REPORT Automatic Transmission System
REPORT Automatic Transmission System
REPORT Automatic Transmission System
GEAR
TRASMISSION
SYSTEM
CONTENTS
1. ABSTRACT
2. Introduction
3. Transmission components
4. Working of transmission
5. Control system
ABSTRACT
The modern automatic transmission is by far, the most
complicated mechanical component in todays automobile. Automatic
transmission content mechanical systems, hydraulic systems, electrical
systems & computer controls, all working together in perfect harmony
which goes virtually unnoticed until there is a problem.
INTRODUCTION
If you have ever driven a car with an automatic transmission, then you know that there are
two big differences between an automatic transmission and a manual transmission:
There is no clutch pedal in an automatic transmission car.
There is no gear shift in an automatic transmission car. Once you put the transmission
into drive, everything else is automatic.
Both the automatic transmission (plus its torque converter) and a manual transmission (with
its clutch) accomplish exactly the same thing, but they do it in totally different ways. It
turns out that the way an automatic transmission does it is absolutely amazing!
In this article, we'll work our way through an automatic transmission. We'll start with the
key to the whole system: planetary gear sets. Then we'll see how the transmission is put
together, learn how the controls work and discuss some of the intricacies involved in
controlling a transmission.
Some Basics
Just like that of a manual transmission, the automatic transmission's primary job is to allow
the engine to operate in its narrow range of speeds while providing a wide range of output
speeds.
Without a transmission, cars would be limited to one gear ratio, and that ratio would have to
be selected to allow the car to travel at the desired top speed. If you wanted a top speed of
80 mph, then the gear ratio would be similar to third gear in most manual transmission cars.
You've probably never tried driving a manual transmission car using only third gear. If you
did, you'd quickly find out that you had almost no acceleration when starting out, and at
high speeds, the engine would be screaming along near the red-line. A car like this would
wear out very quickly and would be nearly undriveable.
So the transmission uses gears to make more effective use of the engine's torque, and to
keep the engine operating at an appropriate speed.
The key difference between a manual and an automatic transmission is that the manual
transmission locks and unlocks different sets of gears to the output shaft to achieve the
various gear ratios, while in an automatic transmission; the same set of gears produces all of
the different gear ratios. The planetary gearset is the device that makes this possible in an
automatic transmission.
Let's take a look at how the planetary gearset works.
When you take apart and look inside an automatic transmission, you find a huge assortment
of parts in a fairly small space. Among other things, you see:
The center of attention is the planetary gearset. About the size of a cantaloupe, this one
part creates all of the different gear ratios that the transmission can produce. Everything else
in the transmission is there to help the planetary gearset do its thing. This amazing piece of
gearing has appeared on HowStuffWorks before. You may recognize it from the electric
screwdriver article. An automatic transmission contains two complete planetary gearsets
folded together into one component. See How Gear Ratios Work for an introduction to
planetary gearsets.
From left to right: the ring gear, planet carrier, and two sun gears
Planetary Gearsets & Gear Ratios
Each of these three components can be the input, the output or can be held stationary.
Choosing which piece plays which role determines the gear ratio for the gearset. Let's
take a look at a single planetary gearset.
One of the planetary gearsets from our transmission has a ring gear with 72 teeth and a sun
gear with 30 teeth. We can get lots of
Gear different gear ratios out of this
Input Output Stationary Calculation gearset.
Ratio
Also, locking any two of the three
Planet
Sun components together will lock up the
A Carrier Ring (R) 1 + R/S 3.4:1 whole device at a 1:1 gear reduction.
(S) Notice that the first gear ratio listed
(C)
above is a reduction -- the output
Planet speed is slower than the input speed.
Ring 1 / (1 + The second is an overdrive -- the
B Carrier Sun (S) 0.71:1 output speed is faster than the input
(R) S/R) speed. The last is a reduction again,
(C)
but the output direction is reversed.
Sun Ring Planet There are several other ratios that can
C -R/S -2.4:1 be gotten out of this planetary gear
(S) (R) Carrier (C) set, but these are the ones that are
relevant to our automatic
transmission.
So this one set of gears can produce all of these different gear ratios without having to
engage or disengage any other gears. With two of these gearsets in a row, we can get the
four forward gears and one reverse gear our transmission needs. We'll put the two sets of
gears together in the next section.
Gears
This automatic transmission uses a set of gears, called a compound planetary gearset, that
looks like a single planetary gearset but actually behaves like two planetary gearsets
combined. It has one ring gear that is always the output of the transmission, but it has two
sun gears and two sets of planets.
Next you can see the inside of the planet carrier. The shorter gears are engaged only by the
smaller sun gear. The longer planets are engaged by the bigger sun gear and by the smaller
planets.
First Gear
In first gear, the smaller sun gear is driven clockwise by the turbine in the torque converter.
The planet carrier tries to spin counterclockwise, but is held still by the one-way clutch
(which only allows rotation in the clockwise direction) and the ring gear turns the output.
The small gear has 30 teeth and the ring gear has 72, so referring to the chart on this page,
the gear ratio is:
Ratio = -R/S = - 72/30 = -2.4:1
So the rotation is negative 2.4:1, which means that the output direction would be opposite
the input direction. But the output direction is really the same as the input direction -- this is
where the trick with the two sets of planets comes in. The first set of planets engages the
second set, and the second set turns the ring gear; this combination reverses the direction.
You can see that this would also cause the bigger sun gear to spin; but because that clutch is
released, the bigger sun gear is free to spin in the opposite direction of the turbine
(counterclockwise).
Second Gear
This transmission does something really neat in order to get the ratio needed for second
gear. It acts like two planetary gearsets connected to each other with a common planet
carrier.
The first stage of the planet carrier actually uses the larger sun gear as the ring gear. So the
first stage consists of the sun (the smaller sun gear), the planet carrier, and the ring (the
larger sun gear).
The input is the small sun gear; the ring gear (large sun gear) is held stationary by the band,
and the output is the planet carrier. For this stage, with the sun as input, planet carrier as
output, and the ring gear fixed, the formula is:
1 + R/S = 1 + 36/30 = 2.2:1
The planet carrier turns 2.2 times for each rotation of the small sun gear. At the second
stage, the planet carrier acts as the input for the second planetary gear set, the larger sun
gear (which is held stationary) acts as the sun, and the ring gear acts as the output, so the
gear ratio is:
1 / (1 + S/R) = 1 / (1 + 36/72) = 0.67:1
To get the overall reduction for second gear, we multiply the first stage by the second, 2.2 x
0.67, to get a 1.47:1 reduction. This may sound wacky, but it works.
Third Gear
Most automatic transmissions have a 1:1 ratio in third gear. You'll remember from the
previous section that all we have to do to get a 1:1 output is lock together any two of the
three parts of the planetary gear. With the arrangement in this gearset it is even easier -- all
we have to do is engage the clutches that lock each of the sun gears to the turbine.
If both sun gears turn in the same direction, the planet gears lockup because they can only
spin in opposite directions. This locks the ring gear to the planets and causes everything to
spin as a unit, producing a 1:1 ratio.
Overdrive
By definition, an overdrive has a faster output speed than input speed. It's a speed increase -
- the opposite of a reduction. In this transmission, engaging the overdrive accomplishes two
things at once. If you read How Torque Converters Work, you learned about lockup torque
converters. In order to improve efficiency, some cars have a mechanism that locks up the
torque converter so that the output of the engine goes straight to the transmission.
In this transmission, when overdrive is engaged, a shaft that is attached to the housing of
the torque converter (which is bolted to the flywheel of the engine) is connected by clutch
to the planet carrier. The small sun gear freewheels, and the larger sun gear is held by the
overdrive band. Nothing is connected to the turbine; the only input comes from the
converter housing. Let's go back to our chart again, this time with the planet carrier for
input, the sun gear fixed and the ring gear for output.
Ratio = 1 / (1 + S/R) = 1 / ( 1 + 36/72) = 0.67:1
So the output spins once for every two-thirds of a rotation of the engine. If the engine is
turning at 2000 rotations per minute (RPM), the output speed is 3000 RPM. This allows
cars to drive at freeway speed while the engine speed stays nice and slow.
Reverse
Reverse is very similar to first gear, except that instead of the small sun gear being driven
by the torque converter turbine, the bigger sun gear is driven, and the small one freewheels
in the opposite direction. The planet carrier is held by the reverse band to the housing. So,
according to our equations from the last page, we have:
Ratio = -R/S = 72/36 = 2.0:1
So the ratio in reverse is a little less than first gear in this transmission.
Gear Ratios
This transmission has four forward gears and one reverse gear. Let's summarize the gear
ratios, inputs and outputs:
Gear
Gear Input Output Fixed
Ratio
36-
30-tooth Planet
tooth 2.2:1
sun carrier
ring
36-
2nd Planet 72-tooth
tooth 0.67:1
carrier ring
sun
Total
1.47:1
2nd
30- and
72-tooth
3rd 36-tooth 1.0:1
ring
suns
36-
Planet 72-tooth
OD tooth 0.67:1
carrier ring
sun
After reading these sections, you are probably wondering how the different inputs get
connected and disconnected. This is done by a series of clutches and bands inside the
transmission. In the next section, we'll see how these work.
Clutches and Bands
In the last section, we discussed how each of the gear ratios is created by the transmission.
For instance, when we discussed overdrive, we said:
In this transmission, when overdrive is engaged, a shaft that is attached to the housing of
the torque converter (which is bolted to the flywheel of the engine) is connected by clutch
to the planet carrier. The small sun gear freewheels, and the larger sun gear is held by the
overdrive band. Nothing is connected to the turbine; the only input comes from the
converter housing.
To get the transmission into overdrive, lots of things have to be connected and disconnected
by clutches and bands. The planet carrier gets connected to the torque converter housing by
a clutch. The small sun gets disconnected from the turbine by a clutch so that it can
freewheel. The big sun gear is held to the housing by a band so that it could not rotate. Each
gear shift triggers a series of events like these, with different clutches and bands engaging
and disengaging. Let's take a look at a band.
Bands
In this transmission there are two bands. The bands in a transmission are, literally, steel
bands that wrap around sections of the gear train and connect to the housing. They are
actuated by hydraulic cylinders inside the case of the transmission.
Above you can see the two pistons that actuate the bands. Hydraulic pressure, routed into
the cylinder by a set of valves, causes the pistons to push on the bands, locking that part of
the gear train to the housing.
Clutches
The clutches in the transmission are a little more complex. In this transmission there are
four clutches
Each clutch is actuated by pressurized hydraulic fluid that enters a piston inside the clutch.
Springs make sure that the clutch releases when the pressure is reduced. Below you can see
the piston and the clutch drum. Notice the rubber seal on the piston -- this is one of the
components that is replaced when your transmission gets rebuilt.
One of the clutches in a transmission
The next figure shows the alternating layers of clutch friction material and steel plates. The
friction material is splined on the inside, where it locks to one of the gears. The steel plate is
splined on the outside, where it locks to the clutch housing. These clutch plates are also
replaced when the transmission is rebuilt.
The pressure for the clutches is fed through passageways in the shafts. The hydraulic
system controls which clutches and bands are energized at any given moment.
It may seem like a simple thing to lock the transmission and keep it from spinning; but there
are actually some complex requirements for this mechanism:
You have to be able to disengage it when the car is on a hill (the weight of the car is
resting on the mechanism).
You have to be able to engage the mechanism even if the lever does not line up with the
gear
Once engaged, something has to prevent the lever from popping up and disengaging.
The mechanism that does all this is pretty neat. Let's look at some of the parts first.
The output of the transmission: The square notches are engaged by the parking-brake
mechanism to hold the car still.
The parking-brake mechanism engages the teeth on the output to hold the car still. This is
the section of the transmission that hooks up to the drive shaft -- so if this part can't spin,
the car can't move.
The empty housing of the transmission with the parking brake mechanism poking
through, as it does when the car is in park
Above you see the parking mechanism protruding into the housing where the gears are
located. Notice that it has tapered sides. This helps to disengage the parking brake when
you are parked on a hill -- the force from the weight of the car helps to push the parking
mechanism out of place because of the angle of the taper.
This rod is connected to a cable that is operated by the shift lever in your car.
Top view of the park mechanism
the park mechanism is lined up so that it can drop into one of the notches in the output gear
section, the tapered bushing will push the mechanism down. If the mechanism is lined up
on one of the high spots on the output, then the spring will push on the tapered bushing, but
the lever will not lock into place until the car rolls a little and the teeth line up properly.
This is why sometimes your car moves a little bit after you put it in park and release the
brake pedal -- it has to roll a little for the teeth to line up to where the parking mechanism
can drop into place.
Once the car is safely in park, the bushing holds down the lever so that the car will not pop
out of park if it is on a hill.
Hydraulic System
The automatic transmission in your car has to do numerous tasks. You may not realize how
many different ways it operates. For instance, here are some of the features of an automatic
transmission:
If the car is in overdrive (on a four-speed transmission), the transmission will
automatically select the gear based on vehicle speed and throttle pedal position.
If you accelerate gently, shifts will occur at lower speeds than if you accelerate at full
throttle.
If you floor the gas pedal, the transmission will downshift to the next lower gear.
If you move the shift selector to a lower gear, the transmission will downshift unless
the car is going too fast for that gear. If the car is going too fast, it will wait until the
car slows down and then downshift.
If you put the transmission in second gear, it will never downshift or upshift out of
second, even from a complete stop, unless you move the shift lever.
You've probably seen something that looks like this before. It is really the brain of the
automatic transmission, managing all of these functions and more. The passageways you
can see route fluid to all the different components in the transmission. Passageways molded
into the metal are an efficient way to route fluid; without them, many hoses would be
needed to connect the various parts of the transmission. First, we'll discuss the key
components of the hydraulic system; then we'll see how they work together.
The Pump
Automatic transmissions have a neat pump, called a gear pump. The pump is usually
located in the cover of the transmission. It draws fluid from a sump in the bottom of the
transmission and feeds it to the hydraulic system. It also feeds the transmission cooler and
the torque converter.
The inner gear of the pump hooks up to the housing of the torque converter, so it spins at
the same speed as the engine. The outer gear is turned by the inner gear, and as the gears
rotate, fluid is drawn up from the sump on one side of the crescent and forced out into the
hydraulic system on the other side.
The Governor
The governor is a clever valve that tells the transmission how fast the car is going. It is
connected to the output, so the faster the car moves, the faster the governor spins. Inside the
governor is a spring-loaded valve that opens in proportion to how fast the governor is
spinning -- the faster the governor spins, the more the valve opens. Fluid from the pump is
fed to the governor through the output shaft.
The faster the car goes, the more the governor valve opens and the higher the pressure of
the fluid it lets through.
The governor
Valves and Modulators
To shift properly, the automatic transmission has to know how hard the engine is working.
There are two different ways that this is done. Some cars have a simple cable linkage
connected to a throttle valve in the transmission. The further the gas pedal is pressed, the
more pressure is put on the throttle valve. Other cars use a vacuum modulator to apply
pressure to the throttle valve. The modulator senses the manifold pressure, which drops
when the engine is under a greater load.
Manual Valve
The manual valve is what the shift lever hooks up to. Depending on which gear is selected,
the manual valve feeds hydraulic circuits that inhibit certain gears. For instance, if the shift
lever is in third gear, it feeds a circuit that prevents overdrive from engaging.
Shift Valves
Shift valves supply hydraulic pressure to the clutches and bands to engage each gear. The
valve body of the transmission contains several shift valves. The shift valve determines
when to shift from one gear to the next. For instance, the 1 to 2 shift valve determines when
to shift from first to second gear. The shift valve is pressurized with fluid from the governor
on one side, and the throttle valve on the other. They are supplied with fluid by the pump,
and they route that fluid to one of two circuits to control which gear the car runs in.
The shift valve will delay a shift if the car is accelerating quickly. If the car accelerates
gently, the shift will occur at a lower speed. Let's discuss what happens when the car
accelerates gently.
As car speed increases, the pressure from the governor builds. This forces the shift valve
over until the first gear circuit is closed, and the second gear circuit opens. Since the car is
accelerating at light throttle, the throttle valve does not apply much pressure against the
shift valve.
When the car accelerates quickly, the throttle valve applies more pressure against the shift
valve. This means that the pressure from the governor has to be higher (and therefore the
vehicle speed has to be faster) before the shift valve moves over far enough to engage
second gear.
Each shift valve responds to a particular pressure range; so when the car is going faster, the
2-to-3 shift valve will take over, because the pressure from the governor is high enough to
trigger that valve.
Electronic Controls
Electronically controlled transmissions, which appear on some newer cars, still use
hydraulics to actuate the clutches and bands, but each hydraulic circuit is controlled by an
electric solenoid. This simplifies the plumbing on the transmission and allows for more
advanced control schemes.
In the last section we saw some of the control strategies that mechanically controlled
transmissions use. Electronically controlled transmissions have even more elaborate control
schemes. In addition to monitoring vehicle speed and throttle position, the transmission
controller can monitor the engine speed, if the brake pedal is being pressed, and even the
anti-lock braking system.
Using this information and an advanced control strategy based on fuzzy logic -- a method of
programming control systems using human-type reasoning -- electronically controlled
transmissions can do things like:
Downshift automatically when going downhill to control speed and reduce wear on
the brakes
Up shift when braking on a slippery surface to reduce the braking torque applied by
the engine
Inhibit the up shift when going into a turn on a winding road
Let's talk about that last feature -- inhibiting the up shift when going into a turn on a
winding road. Let's say you're driving on an uphill, winding mountain road. When you are
driving on the straight sections of the road, the transmission shifts into second gear to give
you enough acceleration and hill-climbing power. When you come to a curve you slow
down, taking your foot off the gas pedal and possibly applying the brake. Most
transmissions will up shift to third gear, or even overdrive, when you take your foot off the
gas. Then when you accelerate out of the curve, they will downshift again. But if you were
driving a manual transmission car, you would probably leave the car in the same gear the
whole time. Some automatic transmissions with advanced control systems can detect this
situation after you have gone around a couple of the curves, and "learn" not to up shift
again.
For more information on automatic transmissions and related topics, check out the links on
the next page.
CONCLUSION
We can conclude from this seminar that, the automatic transmission system is more
advantageous over the conventional gearing mechanism. We can have a smooth drive and
easy gear changing system. This consists of all automatic controls which detect problems
occurred in system early on and warn the driver.