1956 PROCEEDINGS OF THE IRE 1703

A Third Method of Generation and Detection

of Single-Sideband Signals*
DONALD K. WEAVER, JR.t, ASSOCIATE MEMBER, IRE

Summary-This paper presents a third method of generation and the input signal frequency band will result in two equal
detection of a single-sideband signal. The method is basically dif- amplitude sinusoidal signals whose phases differ by
ferent from either the conventional filter or phasing method in that900. These quadrature signals are applied to a pair of
no sharp cutoff filters or wide-band 900 phase-difference networks
are needed. This system is especially suited to keeping the signal balanced modulators. The translating carrier frequency
energy confined to the desired bandwidth. Any unwanted sideband is also divided into two 900 components. When the out-
occupies the same band as the desired sideband, and the unwanted put signals from these two balanced modulators are
sideband in the usual sense is not present. added, one set of sidebands will add in phase, generating
the desired signal, while the other sideband will cancel
Tll XHE PURPOSE of this paper is to present a third itself out. By subtracting instead of adding, it is possible
basic method of generation and detection of to change sidebands.
single-sideband signals. Two methods are com-
monly used today. A block diagram of the first of these,
the filter method, is shown in Fig. 1. The input signal INPUT 90 PHASE-SS
(a speech waveform, for example) is applied to a bal- SIGNAL DIFFERENCE CIRCUIT OUTPUT
anced modulator along with the first translating or car-
rier frequency. The two normal sidebands appear in the
output of the balanced modulation, but the carrier fre- TRANSLATING P90
quency is balanced out. The purpose of the filter is to
FREQUENCY ~SINGLE FREQ._
select one sideband and reject the other. When the de- Fig. 2-Phasing method of SSB generation.
sired frequency location of the single-sideband signal is
high compared with the original location of the input
signal (e.g., translating speech to the hf region), it be- As this is a balancing method and does not require
comes very difficult to obtain filters that will pass one any sharp cutoff filters, it is possible to generate the de-
sideband and reject the other. To avoid this, the trans- sired sideband in a single translational step regardless
lation is done in several steps so as to ease the filter of how high the final signal frequency may be. However,
requirement. the degree to which the undesired sideband may be
suppressed depends upon accurate balancing and re-
quires very careful control of amplitudes and phases.
INPUT
SIGNAL
BAL.
MOD.
FILTER B AL.
MOD
F ILTER __SS B
OUTPUT
As a practical matter it is quite easy to realize 20-db
suppression, reasonable to expect 30 db, and quite diffi-
FIRST TRANSLATING SECOND TRANSLATING cult to go beyond 40 db. Suppression of 60 to 80 db or
FREQUENCY FREQUENCY
more can be realized using the filter method, but ex-
Fig. 1-Filter method of SSB generation. treme care in maintaining low intermodulation in linear
amplifiers is necessary if this degree of suppression is to
Fig. 1 shows a system using two translational steps. exist in the final radiated signal.
In many radio transmission systems, three to five trans- The design and construction of a wide-band 90
lational steps may be used. The detection problem is phase-difference network is not a familiar art with most
simply an inverse operation; that is, the arrows in Fig. 1 circuit designers, and this often acts as a roadblock to
could be reversed. In detection, balanced modulators using the phasing method.
are not necessary, and ordinary converter circuits are A block diagram showing the new method of single-
satisfactory. sideband signal generation is shown in Fig. 3. The input
The second method, generally called the phasing signal e, is confined to a bandwidth W with the lower
method, is shown in Fig. 2. The input signal is applied to band limit fL as shown in Fig. 4. The band center is fo.
a wide-band 900 phase-difference network. This network
passes all frequencies of the input signal uniformly in fo = fL + W/2. (1)
amplitude. However, the phase response is such that a For convenience let the input signal be expressed as a
sinusoidal input whose frequency falls anywhere within summation of sinusoidal terms.
N
Original manuscript received by the IRE, June 25, 1956.
in).
*
t Formerly with Stanford Res. Inst., Menlo Park, Calif., now ei(t) = , E. cos (o.1t + (2)
with Elec. Eng. Dept., Montana State College, Bozeman, Mont. nl-

Authorized licensed use limited to: University of Canterbury. Downloaded on November 2, 2009 at 21:08 from IEEE Xplore. Restrictions apply.
1 704 PROCEEDINGS OF THE IRE December
SPECTRUM
OF
ea3 2fL
e; AND L.,-,, -41 _lr -F
- _ '.41 10, -#' Iri
IN ea2 W/2
0 fo 2fo-W/2 2fo 2fo + W/2
FREQUENCY
Fig. 5-Spectrum from first balanced modulators.

Fig. 3-Single-sideband generator. have adequate attenuation to eliminate the high-fre-

quency components from the balanced modulators.
Using such a filter the expressions for the filter output
voltages are
N
INPUT ea2 = E. cos [(cn - coo)t + 45J (9)
SIGNAL n=1
SPECTRUM N
-w eb2 = E En sin [(C, - wo)t + 4fn]. (10)
n=l
V277Z77777777
fL fo fL + W These two low-frequency functions are then applied
Fig. 4-Input signal spectrum. to another pair of balanced modulators. However, in
this case the translating frequency co, is the band center
of the desired single-sideband signal. This is generally a
Note that the modulating or carrier frequency of the high frequency compared with any of the frequencies of
first pair of balanced modulators is the center frequency the original signal. The expressions for the outputs of
of the input spectrum. The outputs of the first two this second pair of modulators are
balanced modulators are
ea3 = ea2 cos w,ct (11)
eal = 2ei(t) cos wot (3)
eba = eb2 sin co.t. (12)
ebl - 2ei(t) sin coot, (4)
Substituting (9) and (10) into (11) and (12), and ex-
where panding gives
C0= 27rfo. (5) N E
ea3 =~ E cos [(We + wn - Wo)t + On]
The coefficient 2 is used for convenience and can be n=l 2

considered a property of the balanced modulators. Sub-

stituting (2) into (3) and (4) and expanding gives + - cos [(Cc - con + coo)t - On] (13)
2

N N E
ea= En cos [(n - wo)t + bn] eb= -E cos [(CO, + Wn - COo)t + 4'nJ
n=1 n=l 2

+ En cos [(Wn + Coo) t+ 4.] (6) - [cos,

-OS -Cnn0
+ t-COO n]. (14)
2
N

ebl =

n+1
En sin [(COn oo)t + 4n] Finally, adding (13) and (14) gives the desired single-
sideband output.
+ Ensin [(cO + COn) t+ On)] (7)
e = ea3 + eb3 (15)
The frequencies f, w,1/27r are restricted to the original N
bandwidth W eO =
En cOs [(Rwc + n Co) + 4)n]. (16)
n=1
f L <f n < fL + W. (8)
Note that the frequency normally referred to as the
Hence the spectrum of the signals eai and ebl is as shown carrier corresponds to wc-coo and that the frequency
in Fig. 5. The low-pass filter passes the frequencies from cow is the center of the single sideband. Fig. 6 shows the
zero to W/2. From W/2 to 2fo W/2 there should be no
- spectrum of cO.
signal energy which provides a convenient transition This method of single-sideband generation does not
region for the filter. Above 2fo W/2 the filter should
- need either sharp cutoff filters or wide-band 900 phase-

Authorized licensed use limited to: University of Canterbury. Downloaded on November 2, 2009 at 21:08 from IEEE Xplore. Restrictions apply.
1956 Weaver: A Third Method of Generation and Detection of SSB Signals 1705

SPECTRUM
OF
OUT PUT FREQUENCL fwl
SIGNAL
FREQUE NCY f,,
Fig. 6-Spectrum of output signal.

difference networks. Imperfections in the phasing or

balancing do not result in the presence of the unwanted
sideband in its usual location. Instead, the unwanted
sideband occupies the same band of frequencies as the
desired sideband, except that it is inverted. This is a
very useful property of this system when channel con- 375 a 75500
servation is an important reason for using single-side- INPUT SIGNAL AUOIO FREQUENCY 300-3300 cps
5SF SIGNAL ATgMc CENTER FREOUENCY

band signals. Fig. 7-Single-sideband generator.

Fig. 7 shows the circuit of a single-sideband generator
using this method. The input signal is a typical speech BIBLIOGRAPHY
signal whose energy is confined to a band from 300 to [1] Polkinghorn, F. A., and Schlaack, N. F. "A Single Sideband
3300 cps. Care must be taken in the first pair of balanced Shortwave System for Transatlantic Radiotelephony." Bell
modulators to keep the input signal component (linear System Technical Journal, Vol. 14 (July, 1935) and PROCEEDINGS
OF THE IRE, Vol. 23 (July, 1935), pp. 701-718.
term) from appearing in the output. The two low-pass [21 Oswald, A. A. "A Short-Wave Single-Sideband Radiotelephone
filters pass all frequencies up to 1500 cps and provide System." PROCEEDINGS OF THE IRE, Vol. 26 (December, 1938),
pp. 1431-1454.
adequate attenuation above 2100 cps. In the second pair [31 Roetken, A. A. "A Single-Sideband Receiver for Short Wave
of balanced modulators the rf oscillator signal must be Telephone Service," PROCEEDINGS OF THE IRE, Vol. 26 (Decem-
ber, 1938), pp. 1455-1465.
accurately balanced out to keep it from appearing in the [4] Dome, R. B. "Wide-Band Phase Shift Network." Electronics,
output. Vol. 19 (December, 1946), pp. 122-115.
[5] Bray, W. J., Lillicrap, H. G., and Lowry, W. R. H. "The De-
Two tone tests indicated that undesired signal com- sign of Transmitter Drives and Receivers for Single Sideband."
ponents were all more than 30 db below the desired sig- Journal of the Institution of Electrical Engineers, Vol. 94, Part
IIIA (December, 1947), pp. 298-312.
nals. The input signal level was in the range 0.1 to 1.0 [6] Villard, 0. G. "Simplified Single Sideband Reception." Elec-
volt. Listening tests using speech and music indicated tronics, Vol. 21 (May, 1948), pp. 82-85.
[7] Villard, 0. G. "A High-Level Single Sideband Transmitter."
good quality. No difficulty was encountered in balancing PROCEEDINGS OF THE IRE, Vol. 36, (November 1948), pp.
the modulators or in phasing the translating signals. 1419-1425.
[8] Polkinghorn, F. A. "Commercial SSB Radiotelephone Systems."
The balanced modulators, filters, and transformers can Communications, Vol. 28 (December, 1948), pp. 24-27.
be packaged in a very small unit. As the circuit is bi- [9] Kerwien, A. E. "Design of Modulation Equipment for Modern
Single-Sideband Transmitters." PROCEEDINGS OF THE IRE, Vol.
lateral, it can be used in demodulation as well as in 40 (July, 1952), pp. 797-803.
generation of single-sideband signals. The lack of critical [101 Kahn, L. R. ASingle-Sideband Transmission by Envelope
Elimination and Restoration." PROCEEDINGS OF THE IRE, Vol.
or expensive elements, combined with the ease of ad- 40 (July, 1952), pp. 803-806.
justment and the ruggedness and reliability of a passive [11] Honey, J. F. "Performance of AM and Single Sideband Com-
munications," Tele-Tech., Vol. 12 (September, 1953), pp. 64-66,
circuit (such as the one shown in Fig. 7) makes this 147-149.
method attractive for application in future single-side- [12] Weaver, D. K. Jr. "Design of RC Wide-Band 90-Degree Phase-
Difference Network." PROCEEDINGS OF THE IRE, Vol. 42
band systems. (April, 1954), pp. 671-676.

C..A.5D

Authorized licensed use limited to: University of Canterbury. Downloaded on November 2, 2009 at 21:08 from IEEE Xplore. Restrictions apply.