Design of Building Foundations

The most common types of foundations for domestic and light commercial buildings are the
strip and the pad foundation respectively. In this section the design of these two foundations
will be discussed.
Figure 4-1 shows a narrow strip foundation which is a long strip of concrete supporting the
walls of a low-rise domestic building. It can also be used for other buildings, if the factors
favour such a choice. From the wall the loading is spread on the foundation at 45 as shown
in Figure App7.1a. The planes through which the loading is distributed are called the shear
planes. The foundation should be designed in such a way that the shear planes pass through
the lower corners of the strip. If the designed foundation width is too wide, as is the case in
weaker soils, plain concrete strip may bend and crack as shown in Figure App7.1b. Concrete
may be made stronger in tension by providing steel reinforcement in the tension zone.
Ground level Ground level

Depth dependent on
soil conditions
D = P or 150 mm
P P whichever is greater
Mass concrete (1:3:6)

D
15 N/mm 2
Shear plane
Shear plane Cracks
(a) (b)
Figure App7.1 Strip foundation
According to the Building Regulations, the design of a strip foundation should satisfy the
following conditions*:
i) The projections of the concrete strip on either side of the wall should be equal.
ii) The thickness of the concrete strip should either be equal to the projection (D = P) or 150
mm, whichever is greater. This means that the minimum thickness of strip foundation is 150
mm.
Example 1:
Design a strip foundation for a domestic building to satisfy the following conditions:
i) The walls are 275 mm thick cavity walls.
ii) The building load, including the dead load of the foundation, is 40 kN/m.
iii) The safe bearing capacity of the subsoil is 80 kN/m2
Solution:
As the walls and the foundation are very long, the calculations are based on 1 m length of the
wall/foundation. The area of the foundation can be determined from the formula:
Building load
Area of the building foundation = Safe bearing capacity
40
= 80 = 0.5 m2
Area of strip foundation = Width 1 m length = 0.5 m2
Therefore, width of the foundation = 0.5 m2
This is the minimum requirement.
The normal practice is to provide 600 mm wide foundation. Each projection will be:
(600 275) 2 = 162.5 mm

The shear planes are drawn at 45 from points c and d, as shown in Figure App7.2, and
vertical lines drawn from points a and b. These lines cross at points e and f, which are joined
to complete the design of the foundation.
The thickness of concrete strip in this case is 162.5 mm which may be increased to 170 mm.
Pad foundation
Pad foundation, also known as isolated foundation, is used for columns of low and medium
rise framed buildings. For light structures, plain or reinforced concrete may be used, but for
heavier structures reinforced concrete is used.
a 162.5 162.5 b
c d
e f
Shear plane
Figure App7.2 Design of strip foundation
Un-reinforced pads are designed on the basis that no tension occurs in the concrete. The
thickness is determined as explained in the design of strip foundation. Nominal reinforcement
is still required to control thermal cracking of concrete.
Example 2:
Design a pad foundation for a 300 300 mm column, carrying a load of 500 kN. The safe
bearing capacity of the subsoil is 200 kN/m2.
Solution:
Column load
Area of the pad foundation = Safe bearing capacity
500
= 200 = 2.5 m2
A square pad is usually provided for a square column.
Side of the square pad = 2.5 = 1.6 m or 1600 mm
The thickness of the pad can be determined by drawing the shear planes at 45 as shown in
Figure App7.3. In order that the shear planes pass through the lower corners of the pad,
thickness D must be equal to projection P.
Projection P = (1600 300) 2 = 650 mm.
Thickness of pad foundation, D = P = 650 mm.

Shear plane
Figure App7.3 Design of a concrete pad
*Extract reproduced from The Building Regulations (2000), Approved Document A
Structure, Department of Communities and Local Government under the Open Government
Licence v 1.0. Website: www.nationalarchives.gov.uk

Design of Building Foundations

Uploaded by

Copyright:

Available Formats

Design of Building Foundations

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design of Building Foundations

Uploaded by

Copyright:

Available Formats

The most common types of foundations for domestic and light commercial buildings are the

Ground level Ground level

Mass concrete (1:3:6)

Figure App7.1 Strip foundation

i) The walls are 275 mm thick cavity walls.

iii) The safe bearing capacity of the subsoil is 80 kN/m2

Area of strip foundation = Width 1 m length = 0.5 m2

Therefore, width of the foundation = 0.5 m2

This is the minimum requirement.

(600 275) 2 = 162.5 mm

to complete the design of the foundation.

heavier structures reinforced concrete is used.

Figure App7.2 Design of strip foundation

thickness is determined as explained in the design of strip foundation. Nominal reinforcement

is still required to control thermal cracking of concrete.

bearing capacity of the subsoil is 200 kN/m2.

A square pad is usually provided for a square column.

Side of the square pad = 2.5 = 1.6 m or 1600 mm

thickness D must be equal to projection P.

Projection P = (1600 300) 2 = 650 mm.

Thickness of pad foundation, D = P = 650 mm.

Figure App7.3 Design of a concrete pad

*Extract reproduced from The Building Regulations (2000), Approved Document A

Licence v 1.0. Website: www.nationalarchives.gov.uk

You might also like