Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
1K views

Calculating Thread Strength

Fasteners

Uploaded by

Mauricio Riquelme
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Calculating Thread Strength

Fasteners

Uploaded by

Mauricio Riquelme
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INDUSTRIAL FASTENERS INSTITUTE

6363 Oak Tree Boulevard Independence, Ohio 44131 USA, www.indfast.org

Calculating Thread Strength

An important fundamental of joint design is that, whenever possible, a joint should be designed so that the bolt or
screws breaking is the mode of failure. The reasoning behind this is if there is a product assembly error resulting in
a failed joint a broken screw or bolt is obvious where as a stripped bolt or internal thread is not. An obvious broken
screw or bolt can be replaced before the end product is put into service. When joint failure is by thread stripping that
failure may not become obvious until the end product is put into service resulting in much greater problems and as-
sociated cost of repair.

One of the most frequently asked applications questions is, What length of thread engagement is needed to avoid
thread strip-out? This is relatively easy to determine with a few facts and a little arithmetic.

The facts that are needed are as follows:


1. Thread size
2. Bolt material tensile strength
3. The tensile stress area (As)
4. The bolt thread shear area per inch (ASs)
5. The internal thread shear area per inch (ASn)
6. The shear strength of the material being tapped (tensile strength X 0.5)

All of this information is in the IFI 7th Edition Inch Standards Book for inch products and in the IFI 3rd Edition Metric
Standards Book for metric products. The chart below is an excerpt from the inch book.

Bolt tensile Stress Bolt Thread Internal Thread Stripping


Size Area sq. in. Stripping Areas sq. in. Areas sq. in. per in. of
per in. of Engagement Engagement
1/4-20 UNC 0.0318 0.368 0.539
5/16-18 UNC 0.0524 0.470 0.682
3/8-16 UNC 0.0775 0.576 0.828
7/16-14 UNC 0.106 0.677 0.981
1/2-13 UNC 0.142 0.779 1.12
9/16-12 UNC 0.182 0.893 1.27
5/8-11 UNC 0.226 0.998 1.42
3/4-10 UNC 0.334 1.21 1.72
7/8-9 UNC 0.462 1.43 2.03
1-8 UNC 0.606 1.66 2.33

IFI
Technical Bulletin
IFI
Published and issued by the
Calculating Thread Strength Page 1 of 2
Industrial Fasteners Institute Issued: March, 2009
of Independence, OH
All standards and specifications are advisory only. Their use by anyone is entirely voluntary. Reliance thereon for any purpose by anyone is at the sole risk of that person or the
user of the product, and the IFI is not responsible for any loss, claim, or damage arising therefrom. In formulating and approving standards and specifications, the IFI has not
investigated and will not investigate patents which may apply to the subject matter. Prospective users of the standards and specifications are responsible for advising themselves
of and protecting themselves against any patent infringement liability which may arise out of such use. INDUSTRIAL FASTENERS INSTITUTE 2009
INDUSTRIAL FASTENERS INSTITUTE
6363 Oak Tree Boulevard Independence, Ohio 44131 USA, www.indfast.org

Below is a sample calculation for an inch fastener application:

1. Thread size: -10


2. Bolt material tensile strength in PSI: SAE Grade 5 120,000 PSI
3. The tensile stress area per inch, As: 0.334 sq. in.
4. The bolt thread shear area per inch, ASs: 1.21 sq. in.
5. The internal thread shear area per inch, ASn: 1.72 sq. in.
6. The tensile strength of the material being tapped: 60,000 PSI
Note: The shear strength of steel is 50% of its tensile strength.

Steps Characteristic Formula


= As X bolt material tensile strength
-10 Grade 5 bolt tensile strength
1 = 0.334 X 120,000 PSI
(pounds)
= 40,080 pounds
= ASs X bolt shear strength
2 Bolt thread shear strength per inch = 1.21 X 60,000
= 72,600 pounds per inch
Length of engagement needed to avoid = bolt tensile strength bolt thread shear strength per inch
3
bolt thread stripping = 40,080 72,600 = 0.552 inches
= ASn X Internal thread shear strength
4 Internal thread shear strength per inch = 1.72 X 30,000 PSI
= 51,600 pounds per inch
Length of engagement needed to avoid = bolt tensile strength internal thread shear strength per inch
5
internal thread stripping = 40,080 51, 600 = 0.777 inches
Answer: 0.777 inches.
Conclusion: What length of engagement
To assure that thread stripping is NOT the failure mode select
6 will assure the mode of failure in this
the longer of the two thread stripping calculations. In this case
joint will NOT be thread stripping?
it was the length of engagement for the internal thread.

The conclusion of this analysis should always be to establish a length of thread engagement in the application that is
at least the length of the longer of the two thread shear area calculations. In no case should a length of engagement
be longer than 1.5 times the diameter of the thread be used as a length of engagement. When a length of thread
engagement longer than 1.5 D is used thread galling due to normal thread lead errors can occur. When this occurs
the thread galling prohibits achieving proper clamping in the joint.

Once a length of engagement is achieved that assures that bolt breaking will be the mode of failure in the joint ad-
ditional length of engagement does NOT enhance joint safety or reliability.

Disclaimer: All information provided in this document and/or presentation is based on data the Industrial Fasteners
Institute believes to be reliable and accurate. Such information is intended for use by persons at their own discretion
and risk. The information here in is based on industry standards and recognized practices. The Industrial Fasteners
Institute and the representatives providing this material assume no responsibility for the content.

IFI
Technical Bulletin
IFI
Published and issued by the
Calculating Thread Strength Page 2 of 2
Industrial Fasteners Institute Issued: March, 2009
of Independence, OH
All standards and specifications are advisory only. Their use by anyone is entirely voluntary. Reliance thereon for any purpose by anyone is at the sole risk of that person or the
user of the product, and the IFI is not responsible for any loss, claim, or damage arising therefrom. In formulating and approving standards and specifications, the IFI has not
investigated and will not investigate patents which may apply to the subject matter. Prospective users of the standards and specifications are responsible for advising themselves
of and protecting themselves against any patent infringement liability which may arise out of such use. INDUSTRIAL FASTENERS INSTITUTE 2009

You might also like