Professional Documents
Culture Documents
Awwa d100 Potable
Awwa d100 Potable
PART 1. GENERAL
This section includes furnishing and erecting a ________ gallon welded steel reservoir
and necessary piping and appurtenances, per AWWA D100 specifications, latest
revision.
B. The bidder shall offer a new tank reservoir as supplied from a manufacturer
specializing in the design, fabrication and erection of welded water storage
tanks.
C. The tank shown on the contract drawings and specified herein shall be
fabricated by Tank Connection, ATEC Steel or approved equal.
1
project. The contractor shall be fully responsible for the entire
installation including appurtenances and the final product.
4. The components of the tank that come in contact with stored water
shall be certified to meet ANSI/NSF Additives Standard No. 61.
B. The bidder is required to furnish, for the approval of the Engineer and at no
increase in contract price, 5 sets of complete specifications and construction
drawings for all work not shown in complete detail on the bidding drawings. A
complete set of structural calculations shall be provided for the tank structure
and foundation.
C. When approved, two sets of such prints and submittal information will be
UHWXUQHGWRWKHELGGHUPDUNHG$33529(')25&216758&7,21 and
these drawings will then govern the work detailed thereon. The approval by
the EngiQHHURIWKHWDQNVXSSOLHUVGUDZLQJVVKDOOEHDQDSSURYDOUHODWLQJRQO\
to their general conformity with the bidding drawings and specifications and
shall not guarantee detail dimensions and quantities, which remains the
ELGGHUVUHVSRQVLELOLW\
A. The welded tank shall have a nominal diameter of _____ ft. with a nominal
sidewall height (to roof eave) of _____ ft.
2
2.03 TANK DESIGN REQUIREMENTS
A. The materials, design, fabrication and erection of the welded tank shall
conform to AWWA Standard D100, latest edition.
B. The welded steel reservoir will rest on an oiled sand base contained by a
concrete ring-wall foundation.
1. Inlet pipe
2. Overflow pipe
3. Outlet pipe
4. Drain pipe
5. 30" square, hinged, lockable roof hatch
6. Two shell manholes with hinged covers
7. Outside ladder with ladder gate and lock, without fall protection
8. Inside ladder without fall protection
9. Screened roof vent
10. Level indicator
11. Identification name plate
PART 3. MATERIALS
3.01 MANUFACTURERS
A. Furnish steel plate and structural shapes per AWWA D100, Section 2.
3
PART 4. COATINGS
A. All coatings that are in contact with potable water must be certified and on the
current approved list of the National Sanitation Foundation to meet ANSI/NSF
Additives Standard No. 61.
PART 5. FABRICATION
B. All exterior ladders, guard rails, brackets, hatch covers, pins and fasteners
shall be steel that is hot dipped galvanized per ASTM A123/153 after fabrication.
3. The dome and tank shall be designed to act as an integral unit. The
tank shall be designed to support an aluminum dome roof including all
specified live loads.
4
4. Materials
5.02 APPURTENANCES
A. Pipe Connections
2. Inlet and outlet connections shall conform to the sizes and locations
specified on the plan sheets.
B. Access Doors
5
C. Roof Vent
E. Roof Hatch
1. A liquid level indicator with stainless steel float, number board and high
visibility target shall be provided and installed as detailed on the project
drawings.
H. Identification Plate
1. 0DQXIDFWXUHUVQDPHSODWHVKDOOOLVWWKHWDQNVHULDOQXPEHUWDQN
diameter and height, and maximum design capacity. The nameplate
shall be affixed to the tank exterior sidewall location approximately five
(5) feet from the grade elevation.
6
PART 6. EXECUTION
6.01 EARTHWORK
6.02 CONCRETE
A. All concrete work for reservoir foundations and floor slabs shall be done
according to contract documents.
A. The tank fabricator shall field verify the foundation elevation and the
tolerances of the in-place foundation. Any deviations shall be reported to the
Engineer for correction before proceeding with any work. All tank piping must be
in place prior to the commencement of tank erection.
A. The CONTRACTOR shall furnish all labor, tools, scaffolding, and other
equipment necessary to properly erect the tank complete and ready for use.
A. After the erection of the reservoir is completed and before it is painted, it shall
be tested for leaks. Any leaks that are disclosed in the shell bottom, roof,
manhole, or piping shall be repaired prior to painting.
C. All defective welds shall be removed and repaired in accordance with Section
11 of AWWA D100, latest revision.
'0DNHDYDLODEOHDOOUDGLRJUDSKVDQGRWKHUWHVWLQJLQIRUPDWLRQWRWKH2ZQHUV
representative during construction.
7
E. After completion of the work, the Contractor shall submit a written report and
certification that all work has been inspected and tested and is in accordance
with all applicable provisions of AWWA D100, latest revision.
PART 7. DISINFECTION
7.01 STANDARDS
3$577$1.0$18)$&785(56:$55$17<
** END OF SECTION **