Estimate For Toll Plaza 16112015

M. P.
PUBLIC WORKS DEPARTMENT, NH DIVISION, INDORE
DETAILED ESTIMATE FOR TOLL PLAZA
1 Name of work :- Detailed Estimate for Toll Plaza of Two Lane Paved Shoulder i/c
Construction of Bridges Culvert in Km. 24-92 on NH-59A (Indore –
Betul Road )
2 Location :- In km. 26/6 & 71/6
3 Provisions :- Following Provision are made in detailed estimate as per IRC - SP:73 -
2007, section 10 :-
1- Location of Toll Plaza (10.2) :-
(i) Land availabilty - n km. 26 & 71 the clear ROW is 30.00 meter
available and remaning extra land required is 30.00 meter, so provision of
land acquition for 300 m x 30 m = 0.90 hectare made in this estimate.
(ii) Stream of traffic on Toll Plaza - In reach of Km. 24 to 92 the main

junctions are in km. 34, 43, 55, 70, so we provide one toll plaza in km.
26/6 & one on km. 71/6, so no leakage from toll plaza points.
(iii) Visibility for approaching traffic - Both location of toll plaza located
at straight reach, so approach for traffic safely visible.
(iv) Resonably away from road intersection and /or rail crossing :- Both
location of Toll Plaza Resonably away from road intersection and /or rail
crossin
(v) Free from Risk of flooding and submergence :- Both toll plaza free
from risk of flodding and submergance.
2- Land for Toll Plaza (10.3) :-

In km. 26 & 71 the clear ROW is 30.00 meter available and remaning
extra land required is 30.00 meter, so provision of land acquition for 300
m x 30 m = 0.90 hectare made in this estimate.
3- Layout and design of Toll Plaza (10.4) :-
Layout and design of Toll Plaza as per IRC - SP 73 : 2007.
4- Toll Booths (10.5) :-

The Toll Booths provisions are as per typical detailes of Toll Booth are
given in figure 10.2 of IRC - SP 73 : 2007.
5- Road Works (10.6) :-

The Road works for Rigid Pavements as per IRC : 58.
6- Traffic Signs (10.7) :-
The Traffic Signs at the Toll Plaza provided as per IRC : 67, as instructed
in IRC - SP 73 : 2007 (for Toll Plaza).
7- Road Marking (10.8) :-
The Road Marking shall be in accordance of with the provision of IRC :
35 .
8- Toll Plaza Complex (10.9) :-
The size of office complex as per minimum requirement of facilities such
as toilet, bathroom, store, rest room, traffic aidpost, medical aidpost etc.
9- Check / Barrier Gate (10.10) :-

A boom barrier electrically operated placed at the exist of each lane.
10- Lighting (10.11) :-

At the Toll Plaza complex continuous and reliable electric supply system
for efficient functioning, made in the estimate, like interier & exterier
lighting, Highmast lighting, lighting for both approaches, canopy lighting,
backup arrangemement, highway lighting arround toll plaza.
11- Water Supply (10.12) :-

Adequate water supply shall be provided for working out water
requirement and internal drainage system, made in the estimate.
12- Fighter Fighting System (10.13) :-
Protection from fire hazarad the adequate fire protection arrangement
made in the estimate.
4 Rates :- The rates are based on Schedule of Rates of Road & Bridge Work w.e.f
03/11/2014 & Building works SOR w.e.f. 01/08/2014 issued by Engineer
In Chief MP PWD Bhopal (MP) and ammended up to date and the rates
which are not included in SOR, has been taken from Acutal Market Rate.
5 Specification :- MORT&H specification for road and bridge with up to date

ammendment , 5th revisions shall be applicable and as per IRC : SP-73,
2007.
M. P. PUBLIC WORKS DEP
DETAILED ESTI
On NH-59A
Location of Toll Plaza - As per IRC SP
SOR Item /
S.No.
Page No.
1 2
10.3
10.4
10.5
10.15.2 /
Page - 181
Building
SOR
SOR Item /
S.No.
Page No.
1 2
10.15.2 /
Page - 181
Building
SOR
10.6
SOR Item /
S.No.
Page No.
1 2
1 3.11 /
Page - 18
2 2.2 / Page
- 13
3 3.4 / Page
- 15
SOR Item /
S.No.
Page No.
1 2
3.13 /
Page -16
4.12 /
Page - 23
6.1 / Page
- 33
SOR Item /
S.No.
Page No.
1 2
6.3
/ Page -
26
6.12 /
Page - 35
SOR Item /
S.No.
Page No.
1 2
4.13 /
Page - 23
12.1 /
Page - 58
12.3 /
Page - 58
13.7 /
Page - 66
SOR Item /
S.No.
Page No.
1 2
13.9 /
Page - 66
12.8 /
Page - 59
12.31 /
Page - 62
8.11 /
Page - 44
10.7
SOR Item /
S.No.
Page No.
1 2
8.7 / Page
- 43
SOR Item /
S.No.
Page No.
1 2
8.17 /
Page - 45
8.28 /
Page - 47
10.8
8.15 /
Page - 44
SOR Item /
S.No.
Page No.
1 2
10.9
10.10
10.11
10.12
10.13
SOR Item /
S.No.
Page No.
1 2
Sub Engineer
PWD NH Sub Division
Indore/Kannod (M.P.)
M. P. PUBLIC WORKS DEPARTMENT,
DETAILED ESTIMATE FOR
On NH-59A (Indore – Betu
Location of Toll Plaza - As per IRC SP-73 2007 SE
Description of Item
3
Land for Toll Plaza
As per Drawing 10.1 (Land Required for Toll Plaza is 300 Meter x 60
Meter = 18000 Square Meter - Land Avilable 300 Meter x 30 Meter =
9000
Total Land Reqiured for Land Acquition = 18000 - 9000 = 9000 Square
Meter = 0.90 Hectare
Layout for Design of Toll Plaza

Typical Layout plan of 2 + 2 Toll Plaza is given in figure 10.1
(Attached)
Toll Booth
Supply and installation of toll booths of size 2.50 x 1.8 with porta cabin
/ container as per drg. & technical specifications directed by the
engineer.
Steel work in built up tubular trusses including cutting, hoisting fixing in
position and applying a priming coat of approved steel primer, welded
and bolted including special shaped washers etc.
complete.
10.16.2 Hot finished seamless type tubes.
(1) For MS Pipe 110 mm 60 meter @ 15.86 Kg/Rmt = 951.60 Kg

Westage 5 %
Description of Item
Toll Plaza Automation System

Providing & constructing of Toll Plaza Automation system at Toll Plaza
location i.e. Automatic lane, closer, toll island, toll lane camera, toll
booth camera, siren, plastic speed breaker, automatic vehicle
conunter & classifier etc.
Amout of Toll Plaza Complex Cost = 5824443.00

Rates as per norms of CPWD New Delhi S. No. 3.64, 3.66 (0.50 %
+ 0.50 % = 1%) of Total Cost of the Toll Plaza complex
(Copy Attached)
Toll booth Protection work

complete.
(1) For MS Pipe 110 mm 26.80 meter @ 15.86 Kg/Rmt

(1) For Toll Both Protection -
4 Nos. x 2.8 x 0.9 x 1.2 @ 15.86 Kg/Rmt
Westage 5 %
Road Work
Description of Item
3
Scarifying existing bituminous surface to a depth of 50 mm by
mechanical means (Scarifying the existing bituminous road surface to
a depth of 50 mm and disposal of scarified material with in all lifts and
lead upto 1000 metres.)
Clearing and Grubbing Road Land (Clearing and grubbing road land
including uprooting rank vegetation, grass, bushes, shrubs, saplings
and trees girth up to 300 mm, removal of stumps of trees cut earlier
and disposal of unserviceable materials and stacking of serviceable
material to be used or auctioned up to a lead of 1000 metres including
removal and disposal of top organic soil not exceeding 150 mm in
thickness.
A) In area of light jungle
Excavation in Soil using Hydraulic Excavator and Tippers with disposal

upto 1000 metres. (Excavation for roadwork in soil with hydraulic
excavator including cutting and loading in tippers, trimming bottom and
side slopes, in accordance with requirements of lines, grades and
cross sections, and transporting to the embankment location with all
lifts and lead upto 1000m as per relevent clauses of section-300 of
specification.
Description of Item
3
Construction of embankment with approved material having CBR>7
obtained from borrow pits with all lifts and leads, transporting to site,
spreading, grading to required slope and compacting to
meetrequirement of table 300-1, 300-2 and as per relevent clauses of
section-300.
Providing crushed stone aggregate, depositing on a prepared surface

by hauling vehicles, spreading and mixing with a motor grader,
watering and compacting with a vibratory roller to clause 410 to form a
layer of sub-base/Base in accordance to Table No. 400-14, 400-15
and as per clause of section 407 of specifications.
(i) For 53 mm maximum size
(34+10)/2 = 22.00
Dry Lean Cement Concrete Sub- base (Construction of dry lean

cement concrete Sub- base over a prepared sub-grade with coarse
and fine aggregate conforming to IS: 383, the size of coarse
aggregate not exceeding 25 mm, aggregate cement ratio not to
exceed 15:1, aggregate gradation after blending to be as per table
600-1, cement content not to be less than 150 kg/ cum, optimum
moisture content to be determined during trial length construction,
concrete strength not to be less than 10 Mpa at 7 days, mixed in a
batching plant, transported to site, laid with a paver with electronic
sensor, compacting with 8- 10 tonnes vibratory roller, finishing and
curing as per clause 601 of specification complete in all respect.
Description of Item
3
Cement Concrete Pavement (Construction of un-reinforced, dowel
jointed, plain cement concrete pavement M-40 grade concrete over a
prepared sub base with cement , coarse and fine aggregate
conforming to IS 383, maximum size of coarse aggregate not
exceeding 25 mm, mixed in a batching and mixing plant as per
approved mix design, transported to site, laid with a fixed form or slip
form paver, spread, compacted and finished in a continuous operation
including provision of contraction, expansion, construction and
longitudinal joints, joint filler, separation membrane, sealant primer,
joint sealant, debonding strip, admixtures as approved, curing
compound, finishing to lines and grades as per drawing as per IRC 15
2011 and as per relevant clauses of section 602 of specifications
complete but excluding cost of steel in dowel bar and tie rods etc.)
Add extra in Item No.6.3, 6.4, 6.6 & 6.10 above for the cost of steel in
dowel bar and tie rod including craddle, laps etc. complete required as
per design.
(I) Mild Steel - Dowel Bar 32 mm @ 300 mm c/c length 500 mm

2 x 5300 x 0.50 x 3.858 x 28 x 0.50 =
(II) Tor steel - Tie Bar - 12 mm Dia 700 mm long & 500 mm c/c (2 x
3300 x 0.70) @ 0.888 Kg /MT
Description of Item
3
Construction of Shoulders with approved material/selected soil i/c
excavation all lifts & leads i/c grading to required slope & camber of
4% and compacting using vibratory roller of 80 to 100 kN static weight
to meet requirement as per relevant clause of 400.
(B) Hard Shoulders (CBR value >12)
RCC Road Side Covered Drain

Excavation for Structures
(Earth work in excavation of foundation of structures as per drawing
and technical specification, including setting out, construction of
shoring and bracing, removal of stumps and other deleterious matter,
dressing of sides and bottom and backfilling with approved material.
as per relevant clauses of section 300 & 2100 in)
(B) Mechanical Means
(i) Depth upto 3 m
Providing Plain cement concrete M-15 nominal mix in foundation as

per relevant clauses of sections 1500, 1700 and 2100.
BOTTOM
SIDES (0.20 + 0.15)/2 = 0.18
Cover
Supplying, fitting and placing HYSD bar reinforcement in substructure

complete as per drawing and technical specifications and as per
relevant clause of section 1600.
AREA=(600X1.10)+(2X600X0.8)+(600X1.10) = 2280 SQM
STEEL @ 5KG/SQM i.e. 2280x5.0 = 11400 Kg
Description of Item
3
Providing weep holes in Brick masonry/Plain/ Reinforced concrete
abutment, wing wall/ return wall with 100 mm dia AC/ PVC pipe,
extending through the full width of the structure with slope of 1V :20H
towards drawing foce. Complete as per drawing and Technical
specifications
Toll Plaza Island

Provdiing and laying Plain/Reinforced cement concrete in open
foundation including form work shuttering etc. complete as per
drawing and technical specifications and as per relevant clauses of
sections 1500, 1700 & 2100 with .
(C) RCC Grade M20
for Other Island

For Central Island
Supplying, fitting and placing un-coated HYSD bar reinforcement in

foundation complete as per drawing and technical specifications and
as per relevant clauses of section 1600.
43.84 @ 80 Kg from Above

Painting Two Coats on New Concrete Surfaces Painting two coats
after filling the surface with synthetic enamel paint in all shades on
new plastered concrete surfaces
Traffic Sign
Description of Item
3
Direction and Place Identification signs with size more than 0.9 sqm
size board. ((Providing and erecting direction and place identification
retroreflectorised sign asper IRC:67 made of high intensity Micro-
Prismatic Grade Sheeting (Type XI) vide clause 801.3.3 fixed over
Aluminium composite material sheet with thermoplastic core of Low
density polyethylene (LDPE) between two thick skins/sheets of
aluminium with overall thickness of 4mm and aluminium skin of
thickness 0.3 on both side, the ACM shall conform to Table 800-1 of
specification and High Intensity Micro Prismatck Grade Sheeting shall
conform to Table 800-3 of specification. The
printing on the high intensity grade sheeting shall conform to Clause
801.3.7 with water based latex optimized transparent ink as specified
by the sheeting manufacturer, supported on composite sign post of
size 75mmx33.55mmx34.99 mm (5mm thick) made of Aluminium
composite material in accordance to IRC 67-2010 fixed to ground by
means of properly designed foundation with M15 grade concrete
4500x4500x600 The ACM sheet shall be fixed to the post with
minimum two number breakaway bolts.
(T1) Cantilever gantry sign for Toll Road strart

(T2) Cantilever gantry sign for Toll Gate 1.0 Km
(T3) Kerb sign for Toll Gate 500 m and toll rates
(T4) Kerb sign for exempt vehicles
(T5) Kerb sign for pictorial depiction of toll rates
(T6) Kerb sign for exempt and over size vehicles lane direction sign
(T7) Sign near the tollbooths displaying toll rates, exempt vehicles and
complaint telephone number & address
(T8) Cantilever gantry sign for toll road ends
Description of Item
3
Road Delineators
Supplying and installation of delineators (road way indicators, hazard
markers, object markers), 80-100 cm high above ground level, painted
black and white in 15 cm wide stripes, fitted with 80 x 100 mm
rectangular or 75 mm dia circular reflectorised panels at the top,
buried or pressed into the ground and confirming toIRC-79 and the
drawings.
At Every 20 meter c/c

Road Markers/Road Stud with Lense Reflector Providing and fixing of
road stud 100x 100 mm, die cast in aluminium, resistant to corrosive
effect of salt and grit, fitted with lense reflectors, installed in concrete
or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and
bedded in a suitable bituminous grout or epoxy mortar, all as per BS
873 part 4:1973
At every 30 meter c/c

At Every 2.00 meter interval
Road Marking
Road Marking with Hot Applied Thermoplastic Compound with
Reflectorising Glass Beads on Bituminous Surface (Providing and
laying of hot applied thermoplastic compound 2.5 mm thick including
reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5
mm is exclusive of surface applied glass beads as per IRC:35 .The
finished surface to be level, uniform and free from streaks and holes
all complete as per clause 803 of specifications.)
Bar Marking
Diagonal Marking (12.0 Sqm)
White Stip
Description of Item
3
Centre Line Marking
Edge Line
Toll Plaza Complex

Check Barrier Gate
Providing and installing electranic barrier gate as per additional
technical specification and as directed by Engineer-in-charge
Lighting
Lighting arrangement at Toll Plaza area inculding High Mast light as
per additional technical standard and as directed by Engineer-in-
charge

Rates as per norms of CPWD New Delhi S. No. 3.2, 3.5, 3.6.1 (5.00
% + 15.00 + 4.00 % = 24.00%) of Total Cost of the Toll Plaza
complex
(Copy Attached)
Rates as per norms of CPWD New Delhi S. No. 2.9.2
(Copy Attached)
Water Supply
Construction of internal electrification, water supply for administration
block, rest house including necessary furniture, IT Equipment etc.
Fire Fightening System

Area of Toll Plaza Complex (G.F. + F.F.)
2 x (11.52 x 12.116) = 279.16 Sqm
Description of Item
3
(Copy Attached)
Sub Engineer
PWD NH Sub Division
NT, NH DIVISION, INDORE
OR TOLL PLAZA
Betul Road )
SECTION 10.2 ON KM. 26/6 & 71/6
No. L (m) B (m) D (m) Unit
4 5 6 7 8
1 0.90 Hectare
1 5.00 Sqm
5 Kg
Kg
4 5 6 7 8
Total Kg
Rmt
Rmt
Kg
Kg
Total Kg
4 5 6 7 8
1 300 7.00 Sqm
1 50 40.00 Sqm
2 125 40.00 Sqm
Hectare
Deduct Hectare
Total Area Hectare
1 300 40.00 0.150 Cum

4 5 6 7 8
1 300 37.00 0.500 Cum
1 50 34.00 0.200
2 125 22.00 0.200
Cum
1 50 34.00 0.150
1 125 22.00 0.150
Cum
4 5 6 7 8
1 50 34.00 0.340
1 125 22.00 0.340
Cum
Mt
Mt
4 5 6 7 8
2 300 3.20 0.690 Cum
2 300.00 1.30 1.00 Cum
2 300.00 1.30 0.15 117.00

4 300.00 0.18 0.85 178.50
2 300.00 1.00 0.15 90.00
TOTAL Cum
Tonne
4 5 6 7 8
300 0.20 Meter
4 23.70 1.800 0.200

1 22.40 1.800 0.200
4 1.30 1.230 0.200
2 1.30 0.150 0.960
Cum
Tonne
6X2 1.30 0.800 Sqm

4 5 6 7 8
2 3.40 1.70
2 2.70 2.30
2 2.00 1.20
2 2.70 2.30
2 3.40 1.70
2 7.00 4.30
2 1.00 1.20
2 1.00 1.20
2 3.40 1.70
Sqm
4 5 6 7 8
4 15 Each
2 10
5 150
Each
2x25 7.50 0.300

5x2 12
2x5 30 0.100
4 5 6 7 8
1 33 3.000 0.100
2 300 0.150
Sqm
As per Estimate Attached Seprately
6 Nos
Sqm
4 5 6 7 8
Sub Divisional Officer Executive Engineer

PWD NH Sub Division PWD NH - Division
Indore/Kannod (M.P.) Indore (M.P.)
6
Quantity
0.90
5.00
4758.00
237.90
Quantity
9
4995.90
26.80
53.60
1275.144
63.76
1338.90
Quantity
2100.00
2000.00
10000.00
12.00
2.10
9.90
1800.00
Quantity
5550.00
340.00
1100.00
1440.00
255.00
412.50
667.50
Quantity
578.00
935.00
1513.00
20.40
4.10
Quantity
1324.80
780.00
117.00
178.50
90.00
385.50
11.40
Quantity
60.00
34.13
8.06
1.28
0.37
43.84
3.51
12.48
Quantity
11.56
12.42
4.80
12.42
11.56
60.20
2.40
2.40
11.56
129.32
Quantity
60.00
20.00
750.00
770.00
112.50
120.00
30.00
Quantity
9
10.000
90.00
362.500
6.00
750.00
Quantity
utive Engineer
D NH - Division
ndore (M.P.)
M. P. PUBLIC WORKS DEPAR
ABSTRACT F
On NH-59A (In
Location of Toll Plaza - As per IRC SP-7
SOR Item /
S.No.
Page No.
1 2
10.3
10.4
10.5
10.15.2 /
Page - 181
Building
SOR
SOR Item /
S.No.
Page No.
1 2
10.15.2 /
Page - 181
Building
SOR
10.6
SOR Item /
S.No.
Page No.
1 2
1 3.11 /
Page - 18
2 2.2 / Page
- 13
3 3.4 / Page
- 15
SOR Item /
S.No.
Page No.
1 2
3.13 /
Page -16
4.12 /
Page - 23
6.1 / Page
- 33
SOR Item /
S.No.
Page No.
1 2
6.3
/ Page -
26
6.12 /
Page - 35
4.13 /
Page - 23
SOR Item /
S.No.
Page No.
1 2
12.1 /
Page - 58
12.3 /
Page - 58
13.7 /
Page - 66
13.9 /
Page - 66
SOR Item /
S.No.
Page No.
1 2
12.8 /
Page - 59
12.31 /
Page - 62
8.11 /
Page - 44
10.7
SOR Item /
S.No.
Page No.
1 2
8.7 / Page
- 43
SOR Item /
S.No.
Page No.
1 2
8.17 /
Page - 45
8.28 /
Page - 47
10.8
8.15 /
Page - 44
SOR Item /
S.No.
Page No.
1 2
10.9
10.10
10.11
10.12
10.13
SOR Item /
S.No.
Page No.
1 2
Sub Engineer
PWD NH Sub Division
M. P. PUBLIC WORKS DEPARTMENT, NH
ABSTRACT FOR TOLL P
On NH-59A (Indore – Betul R
cation of Toll Plaza - As per IRC SP-73 2007 SECT
Description of Item
3
Land for Toll Plaza
Meter = 18000 Square Meter - Land Avilable 300 Meter x 30 Meter =
9000
Meter = 0.90 Hectare

Typical Layout plan of 2 + 2 Toll Plaza is given in figure 10.1 (Attached)
Toll Booth
Supply and installation of toll booths of size 2.50 x 1.8 with porta cabin /
container as per drg. & technical specifications directed by the
engineer.
complete.

Westage 5 %
Description of Item
3
Tota
location i.e. Automatic lane, closer, toll island, toll lane camera, toll
booth camera, siren, plastic speed breaker, automatic vehicle conunter
& classifier etc.

Rates as per norms of CPWD New Delhi S. No. 3.64, 3.66 (0.50 % +
0.50 % = 1%) of Total Cost of the Toll Plaza complex
(Copy Attached)

complete.

4 Nos. x 2.8 x 0.9 x 1.2 @ 15.86 Kg/Rmt
Westage 5 %
Tota
Road Work
Description of Item
3
Scarifying existing bituminous surface to a depth of 50 mm by
mechanical means (Scarifying the existing bituminous road surface to a
depth of 50 mm and disposal of scarified material with in all lifts and
lead upto 1000 metres.)
Clearing and Grubbing Road Land (Clearing and grubbing road land
including uprooting rank vegetation, grass, bushes, shrubs, saplings
and trees girth up to 300 mm, removal of stumps of trees cut earlier
and disposal of unserviceable materials and stacking of serviceable
material to be used or auctioned up to a lead of 1000 metres including
removal and disposal of top organic soil not exceeding 150 mm in
thickness.
###
###
Deduct
Total Area
Excavation in Soil using Hydraulic Excavator and Tippers with disposal
upto 1000 metres. (Excavation for roadwork in soil with hydraulic
excavator including cutting and loading in tippers, trimming bottom and
side slopes, in accordance with requirements of lines, grades and cross
sections, and transporting to the embankment location with all lifts and
lead upto 1000m as per relevent clauses of section-300 of
specification.
Description of Item
3
Construction of embankment with approved material having CBR>7
obtained from borrow pits with all lifts and leads, transporting to site,
spreading, grading to required slope and compacting to
meetrequirement of table 300-1, 300-2 and as per relevent clauses of
section-300.
Providing crushed stone aggregate, depositing on a prepared surface

by hauling vehicles, spreading and mixing with a motor grader, watering
and compacting with a vibratory roller to clause 410 to form a layer of
sub-base/Base in accordance to Table No. 400-14, 400-15 and as per
clause of section 407 of specifications.
(34+10)/2 = 22.00
Dry Lean Cement Concrete Sub- base (Construction of dry lean

cement concrete Sub- base over a prepared sub-grade with coarse and
fine aggregate conforming to IS: 383, the size of coarse aggregate not
exceeding 25 mm, aggregate cement ratio not to exceed 15:1,
aggregate gradation after blending to be as per table 600-1, cement
content not to be less than 150 kg/ cum, optimum moisture content to
be determined during trial length construction, concrete strength not to
be less than 10 Mpa at 7 days, mixed in a batching plant, transported to
site, laid with a paver with electronic sensor, compacting with 8- 10
tonnes vibratory roller, finishing and curing as per clause 601 of
specification complete in all respect.
###
Description of Item
3
Cement Concrete Pavement (Construction of un-reinforced, dowel
jointed, plain cement concrete pavement M-40 grade concrete over a
prepared sub base with cement , coarse and fine aggregate conforming
to IS 383, maximum size of coarse aggregate not exceeding 25 mm,
mixed in a batching and mixing plant as per approved mix design,
transported to site, laid with a fixed form or slip form paver, spread,
compacted and finished in a continuous operation including provision of
contraction, expansion, construction and longitudinal joints, joint filler,
separation membrane, sealant primer, joint sealant, debonding strip,
admixtures as approved, curing compound, finishing to lines and
grades as per drawing as per IRC 15 2011 and as per relevant clauses
of section 602 of specifications complete but excluding cost of steel in
dowel bar and tie rods etc.)
###
Add extra in Item No.6.3, 6.4, 6.6 & 6.10 above for the cost of steel in
dowel bar and tie rod including craddle, laps etc. complete required as
per design.

2 x 5300 x 0.50 x 3.858 x 28 x 0.50 =
(II) Tor steel - Tie Bar - 12 mm Dia 700 mm long & 500 mm c/c (2 x
3300 x 0.70) @ 0.888 Kg /MT
Construction of Shoulders with approved material/selected soil i/c

excavation all lifts & leads i/c grading to required slope & camber of 4%
and compacting using vibratory roller of 80 to 100 kN static weight to
meet requirement as per relevant clause of 400.
Description of Item
3
(Earth work in excavation of foundation of structures as per drawing
and technical specification, including setting out, construction of shoring
and bracing, removal of stumps and other deleterious matter, dressing
of sides and bottom and backfilling with approved material. as per
relevant clauses of section 300 & 2100 in)
(i) Depth upto 3 m
###
Providing Plain cement concrete M-15 nominal mix in foundation as per
relevant clauses of sections 1500, 1700 and 2100.
BOTTOM
SIDES (0.20 + 0.15)/2 = 0.18
Cover
TOTA
Supplying, fitting and placing HYSD bar reinforcement in substructure
complete as per drawing and technical specifications and as per
relevant clause of section 1600.
AREA=(600X1.10)+(2X600X0.8)+(600X1.10) = 2280 SQM
Providing weep holes in Brick masonry/Plain/ Reinforced concrete
abutment, wing wall/ return wall with 100 mm dia AC/ PVC pipe,
extending through the full width of the structure with slope of 1V :20H
towards drawing foce. Complete as per drawing and Technical
specifications
Description of Item
3
Toll Plaza Island
Provdiing and laying Plain/Reinforced cement concrete in open
foundation including form work shuttering etc. complete as per drawing
and technical specifications and as per relevant clauses of sections
1500, 1700 & 2100 with .
(C) RCC Grade M20
for Other Island

For Central Island
###
###
Supplying, fitting and placing un-coated HYSD bar reinforcement in

foundation complete as per drawing and technical specifications and as
per relevant clauses of section 1600.

Painting Two Coats on New Concrete Surfaces Painting two coats after
filling the surface with synthetic enamel paint in all shades on new
plastered concrete surfaces
6X
Traffic Sign
Description of Item
3
Direction and Place Identification signs with size more than 0.9 sqm
size board. ((Providing and erecting direction and place identification
retroreflectorised sign asper IRC:67 made of high intensity Micro-
Prismatic Grade Sheeting (Type XI) vide clause 801.3.3 fixed over
Aluminium composite material sheet with thermoplastic core of Low
density polyethylene (LDPE) between two thick skins/sheets of
aluminium with overall thickness of 4mm and aluminium skin of
thickness 0.3 on both side, the ACM shall conform to Table 800-1 of
specification and High Intensity Micro Prismatck Grade Sheeting shall
conform to Table 800-3 of specification. The
printing on the high intensity grade sheeting shall conform to Clause
801.3.7 with water based latex optimized transparent ink as specified
by the sheeting manufacturer, supported on composite sign post of size
75mmx33.55mmx34.99 mm (5mm thick) made of Aluminium composite
material in accordance to IRC 67-2010 fixed to ground by means of
properly designed foundation with M15 grade concrete 4500x4500x600
The ACM sheet shall be fixed to the post with minimum two number
breakaway bolts.

(T7) Sign near the tollbooths displaying toll rates, exempt vehicles and
complaint telephone number & address
Description of Item
3
Road Delineators
Supplying and installation of delineators (road way indicators, hazard
markers, object markers), 80-100 cm high above ground level, painted
black and white in 15 cm wide stripes, fitted with 80 x 100 mm
rectangular or 75 mm dia circular reflectorised panels at the top, buried
or pressed into the ground and confirming toIRC-79 and the drawings.

Road Markers/Road Stud with Lense Reflector Providing and fixing of
road stud 100x 100 mm, die cast in aluminium, resistant to corrosive
effect of salt and grit, fitted with lense reflectors, installed in concrete or
asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and
bedded in a suitable bituminous grout or epoxy mortar, all as per BS
873 part 4:1973

Road Marking
Road Marking with Hot Applied Thermoplastic Compound with
Reflectorising Glass Beads on Bituminous Surface (Providing and
laying of hot applied thermoplastic compound 2.5 mm thick including
reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5
mm is exclusive of surface applied glass beads as per IRC:35 .The
finished surface to be level, uniform and free from streaks and holes all
complete as per clause 803 of specifications.)
Bar Marking
White Stip
Centre Line Marking
Description of Item
3
Edge Line
Toll Plaza Complex

Check Barrier Gate
Providing and installing electranic barrier gate as per additional
technical specification and as directed by Engineer-in-charge
Lighting
Lighting arrangement at Toll Plaza area inculding High Mast light as per
additional technical standard and as directed by Engineer-in-charge

Rates as per norms of CPWD New Delhi S. No. 3.2, 3.5, 3.6.1 (5.00
% + 15.00 + 4.00 % = 24.00%) of Total Cost of the Toll Plaza
complex
(Copy Attached)
(Copy Attached)
Water Supply
Construction of internal electrification, water supply for administration
block, rest house including necessary furniture, IT Equipment etc.

2 x (11.52 x 12.116) = 279.16 Sqm
(Copy Attached)
Description of Item
Sub Engineer
PWD NH Sub Division
NH DIVISION, INDORE
L PLAZA
l Road )
CTION 10.2 ON KM. 26/6 & 71/6
Unit Quantity Rate (Rs.) Amount (Rs.)
4 5 6 7
Hectare 0.90 4 X 5000000 18000000

Lump Sum
Sqm 5.00 200000 1000000
Kg 4758.00
Kg 237.90
4 5 6 7
Kg 4995.90 109.10 545053
38473
Rmt 26.80
Rmt 53.60
Kg 1275.144
Kg 63.76
Kg 1338.90 109.10 146074
4 5 6 7
Sqm 2100.00 5.00 10500
Sqm 2000.00
Sqm 10000.00
Hectare 12.00
Hectare 2.10
Hectare 9.90 48602.00 481160
Cum 1800.00 55.00 99000

4 5 6 7
Cum 5550.00 178.00 987900
340.00
1100.00
Cum 1440.00 1181.00 1700640
255.00
412.50
Cum 667.50 2714.00 1811595
4 5 6 7
578.00
935.00
Cum 1513.00 6362.00 9625706
Mt 20.40 61069.00 1245808
Mt 4.10 63561.00 260600
Cum 1324.80 223.00 295430

4 5 6 7
Cum 780.00 58.00 45240
117.00 117.00
178.50 178.50
90.00 90.00
Cum 385.50 4777.00 1841534
Tonne 11.40 75415.00 859731
Meter 60.00 192.00 11520

4 5 6 7
34.13
8.06
1.28
0.37
Cum 43.84 5465.00 239586
Tonne 3.51 75306.00 264324
Sqm 12.48 59.00 736

4 5 6 7
11.56
12.42
4.80
12.42
11.56
60.20
2.40
2.40
11.56
Sqm 129.32 14324.00 1852380
4 5 6 7
Each 60.00 277.00 16620
20.00
750.00
Each 770.00 672.00 517440
112.50
120.00
30.00
10.000
4 5 6 7
90.00
Sqm 362.500 637.00 230913
3847264
Nos 6.00 100000.00 600000

Lump Sum
923343
Included in
10.9
Sqm 750.00 279.16 209370

4 5 6 7
COST OF ONE TOLL PLAZA - 47707940
` 477.08LACS
Sub Divisional Officer Executive Engineer

PWD NH Sub Division PWD NH - Division
Indore/Kannod (M.P.) Indore (M.P.)
M. P. PUBLIC
DE
Location of Toll Plaza

SOR Item /
S.No.
Page No.
1 2
10.3
10.4
10.5
10.15.2 /
Page - 181
Building
SOR
SOR Item /
S.No.
Page No.
1 2
10.15.2 /
Page - 181
Building
SOR
10.6
1 3.11 /
Page - 18
SOR Item /
S.No.
Page No.
1 2
2 2.2 / Page
- 13
3 3.4 / Page
- 15
3.13 /
Page -16
4.12 /
Page - 23
SOR Item /
S.No.
Page No.
1 2
6.1 / Page
- 33
6.3
/ Page -
26
SOR Item /
S.No.
Page No.
1 2
6.12 /
Page - 35
4.13 /
Page - 23
12.1 /
Page - 58
12.3 /
Page - 58
SOR Item /
S.No.
Page No.
1 2
13.7 /
Page - 66
13.9 /
Page - 66
12.8 /
Page - 59
12.31 /
Page - 62
8.11 /
Page - 44
SOR Item /
S.No.
Page No.
1 2
10.7
8.7 / Page
- 43
SOR Item /
S.No.
Page No.
1 2
8.17 /
Page - 45
8.28 /
Page - 47
10.8
8.15 /
Page - 44
10.9
SOR Item /
S.No.
Page No.
1 2
10.10
10.11
10.12
10.13
SOR Item /
S.No.
Page No.
1 2
Sub Engineer
PWD NH Sub Division
M. P. PUBLIC WORKS D
DETAILED ES
On NH-
Location of Toll Plaza - As per IRC
Description of Item
3
Land for Toll Plaza
18000 Square Meter - Land Avilable 300 Meter x 30 Meter = 9000
0.90 Hectare

Typical Layout plan of 2 + 2 Toll Plaza is given in figure 10.1 (Attached)
Toll Booth
Supply and installation of toll booths of size 2.50 x 1.8 with porta
container as per drg. & technical specifications directed by the engineer.

and applying a priming coat of approved steel primer, welded and
including special shaped washers etc.
complete.

Westage 5 %

Description of Item
3
i.e. Automatic lane, closer, toll island, toll lane camera, toll booth camera
plastic speed breaker, automatic vehicle conunter & classifier etc.

Rates as per norms of CPWD New Delhi S. No. 3.64, 3.66 (0.50 % + 0
1%) of Total Cost of the Toll Plaza complex
(Copy Attached)

and applying a priming coat of approved steel primer, welded and
including special shaped washers etc.
complete.

4 Nos. x 2.8 x 0.9 x 1.2 @ 15.86 Kg/Rmt
Westage 5 %
Road Work
Scarifying existing bituminous surface to a depth of 50 mm by mechanica
(Scarifying the existing bituminous road surface to a depth of 50 m
disposal of scarified material with in all lifts and lead upto 1000 metres.)
Description of Item
3
Clearing and Grubbing Road Land (Clearing and grubbing road land in
uprooting rank vegetation, grass, bushes, shrubs, saplings and trees gir
300 mm, removal of stumps of trees cut earlier and disposal of unserv
materials and stacking of serviceable material to be used or auctioned
lead of 1000 metres including removal and disposal of top organic
exceeding 150 mm in thickness.
Excavation in Soil using Hydraulic Excavator and Tippers with dispos

1000 metres. (Excavation for roadwork in soil with hydraulic excavator in
cutting and loading in tippers, trimming bottom and side slopes, in acc
with requirements of lines, grades and cross sections, and transporting
embankment location with all lifts and lead upto 1000m as per relevent
of section-300 of specification.
Construction of embankment with approved material having CBR>7 o

from borrow pits with all lifts and leads, transporting to site, spreading, gr
required slope and compacting to meetrequirement of table 300-1, 300-2
per relevent clauses of section-300.
Providing crushed stone aggregate, depositing on a prepared surface by

vehicles, spreading and mixing with a motor grader, watering and com
with a vibratory roller to clause 410 to form a layer of sub-base/B
accordance to Table No. 400-14, 400-15 and as per clause of section
specifications.
Description of Item
3
(34+10)/2 = 22.00
Dry Lean Cement Concrete Sub- base (Construction of dry lean cement c
Sub- base over a prepared sub-grade with coarse and fine aggregate con
to IS: 383, the size of coarse aggregate not exceeding 25 mm, ag
cement ratio not to exceed 15:1, aggregate gradation after blending to be
table 600-1, cement content not to be less than 150 kg/ cum, optimum m
content to be determined during trial length construction, concrete streng
be less than 10 Mpa at 7 days, mixed in a batching plant, transported to s
with a paver with electronic sensor, compacting with 8- 10 tonnes vibrato
finishing and curing as per clause 601 of specification complete in all resp
Cement Concrete Pavement (Construction of un-reinforced, dowel jointe

cement concrete pavement M-40 grade concrete over a prepared sub ba
cement , coarse and fine aggregate conforming to IS 383, maximum
coarse aggregate not exceeding 25 mm, mixed in a batching and mixing
per approved mix design, transported to site, laid with a fixed form or s
paver, spread, compacted and finished in a continuous operation in
provision of contraction, expansion, construction and longitudinal join
filler, separation membrane, sealant primer, joint sealant, debondin
admixtures as approved, curing compound, finishing to lines and grades
drawing as per IRC 15 2011 and as per relevant clauses of section
specifications complete but excluding cost of steel in dowel bar and tie ro
Description of Item
3
Add extra in Item No.6.3, 6.4, 6.6 & 6.10 above for the cost of steel in do
and tie rod including craddle, laps etc. complete required as per design.

2 x 5300 x 0.50 x 3.858 x 28 x 0.50 =
(II) Tor steel - Tie Bar - 12 mm Dia 700 mm long & 500 mm c/c (2 x 3300
@ 0.888 Kg /MT
Construction of Shoulders with approved material/selected soil i/c excav

lifts & leads i/c grading to required slope & camber of 4% and compactin
vibratory roller of 80 to 100 kN static weight to meet requirement as per
clause of 400.

(Earth work in excavation of foundation of structures as per drawi
technical specification, including setting out, construction of shoring and
removal of stumps and other deleterious matter, dressing of sides and
and backfilling with approved material. as per relevant clauses of sectio
2100 in)
(i) Depth upto 3 m
Providing Plain cement concrete M-15 nominal mix in foundation as per

clauses of sections 1500, 1700 and 2100.
BOTTOM
SIDES (0.20 + 0.15)/2 = 0.18
Cover
Description of Item
3
Supplying, fitting and placing HYSD bar reinforcement in substructure c
as per drawing and technical specifications and as per relevant clause of
1600.
AREA=(600X1.10)+(2X600X0.8)+(600X1.10) = 2280 SQM
Providing weep holes in Brick masonry/Plain/ Reinforced concrete ab
wing wall/ return wall with 100 mm dia AC/ PVC pipe, extending through
width of the structure with slope of 1V :20H towards drawing foce. Com
per drawing and Technical specifications
Toll Plaza Island

Provdiing and laying Plain/Reinforced cement concrete in open fou
including form work shuttering etc. complete as per drawing and te
specifications and as per relevant clauses of sections 1500, 1700 & 2100
(C) RCC Grade M20
for Other Island

For Central Island
Supplying, fitting and placing un-coated HYSD bar reinforcement in fou

complete as per drawing and technical specifications and as per relevant
of section 1600.

Painting Two Coats on New Concrete Surfaces Painting two coats after fi
surface with synthetic enamel paint in all shades on new plastered c
surfaces
Description of Item
3
Traffic Sign
Direction and Place Identification signs with size more than 0.9 sqm size
((Providing and erecting direction and place identification retroreflectoris
asper IRC:67 made of high intensity Micro-Prismatic Grade Sheeting (T
vide clause 801.3.3 fixed over Aluminium composite material she
thermoplastic core of Low density polyethylene (LDPE) between tw
skins/sheets of aluminium with overall thickness of 4mm and aluminium
thickness 0.3 on both side, the ACM shall conform to Table 800-1 of spec
and High Intensity Micro Prismatck Grade Sheeting shall conform to Tabl
of specification. The
printing on the high intensity grade sheeting shall conform to Clause 801.
water based latex optimized transparent ink as specified by the s
manufacturer, supported on composite sign post of size 75mmx33.55mm
mm (5mm thick) made of Aluminium composite material in accordance
67-2010 fixed to ground by means of properly designed foundation w
grade concrete 4500x4500x600 The ACM sheet shall be fixed to the p
minimum two number breakaway bolts.

(T7) Sign near the tollbooths displaying toll rates, exempt vehicles and co
telephone number & address
Description of Item
3
Road Delineators
Supplying and installation of delineators (road way indicators, hazard m
object markers), 80-100 cm high above ground level, painted black and
15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia
reflectorised panels at the top, buried or pressed into the ground and co
toIRC-79 and the drawings.

Road Markers/Road Stud with Lense Reflector Providing and fixing of ro
100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt a
fitted with lense reflectors, installed in concrete or asphaltic surface by
hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous
epoxy mortar, all as per BS 873 part 4:1973

Road Marking
Road Marking with Hot Applied Thermoplastic Compound with Reflec
Glass Beads on Bituminous Surface (Providing and laying of hot
thermoplastic compound 2.5 mm thick including reflectorising glass be
250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applie
beads as per IRC:35 .The finished surface to be level, uniform and fr
streaks and holes all complete as per clause 803 of specifications.)
Bar Marking
White Stip
Centre Line Marking
Edge Line
Toll Plaza Complex

Description of Item
3
Check Barrier Gate
Providing and installing electranic barrier gate as per additional te
specification and as directed by Engineer-in-charge
Lighting
Lighting arrangement at Toll Plaza area inculding High Mast light
additional technical standard and as directed by Engineer-in-charge

Rates as per norms of CPWD New Delhi S. No. 3.2, 3.5, 3.6.1 (5.00 %
+ 4.00 % = 24.00%) of Total Cost of the Toll Plaza complex
(Copy Attached)

(Copy Attached)
Water Supply
Construction of internal electrification, water supply for administration blo
house including necessary furniture, IT Equipment etc.

2 x (11.52 x 12.116) = 279.16 Sqm
(Copy Attached)
Description of Item
Sub Engineer
PWD NH Sub Division
ARTMENT, NH DIVISION, INDORE
MATE FOR TOLL PLAZA
(Indore – Betul Road )
P-73 2007 SECTION 10.2 ON KM. 26/6 & 71/6
4 5 6 7 8
1 0.90 Hectare
1 5.00 Sqm
5 Kg
Kg
Total Kg
4 5 6 7 8
Rmt
Rmt
Kg
Kg
Total Kg
1 300 7.00 Sqm

4 5 6 7 8
1 50 40.00 Sqm
2 125 40.00 Sqm
Hectare
Deduct Hectare
Total Area Hectare
1 300 40.00 0.150 Cum
1 300 37.00 0.500 Cum
1 50 34.00 0.200
4 5 6 7 8
2 125 22.00 0.200
Cum
1 50 34.00 0.150
1 125 22.00 0.150
Cum
1 50 34.00 0.340
1 125 22.00 0.340
Cum
4 5 6 7 8
Mt
Mt
2 300 3.20 0.690 Cum
2 300.00 1.30 1.00 Cum
2 300.00 1.30 0.15 117.00

4 300.00 0.18 0.85 178.50
2 300.00 1.00 0.15 90.00
TOTAL Cum
4 5 6 7 8
Tonne
300 0.20 Meter
4 23.70 1.800 0.200

1 22.40 1.800 0.200
4 1.30 1.230 0.200
2 1.30 0.150 0.960
Cum
Tonne
6X2 1.30 0.800 Sqm

4 5 6 7 8
2 3.40 1.70
2 2.70 2.30
2 2.00 1.20
2 2.70 2.30
2 3.40 1.70
2 7.00 4.30
2 1.00 1.20
2 1.00 1.20
2 3.40 1.70
Sqm
4 5 6 7 8
4 15 Each
2 10
5 150
Each
2x25 7.50 0.300

5x2 12
2x5 30 0.100
1 33 3.000 0.100
2 300 0.150
Sqm
As per Estimate Attached Seprately
4 5 6 7 8
6 Nos
Sqm
COST OF ONE TO
`
4 5 6 7 8
For Two No. Toll Plaza At Km. 26/6 & 71/6
Sub Divisional Officer Exe

PWD NH Sub Division PW
Indore/Kannod (M.P.) I
& 71/6
Quantity Rate (Rs.) Amount (Rs.)
9 10 11
0.90 4 X 5000000 18000000

Lump Sum
5.00 200000 1000000
4758.00
237.90
4995.90 109.10 545053
9 10 11
38473
26.80
53.60
1275.144
63.76
1338.90 109.10 146074
2100.00 5.00 10500

9 10 11
2000.00
10000.00
12.00
2.10
9.90 48602.00 481160
1800.00 55.00 99000
5550.00 178.00 987900
340.00
9 10 11
1100.00
1440.00 1181.00 1700640
255.00
412.50
667.50 2714.00 1811595
578.00
935.00
1513.00 6362.00 9625706
9 10 11
20.40 61069.00 1245808
4.10 63561.00 260600
1324.80 223.00 295430
780.00 58.00 45240
117.00
178.50
90.00
385.50 4777.00 1841534
9 10 11
11.40 75415.00 859731
60.00 192.00 11520
34.13
8.06
1.28
0.37
43.84 5465.00 239586
3.51 75306.00 264324
12.48 59.00 736

9 10 11
11.56
12.42
4.80
12.42
11.56
60.20
2.40
2.40
11.56
129.32 14324.00 1852380
9 10 11
60.00 277.00 16620
20.00
750.00
770.00 672.00 517440
112.50
120.00
30.00
10.000
90.00
362.500 637.00 230913
3847264
9 10 11
6.00 100000.00 600000

Lump Sum
923343
Included in
10.9
750.00 279.16 209370
OF ONE TOLL PLAZA - 47707940
477.08LACS
9 10 11
954.16LACS
Executive Engineer
PWD NH - Division
Indore (M.P.)
DETAILED ESTIMATE FOR TOLL PLAZA COMPLEX IN NH 50 A INDORE - BET
Item no
Sl.No Description No. L B H/ D
1 2 3 4 5 6 7
A) UPTO PLINTH LEVEL
1 SOR 2.8 Earth work in excavation by mechanical means (Hydraulic
/ P-23 Excavator)/ manual means in foundation trenches or drains (not
exceeding 1.5 m in width or 10 sqm on plan) including dressing
of sides and ramming of bottoms, lift upto 1.5 m, including
getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m. (No extra lift
is payable if work is done by mechanical means)
All kinds of soil.
footing F1 (Complex) 20 1.80 1.80 2.50

footing F2 (For Boundary Wall) 30 1.50 1.50 2.50
2 SOR Extra for every additional lift of 1.5 m or part thereof in

2.26.1 / excavation. (No extra lift is payable if work is done by
P-26 mechanical means)
All kinds of soil.
3 (PWD Filling available excavated earth (excluding hard rock/Ordinary
S.O.R. rock) in trenches, plinth, sides of foundations etc. in layers not
2.25/ P- exceeding 20cm in depth, consolidating each deposited layer
26) by ramming and watering, lead up to 50 m and lift upto 1.5 m.
Avialable Soil Qty as item3
FOOTING
footing F1 (Complex) -20 1.50 1.50 0.60
footing F2 (For Boundary Wall) -30 1.20 1.20 0.40
P.C.C.
footing F1 (Complex) -20 1.80 1.80 0.15
footing F2 (For Boundary Wall) -30 1.50 1.50 0.15
Columns upto plinth level
C1 -20 0.30 0.50 2.50
C2 -30 0.20 0.40 2.50
4 (S.OR. Supplying and filling in plinth with hard muram/hard copra under
2.28 /P- floors including watering ramming cosolidating in layers not
26) exceeding 20cm in depth and dressing complete.
Ground Floor
Complex Buildlng 1 11.51 12.11 0.60
5 SOR Supplying and filling in plinth with crusher stone dust/ coarse
2.27/ P- sand under floors including, watering, ramming consolidating in
26 layers not exceeding 20cm in depth in layers not exceeding
20cm in depth and dressing complete.
Ground Floor
Complex Buildlng 1 11.51 12.11 0.20
6 S.O.R. Providing and laying in position cement concrete of specified

4.1.2.1/ grade excluding the cost of centering and shuttering - All work
P-45 up to plinth level : 4.1.2 With 40mm nominal size graded stone
aggregate. M 15
4.1.2.1 M 15 - Grade concrete
P.C.C.
Item no
1 2 3 4 5 6 7
7 SOR Reinforced cement concrete work (with 20mm nominal size

5.2.2/ P- graded stone aggregate) in walls (any thickness), including
65 attached pilasters, buttresses, plinth and string courses, fillets,
columns, pillars, posts and struts etc. above plinth level and up
to floor two level excluding cost of centering, shuttering,
finishing and reinforcement :
M 15 –Grade Concrete
Columns upto plinth level
C1 20 0.30 0.50 2.50
C2 30 0.20 0.40 2.50
plinth beam
X beam 1 47.47 0.20 0.40
L beam 1 54.17 0.20 0.40
Curtain wall 1 47.24 0.15 0.40
plinth Slab 1 11.51 12.11 0.10
8 SOR Centering and shuttering including strutting, propping etc.

5.9.1, andremoval of form work for :
P-66
A) Foundations, footings, bases of columns, etc. for concrete
up to plinth level.
footing F1 20 6.00 0.60
footing F2 30 4.80 0.40
9 SOR Centering and shuttering including strutting, propping etc.

5.9.2 P- andremoval of form work for : Walls (any thickness) including
66 attached pilasters butteresses, plinth beams and string courses
etc.up to plinth level.
Columns upto plitn level

C1 20 1.60 2.50
C2 30 1.20 2.50
plinth beam
X beam 1 47.47 0.30
L beam 1 54.17 0.30
Curtain wall 1 47.24 0.40
10 SOR Reinforcement for R.C.C. work including straightening, cutting,

5.16.6 / bending, placing in position and binding including cost of
P-68 binding wire up to floor two level including all wastage etc.
complete..
Thermo-Mechanically Treated bars.(TMT)

Total RCC Qty 120kg/cum.
B) SUPER STRUCTURE
11 SOR Reinforced cement concrete work (with 20mm nominal size
5.2.1/P6 graded stone aggregate) in walls (any thickness), including
5 attached pilasters, buttresses, plinth and string courses, fillets,
columns, pillars, posts and struts etc. above plinth level and up
to floor two level excluding cost of centering, shuttering,
finishing and reinforcement :
Item no
1 2 3 4 5 6 7
Columns upto ground floor roof
C1 20 0.30 0.50 3.15
C2 30 0.20 0.40 3.15
Roof beam
X beam 1 47.47 0.20 0.50
L beam 1 54.17 0.20 0.50
Ground floor roof 1 11.51 12.16 0.125
12 SOR 5.3 Reinforced cement concrete work (with 20mm nominal size
/ P- 65 graded stone aggregate) in beams, suspended floors, roofs
having slope of any degree landings, balconies, shelves,
chajjas, lintels, bands, plain window sills, staircases and spiral
stair cases above plinth level and up to floor two level excluding
the cost of centering, shuttering, finishing and reinforcement in
concrete grade.
Ground floor
Staircase
Staircase waist slab 150 thk. 2 1.4 3.4 0.15
Staircase Landing 1 3 1.4 0.15
Staircase StepsTread 18 0.3 1.4 0.02
Lintels 1 101.64 0.20 0.30
Chajja 1 47.24 0.60 0.10
13 SOR Reinforcement for R.C.C. work including straightening, cutting,

5.16.6 / bending, placing in position and binding including cost of
P-68 binding wire up to floor two level including all wastage etc.
complete.
Thermo-Mechanically Treated bars.(TMT)

120 Kg per cum of RCC qty
14 SOR Centering and shuttering including strutting, propping etc. and
5.9/P 66 removal of form for
5.9.3 Suspended floors, roofs, landings, balconies and access
platform.
5.9.4 Shelves (Cast in situ)
5.9.5 Lintels, beams, girders, bressumers and cantilevers.
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts.
15 SOR Brick work with fly ash lime bricks (FALG Bricks) conforming to
6.7.1.2/ IS:12894-2002, in super structure above plinth level up to floor
P-86 II level in : Cement mortar 1:6 (1 cement : 6 sand) 6.7.1.2
.
Ground Floor
1 92.67 0.20 2.75
1 47.24 0.20 0.90
16 SOR Extra for brick work in superstructure above floor two level for
6.11/ P- each additional floor or part thereof respective item..
86
Perapet wall
Item no
1 2 3 4 5 6 7
17 SOR Providing and fixing pressed steel door frames conforming to
10.13 IS: 4351 manufactured from commercial mild steel sheet
/P179 including hinges, jamb, lock jamb, bead and if required angle
threshold of mild steel angle of section 50x25mm, or base ties
of 1.60 mm pressed mild steel welded or rigidly fixed together
by mechanical means, including M.S. pressed butt hinges,
2.5mm thick with mortar guards, lock strike-plate and shock
absorbers as specified filling the frame with Cement Concrete
1:3:6 at site before fixing (cost of concrete to be paid
separately) and applying a coat of approved steel primer after
pre-treatment of the surface as directed by Engineer-in-charge:
10.13.2 Profile C of 1.60mm thick single rebate of size 100mmx50mm
10.13.2. Fixing with adjustable lugs with split end tail to each jamb.
1
GROUND FLOOR
D1 2 6.10
D2 6 5.20
D3 5 5.05
W1 4 5.70
W2 2 6.00
W3 2 4.96
V1 2 2.95
V2 2 5.03
18 SOR Providing and fixing to existing door frames

9.163
/P161
9.163.1 24 mm thick factory made PVC door shutters made of styles
and rails of a uPVC hollow section of size 59x24 mm and wall
thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides.
The styles and rails mitred and joint at the corners by means of
M.S. galvanised/plastic brackets of size 75x220 mm having wall
thickness 1.0 mm and stainless steel screws. The styles of the
shutter reinforced by inserting galvanised M.S. tube of size
20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail
made up of 'H' section, a uPVC hollow section of size 100x24
mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter
styles by means of plastic/galvanised M.S. 'U' cleats. The
shutter frame filled with a uPVC multi-chambered single panel
of size not less than 620 mm, having over all thickness of 20
mm and 1 mm (± 0.1 mm) wall thickness. The panels filled
vertically and tie bar at two places by inserting horizontally 6
mm galvanised M.S. rod and fastened with nuts and washers,
complete as per manufacturer's specification and direction of
Engineer-in-charge. (For W.C. and bathroom door shutter).
D3 5 0.75 2.15
19 SOR Providing and fixing ISI marked flush door shutters conforming
9.19 /P- to IS: 2202 (Part I) non-decorative type, core of block board
136 construction with frame of 1st class hard wood and well
matched commercial 3 ply veneering with vertical grains or
cross bands and face veneers on both faces of shutters of such
as duro board, century or equivelant make..
9.19.1 35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws.
D1 2 1.80 2.15
Item no
1 2 3 4 5 6 7
D2 6 0.90 2.15
20 SOR Extra for providing lipping with 2nd class teak wood battens 25
9.21/P- mm minimum depth on all edges of flush door shutters (over all
136 area of door shutter to be measured).
Qty same as flush door 1
21 SOR Extra for Providing and fixing flush doors with decorative
9.20/ P- veneering instead of non decorative ISI marked flush door
136 shutters conforming to IS: 2202 (Part I).
9.20.1 On one side only.
Qty same as flush door 1
22 SOR Providing and fixing aluminium sliding door bolts ISI marked
9.109 anodised (anodic coating not less than grade AC 10 as per IS :
/P148 1868) transparent or dyed to required colour or shade with nuts
and screws etc. complete:
9.109.1 300x16 mm 26
23 SOR Providing and fixing aluminium tower bolts ISI marked anodised
9.110 / (anodic coating not less than grade AC 10 as per IS : 1868 )
P-149 transparent or dyed to required colour or shade with necessary
screws etc. complete.
9.110.3 200x10 mm
Door D 52
24 SOR Providing and fixing aluminium hanging floor door stopper ISI
9.114 marked anodised (anodic coating not less than grade AC 10 as
/P-149 per IS : 1868) transparent or dyed to required colour and shade
with necessary screws etc. complete.
9.114.2 Twin rubber stopper
Door D 26
25 SOR Providing and fixing aluminium extruded section body tubular
9.95/ type universal hydraulic door closer (having brand logo with ISI,
P147 IS : 3564, embossed on the body, door weight upto 36 kg to 80
kg and door width from 701 mm to 1000 mm) with double
speed adjustment with necessary accessories and screws etc.
complete..
13
26 SOR Providing and fixing double action hydraulic floor spring of

21.5/P- approved brand and manufacture IS : 6315 marked, for doors
363 including cost of cutting floors as required, embedding in floors
and cover plates with brass pivot and single piece M.S. sheet
outer box with slide plate etc.complete as per the direction of
Engineer-in-charge.
21.5.1 With stainless steel cover plate - minimum 1.25 mm thickness. 2
27 SOR it Providing fixing aluminium round shape handle of outer dia

21.16/P 100mm with SS screws etc. complete as per direction of
365 Engineer-in-charge
21.16.1 Anodized (AC15 ) aluminium
26
Item no
1 2 3 4 5 6 7
28 SOR it Providing and fixing hand rail of approved size by welding etc.
10.23/p- to steel ladder railing, balcony railing, staircase railing and
182 similar works, including applying a priming coat of approved
steel primer.
10.23.1 M.S. tube.
10 kg per sqm.
Stair 1 9.5 0.9
Balcony 1 50 0.9
29 SOR it Welding by gas or electric plant including transportation of plant

10.21/P- at site etc. complete.
182
5000
30 S.O.R.1 6 mm cement plaster of mix :

3.8/ P -
244
13.8.1 1:3 (1 cement: 3 sand)
31 sor 12 mm cement plaster of mix :
13.1 /P-
244 1:6 (1 cement: 6 sand)
13.1.2
Gr. Floor
32 3.89 3.03
6 12.11 3.03
LESS
D1 -2 1.8 2.15
D2 -6 0.9 2.15
D3 -5 0.75 2.15
1 47.24 0.90
32 sor 15 mm cement plaster on rough side of single or half brick wall.

13.2 /P
244 1:6 (1 cement: 6 sand).
13.2.2
Gr. Floor
1 47.24 8.50
LESS
W1 -4 1.65 1.2
W2 -2 1.8 1.2
W3 -2 1.28 1.2
34 SOR Providing and laying integral cement based water proofing

22.7.1 / treatment including preparation of surface as required for
P-373 treatment of roofs ,balconies, terraces etc consisting of
following operations: a) Applying a slurry coat of neat cement
using 2.75kg/sqm. of cement admixed with water proofing
compound conforming to IS. 2645 and approved by
Engineer-in-charge over the RCC slab including adjoining walls
upto 300mmheightincluding cleaning the surface before
treatment.
Item no
1 2 3 4 5 6 7
b) Laying brick bats with mortar using broken bricks/brick bats
25 mm to 115mm size with 50% of cement mortar 1:5 (1
cement : 5 sand) admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge
over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :
5 sand ) admixed with water proofing compound conforming to
IS : 2645 and approved by Engineer-in-charge to required slope
and treating similarly the adjoining walls upto 300 mm height
including rounding of junctions of walls and slabs.
c) After two days of proper curing applying a second coat of

cement slurry using 2.75kg/ sqm of cement admixed with water
proofing compound conforming to IS : 2645 and approved by
Engineer-in-charge.
d) Finishing the surface with 20 mm thick jointless cement
mortar of mix 1:4 (1 cement :4 sand) admixed with water
proofing compound conforming to IS : 2645 and approved by
Engineer-in-charge including laying glass fibre cloth of
approved quality in top layer of plaster and finally finishing the
surface with trowel with neat cement slurry and making pattern
of 300x300 mm square 3mm deep.
e) The whole terrace so finished shall be flooded with water for

a minimum period of two weeks for curing and for final test. All
above operations to be done in order and as directed and
specified by the Engineer-in-Charge : (with 5 years service
guarantee)
22.7.1 With average thickness of 120mm and minimum thickness at

khurra as 65 mm.
Toilet 2 3.89 1.90
35 Sor Providing and fixing M.S. grills of required pattern in frames of

9.43/ P- windows etc. with M.S. flats, square or round bars etc. including
140 priming coat with approved steel primer all complete.
9.43.1 Fixed to steel windows by welding.

Total Weight = 95.56x25.0Kg/Sqm
Windows
W1 4 1.65 1.2
W2 2 1.8 1.2
W3 2 1.28 1.2
Total
Sqm
36 SOR Providing and fixing chicken mesh as per ISI specification and
13.27/P- in the required width with 50mm long Bombay nails on vertical
247 and horizontal junctions of RCC and brick wall including
scaffolding and all lead and lift etc. complete before plastering
upto 10 meter height.
34 8.90 0.90
37 PWD Providing and fixing Ist quality ceramic glazed wall tiles
S.O.R. conforming to IS : 15622 (having thickness 6 to 7mm) of
11.48 approved make in all Colours shades, such as burgundy, Bottle
/P- 204 green, Black of size 300x450mm or more in skirting, risers of
steps and dados over 12 mm thick bed of cement Mortar 1:3 (1
cement : 3 sand) and jointing with grey cement slurry @ 3.3kg
per sqm including pointing in white cement mixed with pigment
of matching shade complete.
Item no
1 2 3 4 5 6 7
Ground floor & First Floor
1 3.89 1.94
2 3.89 2.10
2 1.94 2.10
Less door -2 0.75 2.10
38 PWD Providing and laying rectified Glazed Ceramic floor tiles

S.O.R. 300x300 mm or more (having thickness 9 to 10mm) of 1st
11.49 quality conforming to IS : 15622 of approved make in colours
/P- 205 White, Ivory, Grey, Fume Red Brown, laid on 20mm thick
cement mortar 1:4 (1 Cement : 4 sand) including grouting the
joints with white cement and matching pigments etc., complete.
1 3.89 1.94
39 11.34/p- Kota stone slab flooring over 20 mm (average) thick base laid
203 over and jointed with grey cement slurry mixed with pigment to
match the shade of the slab including rubbing and polishing
complete with base of cement mortar 1 : 4 (1 cement : 4
sand) :
11.34.1 25 mm thick.
Ground floor
1 11.51 12.11
40 SOR Kota stone slabs 20 mm thick in risers of steps, skirting, dado

11.35/ and pillars laid on 12 mm (average) thick cement mortar 1:3 (1
P-203 cement 3 sand) and jointed with grey cement slurry mixed with
pigment to match the shade of the slabs, including rubbing and
polishing complete.
Ground floor
Staircase
Tread 36 1.20 0.30
Riser 36 1.20 0.15
41 SOR Applying priming coat :

13.58/
P-250
13.58.1 With ready mixed pink/Grey primer of approved brand and
manufacture on wood work (hard & soft wood).
Ground Floor
Doors
D1 2 1.8 2.15
D2 6 0.9 2.15
42 SOR Painting with synthetic enamel paint of approved brand and

13.69/ manufacture of required colour to give an even shade:
P-252
13.69.1 Two or more coats on new work over an under coat of suitable
shade with ordinary paint of approved brand and
manufacture.
Ground Floor
Doors
D1 2 1.8 2.15
D2 6 0.9 2.15
Item no
1 2 3 4 5 6 7
43 SOR13. Providing and applying white cement based putty of average
41/ P- thickness 1 mm, of approved brand and manufacturer, Like birla
248 white /JK white or equivalent, over the plastered wall surface to
prepare the surface even and smooth i/c all cost of material,
labour and scaffold etc in all position complete.
qty of 15 mm plaster
44 SOR13. Providing and applying special putty in two coats based
42/ P- materials varnish, Belgium chalk, turpentile oil, white
248 paint,safeda including sand papering for making the surface
smooth for applying any or vinyl paints including all cost of
material and labour etc complete.
qty as 12mm
45 SOR Wall painting with plastic emulsion paint of approved brand and
13.49/ manufacture to give an even shade: Two or more coats on new
P-249 work
13.49.1 Two or more coats on new work
qty of 12 mm
46 Sor Finishing walls with Premium Acrylic Smooth exterior paint with
13.56/ Silicone additives of required shade.
P-250
13.56.1 New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over
and including priming coat of exterior primer applied @ 2.20 kg/
10 sqm).
qty of 18 mm plaster
47 Sor Distempering with oil bound washable distemper of approved

13.47/ brand and manufacture to give an even shade.
P-249
13.47.1 New work (two or more coats) over and including water
thinnable priming coat with cement primer.
qty of 6mm ceiling /conc. Surface
48 SOR Providing and fixing aluminium work for doors, windows,
21.1.1 / ventilators and partitions with extruded built up standard tubular
P-362 sections/ appropriate Z sections and other sections of approved
make conforming to IS: 733 and IS : 1285, fixed with rawl plugs
and screws or with fixing clips, or with expansion hold fasteners
including necessary filling up of gaps at junctions, at top,
bottom and sides with required PVC/neoprene felt etc.
Aluminium sections shall be smooth, rust free, straight, mitred
and jointed mechanically wherever required including cleat
angle, Aluminium snap beading for glazing / paneling,C.P. brass
/ stainless steel screws, all complete as per architectural
drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasteners to be paid for separately).
21.1.1.2 Powder coated aluminium (minimum thickness of powder

coating 50 micron):
For Fixed Portion @ 5 kg / sqm.

W1 4 1.65 1.2
W2 2 1.8 1.2
W3 2 1.28 1.2
V1 2 0.9 0.57
V2 2 1.94 0.57
Item no
1 2 3 4 5 6 7
49 SOR For shutters of doors, windows & ventilators including providing
21.1.2/3 and fixing hinges/ pivots and making provision for fixing of
62 fittings wherever required including the cost of PVC / neoprene
gasket required (Fittings shall be paid for separately).
21.1.2.2 Powder coated aluminium (minimum thickness of powder

coating 50 micron):
5kg. / sqm.
Same as quantity from item no 57
50 SOR Providing and fixing glazing in aluminium door, window,
21.3/ P- ventilator shutters and partitions etc. with EPDM rubber/
363 neoprene gasket etc. complete as per the architectural
drawings and the directions of engineer-in-charge . (Cost of
aluminium snap beading shall be paid in basic item) :
21.3.2 With float glass panes of 5.50 mm thickness

Window qty
C WATER SUPPLY / SANITORY

51 17.1/ P- Providing and fixing water closet squatting pan (Indian type
290 W.C. pan) with 100mm sand cast Iron P or S trap, uPVC P or S
trap, 10 litre low level white P.V.C. flushing cistern, including
flush pipe, with manually controlled device (handle lever)
conforming to IS : 7231, with all fittings and fixtures complete
including cutting and making good the walls and floors
wherever required :
17.1.1 White Vitreous china Orissa pattern W.C. pan of size

580x440mm with integral type foot rests.
2
52 S.O.R. Providing and fixing white vitreous china flat back half stall
17.7 /P- urinal of size 580x380x350mm with white PVC automatic
291 flushing cistern, with fittings, standard size C.P. brass flush
pipe, spreaders with unions and clamps (all in C.P. brass) with
waste fitting as per IS : 2556, C.I. trap with outlet grating and
other couplings in C.P. brass including painting of fittings and
cutting and making good the walls and floors wherever required
17.7.3 Range of three half stall urinals with 10 litre P.V.C.

automatic flushing cistern. 3
53 17.3/ P- Providing and fixing white vitreous china pedestal type water
290 closet (European type) with seat and lid, 10 liter low level white
vitreous china flushing cistern, C.P. flush bend with fittings,
C.I.brackets, 40mm flush bend, overflow arrangement with
specials of standard make and mosquito proof coupling of
approved municipal design complete including painting of
fittings and brackets, cutting and making good the walls and
floors wherever required :
17.3.1 a) W.C. pan with white plastic seat and lid. 3

54 S.O.R.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P.
7.11 brass pillar taps,32 mm C.P. brass waste of standard pattern,
/ P- including painting of fittings and brackets, cutting and making
292 good the walls wherever required
17.11.1 White Vitreous China Wash basin size 630x450 mm with a pair
of 15 mm C.P. brass pillar taps. 3
55 17.83/ Providing and fixing PTMT towel rail complete with brackets
P-304 fixed to wooden cleats with CP brass screws with concealed
fitting arrangement of approved quality and color.
17.83.2 600mm long towel rail with total length of 645mm, width 78mm
and effective height of 88mm, weighing not less than 190gms. 3
Item no
1 2 3 4 5 6 7
56 17.67/P- Providing and fixing 600x450 mm beveled edge mirror of
303 superior glass (of approved quality) complete with 6 mm thick
hard board ground fixed to wooden cleats with C.P. brass
screws and washers complete
3
57 18.8/P- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)
316 pipes, having thermal stability for hot & cold water supply
including all CPVC plain & brass threaded fittings including
fixing the pipe with clamps at 1.00 m spacing. This includes
jointing of pipes & fittings with one step CPVC solvent cement
and testing of joints complete as per direction of Engineer in
Charge. Concealed work including cutting chases and making
good the walls etc.
18.8.1 a) 15mm nominal bore 50

18.8.2 b) 20mm nominal bore 40
18.8.3 c) 25mm nominal bore 30
18.8.4 d)32mm nominal bore 40
58 18.9/P- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)
316 pipes, having thermal stability for hot and cold water supply
including all CPVC plain and brass threaded fittings. This
included jointing of pipes and fittings with one step CPVC
solvent cement, trenching, refilling and testing of joints
complete as per direction of Engineer in Charge.
External work

18.9.4 d)32mm nominal bore 30
18.9.5 e)40mm nominal bore 30
18.9.6 f)50mm nominal bore 20
59 18.52/P- Providing and fixing C.P. brass bib cock of approved quality
330 conforming to IS:8931
60 18.55/P- Providing and fixing C.P. brass stop cock (concealed) of
330 standard design and of approved make conforming to IS:8931.

61 18.32/P Providing and fixing gun metal gate valve with C.I. wheel of
325 approved quality (screwed end) :
18.32.4 d) 50mm nominal bore 5
62 18.35/P- Providing and fixing ball valve (brass) of approved quality, High
326 or low pressure, with plastic floats complete :
63 18.49/P- Providing and placing on terrace (at all floor levels)

330 polyethylene water storage tank ISI : 12701 marked with cover
and suitable locking arrangement and making necessary holes
for inlet, outlet and overflow pipes but without fittings and the
base support for tank.
4 1000
64 19.7/P- Providing and fixing square-mouth S.W. gully trap class SP1
341 complete with C.I. grating brick masonry chamber with water
tight C.I. cover with frame of 300 x300 mm size (inside) the
weight of cover to be not less than 4.50 kg and frame to be not
less than 2.70 kg as per standard design :
Item no
1 2 3 4 5 6 7
19.7.1 100x100 mm size P type
19.7.1.1 With well burnt bricks 3
65 19.4/P- Providing and laying below ground unplasticised PVC pipe to

340 with stand working pressure of 4 kg/cm2 soild waste pipes
confirming to IS:13592 and IS:4985 including jointing with seal
ring confirming to IS :5282 leaving 10mm gap for thermal
expansion all necessary fittings etc. complete. Excavation to be
paid seperataly.
151.4
19.4.1 110 mm diameter OD
20nos X6m
66 19.3/P- Providing and laying cement concrete 1:5:10 (1 cement : 5
340 sand : 10 graded stone aggregate 40 mm nominal size) upto
haunches of S.W. pipes including bed concrete as per standard
design :
19.3.1 100 mm diameter S.W. pipe
a to g
120
67 Sor12.3 Providing and fixing on wall face Unplasticised Rigid PVC rain
2/P223 water pipes conforming to IS : 13592 Type A including jointing
with seal ring conforming to IS : 5382 leaving 10 mm gap for
thermal expansion.
(i) Single socketed pipes(SOR12.32/P-223)
13.32.2 110 mm diameter (minimum wall thickness 2.2mm)

60
68 SOR12. Providing and fixing on wall face unplasticised - PVC moulded
33 /P- fittings/ accessories for unplasticised Rigid PVC Rain water
146 pipes conforming to IS : 13592 Type A including jointing with
seal ring conforming to IS :5382 leaving 10 mm gap for thermal
expansion. .
(a) Plain Bend 87.5*

(i) 75 mm dia
(PWD S.O.R. 12.33.5.1 / p- 224)
(ii) 110 mm dia
(PWD S.O.R. 12.33.5.1 / p- 224)
(b) Plain bend of 45*shoes
(i) 75 mm dia
(PWD S.O.R. 12.33.6.1/ P- 223)
(ii) 110 mm dia
(PWD S.O.R. 12.33.6.2 / P- 223)
(c) Coupler (PWD S.O.R. 12.33.1/ p-223)
(i) 75 mm dia
(PWD S.O.R. 12.33.1.1/ p-223)
(ii) 110 mm dia
(PWD S.O.R. 12.33.1.2/ p- 223)
(d) Single Tee with door (PWD S.O.R. 12.33.3/ P- 223)
(i) 75x75x75 mm
(PWD S.O.R. 12.33.3.1 / p-223)
(ii) 110x110x110 mm
(PWD S.O.R. 12.33.3.2 / p-223)
sor Providing and fixing M.S. stays and clamps for sand cast
17.56/P- iron/centrifugally cast (spun) iron pipes of diameter :
300
(I) 100 mm
(PWD S.O.R. 17.56.1/ p. 300)
(ii) 75 mm
Item no
1 2 3 4 5 6 7
(PWD S.O.R. 17.56.2/ p. 300)
69 SOR19. Constructing brick masonry manhole in cement mortar 1:4 ( 1
9/P-342 cement : 4 sand ) R.C.C. top slab with Cement Concrete 1:2:4
mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm
nominal size), foundation concrete 1:4:8 mix (1 cement : 4 sand
: 8 graded stone aggregate 40mm nominal size) inside
plastering 12mm thick with cement mortar 1:3 (1 cement : 3
sand) finished with floating coat of neat cement and making
channels in cement concrete 1:2:4 (1 cement : 2 sand : 4
graded stone aggregate 20mm nominal size) finished with a
floating coat of neat cement complete as per standard design :
19.9.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with
frame (light duty) 455x610 mm internal dimensions total weight
of cover and frame to be not less than 38 kg (weight of cover 23 4
kg and weight of frame 15 kg) :
19.9.1.1 With well burnt bricks
19.9.2 Inside size 120x90 cm and 90 cm deep including C.I. cover with
frame (medium duty) 500 mm internal diameter, total weight of
cover and frame to be not less than 116 kg (weight of cover 58
kg and weight of frame 58 kg) :
19.9.2.1 With well burnt bricks 1
70 Sor Extra for depth for manholes.
19.10/
P-343
19.10.1 Size 90x80 cm 4
19.10.1.
1 With well burnt bricks
19.10.2 Size 120x90 cm 2
19.10.2.
1 With well burnt bricks
71 Sor Extra depth for circular type manhole 1.22m internal dia (at
19.14/ bottom) beyond 1.68 m to 2.29 m : .
P-344
19.14.1 With well burnt bricks 2
72 S.O.R. Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm
19.30 P. dry brick honey comb shaft with bricks of class designation 75
347 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as
per standard design.
1
19.30.1 With well burnt bricks
73 sor Providing and fixing on wall face Unplasticised - PVC moulded
12.33 / fittings/ accessories for Unplasticised Rigid PVC rain water
P-223 pipes conforming to IS : 13592 Type A including jointing with
seal ring conforming to IS : 5382 leaving 10 mm gap for thermal
expansion.
12.33.4 Single tee without door

12.33.4.
110x110x110 mm(minimum wall thickness 2.2mm)
2 4
74 17.32/
P-295 Providing and fixing soil, waste and vent pipes :
17.32.2
75 mm dia Pipe minimum wall thickness 5mm for saptic tank
17.32.2.
2 Sand cast iron SandS pipe as per IS: 1729. 2 3.00
17.32.2.
Centrifugally cast (spun) iron socketed pipe as per IS: 3989
2 1 1.00
Item no
1 2 3 4 5 6 7
Sub Engineer Sub Divisional Officer

PWD NH Sub Division PWD NH Sub Division
Indore/Kannod (M.P.) Indore/Kannod (M.P.)
NDORE - BETUL ROAD
Qty Unit Rate Amount

8 9 10 11
162.00
168.75
330.75 Cum 131 43328.00
165.38 Cum 30 4961.00
330.75
-27.00
-17.28
-9.72
-10.13
-7.50
-6.00
253.13 Cum 72 18225.00
83.63
83.63 Cum 471 39391.00
27.88
27.88 Cum 672 18733.00
8.10
8.10
8 9 10 11
8.10 Cum 4403 35664.00
27.00
17.28
7.50
6.00
3.80
4.33
2.83
13.94
82.68 cum. 4739 391840.00
72.00
57.60
129.60 Sqm. 174 22550.00
80.00
90.00
14.24
16.25
18.90
219.39 Sqm. 267 58577.00
9922.11 kg 62.90 624100.00

9922.11
Total A 1257369.00
8 9 10 11
9.45
7.56
4.75
5.42
17.50
44.67 cum. 5202 232369.00
1.43
0.63
0.17
6.10
2.83
11.16 cum. 5284 58974.00
6699.61 kg 62.90 421406.00
139.39 sqm. 264.00 36798.00

1.00 sqm. 264.00 264.00
121.96 sqm. 227.00 27685.00
213.40 sqm. 356.00 75970.00
50.97
50.97 cum. 5212.00 265648.00
8.50
8.50 cum. 5212.00 44319.00
8.50 cum. 184.00 1565.00

8 9 10 11
12.20
31.20
25.25
22.80
12.00
9.92
5.90
10.06
129.33 Rmt. 431.40 55793.00
8.06 Sqm 2888 23285.00
7.74
8 9 10 11
11.61
19.35 sqm. 2,423.00 46885.00
19.35 sqm. 401.00 7759.00
19.35 sqm. 453.00 8766.00
26.00 each 241.00 6266.00
52.00 each 82.00 4264.00
26.00 each 86.00 2236.00
13.00 each 1186.00 15418.00
2.00 each 2012.00 4024.00
26.00 each 74.00 1924.00

8 9 10 11
8.55
45.00
53.55 kg. 110.40 5912.00
5000.00 cm 4.60 23000.00
1.00 sqm 96.00 96.00
376.55
219.80
-7.74
-11.61
-8.06
42.52
611.45 sqm 110.00 67260.00
401.54
-7.92
-4.32
-3.07
386.23 sqm 128.00 49437.00
8 9 10 11
14.78 sqm. 885.00 13082.00
7.92
4.32
3.07
15.31
382.80 kg 91 34835.00
272.34 sqm. 62.00 16885.00

8 9 10 11
7.55
16.34
8.15
-3.15
28.88 sqm 937.00 27063.00
7.55
7.55 sqm 961.00 7252.00
139.39
139.39 sqm 1043.00 145380.00
12.96
6.48
158.83 sqm 1012.00 160732.00
7.74
11.61
19.35 sqm. 25.00 484.00
7.74
11.61
19.35 sqm. 77.00 1490.00
8 9 10 11
386.23 sqm. 74.00 28581.00
611.45 sqm 52.00 31796.00
611.45 sqm 64.00 39133.00
386.23 sqm 84 32443.00
1.00 sqm 60 60.00
7.92
4.32
3.07
1.03
2.21
18.55 sqm.
92.75 Kg 377 34966.00
8 9 10 11
92.75 Kg 425 39418.00
18.55 sqm. 932.00 17288.00

Total B 2118211.00
2 Each 2995.00 5990.00
3 Each 12764.00 38292.00
3 Each 4613.00 13839.00
3 Each 2460.00 7380.00
3 Each 459.00 1377.00

8 9 10 11
3 Each 659.00 1977.00
50.00 RM 207 10350.00

40.00 RM 234 9360.00
30.00 RM 288 8640.00
40.00 RM 360 14400.00
40.00 RM 122 4880.00

50.00 RM 141 7050.00
30.00 RM 185 5550.00
30.00 RM 238 7140.00
30.00 RM 324 9720.00
20.00 RM 498 9960.00
22.00 Each 458 10076.00
22.00 Each 778.00 17116.00
5.00 Each 486.00 2430.00

8.00 Each 558.00 4464.00
10.00 Each 677.00 6770.00
5.00 Each 976.00 4880.00
4.00 Each 316.00 1264.00
4000.00 Litre 7.00 28000.00

8 9 10 11
3.00 Each 1764.00 5292.00
151.40 RM 234.00 35428.00
120.00 RM 226.00 27120.00
60.00 RM 238.00 14280.00
15.00 Each 117.00 1755.00
15.00 Each 172.00 2580.00
15.00 Each 175.00 2625.00
15.00 Each 300.00 4500.00
15.00 Each 117.00 1755.00

15.00 Each 154.00 2310.00
20.00 Each 230.00 4600.00
20.00 Each 346.00 6920.00
15.00 Each 62.00 930.00

8 9 10 11
15.00 Each 50.00 750.00
4.00 each 7997.00 31988.00
1.00 Each 18086.00 18086.00
4.00 Mtr 6176.00 24704.00
2.00 Mtr 7380.00 14760.00
2.00 Each 6809.00 13618.00
1.00 Each 20609 20609.00
4.00 Each 266.00 1064.00
4302.00
6.00 Rmt 717.00
803.00
1.00 Rmt 803.00
TOTAL C 471684.00
8 9 10 11
G. Total A+B+C 3847264.00
Executive Engineer
PWD NH - Division
Indore (M.P.)

Estimate For Toll Plaza 16112015

Uploaded by

Copyright:

Available Formats

Estimate For Toll Plaza 16112015

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Read this document in other languages

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Estimate For Toll Plaza 16112015

Uploaded by

Copyright:

Available Formats

M. P.

PUBLIC WORKS DEPARTMENT, NH DIVISION, INDORE

DETAILED ESTIMATE FOR TOLL PLAZA

2 Location :- In km. 26/6 & 71/6

(ii) Stream of traffic on Toll Plaza - In reach of Km. 24 to 92 the main

2- Land for Toll Plaza (10.3) :-

4- Toll Booths (10.5) :-

5- Road Works (10.6) :-

9- Check / Barrier Gate (10.10) :-

10- Lighting (10.11) :-

11- Water Supply (10.12) :-

5 Specification :- MORT&H specification for road and bridge with up to date

Layout for Design of Toll Plaza

(1) For MS Pipe 110 mm 60 meter @ 15.86 Kg/Rmt = 951.60 Kg

Toll Plaza Automation System

Amout of Toll Plaza Complex Cost = 5824443.00

Toll booth Protection work

(1) For MS Pipe 110 mm 26.80 meter @ 15.86 Kg/Rmt

Excavation in Soil using Hydraulic Excavator and Tippers with disposal

Providing crushed stone aggregate, depositing on a prepared surface

Dry Lean Cement Concrete Sub- base (Construction of dry lean

(I) Mild Steel - Dowel Bar 32 mm @ 300 mm c/c length 500 mm

RCC Road Side Covered Drain

Providing Plain cement concrete M-15 nominal mix in foundation as

Supplying, fitting and placing HYSD bar reinforcement in substructure

Toll Plaza Island

for Other Island

Supplying, fitting and placing un-coated HYSD bar reinforcement in

43.84 @ 80 Kg from Above

(T1) Cantilever gantry sign for Toll Road strart

At Every 20 meter c/c

At every 30 meter c/c

Toll Plaza Complex

Amout of Toll Plaza Complex Cost = 5824443.00

Fire Fightening System

No. L (m) B (m) D (m) Unit

1 300 7.00 Sqm

1 300 40.00 0.150 Cum

1 300 37.00 0.500 Cum

2 300 3.20 0.690 Cum

2 300.00 1.30 1.00 Cum

2 300.00 1.30 0.15 117.00

300 0.20 Meter

4 23.70 1.800 0.200

6X2 1.30 0.800 Sqm

2x25 7.50 0.300

Sub Divisional Officer Executive Engineer

Layout for Design of Toll Plaza

(1) For MS Pipe 110 mm 60 meter @ 15.86 Kg/Rmt = 951.60 Kg

Amout of Toll Plaza Complex Cost = 5824443.00

Toll booth Protection work

(1) For MS Pipe 110 mm 26.80 meter @ 15.86 Kg/Rmt

Providing crushed stone aggregate, depositing on a prepared surface

Dry Lean Cement Concrete Sub- base (Construction of dry lean

(I) Mild Steel - Dowel Bar 32 mm @ 300 mm c/c length 500 mm

Construction of Shoulders with approved material/selected soil i/c

for Other Island