Development of Stupa Architecure in India PDF
Development of Stupa Architecure in India PDF
Development of Stupa Architecure in India PDF
CHAPTER 3
DEVELOPMENT OF STUPA
ARCHITECTURE IN INDIA
The study in evolution of Indian Architecture especially of Buddhist Architecture has
attracted the fascination of scholars from throughout the world. The earliest man made structural
dwelling in the country are residential structure meant for habitation, secular and are reported from
the early phase of proto-historic period. The religious buildings came in to existence with the
growth of religious pantheons. In the history of Indian civilization Buddhism, which besides being
one of the oldest religions, has been a way of life and a socio-cultural system. A myriad variety of
architecture was conceived, patronized and constructed by the Buddhists throughout the length and
breadth of the country. Of these, Stupa architecture occupied a very important place. The Stupa
architecture in its origin, evolution and structural arrangement remains an exciting architectural
phenomenon. The reasons very aptly quoted by Susila Panth (Panth 1976: xi) in the following
words:-
The word Stupa is mentioned in the Rigveda, Atharvaveda, Vajasaneyi Samhita, Taittriya
Samhita, in the Panchavimsata Brahmana and the Monier-Williams Sanskrit-English Dictionary
49
which says it a knot or tuft of hair, the upper part of head, crest, top, summit, a heap or pile of
earth or bricks etc.
Rigveda refers to a Stupa raised by the King Varuna above the forest in a place having no
foundation (Rigveda; verse 28). The word estuka is also used in the same sense in Rigveda,
probably by then anything raised on the ground like a heap/pile might have been known as Stupa.
However the Pali word thupa is quite similar to the term Stupa. Thupa means a conical heap, a
pile or a mound or a conical or bell shaped shrine containing a relic (Panth 1976:3).
The word tope for Stupa was first introduced into English by Elphinstone in his account of the
tope of Manikyala in the Rawalpindi District in the year 1839: Tope is an expression used for a
mound or barrow (hill or hillock) as far west as Peshawar... ( Tucci 1988: p-ix); (also see Mount-
Stewart Elphinstone, Account of the kingdom of Caubool, 2nd ed.,1.108, cited from Hobson-Jobson
1903:934-935).
architecture acquired prominence in the socio cultural life of the country and art began to develop
around the Stupa structure.
According to A. Cunningham, Maisey and Foucher the remains of the Stupa found at Sanchi
can be classified into three categories (Cunningham1847:473)
1. Religious edifies or Stupa dedicated either to the celestial or the Adi-Buddha or to the
mortal Buddha.
2. Funeral Stupa erected over the relics of mortal Buddha or over his disciples.
3. Stupa for commemorative Buddha.
Satapatha Brahmana mentions of raising a mound on the burial ground after cremation. The
burial mound for the Devata should be square in shape. In the Jaina and Brahmanical texts in some
places Stupa is termed as chaitya. In the Vedic, Post Vedic, Epics, Jaina and Buddhist literatures
refers to the existence of chaitya-vriksha. These were mostly treated as sacred places but were not
necessarily associated with burial.
It is doubtful if any Stupas were erected during the life time of Buddha. Since he had declared
that it was inappropriate to erect Stupa to enshrine his bodily remains while he was still alive,
however the legend says that the Buddha gave a few strands of his hair (kasha asthi) to the
merchants Tapassu and Bhallika, who had offered him the first meal after his enlightenment at
Bodhgaya. They were said to have erected a Stupa over the hair relic so as to venerate them.
Burmese Buddhist claims that these hair relics are enshrined in the Shwedagon Stupa at Yangon,
though it is generally believed that the merchants hailed from ancient Kalinga.
After the demise of Buddha and his cremation at Kushinagar and later the corporeal relics was
distributed among eight Mahajanapadas, initially eight Stupas (Saririka Chaityas) were constructed
at eight centres namely, Rajagrihya, Vaishali, Kapilavastu, Allakappa, Ramagrama, Vethadipa,
Pava and Kushinara. Drona the Brahmin who initiated the distribution, himself erected a Stupa to
enshrine the urn that was used to divide the relics.
The Moriyas arrived too late for a share of the relic and were given the wood ashes from the
cremation pyre, and they too built a Stupa in their city of Pipphalavana. Thus all together ten
Stupas were erected i.e. eight on corporeal relics and two on urn and over wood ashes by Drona
and the Moriyas respectively.
Jatakas mentions about the existence of Stupa but does not throw any light on the structural
details of Stupa. The Sujata Jataka and the Bahiya Sutta describes Stupas as raised earthen mounds
to commemorate the deceased. This indicates that most probably prior to Ashoka most of the
51
Stupas were made of clay (Pant 1976:3). Even the original Stupa at Sanchi and Bharhut are said to
be made of clay.
Archaeological excavations and findings proved that during Ashokas reign use of bricks and
stone for constructional purpose became popular. But we cannot deny the fact that the predecessors
of Ashoka like Bimbisara and Ajatsatru both had constructed a number of Stupas in honour of the
Buddha which contained relics of Buddha (Mahaparinibban Sutta:83).
If Buddhism is a jewel with many facets, then the Stupa must be the natural expressions of this
in architectural form. Multifarious in form but common in spirit, it adorns the landscape in places
where Buddhism has taken root. Buddhists of all lands see the Stupa as a representation of the
Buddha and his enlightenment. The Stupa thus is a monument erected over the relic of a Buddha or
an enlightened disciple, or at places consecrated as scenes of his acts. According to the Chinese
pilgrims Fa-hsien and Hsuan-tsang seeing Stupas which are said to have enshrined the objects
which have been used by Buddha (paribhogika Stupa) i.e. his robe, bowl or walking staff, but
archaeologically it is to be proven.
With the emergence of Mahayana sect it was not necessary that all the Stupas contained relics.
It was taken over by the image worship, with the transformation from non-iconic to iconic for
changes were also found in the architectural patterns. Mahayanist focused on miniature Stupas as
donative structures for the sake of getting salvation which lead o multiplicity of Stupas without
containing relics.
According to B.M.Barua (1934), Stupa architecture can be compared with different stages of
mans life. He observes putting of the relics in covered casket indicated stage of conception;
putting of casket in a stone box indicates birth; covering of the box by a brick structure as infancy;
the rise of the structure above the ground (medhi) as childhood; oval shaped (anda) that of
adolescence; the chatravali and in compassing it by a stone railing keeping guard that of youth and
coronation; the lion statues guarding the approaches are that of manhood; erection of ornamental
archways and completion of sculptural representations that of maturity and victory; the addition of
an outer railing and construction of the flights of steps that of decline and old age.
After Ashoka none of the Mauryan ruler showed any interest in propagating Buddhism. Then
the Sungas gave a new dimension to the Stupa architecture. They ruled over north, central and
western India between one hundred and eighty five BCE to 70 BCE Sunga and Kanva gave ample
opportunity to fine art reflected the cultural and traditional life of the larger section of the people in
the society i.e. the bas reliefs on the railings of the Stupa at Bharhut. During Sunga and Ekshakus
period enlargement and additions were made in the existing Stupas of Sanchi, Bharhut and
Amravati.
52
Sungas were followed by a spate of Yavanas invasions the Bacterians, Greeks, Saka and
Kushana on India. The Sakas took over Saurastra and probably Taxila and Mathura. The Kushanas
extended their empire from Kabul to Kashmir in the north-west to the whole of northern India.
Kanishka (78 -120 CE) and Huviska (120 140 CE) contributed significantly to the Buddhist
architectural movement. During Kanishkas reign a number of Stupas were constructed at Taxila,
rock-cut Stupa architecture was introduced by him. It is recorded that Kanishka erected a Stupa to
enshrine a scripture called Vibhasas (commentaries of the Sarvastivada tradition) at the end of the
fourth Buddhist council (Weng Yew 1999:32). Gandhara and Mathura art flourished during
Kushana period. Both these schools of art introduced iconic representations of the Buddha.
There are also Stupas, which do not hold any reliquary object inside. These are
commemorative Stupas, which are erected at places associated with Buddhas life or that of his
renowned disciple.
The architectural movement in the south (Andhra) flourished under Satavahanas (100 BCE
200 CE). Rock cut architecture of Hinayana sect became more prominent. There is very little
information regarding the history of the development of Stupa architecture in north. The Gupta
period is considered as the golden age of Indian history. Guptas were Vaishnavites but were
tolerant towards Buddhism. It is said that the Stupa at Sarnath was built during the Gupta period.
Unfortunately in India all the later structural examples of stupas are n ruins, the upper portions
having decayed and disappeared. But a few good specimens belonging to this period still survive in
the form of Votive stupas of stone and metal, literature, and specimens in Ceylon and Burma.
golden urn, a Stupa of his physical body at the crossing of four main roads built, along with
umbrellas, banners and flags.
Anathapindada places the relics, alms-bowl and robe on a prominent place of his house to
enable people to come and pay their homage. Once he had to lock the house and go out and the
people who had come to pay homage got annoyed. So, Anathapindada placed the matter before
Buddha, whom he asked to allow him to built a Stupa for the venerable Sariputra.
Buddha gives his consent and gives the following instructions to build a Stupa:
(1) In due subsequent order at first four terraces, (2) the receptacle for the pot are to
be made, (3) the pot, (4) the vessel, (5) the pole, (6) the umbrella canopy from one to
thirteen (superimposed) umbrella canopies and (7) the protection against rain are to be made.
Buddha says about the different numbers of superimposed umbrella canopies to be assigned
are, that Stupas for Tathagatas should be thirteen (superimposed) umbrella canopies, for Pratyeka-
Buddhas without any protection against rain, Stupas of Arhats should have four umbrella
canopies, of those who do not return(an-agamin) three, of those who return (ago-min) two, and of
those who have entered the stream (being converted) only one and Stupas for laymen are to be
constructed without umbrella canopies.
When Buddha was asked that in which place Sariputras Stupa should be constructed, he said
that it should be built in accordance with the rank or order of seats which both Sariputra and
Maudgalyanaputra occupied in the Samgha in relation to the seat of the Tathagata. Respectively,
the Stupas of other elder members are to be arranged in due order of their rank. Stupas of the
virtuous laymen however have to be constructed outside the Samgha compound (Dorjee 1996:3).
Thus these descriptions precisely illustrate the main structures of the Buddhist Stupa including
the structural distinctions for the different classes of the Buddhist saints, are indicated by the
number of umbrella assigned to them. This narration is one of the oldest Stupa references in the
Buddhist testament.
Each disc of the umbrella has its own significance and is assigned as follows:
54
The first disc represents the mystical power to know the ability to perceive what is the position
and what is not the position for the preaching and activity of the Buddha.
The second disc represents the mystical power to know the ability to perceive that everybody
is responsible for his karma.
The third disc represents the mystical power to know the ability to perceive all meditations,
liberation, concentration and union with superior spheres.
The fourth disc represents the mystical power to know the ability to perceive the superior and
low moral faculties.
The fifth disc represents the mystical power to know the ability to perceive the various
inclinations of beings.
The sixth disc represents the mystical power to know the ability to perceive the different
spheres of existence.
The seventh disc represents the mystical power to know the ability to perceive the way leading
to any desired place.
The eighth disc represents the mystical power to know the ability to remember previous
existences.
The ninth disc represents the mystical power to know the ability to perceive the time of death
and rebirth.
The tenth disc represents the mystical power consisting of destroying sinful forces.
The eleventh, twelfth and thirteenth disc represents the three supports of awareness unusual to
the Buddha.
It was probably during the reign of Ashoka, that the royal umbrella first became associated
with the stupas in India after he made Buddhism the state religion. (Longhurst 1992: 16-17)
Vinaya Uttaragrantha
This text records the tradition of the construction of a Stupa the Buddhas hair and nails. There
is a long list of additional structural components and ornamental parts which are slowly added to
the Stupa constructed over Buddhas hair and nails by Anathapindaka during his life time.
The following account is mentioned in the seventh stanza of the sutra (Dorjee 1996:4);(also
see Kagyur, Vinaya, Derge, Vol.PA, (Toh.7) fol.264b6). With Buddhas permission Anathapindaka
white washes the Stupa build over the hair and nails of Lord Buddha to make it look attractive.
55
Later he realised that the Stupa did not look nice in the evening due to lack of illumination. So, he
requests Buddha to allow him to offer a circle of butter lamp and the installation of the lamps were
tested in three ways: by putting the lamps on the upper part of the Stupa, which tarnished the white
colour of the Stupa due to dripping of the oil and the lamps were place in the lower part from where
the lamps were easily accessible to dogs who consumed the oil and which caused the architect to
make niches for holding the lamps.
Similar problem arose with regards to the cattle that polluted the area around the Stupa by
strewing their dung. So, in Buddhas concern railings were erected all around the Stupa and
gateways (torana) were also added to it.
Vimalosnisa
The Tantric section of the Tangyur Testament contains twin works on Vimalosnisa, one
attributed to Sahajavilasa and the other to the anonymous.
According to Sahajavilasa one should erect the Stupa over the corporeal relics of Lord
Buddha on a hill or a plain or a valley and avoid a cemetery. The text in particular points the
various structural components of the Stupa and their proportions to be kept in mind during
construction and at the end of the text it talks about the colours to be put to the structural
components of the Stupa.
Chaitya-Vibhanga-Vinayaddhrta-Sutra
This text is the Tibetan version entitled, Mchod rten gyi cha dbye ba dul ba las byung ba i
mdo, of the lost Sanskrit original manuscript. This is mentioned in the Tantric section of the
Tangyur testament (Dorjee 1996:10); (also see Narthang, Vol. TU, fol.174a3-5; Derge, Vol. PU
(Text 3078), fol.173b3-175b1; and Peking, Vol. TU, fol.187b4-189b7).
The text deals with the symbolical meanings of the main structure of the Stupa, in order of
their sequences with the essence of the Tathagatas Dharmakaya. The essence are the four close
mindfulness, the four perfect abandonments, the four miracle powers, the five faculties, the five
forces, the seven factors of enlightenment, the eight fold noble paths, ten types of consciousness,
ten mystical powers, the three absolute unshared mindfulness, and the great compassion that are
connected with the structures of Stupa by the following references: the reflected image of these
sets of above mentioned notions are called as the reflected image of the Dharmakaya.
The ancient Indian literature is abounding with Stupa construction manuals which provide
sources for the study of the Buddhist Stupa. These Stupas can be seen all over India, Nepal, Tibet,
Mongolia, Bhutan and parts of China in various sizes built according to the specifications
mentioned in the literature.
56
Stupa also symbolises Buddhas enlightened mind and his teachings and few Stupas were built
to enshrine Buddhist scriptures. Furthermore the architectural elements of a Stupa are symbolic of
the doctrine and may vary with tradition. In some Theravada traditions the parts of the Stupa
represents the divisions of the noble eight-fold path (ethical conduct, concentration, wisdom and
nirvana).
The Buddhist Stupas are of three kinds, saririka Stupa raised over the relics of Buddha or
Arhants. The existence of such Stupas is archaeologically proven in several places like Sanchi,
Taxila, Vaishali, Piprahwa, Bhattiprolu and Nagarjunikunda. Paribhogika Stupas are the Stupas
which enshrine the objects which have been used by the Buddha such as robe, bowl or walking
staff. Fa-hsien and Hsuan-tsang the Chinese pilgrims reported seeing Stupas enshrining such relics
but archaeologically it has to be proven. Uddesika Stupas were erected just for worshipping and
contained no relics or to enshrine scriptures. The Stupa raised by Ashoka in the Lumbini garden
visited by the emperor on his twentieth regnal year accompanied by his teacher Upagupta. Another
example is when King Kaniska had built a magnificent Stupa to enshrine the Vibhasas
(commentaries of the Sarvastivada tradition) at the end of the fourth Buddhist council.
The Vajrayana tradition attributes the components of the Stupa to each of the five elements
(earth, water, fire, air and space). These elements represent the different stages in the
transformation of psycho-spiritual energy in the path to enlightenment. Hence being an object for
devotion, the Stupa also became an instrument for meditative visualisation.
to the Ashoka period. Similar instances are found in the Stupas at Taxila and Nagarjunakonda),
making it difficult to describe the shape of the earliest Stupas. For this one has to fall back on
sculptural representations of them in order to form a correct idea of their appearance when
complete; fortunately there are plenty of materials for this purpose (Longhurst 1992: 14)
The Stupa symbolised legitimating through sanctification and stability. The signs of
sanctification were the addition of a tuft hair, representing supreme power. Stability was shown by
a stump or wooden shaft as the axial pillar in the centre of the monument. Irwin (1979:838)
emphasizes that the primary component of the early Stupa had been an axial pillar of wood. The
wooden shaft in the centre of the Stupa was found at Vaishali, Bihar. Here the first recorded
excavation was conducted in the year 1800.
After the first century CE, Stupa architecture underwent a gradual transformation. The heights
of the accessory parts became more accentuate.
The Stupas in ancient India were generally composed of three parts (Fig. 3).
1. The base or drum.
2. The dome (anda) which resting on the drum, demarcating a terrace called medhi in the
Divyavadana (Cowell & Neil 1886:244) and in Ceylon, pupphaddhana, a Pali word meaning
place for depositing flowers. The relics are kept in the hollow space in the interior of the dome of
a Stupa. The relic casket is generally made of precious metal in the shape of a miniature Stupa.
3. The upper part is made up of a square structure called harmika (meaning Pavilion), into
which the shaft (yupa) bearing the umbrellas (chatra) is inserted. The term harmika is not available
in the Mahavamsa, and this part of the Stupa is called caturassa-caya meaning quadrangular
enclosure. In Ceylon, it is also called devata kotuwa, citadel of Gods. (Benisti 2003:6); (also see
Pranavitana, The Stupa in Ceylon, in MASC V 1947:16. Mahavamsa XXXI: 124).
The Stupa comprising of the above three parts was generally surrounded by a railing, this
space was used by the devotees for performing pradikshina, a rite of worship. The pradikshina-
patha (circumambulatory passage) of the Stupa was often paved with stone panels bearing votive
inscriptions. In the Mahavamsa this railing is called pada-vedika: railing at the foot or ground
railing around the Stupa.
The vedika reminds of the ancient wooden railings, it is made up of a plinth (alambana),
upright (stambha) in to which cross-bars (suchi) are fitted followed by a coping stone (usnisha).
According to Coomarswamy, this part of the vedika is called usnisha turban, it is due to its
relationship to the Stupa which it encircles, like a turban or ribbon encircles the head of the person
wearing it. It is generally cut by one or four doorways. The toranas are built up of two large
pillars linked by two or three lintels. Close to the toranas are isolated lat pillars holding various
58
symbols above a capital. Hiuen-tsang mentions the existence of these columns erected in front of
Stupas in his writings. According to him, one was erected to recall the circumstances of the death
of the Buddha, another one with inscription, to mark that it was here that the relic was divided. He
mentions one more whose surface is polished and were we can constantly see the shadow of the
Buddha.
Generally the bigger Stupas were constructed of bricks, some small ones were made of soap
stone or blue schist, etc. The bigger ones were plastered which is mentioned in the texts: for
example, in the Mahavastu it is said that a Stupa was built too big nor too small, covered with clay
(mrttika) and stucco (sudha); the same word is found in the Mahavamsa. Wood was also used in
construction; it is thus that a story from the Sutralamkara mentions a tree which was used as a
beam for supporting a Stupa.
In the earliest phase the Stupa was always in the shape of a large hemisphere resting on a
drum. It is only after the fifth century CE (Intermediate period) that it underwent two important
modifications: basement on the one hand, and the crown on the other, concurrently increasing their
importance to the determent of the dome which earlier constituted the entire structure. (Fig.3)
The later versions in contrast, were tall, often resting on a higher platform with the
surmounting structures such as the chatra becoming more elongated (Late period) and spire-shaped
(Fig.3).
The early Stupas such as at Sanchi and Bharhut, only the railings were decorated with motives
and symbols later doors and domes became covered like them with bas-reliefs representing scenes
from the Buddhas life and from jataka. Hence a Stupa worked like a book in stone offered for
mediation to the devotees who came to circumambulate around the Stupa.
The images of the masters appeared only in the first century CE till then his presence was
represented only as symbols.
elaborate scale for the bigger Stupas , such as at Bharhut, Sanchi, Amravati and at Bodhgaya
around the Mahabodhi temple.
The earlier Stupas being quite low and comparatively small so could well be decorated by
pious worshippers with festoons and garlands of flowers which were supported by the pegs. This
later on developed into a conventional representation of the festoons in plaster work over the
edifice and the pegs became purely ornamental. The rail in its primitive form was a simple fencing
made of wooden pillar with suchis fixed within lenticular sockets were later copied on stone turned
to be heavy and laborious speaks eloquently of its origin. The elaborate rail with decorations carved
on it came later, the gateways at the cardinal points being special ornamental feature as exemplified
in case of Bharhut and Sanchi.
The oldest example is the brick Stupa from Piprahwa near Nepal, has a height of only 22 ft
and a basal diameter of 116 ft. Whereas, the Sanchi Stupa which is of a later period is 54 ft high
with a basal diameter of 120 ft. The proportional height is just about half, while at Piprahwa it is
less than one-fifth (Longhurst 1992: 13). On this surmise the age of a Stupa may be determined
approximately from its shape and height, the earliest being a simple hemispherical, and the later
ones were lofty round brick tower standing on a high terraced platform.
With the size of the Stupas becoming huge and to economize the building material (brick or
stone) in some cases small compartments were made and filled with earth and rubble. The
foundation of the Stupa of south-eastern India is unique in its own kind e.g. Nagarjunakonda,
Ghantasala, Alluru etc, the structure was in a form of a wheel with a hub, spokes and a rim. In the
case of larger Stupas the spokes were further strengthen with additional walls and the space
between the spokes were filled with earth or a layer of concrete and earth. Another way which was
not very common was solid flooring above the earth-packing at regular intervals in the height
(Mitra 1980). The flooring was made either of bricks as found at Jaggayyapeta or of concrete as
found at Garikapadu.
The relic caskets were generally placed at the centre of the Stupa but in some instances like
in Nagarjunakonda the relic was kept far away from the centre and in Amravati five relic caskets
were found from the southern ayakas of the Stupa.
The drum of the Stupa also underwent changes; from the Kushana period onwards the medhi
portion became very elongated, leaving the anda portion look very short in height. The vedika with
cardinal projections approached by steps leading to them disappeared and for the first time such as
in Stupa-I of Sanchi during the Gupta period four images of Buddha were placed in cardinal
directions. The drum was no longer low, the height being considerably increased and the anda or
the cup-shaped part instead of retaining its primitive semi-circular contour bulged out above the
drum. This bulging is found even in the rock cut Stupas at Kanheri.
60
Simultaneously with the elongation of the medhi portion the discs of the chatra also
increased in number and appeared like a tall conical spire, sometimes crowned by a single chatra
and often tapering to a conical point (Mitra 1980: 30).
In most of the cases the upper portion of the harmika expanded, its facades relived with
offsets and recessed angles.
Gradually the platform becomes a permanent part of the Stupa to serve as a pedestal for the
medhi. Initially the shape used to be square or circular slowly the shape changed as can be seen in
the Stupa of Ratnagiri with the addition of multiple projections on each face of a square. In few
cases the platform grew higher, built in a form of diminishing terraces as in Lauriya-Nandangarh,
and often decorated with mouldings or sunken panels between the pilasters as seen in Andhra or
niches separated by pilasters as in Gandhara (Mitra 1980: 30).
Sometimes they were conventionally strained into fantastic curves in a most unnatural way
on either side. Sometime they form canopy over the Stupa.
The evolution of the torana (gateway) is equally interesting. The earlier type is found at
Amravati. The early gateways were a pair of pillars to which were tied the two ends of a torana
wreath. The earlier torana pillars must have had fresh torana wreaths tied to them every day. Later
heavy stone work took the place of wreath.
The four gateways were connected with railing round the Stupa which were sometimes
richly sculptured inside with scenes from the legends of Buddha in his various births, the outer side
showing only dwarf lotuses and half lotus medallions on the uprights (pillars) and cross bars
(suchis) and a long undulating flower garland on the coping (usnisha) and are available in Barhut,
Sanchi and Amravati railings.
According to Foucher (Foucher 1934: 51-52), the pseudo-flower garland and a long purse
full of coins appropriately issuing from the mouths of Yakshas (guardians of treasure) for the
benefit of the devotees. The plinth was also carved with representations of man running after
mythical animals.
Prof. Dubreuil (Jouveau-Dubreuil 1922) has nicely explained the decorative motifs of
Amravati Stupas. He divides them into three main divisions of the Stupa into smaller parts; first the
cylindrical part or the base is composed of two subordinate parts (a) the sculptured panel zone
below (b) the narrow frieze above. Second the hemispherical part is composed of (a) a range of
sculpture (b) a plain zone above (c) a decorated collar (d) a plain zone at the top.
On the top is the square part, the harmika which is balustrade around a central pillar of
imposing dimensions, besides which are the parasols/chatra.
The ayaka platform has projections at the cardinal points. There are five pillars on each
projection, square at the base then octagonal and finally round at the top. The platform is rather
narrow all along for the size of the Stupa.
61
After a detailed discussion on the various aspects of Stupa Architecture, a brief of some of
the main Stupas is done below for better understanding of the next chapter The Stupa Architecture
in Orissa
Vaisali
Vaisali located in Bihar was excavated from the year 1958-62 by B.P.Sinha and Sita Ram
Roy. This site yielded NBP ware and can be associated prior to Mauryan period. Vaisali was ruled
by the Lachchhavis, after the demise of Lord Buddha they too got a share of the relic of Buddha
and built a Stupa at Vaisali. This Stupa was rebuilt and enlarged several times; archaeologically it
has been proven that the Stupa was at least four times renovated and enlarged with bricks till 187
CE Initially the Stupa was just a heap of earth.
On the basis of the potteries reported from the site, the site can be dated back to 600 to 550
BCE. The earliest Stupas were small in size made up of layers of piled up mud. These piled up mud
layers were separated from each other with a thinner layer of kankar. The Stupa had ayaka
platform, most probably one each at cardinal directions, prototypes of the ayakas of the lower
Krishna valley. However only two of the ayaka platforms were found, of which only the southern
one was intact; measuring 1.52 m in length, 34 cm wide and 15 cm in height.
From the robbers trench a relics casket made of soapstone was reported. The excavators
opine that it is possible that Lachchhavis themselves might have dug this Stupa probably to build
more Stupas over the relics (Sinha and Roy 1969:22). The Stupa was build over a thick solid
platform. Around the platform at a lower level the floor was smoothened might be for the purpose
of circumambulation. During the third enlargement of the Stupa the flooring was paved with burnt
bricks. The Stupa was enlarged with burnt bricks during the early Mauryan period; the enlargement
was not uniform all around.
In the first quarter of the third century BCE the Stupa was badly eroded from the south-
western and north-western side, during the restoration work the diameter of the Stupa reduced from
10.46 m to 10.21 m. The Stupa was again enlarged in the second century BCE and now the
diameter of the Stupa increased to 11.63 m. Last time it was in first century CE when the Stupa was
restored after that it was left in debris.
Piprahwa
Piprahwa is situated in Basti district of U.P. this site can be dated back to fifth-fourth
century BCE. William Peppe an amateur archaeologist had dug the centre of the Stupa in 1897 and
found an inscribed relic casket. The inscription was in Ashokan Brahmi. The area from where he
obtained the relics fell in the second phase of the Stupa i.e. middle Mauryan period.
62
The site was only scientifically excavated in 1971 by K.M.Srivastav (IAR 1970-71:37). The
excavator believed that the Stupa had at least two structural phases. Initially the Stupa was an
earthen mound encircled by a single line of burnt bricks. Two relic caskets were unearthed from the
Stupa. The relic caskets are believed to be of Pre-Mauryan period.
When the Stupa was enlarged the anda of the mud Stupa was totally removed possibly as it
might have got washed off due to rain and other environmental hazards. This renovation work
started with a square base of burnt bricks. It contained rectangular niches at regular intervals for
bearing images.
As at the centre of the Stupa there was a pipe like hole Peppe described it as a circular pipe,
same kind of a hole was found in the Stupas of Bhattiprolu in Andhra Pradesh the site was
investigated by an engineer named Norris in 1871 in his report he mentioned it a shaft of the chatra
(Irwin 1979:811-812). Similar kind of hole at the centre was found at Lauriya-Nandangarh, a
wooden stump penetrated till the virgin soil was found (Irwin 1979:816). This finding made it clear
that a wooden pillar was placed at the centre of some of the ancient Stupas. Vaisali, Ghantasala and
Gotihawa are few other sites from where the axial pillars are reported.
In Cylone also this kind of axial pillar was reported but of stone and traditionally it was
known as Indra-kila which means Indras peg. When the local monks were asked why it is called
so, they couldnt answer.
Different scholars have different opinion; according to D.Mitra (1981:26) The pipe was
probably meant for marking the centre of the dome in order to facilitate the laying of brick courses
in circular rings, according to Irwin Stability was expressed by a stump or wooden shaft as the
axial pillar in the centre of the monument, so does Paul Mus Henceforth, the central part played
by the axial pillar in the structure of the Stupa is confirmed. It is not just that it marks the centre,
and that it rises up and dominates the Stupa in the form of a staff bearing parasols: the entire
masonry surrounds and encloses it, is explained by it, and constitutes no more than in a single
word its envelope. From the above discussion, it is clear that a Stupa is to be understood above
all in terms of its axis (Tucci 1988: xxiv). In the Tibetan tradition, the axial pole of the Stupa is
considered as the Tree of Life (Irwin 1979:839).
Sanchi
The Stupa-I at Sanchi (Plate- III) is said to be built during the time of Ashoka in a form of a
brick mound veneered with dressed stone. In the second century BCE the Stupa was enlarged in a
form of a high circular medhi with a circumambulation passage at the ground level surrounded by
railing pillars, that consists of a stambha connected with three suchis crowned by usnisha (coping
stone) and a balustrade stairway on the south was build for the purpose of circumambulation
around the anda portion. A huge hemispherical anda followed by harmika within a square railing
63
crowned by three superimposed chatras. There were four entrances on the four sides, formed by L-
shaped projections of the railing.
After a century in front of all the four entrance, beautifully and intricately carved torana
(gateway) were installed. The torana is engraved with the images of horse and elephant riders,
yakshas, tri-ratna and dharmachakra symbols. The Stupas build immediately before and after the
Christian era in northern and central India are quite similar to Stupa-I of Sanchi. The balustrades
and the torana were not the common feature of all the Stupas. Like in Stupa-II of second century
BCE at Sanchi has four entrances formed of the L-shaped extensions of the quadrants of the
balustrades without a torana, while the Stupa-III belonging to the first century CE consists of only
one torana. The Stupa at Bharhut was embellished with stambha and suchi at the ground level and
toranas on cardinal directions, but the torana are not as richly carved as that of Stupa-I of Sanchi.
The harmika constructed over the dome of the Stupa which bore on its crown the chatra, has
been reconstructed since in spite of beaming best preserved Stupa its harmika had been disappeared
due to wear and tear of the ages.
Dharmarajika Stupa
Dharmarajika Stupa at Taxila was excavated by Sir John Marshall in between 1913-14 CE.
The complex consists of the Dharmarajika Stupa with its surrounding shrines. This Stupa is the
most important Buddhist edifice in Taxila and is likely one of the earliest. The nucleus of the Stupa
goes back to the days of Ashoka. The name Dharmarajika itself suggests that Ashoka was
associated with the construction of the original Stupa. It underwent several restorations and
reconstructions until the last days of Buddhism in Taxila. Despite the damages it is still an
impressive structure, with a height of 14 meters and a diameter of 35 meter. There is a raised
terrace around the base that was used as a pradakshina patha, four flights of steps head up to the
terrace, one at each cardinal point. The core of the of the Stupa is filled with rubble and there are
sixteen interior supporting walls which radiate from the centre (wheel shaped). Unfortunately no
relic was found inside the Stupa.
Long before systematic excavation was undertaken, the dome of the Stupa was found open
from the top and whatever precious objects and relics that had been enshrined were removed by the
treasure hunters. To the north-east of the Stupa is a oblong shaped building thought to be a
Bodhisattavas shrine, near the back wall of the shrine, about 30 cm below the original floor,
Marshall found a vase shaped casket of grey micaceous schist that contained a silver vase inside.
The silver vase held a silver scroll and a small gold casket containing bone fragments. The
inscription of the scroll, in Kharoshti script and dated back to the year 136 of Azes (78 CE) states
that these relics were those of the Buddha and were enshrined by a devotee called Urusaka, a
64
Bactrian. These bone relics of Buddha concealed for almost two millennia in a forgotten shrine are
regarded as one of the most significant finds at Taxila. (Marshall 1951: 256-57)
The translation is as follows:
In the year 136 of Azes, on the fifteenth day of the month of ashada, on this day relic as of
the bless one were enshrined by Urasaka, scion of Imtavhria, a Bactrian, resident of the town of
Noacha.
These relics of the blessed one were enshrined Bodhisattava shrine at the Dharmarajika
Stupas at Taxila, for the bestowal of health upon the great kings, king of kings, the son of god
(devaputrasa), the Kushan, in honour of all Buddha, pratyeka Buddhas, Arhatas, all sentient
beings, parents, friends, advisors, kinsmen and blood relations for the bestowal of health upon
himself.
May thy right munificent gift lead to nirvana.
Nagarjunakonda
Nagarjunakonda is located in Palnad Taluk of the Guntur district, Andhra Prasedh in South
India. It was a secluded valley about 23 sq km in area and was surrounded on three sides by a
group of hills which were off shoots of the Nallamalai range. The river Krishna flowed in the
northeast associated with the celebrated teacher Nagarjuna of second century CE.
A.H. Longhurst, the then superintendent of the A.S.I, conducted full scale excavation from
1927-31; most of the monuments at the site was constructed in third-fourth century CE. During the
reign of the kings of the Ikshvaku dynasty remains of more than thirty Buddhist establishments
were found.
The great Stupa is the oldest and most central sacred monument at Nagarjunakonda.
Inscription date the Stupa around 246 CE but archaeologist believed that the Stupa could be older
i.e. earlier to 246 CE The complex was built by Charntamula, and mother-in-law of the second king
Virapurushadatta.
The great Stupa is one of the largest structures in the city of Vijayapuri. It has a diameter of
28m but its original height is not known as the upper part of the Stupa had been destroyed. The
Stupa is made of bricks and its interior is not solid brick work but consist of a system of walls
arranged in the form of a wheel, with a rim and spoke radiating from a central hub because of its
large size, additional support was given by adding two further concentric ring around the central
core. The design of concentric and radial walls forms three rows of cells in the interior of the Stupa
(eight in the inner, sixteen each in the middle and outer). The external surface of the Stupa was
coated with a plaster of lime. A.H.Longhurt in 1929 made a significant discovery of bone relics
paled in a gold reliquary with a few gold flowers, pearls and pieces of garnet and crystal kept inside
65
a silver casket in one of the outer most north-western cells. An inscription at the site states that this
is the great Stupa of the blessed one, hence archaeologist infer that the bone relics are those of the
Buddha.
Both the sets of Buddhas bone relics found from Taxila and Nagarjunakonda were presented
by the Director General A.S.I to the Mahabodhi Society in 1931 for their safe custody and
veneration and thus enshrined within the newly constructed Mulagan Kuti Vihara at Sarnath, since
corporeal relics of the Buddha are highly venerated by the Buddhists as they are seen as symbol of
the Buddhas presence.
Sarnath
Located in Uttar Pradesh is situated at a distance of 8 km from Varanasi Cant railway station.
Sarnath is a most holy place for Buddhist as Buddha preached his first sermon here (Rishipatana)
and expounded four noble truths.
Ashoka, the great Mauryan ruler started significant constructions at the spot where Buddha
had turned the wheel of law in motion and constructed the great Dharmarajika Stupa about 30.4 mt
high which was crowned at its top by a monolithic railing, some shrines along with the creation of
the monolithic pillar topped by the famous lion capital. In 1794 CE one Jagat Singh of Varanasi
pulled down the Dharmarajika Stupa for collection of raw materials and in due course a reliquary
within a stone box came to light but was thrown in the Ganges by him. The original structure raised
by Ashoka was 13.49 meter in diameter with brick size (49.5x36.8x6.4cm) and wedge shaped
(41.9x31.7x8.8cm).
Cunningham measured Dhameka Stupas diameter at the base is 93 feet and its height 110 feet.
It is a solid cylindrical tower, 28.50 meters in diameter at the base and 33.53 meter in height. The
structure consists of a circular stone drum to a height of 11.20 meters resting on the ground without
the usual rectangular basement. Above the drum rises the cylindrical mass of brick work. Halfway
up the base are existing eight niches in regular intervals which must have held images. Immediately
below them runs a broad course of elaborate carvings with geometrical and floral patterns
combined with birds and human figures of Gupta style on grey sand stone. This large scale surface
decoration shows the high achievement of Gupta workmanship in designing most intricate scroll
pattern. It is not unlikely that it marks the spot of the preaching of the Dharma by the Buddha.
Chaukhandi Stupa
It is a lofty brick structure, the central walls of the three successive terraces were provided
with niches for statuary. An image of Buddha seated in dharmacharkra mudra, a Bodhisattava and
two beautifully carved bas reliefs of Gupta style indicates that the monument existed in the Gupta
66
period as a terraced temple. The octagonal tower on top is a Mughal monument built in 1588 to
commemorate Humanyus visit to this place.
The next important commemorative Stupa constructed at Nalanda in honour of Sariputra.
During the day of Mauryans, Ashoka and subsequently in the Gupta period it turned into a huge
monastery complex later well known as university of Nalanda. The ruins of the Ancient Buddhist
establishments of Nalanda lie close to the village of Bargaon, south-east of Patna and north of
Rajagriha. The temples were constructed on the west facing east and the monasteries on the east
faces west. The main temple (temple No-3) standing at the southern extremity is the largest and
most imposing structure. This temple is a huge solid structure standing in the middle of a court
surrounded by a number of small votive Stupas.
During excavation it was found that the very small original structure was enlarged by later
reconstructions and renovations build over and around the ruins of the earlier ones, the present
mound being the result of seven successive recapitulations. The fifth of these successively built
temples is the most interesting and best preserved. It had four corner towers of which three have
been exposed and was found decorated with rows of niches containing well-modelled stucco
figures of Buddha and deities of Buddhist pantheon are fine specimens of Gupta art.
As the structure increased in size with each addition, the level of the court gradually rose and
many small votive Stupas are found at several places, completely or partly buried under the
different floors and walls that have been exposed.
The eastern part of India comprising of Magadha and Bengal yielded many Buddhist temples
side by side with the Stupas and monasteries viz; Bodhgaya temple, Nalanda Temple-3,12,13 and
14, Vikramsila complex with a lofty temple in the centre of a huge court surrounded by
monasteries cells all around , Paharpur in Bangladesh, Temples of Maynamati etc.
Thus with the passing away of time the structural activities of Buddhist Stupas of Barhut,
Sanchi, Amravati etc underwent changes and along with the constructions of Stupas, chaityas and
viharas. Buddhism flourished unabated till twelfth-thirteenth century CE.
The importance of Stupa as a sacred object of veneration continued in unbroken sequences and
large number of votive Stupas were constructed in large, medium and smaller dimensions on stone,
bricks including monolithic Stupas with images of Buddha and Buddhist divinites and also devoid
of images. The monolithic votive Stupas reported from Nalanda, Bodhgaya, Sarnath, Sanchi,
Orissa etc are forming a class by themselves for the study of the art, iconography and architecture
associated with Buddhism.
As already stated above magnificent temple building activities flourished in the Pala Empire
as exemplified in Nalanda (Temple No-3). Mahabodhi temple at Bodhgaya, central shrine at
Vikramsila are leaving behind a great legacy of Buddhist pursuits in art and architecture throughout
the length and breadth of the country.
67
*** ***