Technical Data Sheet

Approved 388;26160;21800;21740;21860 1,2 388 unsaturated ^(ValidationDate) 1

polyester

Baltoflake

Product description
This is a glass flake reinforced unsaturated polyester coating. It is an ultra high build, extremely abrasion
resistant and fast curing barrier coating. Can be used as primer, mid coat or finish coat in atmospheric and
immersed environments. Suitable for properly prepared carbon steel, stainless steel, aluminium and approved
primers.

Typical use
Recommended for areas subject to extreme mechanical wear and harsh exposure conditions. Recommended for
offshore environments, including splash zones, jetties, piles, tidal zones, decks, battery rooms, power stations,
exterior of buried tanks, concrete bunds, refineries, bridges, mining equipment and general structural steel
where future maintenance is challenging.
Other

Approvals and certificates

APAS approved to specification 2917, 2917F, 2917P and 2917S
Norsok M501 / ISO 20340
Additional certificates and approvals may be available on request.

Colours
selected range of colours

Product data
Property Test/Standard Description
Solids by volume calculated 96 2 %
Gloss level (GU 60 ) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 34 C
Density calculated 1,2 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 80 g/l
VOC-EU IED (2010/75/EU) (calculated) 4 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 80 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
Gloss description: According to Jotun Performance Coatings' definition.

Film thickness per coat

Typical recommended specification range

Dry film thickness 600 - 1500 m

Wet film thickness 650 - 1650 m
Theoretical spreading rate 1,5 - 0,6 m/l

Date of issue: 24 August 2017 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Baltoflake

All vinyl ester and polyester resin systems are subject to some shrinkage during the curing process. This results
in a practical spreading rate lower than the theoretically calculated. The shrinkage depends on actual dry film
thickness applied and conditions during application.

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel Sa 2 (ISO 8501-1) with a surface Sa 2 (ISO 8501-1) with a surface
profile Medium to Coarse G (ISO profile Medium to Coarse G (ISO
8503-2) 8503-2)
Aluminium Cleanliness and surface profile Cleanliness and surface profile
corresponding to the description of Sa corresponding to the description of Sa
2 (ISO 8501-1), Fine to Medium G 2 (ISO 8501-1), Fine to Medium G
(ISO 8503-2) (ISO 8503-2)
Stainless steel Cleanliness and surface profile Cleanliness and surface profile
corresponding to the description of Sa corresponding to the description of Sa
2 (ISO 8501-1), Fine G (ISO 2 (ISO 8501-1), Fine G (ISO 8503-2)
8503-2)
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Spray: Standard airless spray may be used. Dedicated two component airless spray is an option.

Mixing ratio table - Additives

The steel temperature shall not be lower than the paint temperature and not more than 20 C above the paint
temperature.
Additive volumes (ml) in 16 litres product.

Paint temperature
Additive 10-14 C 15-19 C 20-24 C 25-29 C 30-34 C 35-40 C

Jotun Accelerator CO1P 300 *

Jotun Peroxide 1 or Andonox KP-9 300 * 300 * 200 * 200 200 200
Jotun Inhibitor 51 200 200 400

Date of issue: 24 August 2017 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Baltoflake

* Not applicable for Baltoflake FC

For other additive suppliers please consult Jotun.

WARNING:
Accelerators must never come in direct contact with peroxides.
All peroxides must be stored in a dark and cool storage room (below 25 C), and kept away from all kind of
combustible materials. Exposure to direct sunlight must be avoided. Use only original or approved containers.
Empty containers should be washed with water and kept in separate storage/containers.
The peroxide may catch fire if exposed to sparks or to hot metal dust from grinding or other mechanical work.
The curing reaction develops heat. For leftovers of mixed paint it is recommended to fill the tin with water to
avoid excessive heat development.

Thinner/Cleaning solvent
Thinner: Styrene

Thinning max.: 5 %

Cleaning solvent: Jotun Thinner No. 17 / Jotun Thinner No. 27

Guiding data for airless spray

Nozzle tip (inch/1000): 27-35

Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time

Substrate temperature 10 C 23 C 40 C

Baltoflake
Surface (touch) dry 3 h 2 h 2 h
Walk-on-dry 5 h 2 h 2 h
Dry to over coat, minimum 5 h 2 h 2 h
Dried/cured for service 4 d 2 d 1 d

Baltoflake FC
Surface (touch) dry 2h 2h
Walk-on-dry 2h 2h
Dried/cured for service 2d 1d

For maximum overcoating intervals, refer to the Application Guide (AG) for this product.

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Baltoflake FC should not be overcoated with itself or Baltoflake.

Procedure for repair of minor areas are found under Repair of coating system.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Date of issue: 24 August 2017 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Baltoflake

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 C

Pot life 45 min

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 90 C 100 C

Immersed, sea water 50 C -

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Note that the coating will be resistant to various immersion temperatures depending on the specific chemical
and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If
used as part of a system, ensure all coatings in the system have similar heat resistance.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: unsaturated polyester, unsaturated vinyl ester

Subsequent coat: unsaturated polyester, polyurethane, polysiloxane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Baltoflake 16 20

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Date of issue: 24 August 2017 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Baltoflake

Shelf life at 23 C
Baltoflake 6 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 24 August 2017 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com