Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 27 views

    Torispherical Head Tolva

    Uploaded by

    Fabio Augusto Hincapie Henao
    This document summarizes the calculations for a torispherical head according to the ASME Section VIII Division 1 code. It provides the design data including dimensions, materials, and allowable stresses. It then shows the calculations to determine the minimum required thickness and maximum allowable working pressures for the head under both hot/corroded and new/cold conditions. It concludes that post-weld heat treatment is not required due to the amount of cold forming being less than 3.5%.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Torispherical Head Tolva

    Uploaded by

    Fabio Augusto Hincapie Henao
    27 views1 page
    This document summarizes the calculations for a torispherical head according to the ASME Section VIII Division 1 code. It provides the design data including dimensions, materials, and allowable stresses. It then shows the calculations to determine the minimum required thickness and maximum allowable working pressures for the head under both hot/corroded and new/cold conditions. It concludes that post-weld heat treatment is not required due to the amount of cold forming being less than 3.5%.

    Original Description:

    Calculo de Cabeza Toriesférica en Tolva

    Original Title

    Torispherical Head Tolva.xls

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document summarizes the calculations for a torispherical head according to the ASME Section VIII Division 1 code. It provides the design data including dimensions, materials, and allowable stresses. It then shows the calculations to determine the minimum required thickness and maximum allowable working pressures for the head under both hot/corroded and new/cold conditions. It concludes that post-weld heat treatment is not required due to the amount of cold forming being less than 3.5%.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    27 views1 page

    Torispherical Head Tolva

    Uploaded by

    Fabio Augusto Hincapie Henao
    This document summarizes the calculations for a torispherical head according to the ASME Section VIII Division 1 code. It provides the design data including dimensions, materials, and allowable stresses. It then shows the calculations to determine the minimum required thickness and maximum allowable working pressures for the head under both hot/corroded and new/cold conditions. It concludes that post-weld heat treatment is not required due to the amount of cold forming being less than 3.5%.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    ASME CODE CALCULATIONS SECTION VIII DIV.

    1 2004 EDITION
    2006 ADDENDA

    TORISPHERICAL HEAD CALCULATIONS JOB No. 101241

    1.0 Design Data

    Design Pressure P= 125,00 psi UG-22


    Design Temperature T= 300,00 °F UG-20
    Inside Diameter D= 23,722 inch
    Corrosion Allowance C= 0,0625 inch UG-25
    Head Material SA 36
    Allowable Stress at Design Temp. S= 16600 psi Sect IID,1A
    Allowable Stress at Ambient Temp. S= 16600 psi Sect IID,1A
    Cat.A Type and Exam./Cat. B Exam. Category A Type 2 None
    Head Efficiency E= 0,65 UW-12
    Crown Radius L= 9,840 inch 249,936 mm
    Knuckle Radius r= 4,250 inch 107,95 mm

    2.0 Head Thickness Calculations

    M=1/4(3+SQRT[(L+C)/(r+C)] M= 1,129

    t=P(L+C)M/(2SE-0.2P) t= 0,065 inch 1,65 mm


    treq=t + C treq= 0,127 inch 3,23 mm

    3.0 MAWP Calculations

    Minimum Thickness Selected t= 0,199 inch 5,05 mm


    Nominal Thickness Selected tnom= 0,199 inch 5,05 mm

    3.1 MAWP Hot and Corroded Calculations

    P=2SE(t-C)/[(L+C)M+0.2(t-C)] P= 262,88 psi


    MAWP=P-H MAWP= 262,88 psi

    3.2 MAWP New and Cold Calculations

    P=2SEt/(LM+0.2t) P= 387,15 psi


    MAWP=P-H MAWP= 387,15 psi

    4.0 PWHT Requirements for Cold Formed Parts

    Knuckle Radius r= 4,25 inch 107,95 mm


    Rf=r+tnom/2 Rf= 4,29 inch
    %=75tnom/Rf %= 3,48 %

    The Head requires PWHT because the cold forming operations: NO

    By Fabio A Hincapie

    You might also like