Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Vapor-Liquid Separator - Wikipedia

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

1/29/2018 Vapor–liquid separator - Wikipedia

Vapor–liquid separator
A vapor–liquid separator is a device used in several industrial
applications to separate a vapor–liquid mixture.

A vapor–liquid separator may also be referred to as a flash drum,


breakpot, knock-out drum or knock-out pot, compressor suction drum or
compressor inlet drum. When used to remove suspended water droplets
from streams of air, it is often called a demister.

Contents
Method of opera on
Liquid level monitoring

Where vapor–liquid separators are used


Preven ng pump damage
See also
References A typical vapor–liquid separator including
External links commonly a de-entrainment pad and
some mes an inlet distributor.

Method of operation
For the common variety, gravity is utilized in a vertical vessel to cause the liquid to settle to the bottom of the vessel, where
it is withdrawn.[1][2][3][4]

In low gravity environments such as a space station, a common liquid separator will not function because gravity is not
usable as a separation mechanism. In this case, centrifugal force needs to be utilised in a spinning centrifugal separator to
drive liquid towards the outer edge of the chamber for removal. Gaseous components migrate towards the center.

For both varieties of separator, the gas outlet may itself be surrounded by a spinning mesh screen or grating, so that any
liquid that does approach the outlet strikes the grating, is accelerated, and thrown away from the outlet.

The vapor travels through the gas outlet at a design velocity which minimises the entrainment of any liquid droplets in the
vapor as it exits the vessel.

The feed to a vapor–liquid separator may also be a liquid that is being partially or totally flashed into a vapor and liquid as
it enters the separator.

Liquid level monitoring

https://en.wikipedia.org/wiki/Vapor%E2%80%93liquid_separator 1/3
1/29/2018 Vapor–liquid separator - Wikipedia

The separator is only effective as long as there is an air space inside the chamber. The separator can fail if either the mixed
inlet is overwhelmed with supply material, or the liquid drain is unable to handle the volume of liquid being collected. The
separator may therefore be combined with some other liquid level sensing mechanism such as a sight glass or float sensor.
In this manner, both the supply and drain flow can be regulated to prevent the separator from becoming overloaded.
(Agastya, Bayu)

Where vapor–liquid separators are used


Vapor–liquid separators are very widely used in a great many industries and applications, such as:

Oil refineries
Natural-gas processing plants (NGL)
Petrochemical and chemical plants
Refrigera on systems
Air condi oning
Compressor systems
Gas pipelines
Steam condensate flash drums
Geothermal power plants
Combined cycle power plants
Flare stacks
Soil vapor extrac on
Paper mills

Preventing pump damage


In refrigeration systems, it is common for the system to contain a mixture of liquid and gas, but for the mechanical gas
compressor to be intolerant of liquid.

Some compressor types such as the scroll compressor use a continuously shrinking compression volume. Once liquid
completely fills this volume the pump may either stall and overload, or the pump chamber may be warped or otherwise
damaged by the fluid that can not fit into a smaller space.

See also
Flash evapora on
Vapor-compression refrigera on
Souders–Brown equa on (for sizing vapor–liquid separators)
Steam drum

References
1. William D. Baasel (1990). Preliminary Chemical engineering Plant Design (2nd ed.). Van Nostrand Reinhold. ISBN 0-442-23440-6.
OCLC 18907139 (h ps://www.worldcat.org/oclc/18907139).
2. David H.F. Liu (1997). Environmental Engineers' Handbook (2nd ed.). CRC Press. ISBN 0-8493-9971-8. OCLC 35886123 (h ps://w
ww.worldcat.org/oclc/35886123).

https://en.wikipedia.org/wiki/Vapor%E2%80%93liquid_separator 2/3
1/29/2018 Vapor–liquid separator - Wikipedia

3. Stanley S. Grossel (June 2004). "Design and sizing of knock-out drums/catchtanks for emergency relief systems".
Plant/Opera ons Progress (AIChE). 5 (3): 129–135. doi:10.1002/prsb.720050304 (h ps://doi.org/10.1002%2Fprsb.720050304).
ISSN 0278-4513 (h ps://www.worldcat.org/issn/0278-4513).
4. Stanley M. Walas (1988). Chemical Process Equipment:Selec on and Design. Bu erworth-Heinemann. ISBN 0-409-90131-8.
OCLC 16714037 (h ps://www.worldcat.org/oclc/16714037).

External links
Experimental Characteriza on of High-Pressure Natural Gas Scrubbers by Trond Austrheim (h p://web.i .uib.no/mps/mpstraus.
html) (preprints of papers based on PhD Thesis at the University of Bergen, Norway, 2006)
Flash Steam Tutorial (h p://www.spiraxsarco.com/resources/steam-engineering-tutorials/condensate-recovery/flash-steam.as
p) The benefits of recovering flash steam, how it is done and typical applica ons.
Quick Calculator for Horizontal Knock Out Drum sizing (h p://www.enggcyclopedia.com/calculators/equipment-sizing/2-phase-s
eparator-design-calculator-knock-drum/) Based on minimum me required for liquid droplets of a given minimum size to be
separated.
Design Criteria for Vapor/Liquid Separators (h p://www.red-bag.com/cms/index.php?sec on=242#criteria)
Detailed explana on of high performance vapor-liquid separators (scrubbers) (h p://www.ascomsep.com/index.php?hfst_id=4)
Vapor Liquid Separator designs and manufacturing process (h p://www.combus onindia.com)

Retrieved from "h ps://en.wikipedia.org/w/index.php? tle=Vapor–liquid_separator&oldid=808773814"

This page was last edited on 5 November 2017, at 02:08.

Text is available under the Crea ve Commons A ribu on-ShareAlike License; addi onal terms may apply. By using this site, you agree
to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark of the Wikimedia Founda on, Inc., a non-profit
organiza on.

https://en.wikipedia.org/wiki/Vapor%E2%80%93liquid_separator 3/3

You might also like