03002 R.M.

Young Wind Sentry Set

03101 R.M. Young Wind Sentry Anemometer
03301 R.M. Young Wind Sentry Vane
Revision: 9/13

C o p y r i g h t 1 9 8 6 - 2 0 1 3
C a m p b e l l S c i e n t i f i c , I n c .
Warranty
PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are
warranted by Campbell Scientific, Inc. (Campbell) to be free from defects in
materials and workmanship under normal use and service for twelve (12)
months from date of shipment unless otherwise specified in the corresponding
Campbell pricelist or product manual. Products not manufactured, but that are
re-sold by Campbell, are warranted only to the limits extended by the original
manufacturer. Batteries, fine-wire thermocouples, desiccant, and other
consumables have no warranty. Campbell's obligation under this warranty is
limited to repairing or replacing (at Campbell's option) defective products,
which shall be the sole and exclusive remedy under this warranty. The
customer shall assume all costs of removing, reinstalling, and shipping
defective products to Campbell. Campbell will return such products by surface
carrier prepaid within the continental United States of America. To all other
locations, Campbell will return such products best way CIP (Port of Entry)
INCOTERM 2010, prepaid. This warranty shall not apply to any products
which have been subjected to modification, misuse, neglect, improper service,
accidents of nature, or shipping damage. This warranty is in lieu of all other
warranties, expressed or implied. The warranty for installation services
performed by Campbell such as programming to customer specifications,
electrical connections to products manufactured by Campbell, and product
specific training, is part of Campbells product warranty. CAMPBELL
EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Campbell is not liable for any special, indirect,
incidental, and/or consequential damages.
Assistance
Products may not be returned without prior authorization. The following
contact information is for US and international customers residing in countries
served by Campbell Scientific, Inc. directly. Affiliate companies handle
repairs for customers within their territories. Please visit
www.campbellsci.com to determine which Campbell Scientific company serves
your country.

To obtain a Returned Materials Authorization (RMA), contact CAMPBELL

SCIENTIFIC, INC., phone (435) 227-9000. After an application engineer
determines the nature of the problem, an RMA number will be issued. Please
write this number clearly on the outside of the shipping container. Campbell
Scientific's shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____
815 West 1800 North
Logan, Utah 84321-1784

For all returns, the customer must fill out a "Statement of Product Cleanliness
and Decontamination" form and comply with the requirements specified in it.
The form is available from our web site at www.campbellsci.com/repair. A
completed form must be either emailed to repair@campbellsci.com or faxed to
(435) 227-9106. Campbell Scientific is unable to process any returns until we
receive this form. If the form is not received within three days of product
receipt or is incomplete, the product will be returned to the customer at the
customer's expense. Campbell Scientific reserves the right to refuse service on
products that were exposed to contaminants that may cause health or safety
concerns for our employees.
Table of Contents
PDF viewers: These page numbers refer to the printed version of this document. Use the
PDF reader bookmarks tab for links to specific sections.

1. Introduction .................................................................1

2. Cautionary Statements...............................................1

3. Initial Inspection .........................................................1

3.1 Ships With List.....................................................................................2

4. Quickstart ....................................................................2
4.1 Step 1 Mount the Sensor .................................................................2
4.2 Step 2 Use SCWin Short Cut to Program Datalogger and
Generate Wiring Diagram.................................................................5

5. Overview ......................................................................7

6. Specifications .............................................................8
6.1 Wind Speed (Anemometer)..................................................................8
6.2 Wind Direction (Vane).........................................................................9
6.3 Wind Sentry Assembly ........................................................................9

7. Installation ...................................................................9
7.1 Siting ....................................................................................................9
7.2 Assembly and Mounting ....................................................................10
7.2.1 03002 Wind Sentry Set ...............................................................10
7.2.2 03101 Anemometer.....................................................................10
7.2.3 03301 Vane .................................................................................11
7.3 Wiring ................................................................................................11
7.4 Programming......................................................................................13
7.4.1 Wind Speed.................................................................................13
7.4.2 Wind Direction............................................................................13
7.4.3 Wind Vector Processing Instruction ...........................................14
7.4.4 Example Programs ......................................................................14
7.4.4.1 CR1000 Program..............................................................15
7.4.4.2 CR10X Program...............................................................15
7.4.5 Long Lead Lengths .....................................................................17

8. Sensor Maintenance .................................................17

i
Table of Contents

9. Troubleshooting........................................................18
9.1 Wind Direction .................................................................................. 18
9.2 Wind Speed ....................................................................................... 18

10. References.................................................................19

Appendices

A. Wind Direction Sensor Orientation .......................A-1

A.1 Determining True North and Sensor Orientation ............................ A-1

B. Wind Direction Measurement Theory....................B-1

B.1 BRHalf Instruction .......................................................................... B-1
B.2 EX-DEL-SE (P4) Instruction........................................................... B-1

Figures
4-1. CM200-Series Crossarm with CM220 Right Angle Mounting
Bracket ............................................................................................. 3
4-2. 03002 mounted to CM200-Series Crossarm with CM220 .................. 4
4-3. 03002 mounted to CM200-Series Crossarm with pn 17953............... 4
7-1. The CM216 allows an 03002 or 03101 to mount atop the mast of
a CM110, CM115, or CM120 tripod ............................................. 10
7-2. 03101 mounted to a crossarm via a 1049 NU-RAIL ......................... 11
A-1. Magnetic declination for the contiguous United States (2004)........ A-2
A-2. Declination angles east of True North are subtracted from 0 to
get True North.............................................................................. A-3
A-3. Declination angles west of True North are added to 0 to get True
North ............................................................................................ A-3
B-1. 03002 and 03301 potentiometer in a half bridge circuit .................. B-1

Tables
5-1. Recommended Cable Lengths ............................................................. 7
7-1. 03002-L Wiring................................................................................. 12
7-2. 03101 and 03301 Wiring ................................................................... 12
7-3. Wind Speed Multiplier (With Pulse Channel Configuration Set to
Low Level AC, Output Hz) ........................................................ 13
7-4. Parameters for Wind Direction.......................................................... 14
7-5. Wiring for Example Programs using the 03002-L............................. 14

ii
R.M. Young Wind Sentry
1. Introduction
The 03002 Wind Sentry Set measures both wind speed and direction. It
consists of a 3-cup anemometer and a wind vane mounted on a small crossarm.
The anemometer (pn 03101) and vane (pn 03301) may be purchased
separately.

Before installing the 03002, please study

Section 2, Cautionary Statements

Section 3, Initial Inspection
Section 4, Quickstart

2. Cautionary Statements
The 03002 is a precision instrument. Please handle it with care.

If the 03002 is to be installed at heights over 6 feet, be familiar with tower

safety and follow safe tower climbing procedures.

Danger Use extreme care when working near overhead electrical wires.
Check for overhead wires before mounting the 03002 or before raising a
tower.

The black outer jacket of the cable is Santoprene rubber. This

compound was chosen for its resistance to temperature extremes, moisture,
and UV degradation. However, this jacket will support combustion in air.
It is rated as slow burning when tested according to U.L. 94 H.B. and will
pass FMVSS302. Local fire codes may preclude its use inside buildings.

3. Initial Inspection
Upon receipt of the 03002, inspect the packaging and contents for damage.
File damage claims with the shipping company. Immediately check
package contents against the shipping documentation (see Section 3.1,
Ships With List). Contact Campbell Scientific about any discrepancies.

The model number and cable length are printed on a label at the
connection end of the cable. Check this information against the shipping
documents to ensure the expected product and cable length are received.

1
R.M. Young Wind Sentry

3.1 Ships With List

The 03002 Wind Sentry ships with:

(1) 03002 Wind Sentry including

03102 anemometer
03302 vane
crossarm
band clamp (pn 4919)
(1) 12" x 1.0" unthreaded aluminium pipe (pn 3659)
(1) Allen wrench (pn 5201)

The 03101 anemometer ships with:

(1) 03101 anemometer

(1) 10" x 3/4" threaded galvanized pipe (pn 12243)
(1) Allen wrench (pn 5201)

The 03301 Vane ships with:

(1) 03301 vane

(1) 10 x 3/4 threaded galvanized pipe (pn 12243)
(1) Allen wrench (pn 5201)

4. Quickstart
4.1 Step 1 Mount the Sensor
This quick start is for the 03002 wind set. Refer to Section 7, Installation, if
installing just the 03101 anemometer or 03301 vane. Section 7, Installation,
also provides siting information.

Tools required:

5/64 Allen wrench

Allen wrench provided with sensor
1/2 open end wrench
compass and declination angle for the site (see Appendix A)
small screw driver provided with datalogger
UV resistant cable ties
small pair of diagonal-cutting pliers
6 10 torpedo level

Install the 03002 using:

Standard 1.0-in. IPS schedule 40 pipe (pn 3659)

CM220 Right-Angle Mounting Kit (FIGURE 4-1 and FIGURE 4-2),
or
17953 1 x 1 inch NU-RAIL Crossover Fitting (FIGURE 4-3)

2
 R.M. Young Wind Sentry

1. Install the cup wheel to the anemometer shaft using the Allen wrench
provided with the sensor.

2. Mount a CM202, CM204, or CM206 crossarm to the tripod or tower.

3. Orient the crossarm North-South, with the CM220 mount or 17953 NU-
RAIL on the north end. Appendix A contains detailed information on
determining True North using a compass and the magnetic declination for
the site.

4. Secure the 12 in. aluminum pipe to the CM220 mount or 17953 NU-RAIL.
The 3659 aluminum pipe is shipped with the 03002.

5. Place the 03002 on the pipe, and orient the sensor crossarm North-South
with the vane to the North.

6. Tighten the mounting post band clamp. Final sensor orientation is done
after the datalogger has been programmed to measure wind direction as
described in Appendix A.

7. Route the sensor cable along the underside of the crossarm to the tripod or
tower, and to the instrument enclosure.

8. Secure the cable to the crossarm and tripod or tower using cable ties.

CM220

CM200-Series Crossarm

FIGURE 4-1. CM200-Series Crossarm with CM220 Right Angle

Mounting Bracket

3
R.M. Young Wind Sentry

Alumimum Pipe

CM220

CM200-Series Crossarm

FIGURE 4-2. 03002 mounted to CM200-Series Crossarm with CM220

pn 17953 NU-RAIL
Aluminum Pipe

CM200-Series Crossarm
Cable Tie

FIGURE 4-3. 03002 mounted to CM200-Series Crossarm with

pn 17953

4
 R.M. Young Wind Sentry

4.2 Step 2 Use SCWin Short Cut to Program Datalogger

and Generate Wiring Diagram
The simplest method for programming the datalogger to measure the 03002 is
to use Campbell Scientific's SCWin Short Cut Program Generator.

1. Open Short Cut and click on New Program.

2. Select the Datalogger and enter the Scan Interval and select Next.

5
R.M. Young Wind Sentry

3. Select 03002 Wind Speed & Direction Sensor and select the right arrow
(in center of screen) to add it to the list of sensors to be measured then
select Next.

4. Select Wind Vector for the output and then select Finish.

6
 R.M. Young Wind Sentry

5. Wire according to the wiring diagram generated by Short Cut.

5. Overview
The 03002 Wind Sentry Set is used to measure horizontal wind speed and
direction.

Wind speed is measured with a three cup anemometer. Rotation of the cup
wheel produces an ac sine wave voltage with frequency proportional to wind
speed. This is a special version of the 03102 built for Campbell Scientific by
R.M. Young that has shielded bearings rather than sealed bearings. The
shielded bearings provide a lower starting threshold than sealed bearings.

Vane position is transmitted by a 10-k potentiometer. With a precision

excitation voltage applied, the output voltage is proportional to wind direction.

The 03101 Anemometer and 03301 Vane can be ordered as separate sensors,
which are also covered in this manual. These two sensors combined differ
from the 03002 only by the absence of a junction box. The R.M. Young
Instruction Manual includes additional information on the operating principles,
installation, and maintenance of the sensor.

Cable length for the Wind Sentry is specified when the sensor is ordered.
TABLE 5-1 gives the recommended lead length for mounting the sensor at the
top of the tripod/tower with a CM200-series crossarm.

TABLE 5-1. Recommended Cable Lengths

CM106 CM110 CM115 CM120 UT10 UT20 UT30

12 ft 15 ft 20 ft 25 ft 15 ft 25 ft 38 ft

7
R.M. Young Wind Sentry

The 03002's cable can terminate in:

Pigtails that connect directly to a Campbell Scientific datalogger

(option PT).

Connector that attaches to a prewired enclosure (option PW). Refer

to www.campbellsci.com/prewired-enclosures for more information.

Connector that attaches to a CWS900 Wireless Sensor Interface

(option CWS). The CWS900 allows the 03002 to be used in a
wireless sensor network. Refer to www.campbellsci.com/cws900 for
more information.

6. Specifications
Features:

Designed for continuous, long term, unattended operation in adverse

conditions

Small size, simplicity, and rugged construction provide a quality

instrument for a modest price

Ideal for wind profile studies

Compatible with the LLAC4 4-channel Low Level AC Conversion

Module, which increases the number of anemometers one datalogger
can measure

Campbell Scientific version uses shielded bearings, which lowers the

anemometer's starting threshold

Compatible
Dataloggers: CR200(X)-series
CR800 series
CR1000
CR3000
CR5000
CR510
CR10(X)
CR23X
CR7
21X

6.1 Wind Speed (Anemometer)

Range: 0 to 50 m s1 (112 mph), gust survival 60 m s1 (134
mph)
Sensor: 12 cm diameter cup wheel assembly, 40 mm
diameter hemispherical cups
Accuracy: 0.5 m s1 (1.1 mph)
Turning Factor: 75 cm (2.5 ft)
Distance Constant
(63% recovery): 2.3 m (7.5 ft)

8
 R.M. Young Wind Sentry

Threshold: 0.5 m s1 (1.1 mph)

Transducer: Stationary coil, 1300 ohm nominal resistance
Output: AC sine wave signal induced by rotating magnet on
cup wheel shaft
100 mV peak-to-peak at 60 rpm; 6 V peak-to-peak
at 3600 rpm
Output Frequency: 1 cycle per cup wheel revolution; 0.75 m s1 per Hz
Cup Wheel Diameter: 12 cm (4.7 in)
Weight: 113 g (4 oz)

6.2 Wind Direction (Vane)

Range: 360 mechanical, 352 electrical (8 open)
Sensor: Balanced vane, 16 cm turning radius
Accuracy: 5
Damping Ratio: 0.2
Delay Distance
(50% recovery): 0.5 m (1.6 ft)
Threshold: 0.8 m s1 (1.8 mph) at 10 displacement
(1.8 m s1 (4 mph) at 5 displacement)
Transducer: Precision conductive plastic potentiometer;
10 k resistance; 1.0% linearity; life expectancy 50
million revolutions
Rated 1 W at 40C, 0 W at 125C
Transducer Excitation
Requirement: Regulated dc voltage, 15 Vdc max
Output: Analog dc voltage proportional to wind direction
angle with regulated excitation voltage supplied by
the datalogger
Vane Length: 22 cm (8.7 in)
Vane Weight: 170 g (6 oz)

6.3 Wind Sentry Assembly

Operating Temperature: 50 to +50C assuming non-riming conditions
Overall Height: 32 cm (12.6 in)
Crossarm Length: 40 cm (15.7 in) between instruments (center-to-
center)
Mounting Diameter: 34 mm (1.34 in), mounts on standard 1 in. IPS pipe

7. Installation
7.1 Siting
Locate wind sensors away from obstructions (e.g. trees and building). As a
general rule of thumb, there should be a horizontal distance of at least ten times
the height of the obstruction between the wind set and the obstruction. If it is
necessary to mount the sensors on the roof of a building, the height of the
sensors above the roof, should be at least 1.5 times the height of the building.
See Section 10, References, for a list of references that discuss siting wind
speed and direction sensors.

9
R.M. Young Wind Sentry

7.2
.2 Assembly and Mounting
Tools required:
5/64 Allen wrench
Allen wrench provided with sensor
1/2 open end wrench
compass and declination angle for the site (see Appendix A)
small screw driver provided with datalogger
UV resistant cable ties
small pair of diagonal-cutting pliers
6 - 10 torpedo level

7.2.1 03002 Wind Sentry Set

The 03002 mounts to a standard 1.0 in. IPS schedule 40 pipe (1.34 in. O.D.).
A 12 long mounting pipe ships with the 03002. The mounting pipe typically
fastens to a CM200-series crossarm via the CM220 mount or 17953 NU-RAIL
fitting. Section 4, Quickstart, describes mounting the 03002 using a CM220
mount or a 17953 NU-RAIL fitting. The 03002 can also be mounted at the top
of a CM110, CM115, or CM120 tripod with the CM216 (see FIGURE 7-1).

Fits in Mast

FIGURE 7-1. The CM216 allows an 03002 or 03101 to mount atop the
mast of a CM110, CM115, or CM120 tripod

7.2.2 03101 Anemometer

Install the cupwheel to the anemometer shaft using the Allen wrench provided
with the sensor.

The 03101 mounts to a threaded 0.75 in. IPS schedule 40 pipe (1.05 in. O.D.).
A 10 in. long mounting pipe ships with the 03101. The mounting pipe
typically fastens to a CM200-series crossarm via the CM220 mount (see
FIGURE 4-1 in Quickstart) or 1049 NU-RAIL fitting (FIGURE 7-2). The

10
 R.M. Young Wind Sentry

03101 can also be mounted at the top of a tripod using the CM216 (see
FIGURE 7-1).

Mount the CM200-series crossarm to the tripod or tower. Screw the mounting
pipe into the base of the 03101, and attach the sensor / mounting pipe to the
crossarm.

Route the sensor cable along the underside of the crossarm to the tower/tripod
mast, and to the instrument enclosure. Secure the sensor cable to the crossarm
and mast using cable ties.

Cable Tie

Crossarm

1049 NU-RAIL Fitting

FIGURE 7-2. 03101 mounted to a crossarm via a 1049 NU-RAIL

7.2.3 03301 Vane

The 03301 vane is typically ordered as a replacement vane for the 03002 Wind
Sentry Set, and includes the bracket for attaching it to the 03002 small
crossarm. Part number 4913 pipe mount (not included with the sensor) can be
used to attach the 03301 to a CM200-series crossarm (with the CM220 or pn
1049), and the mounting pipe that ships with the sensor.

7.3 Wiring
Connections to Campbell Scientific dataloggers are given in TABLE 7-1 and
TABLE 7-2. When Short Cut is used to create the datalogger program, the
sensor should be wired to the channels shown on the wiring diagram created by
Short Cut.

11
R.M. Young Wind Sentry

TABLE 7-1. 03002-L Wiring

CR800
CR5000 CR21X
CR3000 CR510 CR7
Color Description CR1000 CR10(X) CR23X CR200(X)
Red Wind Spd. Signal Pulse Pulse Pulse P_LL
Black Wind Spd. Reference G
Clear Shield G
White Wind Dir. Reference AG
Green Wind Dir. Signal SE Analog SE Analog SE Analog SE Analog
Blue Wind Dir. Excitation Excitation Excitation Excitation Excitation

TABLE 7-2. 03101 and 03301 Wiring

CR800
CR5000 CR21X
CR3000 CR510 CR7
Color Description CR1000 CR10(X) CR23X CR200(X)
Black Wind Spd. Signal Pulse Pulse Pulse P_LL
White Wind Spd. Reference G
Clear Wind Spd. Shield G

Red Wind Dir. Signal SE Analog SE Analog SE Analog SE Analog

Black Wind Dir. Excitation Excitation Excitation Excitation Excitation
White Wind Dir. Reference AG
Clear Wind Dir. Shield G

Wind Speed 03101 Wind Direction 03301

12
 R.M. Young Wind Sentry

7.4 Programming
This section is for users who write their own programs. A datalogger program
to measure this sensor can be created using Short Cut. You do not need to read
this section to use Short Cut.

7.4.1 Wind Speed

Wind speed is measured with the Pulse Count instruction (PulseCount() in
CRBasic and Instruction 3 in Edlog). Use the low level AC configuration.
For dataloggers programmed with Edlog, specify configuration code 21 to
output frequency in hertz.

The expression for wind speed (U) is:

U = MX + B
where
M = multiplier
X = number of pulses per second (Hertz)
B = offset

TABLE 7-3 lists the multipliers (M) and offsets (Off) to obtain meters/second
or miles/hour when the Pulse Count instruction is configured to output the
result in hertz.

TABLE 7-3. Wind Speed Multiplier

(With Pulse Channel Configuration Set to Low Level AC, Output Hz)

Model Meters/Second Miles/Hour

03002 / 03101 M = 0.750 M = 1.677
Off = 0.2 Off = 0.4
*When the pulse channel configuration is set to Low Level AC, output
counts, the multiplier above is divided by the execution interval in seconds.

7.4.2 Wind Direction

The wind vane is coupled to a 10 k potentiometer, which has a 8 degree
electrical dead band between 352 and 360 degrees.

The CR200(X) dataloggers use the ExDelSE() instruction to measure wind

direction. All other CRBasic dataloggers use the BRHalf() instruction. Edlog
dataloggers (CR510, CR10X, CR23X) use Edlog Instruction 4Excite, Delay
(P4).

Excitation voltages, range codes, and multipliers for Campbell Scientific

dataloggers are listed in TABLE 7-4. Appendix B has additional information
on the BRHalf() measurement instructions.

13
R.M. Young Wind Sentry

TABLE 7-4. Parameters for Wind Direction

CR10(X) CR7
CR510 21X CR800 CR5000
CR200(X) CR23X CR1000 CR3000
Measurement 2500 mV, 5000 mV, 2500 mV, 5000 mV,
Range slow slow/60 Hz 60 Hz, 60 Hz,
reverse reverse
excitation excitation
Excitation 2500 mV 5000 mV 2500 mV 5000 mV
Voltage
Multiplier 0.1408 0.0704 352 352
Offset 0 0 0 0

7.4.3 Wind Vector Processing Instruction

The Wind Vector output instruction is used to process and store mean wind
speed, unit vector mean wind direction, and standard deviation of the wind
direction (optional) from the measured wind speed and direction values.

7.4.4 Example Programs

The following programs measure the 03002 every 5 seconds, and store mean
wind speed, unit vector mean direction, and standard deviation of the direction
every 60 minutes. Wiring for the examples is given in TABLE 7-5.

TABLE 7-5. Wiring for Example Programs

using the 03002-L

Color Description CR1000 CR10X

Red Wind Spd. Signal P1 P1
Black Wind Spd. Reference G
Clear Wind Spd. Shield G

Green Wind Dir. Signal SE 1 SE 1

Blue Wind Dir. Excitation VX 1 or E1
EX 1
White Wind Dir. Reference AG

14
 R.M. Young Wind Sentry

7.4.4.1 CR1000 Program

'CR1000
'Declare Variables and Units
Public Batt_Volt
Public WS_ms
Public WindDir

Units Batt_Volt=Volts
Units WS_ms=meters/second
Units WindDir=Degrees

'Define Data Tables

DataTable(Table1,True,-1)
DataInterval(0,60,Min,10)
WindVector (1,WS_ms,WindDir,FP2,False,0,0,0)
FieldNames("WS_ms_S_WVT,WindDir_D1_WVT,WindDir_SD1_WVT")
EndTable

'Main Program
BeginProg
Scan(5,Sec,1,0)
'Default Datalogger Battery Voltage measurement Batt_Volt:
Battery(Batt_Volt)

'03002 or 03101 RM Young Wind Sentry Wind Speed Sensor measurement - WS_ms:
PulseCount(WS_ms,1,1,1,1,0.75,0.2)
If WS_ms<0.21 Then WS_ms=0

'03002 or 03301 RM Young Wind Sentry Wind Direction Sensor measurement -

WindDir:
BrHalf(WindDir,1,mV2500,1,1,1,2500,True,0,_60Hz,352,0)
'Use mV5000 range and 5000 mV excitation for CR3000 and CR5000 dataloggers.
If WindDir>=360 OR WindDir<0 Then WindDir=0

'Call Data Tables and Store Data

CallTable(Table1)
NextScan
EndProg

7.4.4.2 CR10X Program

;{CR10X}
*Table 1 Program
01: 5.0000 Execution Interval (seconds)

1: Batt Voltage (P10)

1: 1 Loc [ Batt_Volt ]

;03002 or 03101 RM Young Wind Sentry Wind Speed Sensor measurement - WS_ms:
2: Pulse (P3)
1: 1 Reps
2: 1 Pulse Channel 1
3: 21 Low Level AC, Output Hz
4: 2 Loc [ WS_ms ]
5: 0.75 Multiplier
6: 0.2 Offset

15
R.M. Young Wind Sentry

;If WS < starting threshold then set WS = 0

3: If (X<=>F) (P89)
1: 2 X Loc [ WS_ms ]
2: 4 <
3: 0.21 F
4: 30 Then Do

4: Z=F x 10^n (P30)

1: 0 F
2: 0 n, Exponent of 10
3: 2 Z Loc [ WS_ms ]

5: End (P95)

;03002 or 03301 RM Young Wind Direction Sensor measurement - WindDir:

6: Excite-Delay (SE) (P4)
1: 1 Reps
2: 5 2500 mV Slow Range ;5000 mV(slow/60hz) range for CR23X, 21X, or CR7
3: 1 SE Channel
4: 1 Excite all reps w/Exchan 1
5: 2 Delay (0.01 sec units)
6: 2500 mV Excitation ;5000 mV for CR23X, 21X, or CR7
7: 3 Loc [ WindDir ]
8: 0.1408 Multiplier ;0.0704 for CR23X, 21X, or CR7
9: 0 Offset

7: If (X<=>F) (P89)
1: 3 X Loc [ WindDir ]
2: 3 >=
3: 360 F
4: 30 Then Do

8: Z=F x 10^n (P30)

1: 0 F
2: 0 n, Exponent of 10
3: 3 Z Loc [ WindDir ]

9: End (P95)

10: If (X<=>F) (P89)

1: 3 X Loc [ WindDir ]
2: 4 <
3: 0 F
4: 3 Then Do

11: Z=F x 10^n (P30)

1: 0 F
2: 0 n, Exponent of 10
3: 3 Z Loc [ WindDir ]

12: End (P95)

13: If time is (P92)

1: 0 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)

16
 R.M. Young Wind Sentry

14: Set Active Storage Area (P80)^15464

1: 1 Final Storage Area 1
2: 101 Array ID

15: Real Time (P77)^6687

1: 1220 Year,Day,Hour/Minute (midnight = 2400)

16: Wind Vector (P69)^28601

1: 1 Reps
2: 0 Samples per Sub-Interval
3: 0 S, theta(1), sigma(theta(1)) with polar sensor
4: 2 Wind Speed/East Loc [ WS_ms ]
5: 3 Wind Direction/North Loc [ WindDir ]

7.4.5 Long Lead Lengths

When sensor lead length exceeds 100 feet, the settling time allowed for the
measurement of the vane should be increased to 20 milliseconds.

For dataloggers programmed with Edlog (and the CR200(X)), the EX-DEL-SE
(P4) measurement instruction should be used. Enter a 2 in the P4 Delay
parameter for a 20 millisecond delay.

For dataloggers programmed with CRBasic, increase the Settling Time

parameter of the BRHalf() instruction to 20 milliseconds (20,000
microseconds).

CAUTION The 60 Hz rejection option can not be used with the DC

Half Bridge instruction, when the delay is not zero. Do not
use long lead lengths in electrically noisy environments.

8. Sensor Maintenance
Every month do a visual/audio inspection of the anemometer at low wind
speeds. Verify that the cup assembly and wind vane rotate freely. Inspect the
sensor for physical damage.

Replace the anemometer bearings when they become noisy, or the wind speed
threshold increases above an acceptable level. The condition of the bearings
can be checked with a paper clip as described in the R.M. Young manual.

The potentiometer has a life expectancy of fifty million revolutions. As it

becomes worn, the element can produce noisy signals or become nonlinear.
Replace the potentiometer when the noise or nonlinearity becomes
unacceptable.

Contact Campbell Scientific for a Return Materials Authorization (RMA)

number at (435) 227-9000. A Statement of Product Cleanliness and
Decontamination form also needs to be filled out.

17
R.M. Young Wind Sentry

9. Troubleshooting
9.1 Wind Direction
Symptom: NAN, 9999, or no change in direction

1. Check that the sensor is wired to the excitation and single-ended channel
specified by the measurement instruction.

2. Verify that the excitation voltage and range code are correct for the
datalogger type.

3. Disconnect the sensor from the datalogger and use an ohm meter to check
the potentiometer. Resistance should be about 10 k between the black
and white wires. The resistance between either the black/red or white/red
wires for the 03301 and blue/red or white/red for the 03002 should vary
from 1 k to 11 k depending on vane position. Resistance when the
vane is in the 8 degree dead band should be about 1 M.

Symptom: Incorrect wind direction

1. Verify that the excitation voltage, range code, multiplier, and offset
parameters are correct for the datalogger type.

2. Check orientation of sensor as described in Section 4.1, Step 1 Mount

the Sensor.

9.2 Wind Speed

Symptom: No wind speed

1. Check that the sensor is wired to the pulse channel specified by the pulse
count instruction.

2. Disconnect the sensor from the datalogger and use an ohm meter to check
the coil. The resistance between the white and black wires for the 03101
and black and red wires for the 03002 should be a nominal 1300 ohms.
Infinite resistance indicates an open coil; low resistance indicates a
shorted coil.

3. Verify that the configuration code, and multiplier and offset parameters
for the pulse count instruction are correct for the datalogger type.

Symptom: Wind speed does not change

1. For the dataloggers that are programmed with Edlog, the input location
for wind speed is not updated if the datalogger is getting Program Table
Overruns. Increase the execution interval (scan rate) to prevent overruns.

18
 R.M. Young Wind Sentry

10. References
The following references give detailed information on siting wind speed and
wind direction sensors.

EPA, 1989: Quality Assurance Handbook for Air Pollution Measurements

System, Office of Research and Development, Research Triangle Park, NC,
27711.

EPA, 1987: On-Site Meteorological Program Guidance for Regulatory

Modeling Applications, EPA-450/4-87-013, Office of Air Quality Planning and
Standards, Research Triangle Park, NC 27711.

The State Climatologist, 1985: Publication of the American Association of

State Climatologists: Height and Exposure Standards, for Sensors on
Automated Weather Stations, vol. 9, No. 4.

WMO, 1983: Guide to Meteorological Instruments and Methods of

Observation, World Meteorological Organization, No. 8, 5th edition, Geneva,
Switzerland.

19
R.M. Young Wind Sentry

20
Appendix A. Wind Direction Sensor
Orientation
A.1 Determining True North and Sensor Orientation
Orientation of the wind direction sensor is done after the datalogger has been
programmed, and the location of True North has been determined. True North is
usually found by reading a magnetic compass and applying the correction for
magnetic declination; where magnetic declination is the number of degrees
between True North and Magnetic North. The preferred method to obtain the
magnetic declination for a specific site is to use a computer service offered by
NOAA at www.ngdc.noaa.gov/geomag. Magnetic declination can also be
obtained from a map or local airport. A general map showing magnetic
declination for the contiguous United States is shown in FIGURE A-1.

Declination angles east of True North are considered negative, and are subtracted
from 360 degrees to get True North as shown FIGURE A-2 (0 and 360 are the
same point on a compass). Declination angles west of True North are considered
positive, and are added to 0 degrees to get True North as shown in FIGURE A-3.
For example, the declination for Logan, Utah is 14 East. True North is 360 -
14, or 346 as read on a compass.

Orientation is most easily done with two people, one to aim and adjust the
sensor, while the other observes the wind direction displayed by the datalogger.

1. Establish a reference point on the horizon for True North.

2. Sighting down the instrument center line, aim the nose cone, or
counterweight at True North. Display the input location or variable for wind
direction using a hand-held keyboard display, PC, or laptop.
3. Loosen the U-bolt on the CM220 or the set screws on the NU-RAIL that
secure the base of the sensor to the crossarm. While holding the vane
position, slowly rotate the sensor base until the datalogger indicates 0
degrees. Tighten the set screws.

A-1
Appendix A. Wind Direction Sensor Orientation

FIGURE A-1. Magnetic declination for the contiguous United States

(2004)

A-2
 Appendix A. Wind Direction Sensor Orientation

FIGURE A-2. Declination angles east of True North are subtracted

from 0 to get True North

FIGURE A-3. Declination angles west of True North are added to 0 to

get True North

A-3
Appendix A. Wind Direction Sensor Orientation

A-4
Appendix B. Wind Direction
Measurement Theory
It is not necessary to understand the concepts in this section for the general
operation of the 03002 with Campbell Scientifics datalogger.

EXCITATION VOLTAGE (Vx)

Rt
SIGNAL + (Vs)
Rs
AZIMUTH REFERENCE

EARTH GROUND CONNECTION

FIGURE B-1. 03002 and 03301 potentiometer in a half bridge circuit

B.1 BRHalf Instruction

The BRHalf() instruction outputs a precise excitation voltage (Vx), and
measures the voltage between the wiper and ground (Vs). The resistance
between the wiper and ground, Rs, and Vs varies with wind direction. The
measurement result is the ratio of the measured voltage to the excitation
voltage (Vs/Vx). This ratio is related to the resistance as shown below:

Vs V x = Rs (Rt + Rs )

The maximum value that Rs will reach is Rf, just before it crosses over from the
west side of north to the east side of north (at this point Rt = 0). Vs / Vx reaches
its maximum value of 1.0 mV/mV at 352 degrees. The multiplier to convert
Vs/Vx to degrees is 352 degrees / 1.0 Vs/Vx = 352. Since the datalogger outputs
the ratio Vs / Vx, the multiplier is the same for both the CR10(X) and CR3000,
even though they use a different excitation voltage. See Section 13.5 in the
CR10X manual, Section 4.3 in the CR1000 manual, or Section 3.5 in the
CR3000 manual for more information on the bridge measurements.

B.2 EX-DEL-SE (P4) Instruction

Instruction 4 outputs a precise excitation voltage (Vx) and measures the voltage
between the wiper and analog ground, Vs. The resistance between the wiper
and analog ground, Rs, and Vs varies with wind direction. Instruction 4 outputs
the measured voltage, Vs. This measured voltage is related to resistance as
shown below:

Vs = Vx Rs (Rt + Rs )

B-1
Appendix B. Wind Direction Measurement Theory

The maximum value that Rs will reach is Rf just before it crosses over from the
west side of north to the east side of north (at this point Rt = 0). Vs reaches its
maximum value of Vx. This maximum voltage equals 2500 mV for an
excitation voltage of 2500 mV recommended for the CR10(X) and 5000 mV
for an excitation voltage of 5000 mV recommended for the CR23X at 352
degrees. The multiplier to convert Vs to degrees is 352 degrees / 2500 mV =
0.1408 for the CR10X, or, 352 degrees / 5000 mV = 0.0704 for the CR23X.
See Section 13.5 in the datalogger manual from more information on the bridge
measurements.

B-2
 METEOROLOGICAL INSTRUMENTS

INSTRUCTIONS

WIND SENTRY
MODEL 03002-5

R.M. YOUNG COMPANY 2801 AERO PARK DRIVE, TRAVERSE CITY, MICHIGAN 49686, USA
TEL: (231) 946-3980 FAX: (231) 946-4772 WEB: www.youngusa.com
P/N: 03002-5-90
REV: D110210
 INTRODUCTION
MODEL 03002-5
WIND SENTRY The Wind Sentry Anemometer and Vane measure horizontal wind
INCLUDES MODELS 03102 & 03302 speed and wind direction. The small size, simplicity, and corrosion
resistant construction provide a professional quality instrument at
a modest cost. The cup wheel and vane shafts use stainless steel
precision instrument grade ball bearings which are lubricated with a
wide temperature range high quality instrument oil. Standard bearings
have light contacting seals to exclude contamination and help retain
lubricant for longer service life.

Cup wheel rotation produces an AC sine wave voltage signal with

frequency directly proportional to wind speed. This AC signal is
induced in a stationary coil by a two pole ring magnet mounted on
the cup wheel shaft. One complete sine wave cycle is produced for
each cup wheel revolution.

Wind vane position is transmitted by a 10K ohm precision conductive

plastic potentiometer which requires a regulated excitation voltage.
With a constant voltage applied to the potentiometer, the output signal
is an analog voltage directly proportional to wind direction angle.

The instrument mounts on standard 1 inch pipe, outside diameter

34mm (1.34") and is supplied with a crossarm and junction box for
cable connections. Wind Sentry anemometers and windvanes are
available separately with similar mounting and junction box.

WIND SPEED SPECIFICATION SUMMARY

INITIAL CHECK-OUT
Range 0 to 50 m/s (112 mph), gust survival 60 When the Wind Sentry is unpacked, check it carefully for any signs
m/s (134 mph) of shipping damage. Place the cup wheel on the anemometer shaft
Sensor 12 cm diameter cup wheel assembly, and secure it by tightening the set screw on the side of the hub. The
40 mm diameter hemispherical cups instrument is aligned, balanced, and fully calibrated before shipment;
however, it should be checked both mechanically and electrically
Turning Factor 75 cm (2.46 ft) before installation. The vane and cup wheel should easily rotate
Distance Constant 2.3 m (7.5 ft) (63% recovery) 360 without friction. Check vane balance by holding the instrument
Threshold 0.5 m/s (1.1 mph) so the vane surface is horizontal. It should have near-neutral torque
Transducer Stationary coil, 1300 ohm nominal resistance without any particular tendency to rotate. A slight imbalance will not
degrade performance.
Transducer Output AC sine wave signal induced by rotating
magnet on cup wheel shaft 100 mV p-p at The wind direction potentiometer requires a stable DC excitation
60 rpm. 6V p-p at 3600 rpm. voltage. Do not exceed 15 volts. When the potentiometer wiper is
Output Frequency 1 cycle per cup wheel revolution. in the 8 deadband region, the output signal is "floating" and may
show varying or unpredictable values. To prevent false readings,
signal conditioning electronics should clamp the signal to excitation
or reference level when this occurs. Note: All YOUNG signal
WIND DIRECTION (AZIMUTH) SPECIFICATION SUMMARY conditioning devices clamp the signal to excitation level. Avoid
a short circuit between the wind direction signal line and either the
excitation or ground reference lines. Although there is a current
Range 360 mechanical, 352 electrical (8 open) limiting resistor in series with the wiper for protection, damage to the
Sensor Balanced vane, 16 cm turning radius. potentiometer may occur if a short circuit condition exists.
Damping Ratio 0.2
Delay Distance (50% recovery) 0.5 m (1.6 ft) Before installation, connect the instrument to a signal conditioning
device as shown in the wiring diagram and check for proper wind
Threshold 0.8 m/s (1.8 mph) at 10 displacement speed and direction values. To check wind speed, temporarily remove
Transducer Precision conductive plastic potentiometer, the cup wheel and connect an Anemometer Drive to the cup wheel
10K ohm 20% resistance 1.0% linearity, shaft. Details appear in the CALIBRATION section.
life expectancy 50 million revolutions Rated
1 watt at 40C, 0 watts at 125C
Transducer Excitation Requirement Regulated DC voltage, 15 INSTALLATION
VDC max Proper placement of the instrument is very important. Eddies from
Transducer Output Analog DC voltage proportional to wind trees, buildings, or other structures can greatly influence wind
direction angle with regulated excitation speed and direction observations. To get meaningful data for most
voltage applied across potentiometer applications, locate the instrument well above or upwind of such
obstructions. As a general rule, the air flow around a structure is
GENERAL disturbed to twice the height of the structure upwind, six times the
height downwind, and twice the height of the structure above ground.
Operating Temperature -50 to 50C (-58 to 122F) For some observations it may not be practical or necessary to meet
these guidelines.
03002-5-90(D)

Page 1
 conditioning occurs at 352. For example, in a circuit where 0 to
FAILURE TO PROPERLY GROUND THE WIND SENTRY 1.00 VDC represents 0 to 360, the output must be adjusted for
MAY RESULT IN ERRONEOUS SIGNALS 0.978 VDC when the instrument is at 352 full scale. (352/360 X
OR TRANSDUCER DAMAGE. 1.00 volts = 0.978 volts)

Grounding the Wind Sentry is vitally important. Without proper grounding, Wind speed calibration is determined by the cup wheel turning factor
static electrical charge can build up during certain atmospheric conditions and the output characteristics of the transducer. Calibration formulas
and discharge through the transducers. This discharge can cause showing cup wheel rpm and frequency output vs. wind speed are
erroneous signals or transducer failure. To direct the discharge away included below.
from the transducers, the instrument is made with a special anti-static
plastic. It is very important that the instrument be connected to a good To calibrate wind system electronics using an actual signal from
earth ground. There are two ways this may be accomplished. First, the instrument, temporarily remove the cup wheel and connect an
the Wind Sentry may be mounted on a metal pipe which is connected Anemometer Drive to the cup wheel shaft. Calculate wind speed by
to earth ground. The mounting pipe should not be painted where the applying the appropriate calibration formula to the motor rpm and
Wind Sentry is mounted. Towers or masts set in concrete should be adjust the signal conditioning electronics for proper value. For example,
connected to one or more grounding rods. If it is difficult to ground the with the cup wheel shaft turning at 1800 rpm, adjust the indicator to
mounting post in this manner, the following method should be used. display 22.7 meters per second. ([(0.01250 X 1800) + 0.2] = 22.7)
Inside the junction box the terminal labeled EARTH GND is internally
connected to the anti-static housings. This terminal should be connected CALIBRATION FORMULAS
to an earth ground (Refer to wiring diagram).
Model 03102 Wind Sentry Anemometer
Initial installation is most easily done with two people; one to adjust
the instrument position and the other to observe the indicating device. WIND SPEED vs CUP WHEEL RPM
When anemometer and vane are mounted on the same cross arm m/s = (0.01250 x rpm) + 0.2
(Model 03002), the azimuth potentiometer has been aligned at the knots = (0.02427 x rpm) + 0.4
factory such that the mounting cross arm should be oriented North- mph = (0.02795 x rpm) + 0.4
South with the vane on the North end. km/hr = (0.04499 x rpm) + 0.7

To install the Wind Sentry, follow these steps: WIND SPEED vs OUTPUT FREQUENCY - Hz
m/s = (0.7500 x Hz) + 0.2
1. MOUNT WIND SENTRY knots = (1.4562 x Hz) + 0.4
a) Connect sensor cable to Wind Sentry junction box. mph = (1.6770 x Hz) + 0.4
b) Place Wind Sentry on mounting post. Do Not tighten km/hr = (2.6994 x Hz) + 0.7
band clamp yet.
c) Connect sensor cable to indicator.

2. ALIGN VANE MAINTENANCE

a) Select a known azimuth reference point on the horizon.
b) Sighting down vane centerline, point counterweight at Given proper care, the Wind Sentry should provide years of service.
reference point on horizon. Because of its durable, corrosion resistant construction, the instrument
c) While holding vane in position, slowly turn base until requires little maintenance. The only components likely to require
indicator displays proper value. replacement due to normal wear are the precision ball bearings and
d) Tighten mounting post band clamp. the azimuth potentiometer. Replacement of these components should
only be performed by a qualified instrument technician. If service
facilities are not available, return the instrument to the factory. Refer
to the accompanying drawings to become familiar with part names
CALIBRATION and locations. Maximum torque on all set screws is 80 oz-in.

The Wind Sentry is fully calibrated before shipment and should POTENTIOMETER REPLACEMENT
require no adjustments. Recalibration may be necessary after some
maintenance operations. Periodic calibration checks are desirable The potentiometer has a life expectancy of fifty million revolutions.
and may be necessary where the instrument is used in programs As it becomes worn, the element may produce noisy signals or
which require auditing of sensor performance. become non-linear. When the signal noise or non-linearity become
unacceptable, replace the potentiometer as follows:
For wind direction calibration, the following method can yield an
accuracy of 5 or better if carefully done. Begin by connecting 1. REMOVE POTENTIOMETER
the instrument to a signal conditioning circuit which indicates wind a) Remove three screws which secure upper and lower
direction value. This may be an indicator which displays wind direction sections of main housing.
values in angular degrees or simply a voltmeter monitoring the output.
b) Carefully remove upper housing exposing wiring connections
Hold or mount the instrument so the vane center of rotation is over
to circuit board.
the center of a sheet of paper which has 30 or 45 crossmarkings.
c) Unsolder potentiometer wires from circuit board.
Position the instrument so the mounting crossarm is oriented north-
Note color coding.
south with the vane on the north and the anemometer on the south.
With the counterweight pointing directly at the anemometer the wind d) Using a knife blade or similar instrument, loosen
direction signal should correspond to 180 or due south. Looking from potentiometer assembly from upper housing and slide it out.
above, visually align the vane with each of the crossmarkings and
observe the indicator display. It should correspond to vane position 2. INSTALL NEW POTENTIOMETER
within 5. If not, it may be necessary to adjust the relative position of a) Slide new potentiometer cell into upper housing. Be sure to
the vane skirt and shaft. See step 3 in the MAINTENANCE section engage cell key into housing notch.
under potentiometer replacement. b) Solder potentiometer wires to circuit board.
Observe color code.
It is important to note that while the sensor mechanically rotates c) Join two sections of main housing. Secure with screws
through 360, the full scale wind direction signal from the signal removed in step 1a.
03002-5-90(D)

Page 2
3. ALIGN VANE WARRANTY
a) Connect excitation voltage and signal conditioning
electronics to instrument according to wiring diagram. This product is warranted to be free of defects in materials and
b) Loosen set screw in side of vane hub. construction for a period of 12 months from date of initial purchase.
c) Position instrument so crossarm is oriented north-south Liability is limited to repair or replacement of defective item. A copy
with vane on north side. Orient vane to a known angular of the warranty policy may be obtained from R. M. Young Company.
reference. (See CALIBRATION section.)
d) While holding vane in reference position, slowly turn vane
skirt until signal conditioning system indicates proper value. CE Compliance
e) Tighten set screw on side of vane hub. Do not exceed
80 oz-in torque. This product has been tested and shown to comply with European
CE requirements for the EMC Directive. Please note that shielded
ANEMOMETER FLANGE BEARING REPLACEMENT cable must be used.

If anemometer bearings become noisy or wind speed threshold

increases above an acceptable level, replace the bearings. Check
bearing condition by hanging an ordinary paper clip (0.5 gm) on the Declaration of Conformity
outside edge of one cup while the instrument is held in a horizontal
position. The cup should rotate downward. Failure to rotate due to R. M. Young Company
the weight of the paper clip indicates anemometer bearings need 2801 Aero Park Drive
replacement. Repeat this test at different positions to check full Traverse City, MI 49686 USA
bearing rotation. Replace bearings as follows:
Models 03002, 03102, 03302
1. REMOVE BEARINGS
a) Loosen set screw on side of cup wheel hub. Remove cup The undersigned hereby declares on behalf of R. M.
wheel. Young Company that the above-referenced product, to
b) Remove three screws which hold two sections of main which this declaration relates, is in conformity with the
housing. provisions of:
c) Carefully separate upper and lower housing. Remove
coil transducer assembly from upper housing. Do not Council Directive 2004/108/EC (December 15, 2004)
disconnect from circuit board. on Electromagnetic Compatibility
d) Loosen screw and remove ring magnet on end of shaft
inside upper housing.
e) Slide shaft and skirt assembly out of both upper and lower
bearings.
f) Using knife blade under bearing flange, carefully remove David Poinsett
upper bearing. R&D Manager
g) Using a pencil, gently push out lower bearing from above.

2. INSTALL NEW BEARINGS

a) Insert new upper bearing. Use care not to apply excessive
pressure.
b) Slide cup wheel shaft through upper bearing.
c) Slide lower bearing on shaft inside upper housing.
d) Using ring magnet assembly, push lower bearing into
its seat in upper housing.
e) Secure ring magnet to shaft using screw removed in
step 1d. Use a small amount of sealant on screw to
prevent it from loosening.
f) Join two housing sections. Secure using three screws
removed in step 1b.
g) Place cup wheel on shaft. Tighten set screw on side
of hub. Do not exceed 80 oz-in torque.

VANE FLANGE BEARING REPLACEMENT

If vane bearings become noisy or if wind direction threshold increases

above an acceptable level, replace the bearings. Check bearing
condition by adding two ordinary paper clips (0.5 gm each) to the
back edge of the vane fin while the instrument and vane are held
in a horizontal position. Gently release the vane. It should rotate
downward. Failure to do so indicates the bearings need replacement.
Repeat this test at various positions to check full bearing rotation.
Since this procedure is similar to anemometer bearing replacement,
only the major steps are shown here:

1. REMOVE BEARINGS
(Remove coupling disc - same as ring magnet)
2. INSTALL NEW BEARINGS
3. ALIGN VANE (See CALIBRATION section)

03002-5-90(D)

Page 3
 CABLE & WIRING DIAGRAM

03002-5-90(D)

Page 4
GENERAL ASSEMBLY & REPLACEMENT PARTS

03002-5-90(D)

Page 5
 Campbell Scientific Companies
Campbell Scientific, Inc. (CSI)
815 West 1800 North
Logan, Utah 84321
UNITED STATES
www.campbellsci.com info@campbellsci.com

Campbell Scientific Africa Pty. Ltd. (CSAf)

PO Box 2450
Somerset West 7129
SOUTH AFRICA
www.csafrica.co.za cleroux@csafrica.co.za

Campbell Scientific Australia Pty. Ltd. (CSA)

PO Box 8108
Garbutt Post Shop QLD 4814
AUSTRALIA
www.campbellsci.com.au info@campbellsci.com.au

Campbell Scientific do Brasil Ltda. (CSB)

Rua Apinags, nbr. 2018 Perdizes
CEP: 01258-00 So Paulo SP
BRASIL
www.campbellsci.com.br vendas@campbellsci.com.br

Campbell Scientific Canada Corp. (CSC)

11564 - 149th Street NW
Edmonton, Alberta T5M 1W7
CANADA
www.campbellsci.ca dataloggers@campbellsci.ca

Campbell Scientific Centro Caribe S.A. (CSCC)

300 N Cementerio, Edificio Breller
Santo Domingo, Heredia 40305
COSTA RICA
www.campbellsci.cc info@campbellsci.cc

Campbell Scientific Ltd. (CSL)

Campbell Park
80 Hathern Road
Shepshed, Loughborough LE12 9GX
UNITED KINGDOM
www.campbellsci.co.uk sales@campbellsci.co.uk

Campbell Scientific Ltd. (CSL France)

3 Avenue de la Division Leclerc
92160 ANTONY
FRANCE
www.campbellsci.fr info@campbellsci.fr

Campbell Scientific Ltd. (CSL Germany)

Fahrenheitstrae 13
28359 Bremen
GERMANY
www.campbellsci.de info@campbellsci.de

Campbell Scientific Spain, S. L. (CSL Spain)

Avda. Pompeu Fabra 7-9, local 1
08024 Barcelona
SPAIN
www.campbellsci.es info@campbellsci.es

Please visit www.campbellsci.com to obtain contact information for your local US or international representative.