Home / Operational Amplifiers / The Differential Amplifier

The Differential Amplifier

But as a standard operational amplifier has two inputs, inverting and no-inverting, we can also
connect signals to both of these inputs at the same time producing another common type of
operational amplifier circuit called a Differential Amplifier.
Basically, as we saw in the first tutorial about operational amplifiers, all op-amps are
Differential Amplifiers due to their input configuration. But by connecting one voltage signal
onto one input terminal and another voltage signal onto the other input terminal the resultant
output voltage will be proportional to the Difference between the two input voltage signals of
V1 and V2.
Related Products: OP Amp | SP Amplifier
Then differential amplifiers amplify the difference between two voltages making this type of
operational amplifier circuit a Subtractor unlike a summing amplifier which adds or sums
together the input voltages. This type of operational amplifier circuit is commonly known as
a Differential Amplifier configuration and is shown below:

Differential Amplifier

By connecting each input in turn to 0v ground we can use superposition to solve for the output
voltage Vout. Then the transfer function for a Differential Amplifier circuit is given as:
When resistors, R1 = R2 and R3 = R4 the above transfer function for the differential amplifier
can be simplified to the following expression:

Differential Amplifier Equation

If all the resistors are all of the same ohmic value, that is: R1 = R2 = R3 = R4 then the circuit
will become a Unity Gain Differential Amplifier and the voltage gain of the amplifier will be
exactly one or unity. Then the output expression would simply be Vout = V2 V1. Also note that
if input V1 is higher than input V2 the output voltage sum will be negative, and if V2 is higher
than V1, the output voltage sum will be positive.
The Differential Amplifier circuit is a very useful op-amp circuit and by adding more resistors
in parallel with the input resistors R1 and R3, the resultant circuit can be made to either Add or
Subtract the voltages applied to their respective inputs. One of the most common ways of
doing this is to connect a Resistive Bridge commonly called a Wheatstone Bridge to the input
of the amplifier as shown below.

Wheatstone Bridge Differential Amplifier

The standard Differential Amplifier circuit now becomes a differential voltage comparator by
Comparing one input voltage to the other. For example, by connecting one input to a fixed
voltage reference set up on one leg of the resistive bridge network and the other to either a
Thermistor or a Light Dependant Resistor the amplifier circuit can be used to detect either
low or high levels of temperature or light as the output voltage becomes a linear function of the
changes in the active leg of the resistive bridge and this is demonstrated below.

Light Activated Differential Amplifier

Here the circuit above acts as a light-activated switch which turns the output relay either ON or
OFF as the light level detected by the LDR resistor exceeds or falls below some pre-set value.
A fixed voltage reference is applied to the non-inverting input terminal of the op-amp via the R1
R2 voltage divider network.
The voltage value at V1 sets the op-amps trip point with a feed back potentiometer, VR2 used to
set the switching hysteresis. That is the difference between the light level for ON and the light
level for OFF.
The second leg of the differential amplifier consists of a standard light dependant resistor, also
known as a LDR, photoresistive sensor that changes its resistive value (hence its name) with the
amount of light on its cell as their resistive value is a function of illumination.
The LDR can be any standard type of cadmium-sulphide (cdS) photoconductive cell such as the
common NORP12 that has a resistive range of between about 500 in sunlight to about 20ks
or more in the dark.
The NORP12 photoconductive cell has a spectral response similar to that of the human eye
making it ideal for use in lighting control type applications. The photocell resistance is
proportional to the light level and falls with increasing light intensity so therefore the voltage
level at V2 will also change above or below the switching point which can be determined by the
position of VR1.
Then by adjusting the light level trip or set position using potentiometer VR1 and the switching
hysteresis using potentiometer, VR2 an precision light-sensitive switch can be made. Depending
upon the application, the output from the op-amp can switch the load directly, or use a transistor
switch to control a relay or the lamps themselves.
It is also possible to detect temperature using this type of simple circuit configuration by
replacing the light dependant resistor with a thermistor. By interchanging the positions
of VR1 and the LDR, the circuit can be used to detect either light or dark, or heat or cold using a
thermistor.
One major limitation of this type of amplifier design is that its input impedances are lower
compared to that of other operational amplifier configurations, for example, a non-inverting
(single-ended input) amplifier.
Each input voltage source has to drive current through an input resistance, which has less overall
impedance than that of the op-amps input alone. This may be good for a low impedance source
such as the bridge circuit above, but not so good for a high impedance source.
One way to overcome this problem is to add a Unity Gain Buffer Amplifier such as the voltage
follower seen in the previous tutorial to each input resistor. This then gives us a differential
amplifier circuit with very high input impedance and low output impedance as it consists of two
non-inverting buffers and one differential amplifier. This then forms the basis for most
Instrumentation Amplifiers.

Instrumentation Amplifier
Instrumentation Amplifiers (in-amps) are very high gain differential amplifiers which have a
high input impedance and a single ended output. Instrumentation amplifiers are mainly used to
amplify very small differential signals from strain gauges, thermocouples or current sensing
devices in motor control systems.
Unlike standard operational amplifiers in which their closed-loop gain is determined by an
external resistive feedback connected between their output terminal and one input terminal,
either positive or negative, instrumentation amplifiers have an internal feedback resistor that is
effectively isolated from its input terminals as the input signal is applied across two differential
inputs, V1 and V2.
The instrumentation amplifier also has a very good common mode rejection ratio, CMRR (zero
output when V1 = V2) well in excess of 100dB at DC. A typical example of a three op-amp
instrumentation amplifier with a high input impedance ( Zin ) is given below:

High Input Impedance Instrumentation Amplifier

The two non-inverting amplifiers form a differential input stage acting as buffer amplifiers with a
gain of 1 + 2R2/R1 for differential input signals and unity gain for common mode input signals.
Since amplifiers A1 and A2 are closed loop negative feedback amplifiers, we can expect the
voltage at Va to be equal to the input voltage V1. Likewise, the voltage at Vb to be equal to the
value at V2.
As the op-amps take no current at their input terminals (virtual earth), the same current must
flow through the three resistor network of R2, R1 and R2 connected across the op-amp outputs.
This means then that the voltage on the upper end of R1 will be equal to V1 and the voltage at
the lower end of R1 to be equal to V2.
This produces a voltage drop across resistor R1 which is equal to the voltage difference between
inputs V1 and V2, the differential input voltage, because the voltage at the summing junction of
each amplifier, Va and Vb is equal to the voltage applied to its positive inputs.
However, if a common-mode voltage is applied to the amplifiers inputs, the voltages on each
side of R1 will be equal, and no current will flow through this resistor. Since no current flows
through R1 (nor, therefore, through both R2 resistors, amplifiers A1 and A2 will operate as
unity-gain followers (buffers). Since the input voltage at the outputs of
amplifiers A1 and A2 appears differentially across the three resistor network, the differential
gain of the circuit can be varied by just changing the value of R1.
The voltage output from the differential op-amp A3 acting as a subtractor, is simply the
difference between its two inputs ( V2 V1 ) and which is amplified by the gain of A3 which
may be one, unity, (assuming that R3 = R4). Then we have a general expression for overall
voltage gain of the instrumentation amplifier circuit as:

Instrumentation Amplifier Equation

In the next tutorial about Operational Amplifiers, we will examine the effect of the output
voltage, Vout when the feedback resistor is replaced with a frequency dependant reactance in the
form of a capacitance. The addition of this feedback capacitance produces a non-linear
operational amplifier circuit called an Integrating Amplifier.