B ENGINE

ACC
SECTION
ACCELERATOR CONTROL SYSTEM C

E
CONTENTS
ACCELERATOR CONTROL SYSTEM ...................... 2 ASSEMBLY ........................................................... 3 F
Removal and Installation .......................................... 2 SERVICE DATA AND SPECIFICATIONS (SDS) ........ 5
ADJUSTABLE ACCELERATOR PEDAL Accelerator Control ................................................... 5
ASSEMBLY ........................................................... 2 ACCELERATOR PEDAL STROKE AND G
NON-ADJUSTABLE ACCELERATOR PEDAL TRAVEL ................................................................. 5

Revision: April 2004 ACC-1 2004 Titan

 ACCELERATOR CONTROL SYSTEM

ACCELERATOR CONTROL SYSTEM PFP:18005

Removal and Installation EBS00HZO

ADJUSTABLE ACCELERATOR PEDAL ASSEMBLY

Adjustable Accelerator Pedal

LBIA0379E

1. Adjustable accelerator pedal assem- 2. Adjustable accelerator pedal bracket 3. Adjustable pedal electric motor (part
bly (part of the accelerator pedal assembly) of the accelerator pedal assembly)
4. Adjustable brake pedal cable (part
of the accelerator pedal assembly)

CAUTION:
Do not disassemble the accelerator pedal adjusting mechanism.
Before removal and installation, the accelerator and brake pedals must be in the frontmost posi-
tion. This is to align the base position of the accelerator and brake pedals.
Do not disassemble the accelerator pedal assembly.
Do not remove the accelerator pedal position sensor from the accelerator pedal bracket.
Avoid damage from dropping the accelerator pedal assembly during handling.
Keep the accelerator pedal assembly away from water.
Removal
1. Move the accelerator and brake pedals to the frontmost position.
2. Turn the ignition switch OFF and disconnect the negative battery terminal.
3. Disconnect the adjustable brake pedal cable from the adjustable brake pedal.
Unlock, then pull the adjustable brake pedal cable to disconnect it from the adjustable brake pedal.

Revision: April 2004 ACC-2 2004 Titan

 ACCELERATOR CONTROL SYSTEM

4. Disconnect the adjustable pedal electric motor electrical connec-

tor. A
5. Disconnect the adjustable pedal electric motor memory electri-
cal connector, if equipped.
6. Disconnect the accelerator position sensor electrical connector. ACC
7. Remove the two upper and one lower accelerator pedal nuts.
8. Remove the adjustable accelerator pedal assembly.
C

LBIA0380E

D
Installation
Installation is in the reverse order of removal.
Inspection After Installation E
Check that the accelerator pedal moves smoothly within the specified ranges.
Adjustable accelerator pedal total pedal applied stroke : 48.3 mm (1.90 in)
F
Adjustable accelerator pedal total pedal adjustment travel : 73.2 mm (2.88 in)
Depress and release the accelerator pedal to check that it returns smoothly to the original released posi-
tion. G
Perform an electrical inspection of the accelerator pedal position sensor. Refer to EC-556, "DTC P2138
APP SENSOR" .
CAUTION: H
When the harness connector of the accelerator pedal position sensor is disconnected, perform
Accelerator Pedal Released Position Learning. Refer to EC-44, "Accelerator Pedal Released
Position Learning" .
I
NON-ADJUSTABLE ACCELERATOR PEDAL ASSEMBLY
Non-Adjustable Accelerator Pedal
J

LBIA0404E

Revision: April 2004 ACC-3 2004 Titan

 ACCELERATOR CONTROL SYSTEM

1. Non-adjustable accelerator pedal 2. Non-adjustable accelerator pedal position 3. Non-adjustable accelerator pedal
A/T cable attachment bracket sensor (part of the accelerator pedal assembly
(part of the accelerator pedal assembly)
assembly)

CAUTION:
Do not disassemble the accelerator pedal assembly.
Do not remove the accelerator pedal position sensor from the accelerator pedal bracket.
Avoid damage from dropping the accelerator pedal assembly during handling.
Keep the accelerator pedal assembly away from water.
Removal
1. Turn the ignition switch OFF and disconnect the negative battery terminal.
2. Disconnect the accelerator position sensor electrical connector.
3. Remove the two upper and one lower accelerator pedal nuts.
4. Remove the adjustable accelerator pedal assembly.
Installation
Installation is in the reverse order of removal.
Inspection After Installation
Check that the accelerator pedal moves smoothly within the specified range.
Non-adjustable accelerator pedal total pedal applied stroke : 48 mm (1.89 in)
Depress and release the accelerator pedal to check that it returns smoothly to the original released posi-
tion.
Perform an electrical inspection of the accelerator pedal position sensor. Refer to EC-556, "DTC P2138
APP SENSOR" .
CAUTION:
When the harness connector of the accelerator pedal position sensor is disconnected, perform
Accelerator Pedal Released Position Learning. Refer to EC-44, "Accelerator Pedal Released
Position Learning" .

Revision: April 2004 ACC-4 2004 Titan

 SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030

A
Accelerator Control EBS00HZP

ACCELERATOR PEDAL STROKE AND TRAVEL

Unit: mm (in)
ACC
Non-adjustable accelerator pedal - total pedal applied stroke 48 (1.89)
Adjustable accelerator pedal - total pedal applied stroke 48.3 (1.90)
Adjustable accelerator pedal - total pedal adjustment travel 73.2 (2.88) C

Revision: April 2004 ACC-5 2004 Titan

 SERVICE DATA AND SPECIFICATIONS (SDS)

Revision: April 2004 ACC-6 2004 Titan