Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
103 views

PIR Sensor Module

This document provides information about a PIR motion detection sensor module. It uses a pyroelectric sensor to detect motion by measuring changes in infrared levels emitted by objects. It has a single digital output, small size, and can detect motion up to 6 meters away. It requires a warm-up time of 10-60 seconds to calibrate before detecting motion. The sensor module can be used in applications such as alarm systems, Halloween props, and other devices requiring motion detection.

Uploaded by

Chaitanya Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
103 views

PIR Sensor Module

This document provides information about a PIR motion detection sensor module. It uses a pyroelectric sensor to detect motion by measuring changes in infrared levels emitted by objects. It has a single digital output, small size, and can detect motion up to 6 meters away. It requires a warm-up time of 10-60 seconds to calibrate before detecting motion. The sensor module can be used in applications such as alarm systems, Halloween props, and other devices requiring motion detection.

Uploaded by

Chaitanya Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

PIR Motion Detection

Sensor Module [RKI-1370]

Users Manual

Page 1

PIR Motion Detection Sensor Module [RKI-1370]


Introduction
This Passive Infrared Sensor (PIR) module is used for motion detection. It can be uses as motion detector
on your robot. It can work from 5V to 9V DC and gives digital output. It requires 10-60 seconds of settling time
before starting its operation. It consists of pyroelectric sensor that detects motion by measuring change in the
infrared levels emitted by the objects. It can detect motion up to 6 meters.

Specifications
Single bit output
Small size makes it easy to conceal
Sensitivity: Presettable
Size: Length 32mm, Width 24mm, Thickness 26mm

Application Ideas
Alarm Systems
Halloween Props
Motion Detection Sensor

Quick Start Circuit


Note: The sensor is active high when the jumper (shown in the upper left) is in either position.

Page 2

PIR Motion Detection Sensor Module [RKI-1370]


Theory of Operation
Pyroelectric devices, such as the PIR sensor, have elements made of a crystalline material that generates
an electric charge when exposed to infrared radiation. The changes in the amount of infrared striking the element
change the voltages generated, which are measured by an on-board amplifier. The device contains a special filter
called a Fresnel lens, which focuses the infrared signals onto the element. As the ambient infrared signals
change rapidly, the on-board amplifier trips the output to indicate motion.

Pin Definitions and Ratings


GND Connects to Ground or Vss
V+ Connects to Vdd (5V to 9VDC)
OUT Output Connects to an I/O pin set to INPUT mode (or transistor/MOSFET)

Jumper Setting
H: Retrigger Mode.
Output remains HIGH when sensor is retriggered repeatedly. Output is LOW when idle (not triggered).

L: Normal Mode.
Output goes HIGH then LOW when triggered. Continuous motion results in repeated HIGH/LOW pulses.
Output is LOW when idle. PIR Motion Detection Sensor

Calibration
The PIR Sensor requires a warm-up time in order to function properly. This is due to the settling time
involved in learning its environment. This could be anywhere from 10-60 seconds. During this time there should
be as little motion as possible in the sensors field of view.

Sensitivity
The PIR Sensor has a range of approximately 20 feet. This can vary with environmental conditions. The
sensor is designed to adjust to slowly changing conditions that would happen normally as the day progresses
and the environmental conditions change, but responds by making its output high when sudden changes occur,
such as when there is motion.

Page 3

PIR Motion Detection Sensor Module [RKI-1370]

You might also like