Professional Documents
Culture Documents
Lte Cqi
Lte Cqi
The Channel Quality Indicator (CQI) contains information sent from a UE to the eNode-B to
indicate a suitable downlink transmission data rate, i.e., a Modulation and Coding Scheme
(MCS) value. CQI is a 4-bit integer and is based on the observed signal-to-interference-
plus-noise ratio (SINR) at the UE. The CQI estimation process takes into account the UE
capability such as the number of antennas and the type of receiver used for detection. This
is important since for the same SINR value the MCS level that can be supported by a UE
depends on these various UE capabilities, which needs to be taken into account in order for
the eNode-B to select an optimum MCS level for the transmission. The CQI reported values
are used by the eNode-B for downlink scheduling and link adaptation, which are important
features of LTE.
LTE supports wideband and subband CQI reporting. A wideband CQI value is a single 4-bit
integer that represents an effectiveSINR as observed by the UE over the entire channel
bandwidth. With wideband CQI, the variation in the SINR across the channel due to
frequency selective nature of the channel is masked out. Therefore, frequency selective
scheduling where a UE is placed only in resource blocks with high SINR is not possible with
wideband CQI reporting. To support frequency selective scheduling, each UE needs to report
the CQI with a fine frequency granularity, which is possible with subband CQI reporting. A
subband CQI report consists of a vector of CQI values where each CQI value is
representative of the SINR observed by the UE over a subband. A subband is a collection
of n adjacent Physical Resource Blocks (PRBs) where the value of n can be 2, 3, 4, 6, or 8
depending on the channel bandwidth and the CQI feedback mode.
In the plain words, CQI is an indicator carrying the information on how good/bad the
communication channel quality is.
CQI is the information that UE sends to the network and practically it implies the following
two
i) Current Communication Channel Quality is this-and-that..
ii) UE wants to get the data with this-and-that transport block size, which in turn can be
directly converted into throughput
For HSDPA, the CQI value ranges from 0 ~ 30. 30 indicates the best channel quality and 0,1
indicates the poorest channel quality. Depending which value UE reports, network transmit
data with different transport block size. If network gets high CQI value from UE, it transmit
the data with larger transport block size and vice versa.
What if network sends a large transport block even though UE reports low CQI, it is highly
probable that UE failed to decode it (cause CRC error on UE side) and UE send NACK to
network and the network have to retransmit it which in turn cause waste of radio resources.
What if UE report high CQI even when the real channel quality is poor ? In this case,
network would send a large transport block size according to the CQI value and it would
become highly probable that UE failed to decode it (cause CRC error on UE side) and UE
send NACK to network and the network have to retransmit it which in turn cause waste of
radio resources.
In LTE, there are 15 different CQI values randing from 1 to 15 and mapping between CQI
and modulcation scheme, transport block size is defined as follows (36.213)
If you are an engineer in Network (eNodeB) programming, you need to know the number of
resource blocks and MCS for each CQI value to properly allocate the resources for each of
UEs. With the modulation scheme in the table, you would get a certain range of MCS you
can use for each CQI index. But you cannot pinpoint a specific MCS and Number of RBs. You
need another condition to get the proper MCS and N RBs and it is 'Code Rate' shown in the
table. But still there is not a single formula that would give you a single/determined value
for MCS and NRB. You have to come up with a set of MCS and N RB that meet the
modulation scheme and Code Rate requirement in the table. One example case can be as
follows.
Note 1 : Refer to Throughtput Calculation Example for determining N_RB, MCS, TBS
determination.
Note 2 : REs/PRB varies depending on CFI value as follows.
CFI REs/PRB
1 150
2 138
3 126