How Students Are Graded
How Students Are Graded
How Students Are Graded
Systems Course
1 Grading
The final grading of the Advanced Control Systems course is based on written exam (40 points), TP
reports (30 points) and evaluation meeting (30 points). The final grade then is computed using the
following table.
Points 96-100 91-95 86-90 61-65 56-60 51-55 6-10 1-5 0
Grade 6.00 5.75 5.50 4.25 4.00 3.75 1.50 1.25 1.00
2 Written Exam
The exam is open book and open notes. The use of scientific calculator is allowed but not the computer.
The questions and problems are limited to Chapter 1 and Chapter 3 of the course-notes. The learning
outcomes of each chapter are evaluated by the problems and questions that are detailed as follows.
2.1 Chapter 1
The student should be able to
Compute any norm of a given signal or system (see Example 1.2 and Example 1.3).
v(t)
r(t) e(t) u(t)
- ?
h y(t)
+
- h - K - G
-
6
Which criterion should be minimized to minimize the two norm of the output when
r(t) = 0 and (1) v(t) is a Dirac impulse signal, (2) v(t) is a step signal, (3) v(t) = sin 0 t,
(4) v(t) is a bounded two-norm signal whose energy is concentrated between 1 and 2 .
1
Convert parametric and multimodel uncertainty to unstructured frequency-domain uncertainty (i.e.
additive, multiplicative, feedback uncertainty). See Examples 1.6, 1.7, 1.8 and 1.9.
Find the limit of achievable performance for unstable and non-minimum phase systems.
Example: Given
s1 k
G(s) = and W1 (s) =
s2 s+1
find for which values of k > 0 the nominal performance W1 S < 1 can be achieved.
2.2 Chapter 3
The student should be able to design RST digital controllers
with specifications on desired closed-loop poles.
with fixed terms in the controller,
for internal model control, model reference control and minimum variance control,
using Q parameterization for robustness.
See Example 3.5, 3.7 and the following examples:
0.5q 1 0.4q 2
G(q 1 ) =
1 1.2q 1 + 0.35q 2
Design an IMC controller with integrator and the same dynamics for tracking and regu-
lation.
Example 2: Consider the following plant model:
0.5(z 0.8)
G(z) =
(z 0.7)(z 0.5)
Take Pd (q 1 ) = 1 0.6q 1 and the same dynamics for tracking and regulation. Compute
R0 (q 1 ), S0 (q 1 ) and T0 (q 1 ). Add HR (q 1 ) = 1 + q 1 and an integrator into the
controller using Q parameterization.
Example 3: Consider the following plant model:
0.5q 1 0.4q 2
G(q 1 ) =
1 1.2q 1 + 0.35q 2
2
3 TP Reports
Every group of two students prepares one report per TP and submits it on the moodle in due time. Each
TP report will be evaluated before the evaluation meeting based on the completeness and correctness of
the results and the clarity of presentation. Each report has maximum 15 points which is given equally to
both students. The grade, however, is provisional and will be reduced after the evaluation meeting if it
turns out that the students (or one of them) are not aware of what is written in the report.
4 Evaluation Meeting
The evaluation meeting will be planned individually during the exam period via moodle. Each meeting
will last about 15 minutes. During the meeting the students can only use their reports (no access to
the course-notes). The objective of this meeting is to evaluate the level of understanding of the students
about the subject of the TPs and the course (especially Chapter 2 and Chapter 4).
4.1 TP questions:
Assume that a student has used the following command in his/her report:
performance=conper(LS,[Mm,Ku,wh],wc/s);
The student may be asked the following questions:
Explain the loop shaping method, which criterion is minimized?
Why the desired loop is chosen as wc/s?
What is the definition of the modulus margin Mm?
What are Ku and wh? How they are chosen? How they are implemented as constraints in the
optimization problem?
Explain the decreasing gain, constant forgetting factor, variable forgetting factor and constant
trace.
2. Adaptive Control:
What is an adaptive control system. Give its general scheme and compare it with conventional
and robust control.
Compare direct and indirect adaptive control.
Give the block-diagram of Model Reference Adaptive Control.
3
Explain the certainty equivalence and separation principles.
Explain three strategies for the implementation of the indirect adaptive control.
3. Switching Adaptive Control:
Give the block-diagram of the switching adaptive control and compare it with gain-scheduled
control.
Explain the monitoring signal and the switching logic.
Discuss the stability of switching adaptive control for the trivial case and nontrivial case.
What is the injected system and in which condition the injected system is stable?