Atlas Copco Long hole drilling rigs

Simba S7 D
Technical specification

A versatile long hole drilling solution adapted for small- to medium-

sized drifts. Drilling with hydraulic tophammer rock drill in the hole
range 5189 mm. Boom-mounted drilling unit for optimized reach
and flexibility.

Standard features
Rock drill Control system
Atlas Copco COP 1800-series Direct Control System (DCS II)
Dual-damping system for shock wave absorption and Damper Pressure Controlled Impact (DPCI)
continuous rock contact for high penetration Rotation Pressure Controlled Feed (RPCF)
Lubricated and pressurized mating surfaces giving long Anti-jamming system
service intervals Angle reading instrument, ARI S7
Shank adapters suitable for the given hole range
Carrier
Drilling unit Mine-adapted carrier for small- to medium-sized drifts with
BMHP 6000-series heavy-duty aluminium hydraulic feed articulated steering and four-wheel drive
Drill steel support for guidance during collaring and Four jacks for stable set-up
as support during rod handling
Front and rear-mounted stinger General
Rod handling system
Operator panel mounted under canopy
FOPS-approved telescopic protective roof
Hydralic boom Working lights on protective roof
BUT 32PD boom with mine-adapted, sturdy components Hydraulically driven water booster pump
Boom mounted drilling unit Hydraulically driven compressor
Accurate and smooth movements Cable reel
Optional cabin
 Simba S7 D

Specifications
ROCK DRILL Electrical system
COP 1838ME
Total installed power......................................................80 kW
Main motor.....................................................................75 kW
Shank adapter R32, TC35, T38, (T45*) Voltage..................................................................3801 000 V
Hole diameter 5189 mm Frequency..................................................................5060 Hz
Impact power 18 kW
Starting method.................................... star/delta (380690 V)
Transformer.....................................................................5 kVA
Impact rate 60 Hz
Working lights, mounted on roof............. 3 x 35 W, 24 V HID
Hydraulic pressure, max. 230 bar Electronic overload protection for electric motors
Rotation motors Separate rotation Digital volt/amperage meter in electric cabinet
Rotation speed 0210 rpm Limit switch for cable reel with signal lamp
Lub. air consump. (at 3 bar) 5 l/s Manual spotlight, left side
Water consumption 50-120 l/min Phase sequence indicator
Weight 170 kg Earth fault indicator
*T45 gives 9 rods in carousel instead of 10 Battery charger
Cable reel
FEED
BMHP 6800 BMHP 6804 BMHP 6805 BMHP 6806 Air system
Compressor...................................................Atlas Copco LE7
Total length 3 141 mm 3 448 mm 3 753 mm Capacity at 5 400 rpm and 7 bar......................................12 l/s
Hole blowing kit with external air
Drill rod length 1 220 mm 1 525 mm 1 830 mm
Lubricated air for the rock drill
Total length with extractor 3 331 mm 3 655 mm 3 960 mm
Adjustable flow/pressure
Air pressure gauge
Air flow guard
Drilling unit
Water system
Rod Handling System, RHS 10................................ 10+1 rods
Adaptable to R32, TC35, T38, (T45) drill rods Hydraulic powered water booster pump.........Flygt PXR411H
Adaptable to 4, 5 and 6 rods Water booster pump max capacity at 12 bar............... 60 l/min
Mechanized drilling up to 20 m Min water inlet pressure, bar...................................................2
Big hole drilling kit Water flow guard

Positioning system Carrier

Feed dump, drilling.............. +24 forward and -79 backward Deutz 4-cylinder, D914 L04, EPA III/COM III (Tier 3/Stage
Feed extension............................................................. 900 mm IIIA) approved 4-stroke prechamber diesel engine
Boom extension........................................................ 1 250 mm Power rating at 2 300 rpm.............................. 58 kW (77.8 hp)
Stinger forward on feed . ...........................................BSJ 4-45 Torque at 1 500 rpm.....................................................270 Nm
Weight, boom only......................................................2 000 kg Articulated steering................................... 40 steering angle
Angle Reading Instrument, ARI S7 Gradeability at max. load on drive wheels.......................... 1:4
Rig Alignment Laser (RAL) Front axle (wide)....................................................... Dana 112
Boom BUT 32PD Rear axle .........................................Dana 112, 7 oscillation
Rear stinger Tyres . .....................................................................9.00 x R20
Clearance outside axles....................................................... 15
Hydraulic jacks, front . ........................................ 2 extendable
Control system Hydraulic jacks, rear...............................................................2
Service brakes..............................................2 separate circuits
Direct Control System, DCS II
Emergency and parking brakes......................................SAHR
- Low pressure hydraulics at operator panel
Fuel tank, volume............................................................... 60 l
Rock drill lubrication warning kit
Electric system..................................................................24 V
Percussion hour meter
Batteries..............................................................2x12 V, 70 Ah
Tramming lights........6 x 40 W 24 V, LED and 2 x 70 w, 24 V
Power pack Automatic differential lock on front axle
12V outlet for communication radio
Hydraulic oil tank, volume, max...................................... 145 l Hydrostatic power steering system
Hydraulic pumps............................................................. 1 unit Horn, beacon and reverse alarm
Filtration......................................................................... 16 m Boots washing arrangement
Operators control panel for rod handling Hydrostatic transmission
Operators control panel for drilling Fixed seat for tramming
Water/Oil cooler in stainless steel Central grease point
Oil temperature meter on oil tank Exhaust catalyser
Hydraulic oil thermostat Illuminated stairs
Electric oil filling pump Four-wheel drive
Pumps unloaded at start Fire extinguisher
Low oil level indicator Swingable seat
Mineral hydraulic oil Hand throttle
Oil filter indicator Brake lights
Safety belt
Halogen
 Simba S7 D

Specifications
DRILL RODS
Rock drill Hole diameter, mm Drill rod Shank adapter Guide tube

COP 1838ME 5164 R32 Speedrod R32 N/A

COP 1838ME/MUX 51-64 TC35 Speedrod TC35 N/A

COP 1838ME/MUX 6476 T38 Speedrod T38 TDS 56

COP 1838HE/HUX 7689 (T45 Speedrod) (T45) TDS 64

noise and vibration

Operator sound pressure level in canopy, drilling, free 106+-6 dB(A) re 20uPa
field (ISO 11201)
Operator sound pressure level in cabin, drilling, 75+- 3 dB(A) re 20uPa
free field (ISO 11201)
Operator sound pressure level working close to machine, 106+-6 dB(A) re 20uPa
drilling, free field
Sound power level (ISO 3744), drilling, free field 126 dB(A) re 1pW

Vibration levels seated in canopy, drilling (ISO 2631-1) 0.1+- 0.15 m/s^2

Vibration levels seated in cabin, drilling (ISO 2631-1) 0.07+- 0.07 m/s^2

Vibration levels standing in canopy, drilling (ISO 2631-1) 0.1+- 0.15 m/s^2

Vibration levels standing in cabin, drilling (ISO 2631-1) 0.07+- 0.07 m/s^2

Optional equipment
Drilling system Electrical system
COP 1638, COP 1838MUX, COP 1838HE, COP 1838HUX Starting method - soft start (not for 1 000 V)
Water mist flushing, water oil cooler, external air supply Electrics according to local standards
Water mist flushing, air oil cooler, external air supply Stainless steel electrical enclosure
Hole blowing kit with internal air Electrical cable on reel, H07RN-F
Working lights, 2x200 W, 24 V
Positioning system / Drilling unit Electrical cable on reel, Buflex
Socket PC4/PC5
Automatic lubrication for positioning system Plug PC4/PC5
Central lubrication for positioning system Switch gear
Thread lubrication kit
Miscellaneous
Power pack
Rod holder for extra drill rods
Heater kit for hydraulic oil tank Shelf for bits and tools
Manual lubrication kit
Water system Ni-Cr piston rods
Water hose reel Rig washing kit
Water hose

Carrier
Fire suppression system ANSUL, checkfire release
Fire suppression system ANSUL, manual release

Cabin
FOPS-approved cabin, noise level <80 dB(A),
height 2 800 mm including:
-- Front window 16 mm
-- Air conditioning unit
-- Fixed seat
-- Boots washing
-- CD/USB player
-- Swingable seat for drilling
Cabin body made of stainless steel
Front window, 24 mm
Electrical heater, 1.2 kW, 230 V (CE)
 Simba S7 D

Measurements
side view TURNING RADIUS
2800

2800

brochure may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information.
Copyright 2011, Atlas Copco Rock Drills AB, rebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos in this
2800

2100

S7
R5000
R2850

40

365
2095 1400 1400
7926

Coverage area
900
Feed extension
6
575 014
7*
4 4
R40 35o 24o (T
35o ilt)
R2840 79 (Tilt)
COVERAGE AREA DRIFTING

50

1500
* parallel coverage
12

4166
35 o
7700

35

3756
o

8173
1460
55

1380
114 360
175 2000
3100

1380
Stinger extension
175 2605 1250

5874

TURNING RADIUS RECOMMENDED drift SIZE

depending on surface Feed Rod Minimun* Maximun**
(h x w) (h x w)
mm Outer 5 000
mm BMHP 6804 1 220 3,3 x 3,3 7,2 x 8,5
Inner 2 850
BMHP 6805 1 525 3,7 x 3,7 7,5 x 8,8
DIMENSIONS
BMHP 6806 1 830 4x4 7,8 x 9,1
mm Width 2 000
* Minimum without extractor, with +200mm
Height tramming, roof down 2 100 ** Maximum with extractor

Height roof up 2 800

Length tramming (with BMHP 6804/05/06) 8 805*/9 112*/9 417*
COP 1838: RECOMMENDED CABLE SIZE AND LENGTH
Ground clearance 335
Voltage Type Dimension, mm2 Diameter, Length,
*+200 mm with extractor mm m

H07RN-F 4G70 49 70
WEIGHT 380400 V
Buflex 3x95+3G16 45 100
gross weight 440 V
H07RN-F 4G70 49 70
Buflex 3x95+3G16 45 100
9851 2641 01c 01/2011

kg Total 11 800 H07RN-F 4G50 44 90

500525 V
Buflex 3x70+3G16 39 135
Boom side 7 800
H07RN-F 4G50 44 90
550575 V
Engine side 4 000 Buflex 3x70+3G16 39 135
H07RN-F 4G35 38 110
660690 V
Buflex 3x50+3G10 33 160
H07RN-F N/A N/A N/A
1,000 V
Buflex 3x35+3G6 29 200
Recommendations are given for surrounding temperature of 40 C and up to a height of 2,000 m.