Third Angel Distortion Instruction Manual: This Pedal Is
Third Angel Distortion Instruction Manual: This Pedal Is
Third Angel Distortion Instruction Manual: This Pedal Is
Instruction Manual
May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047,
4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617.
Other patents pending. Foreign patents pending.
Compliance
Your Third Angel Distortion pedal has been tested and complies with the following
Standards and Directives as set forth by the European Union:
This means that this product has been designed to meet stringent guidelines on
how much RF energy it can emit, and that it should be immune from other sources
of interference when properly used. Improper use of this equipment could result
in increased RF emissions, which may or may not interfere with other electronic
products.
To insure against this possibility, always use good shielded cables for all audio input
and output connections. This will help insure compliance with the Directive(s).
For more information about other Rocktron products, please see your local dealer
or one of our importers closest to you (listed on the Rocktron website
(www.rocktron.com).
Refer all service to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus or if the apparatus has been exposed to rain
or moisture, does not operate normally or has been dropped.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat. This unit is designed to operate between 32 F and
104 F (0 C and 40 C). This unit may not function properly under extreme temperatures.
Do not block any ventilation openings (if applicable). Install in accordance with the
manufacturers instructions.
Do not install near any heat sources such as radiators, heat registers, stoves or other ap-
paratus (including amplifiers) that produce heat.
This product is not equipped with a plug or cable. This pedal runs on a 9 Volt Battery, if a
9Volt DC adapter is the used please follow adapter manufacturers operation instructions.
Only used attachments/accessories specified by the manufacturer.
Do not use this product with any case, stand tripod, bracket or table that is not specified by
the manufacturer. Insure that the case, stand, tripod, bracket etc. is properly adjusted and
setup (follow all instructions). Extra care and caution should be taken to avoid tip over
and injury.
Unplug this apparatus during lightening storms or when unused during long periods of time.
Introduction
THIRD ANGEL DISTORTION
Rocktron is well known for outrageous distortion tones, and the Third Angel
Distortion stomp box is no exception. Need it ultra heavy? If you seek heavy
screaming over-the-top distortion, this is your pedal!
Part of the Rocktron Boutique Series of stomp boxes this pedal design comes
in a rugged metal chassis with eye popping retro custom design laser etched
artwork. This is a TRUE BYPASS pedal: when you turn it offit is out of
your signal path!
Control knobs for the Third Angel Distortion include LEVEL which controls
the output volume of the box. BASS controls bass level, while TREBLE
controls the treble level settings. DECIEVE controls the amount of gain.
UNRIGHTEOUS controls the distortion waveform symmetry and definition.
The Third Angel is a fantastic choice to use with tube amps, and works great
with solid state amps too. This will provide you with an incredibly heavy
sound and mind-blowing tone!
Plug this awesome pedal in and rock the house, rock the club, rock the arena
with shockwaves of sound!
The footswitch on the Third Angel Distortion controls On/Off status (indi-
cated by the LED). This stomp box runs on a 9V Alkaline battery. You may
also use the Rocktron DC OnTap Universal Power Adaptor.
Descriptions
1 2 3 4
5
7
6
9 8
10
Descriptions continued.........
1 BASS Control - This control determines the low-end bass EQ.
3 9VDC Input - This input jack provides 9VDC power to the pedal from
the Rocktron DC OnTap 9V power supply (sold seperately).
5 ON/OFF Led - This LED shows if the pedal is on or off. When the
LED is light the pedal is on. When the LED is not light the pedal is
off.
8 INPUT Jack - Using a standard 1/4 guitar cable, plug your guitar into
this jack.
9 OUTPUT Jack - This jack provides the output of the pedal. Use a 1/4
guitar cable to plug into the next pedal or into a guitar amplifier.
10 FOOTSWITCH - Use this switch to turn on or off the pedal. The On/
Off Led will show you if the pedal is on or off.
Typical Connection
Specifications
Maximum Input 8dBu
Maximum Output 13Bu
Imput Impedance 1M
Output Impedance 2.8K
Current Consumption 15mA
Weight 410g
14.46 oz
www.rocktron.com
info@rocktron.com
tel: 1-269-968-3351
rev. 7-27-09
2009.1