GROUP 11 SELF-DIAGNOSTIC SYSTEM

1. OUTLINE
When any abnormality occurs in the ADVANCED CAPO system caused by electric parts malfunction
and by open or short circuit, the MCU diagnoses the problem and sends the error codes to the
cluster and also stores them in the memory.

2. MONITORING
1) Active fault

21093CD66

21093CD66A 21093CD66B

The active faults of the MCU or engine ECM can be checked by this menu.

2) Logged fault

21093CD66C

21093CD66D 21093CD66E

The logged faults of the MCU or engine ECM can be checked by this menu.

3) Delete fault

21093CD66F

21093CD66G 21093CD66H

The logged faults of the MCU or engine ECM can be deleted by this menu.

5-14
3. MACHINE ERROR CODES TABLE
Error code
Description
HCESPN FMI
3 Hydraulic oil temperature sensor circuit - Voltage above normal, or shorted to high source.
101
4 Hydraulic oil temperature circuit - Voltage below normal, or shorted to low source.
0 Working pressure sensor data above normal range.
1 Working pressure sensor data below normal range.
105
2 Working pressure sensor data error.
4 Working pressure sensor circuit - Voltage below normal, or shorted to Low source.
0 Travel oil pressure sensor data above normal range.
1 Travel oil pressure sensor data below normal range.
108
2 Travel oil pressure sensor data error.
4 Travel oil pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Main pump 1 (P1) pressure sensor data above normal range.
1 Main pump 1 (P1) pressure sensor data below normal range.
120 2 Main pump 1 (P1) pressure sensor data error.
Main pump 1 (P1) pressure sensor circuit - Voltage below normal, or shorted to low
4
source.
0 Main pump 2 (P2) pressure sensor data above normal range.
1 Main pump 2 (P2) pressure sensor data below normal range.
121 2 Main pump 2 (P2) pressure sensor data error.
Main pump 2 (P2) pressure sensor circuit - Voltage below normal, or shorted to low
4
source.
0 Overhead pressure sensor data above normal range.
1 Overhead pressure sensor data below normal range.
122
2 Overhead pressure sensor data error.
4 Overhead pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Negative 1 pressure sensor data above normal range.
1 Negative 1 pressure sensor data below normal range.
123
2 Negative 1 pressure sensor data error.
4 Negative 1 pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Negative 2 Pressure sensor data above normal range.
1 Negative 2 Pressure sensor data below normal range.
124
2 Negative 2 Pressure sensor data error.
4 Negative 2 Pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Pilot pump (P3) pressure sensor data above normal range.
1 Pilot pump (P3) pressure sensor data below normal range.
125
2 Pilot pump (P3) pressure sensor data error.
4 Pilot pump (P3) pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Boom up pilot pressure sensor data above normal range.
1 Boom up pilot pressure sensor data below normal range.
127
2 Boom up pilot pressure sensor data error.
4 Boom up pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Arm in/out & bucket in pilot pressure sensor data above normal range.
1 Arm in/out & bucket in pilot pressure sensor data below normal range.
133 2 Arm in/out & bucket in pilot pressure sensor data error.
Arm in/out & bucket in pilot pressure sensor circuit - Voltage below normal, or shorted to
4
low source.
Some error codes are not applied to this machine.

5-15
 Error code
Description
HCESPN FMI
0 Swing pilot pressure sensor data above normal range.
1 Swing pilot pressure sensor data below normal range.
135
2 Swing pilot pressure sensor data error.
4 Swing pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Attachment pilot pressure sensor data above normal range.
1 Attachment pilot pressure sensor data below normal range.
138
2 Attachment pilot pressure sensor data error.
4 Attachment pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
5 Pump EPPR valve circuit - Current below normal, or open circuit.
140
6 Pump EPPR valve circuit - Current above normal.
5 Boom priority EPPR valve circuit - Current below normal, or open circuit.
141
6 Boom priority EPPR valve circuit - Current above normal.
5 Travel EPPR valve circuit - Current below normal, or open circuit.
143
6 Travel EPPR valve circuit - Current above normal.
5 Attachment flow EPPR valve circuit - Current below normal, or open circuit.
144
6 Attachment flow EPPR valve circuit - Current above normal.
5 Remote cooling fan EPPR valve circuit - Current below normal, or open circuit.
145
6 Remote cooling fan EPPR valve circuit - Current above normal.
5 Left rotate EPPR valve circuit - Current below normal, or open circuit.
150
6 Left rotate EPPR valve circuit - Current above normal.
5 Right rotate EPPR valve circuit - Current below normal, or open circuit.
151
6 Right rotate EPPR valve circuit - Current above normal.
5 Left tilt EPPR valve circuit - Current below normal, or open circuit.
152
6 Left tilt EPPR valve circuit - Current above normal.
5 Right tilt EPPR valve circuit - Current below normal, or open circuit.
153
6 Right tilt EPPR valve circuit - Current above normal.
5 Power max solenoid circuit - Current below normal, or open circuit.
166
6 Power max solenoid circuit - Current above normal.
5 Travel speed solenoid circuit - Current below normal, or open circuit.
167
6 Travel speed solenoid circuit - Current above normal.
5 Attachment pressure solenoid circuit - Current below normal, or open circuit.
168
6 Attachment pressure solenoid circuit - Current above normal.
5 Attachment conflux solenoid circuit - Current below normal, or open circuit.
169
6 Attachment conflux solenoid circuit - Current above normal.
5 Arm regeneration solenoid circuit - Current below normal, or open circuit.
170
6 Arm regeneration solenoid circuit - Current above normal.
5 Attachment safety solenoid circuit - Current below normal, or open circuit.
171
6 Attachment safety solenoid circuit - Current above normal.
5 Remote cooling fan reverse solenoid circuit - Current below normal, or open circuit.
181
6 Remote cooling fan reverse solenoid circuit - Current above normal.
5 Fuel level sensor circuit - Voltage above normal, or shorted to high source.
301
6 Fuel level sensor circuit - Voltage below normal, or shorted to low source.
Engine coolant temperature sensor circuit - Voltage above normal, or shorted to high
3
source.
304
Engine coolant temperature sensor circuit - Voltage below normal, or shorted to low
4
source.
310 8 Engine speed signal error - Abnormal frequency or pulse width.
3 Engine preheat relay circuit - Voltage above normal, or shorted to high source.
322
4 Engine preheat relay circuit - Voltage below normal, or shorted to low source.
3 Fuel warmer relay circuit - Voltage above normal, or shorted to high source.
325
4 Fuel warmer relay circuit - Voltage below normal, or shorted to low source.
Some error codes are not applied to this machine.

5-16
 Error code
Description
HCESPN FMI
3 Potentiometer (G/A) circuit - Voltage above normal, or shorted to high source.
340
4 Potentiometer (G/A) circuit - Voltage below normal, or shorted to low source.
5 Governor actuator circuit - Current below normal, or open circuit.
341
6 Governor actuator circuit - Current above normal.
0 Transmission oil pressure sensor data above normal range.
1 Transmission oil pressure sensor data below normal range.
501
2 Transmission oil pressure sensor data error.
4 Transmission oil pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Brake pressure sensor data above normal range.
1 Brake pressure sensor data below normal range.
503
2 Brake pressure sensor data error.
4 Brake pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Working brake pressure sensor data above normal range.
1 Working brake pressure sensor data below normal range.
505
2 Working brake pressure sensor data error.
4 Working brake pressure sensor circuit - Voltage below normal, or shorted to low source.
3 Working brake lamp circuit - Voltage above normal, or shorted to high source.
506
4 Working brake lamp circuit - Voltage below normal, or shorted to low source.
3 Ram lock lamp circuit - Voltage above normal, or shorted to high source.
520
4 Ram lock lamp circuit - Voltage below normal, or shorted to low source.
5 Ram lock solenoid circuit - Current below normal, or open circuit.
525
6 Ram lock solenoid circuit - Current above normal.
0 Travel F pilot pressure sensor data above normal range.
1 Travel F pilot pressure sensor data below normal range.
530
2 Travel F pilot pressure sensor data error.
4 Travel F pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Travel R pilot pressure sensor data above normal range.
1 Travel R pilot pressure sensor data below normal range.
531
2 Travel R pilot pressure sensor data error.
4 Travel R pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
3 Hourmeter circuit - Voltage above normal, or shorted to high source.
701
4 Hourmeter circuit - Voltage below normal, or shorted to low source.
0 MCU input voltage high.
705
1 MCU input voltage low.
707 1 Alternator node I voltage low.
3 Acc. dial circuit - Voltage above normal, or shorted to high source.
714
4 Acc. dial circuit - Voltage below normal, or shorted to low source.
3 Rotate signal input circuit - Voltage above normal, or shorted to high source.
715
4 Rotate signal input circuit - Voltage below normal, or shorted to low source.
3 Tilt signal input circuit - Voltage above normal, or shorted to high source.
716
4 Tilt signal input circuit - Voltage below normal, or shorted to low source.
3 Travel alarm (buzzer) circuit - Voltage above normal, or shorted to high source.
722
4 Travel alarm (buzzer) circuit - Voltage below normal, or shorted to low source.
830 12 MCU internal memory error.
840 2 Cluster communication data error.
841 2 ECM communication data error.
843 2 Option #1 (CAN 2) communication data error.
850 2 RCM communication data error.
Some error codes are not applied to this machine.

5-17
4. ENGINE FAULT CODE
Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
Engine control module critical internal failure - Possible no noticeable performance effects,
111
Bad intelligent device or component. Error engine dying, or hard starting.
629
internal to the ECM related to memory hardware
12
failures or internal ECM voltage supply circuits.
Engine magnetic crankshaft speed/position lost Fueling to injectors is disabled and the engine
115 both of two signals - Data erratic, intermittent, or can not be started.
612 incorrect. The ECM has detected that the primary
2 engine speed sensor and the backup engine
speed sensor signals are reversed.
Intake manifold 1 pressure sensor circuit - Engine power derate.
122
Voltage above normal, or shorted to high source.
102
High signal voltage detected at the intake
3
manifold pressure circuit.
Intake manifold 1 pressure sensor circuit - Engine power derate.
123
Voltage below normal, or shorted to low Source.
102
Low signal voltage or open circuit detected at the
4
intake manifold pressure circuit.
Intake manifold 1 pressure - Data valid but above Engine power derate.
124
normal operational range - Moderately severe
102
level. Intake manifold pressure has exceeded the
16
maximum limit for the given engine rating.
Accelerator pedal or lever position sensor 1 Severe derate in power output of the engine.
131
circuit - Voltage above normal, or shorted to high Limp home power only.
91
source. High voltage detected at accelerator
3
pedal position circuit.
Accelerator pedal or lever position sensor 1 Severe derate in power output of the engine.
132
circuit - Voltage below normal, or shorted to low Limp home power only.
91
source. Low voltage detected at accelerator
4
pedal position signal circuit.
Remote accelerator pedal or lever position Remote accelerator will not operate. Remote
133
sensor 1 circuit - Voltage above normal, or accelerator position will be set to zero percent.
974
shorted to high source. High voltage detected at
3
remote accelerator pedal position circuit.
Remote accelerator pedal or lever position Remote accelerator will not operate. Remote
134
sensor 1 circuit - Voltage below normal, or accelerator position will be set to zero percent.
974
shorted to low source. Low voltage detected at
4
remote accelerator pedal position signal circuit.
Engine oil rifle pressure 1 sensor circuit - Voltage None on performance. No engine protection for
135
above normal, or shorted to high source. High oil pressure.
100
signal voltage detected at the engine oil pressure
3
circuit.
Engine oil rifle pressure 1 sensor circuit - Voltage None on performance. No engine protection for
141
below normal, or shorted to low source. Low oil pressure.
100
signal voltage detected at engine oil pressure
4
circuit.
143 Engine oil rifle pressure - Data valid but below None on performance.
100 normal operational range - Moderately severe
18 level.
Engine coolant temperature 1 sensor circuit - Possible white smoke. Fan will stay ON if
144
Voltage above normal, or shorted to high source. controlled by ECM. No engine protection for
110
High signal voltage or open circuit detected at engine coolant temperature.
3
engine coolant temperature circuit.
Some fault codes are not applied to this machine.

5-18
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
Engine Coolant Temperature 1 Sensor Circuit - Possible white smoke. Fan will stay ON if
145 Voltage Below Normal, or Shorted to Low controlled by ECM. No engine protection for
110
Source. Low signal voltage detected at engine engine coolant temperature.
4
coolant temperature circuit.
Engine Coolant Temperature - Data Valid but Progressive power derate increasing in severity
146 Above Normal Operational Range - Moderately from time of alert.
110 Severe Level. Engine coolant temperature signal
16 indicates engine coolant temperature is above
engine protection warning limit.
Accelerator Pedal or Lever Position 1 Sensor Severe derate in power output of the engine.
147 Circuit Frequency - Data Valid but Below Normal Limp home power only.
91 Operational Range - Most Severe Level. A
1 frequency of less than 100 Hz has been detected
at the frequency throttle input to the ECM.
Accelerator Pedal or Lever Position Sensor 1 - Severe derate in power output of the engine.
148 Data Valid but Above Normal Operational Range Limp home power only.
91 - Most Severe Level. A frequency of more than
0 1500 Hz has been detected at the frequency
throttle input to the ECM.
Engine Coolant Temperature - Data Valid but Progressive power derate increasing in severity
151 Above Normal Operational Range - Most Severe from time of aler t. If Engine Protection
110 Level. Engine coolant temperature signal Shutdown feature is enabled, engine will shut
0 indicates engine coolant temperature above down 30 seconds after Red Stop Lamp starts
engine protection critical limit. flashing.
Intake Manifold 1 Temperature Sensor Circuit - Possible white smoke. Fan will stay ON if
153
Voltage Above Normal, or Shorted to High controlled by ECM. No engine protection for
105
3 Source. High signal voltage detected at intake intake manifold air temperature.
manifold air temperature circuit.
Intake Manifold 1 Temperature Sensor Circuit - Possible white smoke. Fan will stay ON if
154
Voltage Below Normal, or Shorted to Low controlled by ECM. No engine protection for
105
4 Source. Low signal voltage detected at intake intake manifold air temperature.
manifold air temperature circuit.
Intake Manifold 1 Temperature - Data Valid but Progressive power derate increasing in severity
155 Above Normal Operational Range - Most Severe from time of aler t. If Engine Protection
105 Level. Intake manifold air temperature signal Shutdown feature is enabled, engine will shut
0 indicates intake manifold air temperature above down 30 seconds after Red Stop Lamp starts
engine protection critical limit. flashing.
187 Sensor Supply 2 Circuit - Voltage Below Normal, Engine power derate.
520195 or Shorted to Low Source. Low voltage detected
4 at the sensor supply number 2 circuit.
195 Coolant Level Sensor 1 Circuit - Voltage Above None on performance.
111 Normal, or Shorted to High Source. High signal
3 voltage detected at engine coolant level circuit.
196 Coolant Level Sensor 1 Circuit - Voltage Below None on performance.
111 Normal, or Shorted to Low Source. Low signal
4 voltage detected at engine coolant level circuit.
197 Coolant Level - Data Valid but Below Normal None on performance.
111 Operational Range - Moderately Severe Level.
18 Low coolant level has been detected.
Barometric Pressure Sensor Circuit - Voltage Engine power derate.
221 Above Normal, or Shorted to High Source. High
108
signal voltage detected at barometric pressure
3
circuit.
Some fault codes are not applied to this machine.

5-19
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
Barometric Pressure Sensor Circuit - Voltage Engine power derate.
222
Below Normal, or Shorted to Low Source. Low
108
signal voltage detected at barometric pressure
4
circuit.
227 Sensor Supply 2 Circuit - Voltage Above Normal, Engine power derate.
520195 or Shorted to High Source. High voltage detected
3 at sensor supply number 2 circuit.
Engine Crankshaft Speed/Position - Data Valid Fuel injection disabled until engine speed falls
234
but Above Normal Operational Range - Most below the overspeed limit.
190
Severe Level. Engine speed signal indicates
0
engine speed above engine protection limit.
Coolant Level - Data Valid but Below Normal Progressive power derate increasing in severity
235 Operational Range - Most Severe Level. Low from time of aler t. If Engine Protection
111 engine coolant level detected. Shutdown feature is enabled, engine will shut
1 down 30 seconds after Red Stop Lamp starts
flashing.
External Speed Command Input (Multiple Unit
237
Synchronization) - Data Erratic, Intermittent, or
644
Incorrect. Communication between multiple
2
engines may be intermittent.
Sensor Supply 3 Circuit - Voltage Below Normal, Possible hard starting and rough running.
238
or Shorted to Low Source. Low voltage detected
520196
on the +5 volt sensor supply circuit to the engine
4
speed sensor.
Wheel-based vehicle speed - Data erratic, Engine speed limited to ,maximum engine
241
intermittent, or incorrect. The ECM lost the speed without VSS parameter value. Cruise
84
vehicle speed signal. control, gear-down protection, and road speed
2
governor will not work.
Wheel-based vehicle speed sensor circuit Engine speed limited to maximum engine
242
tampering has been detected - Abnormal rate of speed without VSS parameter value. Cruise
84
change. Signal indicates an intermittent control, gear-down protection, and road speed
10
connection or VSS tampering. g+H53overnor will not work.
Fan control circuit - Voltage below normal, or The fan may stay on continuously or not run at
245
shorted to low source. Low signal voltage all.
647
detected at the fan control circuit when
4
commanded on.
268 Injector metering rail 1 pressure - data erratic, The ECM will estimate fuel pressure, and power
94 intermittent, or incorrect. The ECM has detected is reduced.
2 that the fuel pressure signal is not changing.
Fuel pump pressurizing assembly 1 circuit - Engine will run poorly at idle. Engine will have
271
Voltage below normal, or shorted to low source. low power. Fuel pressure will be higher than
1347
Low signal voltage detected at the fuel pump commanded.
4
actuator circuit.
Fuel pump pressurizing assembly 1 circuit - Engine will not run or engine will run poorly.
272
Voltage above normal, or shorted to high source.
1347
High signal voltage or open circuit detected at the
3
fuel pump actuator circuit.
275 Fuel pumping element number 1 (front) - Engine will not run or possible low power.
1347 Mechanical system not responding properly or
7 out of adjustment.
281 Fuel pump pressurizing assembly 1 - Mechanical Engine will not run or possible low power.
1347 system not responding properly or out of
7 adjustment.
SAE J1939 multiplexing PGN timeout error - At least one multiplexed device will not operate
285
Abnormal update rate. The ECM expected properly.
639
information from a multiplexed device but did not
9
receive it soon enough or did not receive it at all.
Some fault codes are not applied to this machine.

5-20
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
SAE J1939 multiplexing configuration error - At least one multiplexed device will not operate
286
Out of calibration. The ECM expected properly.
639
information from a multiplexed device but only
13
received a portion of the necessary information.
SAE J1939 multiplexed accelerator pedal or lever Engine may only idle or engine will not
287
sensor system - received network data In error. accelerate to full speed.
91
The OEM vehicle electronic control unit (VECM)
19
detected a fault with its accelerator pedal.
SAE J1939 Multiplexing Remote Accelerator The engine will not respond to the remote
288 Pedal or Lever Position Sensor Circuit - Received throttle. Engine may only idle. The primary or
974 Network Data In Error. The OEM vehicle cab accelerator may be able to be used.
19 electronic control unit (VECU) detected a fault
with the remote accelerator.
292 Auxiliary temperature Sensor Input 1 - Special Possible engine power derate.
441 instructions.
14
Auxiliary temperature sensor input 1 circuit - None on performance.
293
Voltage above normal, or shorted to high source.
441
High signal voltage or open circuit detected at
3
the OEM auxiliary temperature circuit.
Auxiliary temperature sensor input 1 circuit - None on performance.
294
Voltage below normal, or shorted to low source.
441
Low signal voltage detected at the OEM auxiliary
4
temperature circuit.
296 Auxiliary pressure sensor input 1 - Special Possible engine power derate.
1388 instructions.
14
Auxiliary pressure sensor input 1 circuit - Voltage None on performance.
297
above normal, or shorted to high source. High
1388
signal voltage detected at the OEM pressure
3
circuit.
Auxiliary pressure sensor input 1 circuit - Voltage None on performance.
298
below normal, or shorted to low source. Low
1388
signal voltage or open circuit detected at the
4
OEM pressure circuit.
319 Real time clock power interrupt - Data erratic, None on performance. Data in the ECM will not
251 intermittent, or incorrect. Real time clock lost have accurate time and date information.
2 power.
Injector solenoid driver cylinder 1 circuit - Current Engine can possibly misfire or run rough.
below normal, or open circuit. High resistance
322
detected on injector number 1 circuit or no
651
current detected at number 1 injector driver or
5
return pin when the voltage supply at the
harness is on.
Injector solenoid driver cylinder 5 circuit - Current Engine can possibly misfire or run rough.
below normal, or open circuit. High resistance
323
detected on injector number 5 circuit or no
655
current detected at number 5 injector driver or
5
return pin when the voltage supply at the
harness is on.
Injector solenoid driver cylinder 3 circuit - Current Engine can possibly misfire or run rough.
below normal, or open circuit. High resistance
324
detected on injector number 3 circuit or no
653
current detected at number 3 injector driver or
5
return pin when the voltage supply at the
harness is on.
Some fault codes are not applied to this machine.

5-21
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
Injector solenoid driver cylinder 6 circuit - Current Engine can possibly misfire or run rough.
below normal, or open circuit. High resistance
325
detected on injector number 6 circuit or no
656
current detected at number 6 injector driver or
5
return pin when the voltage supply at the
harness is on.
Injector solenoid driver cylinder 2 circuit - Current Engine can possibly misfire or run rough.
below normal, or open circuit. High resistance
331
detected on injector number 2 circuit or no
652
current detected at number 2 injector driver or
5
return pin when the voltage supply at the
harness is on.
Injector solenoid driver cylinder 4 circuit - Current Engine can possibly misfire or run rough.
below normal, or open circuit. High resistance
332
detected on injector number 4 circuit or no
654
current detected at number 4 injector driver or
5
return pin when the voltage supply at the
harness is on.
Engine coolant temperature - Data erratic, The ECM will estimate engine coolant
334
intermittent, or incorrect. The engine coolant temperature.
110
temperature reading is not changing with engine
2
operating conditions.
342 Electronic calibration code incompatibility - Out of Possible no noticeable performance effects,
630 calibration. An incompatible calibration has been engine dying, or hard starting.
13 detected in the ECM.
343 Engine control module warning internal hardware No performance effects or possible severe
629 failure - Bad intelligent device or component. power derate.
12 Internal ECM failure.
351 Injector power supply - Bad intelligent device or Possible smoke, low power, engine misfire,
627 component. The ECM measured injector boost and/or engine will not start.
12 voltage is low.
352 Sensor supply 1 circuit - Voltage below normal, Engine power derate.
1079 or shorted to low source. Low voltage detected at
4 sensor supply number 1 circuit.
386 Sensor supply 1 circuit - Voltage above normal, Engine power derate.
1079 or shorted to high source. High voltage detected
3 at sensor supply number 1 circuit.
Engine oil rifle pressure - Data valid but below
Progressive power derate increasing in severity
415 normal operational range - Most severe level. Oil
from time of aler t. If engine protection
100 pressure signal indicates oil pressure below the
shutdown feature is enabled, engine will shut
1 engine protection critical limit. down 30 seconds after red stop lamp starts
flashing.
418 Water in fuel indicator - Data valid but above Possible white smoke, loss of power, or hard
97 normal operational range - Least severe level. starting.
15 water has been detected in the fuel filter.
428 Water in fuel indicator sensor circuit - Voltage None on performance. No water in fuel warning
97 above normal, or shorted to high source. High available.
3 voltage detected at the water in fuel circuit.
429 Water in fuel indicator sensor circuit - Voltage None on performance. No water in fuel warning
97 below normal, or shorted to low source. Low available.
4 voltage detected at the water in fuel circuit.
Accelerator pedal or lever idle validation switch - Engine will only idle.
431
Data erratic, intermittent, or incorrect. Voltage
558
detected simultaneously on both idle validation
2
and off-idle validation switches.
Some fault codes are not applied to this machine.

5-22
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
Accelerator pedal or lever idle validation circuit - Engine will only idle.
432 Out of calibration. Voltage at idle validation
558
on-idle and off-idle circuit does not match
13
accelerator pedal position.
435 Engine oil rifle pressure - Data erratic, None on performance. No engine protection for
100 intermittent, or incorrect. An error in the engine oil oil pressure.
2 pressure switch signal was detected by the ECM.
Battery 1 voltage - Data valid but below normal Engine may stop running or be difficult to start.
441 operational range - Moderately severe level.
168
ECM supply voltage is below the minimum
18
system voltage level.
Battery 1 Voltage - Data valid but above normal Possible electrical damage to all electrical
442 operational range - Moderately severe level. components.
168
ECM supply voltage is above the maximum
16
system voltage level.
449 Injector metering rail 1 pressure - Data valid but None or possible engine noise associated with
157 above normal operational range - Most severe higher injection pressures (especially at idle or
0 level. light load). Engine power is reduced.
Injector metering rail 1 pressure sensor circuit - Power and or speed derate.
451 Voltage above normal, or shorted to high source.
157
High signal voltage detected at the rail fuel
3
pressure sensor circuit.
Injector metering rail 1 pressure sensor circuit - Power and or speed derate.
452
Voltage below normal, or shorted to low source.
157
Low signal voltage detected at the rail fuel
4
pressure sensor circuit.
Intake manifold 1 temperature - Data valid but Progressive power derate increasing in severity
488 above normal operational range - Moderately from time of alert.
105 severe level. Intake manifold air temperature
16 signal indicates intake manifold air temperature
is above the engine protection warning limit.
497 Multiple unit synchronization switch - Data None on performance.
1377 erratic, intermittent, or incorrect.
2
523 Auxiliary intermediate (PTO) speed switch None on performance.
611 validation - Data erratic, intermittent, or
2 incorrect.
Auxiliary input/output 2 circuit - Voltage above None on performance.
527
normal, or shorted to high source. High signal
702
voltage or open circuit has been detected at the
3
auxiliary input/output 2 circuit.
528 Auxiliary alternate torque validation switch - None on performance.
93 Data erratic, intermittent, or incorrect.
2
Auxiliary input/output 3 circuit - Voltage above Engine will only idle.
529 normal, or shorted to high source. Low signal
703
voltage has been detected at the auxiliary input/
3
output 2 circuit.
Injector metering rail 1 pressure - Data valid but Possibly hard to start, low power, or engine
553 above normal operational range - Moderately smoke.
157
severe level. The ECM has detected that fuel
16
pressure is higher than commanded pressure.
Some fault codes are not applied to this machine.

5-23
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
554 Injector metering rail 1 pressure - Data erratic, Either the engine will not start or the engine will
157 Intermittent, or incorrect. The ECM has detected not have starter lockout protection.
2 that the fuel pressure signal is not changing.
Injector metering rail 1 pressure - Data Valid but The engine will not have starter lockout
559 Below Normal Operational Range - Moderately protection.
157
Severe Level. The ECM has detected that fuel
18
pressure is lower than commanded pressure.
Starter relay driver circuit - Voltage above Engine power derate. The ECM uses an
584 normal, or shorted to high source. Open circuit estimated turbocharger speed.
677
or high voltage detected at starter lockout
3
circuit.
585 Starter relay driver circuit - Voltage below Amber lamp will light until high battery voltage
677 normal, or shorted to low source. Low voltage condition is corrected.
4 detected at starter lockout circuit.
Turbocharger 1 speed - Data valid but above Amber lamp will light until high battery voltage
595 normal operational range - Moderately severe condition is corrected.
103
level. High turbocharger speed has been
16
detected.
599 Auxiliary commanded dual output shutdown - None or possible engine noise associated with
640 Special instructions. higher injection pressures (especially at idle or
14 light load). Engine power is reduced.
Turbocharger 1 speed - Data valid but below Engine power derate.
687 normal operational range - Moderately severe
103
level. Low turbocharger speed detected by the
18
ECM.
689 Engine crankshaft speed/position - Data erratic, Engine power derate.
190 intermittent, or incorrect. Loss of signal from
2 crankshaft sensor.
Turbocharger 1 compressor inlet temperature Engine will run derated. Excessive black
691 circuit - Voltage above normal, or shorted to smoke, hard start, and rough idle possible.
1172 high source. High signal voltage detected at
3 turbocharger compressor inlet air temperature
circuit.
Turbocharger 1 compressor inlet temperature Possible no noticeable performance effects,
692
circuit - Voltage below normal, or shorted to low engine dying, or hard starting.
1172
4 source. Low signal voltage detected at
turbocharger compressor inlet air tempera
Engine speed / position camshaft and Possible poor starting. Engine power derate.
731 crankshaft misalignment - Mechanical system
723 not responding properly or out of adjustment.
7 mechanical misalignment between the
crankshaft and camshaft engine speed sensors.
757 Electronic control module data lost - Condition Possible poor starting. Engine power derate.
611 exists. Severe loss of data from the ECM.
31
Engine camshaft speed / position sensor - Data Possible no noticeable performance effects or
778
erratic, intermittent, or incorrect. The ECM has engine dying or hard starting. Fault information,
723
detected an error in the camshaft position trip information, and maintenance monitor data
2
sensor signal. may be inaccurate.
779 Auxiliary equipment sensor input 3 - Root Engine will shut down.
703 cause not known.
11
Some fault codes are not applied to this machine.

5-24
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
Power supply lost with ignition on - Data erratic, Engine will shut down.
intermittent, or incorrect. Supply voltage to the
1117 ECM fell below 6.2 volts momentarily, or the
627
ECM was not allowed to power down correctly
2
(retain battery voltage for 30 seconds after key
OFF).
OEM datalink cannot transmit - Data erratic, Engine will only idle.
1633 intermittent, or incorrect. Communications within
625
the OEM datalink network is intermittent.
2
Sensor supply 4 circuit - Voltage above normal, Possibly hard to start, low power, or engine
2185 or shorted to high source. High voltage detected smoke.
520197
at +5 volt sensor supply circuit to the accelerator
3
pedal position sensor.
Sensor supply 4 circuit - Voltage below normal, None or possible engine noise associated with
2186 or shorted to low source. Low voltage detected higher injection pressure (especially at idle or
520197
at +5 volt sensor supply circuit to the accelerator light load)
4
pedal position sensor.
Injector metering rail 1 pressure - Data valid but Engine may be difficult to start.
2249
below normal operational range - Most severe
157
level. The ECM has detected that fuel pressure
1
is lower than commanded pressure.
Electric lift pump for engine fuel supply circuit - Possible low power.
2265
Voltage above normal, or shorted to high
1075
source. High voltage or open detected at the
3
fuel lift pump signal circuit.
Electric lift pump for engine fuel supply circuit - Engine may exhibit misfire as control switches
2266
Voltage below normal, or shorted to low source. from the primary to the backup speed sensor.
1075
4 Low signal voltage detected at the fuel lift pump Engine power is reduced while the engine
circuit. operates on the backup speed sensor.
2311 Electronic fuel injection control valve circuit - Possible low power.
633 Condition exists. Fuel pump actuator circuit
31 resistance too high or too low.
2321 Engine crankshaft speed/position - Data erratic, Engine power derate.
190 intermittent, or incorrect. crankshaft engine
2 speed sensor intermittent synchronization.
Engine camshaft speed / position sensor - Data Engine power derate.
2322
erratic, intermittent, or incorrect. Camshaft
723
2 engine speed sensor intermittent
synchronization.
2345 Turbocharger 1 Speed - Abnormal rate of Engine power derate.
103 change. The turbocharger speed sensor has
10 detected an erroneous speed value.
Turbocharger turbine inlet temperature Engine brake on cylinders 1, 2, and 3 can not
2346 (Calculated) - Data valid but above normal be activated or exhaust brake will not operate.
2789 operational range - Least severe level.
15 Turbocharger turbine inlet temperature has
exceeded the engine protection limit.
2347 Turbocharger compressor outlet temperature Engine brake on cylinders 4, 5 and 6 can not
2790 (Calculated) - Data valid but above normal be activated or exhaust brake will not operate.
15 operational range - Least severe level.
2377 Fan control circuit - Voltage above normal, or Variable geometry turbocharger will go to the
647 shorted to high source. Open circuit or high open position.
3 voltage detected at the fan control circuit.
Some fault codes are not applied to this machine.

5-25
 Fault code
J1939 SPN Reason Effect (only when fault code is active)
J1939 FMI
2384 VGT actuator driver circuit - Voltage below The intake air heaters may be ON or OFF all
641 normal, or shorted to low source. Low voltage the time.
4 detected at turbocharger control valve circuit.
VGT actuator driver circuit - Voltage above The intake air heaters may be ON or OFF all
2385 normal, or shorted to high source. Open circuit the time.
641
or high voltage detected at turbocharger control
3
valve circuit.
2555 Intake air heater 1 circuit - Voltage above Can not control transmission.
729 normal, or shorted to high source. High voltage
3 detected at the intake air heater signal circuit.
2556 Intake air heater 1 circuit - Voltage below Can not control transmission.
729 normal, or shorted to low source. Low voltage
4 detected at the intake air heater signal circuit.
2557 Auxiliary PWM driver 1 circuit - Voltage above Power derate and possible engine shutdown if
697 normal, or shorted to high source. High signal engine protection shutdown feature is enabled.
3 voltage detected at the analog torque circuit.
2558 Auxiliary PWM driver 1 circuit - Voltage below Pregressive power derate increasing in severity
697 normal, or shorted to low source. Low signal from time of alert.
4 voltage detected at the analog torque circuit.
Intake manifold 1 pressure - Data erratic,
2973 intermittent, or incorrect. The ECM has detected
102 an intake manifold pressure signal that is too
2 high or low for current engine operating
conditions.
Some fault codes are not applied to this machine.

5-26