Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 34 views

    Acc PDF

    Uploaded by

    Evan Vlogz
    The document provides instructions for removing, installing, and adjusting the accelerator control system on a vehicle. It contains the following key points: 1. The accelerator wire should be adjusted any time parts of the accelerator control system are removed or replaced. 2. When adjusting the accelerator wire, apply vacuum to the throttle opener to free it from the throttle drum rod. Then loosen the lock nut and tighten the adjusting nut until the throttle drum starts to move. 3. From that position, turn the adjusting nut back 1.5 to 2 turns and tighten the lock nut to specification. Release the vacuum and reinstall components.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Acc PDF

    Uploaded by

    Evan Vlogz
    34 views4 pages
    The document provides instructions for removing, installing, and adjusting the accelerator control system on a vehicle. It contains the following key points: 1. The accelerator wire should be adjusted any time parts of the accelerator control system are removed or replaced. 2. When adjusting the accelerator wire, apply vacuum to the throttle opener to free it from the throttle drum rod. Then loosen the lock nut and tighten the adjusting nut until the throttle drum starts to move. 3. From that position, turn the adjusting nut back 1.5 to 2 turns and tighten the lock nut to specification. Release the vacuum and reinstall components.

    Original Title

    acc.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for removing, installing, and adjusting the accelerator control system on a vehicle. It contains the following key points: 1. The accelerator wire should be adjusted any time parts of the accelerator control system are removed or replaced. 2. When adjusting the accelerator wire, apply vacuum to the throttle opener to free it from the throttle drum rod. Then loosen the lock nut and tighten the adjusting nut until the throttle drum starts to move. 3. From that position, turn the adjusting nut back 1.5 to 2 turns and tighten the lock nut to specification. Release the vacuum and reinstall components.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    34 views4 pages

    Acc PDF

    Uploaded by

    Evan Vlogz
    The document provides instructions for removing, installing, and adjusting the accelerator control system on a vehicle. It contains the following key points: 1. The accelerator wire should be adjusted any time parts of the accelerator control system are removed or replaced. 2. When adjusting the accelerator wire, apply vacuum to the throttle opener to free it from the throttle drum rod. Then loosen the lock nut and tighten the adjusting nut until the throttle drum starts to move. 3. From that position, turn the adjusting nut back 1.5 to 2 turns and tighten the lock nut to specification. Release the vacuum and reinstall components.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    B ENGINE

    ACC
    SECTION
    ACCELERATOR CONTROL SYSTEM C

    E
    CONTENTS
    ACCELERATOR CONTROL SYSTEM ...................... 2 Removal and Installation .......................................... 2 F
    Adjusting Accelerator Wire ....................................... 2

    ACC-1
    ACCELERATOR CONTROL SYSTEM

    ACCELERATOR CONTROL SYSTEM PFP:18005

    Removal and Installation EBS00EZD

    Accelerator Pedal and Wire

    WFE022

    CAUTION:
    ● The accelerator wire should be adjusted when removing or replacing any parts of the Accelerator
    Control System.
    ● Check that throttle valve opens fully when accelerator pedal is fully depressed. Also check that
    the throttle valve returns to the idle position when the pedal is released.
    ● Check the accelerator control parts for interference contact with any adjacent parts.
    ● When connecting the accelerator wire, be careful not to twist or scratch the inner wire.
    ● Refer toACS-23, "ASCD Wire Adjustment" .
    Adjusting Accelerator Wire EBS00EZE

    NOTE:
    Adjust the accelerator wire with the engine warmed up to normal operating temperature and the ignition switch
    turned to OFF.
    1. Remove the vacuum hose connected to the throttle opener.
    2. Connect a suitable vacuum hose to the vacuum pump.
    3. Apply vacuum [more than -40.00 kPa (-300 mmHg, -11.81 inHg)]
    until the throttle drum becomes free from the rod of the throttle
    opener.
    ● Make sure that there is clearance between the throttle drum
    and rod.
    – If there is no clearance, refer to EC-73, "Basic Inspection"
    (KA24DE), or EC-637, "Basic Inspection" (VG33E), or EC-
    1237, "Basic Inspection" (VG33ER). SEF793W
    – If there is clearance, go to the following steps.

    ACC-2
    ACCELERATOR CONTROL SYSTEM

    4. Loosen the lock nut and tighten the accelerator adjusting nut
    until the throttle drum starts to move. A
    5. From that position, turn back the adjusting nut 1.5 to 2 turns, and
    tighten the lock nut to specification as shown.
    6. Release the vacuum from the throttle opener. ACC
    7. Remove the vacuum pump hose from the throttle opener.
    8. Reinstall the original vacuum hose to the throttle opener.
    C

    SFE249AE

    ACC-3
    ACCELERATOR CONTROL SYSTEM

    ACC-4

    You might also like