REACHSTACKER CONTAINER HANDLERS

RS 45-27 CH, RS 45-31 CH, RS 46-36 CH

RS 46-41L CH, RS 46-41S CH, RS 46-41LS CH

REACHSTACKER INTERMODAL HANDLERS

RS 45-24 IH, RS 45-28 IH, RS 46-33 IH
RS 46-38L IH, RS 46-38S IH, RS 46-38LS IH

STAGE IV
RS 45-27 CH - RS 46-41LS CH CONTAINER HANDLERS
1.1 Manufacturer (abbreviation)
HYSTER HYSTER HYSTER HYSTER HYSTER HYSTER
1.1
1.2 Manufacturers type designation RS 45-27 CH RS 45-31 CH RS 46-36 CH RS 46-41L CH RS 46-41S CH RS 46-41LS CH 1.2 NOTES:
1.3 Drive: electric (battery or mains), diesel, petrol, fuel gas Diesel Diesel Diesel Diesel Diesel Diesel 1.3 Specifications are affected by the condition of the vehicle and
1.4 Operator type: hand, pedestrian, standing, seated, orderpicker Seated Seated Seated Seated Seated Seated 1.4 how it is equipped, as well as the nature and condition of the
1.5.1 Load capacity at load centre distance c 1 Q1 ( t ) 45 45 46 46 46 46 1.5.1 operating area. Inform your dealer of the nature and condition of
DISTINGUISHING MARKS

DISTINGUISHING MARKS
1.5.2 Load capacity at load centre distance c 2 Q2 ( t ) 27 31 36 41 38 41 1.5.2 the intended operating area when purchasing your Hyster Truck.
1.5.3 Load capacity at load centre distance c 3 Q3 ( t ) 13 16 19 23 21 23 1.5.3 u From face of front tyres. Deduct 100 mm for loadcentre from
1.5.1.s Load capacity at loadcenter c 1 (stabilizer applied) Q1 ( t ) - - - - 46 46 1.5.1.s front side of Stabilizer when applicable
1.5.2.s Load capacity at loadcenter c 2 (stabilizer applied) Q2 ( t ) - - - - 41 41 1.5.2.s
l For CH models only: With optional PPS (Powered Pile Slope)
1.5.3.s Load capacity at loadcenter c 3 (stabilizer applied) Q3 ( t ) - - - - 28 30 1.5.3.s function: deduct 310 mm
1.6.1 Load centre distance 1 u c1 (mm) 1,865 1,865 1,865 1,865 1,865 1,865 1.6.1
Full suspension seat in depressed position
1.6.2 Load centre distance 2 u c2 (mm) 3,815 3,815 3,815 3,815 3,815 3,815 1.6.2
1.6.3 Load centre distance 3 u c3 (mm) 6,315 6,315 6,315 6,315 6,315 6,315 1.6.3 s Spreader at 8.0 m high, central above front axle

1.8 Load distance, centre of drive axle to face of front tyres / front of Stabilizer x (mm) 835 / NA 835 / NA 930 / NA 930 / NA 930 / 1030 930 / 1030 1.8 v These data are with the container carried 500 mm in front of
1.9 Wheelbase y (mm) 6,200 6,200 6,200 6,700 6,200 6,700 1.9 the wheels (load centre 1720 mm)
1.10 Stacking height at first row (number x container height, in feet) 5 x 9 6 5 x 9 6 5 x 9 6 5 x 9 6 5 x 9 6 5 x 9 6 1.10 Stacking aisle width is based on the VDI standard calculation
as shown on illustration. The British Industrial Truck
2.1 Service weight kg 68,500 72,200 79,300 82,600 83,600 84,600 2.1 Association recommends the addition of 100 mm to the total
2.2.1 Axle loading, laden front / rear at c 1 kg 99,900 13,600 99,600 17,600 103,200 22,100 103,400 25,200 105,400 24,200 105,600 25,000 2.2.1 clearance (dimension a) for extra operating margin at the rear

WEIGHTS
WEIGHTS

2.2.2 Axle loading, laden front / rear at c 2 kg 87,800 7,700 94,500 8,700 105,300 10,000 113,100 10,500 111,900 10,200 115,300 10,300 2.2.2 of truck.
2.3.1 Axle loading, unladen front / rear at c 1 kg 35,300 33,200 35,000 37,200 36,500 42,800 38,200 44,400 38,700 44,900 40,400 44,200 2.3.1 ] T
 ravel speed laden/unladen limited at 25 km/h
2.3.2 Axle loading, unladen front / rear at c 2 kg 40,500 28,000 40,300 31,900 41,700 37,600 43,000 39,600 43,900 39,700 45,300 39,300 2.3.2 as factory default.
w First row average, laden (35 ton) / unladen
3.1 Tyres: L = pneumatic, V = solid, SE = pneumatic-shaped solid L L L L L L 3.1
at 1,6 km/h. Gradeability figures are provided for comparison
TYRES / CHASSIS

TYRES / CHASSIS
3.2 Tyres size, front 18.00 x 25 18.00 x 25 18.00 x 33 18.00 x 33 18.00 x 33 18.00 x 33 3.2
of tractive performance, but are not intended to endorse the
3.3 Tyres size, rear 18.00 x 25 18.00 x 25 18.00 x 33 18.00 x 33 18.00 x 33 18.00 x 33 3.3
operation of vehicle on the stated inclines.
3.5 Wheels, number front/rear (X = driven wheels) x 4 / 2 x 4 / 2 x4 / 2 x 4 / 2 x 4 / 2 x 4 / 2 3.5
3.6 Tread, front mm 3,703 3,703 3,703 3,703 3,703 3,703 3.6 J without additional fan in HIP mode 71.3 db(A)

3.7 Tread, rear mm 3,060 3,060 3,060 3,060 3,060 3,060 3.7 without additional fan in ECO-eLo mode 70.7 db(A

4.1 Boom angle minimum / maximum degrees () 0 59 0 59 0 59 0 59 0 59 0 59 4.1

All capacities are according to EN1459
4.2 Height, boom lowered h1 (mm) 4,700 4,700 4,795 4,795 4,795 4,795 4.2
All specifications and capacities are valid for trucks equipped with
4.4.1 Lift height at load centre c 1 l h3.1.1 (mm) 15,260 15,260 15,355 15,355 15,355 15,355 4.4.1
a Hyster container handling spreader for handling ISO containers.
4.4.2 Lift height at load centre c 2 l h3.1.2 (mm) 13,850 13,850 13,945 13,945 13,945 13,945 4.4.2
4.5 Height, boom extended h4 (mm) 18,110 18,110 18,205 18,205 18,205 18,205 4.5
4.7 Height of overhead guard (cabin) h6 (mm) 3,720 3,720 3,815 3,815 3,815 3,815 4.7
4.8 Seat height relating to SIP h7 (mm) 2,555 2,555 2,650 2,650 2,650 2,650 4.8
4.15 Height, lowered l h13 (mm) 1,345 1,345 1,440 1,440 1,440 1,440 4.15
4.19 Overall length l1 (mm) 8,360 8,360 8,650 9,150 8,750 9,250 4.19
4.20 Overall length including boom retracted l2 (mm) 11,873 11,873 12,073 12,573 12,073 12,573 4.20
4.21.2 Overall width across all b2 (mm) 4,200 4,200 4,200 4,200 4,200 4,200 4.21.2
DIMENSIONS

DIMENSIONS
4.21.3 Overall width across spreader 20 b1.20 (mm) 6,100 6,100 6,100 6,100 6,100 6,100 4.21.3
4.21.4 Overall width across spreader 40 b1.40 (mm) 12,200 12,200 12,200 12,200 12,200 12,200 4.21.4
4.31 Ground clearance lowest point m1 (mm) 285 285 304 304 250 250 4.31
4.32 Ground clearance, centre of wheelbase m2 (mm) 437 437 532 532 532 532 4.32
4.34.3.1 Aisle width with 20 container without operating clearance s Ast 20 (mm) 9,817 9,817 9,977 10,477 9,977 10,477 4.34.3.1
4.34.3.2 Aisle width with 20 container without operating clearance v Ast 20 (mm) 12,439 12,439 12,608 12,608 12,608 12,608 4.34.3.2
4.34.3.3 Aisle width with 20 container with 200 mm operating clearance v Ast 20 (mm) 12,639 12,639 12,808 12,808 12,808 12,808 4.34.3.3
4.34.3.4 Aisle width with 20 container with 10% operating clearance v Ast 20 (mm) 13,683 13,683 13,869 13,869 13,869 13,869 4.34.3.4
4.34.4.1 Aisle width with 40 container without operating clearance s Ast 40 (mm) 12,569 12,569 12,569 12,569 12,569 12,569 4.34.4.1
4.34.4.2 Aisle width with 40 container without operating clearance v Ast 40 (mm) 14,203 14,203 14,203 14,203 14,203 14,203 4.34.4.2
4.34.4.3 Aisle width with 40 container with 200 mm operating clearance v Ast 40 (mm) 14,403 14,403 14,403 14,403 14,403 14,403 4.34.4.3
4.34.4.4 Aisle width with 40 container with 10% operating clearance v Ast 40 (mm) 15,623 15,623 15,623 15,623 15,623 15,623 4.34.4.4
4.35 Turning radius Wa (mm) 8,495 8,495 8,562 9,062 8,562 9,062 4.35
4.36 Internal turning radius b13 (mm) 2,690 2,690 2,690 2,690 2,690 2,690 4.36
NOTICE:
Care must be exercised when handling elevated loads. When
5.1 Travel speed, laden/unladen ] km/h 20 22 20 22 21 23 21 23 21 23 21 23 5.1

PERFORMANCE DFATA
the carriage and/or load is elevated, truck stability is reduced. It is
PERFORMANCE DATA

5.2 Lift speed, laden/unladen w m/s 0.28 0.48 0.28 0.48 0.28 0.48 0.28 0.48 0.28 0.48 0.28 0.48 5.2 important that the mast tilt in either direction is kept to a minimum
5.3 Lowering speed laden / unladen m/s 0.46 0.45 0.46 0.45 0.46 0.45 0.46 0.45 0.46 0.45 0.46 0.45 5.3 when loads are elevated.
5.7 Gradeability laden/unladen % 26 25 23 21 21 21 5.7 Operators must be trained and must read, understand and follow
5.9 Acceleration time, laden/unladen sec On Request On Request On Request On Request On Request On Request 5.9 the instructions contained in the Operating Manual.
5.10 Service brake Oil-immersed disc Oil-immersed disc Oil-immersed disc Oil-immersed disc Oil-immersed disc Oil-immersed disc 5.10 All values are nominal values and they are subject to tolerances.
For further information, please contact the manufacturer.
10.1 Operating presure for attachments mPa 14.0 14.0 14.0 14.0 14.0 14.0 10.1 Hyster products are subject to change without notice.
10.2 Oil volume for attachements l/min 110 110 110 110 110 110 10.2
Lift trucks illustrated may feature optional equipment. Values may

ADDITIONAL DATA
ADDITIONAL DATA

10.3 Hydraulic oil tank, capacity l 625 625 625 625 625 625 10.3 vary with alternative configurations.
10.4 Fuel tank, capacity l 830 830 830 830 830 830 10.4
10.4.1 DEF tank, capacity l 57 57 57 57 57 57 10.4.1
Safety: This truck conforms to the current
10.5 Steering design Hydrostatic Hydrostatic Hydrostatic Hydrostatic Hydrostatic Hydrostatic 10.5 EU requirements.
10.7 Sound pressure level at the drivers seat LPAZ J dB(A) 73.9 73.9 73.9 73.9 73.9 73.9 10.7
10.7.1 Sound power level during the workcycle LWAZ dB(A) On Request On Request On Request On Request On Request On Request 10.7.1

Specification data is based on VDI 2198

2 3
RS 45-24 IH - RS 46-38LS IH INTERMODAL HANDLERS
1.1 Manufacturer (abbreviation)
HYSTER HYSTER HYSTER HYSTER HYSTER HYSTER
1.1
1.2 Manufacturers type designation RS 45-24 IH RS 45-28 IH RS 46-33 IH RS 46-38L IH RS 46-38S IH RS 46-38LS IH 1.2 NOTES:
1.3 Drive: electric (battery or mains), diesel, petrol, fuel gas Diesel Diesel Diesel Diesel Diesel Diesel 1.3 Specifications are affected by the condition of the vehicle and
1.4 Operator type: hand, pedestrian, standing, seated, orderpicker Seated Seated Seated Seated Seated Seated 1.4 how it is equipped, as well as the nature and condition of the
1.5.1 Load capacity at load centre distance c 1 Q1 ( t ) 45 45 46 46 46 46 1.5.1 operating area. Inform your dealer of the nature and condition of
DISTINGUISHING MARKS

DISTINGUISHING MARKS
1.5.2 Load capacity at load centre distance c 2 Q2 ( t ) 24 28 33 38 35 38 1.5.2 the intended operating area when purchasing your Hyster Truck.
1.5.3 Load capacity at load centre distance c 3 Q3 ( t ) 11 13 17 20 18 20 1.5.3 u From face of front tyres. Deduct 100 mm for loadcentre from
1.5.1.s Load capacity at loadcenter c 1 (stabilizer applied) Q1 ( t ) - - - - 46 46 1.5.1.s front side of Stabilizer when applicable
1.5.2.s Load capacity at loadcenter c 2 (stabilizer applied) Q2 ( t ) - - - - 38 38 1.5.2.s
l For CH models only: With optional PPS (Powered Pile Slope)
1.5.3.s Load capacity at loadcenter c 3 (stabilizer applied) Q3 ( t ) - - - - 25 27 1.5.3.s function: deduct 310 mm
1.6.1 Load centre distance 1 u c1 (mm) 1,865 1,865 1,865 1,865 1,865 1,865 1.6.1
Full suspension seat in depressed position
1.6.2 Load centre distance 2 u c2 (mm) 3,815 3,815 3,815 3,815 3,815 3,815 1.6.2
1.6.3 Load centre distance 3 u c3 (mm) 6,315 6,315 6,315 6,315 6,315 6,315 1.6.3 s Spreader at 8.0 m high, central above front axle

1.8 Load distance, centre of drive axle to face of front tyres / front of Stabilizer x (mm) 835 / NA 835 / NA 930 / NA 930 / NA 930 / 1030 930 / 1030 1.8 v These data are with the container carried 500 mm in front of
1.9 Wheelbase y (mm) 6,200 6,200 6,200 6,700 6,200 6,700 1.9 the wheels (load centre 1720 mm)
1.10 Stacking height at first row (number x container height, in feet) 5 x 9 6 5 x 9 6 5 x 9 6 5 x 9 6 5 x 9 6 5 x 9 6 1.10 Stacking aisle width is based on the VDI standard calculation
as shown on illustration. The British Industrial Truck
2.1 Service weight kg 72,400 76,100 83,200 86,500 87,500 88,500 2.1 Association recommends the addition of 100 mm to the total
2.2.1 Axle loading, laden front / rear at c 1 kg 105,400 12,000 105,200 15,900 108,800 20,400 108,800 23,700 111,000 22,500 111,000 23,500 2.2.1 clearance (dimension a) for extra operating margin at the rear

WEIGHTS
WEIGHTS

2.2.2 Axle loading, laden front / rear at c 2 kg 89,300 7,100 96,000 8,100 106,800 9,400 114,500 10,000 112,500 10,000 116,700 9,800 2.2.2 of truck.
2.3.1 Axle loading, unladen front / rear at c 1 kg 40,800 31,600 40,500 35,600 42,100 41,100 43,600 42,900 44,200 43,300 45,800 42,700 2.3.1 ] T
 ravel speed laden/unladen limited at 25 km/h
2.3.2 Axle loading, unladen front / rear at c 2 kg 47,300 25,100 47,000 29,100 48,600 34,600 49,600 36,900 50,700 36,800 51,900 36,600 2.3.2 as factory default.
w First row average, laden (35 ton) / unladen
3.1 Tyres: L = pneumatic, V = solid, SE = pneumatic-shaped solid L L L L L L 3.1
at 1,6 km/h. Gradeability figures are provided for comparison
TYRES / CHASSIS

TYRES / CHASSIS
3.2 Tyres size, front 18.00 x 25 18.00 x 25 18.00 x 33 18.00 x 33 18.00 x 33 18.00 x 33 3.2
of tractive performance, but are not intended to endorse the
3.3 Tyres size, rear 18.00 x 25 18.00 x 25 18.00 x 33 18.00 x 33 18.00 x 33 18.00 x 33 3.3
operation of vehicle on the stated inclines.
3.5 Wheels, number front/rear (X = driven wheels) x 4 / 2 x 4 / 2 x4 / 2 x 4 / 2 x 4 / 2 x 4 / 2 3.5
3.6 Tread, front mm 3,703 3,703 3,703 3,703 3,703 3,703 3.6 J without additional fan in HIP mode 71.3 db(A)

3.7 Tread, rear mm 3,060 3,060 3,060 3,060 3,060 3,060 3.7 without additional fan in ECO-eLo mode 70.7 db(A
n Side shift
4.1 Boom angle minimum / maximum degrees () 0 59 0 59 0 59 0 59 0 59 0 59 4.1
4.2 Height, boom lowered h1 (mm) 4,700 4,700 4,795 4,795 4,795 4,795 4.2
All capacities are according to EN1459
4.4.1 Lift height at load centre c 1 l h3.1.2 (mm) 14,780 14,780 14,875 14,875 14,875 14,875 4.4.1
4.4.2 Lift height at load centre c 2 l h3.1.2 (mm) 13,375 13,375 13,470 13,470 13,470 13,470 4.4.2 All specifications and capacities are valid for trucks equipped with
a Hyster container handling spreader for handling ISO containers.
4.5 Height, boom extended h4 (mm) 18,110 18,110 18,205 18,205 18,205 18,205 4.5
4.7 Height of overhead guard (cabin) h6 (mm) 3,720 3,720 3,815 3,815 3,815 3,815 4.7
4.8 Seat height relating to SIP h7 (mm) 2,555 2,555 2,650 2,650 2,650 2,650 4.8
4.15 Height, lowered l h13 (mm) 885 885 980 980 980 980 4.15
4.19 Overall length l1 (mm) 8,360 8,360 8,650 9,150 8,750 9,250 4.19
4.20 Overall length including boom retracted l2 (mm) 11,873 11,873 12,073 12,573 12,073 12,573 4.20
4.21.2 Overall width across all b2 (mm) 4,200 4,200 4,200 4,200 4,200 4,200 4.21.2
DIMENSIONS

DIMENSIONS
4.21.3 Overall width across spreader 20 b1.20 (mm) 6,100 6,100 6,100 6,100 6,100 6,100 4.21.3
4.21.4 Overall width across spreader 40 b1.40 (mm) 12,200 12,200 12,200 12,200 12,200 12,200 4.21.4
4.31 Ground clearance lowest point m1 (mm) 285 285 304 304 250 250 4.31
4.32 Ground clearance, centre of wheelbase m2 (mm) 437 437 532 532 532 532 4.32
4.34.3.1 Aisle width with 20 container without operating clearance s Ast 20 (mm) 9,817 9,817 9,977 10,477 9,977 10,477 4.34.3.1
4.34.3.2 Aisle width with 20 container without operating clearance v Ast 20 (mm) 12,439 12,439 12,608 12,608 12,608 12,608 4.34.3.2
4.34.3.3 Aisle width with 20 container with 200 mm operating clearance v Ast 20 (mm) 12,639 12,639 12,808 12,808 12,808 12,808 4.34.3.3
4.34.3.4 Aisle width with 20 container with 10% operating clearance v Ast 20 (mm) 13,683 13,683 13,869 13,869 13,869 13,869 4.34.3.4
4.34.4.1 Aisle width with 40 container without operating clearance s Ast 40 (mm) 12,569 12,569 12,569 12,569 12,569 12,569 4.34.4.1
4.34.4.2 Aisle width with 40 container without operating clearance v Ast 40 (mm) 14,203 14,203 14,203 14,203 14,203 14,203 4.34.4.2
4.34.4.3 Aisle width with 40 container with 200 mm operating clearance v Ast 40 (mm) 14,403 14,403 14,403 14,403 14,403 14,403 4.34.4.3
4.34.4.4 Aisle width with 40 container with 10% operating clearance v Ast 40 (mm) 15,623 15,623 15,623 15,623 15,623 15,623 4.34.4.4
4.35 Turning radius Wa (mm) 8,495 8,495 8,562 9,173 8,562 9,173 4.35
4.36 Internal turning radius b13 (mm) 2,690 2,690 2,690 2,690 2,690 2,690 4.36
NOTICE:
Care must be exercised when handling elevated loads. When
5.1 Travel speed, laden/unladen ] km/h 20 22 20 22 21 23 21 23 21 23 21 23 5.1 the carriage and/or load is elevated, truck stability is reduced. It is

PERFORMANCE DFATA
PERFORMANCE DATA

5.2 Lift speed, laden/unladen w m/s 0.28 0.48 0.27 0.47 0.27 0.47 0.27 0.47 0.27 0.47 0.27 0.47 5.2 important that the mast tilt in either direction is kept to a minimum
5.3 Lowering speed laden / unladen m/s 0.46 0.45 0.46 0.45 0.46 0.45 0.46 0.45 0.46 0.45 0.46 0.45 5.3 when loads are elevated.
5.7 Gradeability laden/unladen % 22 22 22 22 22 22 5.7 Operators must be trained and must read, understand and follow
5.9 Acceleration time, laden/unladen sec On Request On Request On Request On Request On Request On Request 5.9 the instructions contained in the Operating Manual.
5.10 Service brake Oil-immersed disc Oil-immersed disc Oil-immersed disc Oil-immersed disc Oil-immersed disc Oil-immersed disc 5.10 All values are nominal values and they are subject to tolerances.
For further information, please contact the manufacturer.

10.1 Operating presure for attachements MPa 14.0 14.0 14.0 14.0 14.0 14.0 10.1 Hyster products are subject to change without notice.
10.2 Oil volume for attachements l/min 110 110 110 110 110 110 10.2 Lift trucks illustrated may feature optional equipment. Values may
vary with alternative configurations.

ADDITIONAL DATA
ADDITIONAL DATA

10.3 Hydraulic oil tank, capacity l 625 625 625 625 625 625 10.3
10.4 Fuel tank, capacity l 830 830 830 830 830 830 10.4
10.4.1 DEF tank, capacity l 57 57 57 57 57 57 10.4.1 Safety: This truck conforms to the current EU
10.5 Steering design Hydrostatic Hydrostatic Hydrostatic Hydrostatic Hydrostatic Hydrostatic 10.5 requirements.
10.7 Sound pressure level at the drivers seat LPAZ J dB(A) 73.9 73.9 73.9 73.9 73.9 73.9 10.7
10.7.1 Sound power level during the workcycle LWAZ dB(A) On Request On Request On Request On Request On Request On Request 10.7.1

Specification data is based on VDI 2198

4 5
POWERTRAINS TRUCK DIMENSIONS
1.1 Manufacturer (abbreviation) HYSTER HYSTER
DESIGNATION

1.2 Manufacturers type designation RS CH RS IH

1.3 Drive: electric (battery or mains), diesel, petrol, fuel gas Diesel Diesel

7.1 Engine manufacturer / type Stage IV Cummins QSL9 Cummins QSL9

a
7.2 Engine power according to ISO 1585 Stage IV kW @ RPM 261 @ 2100 261 @ 2100
POWER UNIT

7.2.1 Max. engine power according to ISO 1585 Stage IV kW @ RPM 283 @ 1900 283 @ 1900
7.3 Rated speed min1 2,100 2,100
7.3.1 Torque at 1/min Stage IV Nm/min1 1627 @ 1500 1627 @ 1500
7.4 Number of cylinders / displacement Stage IV (-) / cm3 6 / 8900 6 / 8900
7.5.1 Fuel consumtion according to VDI cycle l/h On Request On Request

r1
8.1 Type of drive unit Torque Converter Torque Converter
DRIVE TRAIN

8.2.1 Transmission manufacturer / type Spicer Off-Highway / TE-32 Spicer Off-Highway / TE-32
8.6 Wheel drive / drive axle manufacturer/type Kessler / D102PL341/528-NLB Kessler / D102PL341/528-NLB
8.11 Service brake Oil immersed disc Oil immersed disc
8.12 Parking brake Dry disc on drive axle Dry disc on drive axle

9.1 Manufacturer / type Elme / 817 Elme / 857

9.1.1 Pile slope spreader, mechanical without PPS 3 3
9.1.2 Pile slope spreader, mechanical with PPS 1.5 1,5
SPREADER

9.1.3 Pile slope spreader, Power Pile Slope 6 6

9.3 Size of containers feet () ISO 20 - 40 ISO 20 - 40
9.4 Side thrust n b8 (mm) 800 / 800 800 / 800
9.6.1 Rotation angle, without override +12 / -12 +12 / -12
9.6.2 Rotation angle, with override +185 / -95 +185 / -95
Ast V

TRUCK DIMENSIONS

Wa
r2
r1 = radius of swing of container rear corner
r2 = radius of swing of container front corner
Wa = outside turning radius of the truck
a = total operating clearance:
= 200 mm (100 mm each side acc. VDI) see VDI line 4.34.3
= 10% of V (acc. FEM TN01 recommendation) see VDI line 4.34.4
a is operating clearance at each side
V = (theoretical) 90 ~ stacking aisle width, no intrusive stacking:
V = r2 + the larger of r1 or Wa

a Ast = (practical) 90 ~ stacking aisle width, no intrusive stacking and with

clearance:
Ast = V + a

h4

h3.1.2

h1

h6
b8
b2

Q h7 b1.20 b10 b11

46-4ILS CH b8
h3.1.1

b13

m1 m1 m2
c x y
l1

l2

6 7
RATED CAPACITIES AND STACKING HEIGHTS CONTAINER HANDLERS RATED CAPACITIES AND STACKING HEIGHTS INTERMODAL HANDLERS

RS 4527 CH CONTAINER SPREADER RS 4641L CH CONTAINER SPREADER RS 4524 IH INTERMODAL SPREADER RS 4638S IH INTERMODAL SPREADER

Stabilizer NOT applied

39 39
24 43 33 43
43 24 45 35 46
27 43 43 24 45 h4 35 46 h4
36 46
27 45 10 24 45 18 35 46 18 35
h4 10 24 45 46
13 27 45 40 46
23 41 46 h4 18 35 46
10 24 45 10 24 45 18 35 46
13 27 45 13 27 45 23 41 46 11 24 45 18 35 46
23 41 46 45-24 IH 10 24 45 10 24 45 45-24 IH 46-38S IH 18 35 46 18 35 46 46-38S IH

13 27 45 13 27 45
23 41 46 23 41 46 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1

13 27 45 13 27 45 45-27 CH

23 41 46 23 41 46 46-41L CH swap-bodies and containers 9 6 containers 8 6 containers swap-bodies and containers 9 6 containers 8 6 containers
c3 c2 c1 c3 c2 c1
c3 c2 c1 c3 c2 c1
9 6 containers 8 6 containers 9 6 containers 8 6 containers Stabilizer applied (truck static) 39
RS 4528 IH INTERMODAL SPREADER 33 43
36 46
38 46 h4
25 38 46 25 38
39 46
RS 4531 CH CONTAINER SPREADER RS 4641S CH CONTAINER SPREADER 28 43
25 38 46 25 38 46
28 45
28 45 h4 25 38 46
46-38S IH 25 38 46 25 38 46 46-38S IH

13 28 45 13
Stabilizer applied (truck static) Stabilizer NOT applied 28 45
c3 c2 c1 c3 c2 c1 c3 c2 c1
13 28 45 13 28 45
43 43 43
45
31 43 36 46 36 46 13 28 swap-bodies and containers 9 6 containers 8 6 containers
45-28 IH 13 28 45 13 28 45 45-28 IH

31 45 40 46 38 46 Note: All load centres c1, c2, c3 are taken from the front face of the (front) tyres,
16 31 45 h4 28 41 46 21 38 46 h4 c3 c2 c1 c3 c2 c1 c3 c2 c1 deduct 100mm for load centres taken from the front face of the Stabilizer.

16 31 45 28 41 46 21 38 46
16 31 45 28 41 46 21 38 46 swap-bodies and containers 9 6 containers 8 6 containers

16 31 45 16 31 45 28 41 46 28 41 46 21 38 46 21 38 46

16 31 45 16 31 45 45-31 CH 28 41 46 28 41 46 21 38 46 21 38 46 46-41S CH

c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 RS 4633 IH INTERMODAL SPREADER RS 4638LS IH INTERMODAL SPREADER

9 6 containers 8 6 containers 9 6 containers 8 6 containers 9 6 containers 8 6 containers

Stabilizer NOT applied
Note: All load centres c1, c2, c3 are taken from the front face of the (front) tyres, 39 39
deduct 100mm for load centres taken from the front face of the Stabilizer. 33 43 33 43
33 46 36 46
33 46 h4 38 46 h4
16 33 46 16 33 20 38 46
46 20 38 46
RS 4636 CH CONTAINER SPREADER RS 4641LS CH CONTAINER SPREADER
16 33 46 16 33 46 20 38 46 20 38 46
17 33 46 20 38 46
46-33 IH 16 33 46 16 33 46 46-33 IH 46-38LS IH 20 38 46 20 38 46 46-38LS IH

Stabilizer applied (truck static) Stabilizer NOT applied

c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1
43 43 43
36 43 36 46 36 46 swap-bodies and containers 9 6 containers 8 6 containers swap-bodies and containers 9 6 containers 8 6 containers
36 46 40 46 40 46
19 36 46 h4 29 41 46 23 41 46 h4
19 36 46 19 36 46 30 41 46 23 41 46
30 41 46 23 41 46 Stabilizer applied (truck static)
39
RS 4638L IH INTERMODAL SPREADER 33 43
19 36 46 19 36 46 30 41 46 30 41 46 23 41 46 23 41 46 36 46 h4
38 46
19 36 46 19 36 46 46-36 CH
30 41 46 30 41 46 23 41 46 23 41 46 27 38 46 27 38
46-41LS CH

39 46
33 43
c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 c3 c2 c1 27 38 46 27 38 46
36 46
38 46 h4 27 46
38
46 27 38 46 27 38 46
9 6 containers 8 6 containers 9 6 containers 8 6 containers 9 6 containers 8 6 containers 20 38
46-38LS IH 46-38LS IH

20 38 46
c3 c2 c1 c3 c2 c1 c3 c2 c1
Note: All load centres c1, c2, c3 are taken from the front face of the (front) tyres, 20 38 46 20 38 46
deduct 100mm for load centres taken from the front face of the Stabilizer. 20 46
38
46-38L IH 20 38 46 20 38 46 46-38L IH
swap-bodies and containers 9 6 containers 8 6 containers

c3 c2 c1 c3 c2 c1 c3 c2 c1 Note: All load centres c1, c2, c3 are taken from the front face of the (front) tyres,
deduct 100mm for load centres taken from the front face of the Stabilizer.

swap-bodies and containers 9 6 containers 8 6 containers

NOTE: Care must be exercised when handling elevated loads. NOTE: Care must be exercised when handling elevated loads.
When the load is elevated, truck stability is reduced. When the load is elevated, truck stability is reduced.

8 9
 FRONT END EQUIPMENT Interior Wide Angle Mirrors
E  xternal Wide Angle Mirrors
Rear: 2 Rear Mounted
Halogen Lights
n Literature Package
Operators Manual
Mounted on Front Fenders 2 Stop/Tail/Backup Lights n Warranty
Operator Presence System Turn Signal & Hazard Lights 12 Months / 2,000 Hours
n Lockable Battery Disconnect Switch Spreader: 2 Halogen Work Lights Manufacturers Warranty
n 24 V Electrical System on Spreader
n 120 amp Alternator n Visible Alarm Amber Strobe Light
n Lifting Eyes to Hoist Complete Truck Key switch Activated
n Light Kit 1, consisting of: n Audible Alarm Reverse Direction

Front: 4 Halogen Work Lights, Activated 82102 dB(A)

Fender Mounted Self adjusting
2 Marker Lights n Non-Locking Fuel Cap

4 Halogen Lights Boom Mounted

20-40 telescopic ISO top pick spreader with mechanical pile slope 20-40 telescopic ISO top pick spreader with powered pile slope
OPTIONAL EQUIPMENT: n Seat Options: n Light Kit 4 with staircase and engine
n DANA Spicer Off-Highway TE-27 4 Pneumatic, Full Suspension cloth compartment lights, consisting of:
Speed Auto-shifting transmission seat with integrated adjustable Front: 4 HID Work Lights Fender
n Engine pre-heater 230 V (AC) armrest, high backrest, head rest Mounted
and seatbelt 2 Marker Lights
n NATO plug Start aid
Deluxe air suspended seat with 4 Halogen Lights Boom Mounted
n 24V heated diesel filter
adjustable shock absorber forward Rear: 2 Rear Mounted Halogen
n Spreader Options: and backward motion +/- 25 mm, Lights
Powered Pile Slope on CH cushion 21; 150 mm higher
2 Stop/Tail/Backup Lights
Powered Dampening on CH backrest, head rest and 3-points
high visibility seatbelt Turn Signal & Hazard Lights
4 Lifting Eyes Located Under
Center Beam of Spreader Heated Deluxe air suspended seat Spreader: 1 HID Work Lights on
Spreader
n Tire Options Drive and Steer: n 3B6 Load Moment Indicator with
colour display n Traction Speed Limiter factory
18.00 25 40PR STMS slick
pre-set to 16 km/h or 20 km/h
20-40 telescopic spreader with powered pile slope and foldable 20-40 telescopic spreader with powered pile slope and foldable 18.00 R25 Radial slick n Light Kit 2, consisting of:
Piggy back legs in Piggy back legs out n Automatic Engine Shutdown
18.00 R33 Radial slick Front: 4 HID Work Lights Fender
Mounted n Auto Greasing System
n Vista cab options:
2 Marker Lights Basic Truck / Outer Boom

STANDARD AND OPTIONAL EQUIPMENT

Air conditioning with sun shades
4 Halogen Lights Boom Mounted Spreader / Inner Boom
on top and rear
Rear: 2 Rear Mounted n Hyster Tracker Wireless Asset
Temperature controlled air
Halogen Lights Management system
conditioning with sun shades on
STANDARD EQUIPMENT: n Integrated IH Spreader, ELME Model Isolated Mounting for Low Noise and
2 Stop/Tail/Backup Lights
top and rear
n Cummins QSL 9L 261 / max. 283 KW 857 with Powered Pile Slope and Vibration
High performance temperature Turn Signal & Hazard Lights Other options available through
@ 1.900 rpm Turbo Diesel Engine Powered dampening for Handrails for Operator Entry and Exit
controlled air conditioning with Special Products Engineering
Stage IV Compliant Intermodal Handlers (Left Side) Spreader: 1 HID Work Lights
sun shades on top and rear Development (SPED).
n Wet Disc Brakes Steering Wheel Spinner Knob on Spreader
ECO-eLo / HiP performance modes Contact Hyster for details.
n Kessler D102 PL 341/528 NLB Air Compressor Horn 2.600 mm sliding cab with extra n Light Kit 3 with staircase and engine
Hibernate Idle
Drive Axle Heater with 3 speed fan cab access exit in the fully compartment lights, consisting of:
Hydraulically driven cooling fan
n Steer Axle with Tyre Life forward position on CH Front: 4 Halogen Work Lights
n DANA Spicer Off-Highway TE-32 4 Front and rear window defrosters
Enhancement System H-type double Front screen wiper Sun rollo on top and rear windows Fender Mounted
Speed Auto-shifting transmission
n Power-on-Demand Load Sensing Top and Rear Wipers Trainers seat 2 Marker Lights
n Automatic rev-up function when
lifting: Hydraulic System featuring Variable Recirculation Fan IT equipment bar 4 Halogen Lights Boom Mounted
Displacement Pump Technology 3B6 Load Moment Indicator with
If not in gear or when the inching Rear locking console Rear: 2 Rear Mounted
n Directional Control Lever Monochrome Display
pedal is depressed, the engine Heated top window Halogen Lights
automatically revs up, (up to 1800 n Tyres Drive and Steer 3B6 Load Moment Indicator with Audio system set-up (wiring, two 2 Stop/Tail/Backup Lights
rpm) when lifting 18.00 25 40PR Standard pneumatic colour Display for S models speakers and antenna) Turn Signal & Hazard Lights
When in gear, the auto-rev-up 18.00 33 36PR Standard pneumatic Mechanical, Full Suspension Cloth
Front screen with single wiper Spreader: 2 Halogen Work Lights
function is disengaged n Steer Wheel Nut Protection Seat with integrated adjustable
n Vista cab featuring:
Right hand side stairway on Spreader
n 2 Stage Boom armrest, high backrest, head rest
and handrails
n Integrated CH Spreader, ELME Model Seat-Side, Joystick Hydraulic Control and seat belt
817 with Mechanical Pile Slope Multifunctional Display Panel Electronic Twist Lock Position DC/DC converter 24 Volt/12 Volt
Telescoping & Tilting Steering Column Indicator with L.E.D. Signals and with 1 or 2 sockets
900 mm sliding cab Audible Tone (TWIST Module)
Floor Mat

10 11
STRONG PARTNERS. TOUGH TRUCKS.
TM

FOR DEMANDING OPERATIONS, EVERYWHERE.

Hyster supplies a complete range of warehouse equipment,

IC and electric counterbalanced trucks, container handlers
and reach stackers. Hyster is committed to being much more
than a lift truck supplier.

Our aim is to offer a complete partnership capable of

responding to the full spectrum of material handling issues:
Whether you need professional consultancy on your fleet
management, fully qualified service support, or reliable parts
supply, you can depend on Hyster.

Our network of highly trained dealers provides expert,

responsive local support. They can offer cost-effective finance
packages and introduce effectively managed maintenance
programmes to ensure that you get the best possible value.
Our business is dealing with your material handling needs so
you can focus on the success of your business today and in
the future.

HYSTER EUROPE
Centennial House, Frimley Business Park, Frimley, Surrey, GU16 7SG, England.
Tel: +44 (0) 1276 538500

www.hyster.eu @ infoeurope@hyster.com f /HysterEurope @HysterEurope /HysterEurope www.hyster-bigtrucks.com

HYSTER-YALE UK LIMITED trading as Hyster Europe. Registered Address: Centennial House, Building 4.5, Frimley Business Park, Frimley, Surrey, GU16 7SG, United Kingdom.
Registered in England and Wales. Company Registration Number: 02636775.
HYSTER, and FORTENS are registered trademarks in the European Union and certain other jurisdictions.
MONOTROL is a registered trademark, and DURAMATCH and are trademarks in the United States and in certain other jurisdictions.
Hyster products are subject to change without notice. Lift trucks illustrated may feature optional equipment.

Printed in Netherlands. Part Number: 3990525 Rev.0-01/16- TLC