TDS - Mastertop 1210 Plus

MASTERTOP
1210 PLUS
Multi component solvent free epoxy floor
coating system
Description
MASTERTOP 1210 PLUS is a multi component solvent free
epoxy floor coating system designed to offer continuous
seamless floor protection at thicknesses between 0.5mm1.5mm. MASTERTOP 1210 PLUS may be applied to
produce either a smooth or profiled finish.
Primary uses
MASTERTOP 1210 PLUS has good wear and abrasion
resistance and is suitable for use in many industrial
applications. It can be used as a surface coating where a
hygienic and high gloss appearance is required.
It provides impermeable protection against common oils,
greases, lubricants, aviation fuels or oils such as Skydrol. In
addition it offers good general chemical resistance, but as in
all corrosive situations, a full analysis of operating and
exposure conditions is required, followed by reference to
chemical resistance data to ensure product suitability.
Packaging
MASTERTOP 1210 PLUS is supplied as a 26kg multi
component pack (including colour pack).
Typical data of hardened

material*
Pot life
Curing time
Mixed density at 25C
Mixed density with Solvent No. 2
Maximum service temp
Compressive strength (ASTM C57993)
1 day
3 days
14 days
Flexural Strength (BS 6319 Part 3)
Tensile Strength (BS 6319 Part 7)
Slip resistance (TRRL rubber)
25C
40 mins.
15 hours
1.556
40C
22 mins.
10 hours
60C
36.4
69.6
79.4
19.0N/mm
15.0N/mm
104
48.6
70.6
80.2
Guide to application
MASTERTOP 1210 PLUS may be applied in the following
industries
NB This gives examples only and does not constitute a full
and comprehensive list. For further information on
application possibilities contact Degussa M.E.
Pharmaceutical and other medical laboratory situations.

Industrial production facilities
Light engineering workshops
Aircraft hangars and maintenance areas.
Warehouses
Utility rooms and corridors
Vehicle movement areas
Advantages
Good wear and abrasion resistance.

Easily applied.
Smooth high gloss finish for hygienic applications.
Good general chemical resistance.
Limited maintenance.
Durable
Remove all surface laitance, oil, grease or any defective

concrete that will reduce the bond of the MASTERTOP 1210
PLUS to the substrate.
The surface over which the MASTERTOP 1210 PLUS is to
be laid must be flat and suitably prepared.
Surface irregularities must be ground down or filled out with
CONCRESIVE 2200 or repair materials from the EMACO
range.
A light etch giving the texture of medium grit sand paper is
the ideal surface profile for the application of MASTERTOP
1210 PLUS, this can be achieved by light grit blasting,
capture blasting or surface grinding.
After all preparation has been completed, ensure dust is
removed from the surface preferably by vacuuming.
Prior to application MASTERTOP 1210 PLUS should be
stored under cover in an air-conditioned environment and
protected from extremes of temperature which may cause
inconsistent workability, finish and cure times for the mixed
material.
Sealing:
All porous concrete surfaces to be overlaid with
MASTERTOP 1210 PLUS must be sealed with a coat of
MASTERTOP 1200 PLUS resin with the addition of 0.5ltr of
SOLVENT NO. 2. Add the SOLVENT NO. 2 to the base
and reactor components, after they have been decanted into
the mixing container, then mix the base and reactor
components together until all striations have disappeared.
Apply the mixed material to the dry substrate at the rate of
6-8 m / ltr using a medium or short hair roller. Allow the
sealer to become completely tack free before over-coating
with MASTERTOP 1210 PLUS.
Mixing:
Pour the reactor into the base container, add the colour
pack and mix using a drill and spiral mixing head until all
striations have disappeared and a uniform colour is obtained
(for a minimum of 1 minute). Add the MASTERTOP 1210
PLUS aggregate, whilst continuing to mix for a further 2
minutes or until it can be seen that the mixed material is
lump free.
Application:
To achieve a smooth finish at 0.5mm apply the
MASTERTOP 1210 PLUS, as a single coat with a notched
trowel or similar. At thickness greater than 0.5mm, use pin
screed, trowel or airless spray.
The coating should be rolled with a spike roller as soon as
possible after application to achieve a uniform finish. The
applied coating should be rolled a second time after 15-20
minutes. Continuous rolling does not harm the product while
it is still fluid.
Equipment care
Remove uncured MASTERTOP 1210 PLUS from tools and
equipment using SOLVENT NO 2.
Storage
Store out of direct sunlight, clear of the ground on pallets
protected from rainfall. Avoid excessive compaction and
protect from extremes of temperatures. In tropical climates
the product must be stored in an air conditioned
environment.
Safety precautions
As with all chemical products, care should be taken during
use and storage to avoid contact with eyes, mouth, skin and
foodstuffs (which can also be tainted with vapour until
products is fully cured or dried). Treat splashes to eyes and
skin immediately. If accidentally ingested, seek medical
attention. Reseal containers after use.
Note
Field service, where provided, does not constitute
supervisory responsibility. For additional information contact
your local Degussa representative.
Always wear spiked shoes when rolling the MASTERTOP

1210 PLUS with a spiked roller.
Degussa reserves the right to have the true cause of any

difficulty determined by accepted test methods.
Yield
Quality and care
A 26kg unit will yield 16.71 litre of mixed material.
All products originating from Degussas Dubai, UAE facility

are manufactured under a management system
independently certified to conform to the requirements of the
quality, environmental and occupational health & safety
standards ISO 9001, ISO 14001 and OHSAS 18001.
MASTERTOP 1210 PLUS systems are supplied in

preweighed packs which should not be split or divided.
It is important to use complete packs.
08/2000 Degussa-UAE revised 11/2004
* Properties listed are only for guidance and are not a guarantee of
performance.
Degussa Construction Chemicals UAE LLC

P.O. Box 37127, Dubai, UAE
Tel: +971 4 8851000
Fax: +971 4 8851002
www.degussa-cc.ae
e-mail: marketingcc.mideast@degussa.com
Whilst any information contained herein is true, accurate and

represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or
distributors, as the conditions of use and the competence of any labour
involved in the application are beyond our control.
Certificate No.
963680
As all Degussa technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
Certificate No.
945787
Certificate No.
772556

TDS - Mastertop 1210 Plus

Uploaded by

Copyright:

Available Formats

TDS - Mastertop 1210 Plus

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS - Mastertop 1210 Plus

Uploaded by

Copyright:

Available Formats

MASTERTOP

Typical data of hardened

Pharmaceutical and other medical laboratory situations.

Good wear and abrasion resistance.

Remove all surface laitance, oil, grease or any defective

Always wear spiked shoes when rolling the MASTERTOP

Degussa reserves the right to have the true cause of any

Quality and care

A 26kg unit will yield 16.71 litre of mixed material.

All products originating from Degussas Dubai, UAE facility

MASTERTOP 1210 PLUS systems are supplied in

08/2000 Degussa-UAE revised 11/2004

Degussa Construction Chemicals UAE LLC

Fax: +971 4 8851002

Whilst any information contained herein is true, accurate and

You might also like