Module 4 Lecture 1 Final PDF

NPTEL - Mechanical Engineering - Forming
Rolling - Introductory concepts
R. Chandramouli
Associate Dean-Research
SASTRA University, Thanjavur-613 401
Joint Initiative of IITs and IISc Funded by MHRD Page 1 of 8

Table of Contents
1. Rolling - Introductory concepts: ............................................ 3

1.1 Introduction ........................................................................................................................................ 3
1.2 Rolling mills: ........................................................................................................................................ 4
1.3 Grain structure in rolling: .................................................................................................................... 6
1.4 Special rolling processes: .................................................................................................................... 6

1. Rolling - Introductory concepts:
1.1 Introduction
Rolling is one of the most important industrial metal forming operations. Hot Rolling is
employed for breaking the ingots down into wrought products such as into blooms and billets,
which are subsequently rolled to other products like plates, sheets etc.
Rolling is the plastic deformation of materials caused by compressive force applied through a
set of rolls. The cross section of the work piece is reduced by the process. The material gets
squeezed between a pair of rolls, as a result of which the thickness gets reduced and the length
gets increased.
Mostly, rolling is done at high temperature, called hot rolling because of requirement of large
deformations. Hot rolling results in residual stress-free product. However, scaling is a major
problem, due to which dimensional accuracy is not maintained. Cold rolling of sheets, foils etc is
gaining importance, due to high accuracy and lack of oxide scaling. Cold rolling also strengthens
the product due to work hardening.
Steel ingot is the cast metal with porosity and blowholes. The ingot is soaked at the hot rolling
temperature of 1200oC and then rolled into blooms or billets or slabs.
Bloom is has a square cross section, with area more than 230 cm2. A slab, also from ingot, has
rectangular cross-section, with area of at least 100 cm2 and width at least three times the
thickness. A billet is rolled out of bloom, has at least 40 mm X 40 mm cross-section.
Blooms are used for rolling structural products such as I-sections, channels, rails etc. Billets are
rolled into bars, rods. Bars and rods are raw materials for extrusion, drawing, forging,
machining etc. Slabs are meant for rolling sheets, strips, plates etc.

Fig.1.1.1: Flow diagram showing Rolling of different products
Plates have thickness greater than 6 mm whereas strips and sheets have less than 6 mm
thickness.
Sheets have greater width and strip has lower width less than 600 mm.
1.2 Rolling mills:

Rolling mill consists of rolls, bearings to support the rolls, gear box, motor, speed control
devices, hydraulic systems etc. The basic type of rolling mill is two high rolling mill. In this mill,
two opposing rolls are used. The direction of rotation of the rolls can be changed in case of
reversing mills, so that the work can be fed into the rolls from either direction. Such mills
increase the productivity. Non reversing mills have rolls rotating in same direction. Therefore,
the work piece cannot be fed from the other side. Typical roll diameters may be 1.4 m.

A three high rolling mill has three rolls. First rolling in one direction takes place along one
direction. Next the work is reversed in direction and fed through the next pair of roll. This
improves the productivity.
Rolling power is directly proportional to roll diameter. Smaller dia rolls can therefore reduce
power input. Strength of small diameter rolls are poor. Therefore, rolls may bend. As a result,
largerdia backup rolls are used for supporting the smaller rolls. Four high rolling mill is one such
mill. Thin sections can be rolled using smaller diameter rolls. Cluster mill and Sendzimir mill are
used for rolling thin strips of high strength materials and foils [0.0025 mm thick]. The work roll
in these mills may be as small as 6 mm diameter made of tungsten carbide. Several rolling
mills arranged in succession so as to increase productivity is called rolling stand. In such
arrangement, anuncoiler and windup reels are used. They help in exerting back tension and
front tension.
Fig. 1.2.1: Rolling mills
Planetary mill has a pair of large heavy rolls, surrounded by a number of smaller rolls around
their circumference. In this mill, a slab can be reduced to strip directly in one pass. Feeder rolls
may be needed in order to feed the work piece into the rolls.
Merchant mill is specifically used for rolling bars.
Hot rolling is usually done with two high reversing mill in order to breakdown ingots into
blooms and billets. For increased productivity, universal mill has two vertical rolls which can
control the width of the work simultaneously.

Non ferrous materials are cold rolled into sheets from hot rolled strips. Four high tandem mills
are generally used for aluminium and copper alloys. In order to achieve upto 90% reduction in
thickness in cold rolling, a series of rolling mills may be used to share the total reduction.
One important application of cold rolling is the removal of yield point from mild steel sheets
using skin pass rolling [temper rolling]. In this the steel sheet is given a light reduction of 0.5 to
1.5% . Such a process eliminates yield point elongation. If yield elongation of steel occurs during
sheet metal operation, such as deep drawing, the surface of the sheet metal becomes rough
due to formation of Luder bands, also called stretcher strains.
Flatness of rolled sheets can be increased by roller leveling. In this process, the sheet is passed
between a pair of rolls which are driven by individual motors and are slightly offset.
Rolls should have high stiffness, hardness and strength. Cast iron, cast steel and forged steel are
also used as rolls.
1.3 Grain structure in rolling:

When the wrought or cast product gets hot rolled, the grain structure, which is coarse grained,
becomes finer in size, but elongated along the direction of rolling. This type of textured grain
structure results in directional property [anisotropy] for the rolled product. In order to refine
the grains, heat treatment is performed immediately after rolling, which results in
recrystallization after rolling.
Fig. 1.3.1: Variation of grain structure, size during longitudinal rolling
1.4 Special rolling processes:

Bulk deformation processes such as shape rolling, thread rolling, roll piercing, ring rolling also
use pair of rolls. Some of such important processes are discussed briefly below:
Thread and gear rolling:
Threads on cylindrical work pieces can be cold formed using a pair of flat dies or cylindrical rolls
under reciprocating or rotary motion. Screws, bolts and other externally threaded fasteners are
produced by thread rolling. Thread rolling is a high productivity process involving no loss of
material. Due to grain flow in thread rolling strength is increased. Surface finish of rolled
threads is very good. Gears can also be produced by the thread rolling process. Compressive
stresses introduced during the process isfavourable for fatigue applications. Auto power
transmission gears are made by thread rolling.
Shape rolling:
Structural sections such as I-sections, rails, channels can be rolled using set of shaped rolls.
Blooms are usually taken as raw materials for shape rolling. Multiple steps are required in
shape rolling.
Ring rolling:
Smaller diameter, thicker ring can be enlarged to larger diameter, thinner section by ring
rolling. In this process, two circular rolls, one of which is idler roll and the other is driven roll are
used. A pair of edging rollers are used for maintaining the height constant. The ring is rotated
and the rings are moved closer to each other, thereby reducing the thickness of ring and
increasing its diameter. Rings of different cross-sections can be produced. The major merits of
this process are high productivity, material saving, dimensional accuracy and grain flow which is
advantageous. Large rings for turbines, roller bearing races, flanges and rings for pipes are
some of the applications of this process.
Fig. 1.4.1: Ring rolling process
Tube piercing:
Rotary tube piercing is used for producing long thick walled tubes. Cavity forms at the center
due to tensile stress, in a round rod when subjected to external compressive stress especially
cyclic compressive stress.

Fig.1.4.2: Mannesmann Mill
The Mannesmann process makes use of a tube piercing in rotary mode. A pair of skewed rolls
are used for drawing the work piece inside the rolls. The roll axes are oriented at 6 degrees with
reference to axis of work piece. A mandrel is used for expanding the central hole, and sizing the
inner diameter. Pilger mill uses reciprocating motion of both work and mandrel to produce
tubes. Work is periodically rotated additionally.

Module 4 Lecture 1 Final PDF

Uploaded by

Copyright:

Available Formats

Module 4 Lecture 1 Final PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Module 4 Lecture 1 Final PDF

Uploaded by

Copyright:

Available Formats

NPTEL - Mechanical Engineering - Forming

Rolling - Introductory concepts

Joint Initiative of IITs and IISc Funded by MHRD Page 1 of 8

1. Rolling - Introductory concepts: ............................................ 3

Joint Initiative of IITs and IISc Funded by MHRD Page 2 of 8

1. Rolling - Introductory concepts:

Joint Initiative of IITs and IISc Funded by MHRD Page 3 of 8

Fig.1.1.1: Flow diagram showing Rolling of different products

1.2 Rolling mills:

Joint Initiative of IITs and IISc Funded by MHRD Page 4 of 8

Fig. 1.2.1: Rolling mills

Merchant mill is specifically used for rolling bars.

Joint Initiative of IITs and IISc Funded by MHRD Page 5 of 8

1.3 Grain structure in rolling:

Fig. 1.3.1: Variation of grain structure, size during longitudinal rolling

1.4 Special rolling processes:

Thread and gear rolling:

Fig. 1.4.1: Ring rolling process

Joint Initiative of IITs and IISc Funded by MHRD Page 7 of 8

Fig.1.4.2: Mannesmann Mill

Joint Initiative of IITs and IISc Funded by MHRD Page 8 of 8

You might also like