Chockfast Red Tds PDF

CHOCKFAST Red
A Deep-Pour Epoxy Grout

Technical Bulletin #
617S
Product Description
CHOCKFAST Red is a three-component, high strength, 100% solids, epoxy grouting compound used to
grout large machinery and to support soleplates in all types of foundations. CHOCKFAST Red has an
extremely high compressive strength. This along with negligible shrinkage makes it ideal for installing
critically aligned machinery within very close tolerances.
Use & Benefits

CHOCKFAST Red has the following advantages when compared to conventional cement grouts:
Impervious to oil
Cures at least three times as quickly
No mixing ratios to measure
Grouts machinery in final aligned position
High physical strength
High impact strength
Resistance to many more chemicals
Strong bond to metal and concrete
Unaffected by weathering and freeze / thaw cycling
Stated physical properties assured
Superior resistance to fatigue
Design Considerations
CHOCKFAST Red is quick curing, relative to cement grouts, but the cure is thermally gentle. This allows
thick pours to be made without causing the stress cracks often associated with a hot-curing epoxy grout.
CHOCKFAST Red may be used in thickness greater than 2 inches (50mm), however, individual pours
should generally not exceed 18 inches (46cm) in thickness and 7 feet (2.2m) in length. When grouting
critically aligned machinery coupled to another machine, it is advisable to limit the final leveling pour in
accordance with the instructions in Bulletin No. 615 (latest revision).
CHOCKFAST Red contains no diluents that could interfere with the curing mechanism or that could
cause material loss during or after cure. Therefore, machinery may be positioned at its final elevation
before pouring because the shrinkage is negligible. Critical alignments are maintained during machinery
operation due to its high dimensional stability and resistance to creep and vibration.
Application Instructions
CHOCKFAST Red may be mixed with contractor's hoe and wheelbarrow or in a small portable mortar
mixer. Pre-condition resin, hardener and aggregate to 65-80F (18-27C) for 48 hrs. before mixing.
Thoroughly mix hardener with resin using a Jiffy Mixing Blade for 3 to 5 minutes then add resin/hardener
mix to aggregate. Where a very flowable mix is required the aggregate content may be reduced
accordingly. However, in load-bearing areas a maximum reduction to 3-1/2 bags is recommended.
Please contact the CHOCKFAST Distributor or ITW Philadelphia Resins if less than 3-1/2 bags are being
considered. See Bulletin No. 642 for mixing and installation procedures.
ITW POLYMER TECHNOLOGIES

130 Commerce Drive Montgomeryville, PA 18936 215-855-8450 Fax 215-855-4688
CHOCKFAST Red
Bulletin No. 617S, Page 2
Physical Properties
COMPRESSIVE STRENGTH
COMPRESSIVE MODULUS OF ELASTICITY
LINEAR SHRINKAGE
COEFFICIENT OF LINEAR THERMAL
EXPANSION
FLEXURAL STRENGTH
FLEXURAL MODULUS OF ELASTICITY
TENSILE STRENGTH
IZOD IMPACT STRENGTH
SERVICE TEMPERATURE
FIRE RESISTANCE
SPECIFIC GRAVITY
15,250 psi (1,072 kg/cm )

2,000,000 psi
2
(140,600 kg/cm )
ASTM C-579 MOD

ASTM C-579 MOD
Not Measurable
ASTM D-2566
-6 o
11.2 x 10 / F @ 32 F to 140 F
-6 o
o
o
(20.1 x 10 / C @ 0 C to 60 C)
2
ASTM D-696
4,025 psi (283 kg/cm )

2,000,000 psi
2
(140,600 kg/cm )
2
1,890 psi (133 kg/cm )
4.6 in.lb/in.
(0.02 N.m/mm)
o
o
Up to 140 F (60 C)
ASTM C-580
ASTM C-580
Self-Extinguishing
ASTM D-635
ASTM D-638
ASTM D-256
2.06
Product Information
UNIT COVERAGE
APPLICATION TEMPERATURE
UNIT PACKAGING
UNIT WEIGHT
SHIPPING WEIGHT
CURE TIME (approximate)
POT LIFE
SHELF LIFE
CLEAN UP
Date
1.6 ft or 2,765 in (45.3 Liters)

o
o
o
o
55 F (13 C) to 95 F (35 C)
Resin (NH): 1.6 gal (6.1 L) in a 3 gal pail
Hardener (NH): 0.9 gal (3.5 L) in a plastic tray
inserted into the top of the resin can
Aggregate: (4) 46 lb. (21 kg) bags
Resin: 15.4 lbs (7 kg)
Hardener: 7.6 lbs (3.4 kg)
Aggregate: 184 lbs (84 kg)
207 lbs (94 kg)
o
54 hours @ 60 F (16 C)
o
o
36 hours @ 72 F (21 C)
o
o
24 hours @ 80 F (27 C)
o
o
18 hours @ 90 F (32 C)
o
o
Approximately 3 hours @ 70 F (21 C)
2 years in dry storage
Water or IMPAX IXT-59 or similar epoxy solvent
02/2012
General: Every reasonable effort is made to insure the technical

information and recommendations on these data pages are true and
accurate to the best of our knowledge at the date of issuance.
However, this information is subject to change without notice. Prior
versions of this publication are invalid with the release of this version.
Products and information are intended for use by qualified applicators
that have the required background, technical knowledge, and
equipment to perform said tasks in a satisfactory manner. Consult
your local distributor for product availability, additional product
information, and technical support.
Warranty: ITW Philadelphia Resins, a division of Illinois Tool Works
Inc., warrants that its products meet their printed specifications. This
is the sole warranty. This warranty expires one year after product
shipment.
Warranty Claims: If any product fails to meet the above, ITW
Philadelphia Resins will, at its option, either replace the product or
refund the purchase price. ITW Philadelphia Resins will have no other
liability for breach of warranty, negligence, or otherwise. All warranty
claims must be made in writing within one year of the date of shipment.
No other claims will be considered.
Disclaimer: ITW Philadelphia Resins makes no other warranty,
expressed or implied, and specifically disclaims any warranty of
merchantability or fitness for a particular purpose.
Suggestions concerning the use of products are not warranties.

The purchaser assumes the responsibility for determining
suitability of products and appropriate use. ITW Philadelphia
Resins sole liability, for breach of warranty, negligence or
otherwise, shall be the replacement of product or refund of the
purchase price, at ITW Philadelphia Resins election. Under no
circumstances shall ITW Philadelphia Resins be liable for any
indirect, incidental or consequential damages.
Modification of Warranty: No distributor or sales representative
has the authority to change the above provisions. No change in
the above provisions will be valid unless in writing and signed by an
officer or the Technical Director of ITW Philadelphia Resins. No
term of any purchase order shall serve to modify any provision of
this document.
Mediation and Arbitration: If any dispute arises relating to
products or product warranties, either the purchaser or ITW
Philadelphia Resins may a) initiate mediation under the then
current Center for Public Resources (CPR) Model Procedure for
Mediation of Business Disputes, or b) initiate a non-binding
arbitration under the rules of the American Arbitration
Association for the resolution of commercial disputes.

Chockfast Red Tds PDF

Uploaded by

Copyright:

Available Formats

Chockfast Red Tds PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chockfast Red Tds PDF

Uploaded by

Copyright:

Available Formats

CHOCKFAST Red

A Deep-Pour Epoxy Grout

Use & Benefits

ITW POLYMER TECHNOLOGIES

15,250 psi (1,072 kg/cm )

ASTM C-579 MOD

4,025 psi (283 kg/cm )

1.6 ft or 2,765 in (45.3 Liters)

General: Every reasonable effort is made to insure the technical

Suggestions concerning the use of products are not warranties.

You might also like