Kia 6282 K

SEMICONDUCTOR
KIA6282K
TECHNICAL DATA
BIPOLAR LINEAR INTEGRATED CIRCUIT
4.6W DUAL AUDIO POWER AMPLIFIER
A
F
S
KIA6282K is an audio power IC with built-in two channels

developed for portable radio cassette tape recorder with power
ON/OFF switch. Because of the parts reduction and SIP
(Single Inline Package), space merit is remarkable.
Thermal shut down protection circuit is built in.
DETAIL "A"
FEATURES
High Power.
D1
POUT=2.5W/CH (Typ.)
: (VCC=9V, RL=4 , f=1kHz, THD=10%)
POUT=4.6W/CH
: (VCC=12V, RL=4 , f=1kHz, THD=10%)
D2
Low popping noise at power ON.

Small Quiescent Current.
L2
L1
H1
H2
DETAIL "A"
T
DIM
A
B
D1
D2
d
F
G
H1
H2
L1
L2
P
Q
R
S
T
MILLIMETERS
_ 0.2
29.7 +
_ 0.2
4.0 +
_ 0.1
0.6 +
_ 0.1
0.7 +
_
0.5+ 0.1
_ 0.2
28.0 +
_ 0.2
0.5 +
_
8.5 + 0.3
_ 0.3
15.0 +
_ 0.2
2.5 +
_ 0.2
5.5+
2.54
R1.6
0.4
_ 0.2
22.0 +
0.4+0.1/-0.05
: ICCQ=19mA (Typ.) (VCC=9V, VIN=0)

Soft Clip.
SSIP-12
Built-in thermal shut down protection circuit.

Best for supply voltage 9V, 12V.
Operation supply voltage range : VCC=6~15V.
MAXIMUM RATING (Ta=25

CHARACTERISTIC
)
SYMBOL
RATING
UNIT
VCC
20
IO(peak)
2.5
Power Dissipation
PD
12.5
Operating Temperature
Topr
-20 75
Storage Temperature
Tstg
-55 150
Supply Voltage
Output Current (Peak/CH)
1994. 10. 31
Revision No : 0
1/8
KIA6282K
ELECTRICAL CHARACTERISTICS
(Unless otherwise specified, VCC=9V, f=1kHz, Rg=600
CHARACTERISTIC
SYMBOL
Quiescent Current
, RL=4
, Ta=25
TEST
TEST CONDITION
CIRCUIT
MIN.
TYP.
MAX.
UNIT
19
45
mA
2.0
2.5
ICCQ
VIN=0
POUT (1)
THD=10%
POUT (2)
THD=10%, Vcc=12V
4.6
THD
POUT=1W/CH
0.25
1.0
GV (1)
Rf=82
43
45
47
Output Power
Total Harmonic Distortion
, VOUT=0dBm
Voltage Gain
dB
GV (2)
Input Resistance
RIN
Output Noise voltage
VNO
Ripple Rejection Ratio
R.R
Cross Talk
C.T
V6,V7
Input Offset Voltage
Rf=0, VOUT=0dBm
Rg=10k
, BW=20Hz
20kHz
Rg=600
, VRIP=0.2Vrms
fRIP=100Hz
Rg=600 , Amp 1 2
VOUT=0dBm, f=1kHz
-
56
30
0.3
1.0
mVrms
54
dB
45
dB
20
60
mV
TYPICAL DC VOLTAGE OF EACH TERMINAL (VCC=9V, Ta=25 )
TERMINAL NO.
10
11
12
DC VOLTAGE (V)
8.2
4.5
VCC
8.9
0.6
0.01
0.01
0.6
GND
4.5
8.2
VCC
pin is connected to VCC.
1994. 10. 31
Revision No : 0
2/8
KIA6282K
BLOCK DIAGRAM/TEST CIRCUIT
2200uF
C10
VCC 1
12
VCC
VCC 2
C6
Ripple
C3
220uF
Rf2
IN2
NF2
8
82
C9
ch-2
-
30
47uF
11
20k
9
OUT-2
10
B.S.2
C7 100uF
IN-2
BIAS CIRCUIT
THERMAL SHUT DOWN
PROTECTION CIRCUIT
C5
* C IN
OUT-1
1000uF
20K
47uF
C1
30
82
C2
ch-1
C8
RL
NF1
5
1000uF
RL
R f1
IN1
0.15uF
0.15uF
IN-1
C4
* C IN
100uF
B.S.1
1
GND
* This IC can be used without coupling capacitor ( C IN ) . If volume slide noise

occured by input offset voltage is undesirable, it needs to use the capacitor ( C IN ) .
1994. 10. 31
Revision No : 0
3/8
KIA6282K
APPLICATION INFORMATION AND APPLICATION METHOD
1. ADJUSTMENT OF VOLTAGE GAIN
The voltage gain Gv is obtained as follows by R1, R2 and Rf in Fig. 1.
Rf+R1+R2
Rf+R1
6 /7
Gv=56dB(Typ.)
When Rf=82
, Gv=45dB(Typ.)
By increasing Rf, reduction of Gv is Possible.
INPUT
5 /8
47uF
When Rf=0,
Rf
CNF
GV = 20 log
R1
30
+
AMP
R2
2/
10
OUTPUT
20k
However, since the feedback increase is liable to

produce oscillation, it is recommended to use this
Fig 1.
at 40dB or over.
2. THERMAL SHUT-DOWN CIRCUIT

The thermal shut-down circuit is built in for the purpose of preventing the destruction
of IC due to the abnormal temperature rise when the heat radiation is insufficient.
The operation temperature is set at radiation Fin temperature 175 (Typ.)
At this temperature or over the bias is interrupted to prevent the destruction of IC.
3. INPUT STAGE
The input circuit of this IC is as shown in Fig. 2.
PNP TR:Q1 is provided in the input circuit so as
OUTPUT
to make its usage possible without the input coupling

capacitor. However, at pins
and
20k
Q2
, max 60mV
Q3
offset voltage is produced. Application after checking
to DRIVER
volume slide noise is recommended.
INPUT
6/
7
Q1
30k
CIN
30
For cutting the volume slide noise, insert the input

capacitor : CIN in series to interrupt the DC component.
2/
10
to BIAS
NF
5/
47uF
Rf
GND
Fig. 2
1994. 10. 31
Revision No : 0
4/8
KIA6282K
4. OSCILLATION PREVENTIVE MEASURES
For oscillation preventive capacitor C6 and C7 between the output terminal and GND, it is recommended to use Polyester
film capacitor having good characteristics for temperature and for high frequency. Since the characteristics of the capacitor is
liable to be influenced the temperature, use this capacitor after the temperature test to check the oscillation allowance.
In addition, as the position of the electrolytic capacitor has a remarkable influence on the oscillation, connect C10 to VCC at the
nearest possible position from power GND. At using this application with the voltage gain reduced, oscillation is liable to be produced.
Apply the capacitor after checking enough for its capacity, type and mounting position.
* As the oscillation
allowance varies according to the printed pattern layout, the standard printed board of KEC is recommended
to be referred to for design it.
5. POWER ON/OFF SWITCH

There is power ON/OFF switch at
in not same
pin. However, output power is changed by
pin supply voltage, after referring to attached date, select
pin supply voltage when
pin supply voltage
pin supply voltage.
6. INPUT VOLTAGE
When the excessive signal is input, turning-up is produced in the clip waveform.
The turning-up point is VIN=300mVrms(Typ.) : VCC=9V, RL=4 , f=1kHz : Enough care must be taken for this phenomenon.
7. GND LINE
GND pin is not separated for Pre-GND and for Pw-GND. That is liable to cause distortion and cross talk worse.
Before use this IC, please check it.
1994. 10. 31
Revision No : 0
5/8
KIA6282K
OUT2
OUT1
C8
C9
GND
C7
C6
C5
C4
VCC
1
Rf1
Rf2
C10
12
POWER
ON/OFF
CIN
CIN
C2
C1
C3
GND
KIA6282K
IN2
1994. 10. 31
Revision No : 0
GND
IN1
6/8
KIA6282K
P D - P OUT
P D - POUT
5
5
4
POWER DISSIPATION PD (W)
f=1k
3
VCC =9V
2
1
VCC =6V
f=1kHz
R L=4
2
1
R.R - f
R.R - R g
VRIP =0.2Vrms
Rg =600
-40
-60
10
30
VRIP =0.2Vrms
-40
-60
-80
0.03
100
FREQUENCY f (kHz)
f=1kHz
THD=10%
4
L=
L =3
L =2
0
8
12
16
SUPPLY VOLTAGE VCC (V)
Revision No : 0
20
TOTAL HARMONIC DISTORTION THD (%)
0.3
10
30
100
SIGNAL SOURCE RESISTANCE R g (k)
POUT - VCC
0.1
THD - POUT
30
f=1kHz
R L=4
10
5
3
1
-20
VC =1
C 2V
0.3
VCC =9V
R L=4
f RIP =100Hz
VCC =9
0.1
-20
OUTPUT POWER POUT (W)
VCC =9V
R L=4
0.03
OUTPUT POWER P OUT (W)
R L=3
RIPPLE REJECTION RATIO R.R (dB)
RIPPLE REJECTION RATIO R.R (dB)
1994. 10. 31
VCC =9V
-80
R L=2
VCC =6
POWER DISSIPATION PD (W)
R L=4
VCC =12V
0.5
0.3
0.1
0.03
0.1
0.3
10
7/8
5
3
1
R L=3
RL=4
0.1
0.1
0.03
0.3
10
5
3
1
0.5
0.3
0.1
0.03
R L=4
5
3
f=10kHz
1
f=1kHz
f=100Hz
0.1
0.1
0.03
0.3
10
1 INFINITE HEAT SINK

2 80cm 2 x2mm
Al HEAT SINK
3 18cm 2 x2mm
Al HEAT SINK
4 NO HEAT SINK
6
3
4
4
0
20
40
60
80
100
120
140
AMBIENT TEMPERATURE Ta ( C)
1994. 10. 31
10
5
3
7V
8V
9V
1
0.5
0.3
0.1
0.03
0.3
0.1
PD MAX - VCC
10
VCC1=9V
R L=4
f=1kHz
VCC :
SUPPLY
VOLTAGE
at 3 Pin
PD - Ta
12
Revision No : 0
10
THD - POUT
30
14
VCC =9V
MAXIMUM POWER DISSIPATION

PD MAX (W)

ALLOWABLE POWER DISSIPATION
THD - P OUT
30
0.5
0.3
10
0.3
0.1
6V
R L=2
0.3
f=1kHz
10
VCC2 =5V
0.5
VCC =12V
10
30
L=
VCC =9V
f=1kHz
30
THD - P OUT
R
R L =2
L=
3
THD - P OUT
KIA6282K
160
12
10
f=1kHz
10
THD=10%
=2
=3
RL
R L 4
=
RL
6
4
2
0
0
10
12
14
16
SUPPLY VOLTAGE VCC (V)
8/8

Kia 6282 K

Uploaded by

Copyright:

Available Formats

Kia 6282 K

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kia 6282 K

Uploaded by

Copyright:

Available Formats

SEMICONDUCTOR

BIPOLAR LINEAR INTEGRATED CIRCUIT

4.6W DUAL AUDIO POWER AMPLIFIER

KIA6282K is an audio power IC with built-in two channels

Low popping noise at power ON.

: ICCQ=19mA (Typ.) (VCC=9V, VIN=0)

Built-in thermal shut down protection circuit.

MAXIMUM RATING (Ta=25

Total Harmonic Distortion

Output Noise voltage

Ripple Rejection Ratio

Input Offset Voltage

TYPICAL DC VOLTAGE OF EACH TERMINAL (VCC=9V, Ta=25 )

pin is connected to VCC.

BLOCK DIAGRAM/TEST CIRCUIT

* This IC can be used without coupling capacitor ( C IN ) . If volume slide noise

By increasing Rf, reduction of Gv is Possible.

However, since the feedback increase is liable to

2. THERMAL SHUT-DOWN CIRCUIT

to make its usage possible without the input coupling

offset voltage is produced. Application after checking

volume slide noise is recommended.

For cutting the volume slide noise, insert the input

to be referred to for design it.

5. POWER ON/OFF SWITCH

pin. However, output power is changed by

pin supply voltage, after referring to attached date, select

pin supply voltage when

pin supply voltage

pin supply voltage.

POWER DISSIPATION PD (W)

SUPPLY VOLTAGE VCC (V)

TOTAL HARMONIC DISTORTION THD (%)

SIGNAL SOURCE RESISTANCE R g (k)

OUTPUT POWER POUT (W)

OUTPUT POWER P OUT (W)

OUTPUT POWER POUT (W)

RIPPLE REJECTION RATIO R.R (dB)

RIPPLE REJECTION RATIO R.R (dB)

POWER DISSIPATION PD (W)

OUTPUT POWER POUT (W)

1 INFINITE HEAT SINK

OUTPUT POWER POUT (W)

OUTPUT POWER P OUT (W)

TOTAL HARMONIC DISTORTION THD (%)

MAXIMUM POWER DISSIPATION

TOTAL HARMONIC DISTORTION THD (%)

OUTPUT POWER POUT (W)

OUTPUT POWER P OUT (W)

TOTAL HARMONIC DISTORTION THD (%)

TOTAL HARMONIC DISTORTION THD (%)

SUPPLY VOLTAGE VCC (V)

You might also like