Electronic Transistor Ignition For Cars Kit Manual PDF

ELECTRONIC TRANSISTOR IGNITION FOR CARS
K2543
nnin
other ru
o
m
s
d
ting an
tter star d 6V systems.
e
b
a
r
a
V an
our c
Gives y Suitbale for 12
H2543IP1
g.
Features & Specifications

Even the most sceptical one has tot admit that the electronic ignition system has a great advantage over the conventional
ignition system. Car constructors now mount such a new system on their most expensive models.
THE ADVANTAGES ARE :
Better ignition
Less air pollution
Gasoline economy
Better running engine, especially at very high and very low speed
Visible less wear of the breaking points, which means a constant calibrated state.
Specifications :
Completely shockproof
Practically test on 2-4-6-8 cylinder engines during a total amount of 2.500.000 km.
Principle: transistorized ignition
Connection element: Darlington transistor, triple diffused
Connection current: 4 A
Connection speed : Up to 500 KHz
Typical firing period : 2.000 second
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.
Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thin raisin-core solder. Do not use any flux or grease.
A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
Needle nose pliers, for bending leads, or to hold components in place.
Small blade and Phillips screwdrivers. A basic range is fine.
0.0
00
For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.
Follow the instructions carefully. Read and understand the entire step before you perform each operation.
Perform the assembly in the correct order as stated in this manual
Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
Values on the circuit diagram are subject to changes.
Values in this assembly guide are correct*
Use the check-boxes to mark your progress.
Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet.
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
AXIAL COMPONENTS ARE TAPED IN THE CORRECT

MOUNTING SEQUENCE !
REMOVE THEM FROM THE TAPE ONE AT A TIME !
Construction
1. Resistors
2. Diodes. Watch the polarity !
R...
CHOOSE
6 or 12V
:
:
:
:
:
:
:
330
330
150
100
150
150
150
(3 - 3 - 1 - B) (1W)
(3 - 3 - 1 - B) (1W)
(1 - 5 - 1 - B)
(1 - 0 - 1 - B)
(1 - 5 - 1 - B) (1W)
(1 - 5 - 1 - B) (1W)
(1 - 5 - 1 - B) (1W)
:
:
:
:
:
:
:
150
150
68
100
68
68
68
1N4007
1N4007
1N4007
1N4007
CATHODE
D...
20mm M3 bolt
Insulated washer
ZD1 : 150V0
ZD2 : 150V0
Heatsink
Mica insulation
CATHODE
Z D ...
4. Electrolytic Capacitor.
Plastic spacer
C1 : 0,22F/630VDC
6V battery
R1
R2
R3
R4
R5
R6
R7
:
:
:
:
3. Zenerdiodes. Watch the

polarity !
12V battery
R1
R2
R3
R4
R5
R6
R7
D1
D2
D3
D4
6. Transistor T2 + heatsink
(1 - 5 - 0 - B) (1W)
(1 - 5 - 0 - B) (1W)
(6 - 8 - 0 - B)
(1 - 0 - 1 - B)
(6 - 8 - 0 - B) (1W)
(6 - 8 - 0 - B) (1W)
(6 - 8 - 0 - B) (1W)
Transistor, metallic side
M3 serrated lock washer

M3 nut
5. Transistor T1
T1 : 2N2219A
T2 : TIP162 or BU931P
5
Installing in the car
7. Installing in the car

First of all, control the breaker points for a correct setting as per the constructors instructions, or better,
use a new set of points, before installing the ignition system.

The existing ignition condenser is to be disconnected. This is very important.
This condenser may be inside or outside the distributor.

ex.: On a 2 cylinders Citron, this condenser is fitted to the breakers, thus unscrew the nut and remove out of the car.
Supple leads of minimum 1mm square are to be used to make the connections, this to increase the func-
tion security. All connections and contacts are to be checked and must be good. A bad soldering or a bad
contact may conduct to some headaches.
BATTERY +
These four leads (connections 1, 2, 3 and 4)
Coil
may already be soldered to the PCB of the

ignition system, make them long enough so
they could be cut later at the
desired length.
breakers
Seek for an adequate to mount the ignition
system. Do not place the system under the

canopy without being boxed or insulated,
because the oxidation and other
atmospheric circumstances may shorten the
life of the transistorized ignition system.
condenser
4
3
4
2
3
1
1
K2543
DISCONNECT
CHASSIS -
WIRING : min 1mm
Installing in the car

There are different possibilities to dodge this problem :
(1) Install your system under the dashboard
(2) Spray a non-conductive protective varnisch (available in every retail shop) on the whole system, of which
a "Thick" layer must be applied on the components and the circuit side. Once this layer is dried, a second
layer may be sprayed. The ignition system may be fixed under the engine canopy.
(3) Build the system into a box well closed, but the heatsink has to be well ventilated. Don't use a
plastic bag or another similar material as fixed around the PCB.
(4) Insulate the entire ignition system with resin (also available in retail shops) but do not insulate the heatsink
which has to be ventilated.
The heatsink must be contact free from the frame (earth) of your car. The two holes of the heatsink are
used as fixing holes. Utilize small screws or Parker-screws. Ensure that the PCB has no contact with the
metal part of your vehicle.
Disconnect the lead going from the coil to the breakers points, and disconnect also the condenser.
Follow the instructions on the figure for all connections. Connection 1 of the PCB goes to the + 6/12V
coming from the ignition key. This "+ 6/12V" is also at the PLUS of the coil. If a ballast resistor is used,
the connection must be made in front of this resistor.
Connection 2 of the PCB goes to the breakers (do not forget to disconnect the condenser on one side).
Connection 3 goes to the connection of the coil, which was previously connected to the breakers.
And now connection 4 goes to the frame (earth) of the car, thus to the MINUS of the battery.
Test & maintenance
8. Test
The installation is now finished. Verify as follows :
The condenser is disconnected (very important)
All connections are well fixed
No lead is misconnected or mixed with another.
Now the engine may Start.
9. Maintenance
The ignition system on itself does not require a maintenance. The ignition system maintains the breaker
points in a good condition, so they will not be burned, as the bring only a few amount of current to the electric
system.
So, a pair of new breakers may stay for 50.000 km on the car without a maintenance, which means there is
no more need to verify every 5.000 or 10.000 km for the contact angle and ignition time.
Just clean the points sometimes, with a cloth dipped in acetone, to remove the oil. By buying a pair of new
points, you will see they are covered with a protective resin, acting as an insulator. Remove this resin with
sandpaper or with a degreasing solvent. After 50.000 km it will wise to change your breaker points because
wear of the notch and also for mechanical fatigue.
The sparkplugs also are to be checked as, with bad plugs, the best ignition system will not work. Verify the
plugs or buy new plugs. Do not forget that by trying to save on your plugs you will pay for gasoline, whatever
ignition system you use. If the electrodes are burned too far, the arcing between the gap of the electrodes will
go to the piston, with result into a burned piston.
8
PCB
PCB
R1
R2
R5
R6
R7
ZD1
ZD2
D3
D4
T1
D2
D1
R3
T2
R4
C1
VELLEMAN
Diagram
DIAGRAM
1
R1
R2
330/1W 330/1W
R5
150
1W
R6
150
1W
R7
150
1W
ZD1
ZD2
3
150V 150V
2
R3
150
D1
D3
D2
T1
1N4007 1N4007
R4
100
2N2219A
T2
1N4007
D4
1N4007
TIP162
C1
.22F
10
VELLEMAN NV
Legen Heirweg 33, B-9890 GAVERE
Belgium (Europe)
Modifications and typographical errors reserved

Velleman nv. H2543IP - 2014 - ED1 (rev.2)
5 410329 409272

Electronic Transistor Ignition For Cars Kit Manual PDF

Uploaded by

Copyright:

Available Formats

Electronic Transistor Ignition For Cars Kit Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electronic Transistor Ignition For Cars Kit Manual PDF

Uploaded by

Copyright:

Available Formats

ELECTRONIC TRANSISTOR IGNITION FOR CARS

Features & Specifications

A good quality soldering iron (25-40W) with a small tip.

Thin raisin-core solder. Do not use any flux or grease.

Needle nose pliers, for bending leads, or to hold components in place.

Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

AXIAL COMPONENTS ARE TAPED IN THE CORRECT

2. Diodes. Watch the polarity !

3. Zenerdiodes. Watch the

Transistor, metallic side

M3 serrated lock washer

Installing in the car

7. Installing in the car

use a new set of points, before installing the ignition system.

This condenser may be inside or outside the distributor.

These four leads (connections 1, 2, 3 and 4)

may already be soldered to the PCB of the

Seek for an adequate to mount the ignition

system. Do not place the system under the

WIRING : min 1mm

Installing in the car

Test & maintenance

Now the engine may Start.

Modifications and typographical errors reserved

You might also like