Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
438 views

Chapter 9 - Discrete Control Using PLC and PC

This document discusses discrete control systems and how programmable logic controllers (PLCs) and personal computers (PCs) can be used for discrete control. It covers the basics of logic control and sequencing, elements of logic control like AND, OR, and NOT gates, ladder logic diagrams, PLC components and operation cycle, and how soft logic software allows PCs to emulate PLC functions for discrete control.

Uploaded by

Anonymous 8NSojG
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
438 views

Chapter 9 - Discrete Control Using PLC and PC

This document discusses discrete control systems and how programmable logic controllers (PLCs) and personal computers (PCs) can be used for discrete control. It covers the basics of logic control and sequencing, elements of logic control like AND, OR, and NOT gates, ladder logic diagrams, PLC components and operation cycle, and how soft logic software allows PCs to emulate PLC functions for discrete control.

Uploaded by

Anonymous 8NSojG
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

Discrete Control Using PLCs and PCs

Discrete Control
-Discrete control systems deal with parameters and variables that
change at discrete moments in time.
-Parameters, variables are themselves are discrete, typically binary.
They can be either of two values-1 or 0, true or false, ON or OFF,
object present or not present, high voltage or low voltage
-Input signals to controller generally generated by binary sensors like
limit switch, photo sensors.
-Output turn on and off switches, motors, valves and other binary
actuators related to the process.
-Two categories are:
Logic control-concern with event driven changes
Sequencing- concern with time-driven changes in the system.

PLCs

Discrete Control Using PLCs and PCs


Logic Control
-A logic control system is a switching system whose output at any
moment is determined exclusively by the values of inputs. It has no
memory and does not consider previous values of inputs.
Example: A robot picks up a part at some point on a conveyor belt and
place the part into a forging press. To initiate the loading cycle
raw part must be at the specific point (simple limit switch can sense)
process on the previous part must be completed (machine can send
signal)
previous part must be removed from the die (a photo detector can
detect the presence or absence of the part)

Discrete Control Using PLCs and PCs


Elements of logic control
-Three basic elements of logic control:
AND-output is 1 only when all inputs are 1
OR-output is 1 if either of the inputs is 1
NOT-output is 1 when input is 0 and vise versa
-Two more elements are:
NAND-combining an AND and a NOT gates in sequence.
NOR-combining an OR and a NOT gates in sequence.

Discrete Control Using PLCs and PCs


AND-output is 1 only when all
inputs are 1

OR-output is 1 if either of the


inputs is 1

Source:http://www.technologystudent.com/elec1/dig2.htm

Discrete Control Using PLCs and PCs


Symbols and truth tables

Discrete Control Using PLCs and PCs


Example of logic network diagram
A push button switch consists of a box with two switches, one for
START and the other for STOP. When START button is depressed
momentarily by a human operator, power is supplied to a motor
until the stop button is pressed. What will be the logic network
diagram and truth table for the push-button switch?
Here, values of variables are:
START = 0 (normally open contact status)
START = 1 (when START is pressed)
STOP = 0 (normally closed contact status)
STOP = 1 (when STOP is pressed to break contact)
MOTOR = 0 when off
MOTOR = 1 when on
POWER-TO-MOTOR = 0 when contacts are open
POWER-TO-MOTOR = 1 when contacts are closed

Discrete Control Using PLCs and PCs


Example of logic network diagram

Here, values of variables are:


START = 0 (normally open contact status)
START = 1 (when START is pressed)
STOP = 0 (normally closed contact status)
STOP = 1 (when STOP is pressed to break
contact)
MOTOR = 0 when off
MOTOR = 1 when on
POWER-TO-MOTOR = 0 when contacts are
open
POWER-TO-MOTOR = 1 when contacts are
closed

Discrete Control Using PLCs and PCs


Sequencing
Uses internal timing devices to determine when to initiate
changes in the output variables.
Example : Washining machine, drier, dishwasher etc.
Industrial applications: heating by induction coil, in such case
there is no feed back (open-loop system).
Common sequencing elements: timer, drum timer, counters.

Discrete Control Using PLCs and PCs


Ladder Logic diagram
Exhibits the logic
(to some extent) timing
and sequencing
Looks like electrical
circuit
rung-horizontal lines
along which logic
elements and other
components are
displayed

Discrete Control Using PLCs and PCs


Ladder Logic diagram Examples

Top: Push button switch


Bottom: Control relay to actuate two motors

Discrete Control Using PLCs and PCs


PLC and its Components
PLC can be defined as a microcomputer-based controller
that uses stored instructions in programmable memory to
implement logic, sequencing, timing, counting, and
arithmetic functions through digital or analog input/output
modules, for controlling machines or process.
-Primarily associated with discrete manufacturing to control
machines, transfer lines, and material handling equipments.
Advantages of PLCs over relays: easier than wiring relay
control panel, reprogrammable, compact, more reliable,
more functionality

Discrete Control Using PLCs and PCs


PLC and its Components

Discrete Control Using PLCs and PCs


PLC and its Components
1.Processor: Executes various logic and sequencing functions based
on the PLC inputs to determine appropriate output.
2.Memory unit: contains the programs of logic, sequencing and I/O
operations. Also holds data files associated with these programs,
including input/output status bits, counter and timer constants,
and other variable and parameter values.
3.Power supply: supply the power required for the PLC and also to
operate some equipments.
4.I/O module: Provides the connection to the industrial equipment
or processes that is to controlled.
5.Programming device: is used to program PLC. Usually detachable
like teach pendant, keyboard with LCD/CRT display

Discrete Control Using PLCs and PCs


PLC Operation Cycle
Typical operation cycle of the PLC is know as SCAN. It consists of
three parts.
1.Input scan: inputs to the PLCs are read and stored in the memory.
2.Program scan: control program is executed during this scan. Input
values are used to determine appropriate outputs.
3.Output scan: outputs are update to agree with the calculated
values.
Scan time: time to perform the scan. It depends on number of inputs
to be read, complexity of the control function and number of
outputs that must be changed. It also depends on the clock speed of
the processor. Rang is 1~25msec.
What will happen if input changes faster than scan time?

Sample Microcontroller
ATmega328P

Discrete Control Using PLCs and PCs


PC Using Soft Logic
Before 90s, PLCs were always seen to have advantage of
being designed for harsh environment, with built in I/O
interface PLCs can be readily connected to the industrial
equipments. However compared to PLCs,
-PCs have much greater frequency than PLCs
-Speed of PC is increasing much more rapidly
-In case of PCs, proprietary software and architecture are
limited.
-PCs are now available in more sturdy enclosures, have
membrane type keyboard, I/O cards/hardware to interface
with the factory equipments are easily available.
-Now PCs have software (soft-logic) to emulate the operations
of the built-in software used in PLCs

You might also like