Atlas Copco Production drilling rigs

Simba 1250-series
Technical specification

Production drilling rig adapted for small- to medium-sized drifts.

Production drilling with tophammer rock drill in the hole range
5189 (102) mm. Different positioning configurations to match the
method used.

Standard features
Rock drill
Atlas Copco COP 1800-series Control system
Dual-damping system for shock wave absorption and Electrical Direct System (EDS)
continuous rock contact for high penetration Anti-jamming system
Lubricated and pressurized mating surfaces giving long
service intervals Carrier
Shank adapters suitable for the given hole range
Mine-adapted carrier for small- to medium-sized drifts with
articulated steering and four-wheel drive
Drilling unit
Mechanized rod handling system General
Feed with hydraulic two-stage cylinder
Front- and rear-mounted stingers Trolley-mounted operator panel
Drill steel support for guidance during collaring and FOPS-approved protective roof
as support during rod handling Electrical cable reel
Working lights on tripods
Positioning unit
Available in three configurations:
-- Simba 1252 with tilt, rotation and pendulum arm
-- Simba 1253 with tilt, rotation and slide table
-- Simba 1254 with tilt, rotation, pendulum arm and slide
table
Accurate and smooth movements
Mine-adapted, sturdy components
 Simba 1250-series

Specifications
ROCK DRILL Electrical system
COP 1838ME Total installed power......................................................65 kW
Main motor at 50 Hz......................................................55 kW
Voltage..................................................................3801,000 V
Shank adapter R32, T38, T45
Frequency..................................................................5060 Hz
Hole diameter 5189 mm Starting method..........star/delta (380690 V) direct (1,000 V)
Impact power 18 kW Thermal overload protection for electric motors
Impact rate 54 Hz Percussion hour meters on A-panel
Hydraulic pressure, max. 230 bar Digital volt/amperage meter in electric cabinet
Rotation motors Separate rotation Phase sequence indicator
Rotation speed 0210/0140 rpm Earth fault indicator
Battery charger
Lub. air consump. (at 3 bar) 5 l/s
Transformer.....................................................................5 kVA
Water consumption 50 l/min Working lights on tripods.................................. 2x200 W, 24V
Weight 171 kg Cable reel, inner/outer diameter.................... 660/1,095 mm
Limit switch for cable reel
FEED
BMH 200 BMH 214 BMH 215 BMH 216 Air system
Compressor...................................................Atlas Copco LE7
Total length 3,160 mm 3,465 mm 3,770 mm Capacity at 5,400 rpm and 7 bar......................................12 l/s
Drill rod length 1,220 mm 1,525 mm 1,830 mm Air pressure gauge
Hole blowing kit with external air
Total length with extractor 3,365 mm 3,670 mm 3,975 mm
Air flow guard

Drilling unit Water system

Rod Handling System, RHS 17................................ 17+1 rods Electric water booster pump
Adaptable to 4, 5 and 6 rods Capacity at 10 bar boost.................................... max 100 l/min
Adaptable to R32, T38, T45 Speedrods Min water inlet pressure................................................... 2 bar
Adaptable to TDS 56 and TDS 64 drill tubes Water pressure gauge
Mechanized drilling up to 32 m Water flow guard
Rock drill lubrication warning kit

Carrier
Positioning system
Engine...........................................................Deutz F5L 912W
Feed extension (with 4 drill steel).............................. 900 mm Power rating at 2,300 rpm..............................................52 kW
Feed extension (with 5 and 6 drill steel)................ 1,200 mm Torque at 1,550 rpm ....................................................248 Nm
Rotary Acurator BHR 30 for 360 ring drilling Fixed seat for tramming, including safety belt
Sliding table BHT 15 gives 1.5 m feed parallel positioning Articulated steering................................... 41 steering angle
Pendulum arm, BHP 12 gives 1.5 m feed parallel positioning Four-wheel drive
in the side walls. Adds further 1.5 m feed parallel positioning FOPS-approved protective roof
upwards/downwards. Hydrostatic power steering system
Stinger backward on feed . ...................................... BSJ 8-115 Hydrodynamic transmission..................................Clark 24000
Stinger forward on feed . ......................................... BSJ 8-115 Front axle .............................................................. DANA 112
Feed dump, drilling.............. +20 forward and -80 backward Rear axle...................................... DANA 112, 10 oscillation
Rig alignment laser....................................................RAL 650 Automatic differential lock on front axle, limited slip
Tyres.........................................................................8.25xR 15
Control system Clearence outside axles....................................................... 15
Hydraulic jacks, front........................................... 2 extendable
Electrical Direct System, EDS Hydraulic jacks, rear...............................................................2
Basic functions such as semi-automatic drilling and Service brakes .2 separate circuits (hydraulically applied, fully
anti-jamming included enclosed wet disc brakes)
Emergency and parking brakes......................................SAHR
Fuel tank, volume............................................................... 60 l
Power pack Electric system..................................................................24 V
Batteries.......................................................................2x70 Ah
Hydraulic pump for percussion, positioning, feed Tramming lights........................................................... 8x70 W
Hydraulic pump for rotation Brake lights
Pumps unloaded at start Illuminated stairs for platform
System pressure, max................................................... 230 bar Central lubrication system
Hydraulic oil tank, volume............................................... 124 l Catalyser
Low oil level indicator and shut-down Silencer
Oil temperature gauge on oil tank, electronically supervised Fire extinguisher
Electric oil filling pump Spirit levels
Filtration, absolute.......................................................... 16 m Gradeability at max load on drive wheels........................... 1:4
Oil filter indicator Tramming speed on flat ground................................ >10 km/h
Water cooled oil cooler in stainless steel Tramming speed on incline 1:8................................... >4 km/h
Mineral hydraulic oil Horn, beacon and reverse alarm
Outlet for communication radio........................................12 V
Rig alignment laser RAL 650
 Simba 1250-series

Specifications
DRILL STEEL
Rock drill Hole diameter, mm Drill rod Shank adapter Guide tube

COP 1838ME 5164 R32 Speedrod R32 TDS 45

COP 1838ME 6476 T38 Speedrod T38 TDS 56/TDS 64

COP 1838HE 7689 T45 Speedrod T45 TDS 64/TDS 76

COP 2550UX* 7689 (T45)* (T45) TDS 64

COP 2550UX* 89102 T51* T51 TDS 76

COP 2550UX* 89102 TDS 64/76* ST58 N/A

*Simba 1253 and 1252 only

Optional equipment
Drilling system Electrical system
Water mist flushing, water oil cooler, external air supply Electrical cable on reel, H07RN-F
Water mist flushing, air oil cooler, external air supply Electrical cable on reel, Buflex
Rock drill lubrication surveillance system Plug PC4
Dry drilling with dust collector Socket PC4
COP 1838MUX, COP 1838HE, COP 1838HUX, Switch gear
COP 2550UX Electrics according to local standards
Working lights on tripods, 2x500 W, 230 V
Positioning system
Angle Reading Instrument, ARI 6C with/without hole Miscellaneous
depth Rod holder for extra drill rods
Hole depth measurement Manual lubrication kit
Thread lubrication kit Rig washing kit
Automatic lubrication for positioning/drilling system Shelf for drill bits and tools
Central lubrication for positioning/drilling system

Power packs
Air cooler

Carrier
Fire suppression system, manual/CheckFire/automatic
 Simba 1250-series

Measurements
SIDE VIEW

Simba 1254
20o

80o Simba 1253

700

C
1915
A
2200

1670

Illustrations and photos in this brochure may show equipment with optional extras. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information.
Copyright 2012, Atlas Copco Rock Drills AB, rebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying of the contents or any part thereof is prohibited.
Simba 1252
1990 1350 1350 1960
B

1810

COVERAGE AREA
SIMBA 1252 SIMBA 1253 SIMBA 1254

945
750 750 750 1500 750

945
945

1500

1150
1150

1150
o 45o 45o
45o 45

1350
1350

1350

235
240

240

1150

800 1500 800

1150

1500
1150

1590
2000
2000 2000 2380

TURNING RADIUS RECOMMENDED CABLE SIZE AND LENGTH

depending on surface Voltage Type Dimension, mm2 Diameter, Length,
mm m
mm Outer 5,100
Inner 2,5002,700 380400 V Buflex 3x70+3G16+2x1.5 37 125

440575 V Buflex 3x50+3G10+2x1.5 32 150

DIMENSIONS
mm Width 2,060 660690 V Buflex 3x35+3G6+2x1.5 28 205

Height tramming (A) 2,660/2,770/2,810 1,000 V Buflex 3x35+3G6+2x1.5 28 205

Height roof up 2,900 G = Protection yellow/green
Recommendations are given for surrounding temperature of 40C.
Length (with BHM 214/215/216) (B) 6,580/6,880/7,180
Ground clearance 260
9851 2133 01c 09/2012

WEIGHT
gross weight

kg Total 12,500