
7-58

Fault code No.
43
Diagnostic code No.
Symptom The ECU is unable to monitor the battery voltage (an open
or short circuit in the line to the ECU).
09
Fuel system voltage

cause
Connections
Relay unit coupler (fuel pump relay)
Check the coupler for any pins Starting the enthat may be pulled out.
gine and oper Check the locking condition of
ating it at idle.
the coupler.
Open or short circuit in the wire harness.

Between relay unit coupler (fuel
pump relay) and ECU coupler.
(blue/redblue/red)
(red/bluered/blue)
pump relay) and battery terminal.
(redred)
pump relay) and diode 2 coupler.
(red/whitered/white)
Between diode 2 coupler and
engine stop switch coupler.
(black/redblack/red)
Malfunction or open circuit in relay

unit (fuel pump relay).

(Code No. 09)
If there is no malfunction with
the relay unit (fuel pump relay),
replace the ECU.
Fault code No.
44
Diagnostic code No.
Reinstatement
method
Symptom Error is detected while reading or writing on EEPROM (CO

adjustment value).
60
EEPROM improper cylinder indication

cause
Reinstatement
method

(Code No. 60)
1. Check the faulty cylinder. (If
multiple cylinders are defective, the number of the faulty
cylinders appears alternately at 2-second intervals.)
Replace ECU if defective.
Turning the
main switch to
ON.
Malfunction in ECU.
7-59

Fault code No.
46
Diagnostic code No.
Symptom Power supply to the fuel injection system is not normal.

cause
Connections
Check the coupler for any pins Starting the enthat may be pulled out.
gine and oper Check the locking condition of
ating it at idle.
the coupler.
Faulty battery.
Replace or charge the battery

page 7-76.
Malfunction in rectifier/regulator
Refer to CHARGING SYSTEM on page 7-13.

Between battery and main fuse
(redred)
Between main fuse and main
switch
(redred)
Between main switch and ignition fuse
(brown/bluebrown/blue)
Between ignition fuse and ECU
(red/whitered/white)
Fault code No.
50
Diagnostic code No.
Reinstatement
method
Symptom Faulty ECU memory. (When this malfunction is detected in

the ECU, the fault code number might not appear on the
meter.)

cause
Reinstatement
method
Replace the ECU.
Turning the
main switch to
ON.
Malfunction in ECU.
NOTE:
Do not perform this procedure

with the main switch turned to
ON.
7-60

Fault code No.
Er-1 Symptom No signals are received from the ECU.
Diagnostic code No.

cause
Connections
Main wire harness meter assembly
coupler

main switch to
ON.
the coupler.

Between meter assembly coupler and ECU coupler
(yellow/blueyellow/blue)
Malfunction in meter assembly.
Malfunction in ECU.
Replace the ECU.
Fault code No.
Reinstatement
method
Er-2 Symptom No signals are received from the ECU within the specified
duration.
Diagnostic code No.

cause
Connections
coupler

main switch to
ON.
the coupler.

Malfunction in ECU.
Replace the ECU.
7-61
Reinstatement
method

Fault code No.
Er-3 Symptom Data from the ECU cannot be received correctly.
Diagnostic code No.

cause
Connections
coupler

main switch to
ON.
the coupler.

Malfunction in ECU.
Replace the ECU.
Fault code No.
Reinstatement
method
Er-4 Symptom Non-registered data has been received from the meter.
Diagnostic code No.

cause
Connections
coupler

main switch to
ON.
the coupler.

Malfunction in ECU.
Replace the ECU.
7-62
Reinstatement
method
(GRAY)
WW W
7-63
Br
W
W
W
Br B
B R/L
Br
(GRAY)
L/Y L/B
R
Br/L
(BLACK)
Y Br
(BLACK)
L/B L/Y
(GRAY)
Br
Br
A B
Br/L
ON
OFF
(BLACK)
Br/L L/B
L/Y
(BLACK)
W/B L/W
(BLACK)
(BLACK)
L/W W/B
(BLACK)
B B
G/R G/B
Y Br
G/B G/R
R/W B/R
G/L L/B
R/Y
R/Y
Br
R/Y
R/W
R/W R/W R/W R/W
R R/Y
B/R R/W
L/B G/L
R/W
Br/L
Br
R/Y
Br/L
Br/L
R/G
R/B
L Y
B/R
R/Y
L
R/W
W/B
L/W
L/W
B/Y
L/B
L/B
(BLACK)
L Y B
Sb
Sb
Sb/W
PUSH
B L/B
G/B
G/R
L Y/G B/L
(BLACK)
B/L P/Y L
(BLACK)
B/L P/W L
L/B B
G/L
R/L
L/Y L/R
Sb
R/W
L/G
Y
L
B/L
Y/G
L
P/Y
B/L
L
P/W
B/L
B
Y
L
Gy B/L
B/R
E B
E Y
E L
B G
Y B
(BLACK)
(GRAY)
Dg Ch
Br/W
Ch Dg
Br/W
(GRAY)
P B
Y/R
(GRAY)
B P
Y/R
B B
G/Y G/B
(BLUE)
G
G/L
Br
(BLACK)
(GRAY)
(GRAY)
Br B
B B
B/L
Y/B
Br
B
B
(BLACK)
L/Y B/Y
G/W
W L
B
Br
R/Y
R/Y
G/L
L W/Y
B/L
(BLACK)
(GRAY)
B/Y L/Y
G/B G/Y
(BLACK)
(BLUE)
G
G/L
B/L
Gy
(BLUE)
R/L
R/W L/W R/L

Sb B/Y Sb/W
Br/W B/L
L/G L/Y
B L/G
B
(BLUE)
B Gy
L/R R/Y
L/G
B/R
R/W
Ch
Y/B
G/L
Br B Br
Br/W
(L)
N
(R)
Dg
Br/W
Ch
Br
Y/G
B/Y
R/L
L/R
R/B
R/B
Br/W
Br
P/W
P/Y
L/W
B/L
Y
L
W/Y
R/W
L/B
Gy
Y/R
Br/W Y/R
B
Ch A Ch
Dg A Dg
Dg
G/L
B/L
L
W/Y
G/W B
R/L B
B
B
Gy/R
G
Gy Y/B Gy/R
O
O
W/Y Y/R
Br
Br/W
W/Y
PUSH
Ch L
G/B
G/Y
P
Br
(BLACK)
B/Br B
B/Br B
Ch L
B
(GRAY)
Br
(GRAY)
L Ch
B
G
Gy
Y/B
Gy/G
Gy/W
Y/L
W/R
B/G
B/R
R/G
P/L
W/G
Br/L
O
O
Gy/R
Gy/R
Dg L
R/B
R/B
D D
R/B
R/B
R/B
R/B
B/W
W/G R/B R/G

Br/L R/B P/L
R/G
P/L
W/G
Br/L
L Dg
Dg L
B
B
(BLACK) (BLACK)
R/G D R/G
P/L D P/L
W/G D W/G
Br/L D Br/L
Gy/R C Gy/R
Gy/R C Gy/R
Gy/G L/B
Br/W P/Y W/R L
L/W W/Y
Y/G Br
P/W L/R
Gy/W B/R
B/G
B G
G B G
Gy B Gy
B/G
B/R
Gy/R
B/R
Gy/R
B/R
B/R
B/L
Gy/W
(BLACK)
Gy/W R/L
Gy/G B/L
R/L
B B
W L
W Gy
(GRAY)
B
(DARK GRAY)
W B
W
W G
(BLACK)
L W/R B/L
B/G B/R
Gy/G
Gy
L
W/R
B/L
B/R
B/R
C
B/R
Dg
Ch
R/G
Y/L
G/W
G
R/W
G/R
G/Y
G/B
Dg
B
G
W
Br
B
Dg
B
L
Ch
Y
Br
B
G Gy
W W
(BLACK)
R/G R/B W/G

P/L R/B Br/L
L Y
B
G/Y G/R
G/B
G/R G/Y
G/B
(BLACK)
R/G G/W Y/L

B G
Y/L G/W R/G
G B
(BLACK)
Dg L Y
Ch Sb/W R/W
Sb/W
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS4
Y
L Dg
R/W Sb Ch
WIRE HARNESS
WIRE HARNESS
(BLACK)
W/G R/B R/G

Br/L R/B P/L
SUB-WIRE-HARNESS3
(BLACK)
WIRE HARNESS
Gy/R B/R Gy/R

(BLACK)
SUB-WIRE-HARNESS2
SUB-WIRE-HARNESS1
Gy/R B/R Gy/R
WIRE HARNESS
Gy
W
WIRE HARNESS
Ch
Y
FUEL PUMP SYSTEM
EAS27550
FUEL PUMP SYSTEM
EAS27560
CIRCUIT DIAGRAM
FUEL PUMP SYSTEM

3. Main switch
4. Main fuse
6. Battery
11.Relay unit
13.Fuel pump relay
15.Diode 2
17.Fuel pump
77.Ignition fuse
81.ECU fuse
7-64
FUEL PUMP SYSTEM

EAS27570
TROUBLESHOOTING
If the fuel pump fails to operate.
NOTE:

1. Rider seat
2. Tool kit tray
4. Left side cover
1. Check the fuses.
(Main, fuel injection system, ignition
and ECU)
NG
OK
page 7-76.
NG
OK
NG
OK
4. Check the engine stop switch.
NG

OK
5. Check the relay unit (fuel pump relay).
NG
OK
NG
OK
7. Check the fuel pump.
PUMP on page 7-89.
NG
OK
7-65
FUEL PUMP SYSTEM

8. Check the entire fuel pump system
wiring.
page 7-63.
NG
Properly connect or repair the fuel pump
system wiring.
OK
Replace the ECU.
7-66
ELECTRICAL COMPONENTS
EAS27970
3
4
6
14
9
13
10
12
11
7-67
3. Fuel sender
8. EXUP servo motor
9. Speed sensor
11. Neutral switch
12. Horn 2
13. Horn 1
7-68
18
10
8
17
11
12
13
14
16
15
9
7-69
2. Main switch
6. Fuse box
7. Starter relay
9. Battery
10. Diode 2
12. Headlight relay
13. Relay unit
14. Diode 1
15. Main fuse
16. Lean angle cut-off switch
7-70
EAS27980
CHECKING THE SWITCHES
1
R Br L/Y L/B
ON
Br
OFF
L/B L/Y
(GRAY)
2
R/W B/R
14
G
G/L
(BLUE)
Ch Br/W Dg B Y/R
(L)
R/W B/R
G/L L/B
B B
G/Y G/B
(GRAY)
(R)
P B
Y/R
(GRAY)
13
G/Y G/B
L/W W/B
B B
G/R G/B
(BLACK)
L/W W/B
L/B G/L
(BLACK)
Ch Dg
Br/W
(GRAY)
PUSH
12
5
G/B G/R
Y G/L G
PUSH
11
6
B P
10
Br
L/Y B/Y
B
B
(BLACK)
8
B B
(BLACK)
B B
(BLUE)
7-71
1. Main switch
3. Start switch
4. Accessory light switch
5. Reset switch
6. Front brake light switch
7. Neutral switch
8. Sidestand switch
10. Clutch switch
11. Horn switch
12. Dimmer switch
13. Select switch
14. Turn signal switch
7-72
Check each switch for continuity with the pocket tester. If the continuity reading is incorrect, check the
wiring connections and if necessary, replace the switch.
ECA14370
CAUTION:
Never insert the tester probes into the coupler terminal slots a. Always insert the probes from
the opposite end of the coupler, taking care not to loosen or damage the leads.
Pocket tester
90890-03112
YU-03112-C
NOTE:
Before checking for continuity, set the pocket tester to 0 and to the 1 range.
When checking for continuity, switch back and forth between the switch positions a few times.
The switches and their terminal connections are illustrated as in the following example of the main
switch.
The switch positions a are shown in the far left column and the switch lead colors b are shown in the
top row.
The continuity (i. e., a closed circuit) between switch terminals at a given switch position is indicated by
. There is continuity between red and brown, blue/yellow and blue/black when the switch is
set to ON.
b
R Br L/Y L/B
ON
OFF
R
Br
7-73
L/B L/Y
1. Remove:
Bulb
EAS27990
CHECKING THE BULBS AND BULB

SOCKETS
EW1D71009
WARNING
NOTE:
Do not check any of the lights that use LEDs.
Since headlight bulbs get extremely hot,

away from them until they have cooled
down.
Check each bulb and bulb socket for damage or

wear, proper connections, and also for continuity
between the terminals.
Damage/wear Repair or replace the bulb,
bulb socket or both.
Improperly connected Properly connect.
No continuity Repair or replace the bulb, bulb
socket or both.
EC1D71006
CAUTION:
Be sure to hold the socket firmly when removing the bulb. Never pull the lead, otherwise it may be pulled out of the terminal in
the coupler.
Avoid touching the glass part of a headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the life of the
bulb, and the luminous flux will be adversely affected. If the headlight bulb gets soiled,
Types of bulbs
The bulbs used on this vehicle are shown in the
illustration.
Bulbs a and b are used for the headlights
and usually use a bulb holder that must be detached before removing the bulb. The majority
of these types of bulbs can be removed from
their respective socket by turning them counterclockwise.
Bulbs c are used for turn signal and tail/brake
lights and can be removed from the socket by
pushing and turning the bulb counterclockwise.
Bulbs d and e are used for meter and indicator lights and can be removed from their respective socket by carefully pulling them out.
2. Check:
Bulb (for continuity)
No continuity Replace.
Pocket tester
90890-03112
YU-03112-C
NOTE:
Before checking for continuity, set the pocket

tester to 0 and to the 1 range.
a. Connect the positive tester probe to terminal

1 and the negative tester probe to terminal
2, and check the continuity.
b. Connect the positive tester probe to terminal
1 and the negative tester probe to terminal
3, and check the continuity.
c. If either of the readings indicate no continuity,
replace the bulb.
Checking the condition of the bulbs

bulbs.
7-74
NOTE:
Set the pocket tester selector to 1.

Pocket tester
90890-03112
YU-03112-C
b. If the pocket tester indicates , replace the
fuse.
Checking the condition of the bulb sockets

The following procedure applies to all of the bulb
sockets.
1. Check:
Bulb socket (for continuity)
No continuity Replace.
3. Replace:
Blown fuse
a. Turn the main switch to OFF.

b. Install a new fuse of the correct amperage
rating.
c. Set on the switches to verify if the electrical
circuit is operational.
d. If the fuse immediately blows again, check
the electrical circuit.
Pocket tester
90890-03112
YU-03112-C
Fuses
Amperage
rating
Qty
Main
50 A
Ignition
25 A
Headlight
20 A
Fuel injection system
15 A
Signaling system
10 A
Taillight
10 A
ECU
10 A
Backup (odometer and

clock)
10 A
Auxiliary DC connector
3A
Spare
25 A
Spare
20 A
NOTE:
Check each bulb socket for continuity in the

same manner as described in the bulb section;
however, note the following.
a. Install a good bulb into the bulb socket.

b. Connect the pocket tester probes to the respective leads of the bulb socket.
c. Check the bulb socket for continuity. If any of
the readings indicate no continuity, replace
the bulb socket.
EAS28000
CHECKING THE FUSES

The following procedure applies to all of the fuses.
Spare
15 A
CAUTION:
Spare
10 A
To avoid a short circuit, always turn the main

switch to OFF when checking or replacing
a fuse.
Spare
3A
EC1D71019
EWA13310
WARNING
1. Remove:
Rider seat
2. Check:
Fuse
Never use a fuse with an amperage rating

other than that specified. Improvising or using a fuse with the wrong amperage rating
may cause extensive damage to the electri-
a. Connect the pocket tester to the fuse and

check the continuity.
7-75
electrolyte level will drop considerably.
Therefore, take special care when charging
the battery.
cal system, cause the lighting and ignition

systems to malfunction and could possibly
cause a fire.
NOTE:
4. Install:
Rider seat
Since MF batteries are sealed, it is not possible

to check the charge state of the battery by measuring the specific gravity of the electrolyte.
Therefore, the charge of the battery has to be
checked by measuring the voltage at the battery
terminals.
EAS28030
CHECKING AND CHARGING THE BATTERY

EWA13290
WARNING
1. Remove:
Rider seat
2. Remove:
ECU band 1
Batteries generate explosive hydrogen gas

and contain electrolyte which is made of poisonous and highly caustic sulfuric acid.
Therefore, always follow these preventive
measures:
Wear protective eye gear when handling or
working near batteries.
Charge batteries in a well-ventilated area.
Keep batteries away from fire, sparks or
open flames (e.g., welding equipment,
lighted cigarettes).
DO NOT SMOKE when charging or handling batteries.
KEEP BATTERIES AND ELECTROLYTE
OUT OF REACH OF CHILDREN.
Avoid bodily contact with electrolyte as it
can cause severe burns or permanent eye
injury.
FIRST AID IN CASE OF BODILY CONTACT:
EXTERNAL
Skin Wash with water.
Eyes Flush with water for 15 minutes and
get immediate medical attention.
INTERNAL
Drink large quantities of water or milk followed with milk of magnesia, beaten egg or
vegetable oil. Get immediate medical attention.
3. Remove:
Coupler tray 1
1
4. Disconnect:
Battery leads
(from the battery terminals)
EC1D71020
CAUTION:
ECA13640
CAUTION:
This is a sealed battery. Never remove the

sealing caps because the balance between
cells will not be maintained and battery performance will deteriorate.
Charging time, charging amperage and
charging voltage for an MF battery are different from those of conventional batteries.
The MF battery should be charged according to the instructions for the charging
method. If the battery is overcharged, the
First, disconnect the negative battery lead

1, and then positive battery lead 2.
7-76
2
5. Remove:
Battery
6. Check:
Battery charge
A. Open-circuit voltage (V)

B. Charging condition of the battery (%)
C. Ambient temperature 20 C (68 F)
a. Connect a pocket tester to the battery terminals.

positive battery terminal
negative battery terminal
7. Charge:
Battery
(refer to the appropriate charging method illustration)
NOTE:
Do not quick charge a battery.
EWA13300
WARNING
The charge state of an MF battery can be

checked by measuring its open-circuit voltage
(i.e., the voltage when the positive battery terminal is disconnected).
No charging is necessary when the open-circuit voltage equals or exceeds 12.8 V.
ECA13670
CAUTION:
Never remove the MF battery sealing caps.

Do not use a high-rate battery charger
since it forces a high-amperage current
into the battery quickly and can cause battery overheating and battery plate damage.
If it is impossible to regulate the charging
current on the battery charger, be careful
not to overcharge the battery.
When charging a battery, be sure to remove
it from the vehicle. (If charging has to be
done with the battery mounted on the vehicle, disconnect the negative battery lead
from the battery terminal.)
To reduce the chance of sparks, do not
plug in the battery charger until the battery
charger leads are connected to the battery.
Before removing the battery charger lead
clips from the battery terminals, be sure to
turn off the battery charger.
Make sure the battery charger lead clips are
in full contact with the battery terminal and
that they are not shorted. A corroded battery charger lead clip may generate heat in
the contact area and a weak clip spring may
cause sparks.
b. Check the charge of the battery, as shown in

the charts and the following example.
Example
Open-circuit voltage = 12.0 V
Charging time = 6.5 hours
Charge of the battery = 2030%
A. Open-circuit voltage (V)

B. Charging time (hours)
C. Relationship between the open-circuit voltage
and the charging time at 20 C (68 F)
D. These values vary with the temperature, the
condition of the battery plates, and the
electrolyte level.
7-77
If the battery becomes hot to the touch at
any time during the charging process, disconnect the battery charger and let the battery cool before reconnecting it. Hot
batteries can explode!
As shown in the following illustration, the
open-circuit voltage of an MF battery stabilizes about 30 minutes after charging has
been completed. Therefore, wait 30 minutes after charging is completed before
measuring the open-circuit voltage.
Standard charging current is reached

Battery is good.
Standard charging current is not reached
Replace the battery.
d. Adjust the voltage so that the current is at the
standard charging level.
e. Set the time according to the charging time
suitable for the open-circuit voltage.
f. If charging requires more than 5 hours, it is
advisable to check the charging current after
a lapse of 5 hours. If there is any change in
the amperage, readjust the voltage to obtain
the standard charging current.
g. Measure the battery open-circuit voltage after
leaving the battery unused for more than 30
minutes.
12.8 V or more --- Charging is complete.
12.7 V or less --- Recharging is required.
Under 12.0 V --- Replace the battery.
A.
B.
C.
D.
E.
Open-circuit voltage (V)

Time (minutes)
Charging
Ambient temperature 20 C (68 F)
Check the open-circuit voltage.
Charging method using a constant voltage charger

a. Measure the open-circuit voltage prior to
charging.
NOTE:
Voltage should be measured 30 minutes after

the engine is stopped.
Charging method using a variable-current

(voltage) charger
a. Measure the open-circuit voltage prior to
charging.
b. Connect a charger and ammeter to the battery and start charging.

c. Make sure that the current is higher than the
standard charging current written on the battery.
NOTE:
Voltage should be measured 30 minutes after

the engine is stopped.
b. Connect a charger and ammeter to the battery and start charging.
NOTE:
If the current is lower than the standard charging

current written on the battery, this type of battery
charger cannot charge the MF battery. A variable voltage charger is recommended.
NOTE:
Set the charging voltage at 1617 V. If the setting is lower, charging will be insufficient. If too
high, the battery will be over-charged.
d. Charge the battery until the batterys charging voltage is 15 V.
c. Make sure that the current is higher than the

standard charging current written on the battery.
NOTE:
NOTE:
e. Measure the battery open-circuit voltage after

leaving the battery unused for more than 30
minutes.
Set the charging time at 20 hours (maximum).
If the current is lower than the standard charging

current written on the battery, set the charging
voltage adjust dial at 2024 V and monitor the
amperage for 35 minutes to check the battery.
7-78
12.8 V or more --- Charging is complete.
12.7 V or less --- Recharging is required.
Under 12.0 V --- Replace the battery.
Pocket tester
90890-03112
YU-03112-C
8. Install:
Battery
9. Connect:
Battery leads
(to the battery terminals)
1. Disconnect the relay from the wire harness.

2. Connect the pocket tester ( 1) and battery
(12 V) to the relay terminals as shown.
Check the relay operation.
ECA13630
CAUTION:
Starter relay
First, connect the positive battery lead 1,

and then the negative battery lead 2.
NOTE:
Be sure to route the negative battery lead towards the front of the vehicle and to install the
negative terminal cover 3 securely.
R
R/Y
3
1.
2.
3.
4.
Positive battery terminal

Negative battery terminal
Result
Continuity
(between 3 and 4)
10.Check:
Battery terminals
Dirt Clean with a wire brush.
11.Lubricate:
Battery terminals
Relay unit (starting circuit cut-off relay)
Dielectric grease
1 2
12.Install:
Coupler tray
ECU band
NOTE:
Make sure the leads are routed correctly.
1.
2.
3.
4.
13.Install:
Rider seat

Result
Continuity
(between 3 and 4)
EAS28040
CHECKING THE RELAYS

Check each switch for continuity with the pocket
tester. If the continuity reading is incorrect, replace the relay.
7-79
Relay unit (fuel pump relay)
1.
2.
3.
4.
a. Connect the pocket tester (DC 20 V) to the

turn signal relay terminal as shown.
Pocket tester
90890-03112
YU-03112-C
brown 1
ground

Result
Continuity
(between 3 and 4)
Headlight relay
3
4
b. Turn the main switch to ON.

c. Measure the turn signal relay input voltage.
2. Check:
Turn signal relay output voltage
1
Y/B
Br
G/L
R/Y
1.
2.
3.
4.
Turn signal relay output voltage

DC 12 V


turn signal relay terminal as shown.
Pocket tester
90890-03112
YU-03112-C
Result
Continuity
(between 3 and 4)

brown/white 1, yellow/red 2 or white/yellow 3
ground
ET1D71011
CHECKING THE TURN SIGNAL RELAY

1. Check:
Turn signal relay input voltage
Out of specification The wiring circuit from
the main switch to the turn signal relay coupler is faulty and must be repaired.
Turn signal relay input voltage
DC 12 V
7-80
Continuity
Positive tester probe sky blue
1
black/yellow 2
No continuity
black/yellow 2
Negative tester probe sky
blue 1
Continuity
1
blue/yellow 3
No continuity
blue/yellow 3
blue 1
Continuity
1
blue/white 4
No continuity
Positive tester probe sky
blue/white 4
blue 1
Continuity
blue/green 5
blue/yellow 3
No continuity
blue/yellow 3
blue/green 5

c. Measure the turn signal relay output voltage.
EAS28050
CHECKING THE DIODES

Relay unit (diode)
1. Check:
Relay unit (diode)
Pocket tester
90890-03112
YU-03112-C
NOTE:
The pocket tester or the analog pocket tester

readings are shown in the following table.
5 3 1
2 4
a. Disconnect the relay unit from the wire harness.

b. Connect the pocket tester ( 1) to the relay
unit terminals as shown.
7-81
c. Check the relay unit (diode) for continuity.
d. Check the relay unit (diode) for no continuity.
Pocket tester
90890-03112
YU-03112-C
Diode 1
1. Check:
Diode 1
NOTE:
The pocket tester and the analog pocket tester

Pocket tester
90890-03112
YU-03112-C
Continuity
red/white 1
black/red 2
No continuity
black/red 2
red/white 1
NOTE:
The pocket tester and the analog pocket tester

Continuity
Positive tester probe red/yellow 1
red/white 2 or red/white 3
No continuity
red/white 2 or red/white 3
Negative tester probe red/yellow 1
1
R/W
B/R
2
a. Disconnect the diode 2 from the wire harness.

b. Connect the pocket tester ( 1) to the diode
2 terminals as shown.
c. Check the diode 2 for continuity.
d. Check the diode 2 for no continuity.
R/W R/W
R/Y
1
a. Disconnect the diode 1 from the wire harness.

b. Connect the pocket tester ( 1) to the diode
1 terminals as shown.
c. Check the diode 1 for continuity.
d. Check the diode 1 for no continuity.
ET1D71012
CHECKING THE IGNITION SPARK GAP

1. Check:
Ignition spark gap
Out of specification Perform the ignition
system troubleshooting, starting with step 5.
Refer to TROUBLESHOOTING on page
7-4.
Diode 2
1. Check:
Diode 2
Minimum ignition spark gap

6.0 mm (0.24 in)
NOTE:
If the ignition spark gap is within specification,

the ignition system circuit is operating normally.
7-82
a. Disconnect the spark plug cap from the spark

plug.
b. Connect the ignition checker 1 as shown.
Ignition checker
90890-06754
Opama pet-4000 spark checker
YM-34487
c. Measure the spark plug cap resistance.
EAS28100
CHECKING THE IGNITION COILS

The following procedure applies to all of the ignition coils.
1. Check:
2. Spark plug cap

2.162.64
c. Turn the main switch to ON and engine stop

switch to .
d. Measure the ignition spark gap a.
e. Crank the engine by pushing the start switch
and gradually increase the spark gap until a misfire occurs.
a. Disconnect the ignition coil connectors from

the ignition coil terminals.
b. Connect the pocket tester ( 1) to the ignition coil as shown.
Pocket tester
90890-03112
YU-03112-C
EAS28070
CHECKING THE SPARK PLUG CAPS

spark plug caps.
1. Check:
Spark plug cap resistance

black/red 1
orange or gray/red 2
Resistance
10.0 k
a. Remove the spark plug cap from the spark

plug lead.
b. Connect the pocket tester ( 1k) to the
spark plug cap as shown.
Pocket tester
90890-03112
YU-03112-C
c. Measure the primary coil resistance.
2. Check:
7-83
gray 1
black 2

8.6412.96 k
a. Disconnect the spark plug cap from the ignition coil.

b. Connect the pocket tester ( 1k) to the ignition coil as shown.
Pocket tester
90890-03112
YU-03112-C
B Gy

black/red 1
spark plug lead 2
b. Measure the crankshaft position sensor resistance.
EAS28130
CHECKING THE LEAN ANGLE SENSOR

1. Remove:
Lean angle sensor
2. Check:
Lean angle sensor output voltage
Lean angle sensor output voltage
Less than 65: 0.41.4 V
More than 65: 3.74.4 V
c. Measure the secondary coil resistance.
a. Connect the lean angle sensor coupler to the

wire harness.
b. Connect the pocket tester (DC 20 V) to the
lean angle sensor coupler as shown.
EAS28120
CHECKING THE CRANKSHAFT POSITION

SENSOR
1. Disconnect:
(from the wire harness)
2. Check:
Out of specification Replace the crankshaft position sensor.
Pocket tester
90890-03112
YU-03112-C
yellow/green 1
black/blue 2

248372
a. Connect the pocket tester ( 100) to the

crankshaft position sensor coupler as shown.
Pocket tester
90890-03112
YU-03112-C
7-84
EAS28150
CHECKING THE STATOR COIL

1. Disconnect:
Stator coil coupler
(from the rectifier/regulator)
2. Check:
Out of specification Replace the stator coil.
0.1120.168
c. Turn the lean angle sensor to 65.

d. Measure the lean angle sensor output voltage.
a. Connect the pocket tester ( 1) to the stator

coil coupler as shown.
Pocket tester
90890-03112
YU-03112-C
ET1D71013
CHECKING THE STARTER MOTOR

OPERATION
1. Check:
Starter motor operation
Does not operate Perform the electric
starting system troubleshooting, starting with
step 5.
Refer to TROUBLESHOOTING on page
7-11.

white 1
white 2
white 1
white 3
a. Connect the positive battery terminal 1 and

starter motor lead 2 with a jumper lead 3.
EWA13810
WARNING

white 2
white 3
A wire that is used as a jumper lead must

have at least the same capacity of the battery lead, otherwise the jumper lead may
burn.
This check is likely to produce sparks,
therefore, make sure no flammable gas or
fluid is in the vicinity.
W W W
1 2 3
b. Measure the stator coil resistance.
EAS28170
b. Check the starter motor operation.
CHECKING THE RECTIFIER/REGULATOR

1. Check:
Charging voltage
Out of specification Replace the rectifier/regulator.
7-85
horn terminal 1
horn terminal 2
Charging voltage
14 V at 5000 r/min
a. Set the engine tachometer to the cylinder-#1

left spark plug lead or right spark plug lead.
b. Connect the pocket tester (DC 20 V) to the
rectifier/regulator coupler as shown.
Pocket tester
90890-03112
YU-03112-C
red 1
black 2
W W W
A. Horn 1
B. Horn 2
c. Measure the horn resistance.
c. Start the engine and let it run at approximately 5000 r/min.

d. Measure the charging voltage.
2. Check:
Horn sound
Faulty sound Adjust or replace.
EAS28180
a. Connect a battery (12 V) to the horn.

b. Turn the adjusting screw in direction a or b
until the horn sound is obtained.
CHECKING THE HORNS

1. Check:
Horn resistance
Coil resistance
0.940.98
a. Disconnect the horn 1 connectors and horn 2

coupler from the horn terminals.
b. Connect the pocket tester ( 1) to the horn
terminals.
Pocket tester
90890-03112
YU-03112-C
7-86
A
3
a
2
b. Immerse the engine temperature sensor 1
in a container filled with water 2.
NOTE:
Make sure that the engine temperature sensor

terminals do not get wet.
c. Place a thermometer 3 in the water.
d. Slowly heat the water, then let it cool down to
the specified temperature.
e. Measure the engine temperature sensor resistance.
A. Horn 1
B. Horn 2
3. Install:
EAS28210
T.
CHECKING THE ENGINE TEMPERATURE

SENSOR
1. Remove:
(from the front cylinder head)
R.

20 Nm (2.0 mkg, 14 ftlb)
ET1D71014
CHECKING THE FUEL SENDER (FUEL

TANK)
1. Remove:
Fuel sender
(from the fuel tank)
2. Check:
Fuel sender resistance
EWA14140
WARNING
Handle the engine temperature sensor with

special care.
Never subject the engine temperature sensor to strong shocks. If the engine temperature sensor is dropped, replace it.
2. Check:
Fuel sender (fuel tank)

Sender unit resistance (full)
911
Sender unit resistance (empty)
213219

0.901.10 k at 100 C (212 F)
a. Connect the pocket tester ( 100) to the

fuel sender coupler as shown.
a. Connect the pocket tester ( 1 k) to the engine temperature sensor terminals as shown.
Pocket tester
90890-03112
YU-03112-C
Pocket tester
90890-03112
YU-03112-C
7-87
green 1
black 2
b. Move the fuel sender float to maximum

3/minimum 4 level position.
1
G/W
R/L
3
1
b. Measure the fuel sender resistance.
G B
ET1D71044
CHECKING THE FUEL LEVEL WARNING

LIGHT
This model is equipped with a self-diagnosis device for the fuel level detection circuit.
1. Check:
Fuel level warning light 1
(Turn the main switch to ON.)
Warning light comes on for a few seconds,
then goes off Warning light is OK.
Warning light does not come on Replace
the meter assembly.
Warning light flashes eight times, then goes
off for three seconds in a repeated cycle (malfunction detected in fuel sender or thermistor)
4
c. Measure the fuel sender resistance.
ET1D71015
CHECKING THE FUEL SENDER (FUEL

PUMP)
1. Drain the fuel.
2. Disconnect:
Fuel pump coupler
(from the fuel pump)
3. Remove:
Fuel pump
(from the sub-fuel tank)
4. Check:
Out of specification Replace the fuel pump
assembly.
0.902.05 k
a. Connect the pocket tester ( 1) to the fuel

sender terminals as shown.
EAS28240
CHECKING THE SPEED SENSOR

1. Check:
Speed sensor output voltage
Pocket tester
90890-03112
YU-03112-C
Output voltage reading cycle

0.6 V to 4.8 V to 0.6 V to 4.8 V

green/white 1
black 2

speed sensor coupler as shown.
7-88
Pocket tester
90890-03112
YU-03112-C

white 1
black 2
B Y L
b. Measure the throttle position sensor maximum resistance.
3. Install:
L W/Y
NOTE:
B/ L
When installing the throttle position sensor, adjust its angle properly. Refer to ADJUSTING
THE THROTTLE POSITION SENSOR on page
6-12.
2
c. Elevate the rear wheel and slowly rotate it.
d. Measure the voltage of white and black. With
each full rotation of the rear wheel, the voltage reading should cycle from 0.6 V to 4.8 V
to 0.6 V to 4.8 V.
EAS28350
CHECKING THE FUEL PUMP

EWA13850
WARNING
EAS28300
CHECKING THE THROTTLE POSITION

SENSOR
1. Remove:
(from the throttle body)
2. Check:
Throttle position sensor maximum resistance
Out of specification Replace the throttle
position sensor.
Resistance
4.06.0 k/blue-black
Gasoline is extremely flammable and under

certain circumstances there can be a danger
of an explosion or fire. Be extremely careful
and note the following points:
Stop the engine before refueling.
Do not smoke, and keep away from open
flames, sparks, or any other source of fire.
If you do accidentally spill gasoline, wipe it
up immediately with dry rags.
If gasoline touches the engine when it is
hot, a fire may occur. Therefore, make sure
the engine is completely cool before performing the following test.
1. Disconnect:
Fuel pump coupler
(from the fuel pump)
2. Check:
Fuel pump operation
Faulty/rough movement Replace.
a. Connect the pocket tester ( 1k) to the

throttle position sensor terminals as shown.
Pocket tester
90890-03112
YU-03112-C
a. Fill the fuel tank.

b. Put the end of the fuel hose 1 into an open
container.
c. Connect the battery (DC 12 V) to the fuel
pump terminals as shown.

blue 1
black 2
7-89
ECA14390

red/blue 2
black 3
CAUTION:
To prevent damaging the EXUP servo motor,

perform this test within a few seconds of
connecting the battery.
EAS28410
CHECKING THE INTAKE AIR PRESSURE

SENSOR
The following procedure applies to both of the intake air pressure sensors.
1. Check:
Intake air pressure sensor output voltage
G/W B
R/L
d. Check the fuel pump operation.
Intake air pressure sensor output

voltage
3.754.25 V
EAS28360
CHECKING THE EXUP SERVO MOTOR

1. Check:
EXUP servo motor operation
a. Connect the pocket tester (DC 20 V) to the intake air pressure sensor coupler as shown.
Pocket tester
90890-03112
YU-03112-C
a. Disconnect the EXUP cables from the EXUP

servo motor pulley.
b. Disconnect the EXUP servo motor coupler
from the wire harness.
c. Connect the battery leads to the EXUP servo
motor terminals as shown.
For counterclockwise rotation a
black/green 1
black/red 2
For clockwise rotation b
black/red 2
black/green 1

pink/white 1 or pink/yellow
black/blue 2
B/L P/W L
2
c. Measure the intake air pressure sensor output voltage.
L W/R B/L
B/G B/R
ET1D71016
CHECKING THE AIR TEMPERATURE

SENSOR
1. Remove:
d. Check that the EXUP servo motor pulley rotates several times in directions a and b.
7-90
EW1D71004
WARNING
Handle the air temperature sensor with

special care.
Never subject the air temperature sensor to
strong shocks. If the air temperature sensor is dropped, replace it.
2. Check:
Air temperature sensor resistance
Air temperature sensor resistance
290390 at 80 C (176 F)
a. Connect the pocket tester ( 100) to the air

temperature sensor terminals as shown.
Pocket tester
90890-03112
YU-03112-C
3
1
2
b. Immerse the air temperature sensor 1 in a
container filled with water 2.
NOTE:
Make sure that the air temperature sensor terminals do not get wet.
c. Place a thermometer 3 in the water.
d. Slowly heat the water, then let it cool down to
the specified temperature.
e. Measure the air temperature sensor resistance.
7-91
TROUBLESHOOTING
TROUBLESHOOTING .................................................................................... 8-1
GENERAL INFORMATION ....................................................................... 8-1
STARTING FAILURES ............................................................................. 8-1
INCORRECT ENGINE IDLING SPEED .................................................... 8-1
POOR MEDIUM AND HIGH-SPEED PERFORMANCE ........................... 8-2
FAULTY GEAR SHIFTING ....................................................................... 8-2
SHIFT PEDAL DOES NOT MOVE............................................................ 8-2
JUMPS OUT OF GEAR ............................................................................ 8-2
FAULTY CLUTCH ..................................................................................... 8-2
OVERHEATING ........................................................................................ 8-3
POOR BRAKING PERFORMANCE.......................................................... 8-3
FAULTY FRONT FORK LEGS.................................................................. 8-3
UNSTABLE HANDLING............................................................................ 8-3
FAULTY LIGHTING OR SIGNALING SYSTEM........................................ 8-4
TROUBLESHOOTING
Sucked-in air
EAS28450
TROUBLESHOOTING
Electrical system
1. Battery
Discharged battery
Faulty battery
2. Fuse(s)
Blown, damaged or incorrect fuse
Improperly installed fuse
3. Spark plug(s)
Incorrect spark plug gap
Incorrect spark plug heat range
Fouled spark plug
Worn or damaged electrode
Worn or damaged insulator
Faulty spark plug cap
4. Ignition coil(s)
Cracked or broken ignition coil body
Broken or shorted primary or secondary coils
Faulty spark plug lead
5. Ignition system
Faulty ECU
Faulty crankshaft position sensor
Broken generator rotor woodruff key
6. Switches and wiring
Faulty main switch
Faulty engine stop switch
Broken or shorted wiring
Faulty neutral switch
Faulty start switch
Faulty sidestand switch
Faulty clutch switch
Improperly grounded circuit
Loose connections
7. Starting system
Faulty starter motor
Faulty starter relay
Faulty relay unit (starting circuit cut-off relay)
Faulty starter clutch
EAS28460
GENERAL INFORMATION
NOTE:
The following guide for troubleshooting does not

cover all the possible causes of trouble. It should
be helpful, however, as a guide to basic troubleshooting. Refer to the relative procedure in this
manual for checks, adjustments, and replacement of parts.
EAS28470
STARTING FAILURES
Engine
1. Cylinder(s) and cylinder head(s)
Loose spark plug
Loose cylinder head or cylinder
Damaged cylinder head gasket
Damaged cylinder gasket
Worn or damaged cylinder
Incorrect valve clearance
Improperly sealed valve
Incorrect valve-to-valve-seat contact
Incorrect valve timing
Faulty valve spring
Seized valve
2. Piston(s) and piston ring(s)
Improperly installed piston ring
Damaged, worn or fatigued piston ring
Seized piston ring
Seized or damaged piston
3. Air filter
Improperly installed air filter
Clogged air filter element
4. Crankcase and crankshaft
Improperly assembled crankcase
Seized crankshaft
EAS28490
INCORRECT ENGINE IDLING SPEED
Fuel system
1. Fuel tank
Empty fuel tank
Clogged fuel filter
Clogged fuel tank overflow/breather hose
Clogged rollover valve
Clogged rollover valve hose
Deteriorated or contaminated fuel
2. Fuel pump
Faulty fuel pump
Faulty relay unit (fuel pump relay)
3. Throttle body(-ies)
Deteriorated or contaminated fuel
Engine
1. Cylinder(s) and cylinder head(s)
Incorrect valve clearance
Damaged valve train components
2. Air filter
Fuel system
Damaged or loose throttle body joint
Improperly synchronized throttle bodies
8-1
TROUBLESHOOTING
Transmission
Seized transmission gear
Foreign object between transmission gears
Improperly assembled transmission
Improper throttle cable free play

Flooded throttle body
Electrical system
1. Battery
Discharged battery
Faulty battery
2. Spark plug(s)
Fouled spark plug
Worn or damaged electrode
Worn or damaged insulator
Faulty spark plug cap
3. Ignition coil(s)
Broken or shorted primary or secondary coils
Faulty spark plug lead
Cracked or broken ignition coil
4. Ignition system
Faulty ECU
Faulty crankshaft position sensor
Broken generator rotor woodruff key
EAS28550
JUMPS OUT OF GEAR

Shift shaft
Incorrect shift pedal position
Improperly returned stopper lever
Shift forks
Worn shift fork
Shift drum
Incorrect axial play
Worn shift drum groove
Transmission
Worn gear dog
EAS28570
FAULTY CLUTCH
EAS28510
POOR MEDIUM AND HIGH-SPEED

PERFORMANCE
Refer to STARTING FAILURES on page 8-1.
Clutch slips
1. Clutch
Improperly assembled clutch
Improperly assembled clutch master cylinder
Improperly assembled clutch release cylinder
Incorrect clutch fluid level
Damaged clutch hose
Loose or fatigued clutch spring
Loose union bolt
Worn friction plate
Worn clutch plate
Damaged clutch release cylinder
2. Engine oil
Incorrect oil level
Incorrect oil viscosity (low)
Deteriorated oil
Engine
1. Air filter
Fuel system
1. Fuel pump
Faulty fuel pump
EAS28530
FAULTY GEAR SHIFTING

Shifting is difficult
Refer to Clutch drags.
Clutch drags
1. Clutch
Air in hydraulic clutch system
Unevenly tensioned clutch springs
Warped pressure plate
Bent clutch plate
Swollen friction plate
Bent clutch push rod
Damaged clutch boss
Burnt primary driven gear bushing
Damaged clutch release cylinder
Match marks not aligned
EAS28540
SHIFT PEDAL DOES NOT MOVE

Shift shaft
Improperly adjusted shift rod
Bent shift shaft
Shift drum and shift forks
Foreign object in a shift drum groove
Seized shift fork
Bent shift fork guide bar
8-2
TROUBLESHOOTING
Damaged oil seal lip
Incorrect oil level (high)
Loose damper rod assembly bolt
Damaged damper rod assembly bolt copper
washer
Cracked or damaged cap bolt O-ring
2. Engine oil
Incorrect oil level
Incorrect oil viscosity (high)
Deteriorated oil
EAS28590
OVERHEATING
Malfunction
Bent or damaged inner tube
Bent or damaged outer tube
Damaged fork spring
Worn or damaged outer tube bushing
Bent or damaged damper rod
Incorrect oil viscosity
Incorrect oil level
Engine
1. Cylinder head(s) and piston(s)
Heavy carbon buildup
2. Engine oil
Incorrect oil level
Incorrect oil viscosity
Inferior oil quality
Fuel system
Faulty throttle body(-ies)
Damaged or loose throttle body joint
2. Air filter
EAS28670
UNSTABLE HANDLING
1. Handlebar
Bent or improperly installed handlebar
2. Steering head components
Improperly installed upper bracket
Improperly installed lower bracket
(improperly tightened ring nut)
Bent steering stem
Damaged ball bearing or bearing race
3. Front fork leg(s)
Uneven oil levels (both front fork legs)
Unevenly tensioned fork spring (both front
fork legs)
Broken fork spring
Bent or damaged inner tube
Bent or damaged outer tube
4. Swingarm
Worn bearing or bushing
Bent or damaged swingarm
5. Rear shock absorber assembly
Faulty rear shock absorber spring
Leaking oil or gas
6. Tire(s)
Uneven tire pressures (front and rear)
Incorrect tire pressure
Uneven tire wear
7. Wheel(s)
Incorrect wheel balance
Deformed cast wheel
Damaged wheel bearing
Bent or loose wheel axle
Excessive wheel runout
8. Frame
Bent frame
Damaged steering head pipe
Improperly installed bearing race
Chassis
1. Brake(s)
Dragging brake
Electrical system
1. Spark plug(s)
2. Ignition system
Faulty ECU
EAS28620
POOR BRAKING PERFORMANCE

Worn brake pad
Worn brake disc
Air in hydraulic brake system
Leaking brake fluid
Faulty brake caliper kit
Faulty brake caliper seal
Loose union bolt
Damaged brake hose
Oil or grease on the brake disc
Oil or grease on the brake pad
Incorrect brake fluid level
EAS28660
FAULTY FRONT FORK LEGS

Leaking oil
Bent, damaged or rusty inner tube
Cracked or damaged outer tube
Improperly installed oil seal
8-3
TROUBLESHOOTING
Faulty turn signal relay
Burnt-out turn signal bulb
EAS28710
FAULTY LIGHTING OR SIGNALING SYSTEM

Headlight does not come on
Wrong headlight bulb
Too many electrical accessories
Hard charging
Incorrect connection
Poor contacts (main switch)
Burnt-out headlight bulb
Horn does not sound

Improperly adjusted horn
Damaged or faulty horn
Faulty main switch
Faulty horn switch
Faulty battery
Faulty wire harness
Headlight bulb burnt out

Wrong headlight bulb
Faulty battery
Faulty rectifier/regulator
Faulty main switch
Headlight bulb life expired
Tail/brake light does not come on
Wrong tail/brake light LED
Too many electrical accessories
Burnt-out tail/brake light LED
Tail/brake light LED burnt out
Wrong tail/brake light LED
Faulty battery
Incorrectly adjusted rear brake light switch
Tail/brake light LED life expired
Turn signal does not come on
Faulty turn signal switch
Damaged or faulty wire harness
Faulty battery
Turn signal flashes slowly
Faulty main switch
Faulty turn signal switch
Incorrect turn signal bulb
Turn signal remains lit
Turn signal flashes quickly
Incorrect turn signal bulb
8-4
XV19SV(C)/XV19V(C)/XV19MV(C)/XV19CTSV(C)/XV19CTV(C)/XV19CTMV(C) 2006 WIRING DIAGRAM
15
A
11
12
13
16
WIRE HARNESS SUB-WIRE-HARNESS1
17
(BLUE)
18
28
32
29
32
(BLUE)
C
14
C
C
32
31
32
30
19
24
(BLACK)
(GRAY)
(BLACK)
D
D
D
D
33
20
E
E
E
27
DD
(BLACK)
ON
OFF
(GRAY)
(BLACK)
(BLACK)
21
(GRAY)
(BLACK)
34
22
10
(BLACK)
(BLACK)
25
(BLACK)
35
(BLACK)
B
(GRAY)
B
26
B
B
36
(BLACK)
(DARK GRAY)
B
23
81
37
(BLACK)
80
79
38
78
76
50
(BLACK)
49
48
51
77
47
39
40
75
65
74
52
54
(BLACK)
67
68
69
70
(BLUE)
(BLUE)
PUSH
55
53
56
(BLACK)
57
(BLACK)
41
42
43
44
45
46
PUSH
(L)
N
(R)
(BLACK)
(BLACK)
(BLACK)
(BLACK)
66
(BLACK)
71
(GRAY)
(GRAY)
(GRAY)
(GRAY)
(GRAY)
(GRAY)
72
62
73
A
A
63
(BLACK)
(BLACK)
64
61
60
59
(GRAY)
58
(GRAY)
(BLACK) (BLACK)
(BLACK)
EAS28740
WIRING DIAGRAM
XV19SV(C)/XV19V(C)/
XV19MV(C)/XV19CTSV(C)/
XV19CTV(C)/XV19CTMV(C)
2006
1. AC magneto
3. Main switch
4. Main fuse
5. Backup fuse (odometer and
clock)
6. Battery
8. Starter relay
9. Starter motor
10. Diode 1
11. Relay unit
12. Starting circuit cut-off relay
13. Fuel pump relay
14. Neutral switch
15. Diode 2
17. Fuel pump
18. Fuel sender (fuel pump)
21. Cylinder-#1 intake air pressure
sensor
22. Cylinder-#2 intake air pressure
sensor
24. Speed sensor
32. Spark plug
35. Injector #1
36. Injector #2
37. O2 sensor
38. Meter assembly
39. Neutral indicator light
40. Multi-function meter
41. Engine trouble warning light
42. Fuel level warning light
43. Meter light
44. Left turn signal indicator light
45. Right turn signal indicator light
46. High beam indicator light
47. Fuel sender (fuel tank)
48. Horn 1
49. Horn 2
51. Headlight relay
52. Left handlebar switch

53. Clutch switch
54. Dimmer switch
55. Turn signal switch
56. Horn switch
57. Select switch
58. Front right turn signal/position
light
59. Front left turn signal/position
light
60. Rear right turn signal light
61. Rear left turn signal light
63. Headlight (high beam)
64. Headlight (low beam)
65. Right handlebar switch
66. Front brake light switch
68. Start switch
69. Accessory light switch
70. Reset switch
71. Accessory light (OPTION)
72. Tail/brake light
73. License plate light
75. Auxiliary DC coupler
76. Auxiliary DC connector fuse
77. Ignition fuse
78. Headlight fuse
79. Signaling system fuse
80. Taillight fuse
81. ECU fuse
EAS28750
COLOR CODE
B
Br
Ch
Dg
G
Gy
L
O
P
R
Sb
W
Y
B/Br
B/G
B/L
B/R
B/Y
Br/L
Br/W
G/B
G/L
G/R
G/W
G/Y
Gy/G
Gy/R
Gy/W
L/B
L/G
L/R
L/W
L/Y
P/L
P/W
P/Y
R/B
R/G
R/L
R/W
R/Y
Sb/W
W/B
W/G
W/R
W/Y
Y/B
Y/G
Y/L
Y/R
Black
Brown
Chocolate
Dark green
Green
Gray
Blue
Orange
Pink
Red
Sky blue
White
Yellow
Black/Brown
Black/Green
Black/Blue
Black/Red
Black/Yellow
Brown/Blue
Brown/White
Green/Black
Green/Blue
Green/Red
Green/White
Green/Yellow
Gray/Green
Gray/Red
Gray/White
Blue/Black
Blue/Green
Blue/Red
Blue/White
Blue/Yellow
Pink/Blue
Pink/White
Pink/Yellow
Red/Black
Red/Green
Red/Blue
Red/White
Red/Yellow
Sky blue/White
White/Black
White/Green
White/Red
White/Yellow
Yellow/Black
Yellow/Green
Yellow/Blue
Yellow/Red

XV1900 RoadlinerStratoliner06 09 REPAIR MANUAL

Uploaded by

Copyright:

Available Formats

XV1900 RoadlinerStratoliner06 09 REPAIR MANUAL

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

XV1900 RoadlinerStratoliner06 09 REPAIR MANUAL

Uploaded by

Copyright:

Available Formats

What is the purpose of the service manual?

What is the purpose of the service manual?

How should a mechanic use the service manual?

How should a mechanic use the service manual?

Fix it like a Pro

How to use this Service Manual

Supplementary Service Manual (if available)

HOW TO USE THIS MANUAL

The following symbols are not relevant to every

1. Serviceable with engine mounted

PERIODIC CHECKS AND ADJUSTMENTS

VEHICLE IDENTIFICATION NUMBER

OUTLINE OF THE FI SYSTEM

15. Lean angle sensor

1. Air temperature sensor

13. Intake air pressure sensor

Be sure to stop the vehicle before making

The multi-function meter unit is equipped with

The speedometer shows the riding speed.

Be sure to turn the key to ON before using the

Do not operate the engine in the tachometer

The fuel gauge indicates the amount of fuel in

Do not allow the fuel tank to empty itself completely.

To set the clock:

Odometer, tripmeter, and clock modes

1. Multi-function meter unit panel

4. Adjust the multi-function meter unit panel

Brightness control mode

Multi-function meter unit panel

The brightness can be adjusted for the following:

6. Push the SELECT switch to select the

7. Push the SELECT switch.

PREPARATION FOR REMOVAL AND

GASKETS, OIL SEALS AND O-RINGS

2. Use only the proper tools and cleaning equipment.

LOCK WASHERS/PLATES AND COTTER

4. During disassembly, clean all of the parts and

BEARINGS AND OIL SEALS

Do not spin the bearing with compressed air

CHECKING THE CONNECTIONS

CHECKING THE CONNECTIONS

If there is no continuity, clean the terminals.

If the pin 1 on the terminal is flattened, bend it

Make sure all connections are tight.

Tappet adjusting tool (4 mm)

Oil filter wrench

Belt tension gauge

Steering nut wrench

Damper rod holder

Fork seal driver

Pivot shaft wrench

Valve spring compressor

Valve guide remover (6)

Valve guide installer (6)

Valve guide reamer (6)

Piston pin puller set

Universal clutch holder

Yamaha bond No. 1215

Vacuum/pressure pump gauge set

Fuel pressure adapter