This document provides technical data and application instructions for Sikalastic-870 BT, a two-part, spray-applied polyurea membrane. It lists the product's uses for waterproofing steel and concrete in industrial applications, characteristics like chemical resistance and fast cure time, and application details such as substrate preparation and suitable equipment. The document also outlines physical property test results, packaging and storage information, and health and safety considerations.
This document provides technical data and application instructions for Sikalastic-870 BT, a two-part, spray-applied polyurea membrane. It lists the product's uses for waterproofing steel and concrete in industrial applications, characteristics like chemical resistance and fast cure time, and application details such as substrate preparation and suitable equipment. The document also outlines physical property test results, packaging and storage information, and health and safety considerations.
This document provides technical data and application instructions for Sikalastic-870 BT, a two-part, spray-applied polyurea membrane. It lists the product's uses for waterproofing steel and concrete in industrial applications, characteristics like chemical resistance and fast cure time, and application details such as substrate preparation and suitable equipment. The document also outlines physical property test results, packaging and storage information, and health and safety considerations.
This document provides technical data and application instructions for Sikalastic-870 BT, a two-part, spray-applied polyurea membrane. It lists the product's uses for waterproofing steel and concrete in industrial applications, characteristics like chemical resistance and fast cure time, and application details such as substrate preparation and suitable equipment. The document also outlines physical property test results, packaging and storage information, and health and safety considerations.
Edition 1, 2011 Identification no. xxx Version no. 0010
Sikalastic -870 BT (Resitect 5000)
Sikalastic -870 BT (Resitect 5000)
Spray applied polyurea membrane
Construction
Product Description Uses
Characteristics / Advantages
Sikalastic -870 BT is a two part, elastic, 100% solids, very fast curing polurea spray applied membrane where exposure to high acidic and alkaline chemical
concentrations are present. Sikalastic -870 BT is for machine application only.
For waterproofing applications on steel and concrete: Typical uses: Primary & secondary containments. Waste water treatment plants. Fertilizer plants and transportation Mines and mining processes. Ballast tanks. Silage tanks and troughs. Sludge digesters
High acidic and alkaline chemical resistance.
High resistance to microbial waste. Fast reactivity and cure time. Almost immediate return -to-service time. Applicable in temperature from -15C to 70C Performs in constant temperatures from -30C to 60C 100% solids Crack-bridging properties.
Product Data Tests Approval / Standards
Technologies for Concrete Structures of Sewage Works (Version of July 2007,
herein after referred to as J.S Manual) created by Japan Sewage Works Agency, Layering method for method categories C and D.
Form Appearance / Colour Packaging
ISO - Part A: Resin - Part B: Toner - Part C: Part A (net): Part B (net): Part C (net):
light yellow liquid
dark brown liquid standard Grey, othes on request 200.0 kg drum 175.0 kg drum 15.0 kg can
Storage Storage Conditions/ Shelf-Life
Part A: Part B: Part C:
6 months 12 months 12 months
From date of production if stored properly in original, unopened and undamaged
sealed packaging in dry conditions at temperatures between +5C and + 30C.
Sikalastic -870 BT
1/4
Technical Data Chemical Base Density
Gel Time Tack Free Time Curing Time Solid Content Mechanical / Physical Properties Tensile Strength Shore A Hardness Elongation at Break Tear Strength Water permeability Chloride ion permeability Resistance to alkali Resistance to impact Resistance Chemical Resistance
*No simultaneous chemical and mechanical exposure.
Application Details Consumption / Dosage
Coating System System for concrete structures
Products 1 x Resitect EP-F
Consumption 0.6 - 1.0 kg/m
1 x Sikalastic-871 JW
~1.10 kg/m/mm
The performance and technical properties are not affected by UV exposure.
Sikalastic -870 BT is UV light resistant, but not colour stable under UV exposure.
Substrate Quality
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level and wastage etc. The concrete substrate must be sound and of sufficient compressive strength 2 2 (minimum 25 N/mm ) with a minimum pull off strength of 1.5N/mm . The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc.
Substrate Preparation
If in doubt, apply a test area first.
Concrete substrates must be prepared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and achieve an open textured surface. Weak concrete must be removed and surface defects such as blowholes and voids must be fully exposed. Repairs to the substrate, filling of blowholes/voids and surface levelling must be
carried out using appropriate products from the Sikafloor , Sika Monotop or
SikaGard range of materials. (Acid resistance mortar is recommended)
The concrete or screed substrate has to be primed or levelled in order to achieve an even surface. High spots must be removed by e.g. grinding. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush and/or vacuum.
Sikalastic -870 BT
2/4
Application Conditions / Limitations Substrate Temperature Ambient Temperature Relative Air Humidity Substrate Moisture Content Dew Point Application Instructions Mixing
Test method: Sika -Tramex meter, CM -measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet) Beware of condensation! The substrate and uncured coating must be at least 3C above dew point to reduce the risk of condensation or blooming of the membrane finish.
Part A : Part B + Part C = 1 : 1 (by volume)
Dose and mix with suitable two-part spray equipment. Both components must be heated up. Comp A to +67C a nd +72C. Comp. B to +53C and +58C Pressure gap between comp. A and Comp . B should be controlled within 1 Mpa. The accuracy of mixing and dosage must be controlled regularly with the equipment.
Sikalastic -870 BT might not be diluted under any circumstances. Thoroughly mix
Sikalastic -870 BT part B resin material using a drum mixer until a homogenous mixture and colour is obtained. Prior to application, confirm substrate moisture content, r.h and dew point. Primer: Use current Primer, i.e. EP-F Prime prepared concrete with Resitect EP-F. The primer should not just be rolled or poured. In order to avoid the formation of pinholes, the primer must be troweled into the concrete surface, if necessary in two applications. Waterproofing: Add part C (toner) to part B and mix properly. Spray apply with suitable two-part hot spray high pressure equipment e.g. Graco Reactor E-XP2 Graco Reactor H-PX 3 (www.graco.com) or DFX-70S. The proportioning equipment utilized must be capable of supplying correct pressure and heat for the appropriate hose length on a consistent basis.
Cleaning of Tools Waiting Time / Over coating
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.
Before applying Sikalastic -870 BT on Resitect EP-F allow:
Substrate temperature +10C +20C +30C
Minimum 24 hours 24 hours 24 hours
Maximum 4 days ) 3 days ) 3 days )
Before applying Sikalastic -870 BT on Sikalastic -870 BT allow:
Substrate temperature +10C +20C +30C
Minimum 60 seconds
Maximum 8 hours ) 8 hours ) 8 hours )
) Assuming that any dirt has been carefully removed and contamination is avoided. ) If the max. waiting time is exceeded then hand abrade the entire surface using a moderate 200 to 300 grit sandpaper. Clean the grinded surface using Colam Reiniger. For larger areas Resi Primer-J must be applied as a bonding bridge. Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Sikalastic -870 BT
3/4
Notes on Application / Limitations
This product may only be used by experienced professionals.
Application by using 2-part hot spray high pressure equipment only. Basic temperature setting are: Part A: +67C Part B: +53C Temperature of the substrate during application and curing: min. +5C.
The performance and technical properties of Sikalastic -870 BT are not affected by
UV exposure. Sikalastic -870 BT is UV light resistant, but not colour stable under UV exposure. Please note: always apply a test area first.
Construction
Curing Details Applied Product ready for Use
Temperature
Rain resistant after
+5C +20C +30C
~ 3 minutes ~ 2 minutes ~ 1 minute
Ready for foot) traffic
(carefully) ~ 5 minutes ~ 3 minutes ~ 2 minutes
Ready for traffic)
~ 60 minutes ~ 45 minutes ~ 30 minutes
Note: ) Only for inspection or for application of the next layer. ) Only for inspection, application of the next layer Not for permanent traffic.
Times are approximate and will be affected by changing ambient conditions.
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
Local Restrictions
Please note that as a result of specific local regulations the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields.
Health and Safety
Information
For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety-related data.
Legal Notes
The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sikas current knowledge and experience of the product when properly stored, handled and applied under normal conditions in accordances with Sikas recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the products suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.
PT. Sika Indonesia
Jl. Raya Cibinong- Bekasi km. 20 Limusnunggal- Cileungsi BOGOR 16820 - Indonesia Tel. +62 21 8230025 Fax +62 21 8230026 Website : www.sika.co. id e-mail: sikacare@id.sika.com
Branches Surabaya : Komp. Pergudangan Meiko Abadi III Blok B-52 & B-53, Betro, Gedangan, Sidoarjo 61254 Tel : 031-8911333; Fax : 031-8916333 Medan : Jl. Pancing / Jl. Willem Iskandar No.66 B, Kec. Medan Tembung Tel : 061- 6619500; Fax : (061) 6619400 Batam : Jl. Laksamana Bintan, Komp. Bumi Riau Makmur Blok E No.3, Sungai Panas Tel : (0778) 424928; Fax : (0778) 450189
