Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

04 Governors

Download as pdf or txt
Download as pdf or txt
You are on page 1of 31

THEORY OF MACHINES

AND MECHANISMS II
Mechanical IV/I
Chapter 4

Governors
THEORY OF MECHANISMS AND 1
MACHINES II
4.1 Introduction
The function of a governor is to regulate the mean speed of an engine, when
there are variations in the load .

When the load on an engine increases, its speed decreases, therefore it becomes
necessary to increase the supply of working fluid.

On the other hand, when the load on the engine decreases, its speed increases
and thus less working fluid is required.

The governor automatically controls the supply of working fluid to the engine
with the varying load conditions and keeps the mean speed within certain limits.

THEORY OF MECHANISMS AND 2


MACHINES II
4.2 Types of Governors

THEORY OF MECHANISMS AND 3


MACHINES II
Centrifugal Governors
In these governors, the change in centrifugal forces of the rotating masses due to
change in the speed of the engine is utilized for movement of the governor
sleeve. One of this type of governors is shown in Figure. These governors are
commonly used because of simplicity in operation.

THEORY OF MECHANISMS AND 4


MACHINES II
Inertia Governor

If the speed increases, then the mass G has a centripetal as well as tangential
component. This will result in an angular motion of G about O1 with angular
velocity arm and angular acceleration arm. It is seen that the directions of
rotation of the shaft and the arm are opposite to each other. The movement of the
arm is transferred to achieve governing. It has a very quick response.
THEORY OF MECHANISMS AND 5
MACHINES II
Terms Used in Governors
Height of a governor
It is the vertical distance from the centre of the ball to a point where the axes of
the arms (or arms produced) intersect on the spindle axis. It is usually denoted
by h.
Equilibrium speed
It is the speed at which the governor balls, arms etc., are in complete
equilibrium and the sleeve does not tend to move upwards or downwards.
Mean equilibrium speed
It is the speed at the mean position of the balls or the sleeve.
Maximum and minimum equilibrium speeds
The speeds at the maximum and minimum radius of
rotation of the balls, without tending to move either
way are known as maximum and minimum
equilibrium speeds respectively.
Sleeve lift
It is the vertical distance which the sleeve travels due to
change in equilibrium speed.
THEORY OF MECHANISMS AND 6
MACHINES II
4.2.1 Watt Governor
It is the original form of governor as used by Watt on some of his early steam
engines.
In this type of governor, each ball is attached to an arm, which is pivoted on the
axis of rotation.
The sleeve is attached to the governor balls by arms, pin-jointed at both ends,
and is free to slide along the governor shaft.

THEORY OF MECHANISMS AND 7


MACHINES II
It is assumed that the weight of the arms, links and the sleeve are
negligible as compared to the weight of the balls.
Taking moments about point O,

If N is the speed in r.p.m.,

At high speed the change in


height h is very small which
indicates that the sensitiveness of
the governor is very poor at high
speeds because of flatness of the
curve at higher speeds.
THEORY OF MECHANISMS AND 8
MACHINES II
4.2.2 Porter Governor
The Porter governor is a modification of a Watts governor, with central load
attached to the sleeve. The load moves up and down the central spindle. This
additional downward force increases the speed of revolution required to enable
the balls to rise to any predetermined level.

THEORY OF MECHANISMS AND 9


MACHINES II
Considering the equilibrium of the forces acting at D,

Resolving the forces acting at B vertically,


(1)

Resolving the forces acting at B horizontally,

(2)

THEORY OF MECHANISMS AND 10


MACHINES II
(1)

(2)

Dividing equation (2) by equation (1),

THEORY OF MECHANISMS AND 11


MACHINES II
When the length of arms are equal to the length of links and the points P and D
lie on the same vertical line, then
On comparing similar expression for
the Watt governor, we find that the
mass of the central load increase the
height of the governor in the ratio of
(1+M/m)
THEORY OF MECHANISMS AND 12
MACHINES II
4.2.3 Proell Governor
The Proell governor has the balls fixed at B and C to the extension of the links
DF and EG. The arms FP and GQ are pivoted at P and Q respectively.

The instantaneous centre (I) lies on the intersection of the line PF produced and
the line from D drawn perpendicular to the spindle axis. The perpendicular BM
is drawn on ID.
THEORY OF MECHANISMS AND 13
MACHINES II
Taking moments about I,

THEORY OF MECHANISMS AND 14


MACHINES II
In order to have the same equilibrium speed for the given
values of m, M and h, balls of smaller masses are used in
the Proell governor than in the Porter governor.

When = , then q = 1.

THEORY OF MECHANISMS AND 15


MACHINES II
4.2.4 Hartnell Governor
The two bell crank levers have been provided which can have rotating motion
about fulcrums O-O. One end of each bell crank lever carries a ball and a roller
at the end of other arm. The rollers make contact with the sleeve. The frame is
connected to the spindle. A helical spring is mounted around the spindle between
frame and sleeve. With the rotation of the spindle, all these parts rotate.

With the increase of speed, the radius of


rotation of the balls increases and the
rollers lift the sleeve against the spring
force. With the decrease in speed, the
sleeve moves downwards. The
movement of the sleeve are transferred
to the throttle of the engine through
linkages.

The spring force may be adjusted by


screwing a nut up or down on the
sleeve. THEORY OF MECHANISMS AND 16
MACHINES II
The minimum and maximum position is shown in Figure. Let h be the
compression of the spring when the radius of rotation changes from r1 to r2.
THEORY OF MECHANISMS AND 17
MACHINES II
For the minimum position i.e. when the radius of rotation changes from r to r1,
the compression of the spring or the lift of sleeve h1 is given by

For the maximum position i.e. when the radius of rotation changes from r to r2,
the compression of the spring or lift of sleeve h2 is given by

THEORY OF MECHANISMS AND 18


MACHINES II
(1) (2)

Adding equations (1) and (2),

(3)

Now for minimum position, taking moments about


point O,

(4)

Again for maximum position, taking moments about


point O,

(5)
19
THEORY OF MECHANISMS AND
MACHINES II
Subtracting equation (4) from equation (5),

Substituting

Neglecting the obliquity effect of the arms (i.e. x1 = x2 = x, and y1 = y2 = y) and


the moment due to weight of the balls (i.e. m.g), we have for minimum position,

... (6)

Similarly for maximum position,


... (7)

Subtracting equation (6) from equation (7),


... (8)

THEORY OF MECHANISMS AND 20


MACHINES II
Substituting

.. (9)

Since the stiffness for a given spring is constant for all positions, therefore for
minimum and intermediate position,
.. (10)

For intermediate and maximum position,

.. (11)

From equations (9), (10) and (11),

THEORY OF MECHANISMS AND 21


MACHINES II
4.2.5 Hartung Governor
A spring controlled governor of the Hartung type is shown in Figure. In this
type of governor, the vertical arms of the bell crank levers are fitted with spring
balls which compress against the frame of the governor when the rollers at the
horizontal arm press against the sleeve.

Neglecting the effect of obliquity of the arms, taking moments about the
fulcrum O,

THEORY OF MECHANISMS AND 22


MACHINES II
4.2.6 Wilson-Hartnell Governor
A Wilson-Hartnell governor is a governor in which the balls are connected by a
spring in tension as shown in Figure. An auxiliary spring is attached to the
sleeve mechanism through a lever by means of which the equilibrium speed for
a given radius may be adjusted. The main spring may be considered of two equal
parts each belonging to both the balls.

THEORY OF MECHANISMS AND 23


MACHINES II
Now total downward force on the sleeve

Taking moments about O,

At minimum equilibrium speed,

At maximum equilibrium speed,

Subtracting

THEORY OF MECHANISMS AND 24


MACHINES II
When the radius increases from r1 to r2, the
ball springs extend by the amount 2 (r2
r1) and the auxiliary spring extend by the
amount .

Substituting the values of (P2 P1) and (S2 S1)

THEORY OF MECHANISMS AND 25


MACHINES II
4.2.7 Pickering Governor
A Pickering governor is mostly used for driving gramophone. It consists of
three straight leaf springs arranged at equal angular intervals round the spindle.
Each spring carries a weight at the centre. The weights move outwards and the
springs bend as they rotate about the spindle axis with increasing speed.

THEORY OF MECHANISMS AND 26


MACHINES II
The maximum deflection of a leaf spring with both ends fixed and carrying a
load (W) at the centre is,

In case of a Pickering governor, the central load is the centrifugal force

Substituting the value of W

The empirical relation between the lift of the sleeve and the deflection is
approximately given as

THEORY OF MECHANISMS AND 27


MACHINES II
4.3 Performance of Governors
4.3.1 Sensitiveness of Governors
Sensitiveness is defined as the ratio of the difference between the maximum and
minimum equilibrium speeds to the mean equilibrium speed.

4.3.2 Stability of Governors


A governor is said to be stable when for every speed within the working range
there is a definite configuration i.e. there is only one radius of rotation of the
governor balls at which the governor is in equilibrium. For a stable governor, if
the equilibrium speed increases, the radius of governor balls must also increase.
THEORY OF MECHANISMS AND 28
MACHINES II
4.3.3 Isochronous Governors
A governor is said to be isochronous when the equilibrium speed is constant (i.e.
range of speed is zero) for all radii of rotation of the balls within the working
range, neglecting friction. The isochronism is the stage of infinite sensitivity.

4.3.4 Hunting
A governor is said to be hunt if the speed of the engine fluctuates continuously
above and below the mean speed. This is caused by a too sensitive governor
which changes the fuel supply by a large amount when a small change in the
speed of rotation takes place.

THEORY OF MECHANISMS AND 29


MACHINES II
Example 4.1
A loaded governor of the Porter type has equal arms and links each
250 mm long. The mass of each ball is 2 kg and the central mass is
12 kg. When the ball radius is 150 mm, the valve is fully open and
when the radius is 185 mm, the valve is closed. Find the maximum
speed and the range of speed. If the maximum speed is to be
increased 20% by an addition of mass to the central load, find
what additional mass is required.

192.98 r.p.m. ; 16.03 r.p.m.; 6.16 kg

THEORY OF MECHANISMS AND 30


MACHINES II
Example 4.2
A Hartnell governor has a speed range of 290 rpm to 310 rpm for
a lift of 15 mm. The sleeve arm and the ball arm 80 mm and 120
mm respectively. The radius of rotation of the balls is 120 mm
from the governor axis, when the ball arm is vertical and the speed
of the governor is minimum. If the mass of each ball is 2.5 kg,
determine:
a) load on the spring for minimum and maximum speeds, and
b) spring rate.
830.034 N, 1126.307 N, 19.751 kN/m

THEORY OF MECHANISMS AND 31


MACHINES II

You might also like