Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Automatic Transmission System

Download as doc, pdf, or txt
Download as doc, pdf, or txt
You are on page 1of 25

AUTOMATIC TRASMISSION

SYSTEM

SeminarsTopics.com
ABSTRACT

The modern automatic transmission is by far, the most complicated


mechanical component in today’s automobile. Automatic transmission content
mechanical systems, hydraulic systems, electrical systems & computer controls, all
working together in perfect harmony which goes virtually unnoticed until there is a
problem.

SeminarsTopics.com
INDEX

The article is broken down into five sections:

 Introduction breaks down in the simplest term what the purpose of a


transmission is.

 Transmission components describes the general principles behind each


system in simple terms to help you understand how an automatic
transmission works.

 Working of transmission describe the working of transmission at various


conditions like first gear, second gear, third gear over drive & reverse etc.

 Assessory components give the information of various other assessory


components in transmission.

 Control system: besides mechanical, hydraulic & other system like


electronic & computer systems are used in new cars.

SeminarsTopics.com
SeminarsTopics.com
INTRODUCTION

How Automatic Transmissions Work

If you have ever driven a car with an automatic transmission, then you know that
there are two big differences between an automatic transmission and a manual
transmission:
 There is no clutch pedal in an automatic transmission car.
 There is no gear shift in an automatic transmission car. Once you put the
transmission into drive, everything else is automatic.
Both the automatic transmission (plus its torque converter) and a manual
transmission (with its clutch) accomplish exactly the same thing, but they do it in
totally different ways. It turns out that the way an automatic transmission does it is
absolutely amazing!

Location of the automatic transmission

In this article, we'll work our way through an automatic transmission. We'll start
with the key to the whole system: planetary gear sets. Then we'll see how the
transmission is put together, learn how the controls work and discuss some of the
intricacies involved in controlling a transmission.

Some Basics

SeminarsTopics.com
Just like that of a manual transmission, the automatic transmission's primary job is
to allow the engine to operate in its narrow range of speeds while providing a wide
range of output speeds.

Mercedes-Benz CLK, automatic transmission, cut-away model

Without a transmission, cars would be limited to one gear ratio, and that ratio
would have to be selected to allow the car to travel at the desired top speed. If you
wanted a top speed of 80 mph, then the gear ratio would be similar to third gear in
most manual transmission cars.

You've probably never tried driving a manual transmission car using only third
gear. If you did, you'd quickly find out that you had almost no acceleration when
starting out, and at high speeds, the engine would be screaming along near the red-
line. A car like this would wear out very quickly and would be nearly undriveable.

So the transmission uses gears to make more effective use of the engine's torque,
and to keep the engine operating at an appropriate speed.

The key difference between a manual and an automatic transmission is that the
manual transmission locks and unlocks different sets of gears to the output shaft to
achieve the various gear ratios, while in an automatic transmission; the same set of
gears produces all of the different gear ratios. The planetary gearset is the device
that makes this possible in an automatic transmission.

Let's take a look at how the planetary gearset works.

SeminarsTopics.com
Planetary Gear sets

When you take apart and look inside an automatic transmission, you find a huge
assortment of parts in a fairly small space. Among other things, you see:

 An ingenious planetary gear set


 A set of bands to lock parts of a gear set
 A set of three wet-plate clutches to lock other parts of the gearset
 An incredibly odd hydraulic system that controls the clutches and bands
 A large gear pump to move transmission fluid around

The center of attention is the planetary gearset. About the size of a cantaloupe,
this one part creates all of the different gear ratios that the transmission can
produce. Everything else in the transmission is there to help the planetary gearset
do its thing. This amazing piece of gearing has appeared on HowStuffWorks
before. You may recognize it from the electric screwdriver article. An automatic
transmission contains two complete planetary gearsets folded together into one
component. See How Gear Ratios Work for an introduction to planetary gearsets.

From left to right: the ring gear, planet carrier, and two sun gears

SeminarsTopics.com
Planetary Gearsets & Gear Ratios

Any planetary gearset has three main components:


 The sun gear
 The planet gears and the planet gears' carrier
 The ring gear

Each of these three components can be the input, the output or can be held
stationary. Choosing which piece plays which role determines the gear ratio for
the gearset. Let's take a look at a single planetary gearset.

One of the planetary gearsets from our transmission has a ring gear with 72 teeth
and a sun gear with 30 teeth. We can get lots of different gear ratios out of this
gearset.
Gear
Input Output Stationary Calculation Also, locking any two of the
Ratio three components together will
Planet lock up the whole device at a 1:1
Sun gear reduction. Notice that the
A Carrier Ring (R) 1 + R/S 3.4:1 first gear ratio listed above is a
(S)
(C) reduction -- the output speed is
slower than the input speed. The
Planet second is an overdrive -- the
Ring
B Carrier Sun (S) 1 / (1 + S/R) 0.71:1 output speed is faster than the
(R) input speed. The last is a
(C) reduction again, but the output
Sun Ring Planet direction is reversed. There are
C -R/S -2.4:1 several other ratios that can be
(S) (R) Carrier (C) gotten out of this planetary gear
set, but these are the ones that are relevant to our automatic transmission.

So this one set of gears can produce all of these different gear ratios without having
to engage or disengage any other gears. With two of these gearsets in a row, we can
get the four forward gears and one reverse gear our transmission needs. We'll put
the two sets of gears together in the next section.

SeminarsTopics.com
Gears
This automatic transmission uses a set of gears, called a compound planetary
gearset, that looks like a single planetary gearset but actually behaves like two
planetary gearsets combined. It has one ring gear that is always the output of the
transmission, but it has two sun gears and two sets of planets.

Let's look at some of the parts:

How the gears in the transmission are put together


Left to right: the ring gear, planet carrier, and two sun gears

The figure below shows the planets in the planet carrier. Notice how the planet on
the right sits lower than the planet on the left. The planet on the right does not
engage the ring gear -- it engages the other planet. Only the planet on the left
engages the ring gear.

SeminarsTopics.com
Planet carrier: Note the two sets of planets.

Next you can see the inside of the planet carrier. The shorter gears are engaged
only by the smaller sun gear. The longer planets are engaged by the bigger sun gear
and by the smaller planets.

SeminarsTopics.com
First Gear

In first gear, the smaller sun gear is driven clockwise by the turbine in the torque
converter. The planet carrier tries to spin counterclockwise, but is held still by the
one-way clutch (which only allows rotation in the clockwise direction) and the ring
gear turns the output. The small gear has 30 teeth and the ring gear has 72, so
referring to the chart on this page, the gear ratio is:
Ratio = -R/S = - 72/30 = -2.4:1
So the rotation is negative 2.4:1, which means that the output direction would be
opposite the input direction. But the output direction is really the same as the input
direction -- this is where the trick with the two sets of planets comes in. The first
set of planets engages the second set, and the second set turns the ring gear; this
combination reverses the direction. You can see that this would also cause the
bigger sun gear to spin; but because that clutch is released, the bigger sun gear is
free to spin in the opposite direction of the turbine (counterclockwise).

Second Gear

This transmission does something really neat in order to get the ratio needed for
second gear. It acts like two planetary gearsets connected to each other with a
common planet carrier.

The first stage of the planet carrier actually uses the larger sun gear as the ring gear.
So the first stage consists of the sun (the smaller sun gear), the planet carrier, and
the ring (the larger sun gear).

The input is the small sun gear; the ring gear (large sun gear) is held stationary by
the band, and the output is the planet carrier. For this stage, with the sun as input,
planet carrier as output, and the ring gear fixed, the formula is:
1 + R/S = 1 + 36/30 = 2.2:1
The planet carrier turns 2.2 times for each rotation of the small sun gear. At the
second stage, the planet carrier acts as the input for the second planetary gear set,
the larger sun gear (which is held stationary) acts as the sun, and the ring gear acts
as the output, so the gear ratio is:
1 / (1 + S/R) = 1 / (1 + 36/72) = 0.67:1
To get the overall reduction for second gear, we multiply the first stage by the
second, 2.2 x 0.67, to get a 1.47:1 reduction. This may sound wacky, but it works.

SeminarsTopics.com
Third Gear

Most automatic transmissions have a 1:1 ratio in third gear. You'll remember from
the previous section that all we have to do to get a 1:1 output is lock together any
two of the three parts of the planetary gear. With the arrangement in this gearset it
is even easier -- all we have to do is engage the clutches that lock each of the sun
gears to the turbine.

If both sun gears turn in the same direction, the planet gears lockup because they
can only spin in opposite directions. This locks the ring gear to the planets and
causes everything to spin as a unit, producing a 1:1 ratio.

Overdrive
By definition, an overdrive has a faster output speed than input speed. It's a speed
increase -- the opposite of a reduction. In this transmission, engaging the overdrive
accomplishes two things at once. If you read How Torque Converters Work, you
learned about lockup torque converters. In order to improve efficiency, some cars
have a mechanism that locks up the torque converter so that the output of the
engine goes straight to the transmission.

In this transmission, when overdrive is engaged, a shaft that is attached to the


housing of the torque converter (which is bolted to the flywheel of the engine) is
connected by clutch to the planet carrier. The small sun gear freewheels, and the
larger sun gear is held by the overdrive band. Nothing is connected to the turbine;
the only input comes from the converter housing. Let's go back to our chart again,
this time with the planet carrier for input, the sun gear fixed and the ring gear for
output.
Ratio = 1 / (1 + S/R) = 1 / ( 1 + 36/72) = 0.67:1
So the output spins once for every two-thirds of a rotation of the engine. If the
engine is turning at 2000 rotations per minute (RPM), the output speed is 3000
RPM. This allows cars to drive at freeway speed while the engine speed stays nice
and slow.

Reverse
Reverse is very similar to first gear, except that instead of the small sun gear being
driven by the torque converter turbine, the bigger sun gear is driven, and the small
one freewheels in the opposite direction. The planet carrier is held by the reverse
band to the housing. So, according to our equations from the last page, we have:
Ratio = -R/S = 72/36 = 2.0:1
So the ratio in reverse is a little less than first gear in this transmission.

SeminarsTopics.com
Gear Ratios
This transmission has four forward gears and one reverse gear. Let's summarize the gear ratios,
inputs and outputs:

Gear
Gear Input Output Fixed
Ratio
30-tooth 72-tooth Planet
1st 2.4:1
sun ring carrier
36-
30-tooth Planet
tooth 2.2:1
sun carrier
ring
36-
2nd Planet 72-tooth
tooth 0.67:1
carrier ring
sun
Total
1.47:1
2nd
30- and
72-tooth
3rd 36-tooth 1.0:1
ring
suns
36-
Planet 72-tooth
OD tooth 0.67:1
carrier ring
sun
36-tooth 72-tooth Planet
Reverse -2.0:1
sun ring carrier

After reading these sections, you are probably wondering how the different inputs
get connected and disconnected. This is done by a series of clutches and bands
inside the transmission. In the next section, we'll see how these work.

Clutches and Bands

SeminarsTopics.com
In the last section, we discussed how each of the gear ratios is created by the
transmission. For instance, when we discussed overdrive, we said:

In this transmission, when overdrive is engaged, a shaft that is attached to the


housing of the torque converter (which is bolted to the flywheel of the engine) is
connected by clutch to the planet carrier. The small sun gear freewheels, and the
larger sun gear is held by the overdrive band. Nothing is connected to the turbine;
the only input comes from the converter housing.

To get the transmission into overdrive, lots of things have to be connected and
disconnected by clutches and bands. The planet carrier gets connected to the torque
converter housing by a clutch. The small sun gets disconnected from the turbine by
a clutch so that it can freewheel. The big sun gear is held to the housing by a band
so that it could not rotate. Each gear shift triggers a series of events like these, with
different clutches and bands engaging and disengaging. Let's take a look at a band.

Bands
In this transmission there are two bands. The bands in a transmission are, literally,
steel bands that wrap around sections of the gear train and connect to the housing.
They are actuated by hydraulic cylinders inside the case of the transmission.

One of the bands

In the figure above, you can see one of the bands in the housing of the
transmission. The gear train is removed. The metal rod is connected to the piston,
which actuates the band.

SeminarsTopics.com
The pistons that actuate the bands are visible here.

Above you can see the two pistons that actuate the bands. Hydraulic pressure,
routed into the cylinder by a set of valves, causes the pistons to push on the bands,
locking that part of the gear train to the housing.

Clutches
The clutches in the transmission are a little more complex. In this transmission
there are four clutches

Each clutch is actuated by pressurized hydraulic fluid that enters a piston inside the
clutch. Springs make sure that the clutch releases when the pressure is reduced.
Below you can see the piston and the clutch drum. Notice the rubber seal on the
piston -- this is one of the components that is replaced when your transmission gets
rebuilt.

SeminarsTopics.com
One of the clutches in a transmission

The next figure shows the alternating layers of clutch friction material and steel
plates. The friction material is splined on the inside, where it locks to one of the
gears. The steel plate is splined on the outside, where it locks to the clutch housing.
These clutch plates are also replaced when the transmission is rebuilt.

The pressure for the clutches is fed through passageways in the shafts. The
hydraulic system controls which clutches and bands are energized at any given
moment.

When You Put the Car in Park

It may seem like a simple thing to lock the transmission and keep it from spinning;
but there are actually some complex requirements for this mechanism:

 You have to be able to disengage it when the car is on a hill (the weight of
the car is resting on the mechanism).

You have to be able to engage the mechanism even if the lever does not line up
with the gear
 Once engaged, something has to prevent the lever from popping up and
disengaging.
The mechanism that does all this is pretty neat. Let's look at some of the parts first.

The output of the transmission: The square notches are engaged by the
parking-brake mechanism to hold the car still.

SeminarsTopics.com
The parking-brake mechanism engages the teeth on the output to hold the car still.
This is the section of the transmission that hooks up to the drive shaft -- so if this
part can't spin, the car can't move.

The empty housing of the transmission with the parking brake mechanism
poking through, as it does when the car is in park

Above you see the parking mechanism protruding into the housing where the gears
are located. Notice that it has tapered sides. This helps to disengage the parking
brake when you are parked on a hill -- the force from the weight of the car helps to
push the parking mechanism out of place because of the angle of the taper.

This rod actuates the park mechanism

This rod is connected to a cable that is operated by the shift lever in your car.

SeminarsTopics.com
Top view of the park mechanism

the park mechanism is lined up so that it can drop into one of the notches in the
output gear section, the tapered bushing will push the mechanism down. If the
mechanism is lined up on one of the high spots on the output, then the spring will
push on the tapered bushing, but the lever will not lock into place until the car rolls
a little and the teeth line up properly. This is why sometimes your car moves a little
bit after you put it in park and release the brake pedal -- it has to roll a little for the
teeth to line up to where the parking mechanism can drop into place.

Once the car is safely in park, the bushing holds down the lever so that the car will
not pop out of park if it is on a hill.

SeminarsTopics.com
Hydraulic System

The automatic transmission in your car has to do numerous tasks. You may not
realize how many different ways it operates. For instance, here are some of the
features of an automatic transmission:
 If the car is in overdrive (on a four-speed transmission), the transmission will
automatically select the gear based on vehicle speed and throttle pedal
position.
 If you accelerate gently, shifts will occur at lower speeds than if you
accelerate at full throttle.
 If you floor the gas pedal, the transmission will downshift to the next lower
gear.
 If you move the shift selector to a lower gear, the transmission will
downshift unless the car is going too fast for that gear. If the car is going too
fast, it will wait until the car slows down and then downshift.
 If you put the transmission in second gear, it will never downshift or upshift
out of second, even from a complete stop, unless you move the shift lever.

You've probably seen something that looks like this before. It is really the brain of
the automatic transmission, managing all of these functions and more. The
passageways you can see route fluid to all the different components in the
transmission. Passageways molded into the metal are an efficient way to route
fluid; without them, many hoses would be needed to connect the various parts of
the transmission. First, we'll discuss the key components of the hydraulic system;
then we'll see how they work together.

SeminarsTopics.com
The Pump

Automatic transmissions have a neat pump, called a gear pump. The pump is
usually located in the cover of the transmission. It draws fluid from a sump in the
bottom of the transmission and feeds it to the hydraulic system. It also feeds the
transmission cooler and the torque converter.

Gear pump from an automatic transmission

The inner gear of the pump hooks up to the housing of the torque converter, so it
spins at the same speed as the engine. The outer gear is turned by the inner gear,
and as the gears rotate, fluid is drawn up from the sump on one side of the crescent
and forced out into the hydraulic system on the other side.

SeminarsTopics.com
The Governor

The governor is a clever valve that tells the transmission how fast the car is going.
It is connected to the output, so the faster the car moves, the faster the governor
spins. Inside the governor is a spring-loaded valve that opens in proportion to how
fast the governor is spinning -- the faster the governor spins, the more the valve
opens. Fluid from the pump is fed to the governor through the output shaft.

The faster the car goes, the more the governor valve opens and the higher the
pressure of the fluid it lets through.

The governor

SeminarsTopics.com
Valves and Modulators

Throttle Valve or Modulator

To shift properly, the automatic transmission has to know how hard the engine is
working. There are two different ways that this is done. Some cars have a simple
cable linkage connected to a throttle valve in the transmission. The further the gas
pedal is pressed, the more pressure is put on the throttle valve. Other cars use a
vacuum modulator to apply pressure to the throttle valve. The modulator senses the
manifold pressure, which drops when the engine is under a greater load.

Manual Valve

The manual valve is what the shift lever hooks up to. Depending on which gear is
selected, the manual valve feeds hydraulic circuits that inhibit certain gears. For
instance, if the shift lever is in third gear, it feeds a circuit that prevents overdrive
from engaging.

Shift Valves

Shift valves supply hydraulic pressure to the clutches and bands to engage each
gear. The valve body of the transmission contains several shift valves. The shift
valve determines when to shift from one gear to the next. For instance, the 1 to 2
shift valve determines when to shift from first to second gear. The shift valve is
pressurized with fluid from the governor on one side, and the throttle valve on the
other. They are supplied with fluid by the pump, and they route that fluid to one of
two circuits to control which gear the car runs in.

SeminarsTopics.com
The shift valve will delay a shift if the car is accelerating quickly. If the car
accelerates gently, the shift will occur at a lower speed. Let's discuss what happens
when the car accelerates gently.

As car speed increases, the pressure from the governor builds. This forces the shift
valve over until the first gear circuit is closed, and the second gear circuit opens.
Since the car is accelerating at light throttle, the throttle valve does not apply much
pressure against the shift valve.

When the car accelerates quickly, the throttle valve applies more pressure against
the shift valve. This means that the pressure from the governor has to be higher
(and therefore the vehicle speed has to be faster) before the shift valve moves over
far enough to engage second gear.

Each shift valve responds to a particular pressure range; so when the car is going
faster, the 2-to-3 shift valve will take over, because the pressure from the governor
is high enough to trigger that valve.

Electronic Controls

Electronically controlled transmissions, which appear on some newer cars, still use
hydraulics to actuate the clutches and bands, but each hydraulic circuit is controlled
by an electric solenoid. This simplifies the plumbing on the transmission and
allows for more advanced control schemes.

In the last section we saw some of the control strategies that mechanically
controlled transmissions use. Electronically controlled transmissions have even
more elaborate control schemes. In addition to monitoring vehicle speed and
throttle position, the transmission controller can monitor the engine speed, if the
brake pedal is being pressed, and even the anti-lock braking system.

Using this information and an advanced control strategy based on fuzzy logic -- a
method of programming control systems using human-type reasoning --
electronically controlled transmissions can do things like:

 Downshift automatically when going downhill to control speed and reduce


wear on the brakes
 Up shift when braking on a slippery surface to reduce the braking torque
applied by the engine
 Inhibit the up shift when going into a turn on a winding road

Let's talk about that last feature -- inhibiting the up shift when going into a turn on
a winding road. Let's say you're driving on an uphill, winding mountain road.
SeminarsTopics.com
When you are driving on the straight sections of the road, the transmission shifts
into second gear to give you enough acceleration and hill-climbing power. When
you come to a curve you slow down, taking your foot off the gas pedal and
possibly applying the brake. Most transmissions will up shift to third gear, or even
overdrive, when you take your foot off the gas. Then when you accelerate out of
the curve, they will downshift again. But if you were driving a manual transmission
car, you would probably leave the car in the same gear the whole time. Some
automatic transmissions with advanced control systems can detect this situation
after you have gone around a couple of the curves, and "learn" not to up shift again.

For more information on automatic transmissions and related topics, check out the
links on the next page.

SeminarsTopics.com
CONCLUSION

We can conclude from this seminar that, the automatic transmission system is more
advantageous over the conventional gearing mechanism. We can have a smooth
drive and easy gear changing system. This consists of all automatic controls which
detect problems occurred in system early on and warn the driver.

COMPANIES WHICH MANUFACTURE AUTOMATIC TRANSMISSION


CARS:

TOYOTA, SUZUKI, VOLVO, MITSUBISHI, FIAT, FORD, DAEWOO, ACURA,


MERCIDIES BENZ, MERCURY, NISSAN etc.

SeminarsTopics.com

You might also like