Woodworking Tools and Methods NAVEDTRA 14043

CHAPTER 3
WOODWORKING TOOLS, MATERIALS, AND

METHODS
relate to the particular power tool under discussion.
You must keep in mind and continually stress to your
crew that woodworking power tools can be
woodworking craftsman, you must be able to use and
maintain a large variety of field and shop tools
dangerous, and that safety is everyones responsibility.
eff ectively. To perform your work quickly,
accurately, and safely, you must select and use the
correct tool for the job at hand. Without the proper SHOP TOOLS
tools and the knowledge to use them, you waste time,
reduce efficiency, and may injure yourself or others.
As a Builder, you might be assigned to a shop.
Therefore, you will need to know some of the
Power tools not only are essential in performing
common power tools and equipment found there.
specific jobs, but also play an important role in your
daily work activities. Keep in mind that you are
Shop Radial Arm Saw
responsible for knowing and observing all safety
precautions applicable to the tools and equipment you
Figure 3-1 illustrates a typical shop radial arm
operate. For additional information on the topics
discussed in this chapter, you are encouraged to study saw. The procedures used in the operation,
maintenance, and lubrication of any shop radial arm
Tools and Their Uses, NAVEDTRA 10085-B2.
saw
are found in the manufacturers operator and
Because that publication contains a detailed
maintenance
manuals. The safety precautions to be
discussion of common tools used by Builders, we will
observed for this saw are found in these same
not repeat that information in this chapter.
manuals. The primary difference between this saw
In this chapter, several of the most common
and other saws of this type (field saws) is the location
power tools used by Builders are briefly described. of controls.
Their uses, general characteristics, attachments, and
safety and operating features are outlined. To become
Tilt-Arbor Table Bench Saw
skilled with these power tools and hand tools, you
must use them. You should also study the
A tilt-arbor table bench saw (figure 3-2) is so
manufacturers operator and maintenance guides for
named because the saw blade can be tilted for cutting
each tool you use for additional guidance. We will
bevels by tilting the arbor. The arbor, located beneath
also be covering materials and methods of
the table, is controlled by the tilt handwheel. In
woodworking.
earlier types of bench saws, the saw blade remained
stationary and the table was tilted. A canted (tilted)
saw table is hazardous in many ways; most modern
POWER TOOLS
table saws are of the tilt-arbor type.
LEARNING OBJECTIVE: Upon completing
To rip stock, remove the cutoff gauges and set the
this section, you should be able to determine
rip fence away from the saw by a distance equal to the
the proper use and maintenance requirements
desired width of the piece to be ripped off. The piece
of portable power tools.
is placed with one edge against the fence and fed
Your duties as a Builder include developing and through with the fence as a guide.
improving your skills and techniques when working
To cut stock square, set the cutoff gauge at 90 to
with different power tools. In this section, well
identify and discuss the most common power tools the line of the saw and set the ripping fence to the
outside edge of the table, away from the stock to be
that are in the Builders workshop or used on the
jobsite. Well also discuss safety precautions as they cut. The piece is then placed with one edge against
As a Builder, hand and power woodworking tools
are essential parts of your trade. To be a proficient
3-1
Figure 3-1.A shop radial arm saw.
the cutoff gauge, held firmly, and fed through by

pushing the gauge along its slot.
The procedure for cutting stock at an angle
other than 90 (called miter cutting) is similar,
except that the cutoff gauge is set to bring the
piece to the desired angle with the line of the saw.
For ordinary ripping or cutting, the saw blade
should extend above the table top 1/8 to 1/4 inch
plus the thickness of the piece to be sawed. The
vertical position of the saw is controlled by the
depth of cut handwheel, shown in figure 3-2. The
angle of the saw blade is controlled by the tilt
handwheel. Except when its removal is absolutely
unavoidable, the guard must be kept in place.
The slot in the table through which the
saw blade extends is called the throat. The throat
is contained in a small, removable section of the
table called the throat plate. The throat plate is
removed when it is necessary to insert a wrench to
remove the saw blade.
29.136
Figure 3-2.Tilt-arbor bench saw.
3-2
The blade is held on the arbor by the arbor nut. A saw

is usually equipped with several throat plates,
containing throats of various widths. A wider throat is
required when a dado head is used on the saw. A dado
head consists of two outside grooving saws (which
are much like combination saws) and as many
intermediate chisel-type cutters (called chippers) as
are required to make up the designated width of the
groove or dado. Grooving saws are usually I/S-inch
thick; consequently, one grooving saw will cut a
1/8-inch groove, and the two, used together, will cut a
1/4-inch groove. Intermediate cutters come in
various thicknesses.
Observe the following safety precautions when
operating the tilt-arbor table bench saw:
Do not use a ripsaw blade for crosscutting or a
crosscut saw blade for ripping. When ripping
and crosscutting frequently, you should install
a combination blade to eliminate constantly
changing the blade. Make sure the saw blade is
sharp, unbroken, and free from cracks before
using. The blade should be changed if it
becomes dull, cracked, chipped, or warped.
Be sure the saw blade is set at proper height
above the table to cut through the wood.
The band saw has two large wheels on which a

continuous narrow saw blade, or band, turns, just as a
belt is turned on pulleys. The lower wheel, located
below the working table, is connected to the motor
directly or by means of pulleys or gears and serves as
the driver pulley. The upper wheel is the driven
pulley.
The saw blade is guided and kept in line by two
sets of blade guides, one fixed set below the table and
one set above with a vertical sliding adjustment. The
alignment of the blade is adjusted by a mechanism on
the backside of the upper wheel. Tensioning of the
bladetightening and loosening-is provided by
another adjustment located just back of the upper
wheel.
Cutoff gauges and ripping fences are sometimes
provided for use with band saws, but youll do most
of your work freehand with the table clear. With this
type of saw, it is difficult to make accurate cuts when
gauges or fences are used.
The size of a band saw is designated by the
diameter of the wheels. Common sizes are 14-, 16-,
18-, 20-, 30-, 36-, 42-, and 48-inch-diameter wheel
machines. The 14-inch size is the smallest practical
band saw. With the exception of capacity, all band
Avoid the hazard of being hit by materials

caused by kickbacks by standing to one side of
the saw.
Always use a push stick to push short, narrow
pieces between the saw blade and the gauge.
Keep stock and scraps from accumulating on
the saw table and in the immediate working
area.
Never reach over the saw to obtain material
from the other side.
When cutting, do not feed wood into the saw
blade faster than it will cut freely and cleanly.
Never leave the saw unattended with the power
on.
Band Saw
Although the band saw (figure 3-3) is designed
primarily for making curved cuts, it can also be used
for straight cutting. Unlike the circular saw, the band
saw is frequently used for freehand cutting.
3-3
Figure 3-3.Band saw.
saws are much the same with regard to maintenance,

operation, and adjustment.
A band saw should not be operated in a

location where the temperature is below 45F.
The blade may break from the coldness.
A rule of thumb used by many Seabees is that the

width of the blade should be one-eighth the minimum
radius to be cut. Therefore, if the piece on hand has a
4-inch radius, the operator should select a 1/2-inch
blade. Dont construe this to mean that the minimum
radius that can be cut is eight times the width of the
blade; rather, the ratio indicates the practical limit for
high-speed band saw work.
Using a small saw blade for large work or

forcing a wide saw on a small radius is bad
practice. The saw blade should, in all cases, be
as wide as the nature of the work will permit.
Blades, or bands, for band saws are designated by

points (tooth points per inch), thickness (gauge), and
width. The required length of a blade is found by
adding the circumference of one wheel to twice the
distance between the wheel centers. Length can vary
within a limit of twice the tension adjustment range.
Band saw teeth are shaped like the teeth in a hand
ripsaw blade, which means that their fronts are filed at
90 to the line of the saw. Reconditioning procedures
are the same as those for a hand ripsaw, except that
very narrow band saws with very small teeth must
usually be set and sharpened by special machines.
operating a band saw:
Band saws should not be stopped by thrusting a

piece of wood against the cutting edge or side
of the band saw blade immediately after the
power has been shut off; doing so may cause
the blade to break. Band saws with
36-inch-wheel diameters and larger should
have a hand or foot brake.
Particular care should be taken when
sharpening or brazing a band saw blade to
ensure the blade is not overheated and the
brazed joints are thoroughly united and
finished to the same thickness as the rest of the
blade. It is recommended that all band saw
blades be butt welded where possible; this
method is much superior to the old style of
brazing.
Drill Press
Keep your fingers away from the moving

blade.
Figure 3-4 shows a drill press. (The numbers in

Keep the table clear of stock and scraps so your
the figure correspond to those in the following text.)
work will not catch as you push it along.
The drill press is an electrically operated power
machine that was originally designed as a
Keep the upper guide just above the work, not
metal-working tool; as such, its use would be limited
excessively high.
in the average woodworking shop. However,
Dont use cracked blades. If a blade develops accessories, such as a router bit or shaper heads, jigs,
a click as it passes through the work, the
and special techniques, now make it a versatile
operator should shut off the power because the woodworking tool as well.
click is a danger signal that the blade is cracked
The motor (10) is mounted to a bracket at the rear
and may be ready to break. After the saw blade
of
the
head assembly (1) and designed to permit
has stopped moving, it should be replaced with
V-belt
changing for desired spindle speed without
one in proper condition.
removing the motor from its mounting bracket. Four
If the saw blade breaks, the operator should spindle speeds are obtained by locating the V-belt on
shut off the power immediately and not attempt any one of the four steps of the spindle-driven and
to remove any part of the saw blade until the motor-driven pulleys. The belt tensioning rod (16)
machine is completely stopped.
keeps proper tension on the belt so it doesnt slip.
If the work binds or pinches on the blade, the
operator should never attempt to back the work
away from the blade while the saw is in motion
since this may break the blade. The operator
should always see that the blade is working
freely through the cut.
3-4
The controls of all drill presses are similar. The

terms right and left are relative to the operators
position standing in front of and facing the drill press.
Forward applies to movement toward the operator.
Rearward applies to movement away from the
operator.
The on/off switch (11) is located in the front of

the drill press for easy access.
most cases, the quill lock handle will be in the

released position.
The spindle and quill feed handles (2) radiate

from the spindle and quill pinion feed (3) hub, which
is located on the lower right-front side of the head
assembly (1). Pulling forward and down on any one
of the three spindle and quill feed handles, which
point upward at the time, moves the spindle and quill
assembly downward. Release the feed handle (2) and
the spindle and quill assembly return to the retracted
or upper position by spring action.
The quill lock handle (4) is located at the lower
left-front side of the head assembly. Turn the quill
lock handle clockwise to lock the quill at a desired
operating position. Release the quill by turning the
quill lock handle counterclockwise. However, in
The head lock handle (5) is located at the left-rear

side of the head assembly. Turn the head leek handle
clockwise to lock the head assembly at a desired
vertical height on the bench column. Turn the head
lock handle counterclockwise to release the head
assembly. When operating the drill press, you must
ensure that the head lock handle is tight at all times.
The head support collar handle (6) is located at
the right side of the head support collar and below the
head assembly. The handle locks the head support
collar, which secures the head vertically on the bench
column, and prevents the head from dropping when
the head lock handle is released. Turn the head
support collar lock handle clockwise to lock the
support to the bench column and counterclockwise to
Figure 3-4.Drill press.
3-5
release the support. When operating the drill press,

ensure that the head support collar lock handle is tight
at all times.
Woodworking Lathe
The adjustable locknut (14) is located on the

depth gauge rod (17). The purpose of the adjustable
locknut is to regulate depth drilling. Turn the
adjustable locknut clockwise to decrease the
downward travel of the spindle. The locknut must be
secured against the depth pointer (13) when operating
the drill press. The depth of the hole is shown on the
depth scale (15).
The lathe is used in turning or shaping round

drums, disks, and any object that requires a true
diameter. The size of a lathe is determined by the
maximum diameter of the work it can swing over its
bed. There are various sizes and types of wood lathes,
ranging from very small sizes for delicate work to
large surface or bull lathes that can swing jobs 15 feet
in diameter.

operating a drill press:
Figure 3-5 illustrates a type of lathe that you may

find in your shop. It is made in three sizes to swing
16-, 20-, and 24-inch diameter stock. The lathe has
four major parts: bed, headstock, tailstock, and tool
rest.
The woodworking lathe is, without question, the

oldest of all woodworking machines. In its early
As you face the drill press, the tilting table lock
form, it consisted of two holding centers with the
handle is located at the right-rear side of the tilting
suspended stock being rotated by an endless rope belt.
table bracket. The lockpin secures the table at a
It was operated by having one person pull on the rope
horizontal or 45 angle. This allows you to move the
hand over hand while the cutting was done by a
table to the side, out of the way for long pieces of
second person holding crude hand lathe tools on an
wood. The table support collar (8) allows you to raise
improvised beam rest.
or lower the table. Turn the tilting table lock handle
counterclockwise to release the tilting table bracket so
The actual operations of woodturning performed
it can be moved up and down or around the bench
on a modern lathe are still done to a great degree with
column. Lock the tilting table assembly at the desired
woodturners hand tools. However, machine lathe
height by turning the lock handle clockwise. When
work is coming more and more into use with the
operating the drill press, ensure that the tilting table
introduction of newly designed lathes for that
lock handle is tight at all times.
purpose.
Make sure that the drill is properly secured in

the chuck (12) and that the chuck key (9) is
removed before starting the drill press.
The lathe shown in figure 3-5 has an iron bed and

comes in assorted lengths. The bed is a broad, flat
surface that supports the other parts of the machine.
Make sure your material is properly secured.

Operate the feed handle with a slow, steady
pressure to make sure you dont break the drill
bit or cause the V-belt to slip.
Make sure all locking handles are tight and that
the V-belt is not slipping.
Make sure the electric cord is securely
connected and in good shape.
Make sure you are not wearing hanging or
loose clothing.
The headstock is mounted on the left end of the

lathe bed. All power for the lathe is transmitted
through the headstock. It has a fully enclosed motor
that gives variable spindle speed. The spindle is
threaded at the front end to receive the faceplates. A
faceplate attachment to the motor spindle is furnished
to hold or mount small jobs having large diameters.
There is also a flange on the rear end of the spindle to
receive large faceplates, which are held securely by
four stud bolts.
The tailstock is located on the right end of the
lathe and is movable along the length of the bed. It
supports one end of the work while the other end is
being turned by the headstock spur. The tail center
can be removed from the stock by simply backing the
screw. The shank is tapered to center the point
automatically.
Listen for any sounds that may be signs of

trouble.
After you have finished operating the drill
press, make sure the area is clean.
3-6
Figure 3-5.A woodworking lathe with accessories.

Most large sizes of lathes are provided with a
power-feeding carriage. A cone-pulley belt
arrangement provides power from the motor, and
trackways are cast to the inside of the bed for sliding
the carriage back and forth. All machines have a
metal bar that can be attached to the bed of the lathe
between the operator and the work. This serves as a
hand tool rest and provides support for the operator
in guiding tools along the work. It may be of any size

and is adjustable to any desired position.
In lathe work, wood is rotated against the special
cutting tools (illustrated in figure 3-6). These tools
include turning gouges (view A); skew chisels (view
B); parting tools (view C); round-nose (view D);
square-nose (view E); and spear-point (view F)
Figure 3-6.Lathe cutting tools.

3-7
chisels. Other cutting tools are toothing irons and

auxiliary aids, such as calipers, dividers, and
templates.
Turning gouges are used chiefly to rough out
nearly all shapes in spindle turning. The gouge sizes
vary from 1/8 to 2 or more inches, with 1/4-, 3/4-, and
1-inch sizes being most common.
The tool rest must be used when milling stock.

Adjust and set the compound or tool rest for the
start of the cut before turning the switch on.
Take very light cuts, especially when using
hand tools.
Never attempt touse calipers on interrupted

surfaces while the work is in motion.
Skew chisels are used for smoothing cuts to finish
a surface, turning beads, trimming ends or shoulders,
and for making V-cuts. They are made in sizes from Jointer
1/8 to 2 1/2 inches in width and in right-handed and
The jointer is a machine for power planing stock
left-handed pairs.
on faces, edges, and ends. The planing is done by a
Parting tools are used to cut recesses or grooves revolving butterhead equipped with two or more
with straight sides and a flat bottom, and also to cut knives, as shown in figure 3-8. Tightening the set
off finished work from the faceplate. These tools are screws forces the throat piece against the knife for
available in sizes ranging from 1/8 to 3/4 inch.
holding the knife in position. Loosening the set
Scraping tools of various shapes are used for the screws releases the knife for removal. The size of a
jointer is designated by the width, in inches, of the
most accurate turning work, especially for most
faceplate turning. A few of the more common] y usedbutterhead; sizes range from 4 to 36 inches. A 6-inch
jointer is shown in figure 3-9.
shapes are illustrated in views D, E, and F of
figure 3-6. The chisels shown in views B, E, and F
are actually old jointer blades that have been ground
to the required shape; the wood handles for these
homemade chisels are not shown in the illustration.
The principle on which the jointer functions is

illustrated in figure 3-10. The table consists of two
parts on either side of the butterhead. The stock is
started on the infeed table and fed past the butterhead
onto
the outfeed table. The surface of the outfeed
A toothing iron (figure 3-7) is basically a
square-nose turning chisel with a series of parallel table must be exactly level with the highest point
grooves cut into the top surface of the iron. These reached by the knife edges. The surface of the infeed
turning tools we used for rough turning of segment table is depressed below the surface of the outfeed
work mounted on the face plate. The points of the
toothing iron created by the parallel grooves serve as
a series of spear point chisels (detail A); therefore, the
tool is not likely to catch and dig into the work like a
square-nose turning chisel. The toothing iron is made
with course, medium, and fine parallel grooves and
varies from 1/2 to 2 inches in width.
Lathe turning can be extremely dangerous. You
therefore must use particular care in this work.
Observe the following safety precautions:
When starting the lathe motor, stand to one
side. This helps you avoid the hazard of flying
debris in the event of defective material.
Figure 3-7.Toothing iron lathe tool.
Figure 3-8.Four-knife butterhead for a jointer.
3-8
held against the fence. A piece is surfaced by

feeding it through flat with one of the edges
against the fence. However, this operation should,
if possible, be limited to straightening the face of
the stock. The fence can be set at 90 to produce
squared faces and edges, or at any desired angle to
produce beveled edges or ends.
Only sharp and evenly balanced knives
should be used in a jointer cutting head. The
knives must not be set to take too heavy a cut
because a kickback is almost certain to result,
especially if there is a knot or change of grain in
the stock. The knives must be securely refastened
after the machine has been standing in a cold
building over the weekend.
29.138
Figure 3-9.Six-inch jointer.
table an amount equal to the desired depth of cut.
The usual depth of cut is about 1/16 to 1/8 inch.
The level of the outfeed table must be
frequently checked to ensure the surface is exactly
even with the highest point reached by the knife
edges. If the outfeed table is too high, the cut will
become progressively more shallow as the piece is
fed through. If the outfeed table is too low, the
piece will drop downward as its end leaves the
infeed table, and the cut for the last inch or so will
be too deep.
To set the outfeed table to the correct height,
first feed a piece of waste stock past the
cutterhead until a few inches of it lie on the
outfeed table. Then, stop the machine and look
under the outfeed end of the piece. If the outfeed
table is too low, there will be a space between the
surface of the table and the lower face of the piece.
Raise the outfeed table until this space is
eliminated. If no space appears, lower the outfeed
table until a space does appear. Now, run the
stock back through the machine. If there is still a
space, raise the table just enough to eliminate it.
Note that the cutterhead cuts toward the
infeed table; therefore, to cut with the grain, you
must place the piece with the grain running
toward the infeed table. A piece is edged by
feeding it through on edge with one of the faces
Each hand-fed jointer should be equipped

with a cylindrical cutting head, the throat of
which should not exceed 7/1 6 inch in depth or 5/8
inch in width. It is strongly recommended that no
cylinder be used in which the throat exceeds 3/8
inch in depth or 1/2 inch in width.
Each hand-fed jointer should have an automatic
guard that covers all the sections of the head on
the working side of the fence or gauge. The guard
should automatically adjust horizontally for edge
jointing and vertically for surface work, and it
should remain in contact with the material at all
times.
When operating the jointer, observe the
following safety precautions:
Always plane with the grain. A piece of

wood planed against the grain on a jointer
may be kicked back.
Never place your hands directly over the

inner cutterhead. Should the piece of wood
kick
Figure 3-10.Operating principle of a

jointer.
3-9
back, your hands will drop on the blades. Start

with your hands on the infeed bed. When the piece
of wood is halfway through, reach around with
your left hand and steady the piece of wood on the
outfeed bed. Finish with both your hands on the
outfeed bed.
Never feed a piece of wood with your thumb

or finger against the end of the piece of
wood being fed into the jointer. Keep your
hands on top of the wood at all times.
Avoid jointing short pieces of wood

whenever possible. Joint a longer piece of
wood and then cut it to the desired size. If
you must joint a piece of wood shorter than
18 inches, use a push stick to feed it through
the jointer.
Never use a jointer with dull cutter blades.

Dull blades have a tendency to kick the
piece, and a kickback is always dangerous.
Keep the jointer table and the floor around

the jointer clear of scraps, chips, and
shavings. Always stop the jointer before
brushing off and cleaning up those scraps,
chips, and shavings.
Never joint a piece of wood that contains

loose knots.
Keep your eyes and undivided attention on

the jointer as you are working. Do not talk
to anyone while operating the jointer.
Remember, the jointer is one of the most
dangerous machines in the woodworking shop.
Only experienced and responsible personnel
should be allowed to operate it using the basic
safety precautions provided above.
Surfacer
A single surfacer (also called a single planer) is
shown in figure 3-11. This machine surfaces stock
on one face (the upper face) only. (Double
surfacers, which surface both faces at the same
time, are used only in large planing mills.)
The single surfacer cuts with a cutterhead like
the one on the jointer, but, on the single surfacer,
the cutterhead is located above instead of below
the drive rollers. The part adjacent to the
cutterhead is pressed down against the feed bed by
the chip breakers (just ahead of the cutterhead)
and the pressure bar (just behind the cutterhead).
The pressure bar temporarily
29.135
Figure 3-11.Single surfacer.
3-10
straightens out any warp a piece may have; a piece

that goes into the surfacer warped will come out still
warped. This is not a defect in the machine; the
surfacer is designed for surfacing only, not for truing
warped stock. If true plane surfaces are desired, one
face of the stock (the face that goes down in the
surfacer) must be trued on the jointer before the piece
is feed through the surfacer. If the face that goes
down in the surfacer is true, the surfacer will plane
the other face true.
operating a surfacer:
The cutting head should be covered by metal

guards.
Feed rolls should be guarded by a hood or a

semicylindrical guard.
Never force wood through the machine.

If a piece of wood gets stuck, turn off the
Shaper
The shaper is designed primarily for edging
curved stock and for cutting ornamental edges, as on
moldings. It can also be used for rabbeting, grooving,
fluting, and beading.
The flat cutter on a shaper is mounted on a
vertical spindle and held in place by a hexagonal
spindle nut. A grooved collar is placed below and
above the cutter to receive the edges of the knives.
Ball bearing collars are available for use as guides on
irregular work where the fence is not used. The part
of the edge that is to remain uncut runs against a ball
bearing collar underneath the cutter, as shown in the
bottom view of figure 3-12. A three-wing cutter (top
view of figure 3-12) fits over the spindle. Cutters
come with cutting edges in a great variety of shapes.
For shaping the side edges on a rectangular
piece, a light-duty shaper has an adjustable fence,
like the one shown on the shaper in figure 3-13. For
shaping the end edges on a rectangular piece, a
machine of this type has a sliding fence similar to the
cutoff gauge on a circular saw. The sliding fence
slides in the groove shown in the table top.
surfacer and lower the feed bed.
On larger machines, the fence consists of a

board straightedge, clamped to the table with a hand
screw,
68.27
Figure 3-13.Light-duty shaper with adjustable
fence.
Figure 3-12.Three-wing cutter for a shaper.

3-11
as shown in figure 3-14. A semicircular opening is

sawed in the edge of the straightedge to accommodate
the spindle and the cutters. Whenever possible, a
guard of the type shown in the figure should be placed
over the spindle.
For shaping curved edges, there are usually a
couple of holes in the table, one on either side of the
spindle, in which vertical starter pins can be inserted.
When a curved edge is being shaped, the piece is
guided by and steadied against the starter pin and the
ball bearing collar on the spindle.
When operating a shaper, observe the following
safety precautions:
Like the jointer and surfacer, the shaper cuts
toward the infeed side of the spindle, which is
against the rotation of the spindle. Therefore,
stock should be placed with the grain running
toward the infeed side.
Make sure the cutters are sharp and well
secured.
Never make extremely deep cuts.

Make sure the shaper cutters rotate toward the
work.
Whenever possible, always use a guard,
pressure bar, hold-down, or holding jig.
If possible, place the cutter on the shaper
spindle so that the cutting will be done on the
lower side of the stock.
Do not attempt to shape small pieces of wood.
Check all adjustments before turning on the
power.
SAFETY NOTE
The spindle shaper is one of the most
dangerous machines used in the shop. Use
extreme caution at all times.
If curved or irregularly shaped edges are to be

PORTABLE HAND TOOLS
shaped, place the stock in position and make
sure the collar will rub against the part of the
In addition to using power shop tools, you will be
edge, which should not be removed.
required to operate different types of portable hand
used,
tools in the field. You therefore need to understand
Whenever the straight fence cannot be
the safety precautions associated with these.
always use a starting pin in the table top.
Figure 3-14.Shaper table showing straightedge fence and guard.
3-12
Portable Electric Circular Saw

The portable electric circular saw is used chiefly
as a great labor-saving device in sawing wood
framing members on the job. The size of a circular
saw is determined by the diameter of the largest blade

it can use. The most commonly used circular saws are
the 7 1/4- and 8 1/4-inch saws. There are two
diff erent types of electric saws, as shown in
figure 3-15: the side-drive (view A) and the
Figure 3-15.-Side-drive (view A) and worm-drive (view B) circular saws
3-13
ABRASIVE BLADES. Abrasive blades are

worm-drive (view B). Circular saws can use many
used
for cutting metal, masonry, and plastics. These
different types of cutting blades, some of which are
blades are particularly useful for scoring bricks so
shown in figure 3-16.
they can be easily split.
COMBINATION CROSSCUT AND RIP
Figure 3-17 shows how versatile the circular saw
BLADES. Combination blades are all-purpose
can be. To make an accurate ripping cut (view A), the
blades for cutting thick and thin hardwoods and
softwoods, both with or across the grain. They can
also be used to cut plywood and hardboard.
CROSSCUT BLADES. Crosscut blades have
fine teeth that cut smoothly across the grain of both
hardwood and softwood. These blades can be used
for plywood, veneers, and hardboard.
RIP BLADES. Rip blades have bigger teeth
than combination blades, and should be used only to
cut with the grain. A rip fence or guide will help you
make an accurate cut with this type of blade.
HOLLOW-GROUND BLADES. Hollowground blades have no set. They make the smoothest
cuts on thick or thin stock. Wood cut with these
blades requires little or no sanding.
Figure 3-16.-Circular saw blades.
Figure 3-17.-Different ways to use a circular saw.
3-14
ripping guide is set a distance away from the saw

equal to the width of the strip to be ripped off. It is
then placed against the edge of the piece as a guide for
the saw. To make a bevel angle cut up to 45 (view
B), you just set the bevel adjustment knob to the angle
you want and cut down the line. To make a pocket cut
(views C and D), a square cut in the middle of a piece
of material, you retract the guard back and tilt the saw
so that it rests on the front of the base. Then, lowering
the rear of the saw into the material, hold it there until
it goes all the way through the wood. Then, follow
your line.
and covers the blade to the depth of the teeth

when you lift the saw off the work.
Wear goggles or face shields while using the
saw and while cleaning up debris afterward.
Grasp the saw with both hands and hold it
firmly against the work. Take care to prevent
the saw from breaking away from the work and
thereby causing injury.
Inspect the blade at frequent intervals and
always after it has locked, pinched, or burned
the work. Disconnect the saw from the power
source before performing this inspection.

operating a circular saw:
Inspect daily the electric cords that you use for

cuts or breaks. Before cutting boards, make
sure the cord is not in the way of the blade.
Dont force the saw through heavy cutting

stock. If you do, you may overload the motor
and damage it.
Before using the saw, carefully examine the
material to be cut and free it of nails or other
metal objects. Cutting into or through knots
should be avoided, if possible.
Disconnect the saw from its power source
before making any adjustments or repairs to
the saw. This includes changing the blade.
Make sure all circular saws are equipped with
guards that automatically y adjust themselves to
the work when in use so that none of the teeth
protrude above the work. Adjust the guard
over the blade so that it slides out of its recess
Saber Saw
The saber saw (figure 3-18) is a power-driven
jigsaw that cuts smooth and decorative curves in
wood and light metal. Most saber saws are light-duty
machines and not designed for extremely fast cutting.
There are several different, easily interchangeable
blades (figure 3-19) designed to operate in the saber
saw. Some blades are designed for cutting wood and
some for cutting metal.
The best way to learn how to handle this type of
tool is to use it. Before trying to do a finished job
with the saber saw, clamp down a piece of scrap
plywood and draw some curved as well as straight
lines to follow. You will develop your own way of
Figure 3-18.-Saber saw.
Figure 3-19.-Saber saw blades.
3-15
gripping the tool, which will be affected somewhat by

the particular tool you are using. On some tools, for
example, you will find guiding easier if you apply
some downward pressure on the tool as you move it
forward. If you dont use a firm grip, the tool will
tend to vibrate excessively and roughen the cut. Do
not force the cutting faster than the design of the blade
allows or you will break the blade.
You can make a pocket cut with a saber saw just
like you can with a circular saw, although you need to
drill a starter hole to begin work. A saber saw can also
make bevel-angle and curve cuts.
operating the saber saw:
Figure 3-20.-Reciprocating saw.
Before working with the saber saw, be sure to

Before operating this saw, be sure you are using a
remove your rings, watches, bracelets, and
blade that is right for the job. The manufacturers
instruction manual shows the proper saw blade to use
other jewelry.
for a particular material. The blade must be pushed
If you are wearing long sleeves, roll them up.
securely into the opening provided. Rock it slightly
to ensure a correct fit, then tighten the setscrew.
Be sure the saber saw is properly grounded.
To start a cut, place the saw blade near the
Use the proper saw blade for the work to be
material
to be cut. Then, start the motor and move the
done, and ensure the blade is securely locked in
blade
into
the material. Keep the cutting pressure
place.
constant, but do not overload the saw motor. Never
Be sure the material to be cut is free of any
reach underneath the material being cut.
obstructions.
Keep your full attention focused on the work operating a reciprocating saw:
being performed.
Disconnect the saw when changing blades or
Grip the handle of the saw firmly. Control the
making adjustments.
forward and turning movements with your free
hand on the front guide.
To start a cut, place the forward edge of the saw
base on the edge of the material being worked,
start the motor, and move the blade into the
material.
Portable Reciprocating Saw
The portable reciprocating saw (saw-all)
(figure 3-20) is a heavy-duty power tool that you can
use for a variety of woodworking maintenance work,
remodeling, and roughing-in jobs. You can use it to
cut rectangular openings, curved openings, along
straight or curved lines, and flush.
Blades for reciprocating saws are made in a great
variety of sizes and shapes. They vary in length from
2 1/2 to 12 inches and are made of high-speed steel or
carbon steel. They have cutting edges similar to those
3-16
Figure 3-21.-Portable router with edge guide.
guide slip into the two holes provided on the router

base. The edge guide can be adjusted to move in or
out along the two rods to obtain the desired lateral
depth cut.
Place the foot of the saw firmly on the stock

before starting to cut.
Dont cut curves shaper than the blade can
handle.
There are two classifications of router bits.

Built-in, shank-type bits fit into the chuck of the
router. Screw-type bits have a threaded hole through
the center of the cutting head, which allows the
cutting head to be screwed to the shank. Figure 3-22
shows a few of the most common router bits.
When cutting through a wall, make sure you

dont cut electrical wires.
Router
The router is a versatile portable power tool that

can be used free hand or with jigs and attachments.
Figure 3-21 shows a router typical of most models. It operating a router:
consists of a motor containing a chuck into which the
Before operating a router, be sure the work
router bits are attached. The motor slides into the
piece is well secured and free of obstruction.
base in a vertical position. By means of the depth
adjustment ring, easy regulation of the depth of a cut
Make sure the router is disconnected from the
is possible. Routers vary in size from 1/4 to 2 1/2
power source before making any adjustment or
horsepower, and the motor speed varies from 18,000
changing bits.
to 27,000 rpm.
One of the most practical accessories for the
router is the edge guide. It is used to guide the router
in a straight line along the edge of the board. The
edge guide is particularly useful for cutting grooves
on long pieces of lumber. The two rods on the edge
Dont overload the router when cutting the

material.
Use both hands to hold the router when cutting
material.
Figure 3-22.-Router bits.
3-17
If a smoothing cut is desired, make that cut first

and then recheck the dimensions. Make as many
The portable electric power plane (figure 3-23) is passes as necessary with the plane to reach the desired
widely used for trimming panels, doors, frames, and dimensions, checking frequently so as not to remove
so forth. It is a precision tool capable of exact depth too much material. The greater the depth of the cut,
of cut up to 3/16 inch on some of the heavier models.
the slower you must feed the tool into the work. Feed
However, the maximum safe depth of cut on any
pressure should be enough to keep the tool cutting,
model is 3/32 inch in any one pass.
The power plane is essentially a high-speed motor but not so much as to slow it down excessively. Keep
that drives a cutter bar, containing either straight or wood chips off the work because they can mar the
surface of the stock as the tool passes over them.
spiral blades, at high speed.
Operating the power plane is simply a matter of Keep your hands away from the butterhead or blades
setting the depth of cut and passing the plane over the when a cut is finished.
work. First, make careful measurements of the piece,
The L-shaped base, or fence, of the plane should
where it is to fit, and determine how much material
be pressed snugly against the work when planing,
has to be removed. Then, the stock being planed
assuring that the edge will be cut square. For bevel
should be held in a vise, clamped to the edge of a
cuts, loosen the setscrew on the base, set the base at
bench, or otherwise fi rmly held. Check the
the desired bevel, and then retighten the setscrew.
smoothness and straightness of all the edges.
Portable Power Plane
Figure 3-23.-Portable electric power plane.
3-18
Figure 3-24.-Heavyduty 1/2-inch portable drill (view A) and light-duty 1/2-inch portable drill (view B).
operating a portable power plane:

operating a portable drill:
Make sure that the plane is turned off before

plugging it in.
Make sure that the drill or bit is securely

mounted in the chuck.
Make sure you disconnect the plug before

making any adjustment.
Hold the drill firmly as prescribed by the

manufacturer of the drill.
When feeding the drill into the material, vary
the pressure you apply to accommodate the
different kinds of stock. Be careful not to bind
the drill or bit.
Dont attempt to power plane with one

handyou need two.
Always clamp your work securely in the best
position to perform the planing.
When finished planing, make sure you
disconnect the power cord.
When drilling a deep hole, withdraw the drill

several times to clean the drill bit.
Portable Sanders
Portable Power Drills
There are three types of portable sanders: belt,

disk, and finish sanders. When using a belt sander
Portable power drills have generally replaced
(figure 3-25), be careful not to gouge the wood. The
hand tools for drilling holes because they are faster size of a belt sander is usually identified by the width
and more accurate. With variable-speed controls andof its sanding belt. Belt widths on heavier duty
special clutch-drive chucks, they can also be used as
electric screwdrivers. More specialized power-driven
screwdrivers are also available; these have greatly
increased the efficiency of many fastening operations
in construction work.
The two basic designs for portable electric drills
(figure 3-24) are the spade design for heavy-duty
construction (view A) and the pistol-grip design for
lighter work (view B). Sizes of power drills are based
on the diameter of the largest drill shank that will fit
into the chuck of the drill.
The right-angle drill is a specialty drill used in
plumbing and electrical work. It allows you to drill
holes at a right angle to the drill body.
3-19
Figure 3-25.-Belt sander.
The finish sander (figure 3-27) is used for light and

fine sanding. Two kinds of finish sanders are available.
One operates with an orbital (circular) motion (view A),
and the other has an oscillating (back and forth)
movement (view B). Finish sanders use regular
abrasive paper (sandpaper) cut to size from full sheets.
Observe the following safety tips when operating
portable sanders:
Make sure the sander is off before plugging it in.
Make sure that you use two hands if using the
belt sander.
Figure 3-26.-Portable disk sander.

on the
models are usually 3 or 4 inches. Depending
make and model, belt lengths vary from 21to 27
inches. Different grades of-abrasives are available.
Dont press down on the sander. The weight of

the sander is enough to sand the material.
Make sure the sander is disconnected when
changing sandpaper.
The disk sander (figure 3-26) is a useful tool for

Keep the electrical cord away from the area
being sanded.
removing old finish, paint, and varnish from siding,
wood flooring, and concrete. For best results with a
disk sander, tip the machine lightly with just enough Power Nailers and Staplers
pressure to bend the disk. Use a long, sweeping
There is a wide variety of power nailers and
motion, back and forth, advancing along the surface.
When using a disk sander, always operate it with both staplers available. A typical example of each is
shown in figure 3-28. A heavy-duty nailer is used for
hands.
Figure 3-27.-Two types of finish sanders: orbital (view A)

and oscillating (view B).
3-20
Figure 3-28.-Heavyduty pneumatic nailer (view A) and

pneumatic stapler (view B).
framing or sheathing work; finish nailers are used for

paneling or trimming. There is also a wide variety of
staplers that you can use for jobs, such as fastening
sheeting, decking, or roofing. These tools are often
driven by compressed air. The amount of pneumatic,
or air, pressure required to operate the tool depends on
the size of the tool and the type of operation you are
performing. Check the manufacturers manual for the
proper air pressure to operate the tool.
The power nailer and power stapler are great
timesaving tools, but they are also very dangerous
tools. Observe the following safety precautions when
using them:
Use the correct air pressure for the particular
tool and job.
Use the right nailer or stapler for the job and
also the correct nails and staples.
Keep the nose of the tool pointed away from
your body.
When you are not using a nailer or stapler or if

you are loading one, disconnect the air
supply.
MATERIALS
this section, you should be able to identify the
types, sources, uses, and characteristics of
th e co mmo n w oo ds us ed o n v ar i o us
construction projects.
Of all the different construction materials, wood
is probably the most often used and perhaps the most
important. The variety of uses of wood is practically
unlimited. Few Seabee construction projects are
accomplished without using some type of wood. It is
used for permanent structures as well as concrete
forms, scaffolding, shoring, and bracing, which may
be used again and again. The types, sources, uses,
and characteristics of common woods are given in
table 3-1. The types of classifications of wood for a
large project are usual] y designated in the project
specifications and included in the project drawings.
Table 3-1.-Common Woods

TYPES
SOURCES
USES
CHARACTERISTICS
East of Rockies
Oars, boat thwarts, benches, Strong, heavy, hard, tough, elastic,

gratings, hammer handles, close straight grain, shrinks very
little, takes excellent finish, lasts well
cabinets, ball bats, wagon
construction, farm implements
BEECH
East of
Mississippi and
southeastern
Canada
C a b in et wo rk , i mi t at i o n
mahogany furniture, wood
dowels, capping, boat trim,
interior finish, tool handles,
turnery, shoe lasts, carving,
flooring
Similar to birch but not so durable

when exposed to weather, shrinks and
checks considerably, close grain,
light or dark red color
BIRCH
East of
Mississippi River
and north of gulf
coast states,
southeast
Canada, and
Newfoundland
Ca b i n etw or k, im it a t io n
mahogany furniture, wood
dowels, capping, boat trim,
interior finish, tool handles,
turnery, carving
Hard, durable, fine grain, even

texture, heavy, stiff, strong, tough,
takes high polish, works easily, forms
excellent base for white enamel
finish, but not durable when exposed.
Heartwood is light to dark reddish
brown in color
ASH
3-21
Table 3-1.-Common Woodscontinued

TYPES
BUTTERNUT
DOUGLAS FIR
SOURCES
Southern
Canada,
Minnesota,
eastern U.S. as
far south as
Alabama and
Florida
USES
CHARACTERISTICS
Toys, altars, woodenware, Very much like walnut in color but

millwork, interior trim, furni- softer, not so soft as white pine and
ture, boats, scientific instru-basswood, easy to work, coarse
grained, fairly strong
ments
Deck planking on large

ships, shores, strongbacks,
plugs,
filling pieces and
Pacific coast and
British Columbia bulkheads of small boats,
building construction, dimension timber, plywood
Excellent structural lumber, strong,

easy to work, clear straight grained,
soft but brittle. Heartwood is durable
in contact with ground, best structural
timber of northwest
States east of
Colorado
Agricultural implements, Slippery, heavy, hard, tough, durable,

wheel-stock, boats, furniture,difficult to split, not resistant to decay
crossties, posts, poles
Arkansas,
Tennessee, Ohio,
and Kentucky
Tools, handles, wagon stock,Very heavy, hard, stronger and

hoops, baskets, vehicles, tougher than other native woods, but
wagon spokes
checks, shrinks, difficult to work,
subject to decay and insect attack
MAPLE
All states east of

Colorado and
Southern Canada
Excellent furniture, high- Fine grained, grain often curly or

grade floors, tool handles, Birdss Eyes, heavy, tough, hard,
ship construction, crossties, strong, rather easy to work, but not
durable. Heartwood is light brown,
counter tops, bowling pins
sap wood is nearly white
LIVE OAK
Southern Atlantic
and gulf coasts
of U. S., Oregon,
and California
Implements, wagons, ship- Very heavy, hard, tough, strong,

durable, difficult to work, light brown
building
or yellow sap wood nearly white
MAHOGANY
Honduras,
Mexico, Central
America,
Florida, West
Indies, Central
Africa, and other
tropical sections
Furniture, boats, decks,

fixtures, interior trim in
expensive homes, musical
instruments
NORWAY PINE
States bordering
Great Lakes
Dimension timber, masts, Light, fairly hard, strong, not durable

in contact with ground
spars, piling, interior trim
ELM
HICKORY
3-22
Brown to red color, one of most

useful of cabinet woods, hard,
durable, does not split badly, open
grained, takes beautiful finish when
grain is filled but checks, swells,
shrinks, warps slightly
Table 3-1.-Common WoodsContinued

TYPES
PHILIPPINE
MAHOGANY
POPLAR
RED CEDAR
RED OAK
REDWOOD
SOURCES
Philippine Islands
Virginias,
Tennessee,
Kentucky, and
Mississippi
Valley
USES
CHARACTERISTICS
Pleasure boats, medium- Not a true mahogany, shrinks,

grade furniture, interior trim expands, splits, warps, but available
in long, wide, clear boards
Low-grade furniture, cheaply
constructed buildings, interior
finish, shelving drawers,
boxes
Soft, cheap, obtainable in wide

boards, warps, shrinks, rots easily,
light, brittle, weak, but works easily
and holds nails well, fine-textured
Mothproof chests, lining for Very light; soft, weak, brittle, low
East of Colorado linen closets, sills, and othershrinkage, great durability, fragrant
uses similar to white cedar
scent, generally knotty, beautiful
and north of
when finished in natural color, easily
Florida
worked
Virginias,
Tennessee,
Arkansas,
Kentucky, Ohio,
Missouri,
Maryland
California
Interior finish, furniture,

Tends to warp, coarse grain, does not
cabinets, millwork, crosstieslast well when exposed to weather,
when preserved
porous, easily impregnated with
preservative, heavy, tough, strong
General construction, tanks,Inferior to yellow pine and fir in

paneling
strength, shrinks and splits little,
extremely soft, light, straight grained,
very durable, exceptional y resistant
to decay
New York, New

England, West
Virginia, central
Canada, Great
Lakes states,
Idaho,
Washington,
Oregon
Railway ties, resonance wood,Light, soft, low strength, fair durpiles, airplanes, oars, masts,ability, close grain, yellowish, sap
spars, baskets
wood indistinct
SUGAR PINE
California and
Oregon
Same as white pine
TEAK
India, Burma,
Thailand, and
Java
Deck planking, shaft logs forLight brown color, strong, easily

small boats
worked, durable, resistant to moisture
damage
SPRUCE
3-23
Very light, soft, resembles white pine
Table 3-1.-Common WoodsContinued

TYPES
SOURCES
WALNUT
Eastern half of
U.S. except
southern Atlantic
and gulf coasts,
some in New
Mexico, Arizona,
California
USES
CHARACTERISTICS
Expensive furniture, cabinets, Fine cabinet wood, coarse grained

interior woodwork, gun but takes beautiful finish when pores
stocks, tool handles, airplane closed with wood filler, medium
propellers, fine boats, musical weight, hard, strong, easily worked,
instruments
dark chocolate color, does not warp
or check brittle
Eastern coast of
U. S., and around
Great Lakes
Boat planking, railroad ties, Soft, lightweight, close grained,

shingles, siding, posts, poles exceptionally durable when exposed
to water, not strong enough for
building construction, brittle, low
shrinkage, fragment, generally knotty
WHITE OAK
The Virginias,
Tennessee,
Arkansas,
Kentucky, Ohio,
Missouri,
Maryland, and
Indiana
Boat and ship stems, stern- Heavy, hard, strong, medium coarse
posts, knees, sheer strakes, grain, tough, dense, most durable of
fenders, capping, transoms,hardwoods, elastic, rather easy to
shaft logs, framing for build-work, but shrinks and likely to check.
ings, strong furniture, tool Light brownish grey in color with
handles, crossties, agricultural reddish tinge, medullary rays are
implements, fence posts
large and outstanding and present
beautiful figures when quarter sawed,
receives high polish
WHITE PINE
Minnesota,
Wisconsin,
Maine,
Michigan, Idaho,
Montana,
Washington,
Oregon, and
California
WHITE CEDAR
YELLOW PINE
Virginia to Texas
Patterns, any interior job or Easy to work, fine grain, free of

exterior job that doesnt knots, takes excellent finish, durable
require maximum strength, when exposed to water, expands
window sash, interior trim, when wet, shrinks when dry, soft,
millwork, cabinets, cornices white, nails without splitting, not
very strong, straight grained
Most important lumber for Hard, strong, heartwood is durable in

heavy construction and the ground, grain varies, heavy,
exterior work, keelsons, tough, reddish brown in color,
risings, filling pieces, clamps, resinous, medullary rays well marked
floors, bulkheads of small
boats, shores, wedges, plugs,
strongbacks, staging, joists,
posts, piling, ties, paving
blocks
3-24
until dry. A faster method, known as kiln drying, has

lumber placed in a large oven or kiln and dried with
heat, supplied by gas- or oil-fired burners. Lumber is
considered dry enough for most uses when its moisture
content has been reduced to about 12 or 15 percent. As
a Builder, you will learn to judge the dryness of lumber
by its color, weight, smell, and feel. Also, after the
lumber is cut, you will be able to judge the moisture
content by looking at the shavings and chips.
LUMBER
The terms "wood" "lumber," and "timber" are

often spoken of or written in ways to suggest that their
meanings are alike or nearly so. But in the Builders
language, the terms have distinct, separate meanings.
Wood is the hard, fibrous substance that forms the
major part of the trunk and branches of a tree.
Lumber is wood that has been cut and surfaced for use
in construction work. Timber is lumber that is
5 inches or more in both thickness and width.
DEFECTS AND BLEMISHES
SEASONING OF LUMBER
A defect in lumber is any flaw that tends to affect

the strength, durability, or utility value of the lumber.
Seasoning of lumber is the result of removing
A blemish is a flaw that mars only the appearance of
moisture from the small and large cells of wood
lumber. However, a blemish that affects the utility
drying. The advantages of seasoning lumber are to value of lumber is also considered to be a defect; for
reduce its weight; increase its strength and resistance example, a tight knot that mars the appearance of
to decay; and decrease shrinkage, which tends to
lumber intended for fine cabinet work.
avoid checking and warping after lumber is placed. A
Various flaws apparent in lumber are listed in
seldom used and rather slow method of seasoning
table 3-2.
lumber is air-drying in a shed or stacking in the open
Table 3-2.Wood Defects and Blemishes
COMMON NAME
Bark Pocket
Check
Cross Grain
Decay
Knot
Pitch Pocket
DESCRIPTION
Patch of bark over which the tree has grown, and has entirely or almost entirely
enclosed
Separation along the lengthwise grain, caused by too rapid or nonuniform drying
Grain does not run parallel to or spiral around the lengthwise axis
Deterioration caused by various fungi
Root section of a branch that may appear on a surface in cross section or lengthwise.
A cross-sectional knot maybe loose or tight. A lengthwise knot is called a spike knot
Deposit of solid or liquid pitch enclosed in the wood
Shake
Separation along the lengthwise grain that exists before the tree is cut. A heart shake
moves outward from the center of the tree and is caused by decay at the center of the
trunk. A wind shake follows the circular lines of the annual rings; its cause is not
definitely known
Wane
Flaw in an edge or corner of a board or timber. It is caused by the presence of bark or

lack of wood in that part
Warp
Twist or curve caused by shrinkage that develops in a once flat or straight board
Blue Stain
A blemish caused by a mold fungus; it does not weaken the wood
3-25
that has been planed on one or more sides to attain

smoothness and uniformity. Worked lumber, in
addition to being dressed, has also been matched,
Trees are classified as either softwood or
shiplapped, or patterned. Matched lumber is tongue
hardwood (table 3-3). Therefore, all lumber is
and
groove, either sides or ends or both. Shiplapped
referred to as either softwood or hardwood. The
lumber
has been rabbeted on both edges to provide a
terms softwood and hardwood can be confusing
close-lapped
joint. Patterned lumber is designed to a
since some softwood lumber is harder than some
hardwood lumber. Generally, however, hardwoods pattern or molded form.
CLASSIFICATION OF LUMBER
are more dense and harder than softwoods. In

addition, lumber can be further classified by the name Softwood Grading
For example,
of the tree from which it comes.
The grade of a piece of lumber is based on its
Douglas fir lumber comes from a Douglas fir tree;
walnut lumber comes from a walnut tree, and so forth. strength, stiffness, and appearance. A high grade of
lumber has very few knots or other blemishes. A low
The quality of softwood lumber is classified
grade of lumber may have knotholes and many loose
according to its intended use as being yard, structural, knots. The lowest grades are apt to have splits,
factory, or shop lumber. Yard lumber consists of
checks, honeycombs, and some warpage. The grade
those grades, sizes, and patterns generally intendedof lumber to be used on any construction job is
for ordinary building purposes. Structural lumber is 2 usually stated in the specifications for a set of
or more inches in nominal thickness and width and is blueprints. Basic classifications of softwood grading
used where strength is required. Factory and shop include boards, dimension, and timbers. The grades
lumber are used primarily for building cabinets and within these classifications are shown in table 3-4.
interior finish work.
Lumber is graded for quality in accordance with
Lumber manufacturing classifications consist of American Lumber Standards set by the National
rough dressed (surfaced) and worked lumber. Rough Bureau of Standards for the U.S. Department of
lumber has not been dressed but has been sawed, Commerce. The major quality grades, in descending
edged, and trimmed. Dressed lumber is rough lumber order of quality, are select lumber and common
Table 3-3.-Different Types of Softwoods and Hardwoods

SOFTWOODS
HARDWOODS
Douglas fir
Southern pine
Western larch
Basswood
Willow
American elm
Hemlock
White fir
Spruce
Mahogany*
Sweet gum
White ash*
Ponderosa pine
Western red cedar
Redwood
Beech
Birch
Cherry
Cypress
White pine
Sugar pine
Maple
Oak*
Walnut*
*Open-grained wood
3-26
Table 3-4.-Softwood Lumber Grades
3-27
Lumber in this group is expected to yield 6623

percent clear cuttings.
lumber. Table 3-5 lists the subdivisions for each

grade in descending order of quality.
Lumber Sizes
Hardwood Grades
Standard lumber sizes have been established in

Grades of hardwood lumber are established by the the United States for uniformity in planning structures
National Hardwood Lumber Association. FAS (firsts and in ordering materials. Lumber is identified by
and seconds) is the best grade. It specifies that pieces nominal sizes. The nominal size of a piece of lumber
be no less than 6-inches wide by 8-feet long and yield is larger than the actual dressed dimensions.
at least 83 1/3 percent clear cuttings. The next lowerReferring to table 3-6, you can determine the common
grade is selects, which permits pieces 4-inches wide widths and thicknesses of lumber in their nominal and
by 6-feet long. A still lower grade is No. 1 common. dressed dimensions.
Table 3-5.-Grades and Subdivisions of Lumber
SELECT LUMBER
Grade A
This lumber is practically free of defects and blemishes
Grade B
This lumber contains a few minor blemishes
Grade C
This lumber contains more numerous and more significant blemishes than grade
B. It must be capable of being easily and thoroughly concealed with paint
Grade D
This lumber contains more numerous and more significant blemishes than grade
C, but it is still capable of presenting a satisfactory appearance when painted
COMMON LUMBER
No. 1
Sound, tight-knotted stock containing only a few minor defects. Must be

suitable for use as watertight lumber
No. 2
Contains a limited number of significant defects but no knotholes or other

serious defects. Must be suitable for use as grain-tight lumber
No. 3
Contains a few defects that are larger and coarser than those in No. 2 common;
for example, occasional knotholes
No. 4
Low-quality material containing serious defects like knotholes, checks, shakes,

and decay
No. 5
Capable only of holding together under ordinary handling
3-28
Table 3-6.-Nominal and Dressed Sizes of Lumber
Figure 3-29.-Laminated lumber.
LAMINATED LUMBER
Laminated lumber (figure 3-29) is made of
several pieces of lumber held together as a single unit,
a process called lamination. Usually 1 1/2-inches
thick, the pieces are nailed, bolted, or glued together
with the grain of all pieces running parallel.
Laminating greatly increases the load-carrying
capacity and rigidity of the weed. When extra length
is needed, the pieces are splicedwith the splices
staggered so that no two adjacent laminations are
spliced at the same point. Built-up beams and girders
are examples. They are built as shown in figure 3-30,
usually nailed or bolted together, and spliced.
Lamination can be used independently or with other
materials in the construction of a structural unit. Trusses
can be made with lamination for the chords and sawed
Figure 3-30.-Built-up beam.
3-29
Figure 3-31.-Truss using laminated and sawed lumber.

width. The depth of the lamination is placed in a
lumber, or for the web members (figure 3-31).
horizontal
position and is usually the fullwidth of the
Special beams can be constructed with lamination for
beam (figure 3-35).
the flanges and plywood or sawed lumber, for the
web, as shown in figure 3-32. Units, such as plywood
box beams and stressed skin panels, can contain both PLYWOOD
plywood and lamination (figure 3-33).
Plywood is constructed by gluing together a
Probably the greatest use of lamination is in the
wood with the grain
fabrication of large beams and arches. Beams with number of layers (plies) of
direction turned at right angles in each successive
spans in excess of 100 feet and depths of 8 1/2 feet
layer. This design feature makes plywood highly
have been constructed using 2-inch boards.
resistant to splitting. It is one of the strongest
Laminations this large are factory produced. They are
building materials available to Seabees. An odd
glued together under pressure. Most laminations are
number (3, 5, 7) of plies is used so that they will be
spliced using scarf joints (figure 3-34), and the entire
balanced on either side of a center core and so that the
piece is dressed to ensure uniform thickness and
grain of the outside layers runs in the same direction.
The outer plies are called faces or face and back. The
next layers under these are called crossbands, and the
other inside layer or layers are called the core
(figure 3-36). A plywood panel made of three layers
would consist of two faces and a core.
Figure 3-32.-Laminated and sawed lumber or plywood beam.
3-30
Figure 3-33.-Stressed skin panel.
Figure 3-34.-Scarf joints.
Figure 3-35.-Laminated beam.

There are two basic types of plywood: exterior
and interior. Exterior plywood is bonded with
waterproof glues. It can be used for siding, concrete
forms, and other constructions where it will be
exposed to the weather or excessive moisture.
Interior plywood is bonded with glues that are not
waterproof. It is used for cabinets and other inside
construction where the moisture content of the panels
will not exceed 20 percent.
Figure 3-36.-Grain direction in a sheet of plywood.
Plywood is made in thicknesses of 1/8 inch to

more than 1 inch, with the common sizes being 1/4,
3/8, 1/2, 5/8, and 3/4 inch. A standard panel size is
4-feet wide by 8-feet long. Smaller size panels are
available in the hardwoods.
3-31
Table 3-7.-Plywood Veneer Grades
Table 3-8.-Classification of Softwood Plywood Rates Species for Strength and Stiffness
3-32
Plywood can be worked quickly and easily with

common carpentry tools. It holds nails well and
normally does not split when nails are driven close to
the edges. Finishing plywood presents no unusual
problems; it can be sanded or texture coated with a
permanent finish or left to weather naturally.
There is probably no other building material as
versatile as plywood. It is used for concrete forms, wall
and roof sheathing, flooring, box beams, soffits,
stressed-skin panels, paneling, shelving, doors,
furniture, cabinets, crates, signs, and many other items.
Softwood Plywood Grades

All plywood panels are quality graded based on
products standards (currently PS 1/74). The grade of
each type of plywood is determined by the kind of
veneer (N, A, B, C, or D) used for the face and back of
the panel and by the type of glue used in construction.
The plywood veneer grades are shown in table 3-7.
Many species of softwood are used in making
plywood. There are five separate plywood groups
based on stiffness and strength. Group 1 includes the
stiffest and strongest; group 5 includes the weakest
woods. A listing of groupings and associated woods
is shown in table 3-8.
GRADE/TRADEMARK STAMP. Construction and industrial plywood panels are marked with
different stamps.
Construction Panels. Grading identification
stamps (such as those shown in figure 3-37) indicate
the kind and type of plywood. The stamps are placed
on the back and sometimes on the edges of each sheet
of plywood.
For example, a sheet of plywood having the
designation A-C would have A-grade veneer on the
face and C-grade veneer on the back. Grading is also
based on the number of defects, such as knotholes,
pitch pockets, splits, discolorations, and patches in the
face of each panel. Each panel or sheet of plywood
has a stamp on the back that gives all the information
you need. Table 3-9 lists some uses for constructiongrade plywood.
Industrial Panels. Structural and sheeting
panels have a stamp found on the back. A typical
example for an industrial panel grade of plywood is
The span rating shows a pair of numbers
separated by a slash mark (/). The number on the left
indicates the maximum recommended span in inches
when the plywood is used as roof decking (sheeting).
The right-hand number applies to span when the
plywood is used as subflooring. The rating applies
only when the sheet is placed the long dimension
across three or more supports. Generally, the larger
the span rating, the greater the stiffness of the panel.
Figure 3-39 lists some typical engineered grades
of plywood. Included are descriptions and most
common uses.
Figure 3-37.-Standard plywood identification symbols.
Figure 3-38.-Structural stamp.
3-33
Table 3-9.-Plywood Uses

SOFTWOOD PLYWOOD GRADES FOR EXTERIOR USES
Grade
(Exterior)
Face
Back
Inner Plies
A-A
Outdoor where appearance of both

sides is important
A-B
Alternate for A-A where appearance of

one side is less important
A-C
Siding, soffits, fences. Face is finish

grade
B-C
For utility uses, such as farm

buildings, some kinds of fences, etc.
C-C
(Plugged)
C
(Plugged)
Excellent base for tile and linoleum,

backing for wall coverings
C-C
Unsanded, for backing and rough

construction exposed to weather
B-B
Concrete
Forms
Concrete forms. Reuse until wood

literally wears out
MDO
B or C
C or
C-Plugged
Medium density overlay. Ideal base

for paint; for siding, built-ins, signs,
displays
HDO
A or B
A or B
C-Plugged
High density overlay. Hard surface;

no paint needed. For concrete forms,
cabinets, counter tops, tanks
Uses
SOFTWOOD PLYWOOD GRADES FOR INTERIOR USES

Grade
(Interior)
Face
Back
Inner Plies
A-A
Cabinet doors, built-ins, furniture

where both sides will show
A-B
Alternate of A-A. Face is finish grade,

back is solid and smooth
A-D
Finish grade face for paneling,

built-ins, backing
B-D
Utility grade. One paintable side. For

backing, cabinet sides, etc
Standard
Sheathing and structural uses such as

temporary enclosures, subfloor.
Unsanded
3-34
Uses
Figure 3-39.-List of engineered grade of softwood plywood.
3-35
Exposure Ratings. The grade/trademark stamp Most plywood is made withwaterproof exterior
lists the exposure durability classification for plywood. glue. However, interior panels may be made with
There are two basic types or ratings: exterior and
intermediate or interior glue.
interim. The exterior type has a 100-percent waterproof
glue line, and the interior type has a highly
Hardwood Plywood Grades
moisture-resistant glue line. However, panels can be
manufactured in three exposure durability
Hardwood plywood panels are primarily used for
classifications: Exterior, Exposure 1, and Exposure 2.
door
skins, cabinets, and wall paneling. The
Panels marked Exterior can be used where there
Hardwood
Plywood Manufacturers Association has
is continual exposure to weather and moisture. Panels
established
a grading system with the following
marked Exposure 1 can withstand moisture during
grades: premium (A), good grade (1), sound grade
extended periods, but they should be used only
indoors. Panels marked Exposure 2 can be used in (2), utility grade (3), and backing grade (4). For
protected locations. They may be subjected to some example, an A-3 grade hardwood plywood would
water leakage or high humidity but generally should have a premium face and a utility back. A 1-1 grade
would have a good face and a good back.
be protected from weather.
Figure 3-40.-Planing and squaring to dimensions.
3-36
Figure 3-41.-90 plain butt Joints.
making joints are (1) laying out the joint on the ends,
edges, or faces and (2) cutting the members to the
required shapes for joining.
WOODWORKING METHODS
various methods and joints associated with
woodworking.
The instruments normally used for laying out

joints are the try square, miter square, combination
square, the sliding T-bevel, the marking or mortising
gauge, a scratch awl, and a sharp pencil or knife for
scoring lines. For cutting the more complex joints by
hand, the hacksaw dovetail saw and various chisels
are essential. The rabbet-and-fillister plane (for
rabbet joints) and the router plane (for smoothing the
bottoms of dadoes and gains) are also helpful.
In the following section, we will cover some of

the methods used by Builders in joining wood.
PLANING AND SQUARING TO
DIMENSIONS
Planing and squaring a small piece of board to
dimensions is what you might call the first lesson in
woodworking. Like many other things you may have
tried to do, it looks easy until you try it. The six major
steps in this process are illustrated and described in
figure 3-40. You should practice these steps until you
can get a smooth, square board with a minimum of
planing.
Simple joints, like the butt (figures 3-41 and

3-42), the lap (figure 3-43), and the miter joints
JOINTS AND JOINING

One basic skill of woodworking is the art of
joining pieces of wood to form tight, strong,
well-made joints. The two pieces that are to be joined
together are called members. The two major steps in
Figure 3-43.-Lap Joints.
Figure 3-42.-End butt joints with fishplates.
3-37
Figure 3-44.-Miter joints.
Figure 3-45.-Rabbet joints.
Figure 3-46.-Dado and gain joints.
3-38
Figure 3-47.-Tenon joints.
(figure 3-44), are used mostly in rough or finish

carpentry though they may be used occasionally in
millwork and furniture making. More complex joints,
like the rabbet joints (figure 3-45), the dado and gain
joints (figure 3-46), the blind mortise-and-tenon and
slip-tenon joints (figure 3-47), the box corner joint
(figure 3-48), and the dovetail joints (figure 3-49), are
used mostly in making furniture and cabinets and in
Figure 3-49.-Dovetail joints.
Figure 3-48.-BOX corner joint.
3-39
millwork. Of the edge joints shown in figure 3-50,

the dowel and spline joints are used mainly in
furniture and cabinet work, whereas the plain butt and
the tongue-and-groove joints are used in practically
all types of woodworking.
The method of laying out and cutting an end butt half

lap (figure 3-43) is to measure off the desired amount
of lap from each end of each member and square a
line all the way around at this point. For a corner half
lap (figure 3-43), measure off the width of the
member from the end of each member and square a
line all the way around. These lines are called
shoulder lines.
The joints used in rough and finished carpentry

are, for the most part, simply nailed together. Nails in
a 90 plain butt joint can be driven through the
member abutted against and into the end of the
Next, select the best surface for the face and set a
abutting member. The joints can also be toenailed at marking gauge to one-half the thickness and score a
an angle through the faces of the abutting member line (called the cheek line) on the edges and end of
into the face of the member abutted against, as shown each member from the shoulder line on one edge to
in figure 3-51. Studs and joists are usually toenailed the shoulder line on the other edge. Be sure to gauge
to soleplates and sills.
the cheek line from the face of each member. This
The more complex furniture and cabinet-making ensures that the faces of each member will be flush
after the joints are cut.
joints are usually fastened with glue. Additional
strength can be provided by dowels, splines,
Next, make the shoulder cuts by cutting along the
corrugated fasteners, keys, and other types of joint waste side of the shoulder lines down to the waste side
fasteners. In the dado joint, the gain joint, the
of the cheek line. Then, make the cheek cuts along the
mortise-and-tenon joint, the box corner joint, and the waste side of the cheek lines. When all cuts have been
dovetail joint, the interlocking character of the joint is made, the members should fit together with faces,
an additional factor in fastening.
ends, and edges flush or near enough to be made flush
All the joints we have been mentioned can be cut with the slight paring of a wood chisel.
either by hand or by machine. Whatever the method
Other half-lap joints are laid out in a similar
used and whatever the type of joint, remember: To
manner. The main difference is in the method of
ensure a tight joint, always cut on the waste side of the
cutting. A cross half-lap joint may best be cut with a
line; never on the line itself. Preliminary grooving on
dado head or wood chisel rather than a handsaw.
the waste side of the line with a knife or chisel will
Others may easily be cut on a bandsaw, being certain
help a backsaw start smoothly.
Half-Lap Joints
For half-lap joints, the members to be jointed are
usually of the same thickness, as shown in figure 3-43.
Figure 3-50.-Edge Joints.
Figure 3-51.Toenailing.
3-40
to cut on the waste side of the lines and making all

lines from the face of the material.
Miter Joints
A miter joint is made by mitering (cutting at an
angle) the ends or edges of the members that are to be
joined together (figure 3-44). The angle of the miter
cut is one-half of the angle formed by the joined
members. In rectangular mirror frames, windows,
door casing boxes, and the like, adjacent members
form a 90 angle, and, consequently, the correct angle
for mitering is one-half of 90, or 45. For members
forming an equal-sided figure with other than four
sides (such as an octagon or a pentagon), the correct
mitering angle can be found by dividing the number
of sides the figure will have into 180 and subtracting
the result from 90. For an octagon (an eight-sided
figure), determine the mitering angle by subtracting
from 90 divided by 8 or 90 minus 22.5 equals
67.5. For a pentagon (a five-sided figure), the angle is
Members can be end mitered to 45 in the wooden

miter box and to any angle in the steel miter box by
setting the saw to the desired angle, or on the circular
saw, by setting the miter gauge to the desired angle.
Members can be edge mitered to any angle on the
circular saw by tilting the saw to the required angle.
Figure 3-52.-Beveling on a jointer for a mitered edge joint.
into a kerf cut in the thickest dimension of the joint.

First, saw about halfway through the wood from the
outer to the inner corner, then apply glue to both sides
of the slip feather, pushing the slip feather into the
kerf. Clamp it tightly and allow the glue to dry. After
it has dried, remove the clamp and chisel off the
protruding portion of the slip feather.
Sawed edges are sometimes unsuitable for gluing.

However, if the joint is to be glued, the edges can be
mitered on a jointer, as shown in figure 3-52.
SAFETY NOTE
This is a dangerous operation and caution
should be taken.
A joint between edge-mitered members can also

be reinforced with a spline. This is a thick piece of
wood that extends across the joint into grooves cut in
the abutting surfaces. A spline for a plain miter joint
is shown in figure 3-44. The groove for a spline can
be cut either by hand or by a circular saw.
Grooved Joints
Since abutting surfaces of end-mitered members

do not hold well when they are merely glued, they
should be reinforced. One type of reinforcement is
the corrugated fastener. This is a corrugated strip of
metal with one edge sharpened for driving into the
joint. The fastener is placed at a right angle to the line
between the members, half on one member and half
on the other, and driven down flush with the member.
The corrugated fastener mars the appearance of the
surface into which it is driven; therefore, it is used
only on the backs of picture frames and the like.
A more satisfactory type of fastener for a joint
between end-mitered members is the slip feather.
This is a thin piece of wood or veneer that is glued
3-41
A three-sided recess running with the grain is called

a groove, and a recess running across the grain is called
a dado. A groove or dado that does not extend all the
way across the wood is called a stopped groove or a
stopped dado. A stopped dado is also known as a gain
(figure 3-46). A two-sided recess running along an edge
is called a rabbet T (figure 3-45). Dadoes, gains, and
rabbets are not, strictly speaking, grooves; but joints that
include them are generally called grooved joints.
A groove or dado can be cut with a circular saw as
follows: Lay out the groove or dado on the end wood
(for a groove) or edge wood (for a dado) that will first
come in contact with the saw. Set the saw to the
desired depth of the groove above the table, and set
the fence at a distance from the saw that will cause the board barely contacts the right side of the dado head.
first cut to run on the waste side of the line that
Set the piece against the miter gauge (set at 90), hold
indicates the left side of the groove. Start the saw and the edge or end to be rabbeted against the l-inch
bring the wood into light contact with it; then stop the board, and make the cut.
saw and examine the layout to ensure the cut will be
On some jointers, a rabbeting ledge attached to
on the waste side of the line. Readjust the fence, if
the
outer edge of the infeed table can be depressed for
necessary. When the position of the fence is right,
rabbeting,
as shown in figure 3-53. The ledge is
make the cut. Then, reverse the wood and proceed to
located
on
the
outer end of the butterhead. To rabbet
set and test as before for the cut on the opposite side
on
a
jointer
of
this type, you depress the infeed table
of the groove. Make as many recuts as necessary to
and the rabbeting ledge the depth of the rabbet below
remove the waste stock between the side kerfs.
the outfeed table, and set the fence the width of the
The procedure for grooving or dadoing with the rabbet away from the outer end of the butterhead.
dado head is about the same, except that, in many When the piece is fed through, the unrabbeted part
cases, the dado head can be built up to take out all the feeds onto the rabbeting ledge. The rabbeted portion
waste in a single cut. The two outside cutters alone feeds onto the outfeed table.
will cut a groove 1/4 inch wide. Inside cutters vary in
Various combinations of the grooved joints are
thickness from 1/16 to 1/4 inch.
used in woodworking. The tongue-and-groove joint
A stopped groove or stopped dado can be cut on
is a combination of the groove and the rabbet, with the
the circular saw, using either a saw blade or a dado
tongued member rabbeted on both faces. In some types
head, as follows: If the groove or dado is stopped at
of paneling, the tongue is made by rabbeting only one
only one end, clamp a stop block to the rear of the
face. A tongue of this kind is called a barefaced
table in a position that will stop the wood from being
tongue. A joint often used in making boxes, drawers,
fed any farther when the saw has reached the place
and cabinets is the dado and rabbet joint, shown in
where the groove or dado is supposed to stop. If the
figure 3-54. As you can see, one of the members is
groove or dado is stopped at both ends, clamp a stop
rabbeted on one face to form a barefaced tongue.
block to the rear of the table and a starting block to the
front. The starting block should be placed so the saw
will contact the place where the groove is supposed to Mortise-and-Tenon Joints
start when the infeed end of the piece is against the
block. Start the cut by holding the wood above the saw,
The mortise-and-tenon joint is most frequently
with the infeed end against the starting block and the used in furniture and cabinet work. In the blind
edge against the fence. Then, lower the wood gradually mortise-and-tenon joint, the tenon does not penetrate
onto the saw, and feed it through to the stop block.
A rabbet can be cut on the circular saw as follows:
The cut into the face of the wood is called the
shoulder cut, and the cut into the edge or end, the
cheek cut. To make the shoulder cut (which should be
made first), set the saw to extend above the table a
distance equal to the desired depth of the cheek. Be
sure to measure this distance from a sawtooth set to
the left, or away from the ripping fence. If you
measure it from a tooth set to the right or toward the
fence, the cheek will be too deep by an amount equal
to the width of the saw kerf.
By using the dado head, you can cut most
ordinary rabbets in a single cut. First, build up a dado
head equal in thickness to the desired width of the
cheek. Next, set the head to protrude above the table
a distance equal to the desired depth of the should.
Clamp a 1-inch board to the fence to serve as a guide
Figure 3-53.-Rabbeting on a jointer with a rabbeting ledge.
for the piece, and set the fence so the edge of the
3-42
Figure 3-56.-Layout of stub mortise-and-tenon

joint.
Figure 3-54.-Dado and rabbet joint.
all the way through the mortised member (figure 3-47).

A joint in which the tenon does penetrate all the
way through is a through mortise-and-tenon joint (figure
3-55). Besides the ordinary stub joint (view A), there are
haunched joints (view B) and table-haunched joints
(view C). Haunching and table-haunching increase the
strength and rigidity of the joint.
The layout procedure for an ordinary stub
mortise-and-tenon joint is shown in figure 3-56. The
shoulder and cheek cuts of the tenon are shown in
figures 3-57 and 3-58. To maintain the stock upright
while making the cheek cuts, use a push board similar to
the one shown in figure 3-58. Tenons can also be cut
with a dado head by the same method previously
described for cutting end half-lap joints.
Figure 3-55.-Stub (view A), haunched (view B), and

table-haunched (view C) mortise-and-tenon joints.
3-43
103.22
Figure 3-57.-Making tenon shoulder cut on a table
saw.
103.23
Figure 3-58.-Making tenon cheek cut on a table
saw using a push board.
Figure 3-60.-Dovetail half-lap Joint.

Dovetail Joints
The dovetail joint (figure 3-49) is the strongest of
all the woodworking joints. It is used principally for
joining the sides and ends of drawers in fine grades of
furniture and cabinets. In the Seabee units, you will
seldom use dovetail joints since they are laborious
and time-consuming to make.
A through dovetail joint is a joint in which the
pins pass all the way through the tail member. Where
the pins pass only part way through, the member is
known as a blind dovetail joint.
103.24
Figure 3-59.-Hollow-chisel mortising machine.
Mortises are cut mechanically on a hollow-chisel
mortising machine like the one shown in figure 3-59.
The cutting mechanism on this machine consists of a
boring bit encased in a square, hollow, steel chisel. As
the mechanism is pressed into the wood, the bit takes
out most of the waste while the chisel pares the sides
of the mortise square. Chisels come in various sizes,
with corresponding sizes of bits to match. If a
mortising machine is not available, the same results
can be attained by using a simple drill press to take
out most of the waste and a hand chisel, for paring
the sides square.
The simplest of the dovetail joints is the dovetail

half-lap joint, shown in figure 3-60. Figure 3-61
shows how this type of joint is laid out, and figure 362 shows the completed joint.
In some mortise-and-tenon joints, such as those

between rails and legs in tables, the tenon member is
much thinner than the mortise member. Sometimes a
member of this kind is too thin to shape in the
customary reamer, with shoulder cuts on both faces.
When this is the case, a barefaced mortise-and-tenon
joint can be used. In a barefaced joint, the tenon
member is shoulder cut on one side only. The cheek
on the opposite side is simply a continuation of the
face of the member.
Mortise-and-tenon joints are fastened with glue
and with additional fasteners, as required.
3-44
Figure 3-61.-Laying off 10 angle for dovetail

joint.
Figure 3-64.-Chiseling out waste in a through-multipledovetail joint.

Figure 3-62.-Making a dovetail half-lap joint.
A multiple dovetail joint is shown in figure 3-63;

figure 3-64 indicateshow the waste is chiseled from
the multiple joint.
Box Corner Joints
With the exception of the obvious difference in
the layout, the box corner joint (figure 3-48) is made
in a similar manner as the through-multiple-dovetail
joint.
Coping Joints
Inside corner joints between molding trim
members are usually made by butting the end of one
member against the face of the other. Figure 3-65
Figure 3-63.-Laying out a pin member for a throughmultiple-dovetail joint.
Figure 3-65.-Making a coping Joint.
3-45
Figure 3-66.-Simple molding and trim shapes.
Figure 3-67.-Typical dimensions for cabinetwork.
3-46
shows the method of shaping the end of the abutting

member to tit the face of the other member. First, saw
off the end of the abutting member square, as you
would for an ordinary butt joint between ordinary
flat-faced members. Then, miter the end to 45, as
shown in the first and second views of figure 3-65.
Set the coping saw at the top of the line of the miter
cut, hold the saw at 90 to the lengthwise axis of the
piece, and saw off the segment shown in the third
view, following closely the face line left by the 45
miter cut. The end of the abutting member will then
match the face of the other member, as shown in the
third view. A joint made in this reamer is called a
coping joint. You will have to cut coping joints on a
large variety of moldings. Figure 3-66 shows the
simplest and most common moldings and trims used
in woodworking.
MILLWORK
this section, you should be able to recognize the
various types of millwork products and
procedures.
As a general term, millwork usually embraces
most wood products and components that require
manufacturing. It not only includes the interior trim
and doors, but also kitchen cabinets and similar units.
Most of these units are produced in a millwork manufacturing plant and are ready to install. Figure 3-67 is
an example of the dimensions you might be working
with.
BUILDING CABINETS IN PLACE
One of the most common ways of building
cabinets, such as those shown in figure 3-68, is to cut
Figure 3-68.-Typical kitchen cabinets: wall (view A) and base (view B).
3-47
Figure 3-69.-Typical frame construction of a cabinet.
the pieces (figure 3-69) and assemble them in place.strips through the wall into the studs. At the inside
corners, end panels can be attached directly to the
Think of building in-place cabinets in four steps.
wall.
1. Construct the base first. Use straight 2-by-4
lumber for the base. Nail the lumber to the floor and
Remember to make your measurements for both
to a strip attached to the wall. If the floor is not level, base and wall units carefully, especially for openings
place shims under the various members of the base. for built-in appliances. Refer frequently to your
Later, you can face any exposed 2-by-4 surfaces withdrawings and specifications to ensure accuracy.
a finished material, or the front edge can be made of a
finished piece, such as base molding.
Shelves
2. Next, cut and install the end panels. Attach a
strip along the wall between the end panels and level
Shelves are an integral part of cabinetmaking,
with the top edge. Be sure the strip is level throughout
especially for wall units. Cutting dadoes into cabinet
its length. Nail it securely to the wall studs.
walls to fit in shelves may actually strengthen the
3. Cut the bottom panels and nail them in place cabinet (figure 3-70.) When adding shelves, try to
on the base. Follow this with the installation of the make them adjustable so the storage space can be
partitions, which are notched at the back corner of the altered as needed. Figure 3-71 shows two methods of
top edge so they will fit over the wall strip.
installing adjustable shelves.
4. Finally, plumb the front edge of the partitions
Whatever method of shelf support you use, make
and end panels. Secure them with temporary strips
sure that your measurements are accurate and the
nailed along the top.
shelves are level. Most of the time, you will find it
Wall units are made using the same basic steps as easier to do your cutting and drilling before you start
assembling the cabinets. If the shelf standards are the
the base units. You should make your layout lines
type that are set in a groove, you must cut the groove
directly on the ceiling and wall. Nail the mounting
3-48
Figure 3-70.-End panels of a wall cabinet in place (view A) and completed framing with facing partially
applied (view B).
before assembly. Some adjustable shelf supports can

be mounted on the surface.
Shelving supports for 3/4-inch shelves should be
placed no more than 42-inches apart. Shelves
designed to hold heavy loads should have closer
supports. To improve the appearance of plywood
shelving, cover the laminated edge with a strip of
wood that matches the stock used for the cabinet.
attached to the basic cabinet structure. The vertical

members of the facing are called stiles, and the
horizontal members are known as rails.
As previously mentioned for built-in-place
cabinets, you cut each piece and install it separately.
The size of each piece is laid out by positioning the
facing stock on the cabinet and marking it. Then, the
finished cuts are made, A cut piece can be used to lay
out duplicate pieces.
Cabinet Facing
After completing the frame construction and
shelving, apply finished facing strips to the front of
the cabinet frame. These strips are sometimes
assembled into a framework (called a faceplate or face
frame) by commercial sources before they are
Figure 3-71.-Two methods of supporting

shelves.
Cabinet stiles are generally attached first, then

the rails (figure 3-72). Sometimes a Builder will
attach a
Figure 3-72.-Facing being placed on a cabinet.
3-49
plumb end stile first, and then attach rails to determine

the position of the next stile.
The two general types of drawer faces are the lip

and flush faces (shown in figure 3-74, view B), A
flush drawer must be carefully fitted. A lip drawer
Use finishing nails and glue to install facing,
must have a rabbet along the top and sides of the
When nailing hardwoods, drill nail holes where you front. The lip style overlaps the opening and is much
think splitting might occur.
easier to construct.
Drawers
Cabinet Doors
Seabees use many methods of building drawers.

The four types of doors commonly used on
The three most common are the multiple dovetail, cabinets are the flush, lipped, overlay, and sliding
lock-shouldered, and square-shouldered methods
doors. A flush door, like the flush drawer, is the most
(figure 3-73).
difficult to construct. For a finished look, each type
of door must be fitted in the cabinet opening within
There are several types of drawer guides
1/16-inch clearance around all four edges. A lipped
available. The three most commonly used are the side door is simpler to install than a flush door since the
guide, the corner guide, and the center guide (shownlip, or overlap, feature allows you a certain amount of
in figure 3-74, view A).
adjustment and greater tolerances. The lip is formed
by cutting a rabbet along the edge.
Overlay doors are designed to cover the edges of
the face frame. There are several types of sliding
doors used on cabinets. One type of sliding door is
rabbeted to fit into grooves at the top and bottom of
the cabinet. The top groove is always made to allow
the door to be removed by lifting it up and pulling the
bottom out.
INSTALLING PREMADE CABINETS
To install premade cabinets, you can begin with
either the wall or base cabinets. The general
procedures for each are similar.
Installing the Wall Cabinets First
When layouts are made and wall studs located,
the wall units are lifted into position. They are held
with a padded T-brace that allows the worker to stand
close to the wall while making the installation. After
the wall cabinets are securely attached and checked,
the base cabinets are moved into place, leveled, and
secured.
Installing the Base Cabinets First
When base cabinets are installed first, the tops of
the base cabinets can be used to support braces that
Figure 3-73.-Three common types of joints used in drawer hold the wall units in place while they are fastened to
construction.
the wall.
3-50
6. After installing the cabinets and checking for

plumb and level, join the wall cabinets through the
sides as you did with the base cabinets.
Procedures
The following procedures are a simple way of
installing premade cabinets:
1. First, locate and mark the location of all wall
studs where the cabinets are to be hung. Find and
mark the highest point in the floor. This will ensure
the base cabinet is level on uneven floor surfaces.
(Shims should be used to maintain the cabinet at its
designated leveled height.)
7. Finally, after they are plumb and level, secure

the cabinets to the wall at the studs for maximum
holding power.
Here are some helpful hints for the general
construction of cabinets:
2. Start the installation of a base cabinet with a

corner or end unit. After all base cabinets are in
position, fasten the cabinets together. To get
maximum holding power from screws, place one hole
close to the top and one close to the bottom.
3. Starting at the highest point in the floor, level
the leading edges of the cabinets. After leveling all
the leading edges, fasten them to the wall at the studs
to obtain maximum holding power.
4. Next, install the countertop on the base
cabinets making sure to drill or screw through the top.
5. Then, make a brace to help support the wall
cabinets while they are being fastened. Start the wall
cabinet installation with a corner or end cabinet.
Make sure you check for plumb and level as you
install these cabinets.
Cabinet parts are fastened together with screws

or nails. They are set below the surface, and
the holes are filled with putty. Glue is used at
all joints. Clamps should be used to produce
better fitting, glued joints.
A better quality cabinet is rabbeted where the
top, bottom, back, and side pieces come
together. However, butt joints are also used. If
panels are less than 3/4-inch thick, a
reinforcing block should be used with the butt
joint. Fixed shelves are dadoed into the sides.
Screws should go through the hanging strips
and into the stud framing. Never use nails.
Toggle bolts are required when studs are
inaccessible. Join units by first clamping them
together and then, while aligned, install bolts
and T-nuts.
Figure 3-74.-Types of drawer guides (view A) and faces (view B).
3-51
METHODS OF FASTENING
COUNTERS AND TOPS

different types of fastening devices.
In cabinetwork, the counters and tops are covered

with a 1/16-inch layer of high-pressure plastic
laminate. Although this material is very hard, it does
A variety of metal fastening devices are used by
not possess great strength and is serviceable only
Seabees
in construction. Although nails are the most
when it is bonded to plywood, particle board, or wafer
wood. This base, or core material, must be smooth commonly used fastener, the use of staples to attach
wood structural members is growing. For certain
and is usually 3/4-inch thick.
operations, screws and bolts are required. In addition,
various metal devices exist for anchoring materials
into concrete, masonry, and steel.
Working Laminates
The increasing use of adhesives (glues and
Plastic laminates can be cut to rough size with a mastics) is an important development in the building
table saw, portable saw, or saber saw. Use a fine-tooth industry. Adhesives are used in combination with, or
blade, and support the material close to the cut. If no in place of, nails and screws.
electrical power is available, you can use a finish
handsaw or a hacksaw. When cutting laminates with
NAILS
a saw, place masking tape over the cutting area to help
prevent chipping the laminate. Make cut markings on
Nails, the most common type of metal fasteners,
the masking tape.
are available in a wide range of types and sizes.
Measure and cut a piece of laminate to the desired Basic Nail Types
size. Allow at least 1/4-inch extra to project past the
edge of the countertop surface. Next, mix and apply
Some basic types are shown in figure 3-75. The
the contact bond cement to the underside of the
common nail is designed for rough framing. The box
laminate and to the topside of the countertop surface. nail is used for toenailing and light work in frame
Be sure to follow the manufacturers recommended construction. The casing nail is used in finished
directions for application.
carpentry work to fasten doors and window casings
and other wood trim. The finishing nail and brad are
used for light, wood-trim material and are easy to
Adhering Laminates
drive below-the surface of lumber with a nail set.
Allow the contact bond cement to set or dry. To
check for bonding, press a piece of waxed brown
paper on the cement-coated surface. When no
adhesive residue shows, it is ready to be bonded. Be
sure to lay a full sheet of waxed brown paper across
the countertop. This allows you to adjust the laminate
into the desired position without permanent bonding.
Now, you can gradually slide the paper out from
under the laminate, and the laminate becomes bonded
to the countertop surface.
Be sure to roll the laminate flat by hand, removing
any air bubbles and getting a good firm bond. After
sealing the laminate to the countertop surface, trim
the edges by using either a router with a special guide
or a small block plane. If you want to bevel the
countertop edge, use a mill file.
3-52
Figure 3-75.-Basic types of nails.
The size of a nail is measured in a unit known as piece being fastened. Protruding nails should be bent
over to prevent damage to materials and injury to
a penny. Penny is abbreviated with the lowercase
personnel.
letter d. It indicates the length of the nail. A 6d
(6-penny) nail is 2-inches long. A 10d (10-penny) nail
There are a few general rules to be followed in the
is 3-inches long (figure 3-76). These measurements
use of nails in building. Nails should be driven at an
apply to common, box, casing, and finish nails only. angle slightly toward each other to improve their
Brads and small box nails are identified by their
holding power. You should be careful in placing nails
actual length and gauge number.
to provide the greatest holding power. Nails driven
A nail, whatever the type, should be at least
three times as long as the thickness of the wood it
is intended to hold. Two-thirds of the length of
the nail is driven into the other piece of wood for
proper anchorage. The other one-third of the
length provides the necessary anchorage of the
with the grain do not hold as well as nails driven

across the grain. A few nails of proper type and size,
properly placed and properly driven, will hold better
than a great many driven close together. Nails can
generally be considered the cheapest and easiest
fasteners to be applied.
Figure 3-76.-Nail sizes given in penny (d) units.
3-53
Specialty Nails
Heavy-duty staples are used to fasten plywood

sheeting and subflooring. Heavy-duty staples are
Figure 3-77 shows a few of the many specialized driven by electrically or pneumatically operated tools.
nails. Some nails are specially coated with zinc,
Light-duty and medium-duty staples are used for
cement, or resin materials. Some have threading for
attaching molding and other interior trim. Staples are
increased holding power of the nails. Nails are made
sometimes driven in by hand-operated tools.
from many materials, such as iron, steel, copper,
bronze, aluminum, and stainless steel.
SCREWS
Annular and spiral nails are threaded for greater
The use of screws, rather than nails, as fasteners
holding power. They are good for fastening paneling
may be dictated by a number of factors. These may
or plywood flooring. The drywall nail is used for
hanging drywall and has a special coating to preventinclude the type of material to be fastened, the
requirement for greater holding power than can be
rust. Roofing nails are not specified by the penny
system; rather, they are referred to by length. They obtained by the use of nails, the finished appearance
are available in lengths from 3/4 inch to 2 inches anddesired, and the fact that the number of fasteners that
can be used is limited. Using screws, rather than
have large heads. The double-headed nail, or
duplex-head nail, is used for temporary construction, nails, is more expensive in terms of time and money,
such as form work or scaffolding. The double head but it is often necessary to meet requirements for
on this nail makes it easy to pull out when forms or superior results. The main advantages of screws are
that they provide more holding power, can be easily
scaffolding are torn down. Nails for power nailing
tightened
to draw the items being fastened securely
come in rolls or clips for easy loading into a nailer.
They are coated for easier driving and greater holding together, are neater in appearance if properly driven,
power. Table 3-10 gives the general size and type of and can be withdrawn without damaging the material.
The common wood screw is usually made of
nails preferable for specific applications.
unhardened steel, stainless steel, aluminum, or brass.
STAPLES
The steel may be bright finished or blued, or zinc,
cadmium, or chrome plated. Wood screws are
Staples are available in a wide variety of shapes threaded from a gimlet point for approximately
and sizes, some of which are shown in figure 3-78. two-thirds of the length of the screw and are provided with a slotted head designed to be driven by
an inserted driver. Wood screws, as shown in
figure 3-79, are designated according to head style.
The most common types are flathead, oval head, and
Figure 3-77.-Specialized nails.
Figure 3-78.-Types of staples.
3-54
Table 3-10.-Size, Type, and Use of Nails
3-55
roundhead, as illustrated in that order in figure 3-79,

All of these screws can have slotted or Phillips heads.
To prepare wood for receiving the screws, bore a
body hole the diameter of the screw to be used in the
piece of wood that is to be fastened (figure 3-80). You
should then bore a starter hole in the base wood with
a diameter less than that of the screw threads and a
depth of one-half or two-thirds the length of the
Figure 3-80.-Proper way to sink a screw.
threads to be anchored. The purpose of this careful
preparation is to assure accuracy in the placement of
the screws, to reduce the possibility of splitting the
wood, and to reduce the time and effort required to lag screws are shown in table 3-11. Combined with
expansion anchors, they are used to frame timbers to
drive the screw. Properly set slotted and Phillips
existing masonry.
flathead and oval head screws are countersunk
Expansion shields, or expansion anchors as they
sufficiently to permit a covering material to be used to
are sometimes called, are used for inserting a
cover the head. Slotted roundhead and Phillips
roundhead screws are not countersunk, but they are predrilled hole, usually in masonry, to provide a
driven so that the head is firmly flush with the surface gripping base or anchor for a screw, bolt, or nail
of the wood. The slot of the roundhead screw is left intended to fasten an item to the surface in which the
hole was bored. The shield can be obtained separately,
parallel with the grain of the wood.
or it may include the screw, bolt, or nail. After the
The proper name for a lag screw (shown in
expansion shield is inserted in the predrilled hole, the
figure 3-79) is lag bolt or wood screw. These screws
fastener is driven into the hole in the shield,
are often required in constructing large projects, such
expanding the shield and wedging it firmly against the
as a building. They are longer and much heavier than
surface of the hole.
the common wood screw and have coarser threads
For the assembly of metal parts, sheet metal screws
that extend from a cone, or gimlet point, slightly more
are
used. These screws are made regularly in steel and
than half the length of the screw. Square-head and
brass with four types of heads: flat, round, oval, and
hexagonal-head lag screws are always externally
driven, usually by means of a wrench. They are used fillister, as shown in that order in figure 3-79.
when ordinary wood screws would be too short or too
Wood screws come in sizes that vary from 1/4 inch
light and spikes would not be strong enough. Sizes ofto 6 inches. Screws up to 1-inch in length increase by
Figure 3-79.-Types of screws.
3-56
Table 3-11.-Lag Screw Sizes
BOLTS
Bolts are used in construction when great strength is
required or when the work under construction must be
frequently disassembled. Their use usually implies the
use of nuts for fastening and, sometimes, the use of
washers to protect the surface of the material they are
used to fasten. Bolts are selected for application to specific requirements in terms of length, diameter, threads,
style of head, and type. Proper selection of head style
and type of bolt results in good appearance as well as
good construction. The use of washers between the nut
and a wood surface or between both the nut and the head
and their opposing surfaces helps you avoid marring the
surfaces and permits additional torque in tightening.
Carriage Bolts
eighths, screws from 1 to 3 inches increase by
quarters, and screws from 3 to 6 inches increase by
Carriage bolts fall into three categories: square
half inches. Screws vary in length and size of shaft. neck finned neck and ribbed neck (figure 3-82).
Each length is made in a number of shaft sizes
These bolts have round heads that are not designed to
specified by an arbitrary number that represents no
particular measurement but indicates relative
differences in the diameter of the screws. Proper
nomenclature of a screw, as shown in figure 3-81,
includes the type, material, finish, length, and screw
size number, which indicates the wire gauge of the
body, drill or bit size for the body hole, and drill or bit
size for the starter hole. Tables 3-12 and 3-13 provide
size, length, gauge, and applicable drill and auger bit
sizes for screws. Table 3-11 gives lengths and
diameters of lag screws.
Figure 3-81.-Types and nomenclature of wood screws.
3-57
Figure 3-82.-Types of bolts.
Table 3-12.-Screw Sizes and Dimensions
Table 3-13.-Drill and Auger Bit Sizes for Wood Screws
3-58
Table 3-14.-Carriage Bolt Sizes
be driven. They are threaded only part of the way up

the shaft. Usually, the threads are two to four times
the diameter of the bolt in length. In each type of
carriage bolt, the upper part of the shank, immediately
below the head, is designed to grip the material in
which the bolt is inserted and keep the bolt from
turning when a nut is tightened down on it or
removed. The finned type is designed with two or
more fins extending from the head to the shank. The
ribbed type is designed with longitudinal ribs, splines,
or serrations on all or part of a shoulder located
immediately beneath the head. Holes bored to receive
carriage bolts are bored to be a tight fit for the body of
the bolt and counterbored to permit the head of the
bolt to fit flush with, or below the surface of, the
material being fastened. The bolt is then driven
through the hole with a hammer. Carriage bolts are
chiefly for wood-to-wood application, but they can
also be used for wood-to-metal applications. If used
for wood-to-metal application, the head should be
fitted to the wood item. Metal surfaces are sometimes
predrilled and countersunk to permit the use of
carriage bolts metal to metal. Carriage bolts can be
obtained from 1/4 inch to 1 inch in diameter and from
3/4 inch to 20 inches long (table 3-14). A common
flat washer should be used with carriage bolts

between the nut and the surface.
Machine Bolts
Machine bolts (figure 3-82) are made with cut
national fine and national coarse threads extending in
length from twice the diameter of the bolt plus
1/4 inch (for bolts less than 6 inches in length) to
twice the diameter of the bolt plus 1/2 inch (for bolts
over 6 inches in length). They are precision made and
generally applied metal to metal where close
tolerance is desirable. The head may be square,
hexagonal, rounded, or flat countersunk. The nut
usually corresponds in shape to the head of the bolt
with which it is used. Machine bolts are externally
driven only. Selection of the proper machine bolt is
made on the basis of head style, length, diameter,
number of threads per inch, and coarseness of thread.
The hole through which the bolt is to pass is bored to
the same diameter as the bolt. Machine bolts are
made in diameters from 1/4 inch to 3 inches and may
be obtained in any length desired (table 3- 15).
Table 3-15.-Machine Bolt Sizes
3-59
Stove Bolts
Stove bolts (figure 3-82) are less precisely made
than machine bolts. They are made with either flat or
Figure 3-83.-Driftpin (driftbolt).
round slotted heads and may have threads extending
over the full length of the body, over part of the body,
or over most of the body. They are generally used
Driftpins
with square nuts and applied metal to metal, wood to
wood, or wood to metal. If flatheaded, they are
Driftpins are long, heavy, threadless bolts used to
countersunk. If roundheaded, they are drawn flush to hold heavy pieces of timber together (figure 3-83).
the surface.
They have heads that vary in diameter from 1/2 to
1 inch and in length from 18 to 26 inches. The term
driftpin is almost universally used in practice.
Expansion Bolt
However, for supply purposes, the correct designation
is driftbolt.
An expansion bolt (figure 3-82) is a bolt used in
conjunction with an expansion shield to provide
To use the driftpin, you make a hole slightly
anchorage in substances in which a threaded fastener smaller than the diameter of the pin in the timber. The
alone is useless. The shield, or expansion anchor, is pin is driven into the hole and is held in place by the
inserted in a predrilled hole and expands when the compression action of the wood fibers.
bolt is driven into it. It becomes wedged firmly in the
hole, providing a secure base for the grip of the
CORRUGATED FASTENERS
fastener.
The corrugated fastener is one of the many means
by
which
joints and splices are fastened in small
Toggle Bolts
timber and boards. It is used particularly in the miter
joint. Corrugated fasteners are made of 18- to
A toggle bolt (figure 3-82) is a machine screw
22-gauge sheet metal with alternate ridges and
with a spring-action, wing-head nut that folds back as
grooves; the ridges vary from 3/16 to 5/ 16 inch, center
the entire assembly is pushed through a prepared hole
to center. One end is cut square; the other end is
in a hollow wall. The wing head then springs open
sharpened with beveled edges. There are two types of
inside the wall cavity. As the screw is tightened, the
corrugated fasteners: one with the ridges running
wing head is drawn against the inside surface of the
parallel (figure 3-84, view A); the other with ridges
finished wall material. Spring-action, wing-head
running at a slight angle to one another (figure 3-84,
toggle bolts are available in a variety of machine
view B), The latter type has a tendency to compress
screw combinations. Common sizes range from 1/8
the material since the ridges and grooves are closer at
inch to 3/8 inch in diameter and 2 inches to 6 inches in
the top than at the bottom. These fasteners are made
length. They are particularly useful with sheetrock
in several different lengths and widths. The width
wall surfaces.
varies from 5/8 to 1 1/8 inches; the length varies from
1/4 to 3/4 inch. The fasteners also are made with
Molly Bolt
different numbers of ridges, ranging from three to six
ridges per fastener. Corrugated fasteners are used in a
number of waysto fasten parallel boards together,
The molly bolt or molly expansion anchor
(figure 3-82) is used to fasten small cabinets, towel as in fastening tabletops; to make any type of joint;
bars, drapery hangers, mirrors, electrical fixtures, and and as a substitute for nails where nails may split the
timber. In small timber, corrugated fasteners have
other lightweight items to hollow walls. It is inserted
in a prepared hole. Prongs on the outside of the shield greater holding power than nails. The proper method
of using the fasteners is shown in figure 3-84.
grip the wall surfaces to prevent the shield from
turning as the anchor screw is being driven. As the
screw is tightened, the shield spreads and flattens ADHESIVES
against the interior of the wall. Various sizes of screw
Seabees use many different types of adhesives in
anchors can be used in hollow walls 1/8 inch to 1 3/4
various phases of their construction projects. Glues
inches thick.
3-60
a good job of bonding wood together, and it sets up

(dries) quickly after being applied. Because white
glue is not waterproof, it should not be used on work
that will be subjected to constant moisture or high
humidity.
Urea resin is a plastic based glue that is sold in a
powder form. The required amount is mixed with
water when the glue is needed. Urea resin makes an
excellent bond for wood and has fair water resistance.
Phenolic resin glue is highly resistant to temperature extremes and water. It is often used for bonding
the veneer layers of exterior grade plywood.
Resorcinol glue has excellent water resistance
and temperature resistance, and it makes a very strong
bond. Resorcinol resin is often used for bonding the
wood layers of laminated timbers.
Contact cement is used to bond plastic laminates
to wood surfaces. This glue has a neoprene rubber
base. Because contact cement bonds very rapidly, it is
useful for joining parts that cannot be clamped
together.
Figure 3-84.-Corrugated fasteners and their uses.
(which have a plastic base) and mastics (which have

an asphalt, rubber, or resin base) are the two major
categories of adhesives.
The method of applying adhesives, their drying
time, and their bonding characteristics vary. Some
adhesives are more resistant to moisture and to hot
and cold temperatures than others.
SAFETY NOTE
Some adhesives are highly flammable;
they should be used only in a well-ventilated
work area. Others are highly irritating to the
ALWAYS FOLLOW
s k in a nd ey es .
MANUFACTURERS INSTRUCTIONS
WHEN USING ADHESIVES.
Glues
The primary function of glue is to hold together
joints in mill and cabinet work. Most modern glues
have a plastic base. Glues are sold as a powder to
which water must be added or in liquid form. Many
types of glue are available under brand names. A
brief description of some of the more popular types of
glue is listed below.
Mastics
Mastics are widely used throughout the construction industry. The asphalt, rubber, or resin base
of mastics gives them a thicker consistency. Mastics
are sold in cans, tubes, or canisters that fit into
hand-operated or air-operated caulking guns.
These adhesives can be used to bond materials
directly to masonry or concrete walls. If furring strips
are required on a wavy concrete wall, the strips can be
applied with mastic rather than by the more difficult
procedure of driving in concrete nails. You can also
fasten insulation materials to masonry and concrete
walls with a mastic adhesive. Mastics can also be
used to bond drywall (gypsum board) directly to wall
studs. They can also be used to bond gypsum board to
furring strips or directly to concrete or masonry walls.
Because you dont use nails, there are no nail
indentations to fill.
By using mastic adhesives, you can apply

paneling with very few or no nails at all. Wall panels
can be bonded to studs, furring strips, or directly
against concrete or masonry walls. Mastic adhesives
can be used with nails or staples to fasten plywood
panels to floor joists. The mastic adhesive helps
Polyvinyl resin, or white glue, is a liquid that
eliminate squeaks, bounce, and nail popping. It also
comes in ready-to-use plastic squeeze bottles. It does increases the stiffness and strength of the floor unit.
3-61
You therefore need to ensure that you are

studying the latest revision.
RECOMMENDED READING LIST

NOTE
Although the following references were
current when this TRAMAN was published,
their continued currency cannot be assured.
3-62
Carpentry I, Headquarters, EN5155, U.S. Army

Engineering School, Fort Belvoir, Va., 1988.
Carpentry III, Headquarters, EN0533, U.S. Army
Engineering School, Fort Belvoir, Va., 1987.

Woodworking Tools and Methods NAVEDTRA 14043

Uploaded by

Copyright:

Available Formats

Woodworking Tools and Methods NAVEDTRA 14043

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Woodworking Tools and Methods NAVEDTRA 14043

Uploaded by

Copyright:

Available Formats

CHAPTER 3

WOODWORKING TOOLS, MATERIALS, AND

are essential parts of your trade. To be a proficient

Figure 3-1.A shop radial arm saw.

the cutoff gauge, held firmly, and fed through by

The blade is held on the arbor by the arbor nut. A saw

The band saw has two large wheels on which a

Avoid the hazard of being hit by materials

Figure 3-3.Band saw.

saws are much the same with regard to maintenance,

A band saw should not be operated in a

A rule of thumb used by many Seabees is that the

Using a small saw blade for large work or

Blades, or bands, for band saws are designated by

Band saws should not be stopped by thrusting a

Keep your fingers away from the moving

Figure 3-4 shows a drill press. (The numbers in

The controls of all drill presses are similar. The

The on/off switch (11) is located in the front of

most cases, the quill lock handle will be in the

The spindle and quill feed handles (2) radiate

The head lock handle (5) is located at the left-rear

Figure 3-4.Drill press.

release the support. When operating the drill press,

The adjustable locknut (14) is located on the

The lathe is used in turning or shaping round

Observe the following safety precautions when

Figure 3-5 illustrates a type of lathe that you may

The woodworking lathe is, without question, the

Make sure that the drill is properly secured in

The lathe shown in figure 3-5 has an iron bed and

Make sure your material is properly secured.

The headstock is mounted on the left end of the

Listen for any sounds that may be signs of

Figure 3-5.A woodworking lathe with accessories.

in guiding tools along the work. It may be of any size

Figure 3-6.Lathe cutting tools.

chisels. Other cutting tools are toothing irons and

The tool rest must be used when milling stock.

Never attempt touse calipers on interrupted

The principle on which the jointer functions is

Figure 3-7.Toothing iron lathe tool.

Figure 3-8.Four-knife butterhead for a jointer.

held against the fence. A piece is surfaced by

Each hand-fed jointer should be equipped

Always plane with the grain. A piece of

Never place your hands directly over the

Figure 3-10.Operating principle of a

back, your hands will drop on the blades. Start

Never feed a piece of wood with your thumb

Avoid jointing short pieces of wood

Never use a jointer with dull cutter blades.

Keep the jointer table and the floor around

Never joint a piece of wood that contains

Keep your eyes and undivided attention on

straightens out any warp a piece may have; a piece

The cutting head should be covered by metal

Feed rolls should be guarded by a hood or a

Never force wood through the machine.